The initial support for dynamic ftrace trampolines in modules made use
of an indirect branch which loaded its target from the beginning of
a special section (e71a4e1bebaf7 ("arm64: ftrace: add support for far
branches to dynamic ftrace")). Since no instructions were being patched,
no cache maintenance was needed. However, later in be0f272bfc83 ("arm64:
ftrace: emit ftrace-mod.o contents through code") this code was reworked
to output the trampoline instructions directly into the PLT entry but,
unfortunately, the necessary cache maintenance was overlooked.
Add a call to __flush_icache_range() after writing the new trampoline
instructions but before patching in the branch to the trampoline.
ITLB entry modifications must be followed by the isync instruction
before the new entries are possibly used. cpu_reset lacks one isync
between ITLB way 6 initialization and jump to the identity mapping.
Add missing isync to xtensa cpu_reset.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I -thought- I had fixed this entirely, but it looks like that I didn't
test this thoroughly enough as we apparently still make one big mistake
with nv50_msto_atomic_check() - we don't handle the following scenario:
* CRTC #1 has n VCPI allocated to it, is attached to connector DP-4
which is attached to encoder #1. enabled=y active=n
* CRTC #1 is changed from DP-4 to DP-5, causing:
* DP-4 crtc=#1→NULL (VCPI n→0)
* DP-5 crtc=NULL→#1
* CRTC #1 steals encoder #1 back from DP-4 and gives it to DP-5
* CRTC #1 maintains the same mode as before, just with a different
connector
* mode_changed=n connectors_changed=y
(we _SHOULD_ do VCPI 0→n here, but don't)
Once the above scenario is repeated once, we'll attempt freeing VCPI
from the connector that we didn't allocate due to the connectors
changing, but the mode staying the same. Sigh.
Since nv50_msto_atomic_check() has broken a few times now, let's rethink
things a bit to be more careful: limit both VCPI/PBN allocations to
mode_changed || connectors_changed, since neither VCPI or PBN should
ever need to change outside of routing and mode changes.
Changes since v1:
* Fix accidental reversal of clock and bpp arguments in
drm_dp_calc_pbn_mode() - William Lewis
Signed-off-by: Lyude Paul <lyude@redhat.com> Reported-by: Bohdan Milar <bmilar@redhat.com> Tested-by: Bohdan Milar <bmilar@redhat.com> Fixes: 232c9eec417a ("drm/nouveau: Use atomic VCPI helpers for MST")
References: 412e85b60531 ("drm/nouveau: Only release VCPI slots on mode changes") Cc: Lyude Paul <lyude@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@redhat.com> Cc: Jerry Zuo <Jerry.Zuo@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Juston Li <juston.li@intel.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Karol Herbst <karolherbst@gmail.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Cc: <stable@vger.kernel.org> # v5.1+ Acked-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190809005307.18391-1-lyude@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid reducing the frequency of a CPU prematurely, we skip reducing
the frequency if the CPU had been busy recently.
This should not be done when the limits of the policy are changed, for
example due to thermal throttling. We should always get the frequency
within the new limits as soon as possible.
Trying to fix this by using only one flag, i.e. need_freq_update, can
lead to a race condition where the flag gets cleared without forcing us
to change the frequency at least once. And so this patch introduces
another flag to avoid that race condition.
Fixes: ecd288429126 ("cpufreq: schedutil: Don't set next_freq to UINT_MAX") Cc: v4.18+ <stable@vger.kernel.org> # v4.18+ Reported-by: Doug Smythies <dsmythies@telus.net> Tested-by: Doug Smythies <dsmythies@telus.net> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Chinner reported a problem pointing a finger at commit 1c30844d2dfe
("mm: reclaim small amounts of memory when an external fragmentation
event occurs").
and it's worth recording the most relevant parts (colorful language and
typos included).
When running a simple, steady state 4kB file creation test to
simulate extracting tarballs larger than memory full of small
files into the filesystem, I noticed that once memory fills up
the cache balance goes to hell.
The workload is creating one dirty cached inode for every dirty
page, both of which should require a single IO each to clean and
reclaim, and creation of inodes is throttled by the rate at which
dirty writeback runs at (via balance dirty pages). Hence the ingest
rate of new cached inodes and page cache pages is identical and
steady. As a result, memory reclaim should quickly find a steady
balance between page cache and inode caches.
The moment memory fills, the page cache is reclaimed at a much
faster rate than the inode cache, and evidence suggests that
the inode cache shrinker is not being called when large batches
of pages are being reclaimed. In roughly the same time period
that it takes to fill memory with 50% pages and 50% slab caches,
memory reclaim reduces the page cache down to just dirty pages
and slab caches fill the entirety of memory.
The LRU is largely full of dirty pages, and we're getting spikes
of random writeback from memory reclaim so it's all going to shit.
Behaviour never recovers, the page cache remains pinned at just
dirty pages, and nothing I could tune would make any difference.
vfs_cache_pressure makes no difference - I would set it so high
it should trim the entire inode caches in a single pass, yet it
didn't do anything. It was clear from tracing and live telemetry
that the shrinkers were pretty much not running except when
there was absolutely no memory free at all, and then they did
the minimum necessary to free memory to make progress.
So I went looking at the code, trying to find places where pages
got reclaimed and the shrinkers weren't called. There's only one
- kswapd doing boosted reclaim as per commit 1c30844d2dfe ("mm:
reclaim small amounts of memory when an external fragmentation
event occurs").
The watermark boosting introduced by the commit is triggered in response
to an allocation "fragmentation event". The boosting was not intended
to target THP specifically and triggers even if THP is disabled.
