Matthew Schwartz [Thu, 11 Sep 2025 17:48:51 +0000 (10:48 -0700)]
drm/amd/display: Only restore backlight after amdgpu_dm_init or dm_resume
On clients that utilize AMD_PRIVATE_COLOR properties for HDR support,
brightness sliders can include a hardware controlled portion and a
gamma-based portion. This is the case on the Steam Deck OLED when using
gamescope with Steam as a client.
When a user sets a brightness level while HDR is active, the gamma-based
portion and/or hardware portion are adjusted to achieve the desired
brightness. However, when a modeset takes place while the gamma-based
portion is in-use, restoring the hardware brightness level overrides the
user's overall brightness level and results in a mismatch between what
the slider reports and the display's current brightness.
To avoid overriding gamma-based brightness, only restore HW backlight
level after boot or resume. This ensures that the backlight level is
set correctly after the DC layer resets it while avoiding interference
with subsequent modesets.
Fixes: 7875afafba84 ("drm/amd/display: Fix brightness level not retained over reboot") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4551 Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Guangshuo Li [Thu, 18 Sep 2025 10:57:05 +0000 (18:57 +0800)]
drm/amdgpu/atom: Check kcalloc() for WS buffer in amdgpu_atom_execute_table_locked()
kcalloc() may fail. When WS is non-zero and allocation fails, ectx.ws
remains NULL while ectx.ws_size is set, leading to a potential NULL
pointer dereference in atom_get_src_int() when accessing WS entries.
Return -ENOMEM on allocation failure to avoid the NULL dereference.
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 27 Aug 2025 09:45:45 +0000 (11:45 +0200)]
drm/amdgpu: revert to old status lock handling v3
It turned out that protecting the status of each bo_va with a
spinlock was just hiding problems instead of solving them.
Revert the whole approach, add a separate stats_lock and lockdep
assertions that the correct reservation lock is held all over the place.
This not only allows for better checks if a state transition is properly
protected by a lock, but also switching back to using list macros to
iterate over the state of lists protected by the dma_resv lock of the
root PD.
v2: re-add missing check
v3: split into two patches
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Sunil Khatri <sunil.khatri@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: add missing comment for the new argument
In function 'amdgpu_vm_lock_done_list' update the comment
for the new argument 'vm'.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202509180211.UAqME0zj-lkp@intel.com/ Signed-off-by: Sunil Khatri <sunil.khatri@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 17 Sep 2025 16:42:11 +0000 (12:42 -0400)]
drm/amdgpu: suspend KFD and KGD user queues for S0ix
We need to make sure the user queues are preempted so
GFX can enter gfxoff.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org> Tested-by: David Perry <david.perry@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 17 Sep 2025 16:42:10 +0000 (12:42 -0400)]
drm/amdgpu/userq: Optimize S0ix handling
In S0i3, GFX state is retained, so it's preferrable to
preempt queues rather than unmapping them as the overhead
is lower.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org> Tested-by: David Perry <david.perry@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
AMDGPU_PTE_PRT_GFX12 flag is missed during pageTable rework, add it back.
Fixes: 6716a823d18d ("drm/amdgpu: rework how PTE flags are generated v3") Signed-off-by: Joe Wang <joe.wang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 17 Sep 2025 16:42:09 +0000 (12:42 -0400)]
drm/amdkfd: add proper handling for S0ix
When in S0i3, the GFX state is retained, so all we need to do
is stop the runlist so GFX can enter gfxoff.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org> Tested-by: David Perry <david.perry@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 20 Aug 2025 20:04:18 +0000 (16:04 -0400)]
drm/amdgpu: remove non-DC DCE 11 code
DC has been the default for ~8 years now and supports
many things that the non-DC code does not (audio, DP MST, etc.).
No DCE 11.x IPs ever supported analog encoders so that is not
an issue. Finally drop this code.
