Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit fd3e165ac8be7bfbc47318e7b720458a5d5d6227) Signed-off-by: Brian Maly <brian.maly@oracle.com>
CC: stable@vger.kernel.org Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit d5573584429254a14708cf8375c47092b5edaf2c) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Until now the megaraid_sas driver has reported successful completion on
SYNCHRONIZE_CACHE commands without sending them down to the controller.
The controller firmware has been responsible for taking care of flushing
disk caches for all drives that belong to a Virtual Disk at the time of
system reboot/shutdown.
There may have been a reason to avoid sending SYNCHRONIZE_CACHE to a VD
in the past but that no longer appears to be valid.
Older versions of MegaRaid firmware (Gen2 and Gen2.5) set the WCE bit
for Virtual Disks but the firmware does not report correct completion
status for a SYNCHRONIZE_CACHE command. As a result, we must use another
method to identify whether it is safe to send the command to the
controller. We use the canHandleSyncCache firmware flag in the scratch
pad register at offset 0xB4.
New SYNCHRONIZE_CACHE behavior:
IF 'JBOD'
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware sends SYNCHRONIZE_CACHE to drive
Firmware obtains status from drive and returns same status back to driver
ELSEIF 'VirtualDisk'
IF firmware supports new API bit called canHandleSyncCache
Driver sends SYNCHRONIZE_CACHE command to the firmware
Firmware does not send SYNCHRONIZE_CACHE to drives
Firmware returns SUCCESS
ELSE
Driver does not send SYNCHRONIZE_CACHE command to the firmware
Driver return SUCCESS for that command
ENDIF
ENDIF
[mkp: edited patch description]
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit d0fc91d67c59068ce6d42e41ce66a4c471e5bc74) Signed-off-by: Brian Maly <brian.maly@oracle.com>
This patch addresses the issue of driver firing DCMDs in PCI
shutdown/detach path irrespective of firmware state. Driver will now
check whether firmware is in operational state or not before firing
DCMDs. If firmware is in unrecoverable state or does not become
operational within specfied time, driver will skip firing DCMDs.
[mkp: fixed typos]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit a1dfd62c1ebce71a62f5de002c694d5a22fb32a1) Signed-off-by: Brian Maly <brian.maly@oracle.com>
This patch fixes the issue of wrong PhysArm was sent to firmware for R1
VD downgrade.
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit b3e3827bdd329da1c1b5697e74dfcaf51b65885c) Signed-off-by: Brian Maly <brian.maly@oracle.com>
For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds. As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.
CC: stable@vger.kernel.org Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 18e1c7f68a5814442abad849abe6eacbf02ffd7c) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Commit 02b01e010afe ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010afeeb49328d35650d70721d2ca3fd59 CC: stable@vger.kernel.org Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 1e793f6fc0db920400574211c48f9157a37e3945) Signed-off-by: Brian Maly <brian.maly@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/megaraid/megaraid_sas_fusion.c:281:1: warning: no previous prototype for 'megasas_free_cmds_fusion' [-Wmissing-prototypes]
drivers/scsi/megaraid/megaraid_sas_fusion.c:714:1: warning: no previous prototype for 'megasas_ioc_init_fusion' [-Wmissing-prototypes]
....
In fact, these functions are declared in
drivers/scsi/megaraid/megaraid_sas_base.c, but should be declared in a
header file, thus can be recognized in other file.
So this patch adds the declarations into
drivers/scsi/megaraid/megaraid_sas_fusion.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 2f3e77323d3159cb6c2a002fa6c58ba22e7c837e) Signed-off-by: Brian Maly <brian.maly@oracle.com>
A dev_printk message spans two lines and the literal string is missing a
white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 4086eae52beab7808b8aa1a9f7d4095eebc247c7) Signed-off-by: Brian Maly <brian.maly@oracle.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(unsigned long)' which is likely to
be 4.