However, with Dave's perfectly reasonable workload, fragmentation events
can be very common given the ratio of slab to page cache allocations so
boosting remains active for long periods of time.
As high-order allocations might use compaction and compaction cannot
move slab pages the decision was made in the commit to special-case
kswapd when watermarks are boosted -- kswapd avoids reclaiming slab as
reclaiming slab does not directly help compaction.
As Dave notes, this decision means that slab can be artificially
protected for long periods of time and messes up the balance with slab
and page caches.
Removing the special casing can still indirectly help avoid
fragmentation by avoiding fragmentation-causing events due to slab
allocation as pages from a slab pageblock will have some slab objects
freed. Furthermore, with the special casing, reclaim behaviour is
unpredictable as kswapd sometimes examines slab and sometimes does not
in a manner that is tricky to tune or analyse.
This patch removes the special casing. The downside is that this is not
a universal performance win. Some benchmarks that depend on the
residency of data when rereading metadata may see a regression when slab
reclaim is restored to its original behaviour. Similarly, some
benchmarks that only read-once or write-once may perform better when
page reclaim is too aggressive. The primary upside is that slab
shrinker is less surprising (arguably more sane but that's a matter of
opinion), behaves consistently regardless of the fragmentation state of
the system and properly obeys VM sysctls.
A fsmark benchmark configuration was constructed similar to what Dave
reported and is codified by the mmtest configuration
config-io-fsmark-small-file-stream. It was evaluated on a 1-socket
machine to avoid dealing with NUMA-related issues and the timing of
reclaim. The storage was an SSD Samsung Evo and a fresh trimmed XFS
filesystem was used for the test data.
This is not an exact replication of Dave's setup. The configuration
scales its parameters depending on the memory size of the SUT to behave
similarly across machines. The parameters mean the first sample
reported by fs_mark is using 50% of RAM which will barely be throttled
and look like a big outlier. Dave used fake NUMA to have multiple
kswapd instances which I didn't replicate. Finally, the number of
iterations differ from Dave's test as the target disk was not large
enough. While not identical, it should be representative.
5.3.0-rc3 5.3.0-rc3
vanillashrinker-v1r1
Duration User 501.82 497.29
Duration System 4401.44 4424.08
Duration Elapsed 8124.76 8358.05
This is showing a slight skew for the max result representing a large
outlier for the 1st, 2nd and 3rd quartile are similar indicating that
the bulk of the results show little difference. Note that an earlier
version of the fsmark configuration showed a regression but that
included more samples taken while memory was still filling.
Note that the elapsed time is higher. Part of this is that the
configuration included time to delete all the test files when the test
completes -- the test automation handles the possibility of testing
fsmark with multiple thread counts. Without the patch, many of these
objects would be memory resident which is part of what the patch is
addressing.
There are other important observations that justify the patch.
1. With the vanilla kernel, the number of dirty pages in the system is
very low for much of the test. With this patch, dirty pages is
generally kept at 10% which matches vm.dirty_background_ratio which
is normal expected historical behaviour.
2. With the vanilla kernel, the ratio of Slab/Pagecache is close to
0.95 for much of the test i.e. Slab is being left alone and
dominating memory consumption. With the patch applied, the ratio
varies between 0.35 and 0.45 with the bulk of the measured ratios
roughly half way between those values. This is a different balance to
what Dave reported but it was at least consistent.
3. Slabs are scanned throughout the entire test with the patch applied.
The vanille kernel has periods with no scan activity and then
relatively massive spikes.
4. Without the patch, kswapd scan rates are very variable. With the
patch, the scan rates remain quite steady.
4. Overall vmstats are closer to normal expectations
o Vanilla kernel is hitting direct reclaim more frequently,
not very much in absolute terms but the fact the patch
reduces it is interesting
o "Page reclaim immediate" in the vanilla kernel indicates
dirty pages are being encountered at the tail of the LRU.
This is generally bad and means in this case that the LRU
is not long enough for dirty pages to be cleaned by the
background flush in time. This is much reduced by the
patch.
o With the patch, kswapd is reclaiming 10 times more slab
pages than with the vanilla kernel. This is indicative
of the watermark boosting over-protecting slab
A more complete set of tests were run that were part of the basis for
introducing boosting and while there are some differences, they are well
within tolerances.
Bottom line, the special casing kswapd to avoid slab behaviour is
unpredictable and can lead to abnormal results for normal workloads.
This patch restores the expected behaviour that slab and page cache is
balanced consistently for a workload with a steady allocation ratio of
slab/pagecache pages. It also means that if there are workloads that
favour the preservation of slab over pagecache that it can be tuned via
vm.vfs_cache_pressure where as the vanilla kernel effectively ignores
the parameter when boosting is active.
Link: http://lkml.kernel.org/r/20190808182946.GM2739@techsingularity.net Fixes: 1c30844d2dfe ("mm: reclaim small amounts of memory when an external fragmentation event occurs") Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reviewed-by: Dave Chinner <dchinner@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> [5.0+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when checking to see if accessing n bytes starting at address
"ptr" will cause a wraparound in the memory addresses, the check in
check_bogus_address() adds an extra byte, which is incorrect, as the
range of addresses that will be accessed is [ptr, ptr + (n - 1)].
This can lead to incorrectly detecting a wraparound in the memory
address, when trying to read 4 KB from memory that is mapped to the the
last possible page in the virtual address space, when in fact, accessing
that range of memory would not cause a wraparound to occur.
