Merge tag 'bcachefs-2025-04-17' of git://evilpiepirate.org/bcachefs
Pull bcachefs fixes from Kent Overstreet:
"Usual set of small fixes/logging improvements.
One bigger user reported fix, for inode <-> dirent inconsistencies
reported in fsck, after moving a subvolume that had been snapshotted"
* tag 'bcachefs-2025-04-17' of git://evilpiepirate.org/bcachefs:
bcachefs: Fix snapshotting a subvolume, then renaming it
bcachefs: Add missing READ_ONCE() for metadata replicas
bcachefs: snapshot_node_missing is now autofix
bcachefs: Log message when incompat version requested but not enabled
bcachefs: Print version_incompat_allowed on startup
bcachefs: Silence extent_poisoned error messages
bcachefs: btree_root_unreadable_and_scan_found_nothing now AUTOFIX
bcachefs: fix bch2_dev_usage_full_read_fast()
bcachefs: Don't print data read retry success on non-errors
bcachefs: Add missing error handling
bcachefs: Prevent granting write refs when filesystem is read-only
Merge tag 'vfio-v6.15-rc3' of https://github.com/awilliam/linux-vfio
Pull vfio fix from Alex Williamson:
- Include devices where the platform indicates PCI INTx is not routed
by setting pdev->irq to zero in the expanded virtualization of the
PCI pin register. This provides consistency in the INFO and SET_IRQS
ioctls (Alex Williamson)
* tag 'vfio-v6.15-rc3' of https://github.com/awilliam/linux-vfio:
vfio/pci: Virtualize zero INTx PIN if no pdev->irq
Merge tag 'spi-fix-v6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few more device specific fixes plus one trivial quirk.
There's a couple of patches for Tegra which avoid some fairly
spectacular log spam if the hardware breaks in ways which were
actually seen in production, plus a fix for the i.MX driver to
propagate errors properly when setting up the hardware.
We also have a trivial patch marking the sun4i driver as being
compatible with GPIO chip selects"
* tag 'spi-fix-v6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-imx: Add check for spi_imx_setupxfer()
spi: tegra210-quad: add rate limiting and simplify timeout error message
spi: tegra210-quad: use WARN_ON_ONCE instead of WARN_ON for timeouts
spi: sun4i: add support for GPIO chip select lines
- ipv6: add exception routes to GC list in rt6_insert_exception()
- netfilter: conntrack: fix erroneous removal of offload bit
- Bluetooth:
- fix sending MGMT_EV_DEVICE_FOUND for invalid address
- l2cap: process valid commands in too long frame
- btnxpuart: Revert baudrate change in nxp_shutdown
Previous releases - always broken:
- ethtool: fix memory corruption during SFP FW flashing
- eth:
- hibmcge: fixes for link and MTU handling, pause frames etc
- igc: fixes for PTM (PCIe timestamping)
- dsa: b53: enable BPDU reception for management port
Misc:
- fixes for Netlink protocol schemas"
* tag 'net-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits)
net: ethernet: mtk_eth_soc: revise QDMA packet scheduler settings
net: ethernet: mtk_eth_soc: correct the max weight of the queue limit for 100Mbps
net: ethernet: mtk_eth_soc: reapply mdc divider on reset
net: ti: icss-iep: Fix possible NULL pointer dereference for perout request
net: ti: icssg-prueth: Fix possible NULL pointer dereference inside emac_xmit_xdp_frame()
net: ti: icssg-prueth: Fix kernel warning while bringing down network interface
netfilter: conntrack: fix erronous removal of offload bit
net: don't try to ops lock uninitialized devs
ptp: ocp: fix start time alignment in ptp_ocp_signal_set
net: dsa: avoid refcount warnings when ds->ops->tag_8021q_vlan_del() fails
net: dsa: free routing table on probe failure
net: dsa: clean up FDB, MDB, VLAN entries on unbind
net: dsa: mv88e6xxx: fix -ENOENT when deleting VLANs and MST is unsupported
net: dsa: mv88e6xxx: avoid unregistering devlink regions which were never registered
net: txgbe: fix memory leak in txgbe_probe() error path
net: bridge: switchdev: do not notify new brentries as changed
net: b53: enable BPDU reception for management port
netlink: specs: rt-neigh: prefix struct nfmsg members with ndm
netlink: specs: rt-link: adjust mctp attribute naming
netlink: specs: rtnetlink: attribute naming corrections
...