It is likely that the number of bits in a long was expected here, so use
BITS_PER_LONG instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 51f9039ffd751dee54fe26609df645bfd128b1d0) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Conflicts:
drivers/scsi/megaraid/megaraid_sas_base.c
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 709ab231f8b4417411147dd9730928ba214d5c31) Signed-off-by: Brian Maly <brian.maly@oracle.com>
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b4c ("megaraid_sas: Use lowest memory bar for SR-IOV VF support") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit e7f851684efb3377e9c93aca7fae6e76212e5680) Signed-off-by: Brian Maly <brian.maly@oracle.com>
There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ). Below are the error logs reported
continuously-
Jun 25 08:49:30 ns8 kernel: [ 757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [ 757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY. In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.
Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.
Reported-by: Lucz Geza <geza@lucz.com> Cc: <stable@vger.kernel.org> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit d9083160c2f6ee456ea867ea2279c1fc6124e56f) Signed-off-by: Brian Maly <brian.maly@oracle.com>
I actually read the error messages in my logs, and successful
initialization is not an error.
Arguably these log lines could be deleted entirely.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Hannes Reinicke <hare@suse.de> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 13f307711b127d30fcf333a04365a217baf9ca2b) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 54c4042852a85713a7bdd8436cc63762049fbb39) Signed-off-by: Brian Maly <brian.maly@oracle.com>
This patch will do code optmization for task management functions.
Below are key changes:
1. Remove reset_device hook as it was not being used and driver was
setting this to NULL.
2. Create wrapper functions for task abort and target reset and inside
these functions adapter specific calls be made. e.g. fusion adapters
support task abort and target reset so task abort and target reset
should be issued to fusion adapters only and for MFI adapters, print
a message saying feature not supported.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit bd23d4abe5edf09dfba086d44b7972cf73c14b0b) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Conflicts:
drivers/scsi/megaraid/megaraid_sas_base.c
In OCR path, before calling chip reset calls function
megasas_wait_for_outstanding_fusion to check reason for OCR. In case of
firmware FAULT initiated OCR and DCMD timeout initiated timeout, driver
will clear any outstanding reply (yet to be processed by driver) in
reply queues before going for chip reset. This code is added to handle a
scenario when IO timeout initiated adapter reset and management
application initiated adapter reset (by sending command to FAULT
firmware) happens simultaneously since adapter reset function is
safe-guarded by reset_mutex so only thread will be doing controller
reset. Consider IO timeout thread gets mutex and proceeds with adapter
reset process after disabling interrupts and by the time management
application has fired command to firmware to do adapter reset and the
same command is completed by firmware but since interrupts are disabled,
driver will not get completion and the same command will be in
outstanding/pending commands list of driver and refires same command
from IO timeout thread after chip reset which will again FAULT firmware
and eventually causes kill adapter.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 64d0b8e4a6f7e9a3c366c2df93ec1f003d180ca3) Signed-off-by: Brian Maly <brian.maly@oracle.com>
This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode. Driver will not allocate memory for optional and
perfromance oriented features. Below are key changes done in
megaraid_sas driver to do this:
1. Limit Controller's queue depth to 100 in kdump mode.
2. Do not allocate memory for system info buffer and PD info buffer.
3. Disable performance oriented features e.g. Disable RDPQ mode, disable
dual queue depth, restrict to single MSI-x vector.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit c3e385a1b985a9202ba7fbd0bdbdcb909905d00c) Signed-off-by: Brian Maly <brian.maly@oracle.com>
gcc-6 found a dubious indentation in the megasas_mgmt_fw_ioctl
function:
drivers/scsi/megaraid/megaraid_sas_base.c: In function 'megasas_mgmt_fw_ioctl':
drivers/scsi/megaraid/megaraid_sas_base.c:6658:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
kbuff_arr[i] = NULL;
^~~~~~~~~
drivers/scsi/megaraid/megaraid_sas_base.c:6653:3: note: ...this 'if' clause, but it is not
if (kbuff_arr[i])
^~
The code is actually correct, as there is no downside in clearing a NULL
pointer again.