Use the memory range that will actually be accessed when considering if
accessing a certain amount of bytes will cause the memory address to
wrap around.
Link: http://lkml.kernel.org/r/1564509253-23287-1-git-send-email-isaacm@codeaurora.org Fixes: f5509cc18daa ("mm: Hardened usercopy") Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org> Co-developed-by: Prasad Sodagudi <psodagud@codeaurora.org> Reviewed-by: William Kucharski <william.kucharski@oracle.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Trilok Soni <tsoni@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is sent to report an use after free in mem_cgroup_iter()
after merging commit be2657752e9e ("mm: memcg: fix use after free in
mem_cgroup_iter()").
I work with android kernel tree (4.9 & 4.14), and commit be2657752e9e
("mm: memcg: fix use after free in mem_cgroup_iter()") has been merged
to the trees. However, I can still observe use after free issues
addressed in the commit be2657752e9e. (on low-end devices, a few times
this month)
In the reclaim path, try_to_free_pages() does not setup
sc.target_mem_cgroup and sc is passed to do_try_to_free_pages(), ...,
shrink_node().
In mem_cgroup_iter(), root is set to root_mem_cgroup because
sc->target_mem_cgroup is NULL. It is possible to assign a memcg to
root_mem_cgroup.nodeinfo.iter in mem_cgroup_iter().
My device uses memcg non-hierarchical mode. When we release a memcg:
invalidate_reclaim_iterators() reaches only dead_memcg and its parents.
If non-hierarchical mode is used, invalidate_reclaim_iterators() never
reaches root_mem_cgroup.
The constraint from the zpool use of z3fold_destroy_pool() is there are
no outstanding handles to memory (so no active allocations), but it is
possible for there to be outstanding work on either of the two wqs in
the pool.
Calling z3fold_deregister_migration() before the workqueues are drained
means that there can be allocated pages referencing a freed inode,
causing any thread in compaction to be able to trip over the bad pointer
in PageMovable().
Link: http://lkml.kernel.org/r/20190726224810.79660-2-henryburns@google.com Fixes: 1f862989b04a ("mm/z3fold.c: support page migration") Signed-off-by: Henry Burns <henryburns@google.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Reviewed-by: Jonathan Adams <jwadams@google.com> Cc: Vitaly Vul <vitaly.vul@sony.com> Cc: Vitaly Wool <vitalywool@gmail.com> Cc: David Howells <dhowells@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Henry Burns <henrywolfeburns@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The constraint from the zpool use of z3fold_destroy_pool() is there are
no outstanding handles to memory (so no active allocations), but it is
possible for there to be outstanding work on either of the two wqs in
the pool.
If there is work queued on pool->compact_workqueue when it is called,
z3fold_destroy_pool() will do:
The setsockopt() would allocate compound pages (16 pages in this test)
for packet tx ring, then the mmap() would call packet_mmap() to map the
pages into the user address space specified by the mmap() call.
When calling mbind(), it would scan the vma to queue the pages for
migration to the new node. It would split any huge page since 4.9
doesn't support THP migration, however, the packet tx ring compound
pages are not THP and even not movable. So, the above bug is triggered.
However, the later kernel is not hit by this issue due to commit d44d363f6578 ("mm: don't assume anonymous pages have SwapBacked flag"),
which just removes the PageSwapBacked check for a different reason.
But, there is a deeper issue. According to the semantic of mbind(), it
should return -EIO if MPOL_MF_MOVE or MPOL_MF_MOVE_ALL was specified and
MPOL_MF_STRICT was also specified, but the kernel was unable to move all
existing pages in the range. The tx ring of the packet socket is
definitely not movable, however, mbind() returns success for this case.
Although the most socket file associates with non-movable pages, but XDP
may have movable pages from gup. So, it sounds not fine to just check
the underlying file type of vma in vma_migratable().
Change migrate_page_add() to check if the page is movable or not, if it
is unmovable, just return -EIO. But do not abort pte walk immediately,
since there may be pages off LRU temporarily. We should migrate other
pages if MPOL_MF_MOVE* is specified. Set has_unmovable flag if some
paged could not be not moved, then return -EIO for mbind() eventually.
With this change the above test would return -EIO as expected.
When both MPOL_MF_MOVE* and MPOL_MF_STRICT was specified, mbind() should
try best to migrate misplaced pages, if some of the pages could not be
migrated, then return -EIO.
There are three different sub-cases:
1. vma is not migratable
2. vma is migratable, but there are unmovable pages
3. vma is migratable, pages are movable, but migrate_pages() fails
If #1 happens, kernel would just abort immediately, then return -EIO,
after a7f40cfe3b7a ("mm: mempolicy: make mbind() return -EIO when
MPOL_MF_STRICT is specified").
If #3 happens, kernel would set policy and migrate pages with
best-effort, but won't rollback the migrated pages and reset the policy
back.
Before that commit, they behaves in the same way. It'd better to keep
their behavior consistent. But, rolling back the migrated pages and
resetting the policy back sounds not feasible, so just make #1 behave as
same as #3.
Userspace will know that not everything was successfully migrated (via
-EIO), and can take whatever steps it deems necessary - attempt
rollback, determine which exact page(s) are violating the policy, etc.
Make queue_pages_range() return 1 to indicate there are unmovable pages
or vma is not migratable.
The #2 is not handled correctly in the current kernel, the following
patch will fix it.
When migrating an anonymous private page to a ZONE_DEVICE private page,
the source page->mapping and page->index fields are copied to the
destination ZONE_DEVICE struct page and the page_mapcount() is
increased. This is so rmap_walk() can be used to unmap and migrate the
page back to system memory.