Kent Overstreet [Thu, 17 Apr 2025 18:09:56 +0000 (14:09 -0400)]
bcachefs: Fix snapshotting a subvolume, then renaming it
Subvolume roots and the dirents that point to them are special; they
don't obey the normal snapshot versioning rules because they cross
snapshot boundaries.
We don't keep around older versions of subvolume dirents on rename - we
don't need to, because subvolume dirents are only visible in the parent
subvolume, and we wouldn't be able to match up the different dirent and
inode versions due to crossing the snapshot ID boundary.
That means that when we rename a subvolume, that's been snapshotted, the
older version of the subvolume root will become dangling - it won't have
a dirent that points to it.
That's expected, we just need to tell fsck that this is ok.
Fixes: https://github.com/koverstreet/bcachefs/issues/856 Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Merge tag 'for-linus-fwctl' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull fwctl fixes from Jason Gunthorpe:
"Three small changes from further build testing:
- Don't rely on the userspace uuid.h for the uapi header
- Fix sparse warnings in pds
- Typo in log message"
* tag 'for-linus-fwctl' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
fwctl: Fix repeated device word in log message
pds_fwctl: Fix type and endian complaints
fwctl/cxl: Fix uuid_t usage in uapi
Merge tag 'sound-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes. All are device-specific like quirks, new
IDs, and other safe (or rather boring) changes"
* tag 'sound-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
firmware: cs_dsp: test_bin_error: Fix uninitialized data used as fw version
ASoC: codecs: Add of_match_table for aw888081 driver
ASoC: fsl: fsl_qmc_audio: Reset audio data pointers on TRIGGER_START event
mailmap: Add entry for Srinivas Kandagatla
MAINTAINERS: use kernel.org alias
ASoC: cs42l43: Reset clamp override on jack removal
ALSA: hda/realtek - Fixed ASUS platform headset Mic issue
ALSA: hda/cirrus_scodec_test: Don't select dependencies
ALSA: azt2320: Replace deprecated strcpy() with strscpy()
ASoC: hdmi-codec: use RTD ID instead of DAI ID for ELD entry
ASoC: Intel: avs: Constrain path based on BE capabilities
ALSA: hda/tas2781: Remove unnecessary NULL check before release_firmware()
ASoC: Intel: avs: Fix null-ptr-deref in avs_component_probe()
ASoC: fsl_asrc_dma: get codec or cpu dai from backend
ASoC: qcom: Fix sc7280 lpass potential buffer overflow
ASoC: dwc: always enable/disable i2s irqs
ASoC: Intel: sof_sdw: Add quirk for Asus Zenbook S16
ASoC: codecs:lpass-wsa-macro: Fix logic of enabling vi channels
ASoC: codecs:lpass-wsa-macro: Fix vi feedback rate
Merge tag 'platform-drivers-x86-v6.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
"Fixes:
- amd/pmf: Fix STT limits
- asus-laptop: Fix an uninitialized variable
- intel_pmc_ipc: Allow building without ACPI
- mlxbf-bootctl: Use sysfs_emit_at() in secure_boot_fuse_state_show()
- msi-wmi-platform: Add locking to workaround ACPI firmware bug
New HW support:
- alienware-wmi-wmax:
- Extended thermal control support to:
- Alienware Area-51m R2
- Alienware m16 R1
- Alienware m16 R2
- Dell G16 7630
- Dell G5 5505 SE
- G-Mode support to Alienware m16 R1
- x86-android-tablets: Add Vexia Edu Atla 10 tablet 5V data"
* tag 'platform-drivers-x86-v6.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: msi-wmi-platform: Workaround a ACPI firmware bug
platform/x86: msi-wmi-platform: Rename "data" variable
platform/x86: alienware-wmi-wmax: Extend support to more laptops
platform/x86: alienware-wmi-wmax: Add G-Mode support to Alienware m16 R1
platform/x86: amd: pmf: Fix STT limits
mlxbf-bootctl: use sysfs_emit_at() in secure_boot_fuse_state_show()
platform/x86: x86-android-tablets: Add Vexia Edu Atla 10 tablet 5V data
platform/x86: x86-android-tablets: Add "9v" to Vexia EDU ATLA 10 tablet symbols
asus-laptop: Fix an uninitialized variable
platform/x86: intel_pmc_ipc: add option to build without ACPI
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Small drivers fixes, except for ufs which has two large updates, one
for exposing the device level feature, which is a new addition to the
device spec and the other reworking the exynos driver to fix coherence
issues on some android phones"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: megaraid_sas: Driver version update to 07.734.00.00-rc1
scsi: megaraid_sas: Block zero-length ATA VPD inquiry
scsi: scsi_transport_srp: Replace min/max nesting with clamp()
scsi: ufs: core: Add device level exception support
scsi: ufs: core: Rename ufshcd_wb_presrv_usrspc_keep_vcc_on()
scsi: smartpqi: Use is_kdump_kernel() to check for kdump
scsi: pm80xx: Set phy_attached to zero when device is gone
scsi: ufs: exynos: gs101: Put UFS device in reset on .suspend()
scsi: ufs: exynos: Move phy calls to .exit() callback
scsi: ufs: exynos: Enable PRDT pre-fetching with UFSHCD_CAP_CRYPTO
