ASoC: use devm_snd_soc_register_card()

Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:

These are v2 to use devm_snd_soc_register_card() on ASoC.

ASoC: dt-bindings: fsl-sai: Support Rx-only SAI

On SoC like i.MX8QXP some SAI IP cores support only Rx path. Allow
specifying only an Rx DMA channel, while omitting the Tx one.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20231219122957.3358149-2-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: fsl-sai: Add power-domains

Some SoC like i.MX8QXP use a power-domain for this IP, so add it to the
supported properties.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20231219122957.3358149-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Support SAI and MICFIL on i.MX95 platform

Merge series from Chancel Liu <chancel.liu@nxp.com>:

Support SAI and MICFIL on i.MX95 platform

ASoC: Merge up fixes

To facilitate testing get our current fixes into the branch.

ASoC: codecs: add support for WCD939x Codec

Merge series from Neil Armstrong <neil.armstrong@linaro.org>:

Add the main WCD9390/WCD9395 Audio Codec driver to support:
- 4 ADC inputs for up to 5 Analog Microphones
- 4 DMIC inputs for up to 8 Digital Microphones
- 4 Microphone BIAS
- Stereo Headphone output
- Mono EAR output
- MBHC engine for Headset Detection

This adds:
- bindings
- MBHC changes to support Type-C muc
- Soundwire Slave driver
- Code driver

The USB Mux subsystem support will be submitted separately
since it's a functionally separate subsystem connected over
I2C with it's own reset signal.

Improve SOF support for Steam Deck OLED

Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:

This patch series is a continuation of [1] to provide several fixes and
improvements to the SOF drivers targeting the Vangogh platform, as found on
Valve's Steam Deck OLED.  The previous series only handled the legacy ACP
drivers.

Also note that, since v2, this patch series requires an updated SOF
topology to provide a correct DAI link ID for the BT codec.  The binary
file should be located under:

  /usr/lib/firmware/amd/sof-tplg/sof-vangogh-nau8821-max.tplg

Alternatively, as a temporary workaround, patch [2] can be used to adapt
the driver to the broken topology.

Another requirement to get this functional is patch [3] from v1, which has
been dropped from the series to be upstreamed via the SOF development
workflow.

[1]: https://lore.kernel.org/all/20231209203229.878730-1-cristian.ciocaltea@collabora.com/
[2]: https://lore.kernel.org/all/20231209205351.880797-11-cristian.ciocaltea@collabora.com/
[3]: https://lore.kernel.org/all/20231209205351.880797-12-cristian.ciocaltea@collabora.com/

ASoC: allow up to eight CPU/codec DAIs

Sound card on Qualcomm X1E80100 CRD board will use eight DAIs in one DAI
link, so increase the limit.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117160144.1305127-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: wcd934x: drop unneeded regulator include

Driver does not use any regulator code, so drop redundant include of
regulator/consumer.h header.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117151208.1219755-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: wcd938x: skip printing deferred probe failuers

Probe calls wcd938x_populate_dt_data() which already prints all the
error cases with dev_err_probe(), so skip the additional dev_err().

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117151208.1219755-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: wcd938x: handle deferred probe

WCD938x sound codec driver ignores return status of getting regulators
and returns EINVAL instead of EPROBE_DEFER.  If regulator provider
probes after the codec, system is left without probed audio:

  wcd938x_codec audio-codec: wcd938x_probe: Fail to obtain platform data
  wcd938x_codec: probe of audio-codec failed with error -22

Fixes: 16572522aece ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117151208.1219755-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: acp: Add check for cpu dai link initialization

Add condition check for cpu dai link initialization for amplifier
codec path, as same pcm id uses for both headset and speaker path
for RENOIR platforms.

Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://msgid.link/r/20240118143023.1903984-3-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: acp: Update platform name for different boards

Update platform name for various boards based on rembrandt
and renoir platforms.

Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://msgid.link/r/20240118143023.1903984-2-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: acp: Enable rt5682s clocks in acp slave mode

Set and enable rt5682s codec bclk and lrclk rates when
acp is in slave mode.

Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://msgid.link/r/20240118143023.1903984-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: wcd938x: fix headphones volume controls

The lowest headphones volume setting does not mute so the leave the TLV
mute flag unset.

This is specifically needed to let the sound server use the lowest gain
setting.

Fixes: c03226ba15fe ("ASoC: codecs: wcd938x: fix dB range for HPHL and HPHR")
Cc: <stable@vger.kernel.org> # 6.5
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240122091130.27463-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ti: j721e-evm: Use devm_kcalloc() instead of devm_kzalloc()

Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().

Link: https://github.com/KSPP/linux/issues/162
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Link: https://msgid.link/r/20240109181101.3806-1-erick.archer@gmx.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: nau8540: Add pre-charge actions for input

Adding pre-charge mechanism to make FEPGA power stable faster. It
not only improved the recording quality at the beginning but also
meaningfully decreased the final adc delay time.

Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Link: https://msgid.link/r/20240116024519.24569-1-CTLIN0@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: p1022_rdk: fix all kernel-doc warnings

Fix several kernel-doc warnings in p1022_rdk.c:

p1022_rdk.c:70: warning: cannot understand function prototype: 'struct machine_data '
p1022_rdk.c:90: warning: Function parameter or struct member 'card' not described in 'p1022_rdk_machine_probe'
p1022_rdk.c:90: warning: No description found for return value of 'p1022_rdk_machine_probe'
p1022_rdk.c:129: warning: Function parameter or struct member 'substream' not described in 'p1022_rdk_startup'
p1022_rdk.c:129: warning: No description found for return value of 'p1022_rdk_startup'
p1022_rdk.c:162: warning: Function parameter or struct member 'card' not described in 'p1022_rdk_machine_remove'
p1022_rdk.c:162: warning: No description found for return value of 'p1022_rdk_machine_remove'
p1022_rdk.c:187: warning: cannot understand function prototype: 'const struct snd_soc_ops p1022_rdk_ops = '
p1022_rdk.c:199: warning: Function parameter or struct member 'pdev' not described in 'p1022_rdk_probe'
p1022_rdk.c:199: warning: No description found for return value of 'p1022_rdk_probe'
p1022_rdk.c:349: warning: Function parameter or struct member 'pdev' not described in 'p1022_rdk_remove'
p1022_rdk.c:376: warning: No description found for return value of 'p1022_rdk_init'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: <linux-sound@vger.kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://msgid.link/r/20240111045736.7500-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: Do not override firmware-name $ref

dtschema package defines firmware-name as string-array, so individual
bindings should not make it a string but instead just narrow the number
of expected firmware file names.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240115182017.1610055-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: qcom: Use devm_kcalloc() instead of devm_kzalloc()

Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().

Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://msgid.link/r/20240106171635.19881-1-erick.archer@gmx.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: amd: Compute file paths on firmware load

Commit 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version fallback if
firmware files are missing") changed the order of some operations and
the firmware paths are not available anymore at snd_sof_probe() time.

Precisely, fw_filename_prefix is set by sof_select_ipc_and_paths() via

  plat_data->fw_filename_prefix = out_profile.fw_path;

but sof_init_environment() which calls this function was moved from
snd_sof_device_probe() to sof_probe_continue(). Moreover,
snd_sof_probe() was moved from sof_probe_continue() to
sof_init_environment(), but before the call to
sof_select_ipc_and_paths().

The problem here is that amd_sof_acp_probe() uses fw_filename_prefix to
compute fw_code_bin and fw_data_bin paths, and because the field is not
yet initialized, the paths end up containing (null):

snd_sof_amd_vangogh 0000:04:00.5: Direct firmware load for (null)/sof-vangogh-code.bin failed with error -2
snd_sof_amd_vangogh 0000:04:00.5: sof signed firmware code bin is missing
snd_sof_amd_vangogh 0000:04:00.5: error: failed to load DSP firmware -2
snd_sof_amd_vangogh: probe of 0000:04:00.5 failed with error -2

Move usage of fw_filename_prefix right before request_firmware() calls
in acp_sof_load_signed_firmware().

Fixes: 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version fallback if firmware files are missing")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-9-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: core: Skip firmware test for custom loaders

The ACP driver for Vangogh platform uses a quirk for Valve Galileo
device to setup a custom firmware loader, which neither requires nor
uses the firmware file indicated via the default_fw_filename member of
struct sof_dev_desc.

Since commit 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version
fallback if firmware files are missing"), the provided filename gets
verified and triggers a fatal error on probe:

[ 7.719337] snd_sof_amd_vangogh 0000:04:00.5: enabling device (0000 -> 0002)
[ 7.721486] snd_sof_amd_vangogh 0000:04:00.5: SOF firmware and/or topology file not found.
[ 7.721565] snd_sof_amd_vangogh 0000:04:00.5: Supported default profiles
[ 7.721569] snd_sof_amd_vangogh 0000:04:00.5: - ipc type 0 (Requested):
[ 7.721573] snd_sof_amd_vangogh 0000:04:00.5:  Firmware file: amd/sof/sof-vangogh.ri
[ 7.721577] snd_sof_amd_vangogh 0000:04:00.5:  Topology file: amd/sof-tplg/sof-vangogh-nau8821-max.tplg
[ 7.721582] snd_sof_amd_vangogh 0000:04:00.5: Check if you have 'sof-firmware' package installed.
[ 7.721585] snd_sof_amd_vangogh 0000:04:00.5: Optionally it can be manually downloaded from:
[ 7.721589] snd_sof_amd_vangogh 0000:04:00.5:    https://github.com/thesofproject/sof-bin/
[ 7.721997] snd_sof_amd_vangogh: probe of 0000:04:00.5 failed with error -2

According to AMD, a combined ".ri" file which includes the code and data
segments cannot be used due to a limitation preventing the code image to
be signed on build time.

Fix the issue by skipping the firmware file test if a custom loader is
being used instead of the generic one.

Fixes: 6c393ebbd74a ("ASoC: SOF: core: Implement IPC version fallback if firmware files are missing")
Co-developed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-8-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: amd: Optimize quirk for Valve Galileo

Valve's Steam Deck OLED is uniquely identified by vendor and product
name (Galileo) DMI fields.

Simplify the quirk by removing the unnecessary match on product family.

Additionally, fix the related comment as it points to the old product
variant.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-7-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: amd: Fix memory leak in amd_sof_acp_probe()

Driver uses kasprintf() to initialize fw_{code,data}_bin members of
struct acp_dev_data, but kfree() is never called to deallocate the
memory, which results in a memory leak.

Fix the issue by switching to devm_kasprintf(). Additionally, ensure the
allocation was successful by checking the pointer validity.