Acked-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Asad Kamal [Mon, 15 Sep 2025 12:28:49 +0000 (20:28 +0800)]
drm/amd/pm: Enable npm metrics data
Enable npm metrics data for smu_v13_0_12
v3: Add node id check for setting NPM_CAPS (Lijo)
Signed-off-by: Asad Kamal <asad.kamal@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Asad Kamal [Fri, 29 Aug 2025 04:25:54 +0000 (12:25 +0800)]
drm/amd/pm: Fetch npm data from system metrics table
Fetch npm data from system metrics table for smu_v13_0_12
v3: Remove intermittent type for npm data, remove node id check,
move npm caps check to npm_get_data function (Lijo)
Signed-off-by: Asad Kamal <asad.kamal@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Asad Kamal [Wed, 27 Aug 2025 13:22:13 +0000 (21:22 +0800)]
drm/amd/pm: Add sysfs node for node power
Add sysfs node to expose node power limit for smu_v13_0_12
v2: Remove support check from visible function (Kevin)
v3: Update comments (Kevin)
Remove sysfs remove file, change format specifier
for sysfs_emit, use attribute_group.name (Lijo)
Signed-off-by: Asad Kamal <asad.kamal@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Asad Kamal [Mon, 15 Sep 2025 09:53:19 +0000 (17:53 +0800)]
drm/amd/pm: Allow system metrics table in 1vf mode
Allow fetching system metrics table in 1VF mode
Signed-off-by: Asad Kamal <asad.kamal@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 27 Aug 2025 09:45:45 +0000 (11:45 +0200)]
drm/amdgpu: re-order and document VM code
Re-order fields in the VM structure and try to improve the
documentation a bit.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Sunil Khatri <sunil.khatri@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 27 Aug 2025 08:17:48 +0000 (10:17 +0200)]
drm/amdgpu: remove check for BO reservation add assert instead
We should leave such checks to lockdep and not implement something
manually.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Sunil Khatri <sunil.khatri@amd.com> Reviewed-by: Prike Liang <Prike.Liang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Asad Kamal [Wed, 27 Aug 2025 10:19:13 +0000 (18:19 +0800)]
drm/amd/pm: Update pmfw headers for smu_v13_0_12
Update pmfw headers for smu_v13_0_12 to include node power limit
Signed-off-by: Asad Kamal <asad.kamal@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rename amdgpu_hwmon_get_sensor_generic to use for generic pm
interfaces
Signed-off-by: Asad Kamal <asad.kamal@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/pm: Use devm_i2c_add_adapter() in the V14_0_2 smu
The I2C init for V14_0_2 uses i2c_add_adapter() and i2c_del_adapter(),
this commit replaces the use of these two functions with
devm_i2c_add_adapter(). Notice that V14_0_2 init initializes multiple
I2C buses in a loop; if something goes wrong, the previous adapters are
removed, and the amdgpu load is interrupted. Since I2C init is required
for the correct load of amdgpu, it is safe to rely on
devm_i2c_add_adapter() to handle any previously initialized I2C adapter.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/pm: Use devm_i2c_add_adapter() in the V13_0_6 smu
The I2C init for V13_0_6 uses i2c_add_adapter() and i2c_del_adapter(),
this commit replaces the use of these two functions with
devm_i2c_add_adapter(). Notice that V13_0_6 init initializes multiple
I2C buses in a loop; if something goes wrong, the previous adapters are
removed, and the amdgpu load is interrupted. Since I2C init is required
for the correct load of amdgpu, it is safe to rely on
devm_i2c_add_adapter() to handle any previously initialized I2C adapter.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/pm: Use devm_i2c_add_adapter() in the V13 smu
The I2C init for SMU_V13 uses i2c_add_adapter() and i2c_del_adapter(),
this commit replaces the use of these two functions with
devm_i2c_add_adapter(). Notice that SMU_V13 init initializes multiple
I2C buses in a loop; if something goes wrong, the previous adapters are
removed, and the amdgpu load is interrupted. Since I2C init is required
for the correct load of amdgpu, it is safe to rely on
devm_i2c_add_adapter() to handle any previously initialized I2C adapter.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/pm: Use devm_i2c_add_adapter() in the Sienna smu
The I2C init for Sienna Cichlid uses i2c_add_adapter() and
i2c_del_adapter(), this commit replaces the use of these two functions
with devm_i2c_add_adapter(). Notice that Sienna Cichlid init initializes
multiple I2C buses in a loop; if something goes wrong, the previous
adapters are removed, and the amdgpu load is interrupted. Since I2C init
is required for the correct load of amdgpu, it is safe to rely on
devm_i2c_add_adapter() to handle any previously initialized I2C adapter.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/pm: Use devm_i2c_add_adapter() in the Navi10 smu
The I2C init for Navi10 uses i2c_add_adapter() and i2c_del_adapter(),
this commit replaces the use of these two functions with
devm_i2c_add_adapter(). Notice that Navi10 init initializes multiple I2C
buses in a loop; if something goes wrong, the previous adapters are
removed, and the amdgpu load is interrupted. Since I2C init is required
for the correct load of amdgpu, it is safe to rely on
devm_i2c_add_adapter() to handle any previously initialized I2C adapter.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/pm: Use devm_i2c_add_adapter() in the Arcturus smu
The I2C init for Arcturus uses i2c_add_adapter() and i2c_del_adapter(),
this commit replaces the use of these two functions with
devm_i2c_add_adapter(). Notice that Arcturus init initializes multiple
I2C buses in a loop; if something goes wrong, the previous adapters are
removed, and the amdgpu load is interrupted. Since I2C init is required
for the correct load of amdgpu, it is safe to rely on
devm_i2c_add_adapter() to handle any previously initialized I2C adapter.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu/amdgpu_i2c: Use devm_i2c_add_adapter instead of i2c_add_adapter
This commit replaces i2c_add_adapter() with devm_i2c_add_adapter() and
removes part of the cleanup logic since the new function handles the i2c
removal.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Use devm_i2c_add_adapter to simplify i2c cleanup logic
This commit replaces the utilization of i2c_add/del_adapter() with
devm_i2c_add_adapter() to reduce the amount of boilerplate. Using
devm_i2c_add_adapter() has the advantage of removing the manual
manipulation of the I2C adapter.