scsi: ufs: exynos: Ensure consistent phy reference counts
scsi: ufs: exynos: Disable iocc if dma-coherent property isn't set
scsi: ufs: exynos: Move UFS shareability value to drvdata
scsi: ufs: exynos: Ensure pre_link() executes before exynos_ufs_phy_init()
scsi: iscsi: Fix missing scsi_host_put() in error path
scsi: ufs: core: Fix a race condition related to device commands
scsi: hisi_sas: Fix I/O errors caused by hardware port ID changes
scsi: hisi_sas: Enable force phy when SATA disk directly connected
Merge tag 'ata-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fix from Damien Le Moal:
- Fix how sense data from the sense data for successfull NCQ commands
log page is used to fully initialize the result_tf of a completed
command, so that the sense data returned to the scsi layer is fully
initialized with all the device provided information (from Niklas)
* tag 'ata-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-sata: Save all fields from sense data descriptor
Merge tag 'xfs-fixes-6.15-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS fixes from Carlos Maiolino:
"This mostly includes fixes and documentation for the zoned allocator
feature merged during previous merge window, but it also adds a sysfs
tunable for the zone garbage collector.
There is also a fix for a regression to the RT device that we'd like
to fix ASAP now that we're getting more users on the RT zoned
allocator"
* tag 'xfs-fixes-6.15-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: document zoned rt specifics in admin-guide
xfs: fix fsmap for internal zoned devices
xfs: Fix spelling mistake "drity" -> "dirty"
xfs: compute buffer address correctly in xmbuf_map_backing_mem
xfs: add tunable threshold parameter for triggering zone GC
xfs: mark xfs_buf_free as might_sleep()
xfs: remove the leftover xfs_{set,clear}_li_failed infrastructure
Merge tag 'for-6.15-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- handle encoded read ioctl returning EAGAIN so it does not mistakenly
free the work structure
- escape subvolume path in mount option list so it cannot be wrongly
parsed when the path contains ","
- remove folio size assertions when writing super block to device with
enabled large folios
* tag 'for-6.15-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: remove folio order ASSERT()s in super block writeback path
btrfs: correctly escape subvol in btrfs_show_options()
btrfs: ioctl: don't free iov when btrfs_encoded_read() returns -EAGAIN
Merge tag 'slab-for-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fix from Vlastimil Babka:
- Stable fix adding zero initialization of slab->obj_ext to prevent
crashes with allocation profiling (Suren Baghdasaryan)
* tag 'slab-for-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: ensure slab->obj_exts is clear in a newly allocated slab page
The QDMA packet scheduler suffers from a performance issue.
Fix this by picking up changes from MediaTek's SDK which change to use
Token Bucket instead of Leaky Bucket and fix the SPEED_1000 configuration.
net: ethernet: mtk_eth_soc: reapply mdc divider on reset
In the current method, the MDC divider was reset to the default setting
of 2.5MHz after the NETSYS SER. Therefore, we need to reapply the MDC
divider configuration function in mtk_hw_init() after reset.
Paolo Abeni [Thu, 17 Apr 2025 13:20:41 +0000 (15:20 +0200)]
Merge tag 'nf-25-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fix for net
The following batch contains one Netfilter fix for net:
1) conntrack offload bit is erroneously unset in a race scenario,
from Florian Westphal.
netfilter pull request 25-04-17
* tag 'nf-25-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: conntrack: fix erronous removal of offload bit
====================
Tamura Dai [Thu, 17 Apr 2025 01:16:05 +0000 (10:16 +0900)]
spi: spi-imx: Add check for spi_imx_setupxfer()
Add check for the return value of spi_imx_setupxfer().
spi_imx->rx and spi_imx->tx function pointer can be NULL when
spi_imx_setupxfer() return error, and make NULL pointer dereference.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
0x0
spi_imx_pio_transfer+0x50/0xd8
spi_imx_transfer_one+0x18c/0x858
spi_transfer_one_message+0x43c/0x790
__spi_pump_transfer_message+0x238/0x5d4
__spi_sync+0x2b0/0x454
spi_write_then_read+0x11c/0x200
Paolo Abeni [Thu, 17 Apr 2025 11:08:41 +0000 (13:08 +0200)]
Merge tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- l2cap: Process valid commands in too long frame
- vhci: Avoid needless snprintf() calls
* tag 'for-net-2025-04-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: vhci: Avoid needless snprintf() calls
Bluetooth: l2cap: Process valid commands in too long frame
====================
====================
Bug fixes from XDP and perout series
This patch series consists of bug fixes from the XDP series:
1. Fixes a kernel warning that occurs when bringing down the
network interface.