Fixes: f7da88003c53 ("ASoC: SOF: amd: Enable signed firmware image loading for Vangogh platform")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-6-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: acp: Update MODULE_DESCRIPTION for sof-mach

The current MODULE_DESCRIPTION relates to a Chrome board, as that was
what the driver initially supported.

Nonetheless, it has since progressed incrementally and evolved into a
more comprehensive machine driver. Hence, update MODULE_DESCRIPTION to
better reflect this.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-5-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: acp: Add missing error handling in sof-mach

Handle potential acp_sofdsp_dai_links_create() errors in ACP SOF machine
driver's probe function.  Note there is no need for an undo.

While at it, switch to dev_err_probe().

Fixes: 9f84940f5004 ("ASoC: amd: acp: Add SOF audio support on Chrome board")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-4-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: acp: Make use of existing *_CODEC_DAI macros

The generic ACP machine driver provides macros for NAU88221 and MAX98388
codec DAI names, but in places it is still using directly the related
strings.

For consistency, replace all strings with the equivalent macros.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-3-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: amd: acp: Drop redundant initialization of machine driver data

Simplify driver data configuration by removing redundant initialization
of members in static structs.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: Add WCD939x Codec driver

Add the main WCD9390/WCD9395 Audio Codec driver to support:
- 4 ADC inputs for up to 5 Analog Microphones
- 4 DMIC inputs for up to 8 Digital Microphones
- 4 Microphone BIAS
- Stereo Headphone output
- Mono EAR output
- MBHC engine for Headset Detection

It makes usage of the generic MBHC and CLSH generic code and
the USB Type-C mux and switch helpers to gather USB-C Events
in order to properly setup Headset Detection mechanism
when connected behind the separate USB-C Mux subsystem.

WCD9390/WCD9395 supports a PCM path for Playback instead
of the actually implemented PDM playback, it will be
implemented later.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://msgid.link/r/20231219-topic-sm8650-upstream-wcd939x-codec-v4-5-1c3bbff2d7ab@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: Add WCD939x Soundwire devices driver

Add Soundwire Slave driver for the WCD9390/WCD9395 Audio Codec.

The WCD9390/WCD9395 Soundwire devices will be used by the
main WCD9390/WCD9395 Audio Codec driver to access registers
and configure Soundwire RX and TX ports.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://msgid.link/r/20231219-topic-sm8650-upstream-wcd939x-codec-v4-4-1c3bbff2d7ab@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codec: wcd-mbhc-v2: add support when connected behind an USB-C audio mux

When the WCD codec is connected behind an USB-C audio mux,
plug/unplug events, clock control, pull-up and threshold are
different.
Add a typec_analog_mux config enabling those changes and add
two callbacks to trigger plug/unplug events from USB-C events.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://msgid.link/r/20231219-topic-sm8650-upstream-wcd939x-codec-v4-3-1c3bbff2d7ab@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: document WCD939x Audio Codec

Document the Qualcomm WCD9390/WCD9395 Audio Codec and the
Soundwire devices than can be found on Qualcomm SM8650 based platforms.

The Qualcomm WCD9390/WCD9395 Audio Codec communicates
with the host SoC over 2 Soundwire links to provide:
- 4 ADC inputs for up to 5 Analog Microphones
- 4 DMIC inputs for up to 8 Digital Microphones
- 4 Microphone BIAS
- Stereo Headphone output
- Mono EAR output
- MBHC engine for Headset Detection

The WCD9390/WCD9395 IC has separate I2C subsystem for USB-C
DP Altmode/Audio Accessory mode Mux which is not documented
here but requires port/endpoint graph and properties to handle
Altmode/Audio Accessory switch and orientation.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://msgid.link/r/20231219-topic-sm8650-upstream-wcd939x-codec-v4-2-1c3bbff2d7ab@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: qcom,wcd938x: move out common properties

Move out common properties from qcom,wcd938x bindings in preparation
of adding Qualcomm WCD939x bindings sharing most of the properties.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://msgid.link/r/20231219-topic-sm8650-upstream-wcd939x-codec-v4-1-1c3bbff2d7ab@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: fsl,micfil: Add compatible string for i.MX95 platform

Add compatible string "fsl,imx95-micfil" for i.MX95 platform.

Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240112054331.3244104-4-chancel.liu@nxp.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: fsl_sai: Add support for i.MX95 platform

Add compatible string and specific soc data to support SAI on i.MX95
platform.

Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://msgid.link/r/20240112054331.3244104-3-chancel.liu@nxp.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: fsl,sai: Add compatible string for i.MX95 platform

Add compatible string "fsl,imx95-sai" for i.MX95 platform.

Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240112054331.3244104-2-chancel.liu@nxp.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: atmel: use devm_snd_soc_register_card()

Let's use devm_snd_soc_register_card() instead of snd_soc_register_card()
and ignore snd_soc_unregister_card()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://msgid.link/r/87wmsgwv4r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: fsl: use devm_snd_soc_register_card()

Let's use devm_snd_soc_register_card() instead of snd_soc_register_card()
and ignore snd_soc_unregister_card()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://msgid.link/r/87y1cwwv51.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ti: use devm_snd_soc_register_card()

Let's use devm_snd_soc_register_card() instead of snd_soc_register_card()
and ignore snd_soc_unregister_card()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://msgid.link/r/87zfxcwv58.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 6.8-rc1

Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Merge tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Merge tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

bcachefs: Improve inode_to_text()

Add line breaks - inode_to_text() is now much easier to read.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: logged_ops_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: reflink_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs; extents_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: ec_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: subvolume_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: snapshot_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: alloc_background_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: xattr_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: dirent_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: inode_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs; quota_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: sb-counters_format.h

bcachefs_format.h has gotten too big; let's do some organizing.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: counters.c -> sb-counters.c

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: comment bch_subvolume

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch_snapshot::btime

Add a field to bch_snapshot for creation time; this will be important
when we start exposing the snapshot tree to userspace.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: add missing __GFP_NOWARN

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: opts->compression can now also be applied in the background

The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Prep work for variable size btree node buffers

bcachefs btree nodes are big - typically 256k - and btree roots are
pinned in memory. As we're now up to 18 btrees, we now have significant
memory overhead in mostly empty btree roots.