This clarifies the code and avoids the warning by adding extra curly
braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 90dc9d98f01b ("megaraid_sas : MFI MPT linked list corruption fix") Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 3deb9438d34a09f6796639b652a01d110aca9f75) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Johannes Thumshirn [Wed, 3 Aug 2016 13:00:18 +0000 (15:00 +0200)]
mpt3sas: Don't spam logs if logging level is 0
In _scsih_io_done() we test if the ioc->logging_level does _not_ have
the MPT_DEBUG_REPLY bit set and if it hasn't we print the debug
messages. This unfortunately is the wrong way around.
Note, the actual bug is older than af0094115 but this commit removed the
CONFIG_SCSI_MPT3SAS_LOGGING Kconfig option which hid the bug.
Fixes: af0094115 'mpt2sas, mpt3sas: Remove SCSI_MPTXSAS_LOGGING entry from Kconfig' Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: Chaitra P B <chaitra.basappa@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 0d667f72b2a20bbac72bec0ab11467fc70bb0f1f)
Changes to support new security states of the iLO5 firmware.
- use BAR5 for CCB's for iLO5
- simplification of error handling
Signed-off-by: Mark Rusk <mark.rusk@hpe.com> Signed-off-by: David Altobelli <david.altobelli@hpe.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit c9fef1cc3dd3677633e6fd6ea5bd7ef3b741fab3) Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com> Reviewed-by: Brian Maly <brian.maly@oracle.com>
Dave Carroll [Thu, 9 Feb 2017 18:04:47 +0000 (11:04 -0700)]
scsi: aacraid: Fix INTx/MSI-x issue with older controllers
commit 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang")
caused a problem on older controllers which do not support MSI-x (namely
ASR3405,ASR3805). This patch conditionalizes the previous patch to
controllers which support MSI-x
Cc: <stable@vger.kernel.org> # v4.7+ Fixes: 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang") Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 8af8e1c22f9994bb1849c01d66c24fe23f9bc9a0)
Kevin Barnett [Thu, 8 Dec 2016 16:29:29 +0000 (10:29 -0600)]
scsi: aacraid: remove wildcard for series 9 controllers
Controllers with this PCI ID never shipped outside of
PMCS/Microsemi. Remove the ID from the aacraid driver. smartpqi is the
correct driver for these controllers.
[mkp: patch description]
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit ae2aae2421983f6f68eb7c4692624bc43ea50712)
We get 1 warning when building kernel with W=1:
drivers/scsi/aacraid/src.c:616:5: warning: no previous prototype for 'aac_src_select_comm' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static. so this patch
marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Dave Carroll <david.carroll@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit a44199eee7fdd2791b39da88938e6de6f5058632)
Muhammad Falak R Wani [Thu, 19 May 2016 14:08:33 +0000 (19:38 +0530)]
aacraid: use kmemdup
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 22e9f5a61666ed1145a09fbe49ac1a6f2ae7be8e)
Hannes Reinecke [Wed, 18 May 2016 08:16:51 +0000 (10:16 +0200)]
aacraid: do not activate events on non-SRC adapters
Only SRC-based adapters support the AifReqEvent function, so there is no
point in trying to activate it on older, non-SRC based adapters. Doing
so lead to crashes on older adapters.
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAaditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 787ab6e97024926f38773287d9f98a9b330bce23)
When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Cc: stable@vger.kernel.org Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 78cbccd3bd683c295a44af8050797dc4a41376ff)
Currently driver completes double completed or spurious interrupted fibs.
This is not necessary and causes the SCSI mid layer to issue aborts and
resets, since completing a fib prematurely might trigger a race condition
resulting in the driver not calling the scsi_done callback.
Fixed by removing the call to fib complete.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit eef76f16295d34d7fab6994b82dda60ce002f91d)
Firmware AIF messages about cache loss and data recovery are being missed
by the driver since currently they are not captured but rather let go.