2. Resolves a potential NULL pointer dereference in the
emac_xmit_xdp_frame() function.
3. Resolves a potential NULL pointer dereference in the
icss_iep_perout_enable() function
net: ti: icss-iep: Fix possible NULL pointer dereference for perout request
The ICSS IEP driver tracks perout and pps enable state with flags.
Currently when disabling pps and perout signals during icss_iep_exit(),
results in NULL pointer dereference for perout.
To fix the null pointer dereference issue, the icss_iep_perout_enable_hw
function can be modified to directly clear the IEP CMP registers when
disabling PPS or PEROUT, without referencing the ptp_perout_request
structure, as its contents are irrelevant in this case.
Fixes: 9b115361248d ("net: ti: icssg-prueth: Fix clearing of IEP_CMP_CFG registers during iep_init") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/7b1c7c36-363a-4085-b26c-4f210bee1df6@stanley.mountain/ Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-4-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: ti: icssg-prueth: Fix possible NULL pointer dereference inside emac_xmit_xdp_frame()
There is an error check inside emac_xmit_xdp_frame() function which
is called when the driver wants to transmit XDP frame, to check if
the allocated tx descriptor is NULL, if true to exit and return
ICSSG_XDP_CONSUMED implying failure in transmission.
In this case trying to free a descriptor which is NULL will result
in kernel crash due to NULL pointer dereference. Fix this error handling
and increase netdev tx_dropped stats in the caller of this function
if the function returns ICSSG_XDP_CONSUMED.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/70d8dd76-0c76-42fc-8611-9884937c82f5@stanley.mountain/ Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-3-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: ti: icssg-prueth: Fix kernel warning while bringing down network interface
During network interface initialization, the NIC driver needs to register
its Rx queue with the XDP, to ensure the incoming XDP buffer carries a
pointer reference to this info and is stored inside xdp_rxq_info.
While this struct isn't tied to XDP prog, if there are any changes in
Rx queue, the NIC driver needs to stop the Rx queue by unregistering
with XDP before purging and reallocating memory. Drop page_pool destroy
during Rx channel reset as this is already handled by XDP during
xdp_rxq_info_unreg (Rx queue unregister), failing to do will cause the
following warning:
Fixes: 46eeb90f03e0 ("net: ti: icssg-prueth: Use page_pool API for RX buffer allocation") Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250415090543.717991-2-m-malladi@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
netfilter: conntrack: fix erronous removal of offload bit
The blamed commit exposes a possible issue with flow_offload_teardown():
We might remove the offload bit of a conntrack entry that has been
offloaded again.
1. conntrack entry c1 is offloaded via flow f1 (f1->ct == c1).
2. f1 times out and is pushed back to slowpath, c1 offload bit is
removed. Due to bug, f1 is not unlinked from rhashtable right away.
3. a new packet arrives for the flow and re-offload is triggered, i.e.
f2->ct == c1. This is because lookup in flowtable skip entries with
teardown bit set.
4. Next flowtable gc cycle finds f1 again
5. flow_offload_teardown() is called again for f1 and c1 offload bit is
removed again, even though we have f2 referencing the same entry.
This is harmless, but clearly not correct.
Fix the bug that exposes this: set 'teardown = true' to have the gc
callback unlink the flowtable entry from the table right away instead of
the unintentional defer to the next round.
Also prevent flow_offload_teardown() from fixing up the ct state more than
once: We could also be called from the data path or a notifier, not only
from the flowtable gc callback.
NF_FLOW_TEARDOWN can never be unset, so we can use it as synchronization
point: if we observe did not see a 0 -> 1 transition, then another CPU
is already doing the ct state fixups for us.
Hans Holmberg [Wed, 9 Apr 2025 12:39:56 +0000 (12:39 +0000)]
xfs: document zoned rt specifics in admin-guide
Document the lifetime, nolifetime and max_open_zones mount options
added for zoned rt file systems.