And in the future we're going to start enforcing that certain btree node
boundaries exist, to solve lock contention issues - analagous to XFS's
AGIs.

Thus, we need to start allocating smaller btree node buffers when we
can. This patch changes code that refers to the filesystem constant
c->opts.btree_node_size to refer to the btree node buffer size -
btree_buf_bytes() - where appropriate.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: grab s_umount only if snapshotting

When I was testing mongodb over bcachefs with compression,
there is a lockdep warning when snapshotting mongodb data volume.

$ cat test.sh
prog=bcachefs

$prog subvolume create /mnt/data
$prog subvolume create /mnt/data/snapshots

while true;do
    $prog subvolume snapshot /mnt/data /mnt/data/snapshots/$(date +%s)
    sleep 1s
done

$ cat /etc/mongodb.conf
systemLog:
  destination: file
  logAppend: true
  path: /mnt/data/mongod.log

storage:
  dbPath: /mnt/data/

lockdep reports:
[ 3437.452330] ======================================================
[ 3437.452750] WARNING: possible circular locking dependency detected
[ 3437.453168] 6.7.0-rc7-custom+ #85 Tainted: G            E
[ 3437.453562] ------------------------------------------------------
[ 3437.453981] bcachefs/35533 is trying to acquire lock:
[ 3437.454325] ffffa0a02b2b1418 (sb_writers#10){.+.+}-{0:0}, at: filename_create+0x62/0x190
[ 3437.454875]
               but task is already holding lock:
[ 3437.455268] ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.456009]
               which lock already depends on the new lock.

[ 3437.456553]
               the existing dependency chain (in reverse order) is:
[ 3437.457054]
               -> #3 (&type->s_umount_key#48){.+.+}-{3:3}:
[ 3437.457507]        down_read+0x3e/0x170
[ 3437.457772]        bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.458206]        __x64_sys_ioctl+0x93/0xd0
[ 3437.458498]        do_syscall_64+0x42/0xf0
[ 3437.458779]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.459155]
               -> #2 (&c->snapshot_create_lock){++++}-{3:3}:
[ 3437.459615]        down_read+0x3e/0x170
[ 3437.459878]        bch2_truncate+0x82/0x110 [bcachefs]
[ 3437.460276]        bchfs_truncate+0x254/0x3c0 [bcachefs]
[ 3437.460686]        notify_change+0x1f1/0x4a0
[ 3437.461283]        do_truncate+0x7f/0xd0
[ 3437.461555]        path_openat+0xa57/0xce0
[ 3437.461836]        do_filp_open+0xb4/0x160
[ 3437.462116]        do_sys_openat2+0x91/0xc0
[ 3437.462402]        __x64_sys_openat+0x53/0xa0
[ 3437.462701]        do_syscall_64+0x42/0xf0
[ 3437.462982]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.463359]
               -> #1 (&sb->s_type->i_mutex_key#15){+.+.}-{3:3}:
[ 3437.463843]        down_write+0x3b/0xc0
[ 3437.464223]        bch2_write_iter+0x5b/0xcc0 [bcachefs]
[ 3437.464493]        vfs_write+0x21b/0x4c0
[ 3437.464653]        ksys_write+0x69/0xf0
[ 3437.464839]        do_syscall_64+0x42/0xf0
[ 3437.465009]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.465231]
               -> #0 (sb_writers#10){.+.+}-{0:0}:
[ 3437.465471]        __lock_acquire+0x1455/0x21b0
[ 3437.465656]        lock_acquire+0xc6/0x2b0
[ 3437.465822]        mnt_want_write+0x46/0x1a0
[ 3437.465996]        filename_create+0x62/0x190
[ 3437.466175]        user_path_create+0x2d/0x50
[ 3437.466352]        bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.466617]        __x64_sys_ioctl+0x93/0xd0
[ 3437.466791]        do_syscall_64+0x42/0xf0
[ 3437.466957]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.467180]
               other info that might help us debug this:

[ 3437.469670] 2 locks held by bcachefs/35533:
               other info that might help us debug this:

[ 3437.467507] Chain exists of:
                 sb_writers#10 --> &c->snapshot_create_lock --> &type->s_umount_key#48

[ 3437.467979]  Possible unsafe locking scenario:

[ 3437.468223]        CPU0                    CPU1
[ 3437.468405]        ----                    ----
[ 3437.468585]   rlock(&type->s_umount_key#48);
[ 3437.468758]                                lock(&c->snapshot_create_lock);
[ 3437.469030]                                lock(&type->s_umount_key#48);
[ 3437.469291]   rlock(sb_writers#10);
[ 3437.469434]
                *** DEADLOCK ***