Suggested-by: Robert Beckett <bob.beckett@collabora.com> Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
James Flowers [Sat, 13 Sep 2025 05:19:52 +0000 (22:19 -0700)]
drm/amd/display: Use kmalloc_array() instead of kmalloc()
Documentation/process/deprecated.rst recommends against the use of kmalloc
with dynamic size calculations due to the risk of overflow and smaller
allocation being made than the caller was expecting. This could lead to
buffer overflow in code similar to the memcpy in
amdgpu_dm_plane_add_modifier().
Signed-off-by: James Flowers <bold.zone2373@fastmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 27 Aug 2025 07:28:40 +0000 (09:28 +0200)]
drm/amdgpu: fix userq VM validation v4
That was actually complete nonsense and not validating the BOs
at all. The code just cleared all VM areas were it couldn't grab the
lock for a BO.
Try to fix this. Only compile tested at the moment.
v2: fix fence slot reservation as well as pointed out by Sunil.
also validate PDs, PTs, per VM BOs and update PDEs
v3: grab the status_lock while working with the done list.
v4: rename functions, add some comments, fix waiting for updates to
complete.
v4: rename amdgpu_vm_lock_done_list(), add some more comments
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Sunil Khatri <sunil.khatri@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 27 Aug 2025 11:14:43 +0000 (13:14 +0200)]
drm/amdgpu: reject gang submissions under SRIOV
Gang submission means that the kernel driver guarantees that multiple
submissions are executed on the HW at the same time on different engines.
Background is that those submissions then depend on each other and each
can't finish stand alone.
SRIOV now uses world switch to preempt submissions on the engines to allow
sharing the HW resources between multiple VFs.
The problem is now that the SRIOV world switch can't know about such inter
dependencies and will cause a timeout if it waits for a partially running
gang submission.
To conclude SRIOV and gang submissions are fundamentally incompatible at
the moment. For now just disable them.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd: Drop unnecessary calls to smu_dpm_set_vpe_enable()
smu_hw_init() and smu_hw_fini() call smu_dpm_set_vpe_enable() for
APUs as part of startup and teardown. These calls however are
not necessary because vpe_hw_init()/vpe_hw_fini() will call at
init/fini:
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 6 Jun 2025 12:53:54 +0000 (14:53 +0200)]
drm/amdgpu: revert "Implement new dummy vram manager"
This is should be unnecessary since a VRAM manager isn't mandatory in
the first place.
It could be that we have some missing checks inside AMDGPU or TTM but
those should then be fixed instead of worked around like that.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 5 Sep 2025 12:45:39 +0000 (14:45 +0200)]
drm/amdgpu: add AMDGPU_IDS_FLAGS_GANG_SUBMIT
Add a UAPI flag indicating if gang submit is supported or not.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Mon, 25 Aug 2025 21:56:31 +0000 (23:56 +0200)]
drm/amd/display: Don't use non-registered VUPDATE on DCE 6
The VUPDATE interrupt isn't registered on DCE 6, so don't try
to use that.
This fixes a page flip timeout after sleep/resume on DCE 6.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Mon, 25 Aug 2025 21:56:30 +0000 (23:56 +0200)]
drm/amd/display: Disable VRR on DCE 6
DCE 6 was not advertised as being able to support VRR,
so let's mark it as unsupported for now.