Also add documentation describing the max_open_zones sysfs attribute
exposed in /sys/fs/xfs/<dev>/zoned/
Fixes: 4e4d52075577 ("xfs: add the zoned space allocator") Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Merge tag 'mm-hotfixes-stable-2025-04-16-19-59' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"31 hotfixes.
9 are cc:stable and the remainder address post-6.15 issues or aren't
considered necessary for -stable kernels.
22 patches are for MM, 9 are otherwise"
* tag 'mm-hotfixes-stable-2025-04-16-19-59' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (31 commits)
MAINTAINERS: update HUGETLB reviewers
mm: fix apply_to_existing_page_range()
selftests/mm: fix compiler -Wmaybe-uninitialized warning
alloc_tag: handle incomplete bulk allocations in vm_module_tags_populate
mailmap: add entry for Jean-Michel Hautbois
mm: (un)track_pfn_copy() fix + doc improvements
mm: fix filemap_get_folios_contig returning batches of identical folios
mm/hugetlb: add a line break at the end of the format string
selftests: mincore: fix tmpfs mincore test failure
mm/hugetlb: fix set_max_huge_pages() when there are surplus pages
mm/cma: report base address of single range correctly
mm: page_alloc: speed up fallbacks in rmqueue_bulk()
kunit: slub: add module description
mm/kasan: add module decription
ucs2_string: add module description
zlib: add module description
fpga: tests: add module descriptions
samples/livepatch: add module descriptions
ASN.1: add module description
mm/vma: add give_up_on_oom option on modify/merge, use in uffd release
...
Jakub Kicinski [Tue, 15 Apr 2025 15:15:52 +0000 (08:15 -0700)]
net: don't try to ops lock uninitialized devs
We need to be careful when operating on dev while in rtnl_create_link().
Some devices (vxlan) initialize netdev_ops in ->newlink, so later on.
Avoid using netdev_lock_ops(), the device isn't registered so we
cannot legally call its ops or generate any notifications for it.
netdev_ops_assert_locked_or_invisible() is safe to use, it checks
registration status first.
Reported-by: syzbot+de1c7d68a10e3f123bdd@syzkaller.appspotmail.com Fixes: 04efcee6ef8d ("net: hold instance lock during NETDEV_CHANGE") Acked-by: Stanislav Fomichev <sdf@fomichev.me> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20250415151552.768373-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ptp: ocp: fix start time alignment in ptp_ocp_signal_set
In ptp_ocp_signal_set, the start time for periodic signals is not
aligned to the next period boundary. The current code rounds up the
start time and divides by the period but fails to multiply back by
the period, causing misaligned signal starts. Fix this by multiplying
the rounded-up value by the period to ensure the start time is the
closest next period.
Fixes: 4bd46bb037f8e ("ptp: ocp: Use DIV64_U64_ROUND_UP for rounding.") Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250415053131.129413-1-maimon.sagi@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 17 Apr 2025 01:14:45 +0000 (18:14 -0700)]
Merge branch 'collection-of-dsa-bug-fixes'
Vladimir Oltean says:
====================
Collection of DSA bug fixes
Prompted by Russell King's 3 DSA bug reports from Friday (linked in
their respective patches: 1, 2 and 3), I am providing fixes to those, as
well as flushing the queue with 2 other bug fixes I had.
1: fix NULL pointer dereference during mv88e6xxx driver unbind, on old
switch models which lack PVT and/or STU. Seen on the ZII dev board
rev B.
2: fix failure to delete bridge port VLANs on old mv88e6xxx chips which
lack STU. Seen on the same board.
3: fix WARN_ON() and resource leak in DSA core on driver unbind. Seen on
the same board but is a much more widespread issue.
4: fix use-after-free during probing of DSA trees with >= 3 switches,
if -EPROBE_DEFER exists. In principle issue also exists for the ZII
board, I reproduced on Turris MOX.
5: fix incorrect use of refcount API in DSA core for those switches
which use tag_8021q (felix, sja1105, vsc73xx). Returning an error
when attempting to delete a tag_8021q VLAN prints a WARN_ON(), which
is harmless but might be problematic with CONFIG_PANIC_ON_OOPS.
====================
Vladimir Oltean [Mon, 14 Apr 2025 21:30:20 +0000 (00:30 +0300)]
net: dsa: avoid refcount warnings when ds->ops->tag_8021q_vlan_del() fails
This is very similar to the problem and solution from commit 232deb3f9567 ("net: dsa: avoid refcount warnings when
->port_{fdb,mdb}_del returns error"), except for the
dsa_port_do_tag_8021q_vlan_del() operation.