[ 3437.469670] 2 locks held by bcachefs/35533:
[ 3437.469838]  #0: ffffa0a02ce00a88 (&c->snapshot_create_lock){++++}-{3:3}, at: bch2_fs_file_ioctl+0x1e3/0xc90 [bcachefs]
[ 3437.470294]  #1: ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.470744]
               stack backtrace:
[ 3437.470922] CPU: 7 PID: 35533 Comm: bcachefs Kdump: loaded Tainted: G            E      6.7.0-rc7-custom+ #85
[ 3437.471313] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 3437.471694] Call Trace:
[ 3437.471795]  <TASK>
[ 3437.471884]  dump_stack_lvl+0x57/0x90
[ 3437.472035]  check_noncircular+0x132/0x150
[ 3437.472202]  __lock_acquire+0x1455/0x21b0
[ 3437.472369]  lock_acquire+0xc6/0x2b0
[ 3437.472518]  ? filename_create+0x62/0x190
[ 3437.472683]  ? lock_is_held_type+0x97/0x110
[ 3437.472856]  mnt_want_write+0x46/0x1a0
[ 3437.473025]  ? filename_create+0x62/0x190
[ 3437.473204]  filename_create+0x62/0x190
[ 3437.473380]  user_path_create+0x2d/0x50
[ 3437.473555]  bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.473819]  ? lock_acquire+0xc6/0x2b0
[ 3437.474002]  ? __fget_files+0x2a/0x190
[ 3437.474195]  ? __fget_files+0xbc/0x190
[ 3437.474380]  ? lock_release+0xc5/0x270
[ 3437.474567]  ? __x64_sys_ioctl+0x93/0xd0
[ 3437.474764]  ? __pfx_bch2_fs_file_ioctl+0x10/0x10 [bcachefs]
[ 3437.475090]  __x64_sys_ioctl+0x93/0xd0
[ 3437.475277]  do_syscall_64+0x42/0xf0
[ 3437.475454]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.475691] RIP: 0033:0x7f2743c313af
======================================================

In __bch2_ioctl_subvolume_create(), we grab s_umount unconditionally
and unlock it at the end of the function. There is a comment
"why do we need this lock?" about the lock coming from
commit 42d237320e98 ("bcachefs: Snapshot creation, deletion")
The reason is that __bch2_ioctl_subvolume_create() calls
sync_inodes_sb() which enforce locked s_umount to writeback all dirty
nodes before doing snapshot works.

Fix it by read locking s_umount for snapshotting only and unlocking
s_umount after sync_inodes_sb().

Signed-off-by: Su Yue <glass.su@suse.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: kvfree bch_fs::snapshots in bch2_fs_snapshots_exit

bch_fs::snapshots is allocated by kvzalloc in __snapshot_t_mut.
It should be freed by kvfree not kfree.
Or umount will triger:

[  406.829178 ] BUG: unable to handle page fault for address: ffffe7b487148008
[  406.830676 ] #PF: supervisor read access in kernel mode
[  406.831643 ] #PF: error_code(0x0000) - not-present page
[  406.832487 ] PGD 0 P4D 0
[  406.832898 ] Oops: 0000 [#1] PREEMPT SMP PTI
[  406.833512 ] CPU: 2 PID: 1754 Comm: umount Kdump: loaded Tainted: G           OE      6.7.0-rc7-custom+ #90
[  406.834746 ] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[  406.835796 ] RIP: 0010:kfree+0x62/0x140
[  406.836197 ] Code: 80 48 01 d8 0f 82 e9 00 00 00 48 c7 c2 00 00 00 80 48 2b 15 78 9f 1f 01 48 01 d0 48 c1 e8 0c 48 c1 e0 06 48 03 05 56 9f 1f 01 <48> 8b 50 08 48 89 c7 f6 c2 01 0f 85 b0 00 00 00 66 90 48 8b 07 f6
[  406.837810 ] RSP: 0018:ffffb9d641607e48 EFLAGS: 00010286
[  406.838213 ] RAX: ffffe7b487148000 RBX: ffffb9d645200000 RCX: ffffb9d641607dc4
[  406.838738 ] RDX: 000065bb00000000 RSI: ffffffffc0d88b84 RDI: ffffb9d645200000
[  406.839217 ] RBP: ffff9a4625d00068 R08: 0000000000000001 R09: 0000000000000001
[  406.839650 ] R10: 0000000000000001 R11: 000000000000001f R12: ffff9a4625d4da80
[  406.840055 ] R13: ffff9a4625d00000 R14: ffffffffc0e2eb20 R15: 0000000000000000
[  406.840451 ] FS:  00007f0a264ffb80(0000) GS:ffff9a4e2d500000(0000) knlGS:0000000000000000
[  406.840851 ] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  406.841125 ] CR2: ffffe7b487148008 CR3: 000000018c4d2000 CR4: 00000000000006f0
[  406.841464 ] Call Trace:
[  406.841583 ]  <TASK>
[  406.841682 ]  ? __die+0x1f/0x70
[  406.841828 ]  ? page_fault_oops+0x159/0x470
[  406.842014 ]  ? fixup_exception+0x22/0x310
[  406.842198 ]  ? exc_page_fault+0x1ed/0x200
[  406.842382 ]  ? asm_exc_page_fault+0x22/0x30
[  406.842574 ]  ? bch2_fs_release+0x54/0x280 [bcachefs]
[  406.842842 ]  ? kfree+0x62/0x140
[  406.842988 ]  ? kfree+0x104/0x140
[  406.843138 ]  bch2_fs_release+0x54/0x280 [bcachefs]
[  406.843390 ]  kobject_put+0xb7/0x170
[  406.843552 ]  deactivate_locked_super+0x2f/0xa0
[  406.843756 ]  cleanup_mnt+0xba/0x150
[  406.843917 ]  task_work_run+0x59/0xa0
[  406.844083 ]  exit_to_user_mode_prepare+0x197/0x1a0
[  406.844302 ]  syscall_exit_to_user_mode+0x16/0x40
[  406.844510 ]  do_syscall_64+0x4e/0xf0
[  406.844675 ]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[  406.844907 ] RIP: 0033:0x7f0a2664e4fb