However, try_to_unmap_one() computes the subpage pointer from a swap pte
which computes an invalid page pointer and a kernel panic results such
as:
If you use lseek or similar (e.g. pread) to access a location in a
seq_file file that is within a record, rather than at a record boundary,
then the first read will return the remainder of the record, and the
second read will return the whole of that same record (instead of the
next record). When seeking to a record boundary, the next record is
correctly returned.
This bug was introduced by a recent patch (identified below). Before
that patch, seq_read() would increment m->index when the last of the
buffer was returned (m->count == 0). After that patch, we rely on
->next to increment m->index after filling the buffer - but there was
one place where that didn't happen.
Link: https://lkml.kernel.org/lkml/877e7xl029.fsf@notabene.neil.brown.name/ Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code and interface") Signed-off-by: NeilBrown <neilb@suse.com> Reported-by: Sergei Turchanov <turchanov@farpost.com> Tested-by: Sergei Turchanov <turchanov@farpost.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Markus Elfring <Markus.Elfring@web.de> Cc: <stable@vger.kernel.org> [4.19+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c78719203fc6 ("KEYS: trusted: allow trusted.ko to initialize w/o a
TPM") allows the trusted module to be loaded even if a TPM is not found, to
avoid module dependency problems.
However, trusted module initialization can still fail if the TPM is
inactive or deactivated. tpm_get_random() returns an error.
This patch removes the call to tpm_get_random() and instead extends the PCR
specified by the user with zeros. The security of this alternative is
equivalent to the previous one, as either option prevents with a PCR update
unsealing and misuse of sealed data by a user space process.
Even if a PCR is extended with zeros, instead of random data, it is still
computationally infeasible to find a value as input for a new PCR extend
operation, to obtain again the PCR value that would allow unsealing.
We erroneously added a check for FW API version 41 before sending
GEO_TX_POWER_LIMIT, but this was already implemented in version 38.
Additionally, it was cherry-picked to older versions, namely 17, 26
and 29, so check for those as well.
Cc: stable@vger.kernel.org Fixes: eca1e56ceedd ("iwlwifi: mvm: don't send GEO_TX_POWER_LIMIT to old firmwares") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firmware versions before 41 don't support the GEO_TX_POWER_LIMIT
command, and sending it to the firmware will cause a firmware crash.
We allow this via debugfs, so we need to return an error value in case
it's not supported.
This had already been fixed during init, when we send the command if
the ACPI WGDS table is present. Fix it also for the other,
userspace-triggered case.
Accessing the hdr of an skb that was consumed already isn't
a good idea.
First ask if the skb is a QoS packet, then keep that data
on stack, and then consume the skb.
This was spotted by KASAN.
The index for the elements of the ACPI object we dereference
was static. This means that if we called the function twice
we wouldn't start from 3 again, but rather from the latest
index we reached in the previous call.
This was dutifully reported by KASAN.
Fix this.
Cc: stable@vger.kernel.org Fixes: 6996490501ed ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to remember how to unmap a memory (as single or
as page), we maintain a bit per Transmit Buffer (TBs) in
the meta data (structure iwl_cmd_meta).
We maintain a bitmap: 1 bit per TB.
If the TB is set, we will free the memory as a page.
This bitmap was never cleared. Fix this.
Cc: stable@vger.kernel.org Fixes: 3cd1980b0cdf ("iwlwifi: pcie: introduce new tfd and tb formats") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant
vendor IEs") adjusted the ieee_types_vendor_header struct, which
inadvertently messed up the offsets used in
mwifiex_is_wpa_oui_present(). Add that offset back in, mirroring
mwifiex_is_rsn_oui_present().
As it stands, commit 63d7ef36103d breaks compatibility with WPA (not
WPA2) 802.11n networks, since we hit the "info: Disable 11n if AES is
not supported by AP" case in mwifiex_is_network_compatible().
Fixes: 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant vendor IEs") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit commit 328e56647944 ("KVM: arm/arm64: vgic: Defer
touching GICH_VMCR to vcpu_load/put"), we leave ICH_VMCR_EL2 (or
its GICv2 equivalent) loaded as long as we can, only syncing it
back when we're scheduled out.
There is a small snag with that though: kvm_vgic_vcpu_pending_irq(),
which is indirectly called from kvm_vcpu_check_block(), needs to
evaluate the guest's view of ICC_PMR_EL1. At the point were we
call kvm_vcpu_check_block(), the vcpu is still loaded, and whatever
changes to PMR is not visible in memory until we do a vcpu_put().
Things go really south if the guest does the following:
mov x0, #0 // or any small value masking interrupts
msr ICC_PMR_EL1, x0
[vcpu preempted, then rescheduled, VMCR sampled]
mov x0, #ff // allow all interrupts
msr ICC_PMR_EL1, x0
wfi // traps to EL2, so samping of VMCR
[interrupt arrives just after WFI]
Here, the hypervisor's view of PMR is zero, while the guest has enabled
its interrupts. kvm_vgic_vcpu_pending_irq() will then say that no
interrupts are pending (despite an interrupt being received) and we'll
block for no reason. If the guest doesn't have a periodic interrupt
firing once it has blocked, it will stay there forever.
To avoid this unfortuante situation, let's resync VMCR from
kvm_arch_vcpu_blocking(), ensuring that a following kvm_vcpu_check_block()
will observe the latest value of PMR.
This has been found by booting an arm64 Linux guest with the pseudo NMI
feature, and thus using interrupt priorities to mask interrupts instead
of the usual PSTATE masking.