The VRR implementation in amdgpu_dm depends on the VUPDATE
interrupt which is not registered for DCE 6.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Mon, 25 Aug 2025 21:56:29 +0000 (23:56 +0200)]
drm/amd/display: Disable fastboot on DCE 6 too
It already didn't work on DCE 8,
so there is no reason to assume it would on DCE 6.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xi Ruoyao [Mon, 25 Aug 2025 08:52:11 +0000 (16:52 +0800)]
drm/amd/display/dml2: Guard dml21_map_dc_state_into_dml_display_cfg with DC_FP_START
dml21_map_dc_state_into_dml_display_cfg calls (the call is usually
inlined by the compiler) populate_dml21_surface_config_from_plane_state
and populate_dml21_plane_config_from_plane_state which may use FPU. In
a x86-64 build:
Thus it needs to be guarded with DC_FP_START. But we must note that the
current code quality of the in-kernel FPU use in AMD dml2 is very much
problematic: we are actually calling DC_FP_START in dml21_wrapper.c
here, and this translation unit is built with CC_FLAGS_FPU. Strictly
speaking this does not make any sense: with CC_FLAGS_FPU the compiler is
allowed to generate FPU uses anywhere in the translated code, perhaps
out of the DC_FP_START guard. This problematic pattern also occurs in
at least dml2_wrapper.c, dcn35_fpu.c, and dcn351_fpu.c. Thus we really
need a careful audit and refactor for the in-kernel FPU uses, and this
patch is simply whacking a mole. However per the reporter, whacking
this mole is enough to make a 9060XT "just work."
Reported-by: Asiacn <710187964@qq.com> Closes: https://github.com/loongson-community/discussions/issues/102 Tested-by: Asiacn <710187964@qq.com> Signed-off-by: Xi Ruoyao <xry111@xry111.site> Reviewed-by: Huacai Chen <chenhuacai@loongson.cn> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Mon, 25 Aug 2025 21:56:28 +0000 (23:56 +0200)]
drm/amd/display: Keep PLL0 running on DCE 6.0 and 6.4
DC can turn off the display clock when no displays are connected
or when all displays are off, for reference see:
- dce*_validate_bandwidth
DC also assumes that the DP clock is always on and never powers
it down, for reference see:
- dce110_clock_source_power_down
In case of DCE 6.0 and 6.4, PLL0 is the clock source for both
the engine clock and DP clock, for reference see:
- radeon_atom_pick_pll
- atombios_crtc_set_disp_eng_pll
Therefore, PLL0 should be always kept running on DCE 6.0 and 6.4.
This commit achieves that by ensuring that by setting the display
clock to the corresponding value in low power state instead of
zero.
This fixes a page flip timeout on SI with DC which happens when
all connected displays are blanked.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Mon, 25 Aug 2025 21:33:33 +0000 (23:33 +0200)]
drm/amd/display: Fix DVI-D/HDMI adapters
When the EDID has the HDMI bit, we should simply select
the HDMI signal type even on DVI ports.
For reference see, the legacy amdgpu display code:
amdgpu_atombios_encoder_get_encoder_mode
which selects ATOM_ENCODER_MODE_HDMI for the same case.
This commit fixes DVI connectors to work with DVI-D/HDMI
adapters so that they can now produce output over these
connectors for HDMI monitors with higher bandwidth modes.
With this change, even HDMI audio works through DVI.
For testing, I used a CAA-DMDHFD3 DVI-D/HDMI adapter
with the following GPUs:
Tahiti (DCE 6) - DC can now output 4K 30 Hz over DVI
Polaris 10 (DCE 11.2) - DC can now output 4K 60 Hz over DVI
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
James Zhu [Fri, 22 Aug 2025 19:38:01 +0000 (15:38 -0400)]
drm/amdkfd: add function svm_migrate_successful_pages
to get migration pages. dst MIGRATE_PFN_VALID bit and src
MIGRATE_PFN_MIGRATE bit should always be set when migration success.
cpage includes src MIGRATE_PFN_MIGRATE bit set and MIGRATE_PFN_VALID
bit unset pages for both RAM and VRAM when memory is only allocated
without being populated before migration, those ram pages should be
counted as migrated pages and those vram pages should not be counted
as migrated pages. Here migration pages refer to how many vram pages
invloved. Current svm_migrate_unsuccessful_pages only covers the
unsuccessful case that source is on RAM.
So far, we only see two unsuccessful migration cases. Since we
can clearly identify successful migration cases through dst
MIGRATE_PFN_VALID bit and src MIGRATE_PFN_MIGRATE bit within this
prange, also eventually successful migration pages will be used,
so we can use function svm_migrate_successful_pages to replace
function svm_migrate_unsuccessful_pages.
Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Philip Yang<Philip.Yang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
migrate_vma_pages can fail if a CPU thread faults on the same page.
However, the page table is locked and only one of the new pages will
be inserted. The device driver will see that the MIGRATE_PFN_MIGRATE
bit is cleared if it loses the race.
Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Philip Yang <Philip.Yang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shaoyun Liu [Thu, 11 Sep 2025 16:59:00 +0000 (12:59 -0400)]
drm/amd/amdgpu: Fix the mes version that support inv_tlbs
MES pipe0 will do VM invalidation with engine set 5 when assign VMID to a process,
driver will submit inv_tlb package to mes pipe1. It might run into race condition
if both pipes use the same invalidate engine set. From MES version 0x83 it will use
invalidate engine set 6 for pipe1 to fix the issue
Signed-off-by: Shaoyun Liu <shaoyun.liu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Limonciello (AMD) [Mon, 11 Aug 2025 17:00:06 +0000 (12:00 -0500)]
drm/amd: Avoid evicting resources at S5
Normally resources are evicted on dGPUs at suspend or hibernate and
on APUs at hibernate. These steps are unnecessary when using the S4
callbacks to put the system into S5.
Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Kai-Heng Feng <kaihengf@nvidia.com> Cc: Mark Pearson <mpearson-lenovo@squebb.ca> Cc: Denis Benato <benato.denis96@gmail.com> Cc: Merthan Karakaş <m3rthn.k@gmail.com> Tested-by: Eric Naim <dnaim@cachyos.org> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jesse.Zhang [Tue, 5 Aug 2025 04:23:18 +0000 (12:23 +0800)]
drm/amdgpu: Switch user queues to use preempt/restore for eviction
This patch modifies the user queue management to use preempt/restore
operations instead of full map/unmap for queue eviction scenarios where
applicable. The changes include:
1. Introduces new helper functions:
- amdgpu_userqueue_preempt_helper()
- amdgpu_userqueue_restore_helper()
2. Updates queue state management to track PREEMPTED state
3. Modifies eviction handling to use preempt instead of unmap:
- amdgpu_userq_evict_all() now uses preempt_helper
- amdgpu_userq_restore_all() now uses restore_helper
The preempt/restore approach provides better performance during queue
eviction by avoiding the overhead of full queue teardown and setup.
Full map/unmap operations are still used for initial setup/teardown
and system suspend scenarios.
v2: rename amdgpu_userqueue_restore_helper/amdgpu_userqueue_preempt_helper to
amdgpu_userq_restore_helper/amdgpu_userq_preempt_helper for consistency. (Alex)
v3: amdgpu_userq_stop_sched_for_enforce_isolation() and
amdgpu_userq_start_sched_for_enforce_isolation() should use preempt and restore (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: adjust MES API used for suspend and resume
Use the suspend and resume API rather than remove queue
and add queue API. The former just preempts the queue
while the latter remove it from the scheduler completely.
There is no need to do that, we only need preemption
in this case.
V2: replace queue_active with queue state
v3: set the suspend_fence_addr
v4: allocate another per queue buffer for the suspend fence, and set the sequence number.
also wait for the suspend fence. (Alex)
v5: use a wb slot (Alex)
v6: Change the timeout period. For MES, the default timeout is 2100000; /* 2100 ms */ (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following updates:
- Add DSC padding for OVT support
- Setup pixel encoding for YCBCR422
- Fix dml ms order
- Rename header file link.h to link_service.h
- Fix DMUB loading sequence
- Modify link training policy
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com> Acked-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Martin Leung [Wed, 6 Aug 2025 21:40:55 +0000 (17:40 -0400)]
Revert "drm/amd/display: Reduce Stack Usage by moving 'audio_output' into 'stream_res' v4"
This reverts commit 1cf1205ef268 ("drm/amd/display: Reduce Stack Usage by moving 'audio_output' into 'stream_res' v4")
Reason for revert: Causes DP compliance errors
Acked-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Martin Leung <Martin.Leung@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Certain OVT timings require DSC configurations which divide the
horizontal active unevenly across DSC slices
-DSC slices must be even, so padding needs to be added to the active
to make this possible
-The pixel clock of the HW now needs to be increased to accommodate
the extra padded pixels
-To keep the line time the same, the blank of the HW timing needs to
be increased as well
[How]
-Calculate h_active padding, h_total padding, and pixel clock based
off of the original OVT timing and DSC calculations
-Store these values in the pipe and program HW with these modifications
-Added general support for cases where DSC slice config does not evenly
split the horizontal active by fixing some slice width calculations
-Updated PPS calculations for these cases
Reviewed-by: Chris Park <chris.park@amd.com> Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Relja Vojvodic <rvojvodi@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This resolves cases where displays would show no image due to insufficient
DP link bandwidth for the requested RGB mode.
Suggested-by: Mauri Carvalho <mcarvalho3@lenovo.com> Reviewed-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Mario Limonciello <Mario.Limonciello@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Limonciello [Wed, 27 Aug 2025 01:18:22 +0000 (20:18 -0500)]
drm/amd/display: Set up pixel encoding for YCBCR422
[Why]
fill_stream_properties_from_drm_display_mode() will not configure pixel
encoding to YCBCR422 when the DRM color format supports YCBCR422 but not
YCBCR420 or YCBCR4444. Instead it will fallback to RGB.