Signed-off-by: Su Yue <glass.su@suse.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bios must be 512 byte algined

Fixes: 023f9ac9f70f bcachefs: Delete dio read alignment check
Reported-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: remove redundant variable tmp

The variable tmp is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so tmp can be
removed.

Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the enclosing
expression, the value is never actually read from 'ret'
[deadcode.DeadStores]

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Improve trace_trans_restart_relock

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Fix excess transaction restarts in __bchfs_fallocate()

drop_locks_do() should not be used in a fastpath without first trying
the do in nonblocking mode - the unlock and relock will cause excessive
transaction restarts and potentially livelocking with other threads that
are contending for the same locks.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: extents_to_bp_state

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bkey_and_val_eq()

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Better journal tracepoints

Factor out bch2_journal_bufs_to_text(), and use it in the
journal_entry_full() tracepoint; when we can't get a journal reservation
we need to know the outstanding journal entry sizes to know if the
problem is due to excessive flushing.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Print size of superblock with space allocated

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Avoid flushing the journal in the discard path

When issuing discards, we may need to flush the journal if there's too
many buckets that can't be discarded until a journal flush.

But the heuristic was bad; we should be comparing the number of buckets
that need to flushes against the number of free buckets, not the number
of buckets we saw.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Improve move_extent tracepoint

Also print out the data_opts, so that we can see what specifically is
being done to an extent.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Add missing bch2_moving_ctxt_flush_all()

This fixes a bug with rebalance IOs getting stuck with reads completed,
but writes never being issued.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Re-add move_extent_write tracepoint

It appears this was accidentally deleted at some point - also, do a bit
of cleanup.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_kthread_io_clock_wait() no longer sleeps until full amount

Drop t he loop in bch2_kthread_io_clock_wait(): this allows the code
that uses it to be woken up for other reasons, and fixes a bug where
rebalance wouldn't wake up when a scan was requested.

This raises the possibility of spurious wakeups, but callers should
always be able to handle that reasonably well.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Add .val_to_text() for KEY_TYPE_cookie

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Don't pass memcmp() as a pointer

Some (buggy!) compilers have issues with this.

Fixes: https://github.com/koverstreet/bcachefs/issues/625
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Merge tag 'header_cleanup-2024-01-20' of https://evilpiepirate.org/git/bcachefs

Pull header fix from Kent Overstreet:
 "Just one small fixup for the RT build"

* tag 'header_cleanup-2024-01-20' of https://evilpiepirate.org/git/bcachefs:
  spinlock: Fix failing build for PREEMPT_RT

bcachefs: Reduce would_deadlock restarts

We don't have to take locks in any particular ordering - we'll make
forward progress just fine - but if we try to stick to an ordering, it
can help to avoid excessive would_deadlock transaction restarts.

This tweaks the reflink path to take extents btree locks in the right
order.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_trans_account_disk_usage_change()

The disk space accounting rewrite is splitting out accounting for each
replicas set - those are moving to btree keys, instead of percpu
counters.

This breaks bch2_trans_fs_usage_apply() up, splitting out the part we
will still need.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch_fs_usage_base

Split out base filesystem usage into its own type; prep work for
breaking up bch2_trans_fs_usage_apply().

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_prt_compression_type()

bounds checking helper, since compression types are extensible

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: helpers for printing data types

We need bounds checking since new versions may introduce new data types.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: BTREE_TRIGGER_ATOMIC

Add a new flag to be explicit about when we're running atomic triggers.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: drop to_text code for obsolete bps in alloc keys

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: eytzinger_for_each() declares loop iter

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Don't log errors if BCH_WRITE_ALLOC_NOWAIT

Previously, we added logging in the write path to ensure that any
unexpected errors getting reported to userspace have a log message; but
BCH_WRITE_ALLOC_NOWAIT is a special case, it's used for promotes where
errors are expected and not reported out to userspace - so we need to
silence those.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: fix memleak in bch2_split_devs

The pointer dev_name can be modified by strseq(),
then causes the memleak:

unreferenced object 0xffff9d08a2916c80 (size 32):
  comm "mount.bcachefs", pid 9090, jiffies 4295856224 (age 17.564s)
  hex dump (first 32 bytes):
    2f 64 65 76 2f 6d 61 70 70 65 72 2f 74 65 73 74  /dev/mapper/test
    2d 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00  -0..............
  backtrace:
    [<00000000c5d3be7d>] __kmem_cache_alloc_node+0x1f3/0x2c0
    [<0000000052215d26>] __kmalloc_node_track_caller+0x51/0x150
    [<0000000069fea956>] kstrdup+0x32/0x60
    [<000000000877fcf1>] bch2_split_devs+0x3f/0x150 [bcachefs]
    [<000000007ee93204>] bch2_mount+0xcb/0x640 [bcachefs]
    [<000000002dd1e04b>] legacy_get_tree+0x30/0x60
    [<000000006afc31d3>] vfs_get_tree+0x28/0xf0
    [<000000007b0c538e>] path_mount+0x475/0xb60
    [<0000000092de5882>] __x64_sys_mount+0x105/0x140
    [<0000000054fc05d8>] do_syscall_64+0x42/0xf0
    [<00000000df584910>] entry_SYSCALL_64_after_hwframe+0x6e/0x76

Fix it by copy pointer dev_name at beginning and free the copied
pointer at end.