After commit d73eb57b80b (KVM: Boost vCPUs that are delivering interrupts), a
five years old bug is exposed. Running ebizzy benchmark in three 80 vCPUs VMs
on one 80 pCPUs Skylake server, a lot of rcu_sched stall warning splatting
in the VMs after stress testing:
swait_active() sustains to be true before finish_swait() is called in
kvm_vcpu_block(), voluntarily preempted vCPUs are taken into account
by kvm_vcpu_on_spin() loop greatly increases the probability condition
kvm_arch_vcpu_runnable(vcpu) is checked and can be true, when APICv
is enabled the yield-candidate vCPU's VMCS RVI field leaks(by
vmx_sync_pir_to_irr()) into spinning-on-a-taken-lock vCPU's current
VMCS.
This patch fixes it by checking conservatively a subset of events.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Marc Zyngier <Marc.Zyngier@arm.com> Cc: stable@vger.kernel.org Fixes: 98f4a1467 (KVM: add kvm_arch_vcpu_runnable() test to kvm_vcpu_on_spin() loop) Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that we always check the return value of update_open_stateid()
so that we can retry if the update of local state failed. This fixes
infinite looping on state recovery.
Once we clear the NFS_DELEGATED_STATE flag, we're telling
nfs_delegation_claim_opens() that we're done recovering all open state
for that stateid, so we really need to ensure that we test for all
open modes that are currently cached and recover them before exiting
nfs4_open_delegation_recall().
We had a report of a server which did not do a DFS referral
because the session setup Capabilities field was set to 0
(unlike negotiate protocol where we set CAP_DFS). Better to
send it session setup in the capabilities as well (this also
more closely matches Windows client behavior).
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we skip SMB2_TREE_CONNECT command when checking during
reconnect because Tree Connect happens when establishing
an SMB session. For SMB 3.0 protocol version the code also calls
validate negotiate which results in SMB2_IOCL command being sent
over the wire. This may deadlock on trying to acquire a mutex when
checking for reconnect. Fix this by skipping SMB2_IOCL command
when doing the reconnect check.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"As of now dax_layout_busy_page() calls unmap_mapping_range() with last
argument as 1, which says even unmap cow pages. I am wondering who needs
to get rid of cow pages as well.
I noticed one interesting side affect of this. I mount xfs with -o dax and
mmaped a file with MAP_PRIVATE and wrote some data to a page which created
cow page. Then I called fallocate() on that file to zero a page of file.
fallocate() called dax_layout_busy_page() which unmapped cow pages as well
and then I tried to read back the data I wrote and what I get is old
data from persistent memory. I lost the data I had written. This
read basically resulted in new fault and read back the data from
persistent memory.
This sounds wrong. Are there any users which need to unmap cow pages
as well? If not, I am proposing changing it to not unmap cow pages.
I noticed this while while writing virtio_fs code where when I tried
to reclaim a memory range and that corrupted the executable and I
was running from virtio-fs and program got segment violation."
Dan:
"In fact the unmap_mapping_range() in this path is only to synchronize
against get_user_pages_fast() and force it to call back into the
filesystem to re-establish the mapping. COW pages should be left
untouched by dax_layout_busy_page()."
Cc: <stable@vger.kernel.org> Fixes: 5fac7408d828 ("mm, fs, dax: handle layout changes to pinned dax mappings") Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20190802192956.GA3032@redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a very similar spirit to commit c470bdc1aaf3 ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()
wlan0: invalid CW_min/CW_max: 0/0
and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.
Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().
A long-time problem on the recent AMD chip (X370, X470, B450, etc with
PCI ID 1022:1457) with Realtek codecs is the crackled or distorted
sound for capture streams, as well as occasional playback hiccups.
After lengthy debugging sessions, the workarounds we've found are like
the following:
- Set up the proper driver caps for this controller, similar as the
other AMD controller.
- Correct the DMA position reporting with the fixed FIFO size, which
is similar like as workaround used for VIA chip set.
- Even after the position correction, PulseAudio still shows
mysterious stalls of playback streams when a capture is triggered in
timer-scheduled mode. Since we have no clear way to eliminate the
stall, pass the BATCH PCM flag for PA to suppress the tsched mode as
a temporary workaround.
This patch implements the workarounds. For the driver caps, it
defines a new preset, AXZ_DCAPS_PRESET_AMD_SB. It enables the FIFO-
corrected position reporting (corresponding to the new position_fix=6)
and enforces the SNDRV_PCM_INFO_BATCH flag.
Note that the current implementation is merely a workaround.
Hopefully we'll find a better alternative in future, especially about
removing the BATCH flag hack again.
The commit bfcba288b97f ("ALSA - hda: Add support for link audio time
reporting") introduced the conditional PCM hw info setup, but it
overwrites the global azx_pcm_hw object. This will cause a problem if
any other HD-audio controller, as it'll inherit the same bit flag
although another controller doesn't support that feature.
Fix the bug by setting the PCM hw info flag locally.
Fixes: bfcba288b97f ("ALSA - hda: Add support for link audio time reporting") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In hiface_pcm_init(), 'rt' is firstly allocated through kzalloc(). Later
on, hiface_pcm_init_urb() is invoked to initialize 'rt->out_urbs[i]'. In
hiface_pcm_init_urb(), 'rt->out_urbs[i].buffer' is allocated through
kzalloc(). However, if hiface_pcm_init_urb() fails, both 'rt' and
'rt->out_urbs[i].buffer' are not deallocated, leading to memory leak bugs.
Also, 'rt->out_urbs[i].buffer' is not deallocated if snd_pcm_new() fails.