This patch to capture those messages and log them for the user.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 9cb62fa24e0d22dbe991c315d6c454a341ea3f76)
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout() Cc: stable@vger.kernel.org Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit fc4bf75ea300a5e62a2419f89dd0e22189dd7ab7)
Orabug: 25505509 Signed-off-by: Dhaval Giani <dhaval.giani@oracle.com>
aacraid: Disable MSI mode for series 6, 7, 8 cards
As the firmware for series 6, 7, 8 cards does not support msi, remove it
in the driver
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit e4d5c4e238999ba0b68618a91eec33e7079cdbd4)
aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.
Fixed by replacing "cpu_relax()" call with "schedule()" Cc: stable@vger.kernel.org Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Orabug: 25505509 Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 07beca2be24cc710461c0b131832524c9ee08910) Signed-off-by: Dhaval Giani <dhaval.giani@oracle.com>
Suggested-by: Seymour, Shane M <shane.seymour@hpe.com> Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit a6cd4549af54ee1ba70a77661499828ea5a2bb3c)
Current driver checks for NULL return from aac_fib_alloc_tag, but it not
possible for it to return NULL.
Fixed by: Remove all the checks for NULL returns from aac_fib_alloc_tag
Suggested-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit da31df8c7285910ee8c8629d901b34a480ab0005)
Arnd Bergmann [Mon, 14 Mar 2016 14:29:43 +0000 (15:29 +0100)]
aacraid: add missing curly braces
gcc-6 warns about obviously wrong indentation for newly added code in
aac_slave_configure():
drivers/scsi/aacraid/linit.c: In function 'aac_slave_configure':
drivers/scsi/aacraid/linit.c:458:3: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
sdev->tagged_supported = 1;
^~~~
drivers/scsi/aacraid/linit.c:455:4: note: ...this 'else' clause, but it is not
gcc is correct, and evidently this was meant to be within the curly
braces that should have been there to start with. This patch adds them,
which avoids the warning and makes it clear what was intended here.
Nothing changes in behavior because in the 'if' block, the
sdev->tagged_supported flag is known to be set already.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 6bf3b630d0a7 ("aacraid: SCSI blk tag support") Reviewed-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 548f0e65a38f36976260a63ff4acfa9f3b17307d)
The method to allocate and free FIB's in the present code utilizes
spinlocks. Multiple IO's have to wait on the spinlock to acquire or free
fibs creating a performance bottleneck.
An alternative solution would be to use block layer tags to keep track
of the fibs allocated and freed. To this end aac_fib_alloc_tag was
created to utilize the blk layer tags to plug into the Fib pool.These
functions are used exclusively in the IO path. 8 fibs are reserved for
the use of AIF management software and utilize the previous spinlock
based implementations.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@pmcs.com> Reviewed-by: Shane Seymour <shane.seymour@hpe.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6bf3b630d0a733b74f7167a1cfac457358e67074)
During EEH PCI hotplug activity kernel unloads and loads the driver,
causing character device to be unregistered(aac_remove_one).When the
driver is loaded back using aac_probe_one the character device needs
to be registered again for the AIF management tools to work.
Fixed by adding code to register character device in aac_probe_one if
it is unregistered in aac_remove_one.
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Reviewed-by: Shane Seymour <shane.seymour@hpe.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit b9fb54b425e14658959bbc753452aaaf4d11d6fa)
while driver removal is in progress or PCI shutdown is invoked, driver
kills AIF aacraid thread, but IOCTL requests from the management tools
re-start AIF thread leading to IOP_RESET.
Fixed by setting adapter_shutdown flag when PCI shutdown is invoked.
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Reviewed-by: Shane Seymour <shane.seymour@hpe.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit fbd185986ebafaeac900a1af1829fed2bf03242e)
aac_mutex was used to create protect the ioctl path for only the compat
path, it would be make more sense to place mutex in aac_do_ioctl, which
is the main ioctl function call that handles all ioctl commands.