Vladimir Oltean [Mon, 14 Apr 2025 21:30:01 +0000 (00:30 +0300)]
net: dsa: free routing table on probe failure
If complete = true in dsa_tree_setup(), it means that we are the last
switch of the tree which is successfully probing, and we should be
setting up all switches from our probe path.
After "complete" becomes true, dsa_tree_setup_cpu_ports() or any
subsequent function may fail. If that happens, the entire tree setup is
in limbo: the first N-1 switches have successfully finished probing
(doing nothing but having allocated persistent memory in the tree's
dst->ports, and maybe dst->rtable), and switch N failed to probe, ending
the tree setup process before anything is tangible from the user's PoV.
If switch N fails to probe, its memory (ports) will be freed and removed
from dst->ports. However, the dst->rtable elements pointing to its ports,
as created by dsa_link_touch(), will remain there, and will lead to
use-after-free if dereferenced.
If dsa_tree_setup_switches() returns -EPROBE_DEFER, which is entirely
possible because that is where ds->ops->setup() is, we get a kasan
report like this:
==================================================================
BUG: KASAN: slab-use-after-free in mv88e6xxx_setup_upstream_port+0x240/0x568
Read of size 8 at addr ffff000004f56020 by task kworker/u8:3/42
The simplest way to fix the bug is to delete the routing table in its
entirety. dsa_tree_setup_routing_table() has no problem in regenerating
it even if we deleted links between ports other than those of switch N,
because dsa_link_touch() first checks whether the port pair already
exists in dst->rtable, allocating if not.
The deletion of the routing table in its entirety already exists in
dsa_tree_teardown(), so refactor that into a function that can also be
called from the tree setup error path.
In my analysis of the commit to blame, it is the one which added
dsa_link elements to dst->rtable. Prior to that, each switch had its own
ds->rtable which is freed when the switch fails to probe. But the tree
is potentially persistent memory.
Vladimir Oltean [Mon, 14 Apr 2025 21:29:30 +0000 (00:29 +0300)]
net: dsa: clean up FDB, MDB, VLAN entries on unbind
As explained in many places such as commit b117e1e8a86d ("net: dsa:
delete dsa_legacy_fdb_add and dsa_legacy_fdb_del"), DSA is written given
the assumption that higher layers have balanced additions/deletions.
As such, it only makes sense to be extremely vocal when those
assumptions are violated and the driver unbinds with entries still
present.
But Ido Schimmel points out a very simple situation where that is wrong:
https://lore.kernel.org/netdev/ZDazSM5UsPPjQuKr@shredder/
(also briefly discussed by me in the aforementioned commit).
Basically, while the bridge bypass operations are not something that DSA
explicitly documents, and for the majority of DSA drivers this API
simply causes them to go to promiscuous mode, that isn't the case for
all drivers. Some have the necessary requirements for bridge bypass
operations to do something useful - see dsa_switch_supports_uc_filtering().
Although in tools/testing/selftests/net/forwarding/local_termination.sh,
we made an effort to popularize better mechanisms to manage address
filters on DSA interfaces from user space - namely macvlan for unicast,
and setsockopt(IP_ADD_MEMBERSHIP) - through mtools - for multicast, the
fact is that 'bridge fdb add ... self static local' also exists as
kernel UAPI, and might be useful to someone, even if only for a quick
hack.
It seems counter-productive to block that path by implementing shim
.ndo_fdb_add and .ndo_fdb_del operations which just return -EOPNOTSUPP
in order to prevent the ndo_dflt_fdb_add() and ndo_dflt_fdb_del() from
running, although we could do that.
Accepting that cleanup is necessary seems to be the only option.
Especially since we appear to be coming back at this from a different
angle as well. Russell King is noticing that the WARN_ON() triggers even
for VLANs:
https://lore.kernel.org/netdev/Z_li8Bj8bD4-BYKQ@shell.armlinux.org.uk/
What happens in the bug report above is that dsa_port_do_vlan_del() fails,
then the VLAN entry lingers on, and then we warn on unbind and leak it.
This is not a straight revert of the blamed commit, but we now add an
informational print to the kernel log (to still have a way to see
that bugs exist), and some extra comments gathered from past years'
experience, to justify the logic.