To fix the above issues, free 'rt' and 'rt->out_urbs[i].buffer'.
In iso_packets_buffer_init(), 'b->packets' is allocated through
kmalloc_array(). Then, the aligned packet size is checked. If it is
larger than PAGE_SIZE, -EINVAL will be returned to indicate the error.
However, the allocated 'b->packets' is not deallocated on this path,
leading to a memory leak.
To fix the above issue, free 'b->packets' before returning the error code.
According to Bspec clock divisor registers in GeminiLake
should be initialized by shifting 1(<<) to amount of correspondent
divisor. While i915 was writing all this time that value as is.
Surprisingly that it by accident worked, until we met some issues
with Microtech Etab.
v2: Added Fixes tag and cc
v3: Added stable to cc as well.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108826 Fixes: bcc657004841 ("drm/i915/glk: Program txesc clock divider for GLK") Cc: Deepak M <m.deepak@intel.com> Cc: Madhav Chauhan <madhav.chauhan@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: stable@vger.kernel.org Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190712081938.14185-1-stanislav.lisovskiy@intel.com
(cherry picked from commit ce52ad5dd52cfaf3398058384e0ff94134bbd89c) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to detect if in4 is present is wrong; if in4 is not present,
the in4_input sysfs attribute is still present.
In detail:
- Ihen RTD3_MD=11 (VSEN3 present), everything is as expected (no bug).
- If we have RTD3_MD!=11 (no VSEN3), we unexpectedly have a in4_input
file under /sys and the "sensors" command displays in4_input.
But as expected, we have no in4_min, in4_max, in4_alarm, in4_beep.
Fix is_visible function to detect and report in4_input visibility
as expected.
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com Fixes: f14e22435a27 ("net: can: peak_usb: Do not do dma on the stack") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8c5fbf1a7231 ("KVM/nSVM: Use the new mapping API for mapping guest
memory") broke nested SVM completely: kvm_vcpu_map()'s second parameter is
GFN so vmcb_gpa needs to be converted with gpa_to_gfn(), not the other way
around.
Fixes: 8c5fbf1a7231 ("KVM/nSVM: Use the new mapping API for mapping guest memory") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In snd_usb_get_audioformat_uac3(), a structure for channel maps 'chmap' is
allocated through kzalloc() before the execution goto 'found_clock'.
However, this structure is not deallocated if the memory allocation for
'pd' fails, leading to a memory leak bug.
To fix the above issue, free 'fp->chmap' before returning NULL.
Valve reported a kernel crash on Ubuntu 18.04 when disconnecting a DS4
gamepad while rumble is enabled. This issue is reproducible with a
frequency of 1 in 3 times in the game Borderlands 2 when using an
automatic weapon, which triggers many rumble operations.
We found the issue to be a race condition between sony_remove and the
final device destruction by the HID / input system. The problem was
that sony_remove didn't clean some of its work_item state in
"struct sony_sc". After sony_remove work, the corresponding evdev
node was around for sufficient time for applications to still queue
rumble work after "sony_remove".
On pre-4.19 kernels the race condition caused a kernel crash due to a
NULL-pointer dereference as "sc->output_report_dmabuf" got freed during
sony_remove. On newer kernels this crash doesn't happen due the buffer
now being allocated using devm_kzalloc. However we can still queue work,
while the driver is an undefined state.
This patch fixes the described problem, by guarding the work_item
"state_worker" with an initialized variable, which we are setting back
to 0 on cleanup.
On s390 ZONE_DMA is up to 2G, i.e. ARCH_ZONE_DMA_BITS should be 31 bits.
The current value is 24 and makes __dma_direct_alloc_pages() take a
wrong turn first (but __dma_direct_alloc_pages() recovers then).
Let's correct ARCH_ZONE_DMA_BITS value and avoid wrong turns.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Reported-by: Petr Tesarik <ptesarik@suse.cz> Fixes: c61e9637340e ("dma-direct: add support for allocation from ZONE_DMA and ZONE_DMA32") Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some hardware PMU drivers will override perf_event.cpu inside their
event_init callback. This causes a lockdep splat when initialized through
the kernel API:
WARNING: CPU: 0 PID: 250 at kernel/events/core.c:2917 ctx_sched_out+0x78/0x208
pc : ctx_sched_out+0x78/0x208
Call trace:
ctx_sched_out+0x78/0x208
__perf_install_in_context+0x160/0x248
remote_function+0x58/0x68
generic_exec_single+0x100/0x180
smp_call_function_single+0x174/0x1b8
perf_install_in_context+0x178/0x188
perf_event_create_kernel_counter+0x118/0x160
Fix this by calling perf_install_in_context with event->cpu, just like
perf_event_open
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Frank Li <Frank.li@nxp.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Link: https://lkml.kernel.org/r/c4ebe0503623066896d7046def4d6b1e06e0eb2e.1563972056.git.leonard.crestez@nxp.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Intel SDM states that bit 13 of Icelake's MSR_OFFCORE_RSP_x
register is valid, and used for counting hardware generated prefetches
of L3 cache. Update the bitmask to allow bit 13.