Created new mutex ioctl_mutex in struct aac_dev to protect switch case
in aac_do_ioctl and removed aac_mutex from aac_cfg_ioctl and
aac_compat_do_ioctl
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@pmcs.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 222a9fb376df0f4aec32493a3fb5d18fa56979f2)
Series 7 does not support PCI hot reset used by EEH.
Enabled fundamental reset only for Series 7
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6b93b7dd85dc0788eedc6ad30ff0b01ad9d4c657)
During EEH recovery number of online CPU's might change thereby changing
the number of MSIx vectors. Since each fib is allocated to a vector,
changes in the number of vectors causes fib to be sent thru invalid
vectors.In addition the correct number of MSIx vectors is not updated in
the INIT struct sent to the controller, when it is reinitialized.
Fixed by reassigning vectors to fibs based on the updated number of MSIx
vectors and updating the INIT structure before sending to controller.
Fixes: MSI-X vector calculation for suspend/resume Cc: stable@vger.kernel.org Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Reviewed-by: Shane Seymour <shane.seymour@hpe.com> Reviewed-by: Johannes Thumshirn <jthushirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit ecc479e00db8eb110b200afe1effcb3df20ca7ae)
Added support for PCI EEH (extended error handling).
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 5c63f7f710bdde6454d304a84146a5338962a509)
Mahesh Rajashekhara [Fri, 28 Aug 2015 10:38:34 +0000 (06:38 -0400)]
aacraid: Add Power Management support
* .suspend() and .resume() routines implemented in the driver
* aac_release_resources() initiates firmware shutdown
* aac_acquire_resources re-initializes the host interface
Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com> Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com> Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
(cherry picked from commit de665f28f788ad72ff6a0ce6ac2721d77248b7cf)
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Brian Maly <brian.maly@oracle.com>
The driver was calculating the adapter command pagesize indicator from
the system pagesize. However, the buffers the driver allocates are only
one size (SLI4_PAGE_SIZE), so no calculation was necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Brian Maly <brian.maly@oracle.com>
This patch does a cleanup and fixes few small typos in lpfc_scsi.c
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com> Signed-off-by: James Smart <james.smart@avagotech.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 4b160ae8a34983f11635981168760412ed3c2cfa) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Driver could reference stale node pointers in task mgmt call.
Changed to use resetting cmd and look up node pointer in task mgmt
function.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit eed695d70e7eff55595f222b55b96f105d4a27ca) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Correct issue leading to oops during link reset. Missing vport pointer.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit e6c6acc0e0223ddaf867628d420ee196349c6fae) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Correct error in setting OS Driver Version with FW. Prior length was
too short.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@Suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit b2fd103b05feabbc86db726ae121da94639892d7) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Clear the VendorVersion in the PLOGI/PLOGI ACC payload
Vendor version info may have been set on fabric login. Before sending
PLOGI payloads, ensure that it's cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit e0165f20447c8ca1d367725ee94d8ec9f38ca275) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Correct host name in symbolic_name field of nameserver registrations
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6c9231f604c2575be24c96d38deb70f145172f92) Signed-off-by: Brian Maly <brian.maly@oracle.com>
FCoE VPort enable-disable does not bring up the VPort.
VPI structure needed to be initialized before being re-registered.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 104450eb08ca662e6b1d02da11aca9598e978f3e) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Fix Xlane dynamic LUN set for LUN priority. Dynamic changing of the
priority was not getting reflected on the LUN.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit b5749fe182a0fa1c39ea1b33c0691d436f269195) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Deprecate lpfc_prot_sg_seg_cnt parameter. Eliminates driver from
unnecessarily limiting DIF s/g list length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit f2bf460cf5ef989f0a593d05932460326376d5f6) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Correct oops on vport port resets. Incorrect WQE type, thus the clearing
code actually overstepped the WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 2f07784f05c23b322863274e801c31aa64e46c71) Signed-off-by: Brian Maly <brian.maly@oracle.com>
On loosely ordered memory systems (PPC for example), the WQE elements
were being updated in memory, but not necessarily flushed before the
separate doorbell was written to hw which would cause hw to dma the
WQE element. Thus, the hardware occasionally received partially
updated WQE data.