Signed-off-by: Su Yue <glass.su@suse.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Merge tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6

Pull smb client updates from Steve French:
 "Various smb client fixes, including multichannel and for SMB3.1.1
  POSIX extensions:

   - debugging improvement (display start time for stats)

   - two reparse point handling fixes

   - various multichannel improvements and fixes

   - SMB3.1.1 POSIX extensions open/create parsing fix

   - retry (reconnect) improvement including new retrans mount parm, and
     handling of two additional return codes that need to be retried on

   - two minor cleanup patches and another to remove duplicate query
     info code

   - two documentation cleanup, and one reviewer email correction"

* tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update iface_last_update on each query-and-update
  cifs: handle servers that still advertise multichannel after disabling
  cifs: new mount option called retrans
  cifs: reschedule periodic query for server interfaces
  smb: client: don't clobber ->i_rdev from cached reparse points
  smb: client: get rid of smb311_posix_query_path_info()
  smb: client: parse owner/group when creating reparse points
  smb: client: fix parsing of SMB3.1.1 POSIX create context
  cifs: update known bugs mentioned in kernel docs for cifs
  cifs: new nt status codes from MS-SMB2
  cifs: pick channel for tcon and tdis
  cifs: open_cached_dir should not rely on primary channel
  smb3: minor documentation updates
  Update MAINTAINERS email address
  cifs: minor comment cleanup
  smb3: show beginning time for per share stats
  cifs: remove redundant variable tcon_exist

Merge tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine

Pull dmaengine updates from Vinod Koul:
 "New support:
   - Loongson LS2X APB DMA controller
   - sf-pdma: mpfs-pdma support
   - Qualcomm X1E80100 GPI dma controller support

  Updates:
   - Xilinx XDMA updates to support interleaved DMA transfers
   - TI PSIL threads for AM62P and J722S and cfg register regions
     description
   - axi-dmac Improving the cyclic DMA transfers
   - Tegra Support dma-channel-mask property
   - Remaining platform remove callback returning void conversions

 Driver fixes for:
   - Xilinx xdma driver operator precedence and initialization fix
   - Excess kernel-doc warning fix in imx-sdma xilinx xdma drivers
   - format-overflow warning fix for rz-dmac, sh usb dmac drivers
   - 'output may be truncated' fix for shdma, fsl-qdma and dw-edma
     drivers"

* tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (58 commits)
  dmaengine: dw-edma: increase size of 'name' in debugfs code
  dmaengine: fsl-qdma: increase size of 'irq_name'
  dmaengine: shdma: increase size of 'dev_id'
  dmaengine: xilinx: xdma: Fix kernel-doc warnings
  dmaengine: usb-dmac: Avoid format-overflow warning
  dmaengine: sh: rz-dmac: Avoid format-overflow warning
  dmaengine: imx-sdma: fix Excess kernel-doc warnings
  dmaengine: xilinx: xdma: Fix initialization location of desc in xdma_channel_isr()
  dmaengine: xilinx: xdma: Fix operator precedence in xdma_prep_interleaved_dma()
  dmaengine: xilinx: xdma: statify xdma_prep_interleaved_dma
  dmaengine: xilinx: xdma: Workaround truncation compilation error
  dmaengine: pl330: issue_pending waits until WFP state
  dmaengine: xilinx: xdma: Implement interleaved DMA transfers
  dmaengine: xilinx: xdma: Prepare the introduction of interleaved DMA transfers
  dmaengine: xilinx: xdma: Add transfer error reporting
  dmaengine: xilinx: xdma: Add error checking in xdma_channel_isr()
  dmaengine: xilinx: xdma: Rework xdma_terminate_all()
  dmaengine: xilinx: xdma: Ease dma_pool alignment requirements
  dmaengine: xilinx: xdma: Add necessary macro definitions
  dmaengine: xilinx: xdma: Get rid of unused code
  ...

Merge tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux

Pull coccinelle updates from Julia Lawall:
 "Updates to the device_attr_show semantic patch to reflect the new
  guidelines of the Linux kernel documentation.

  The problem was identified by Li Zhijian <lizhijian@fujitsu.com>, who
  proposed an initial fix"

* tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  coccinelle: device_attr_show: simplify patch case
  coccinelle: device_attr_show: Adapt to the latest Documentation/filesystems/sysfs.rst

media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)

This patch replaces max(a, min(b, c)) by clamp(b, a, c) in the solo6x10
driver.  This improves the readability and more importantly, for the
solo6x10-p2m.c file, this reduces on my system (x86-64, gcc 13):

 - the preprocessed size from 121 MiB to 4.5 MiB;

 - the build CPU time from 46.8 s to 1.6 s;

 - the build memory from 2786 MiB to 98MiB.