Before:
$ perf stat -e cpu/event=0xb7,umask=0x1,config1=0x1bfff/u sleep 3
Performance counter stats for 'sleep 3':
<not supported> cpu/event=0xb7,umask=0x1,config1=0x1bfff/u
After:
$ perf stat -e cpu/event=0xb7,umask=0x1,config1=0x1bfff/u sleep 3
Performance counter stats for 'sleep 3':
9,293 cpu/event=0xb7,umask=0x1,config1=0x1bfff/u
Signed-off-by: Yunying Sun <yunying.sun@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: acme@kernel.org Cc: alexander.shishkin@linux.intel.com Cc: bp@alien8.de Cc: hpa@zytor.com Cc: jolsa@redhat.com Cc: namhyung@kernel.org Link: https://lkml.kernel.org/r/20190724082932.12833-1-yunying.sun@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In test_firmware_init(), the buffer pointed to by the global pointer
'test_fw_config' is allocated through kzalloc(). Then, the buffer is
initialized in __test_firmware_config_init(). In the case that the
initialization fails, the following execution in test_firmware_init() needs
to be terminated with an error code returned to indicate this failure.
However, the allocated buffer is not freed on this execution path, leading
to a memory leak bug.
To fix the above issue, free the allocated buffer before returning from
test_firmware_init().
Retrying immediately after we've received a 'transitioning' sense code is
pretty much pointless, we should always use a delay before retrying. So
ensure the default delay is applied before retrying.
Signed-off-by: Hannes Reinecke <hare@suse.com> Tested-by: Zhangguanghui <zhang.guanghui@h3c.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is tripped as a result of irqs being disabled during the call to
dma_free_coherent() by ibmvfc_free_event_pool(). At this point in the code path
we have quiesced the adapter and its overly paranoid anyways to be holding the
host lock.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While loading fw crashdump in function fw_crash_buffer_show(), left bytes
in one dma chunk was not checked, if copying size over it, overflow access
will cause kernel panic.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building a multiplatform kernel that includes armv4 support,
the default target CPU does not support the blx instruction,
which leads to a build failure:
arch/arm/mach-davinci/sleep.S: Assembler messages:
arch/arm/mach-davinci/sleep.S:56: Error: selected processor does not support `blx ip' in ARM mode
Add a .arch statement in the sources to make this file build.
When freeing the subsystem after finding another match with
__nvme_find_get_subsystem(), use put_device() instead of
__nvme_release_subsystem() which calls kfree() directly.
Per the documentation, put_device() should always be used
after device_initialization() is called. Otherwise, leaks
like the one below which was detected by kmemleak may occur.
Once the call of __nvme_release_subsystem() is removed it no
longer makes sense to keep the helper, so fold it back
into nvme_release_subsystem().
There are no firmware updates available from the vendor, unfortunately.
Applying the NVME_QUIRK_IGNORE_DEV_SUBNQN quirk for these SSDs resolves
the issue, and they all work after this patch:
When perf_add_probe_events() we call cleanup_perf_probe_events() for the
pev pointer it receives, then, as part of handling this failure the main
'perf probe' goes on and calls cleanup_params() and that will again call
cleanup_perf_probe_events()for the same pointer, so just set nevents to
zero when handling the failure of perf_add_probe_events() to avoid the
double free.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-x8qgma4g813z96dvtw9w219q@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix decompression failure found during the loading of compressed trace
collected on larger scale systems (>48 cores).
The error happened due to lack of decompression space for a mmaped
buffer data chunk split across adjacent PERF_RECORD_COMPRESSED records.
$ perf report -i bt.16384.data --stats
failed to decompress (B): 63869 -> 0 : Destination buffer is too small
user stack dump failure
Can't parse sample, err = -14
0x2637e436 [0x4080]: failed to process type: 9
Error:
failed to process sample
$ perf test 71
71: Zstd perf.data compression/decompression : Ok
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/4d839e1b-9c48-89c4-9702-a12217420611@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Numfor Mbiziwo-Tiapo reported segfault on stat of event group in repeat
mode:
# perf stat -e '{cycles,instructions}' -r 10 ls
It's caused by memory corruption due to not cleaned evsel's id array and
index, which needs to be rebuilt in every stat iteration. Currently the
ids index grows, while the array (which is also not freed) has the same
size.
Fixing this by releasing id array and zeroing ids index in
perf_evsel__close function.
We also need to keep the evsel_list alive for stat record (which is
disabled in repeat mode).
Reported-by: Numfor Mbiziwo-Tiapo <nums@google.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Drayton <mbd@fb.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/r/20190715142121.GC6032@krava Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After Song Liu's segfault fix for pipe mode, Arnaldo reported following
error:
# perf record -o - | perf script
0x514 [0x1ac]: failed to process type: 80
It's caused by wrong buffer size setup in feature processing, which
makes cpu topology feature fail, because it's using buffer size to
recognize its header version.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Carrillo-Cisneros <davidcc@google.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Fixes: e9def1b2e74e ("perf tools: Add feature header record to pipe-mode") Link: http://lkml.kernel.org/r/20190715140426.32509-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Draining makes little sense in the situation of hardware overrun, as the
hardware will have consumed all its available samples. Additionally,
draining whilst the stream is paused would presumably get stuck as no
data is being consumed on the DSP side.
Partial drain and next track are intended for gapless playback and
don't really have an obvious interpretation for a capture stream, so
makes sense to not allow those operations on capture streams.
Currently, whilst in SNDRV_PCM_STATE_OPEN it is possible to call
snd_compr_stop, snd_compr_drain and snd_compr_partial_drain, which
allow a transition to SNDRV_PCM_STATE_SETUP. The stream should
only be able to move to the setup state once it has received a
SNDRV_COMPRESS_SET_PARAMS ioctl. Fix this issue by not allowing
those ioctls whilst in the open state.