Add the memory barrier after updating the WQE memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6b3b3bdb83b4ad51252d21bb13596db879e51850) Signed-off-by: Brian Maly <brian.maly@oracle.com>
The BUG_ON() recently introduced in lpfc_sli_ringtxcmpl_put() is hit in
the lpfc_els_abort() > lpfc_sli_issue_abort_iotag() >
lpfc_sli_abort_iotag_issue() function path [similar names], due to
'piocb->vport == NULL':
BUG_ON(!piocb || !piocb->vport);
This happens because lpfc_sli_abort_iotag_issue() doesn't set the
'abtsiocbp->vport' pointer -- but this is not the problem.
Previously, lpfc_sli_ringtxcmpl_put() accessed 'piocb->vport' only if
'piocb->iocb.ulpCommand' is neither CMD_ABORT_XRI_CN nor
CMD_CLOSE_XRI_CN, which are the only possible values for
lpfc_sli_abort_iotag_issue():
So, this function path would not have hit this possible NULL pointer
dereference before.
In order to fix this regression, move the second part of the BUG_ON()
check prior to the pointer dereference that it does check for.
For reference, this is the stack trace observed. The problem happened
because an unsolicited event was received - a PLOGI was received after
our PLOGI was issued but not yet complete, so the discovery state
machine goes on to sw-abort our PLOGI.
Cc: stable@vger.kernel.org # v4.8 Fixes: 22466da5b4b7 ("lpfc: Fix possible NULL pointer dereference") Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com> Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 2319f847a8910cff1d46c9b66aa1dd7cc3e836a9) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Check for the existence of piocb->vport before accessing it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: James Smart <james.smart@broadcom.com> Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 22466da5b4b7a82d3e5a9c21c752cae91a21dc91) Signed-off-by: Brian Maly <brian.maly@oracle.com>
A recent bugfix introduced a harmless warning in the lpfc driver:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_write_firmware':
drivers/scsi/lpfc/lpfc_logmsg.h:56:45: error: format '%ld' expects argument of type 'long int', but argument 9 has type 'size_t {aka const unsigned int}' [-Werror=format=]
'size_t' is always the same width as 'long' in the kernel, but the
compiler doesn't know that. The %z modifier is what the standard expects
to be used here, and this shuts up the warning.
Fixes: 679053c651fb ("scsi: lpfc: Fix fw download on SLI-4 FC adapters") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit efe583c6d3cdafbeb0c039cd5d0f88fd26637065) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Driver performs a quick validation of magic numbers in the fw
download image. Driver needed to be updated for more recent
magic numbers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6b6ef5db2590f0f6b99ba25fb018b60653ea66fe) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Link speed settings set by the boot driver are reported by the hw.
Driver will attempt to read them, and if set, will respect their
values.
The driver can override the settings with its own if instructed by
user space (via bsg), with the new values being picked up by the
boot driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit c691816e00d0b4da376f005ffc06eec8a9711dcf) Signed-off-by: Brian Maly <brian.maly@oracle.com>
We were having double completions on our SLI-3 version of adapters.
Solved by clearing our command pointer before calling scsi_done.