In fine, this allows this relatively simple C file to be built on a
32-bit system.

Reported-by: Jiri Slaby <jirislaby@gmail.com>
Closes: https://lore.kernel.org/lkml/18c6df0d-45ed-450c-9eda-95160a2bbb8e@gmail.com/
Cc: <stable@vger.kernel.org> # v6.7+
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: David Laight <David.Laight@ACULAB.COM>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coccinelle: device_attr_show: simplify patch case

Replacing the final expression argument by ... allows the format
string to have multiple arguments.

It also has the advantage of allowing the change to be recognized as
a change in a single statement, thus avoiding adding unneeded braces.

Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>

execve: open the executable file before doing anything else

No point in allocating a new mm, counting arguments and environment
variables etc if we're just going to return ENOENT.

This patch does expose the fact that 'do_filp_open()' that execve() uses
is still unnecessarily expensive in the failure case, because it
allocates the 'struct file *' early, even if the path lookup (which is
heavily optimized) fails.

So that remains an unnecessary cost in the "no such executable" case,
but it's a separate issue.  Regardless, I do not want to do _both_ a
filename_lookup() and a later do_filp_open() like the origin patch by
Josh Triplett did in [1].

Reported-by: Josh Triplett <josh@joshtriplett.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mateusz Guzik <mjguzik@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/lkml/5c7333ea4bec2fad1b47a8fa2db7c31e4ffc4f14.1663334978.git.josh@joshtriplett.org/
Link: https://lore.kernel.org/lkml/202209161637.9EDAF6B18@keescook/
Link: https://lore.kernel.org/lkml/CAHk-=wgznerM-xs+x+krDfE7eVBiy_HOam35rbsFMMOwvYuEKQ@mail.gmail.com/
Link: https://lore.kernel.org/lkml/CAHk-=whf9qLO8ipps4QhmS0BkM8mtWJhvnuDSdtw5gFjhzvKNA@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux

Pull more RISC-V updates from Palmer Dabbelt:

 - Support for tuning for systems with fast misaligned accesses.

 - Support for SBI-based suspend.

 - Support for the new SBI debug console extension.

 - The T-Head CMOs now use PA-based flushes.

 - Support for enabling the V extension in kernel code.

 - Optimized IP checksum routines.

 - Various ftrace improvements.

 - Support for archrandom, which depends on the Zkr extension.

 - The build is no longer broken under NET=n, KUNIT=y for ports that
   don't define their own ipv6 checksum.

* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
  lib: checksum: Fix build with CONFIG_NET=n
  riscv: lib: Check if output in asm goto supported
  riscv: Fix build error on rv32 + XIP
  riscv: optimize ELF relocation function in riscv
  RISC-V: Implement archrandom when Zkr is available
  riscv: Optimize hweight API with Zbb extension
  riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
  samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
  riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
  riscv: ftrace: Make function graph use ftrace directly
  riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
  lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
  riscv: Restrict DWARF5 when building with LLVM to known working versions
  riscv: Hoist linker relaxation disabling logic into Kconfig
  kunit: Add tests for csum_ipv6_magic and ip_fast_csum
  riscv: Add checksum library
  riscv: Add checksum header
  riscv: Add static key for misaligned accesses
  asm-generic: Improve csum_fold
  RISC-V: selftests: cbo: Ensure asm operands match constraints
  ...

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI updates from James Bottomley:
 "Final round of fixes that came in too late to send in the first
  request.

  It's nine bug fixes and one version update (because of a bug fix) and
  one set of PCI ID additions. There's one bug fix in the core which is
  really a one liner (except that an additional sdev pointer was added
  for convenience) and the rest are in drivers"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: target: core: Add TMF to tmr_list handling
  scsi: core: Kick the requeue list after inserting when flushing
  scsi: fnic: unlock on error path in fnic_queuecommand()
  scsi: fcoe: Fix unsigned comparison with zero in store_ctlr_mode()
  scsi: mpi3mr: Fix mpi3mr_fw.c kernel-doc warnings
  scsi: smartpqi: Bump driver version to 2.1.26-030
  scsi: smartpqi: Fix logical volume rescan race condition
  scsi: smartpqi: Add new controller PCI IDs
  scsi: ufs: qcom: Remove unnecessary goto statement from ufs_qcom_config_esi()
  scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
  scsi: ufs: core: Simplify power management during async scan

Merge tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux

Pull sh updates from John Paul Adrian Glaubitz:
 "Since the large patch series to convert arch/sh to device tree support
  has not been finalized yet due to various maintainers still asking for
  changes to the series, this ended up being rather small consisting of
  just two fixes.

  The first patch by Geert Uytterhoeven addresses a build failure in the
  EcoVec platform code. And the second patch by Masahiro Yamada removes
  an unnecessary $(foreach ...) found in a Makefile of the vsyscall
  code.

   - Rename missed backlight field from fbdev to dev

   - Remove unnecessary $(foreach ...)"

* tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
  sh: vsyscall: Remove unnecessary $(foreach ...)
  sh: ecovec24: Rename missed backlight field from fbdev to dev

Merge tag 'fbdev-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev

Pull fbdev fix from Helge Deller:
 "There were various reports from people without any graphics output on
  the screen and it turns out one commit triggers the problem.

   - Revert 'firmware/sysfb: Clear screen_info state after consuming it'"

* tag 'fbdev-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
  Revert "firmware/sysfb: Clear screen_info state after consuming it"