A previous fix to the stop handling on compressed capture streams causes
some knock on issues. The previous fix updated snd_compr_drain_notify to
set the state back to PREPARED for capture streams. This causes some
issues however as the handling for snd_compr_poll differs between the
two states and some user-space applications were relying on the poll
failing after the stream had been stopped.
To correct this regression whilst still fixing the original problem the
patch was addressing, update the capture handling to skip the PREPARED
state rather than skipping the SETUP state as it has done until now.
If the device driver were to send out a full queue's worth of SBALs,
current code would end up discovering the last of those SBALs as PRIMED
and erroneously skip the SIGA-w. This immediately stalls the queue.
Add a check to not attempt fast-requeue in this case. While at it also
make sure that the state of the previous SBAL was successfully extracted
before inspecting it.
The i.MX8M SAI block is not compatible with the i.MX6SX one, as the
register layout has changed due to two version registers being added
at the beginning of the address map. Remove the bogus compatible.
The "struct drm_connector" iteration cursor from
"for_each_new_connector_in_state" is never used in atomic_remove_fb()
which generates a compilation warning,
drivers/gpu/drm/drm_framebuffer.c: In function 'atomic_remove_fb':
drivers/gpu/drm/drm_framebuffer.c:838:24: warning: variable 'conn' set
but not used [-Wunused-but-set-variable]
There is a couple of places where on domain_init() failure domain_exit()
is called. While currently domain_init() can fail only if
alloc_pgtable_page() has failed.
Make domain_exit() check if domain->pgd present, before calling
domain_unmap(), as it theoretically should crash on clearing pte entries
in dma_pte_clear_level().
Cc: David Woodhouse <dwmw2@infradead.org> Cc: Joerg Roedel <joro@8bytes.org> Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: iommu@lists.linux-foundation.org Signed-off-by: Dmitry Safonov <dima@arista.com> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Comparing the arm-arm's pseudocode for AArch64.PCAlignmentFault() with
AArch64.SPAlignmentFault() shows that SP faults don't copy the faulty-SP
to FAR_EL1, but this is where we read from, and the address we provide
to user-space with the BUS_ADRALN signal.
For user-space this value will be UNKNOWN due to the previous ERET to
user-space. If the last value is preserved, on systems with KASLR or KPTI
this will be the user-space link-register left in FAR_EL1 by tramp_exit().
Fix this to retrieve the original sp_el0 value, and pass this to
do_sp_pc_fault().
SP alignment faults from EL1 will cause us to take the fault again when
trying to store the pt_regs. This eventually takes us to the overflow
stack. Remove the ESR_ELx_EC_SP_ALIGN check as we will never make it
this far.
Fixes: 60ffc30d5652 ("arm64: Exception handling") Signed-off-by: James Morse <james.morse@arm.com>
[will: change label name and fleshed out comment] Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a CPU that doesn't support SSBS, PSTATE[12] is RES0. In a system
where only some of the CPUs implement SSBS, we end-up losing track of
the SSBS bit across task migration.
To address this issue, let's force the SSBS bit on context switch.
Fixes: 8f04e8e6e29c ("arm64: ssbd: Add support for PSTATE.SSBS rather than trapping to EL3") Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[will: inverted logic and added comments] Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some cases initial bind of scm memory for an lpar can fail if
previously it wasn't released using a scm-unbind hcall. This situation
can arise due to panic of the previous kernel or forced lpar
fadump. In such cases the H_SCM_BIND_MEM return a H_OVERLAP error.
To mitigate such cases the patch updates papr_scm_probe() to force a
call to drc_pmem_unbind() in case the initial bind of scm memory fails
with EBUSY error. In case scm-bind operation again fails after the
forced scm-unbind then we follow the existing error path. We also
update drc_pmem_bind() to handle the H_OVERLAP error returned by phyp
and indicate it as a EBUSY error back to the caller.
The code in occ_get_powr_avg() invokes div64_u64() without checking the
divisor. In case the divisor is zero, kernel gets an "Division by zero
in kernel" error.
Check the divisor and make it return 0 if the divisor is 0.
Fixes: c10e753d43eb ("hwmon (occ): Add sensor types and versions") Signed-off-by: Lei YU <mine260309@gmail.com> Reviewed-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/1562813088-23708-1-git-send-email-mine260309@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
allocate_flower_entry does not check for allocation success, but tries
to deref the result. I only moved the spin_lock under null check, because
the caller is checking allocation's status at line 652.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
iscsi_ibft can use ACPI to find the iBFT entry during bootup,
currently, ISCSI_IBFT depends on ISCSI_IBFT_FIND which is
a X86 legacy way to find the iBFT by searching through the
low memory. This patch changes the dependency so that other
arch like ARM64 can use ISCSI_IBFT as long as the arch supports
ACPI.
ibft_init() needs to use the global variable ibft_addr declared
in iscsi_ibft_find.c. A #ifndef CONFIG_ISCSI_IBFT_FIND is needed
to declare the variable if CONFIG_ISCSI_IBFT_FIND is not selected.
Moving ibft_addr into the iscsi_ibft.c does not work because if
ISCSI_IBFT is selected as a module, the arch/x86/kernel/setup.c won't
be able to find the variable at compile time.
Signed-off-by: Thomas Tai <thomas.tai@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com> Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.
[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: Derek Lai <Derek.Lai@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Acked-by: Tony Cheng <Tony.Cheng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com> Reviewed-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to create an inet family nat chain would not cause
nft_chain_nat.ko module to auto-load due to missing module alias. Add a
proper one with hard-coded family value 1 for the pseudo-family
NFPROTO_INET.
Fixes: d164385ec572 ("netfilter: nat: add inet family nat support") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log