The eh paths potentially ran simulatenously and would see the non-null
value and invoke scsi_done again.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 89533e9be08aeda5cdc4600d46c1540c7b440299) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Change reject code to something that allows a retry
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 401304cc0d508de2e366e693fedbe52b18aef0a8) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6c86068dd235b61af9bfdcb8d3ec0d98ccbcf5a6) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 0cfbbf2f9672c07637427f24768647a7fe19bd75) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit ed5b152913971aeac12751f313655358ca2ab6e4) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 0a0354398cf8775c40973bcfa60ec8d5a72ee58d) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 506139a23eff91c365098fe9cc418e0fdcc5b660) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 31202b0e3c8dded6623a13ea0033a7bf03121c0a) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 0d8c8ba3fa5e21eebf36ef7ab7e370622309ac1c) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 61bda8f7c3ce46ce5de7c91a3383f7fe963643b9) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Correct embedded io wq element size. Embedded element sizes are
128 byte elements
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit dc58f44c2140748d96e33a533cd9e80692f58518) Signed-off-by: Brian Maly <brian.maly@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/lpfc/lpfc_sli.c:5693:1: warning: no previous prototype for 'lpfc_set_features' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:8972:1: warning: no previous prototype for 'lpfc_sli_calc_ring' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4621:1: warning: no previous prototype for 'lpfc_rdp_res_link_service' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4633:1: warning: no previous prototype for 'lpfc_rdp_res_sfp_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4698:1: warning: no previous prototype for 'lpfc_rdp_res_link_error' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4727:1: warning: no previous prototype for 'lpfc_rdp_res_bbc_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4752:1: warning: no previous prototype for 'lpfc_rdp_res_oed_temp_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4780:1: warning: no previous prototype for 'lpfc_rdp_res_oed_voltage_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4809:1: warning: no previous prototype for 'lpfc_rdp_res_oed_txbias_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4838:1: warning: no previous prototype for 'lpfc_rdp_res_oed_txpower_desc' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit bd4b3e5c8adf2b9f601b46b917afac555be05688) Signed-off-by: Brian Maly <brian.maly@oracle.com>
When building with -Wextra, we get a lot of warnings for the lpfc driver
concerning expressions that are always true, starting with:
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_enable_npiv_init':
drivers/scsi/lpfc/lpfc_attr.c:2786:77: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_enable_rrq_init':
drivers/scsi/lpfc/lpfc_attr.c:2802:76: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_suppress_link_up_init':
drivers/scsi/lpfc/lpfc_attr.c:2812:2050: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_log_verbose_init':
drivers/scsi/lpfc/lpfc_attr.c:3064:1930: error: comparison of unsigned expression >= 0 is always true [-Werror=type-limits]
The code works as intended, but it would be nice to shut up the warning
so we don't clutter up build logs with this. Using a separate inline
function for it makes it clear to the compiler that the comparison is
necessary in the caller but still lets it do the constant-folding.
[mkp: fix typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit de8c36bba33380fcc8564e69c039a4b84166e66d) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Call lpfc_sli_validate_fcp_iocb() with the hbalock held, as the pointer
to iocbq is not guaranteed to still be valid after looking it up.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Laurence Oberman <loberman@redhat.com> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 31979008fdae72d7441643f3a5b1bdaedf481335) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 51f4ca3c93b2eaf80a182e9fcfa4f9e5706cca12) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 115a4124bae6697b375e150deaed3a4ffc6580e1) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Re-organize source for easier driver attribute management
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 93dd1911cf4913321d91aa9c525f5f8149f90fee) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Remove global lpfc_sli_mode attribute in leiu of per-hba lpfc_sli_mode
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 12247e8101eacfda790a14944c34bdccb6e90d6b) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Remove global lpfc_delay_discovery attribute in leiu of per-hba
lpfc_delay_discovery
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 8eb8b960fd0593baaddd1c01cbff6b85c5056ccf) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Remove global lpfc_enable_npiv attribute in leiu of per-hba lpfc_enable_npiv
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 458c083e83ed2f8e446cf1a38dd21996cebe6da0) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Correct Port reset resulting in FC port going offline
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 0e916ee71d2f0453dbfe402cd8ca24f9668518ad) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit c92c841cc72ae7eb665fb9ea2a1c991e214c3807) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 5b1993dedfdc131ff095c0c079ef106aed3fe9ac) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Re-organize source for easier device-id management
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 12f4445733c516648ab0b013314a83467876ac2f) Signed-off-by: Brian Maly <brian.maly@oracle.com>
Correct FCOE discovery to avoid loss of storage devices after system reboot
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit a1cadfeffac70a1ed77b45a8f93b92b9cb501d94) Signed-off-by: Brian Maly <brian.maly@oracle.com>
projects / users / jedix / linux-maple.git / log