Vladimir Oltean [Mon, 14 Apr 2025 21:29:13 +0000 (00:29 +0300)]
net: dsa: mv88e6xxx: fix -ENOENT when deleting VLANs and MST is unsupported
Russell King reports that on the ZII dev rev B, deleting a bridge VLAN
from a user port fails with -ENOENT:
https://lore.kernel.org/netdev/Z_lQXNP0s5-IiJzd@shell.armlinux.org.uk/
This comes from mv88e6xxx_port_vlan_leave() -> mv88e6xxx_mst_put(),
which tries to find an MST entry in &chip->msts associated with the SID,
but fails and returns -ENOENT as such.
But we know that this chip does not support MST at all, so that is not
surprising. The question is why does the guard in mv88e6xxx_mst_put()
not exit early:
if (!sid)
return 0;
And the answer seems to be simple: the sid comes from vlan.sid which
supposedly was previously populated by mv88e6xxx_vtu_get().
But some chip->info->ops->vtu_getnext() implementations do not populate
vlan.sid, for example see mv88e6185_g1_vtu_getnext(). In that case,
later in mv88e6xxx_port_vlan_leave() we are using a garbage sid which is
just residual stack memory.
Testing for sid == 0 covers all cases of a non-bridge VLAN or a bridge
VLAN mapped to the default MSTI. For some chips, SID 0 is valid and
installed by mv88e6xxx_stu_setup(). A chip which does not support the
STU would implicitly only support mapping all VLANs to the default MSTI,
so although SID 0 is not valid, it would be sufficient, if we were to
zero-initialize the vlan structure, to fix the bug, due to the
coincidence that a test for vlan.sid == 0 already exists and leads to
the same (correct) behavior.
Another option which would be sufficient would be to add a test for
mv88e6xxx_has_stu() inside mv88e6xxx_mst_put(), symmetric to the one
which already exists in mv88e6xxx_mst_get(). But that placement means
the caller will have to dereference vlan.sid, which means it will access
uninitialized memory, which is not nice even if it ignores it later.
So we end up making both modifications, in order to not rely just on the
sid == 0 coincidence, but also to avoid having uninitialized structure
fields which might get temporarily accessed.
Vladimir Oltean [Mon, 14 Apr 2025 21:28:50 +0000 (00:28 +0300)]
net: dsa: mv88e6xxx: avoid unregistering devlink regions which were never registered
Russell King reports that a system with mv88e6xxx dereferences a NULL
pointer when unbinding this driver:
https://lore.kernel.org/netdev/Z_lRkMlTJ1KQ0kVX@shell.armlinux.org.uk/
The crash seems to be in devlink_region_destroy(), which is not NULL
tolerant but is given a NULL devlink global region pointer.
At least on some chips, some devlink regions are conditionally registered
since the blamed commit, see mv88e6xxx_setup_devlink_regions_global():
if (cond && !cond(chip))
continue;
These are MV88E6XXX_REGION_STU and MV88E6XXX_REGION_PVT. If the chip
does not have an STU or PVT, it should crash like this.
To fix the issue, avoid unregistering those regions which are NULL, i.e.
were skipped at mv88e6xxx_setup_devlink_regions_global() time.
Fixes: 836021a2d0e0 ("net: dsa: mv88e6xxx: Export cross-chip PVT as devlink region") Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250414212850.2953957-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: txgbe: fix memory leak in txgbe_probe() error path
When txgbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in txgbe_probe() function, the subsequent
error paths after txgbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when txgbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Jonas Gorski [Mon, 14 Apr 2025 20:00:20 +0000 (22:00 +0200)]
net: bridge: switchdev: do not notify new brentries as changed
When adding a bridge vlan that is pvid or untagged after the vlan has
already been added to any other switchdev backed port, the vlan change
will be propagated as changed, since the flags change.
This causes the vlan to not be added to the hardware for DSA switches,
since the DSA handler ignores any vlans for the CPU or DSA ports that
are changed.
E.g. the following order of operations would work:
$ ip link add swbridge type bridge vlan_filtering 1 vlan_default_pvid 0
$ ip link set lan1 master swbridge
$ bridge vlan add dev swbridge vid 1 pvid untagged self
$ bridge vlan add dev lan1 vid 1 pvid untagged
but this order would break:
$ ip link add swbridge type bridge vlan_filtering 1 vlan_default_pvid 0
$ ip link set lan1 master swbridge
$ bridge vlan add dev lan1 vid 1 pvid untagged
$ bridge vlan add dev swbridge vid 1 pvid untagged self
Additionally, the vlan on the bridge itself would become undeletable:
$ bridge vlan
port vlan-id
lan1 1 PVID Egress Untagged
swbridge 1 PVID Egress Untagged
$ bridge vlan del dev swbridge vid 1 self
$ bridge vlan
port vlan-id
lan1 1 PVID Egress Untagged
swbridge 1 Egress Untagged
since the vlan was never added to DSA's vlan list, so deleting it will
cause an error, causing the bridge code to not remove it.