[How]
Add support for YCBCR422 in pixel encoding mapping.
Suggested-by: Mauri Carvalho <mcarvalho3@lenovo.com> Reviewed-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Mario Limonciello <Mario.Limonciello@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why&how]
small error in order of operations in immediateflipbytes
calculation on dml ms side that can result in dml ms
and mp mismatch immediateflip support for a given pipe
and thus an invalid hw state, correct the order to align
with mp.
Reviewed-by: Leo Chen <leo.chen@amd.com> Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Charlene Liu [Wed, 3 Sep 2025 19:00:22 +0000 (15:00 -0400)]
drm/amd/display: limit one non-related log to dGPU
[Why&How]
some log are for dGPU only.
Added check to limit log.
Reviewed-by: Chris Park <chris.park@amd.com> Signed-off-by: Charlene Liu <Charlene.Liu@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ivan Lipski [Tue, 2 Sep 2025 20:20:09 +0000 (16:20 -0400)]
drm/amd/display: Allow RX6xxx & RX7700 to invoke amdgpu_irq_get/put
[Why&How]
As reported on https://gitlab.freedesktop.org/drm/amd/-/issues/3936,
SMU hang can occur if the interrupts are not enabled appropriately,
causing a vblank timeout.
This patch reverts commit 5009628d8509 ("drm/amd/display: Remove unnecessary
amdgpu_irq_get/put"), but only for RX6xxx & RX7700 GPUs, on which the
issue was observed.
This will re-enable interrupts regardless of whether the user space needed
it or not.
Fixes: 5009628d8509 ("drm/amd/display: Remove unnecessary amdgpu_irq_get/put") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3936 Suggested-by: Sun peng Li <sunpeng.li@amd.com> Reviewed-by: Sun peng Li <sunpeng.li@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Rename header file link.h to link_service.h
[WHY]
Header file name "link.h" collides with system header when dc is
compiled as a user-mode library
[WHAT]
Rename link.h to link_service.h to avoid name collision
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nicholas Kazlauskas [Fri, 8 Aug 2025 14:26:22 +0000 (10:26 -0400)]
drm/amd/display: Fix DMCUB loading sequence for DCN3.2
[Why]
New sequence from HW for reset and firmware reloading has been
provided that aims to stabilize the reload sequence in the case the
firmware is hung or has outstanding requests.
[How]
Update the sequence to remove the DMUIF reset and the redundant
writes in the release.
Reviewed-by: Sreeja Golui <sreeja.golui@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dmytro Laktyushkin [Wed, 11 Jun 2025 20:51:21 +0000 (16:51 -0400)]
drm/amd/display: prepare dml 2.1 for new asic
[Why&How]
prepare dml 2.1 for new asic
Acked-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Currently fallback to low link rate if the link training
fails once on USB4. It may cause the bandwidth couldn't
satisfy the requirement of streams. Modify the policy
to do training retry in the previous few times, only
do fallback at the last time.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com> Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu/gfx11: Add Cleaner Shader Support for GFX11.0.1/11.0.4 GPUs
Enable the cleaner shader for additional GFX11.0.1/11.0.4 series GPUs to
ensure data isolation among GPU tasks. The cleaner shader is tasked with
clearing the Local Data Store (LDS), Vector General Purpose Registers
(VGPRs), and Scalar General Purpose Registers (SGPRs), which helps avoid
data leakage and guarantees the accuracy of computational results.
This update extends cleaner shader support to GFX11.0.1/11.0.4 GPUs,
previously available for GFX11.0.3. It enhances security by clearing GPU
memory between processes and maintains a consistent GPU state across KGD
and KFD workloads.
Cc: Wasee Alam <wasee.alam@amd.com> Cc: Mario Sopena-Novales <mario.novales@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Limonciello [Wed, 10 Sep 2025 18:40:30 +0000 (13:40 -0500)]
drm/amd: Duplicate DC_FEATURE_MASK and DC_DEBUG_MASK enum values into kdoc
[Why]
When kernel documentation is generated the enum values themselves don't
end up in the documentation. This makes browsing them in HTML a lot
less useful.
[How]
Copy DC_DEBUG_MASK and DC_FEATURE_MASK enum values into matching kdoc
comments.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use memset32 instead of open coding it, just because it is
a tiny bit nicer.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Tue, 9 Sep 2025 14:49:35 +0000 (16:49 +0200)]
drm/amdgpu: Fix allocating extra dwords for rings (v2)
Rename extra_dw to extra_bytes and document what it's for.
The value is already used as if it were bytes in vcn_v4_0.c
and in amdgpu_ring_init. Just adjust the dword count in
jpeg_v1_0.c so that it becomes a byte count.
v2:
Rename extra_dw to extra_bytes as discussed during review.
Fixes: c8c1a1d2ef04 ("drm/amdgpu: define and add extra dword for jpeg ring") Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Tue, 9 Sep 2025 14:17:51 +0000 (16:17 +0200)]
drm/amd/pm: Use pm_display_cfg in legacy DPM (v2)
This commit is necessary for DC to function well with chips
that use the legacy power management code, ie. SI and KV.
Communicate display information from DC to the legacy PM code.
Currently DC uses pm_display_cfg to communicate power management
requirements from the display code to the DPM code.
However, the legacy (non-DC) code path used different fields
and therefore could not take into account anything from DC.
Change the legacy display code to fill the same pm_display_cfg
struct as DC and use the same in the legacy DPM code.
To ease review and reduce churn, this commit does not yet
delete the now unneeded code, that is done in the next commit.
v2:
Rebase.
Fix single_display in amdgpu_dpm_pick_power_state.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Tue, 9 Sep 2025 14:17:50 +0000 (16:17 +0200)]
drm/amd/display: Add pixel_clock to amd_pp_display_configuration
This commit adds the pixel_clock field to the display config
struct so that power management (DPM) can use it.
We currently don't have a proper bandwidth calculation on old
GPUs with DCE 6-10 because dce_calcs only supports DCE 11+.
So the power management (DPM) on these GPUs may need to make
ad-hoc decisions for display based on the pixel clock.
Also rename sym_clock to pixel_clock in dm_pp_single_disp_config
to avoid confusion with other code where the sym_clock refers to
the DisplayPort symbol clock.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add mmio_remap bookkeeping to amdgpu_device and introduce
amdgpu_ttm_mmio_remap_bo_init()/fini() to manage a kernel-owned,
one-page (4K) BO in AMDGPU_GEM_DOMAIN_MMIO_REMAP.
Bookkeeping:
- adev->rmmio_remap.bo : kernel-owned singleton BO
The BO is allocated during TTM init when a remap bus address is available
(adev->rmmio_remap.bus_addr) and PAGE_SIZE <= AMDGPU_GPU_PAGE_SIZE (4K),
and freed during TTM fini.
v2:
- Check mmio_remap bus address (adev->rmmio_remap.bus_addr) instead of
rmmio_base. (Alex)
- Skip quietly if PAGE_SIZE > AMDGPU_GPU_PAGE_SIZE or no bus address
(no warn). (Alex)
- Use `amdgpu_bo_create()` (not *_kernel) - Only with this The object
is stored in adev->mmio_remap.bo and will later be exposed to
userspace via a GEM handle. (Christian)
v3:
- Remove obvious comment before amdgpu_ttm_mmio_remap_bo_fini() call.
(Alex)
v4:
- Squash bookkeeping into this patch (Christian)
Suggested-by: Christian König <christian.koenig@amd.com> Suggested-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yang Wang [Tue, 9 Sep 2025 02:10:40 +0000 (10:10 +0800)]
drm/amd/pm: make smu_set_temp_funcs() smu specific for smu v13.0.6
move smu_set_temp_funcs() into smu_v13.0.6 ppt.c file to keep same code
layer in amdgpu_smu.c. (only set_ppt func in amdgpu_smu.c)
Signed-off-by: Yang Wang <kevinyang.wang@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Asad Kamal <asad.kamal@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a one-page TTM range manager for AMDGPU_PL_MMIO_REMAP via
amdgpu_ttm_init_on_chip(). This only registers the placement with TTM;
no BO is allocated in this patch.
The singleton 4K remap BO is created and freed in the following patch.
This split follows to separate heap bring-up from BO allocation.
Cc: Christian König <christian.koenig@amd.com> Suggested-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Srinivasan Shanmugam [Wed, 20 Aug 2025 10:51:16 +0000 (16:21 +0530)]
drm/amdgpu: Implement TTM handling for MMIO_REMAP placement
Implement TTM-level behavior for AMDGPU_PL_MMIO_REMAP so it behaves as a
CPU-visible IO page:
* amdgpu_evict_flags(): mark as unmovable
* amdgpu_res_cpu_visible(): consider CPU-visible
* amdgpu_bo_move(): use null move when src/dst is MMIO_REMAP
* amdgpu_ttm_io_mem_reserve(): program base/is_iomem/caching using
the device's mmio_remap_* metadata
* amdgpu_ttm_io_mem_pfn(): return PFN for the remapped HDP page
* amdgpu_ttm_tt_pde_flags(): set AMDGPU_PTE_SYSTEM for this mem type
v2:
- Drop HDP-specific comment; keep generic remap (Alex).
v3:
- Fix indentation in amdgpu_res_cpu_visible (Christian).
- Use adev->rmmio_remap.bus_addr for MMIO_REMAP bus/PFN calculations
(Alex).
v4:
- Drop unnecessary (resource_size_t) casts in MMIO_REMAP io-mem paths
(Alex)
Cc: Christian König <christian.koenig@amd.com> Suggested-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Remove volatile from amdgpu and amdgpu_ih headers
Remove the unnecessary use of volatile in some of the amdgpu.h and
amdgpu_ih.h headers.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Remove volatile from ring manipulation
None of the pointer operations handled by the ring file requires
volatile, for this reason, this commit removes all occurrences of
volatile associated with rings.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The RLC uses volatile with some pointers that are not directly related
to any of the situations where volatile is advised to be used [1]. For
this reason, this commit removes all the volatile occurrences associated
with RLC.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The CSB buffer manipulation occurs in memory where the BO is mapped
during initialization, and some references to this buffer are handled
with volatile, which is incorrect in this scenario. There are a few
cases where the use of volatile is accepted, but none of them align with
CSB operations. Therefore, this commit removes all the volatile
variables associated with the CSB code.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rodrigo Siqueira [Mon, 25 Aug 2025 00:46:41 +0000 (18:46 -0600)]
drm/amdgpu/vcn: Change amdgpu_vcn_sw_fini return to void
The function amdgpu_vcn_sw_fini() returns an integer, but this number is
always 0. This commit changes the amdgpu_vcn_sw_fini() return to void,
and eliminates all checks to this return across different VCNs.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rodrigo Siqueira [Mon, 25 Aug 2025 00:46:40 +0000 (18:46 -0600)]
drm/amdgpu/vcn: Document IRQ per-instance irq behavior for VCN 4.0.3
When examining the VCN function init, it is common to find a loop that
initializes VCN rings, which uses one IRQ per instance. However, VCN
4.0.3 deviates from this pattern, as it includes a distinct field to
differentiate instances, which results in a slightly different ring
init. This commit makes this difference explicit by using a fixed index
when initializing the ring buffer and also adds a comment.
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prike Liang [Fri, 16 May 2025 08:20:54 +0000 (16:20 +0800)]
drm/amdgpu: validate userq hw unmap status for destroying userq
Before destroying the userq buffer object, it requires validating
the userq HW unmap status and ensuring the userq is unmapped from
hardware. If the user HW unmap failed, then it needs to reset the
queue for reusing.
Signed-off-by: Prike Liang <Prike.Liang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Srinivasan Shanmugam [Wed, 20 Aug 2025 10:47:52 +0000 (16:17 +0530)]
drm/amdgpu: Wire up MMIO_REMAP placement and User-visible strings
Wire up the conversions and strings for the new MMIO_REMAP placement:
* amdgpu_mem_type_to_domain() maps AMDGPU_PL_MMIO_REMAP -> domain
* amdgpu_bo_placement_from_domain() accepts the new domain
* amdgpu_bo_mem_stats_placement() and amdgpu_bo_print_info() report it
* res cursor supports the new placement
* fdinfo prints "mmioremap" for the new placement
Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Srinivasan Shanmugam [Wed, 20 Aug 2025 07:18:50 +0000 (12:48 +0530)]
drm/amdgpu/ttm: Add New AMDGPU_PL_MMIO_REMAP Placement
Introduce a kernel-internal TTM placement type AMDGPU_PL_MMIO_REMAP
for the HDP flush MMIO remap page
Plumbing added:
- amdgpu_res_cursor.{first,next}: treat MMIO_REMAP like DOORBELL
- amdgpu_ttm_io_mem_reserve(): return BAR bus address + offset
for MMIO_REMAP, mark as uncached I/O
- amdgpu_ttm_io_mem_pfn(): PFN from register BAR
- amdgpu_res_cpu_visible(): visible to CPU
- amdgpu_evict_flags()/amdgpu_bo_move(): non-migratable
- amdgpu_ttm_tt_pde_flags(): map as SYSTEM
- amdgpu_bo_mem_stats_placement(): report AMDGPU_PL_MMIO_REMAP
- amdgpu_fdinfo: print “mmioremap” bucket label
Cc: Alex Deucher <alexander.deucher@amd.com> Suggested-by: Christian König <christian.koenig@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Rosca [Mon, 18 Aug 2025 07:18:37 +0000 (09:18 +0200)]
drm/amdgpu/vcn: Allow limiting ctx to instance 0 for AV1 at any time
There is no reason to require this to happen on first submitted IB only.
We need to wait for the queue to be idle, but it can be done at any
time (including when there are multiple video sessions active).
Signed-off-by: David Rosca <david.rosca@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / users / hch / misc.git / log