Fix this by checking if flags changed only for vlans that are already
brentry and pass changed as false for those that become brentries, as
these are a new vlan (member) from the switchdev point of view.
Since *changed is set to true for becomes_brentry = true regardless of
would_change's value, this will not change any rtnetlink notification
delivery, just the value passed on to switchdev in vlan->changed.
Fixes: 8d23a54f5bee ("net: bridge: switchdev: differentiate new VLANs from changed ones") Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250414200020.192715-1-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Gorski [Mon, 14 Apr 2025 20:04:34 +0000 (22:04 +0200)]
net: b53: enable BPDU reception for management port
For STP to work, receiving BPDUs is essential, but the appropriate bit
was never set. Without GC_RX_BPDU_EN, the switch chip will filter all
BPDUs, even if an appropriate PVID VLAN was setup.
====================
ynl: avoid leaks in attr override and spec fixes for C
The C rt-link work revealed more problems in existing codegen
and classic netlink specs.
Patches 1 - 4 fix issues with the codegen. Patches 1 and 2 are
pre-requisites for patch 3. Patch 3 fixes leaking memory if user
tries to override already set attr. Patch 4 validates attrs in case
kernel sends something we don't expect.
Remaining patches fix and align the specs. Patch 5 changes nesting,
the rest are naming adjustments.
====================
Jakub Kicinski [Mon, 14 Apr 2025 21:18:51 +0000 (14:18 -0700)]
netlink: specs: rt-neigh: prefix struct nfmsg members with ndm
Attach ndm- to all members of struct nfmsg. We could possibly
use name-prefix just for C, but I don't think we have any precedent
for using name-prefix on structs, and other rtnetlink sub-specs
give full names for fixed header struct members.
Fixes: bc515ed06652 ("netlink: specs: Add a spec for neighbor tables in rtnetlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-9-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MCTP attribute naming is inconsistent. In C we have:
IFLA_MCTP_NET,
IFLA_MCTP_PHYS_BINDING,
^^^^
but in YAML:
- mctp-net
- phys-binding
^
no "mctp"
It's unclear whether the "mctp" part of the name is supposed
to be a prefix or part of attribute name. Make it a prefix,
seems cleaner, even tho technically phys-binding was added later.
Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-8-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some attribute names diverge in very minor ways from the C names.
These are most likely typos, and they prevent the C codegen from
working.
Fixes: bc515ed06652 ("netlink: specs: Add a spec for neighbor tables in rtnetlink") Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-7-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:48 +0000 (14:18 -0700)]
netlink: specs: rt-link: add an attr layer around alt-ifname
alt-ifname attr is directly placed in requests (as an alternative
to ifname) but in responses its wrapped up in IFLA_PROP_LIST
and only there is may be multi-attr. See rtnl_fill_prop_list().
Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-6-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:47 +0000 (14:18 -0700)]
tools: ynl-gen: make sure we validate subtype of array-nest
ArrayNest AKA indexed-array support currently skips inner type
validation. We count the attributes and then we parse them,
make sure we call validate, too. Otherwise buggy / unexpected
kernel response may lead to crashes.
Fixes: be5bea1cc0bf ("net: add basic C code generators for Netlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-5-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:46 +0000 (14:18 -0700)]
tools: ynl-gen: individually free previous values on double set
When user calls request_attrA_set() multiple times (for the same
attribute), and attrA is of type which allocates memory -
we try to free the previously associated values. For array
types (including multi-attr) we have only freed the array,
but the array may have contained pointers.
Refactor the code generation for free attr and reuse the generated
lines in setters to flush out the previous state. Since setters
are static inlines in the header we need to add forward declarations
for the free helpers of pure nested structs. Track which types get
used by arrays and include the right forwad declarations.
At least ethtool string set and bit set would not be freed without
this. Tho, admittedly, overriding already set attribute twice is likely
a very very rare thing to do.
Fixes: be5bea1cc0bf ("net: add basic C code generators for Netlink") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414211851.602096-4-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 21:18:45 +0000 (14:18 -0700)]
tools: ynl-gen: move local vars after the opening bracket
The "function writing helper" tries to put local variables
between prototype and the opening bracket. Clearly wrong,
but up until now nothing actually uses it to write local
vars so it wasn't noticed.
Jakub Kicinski [Mon, 14 Apr 2025 21:18:44 +0000 (14:18 -0700)]
tools: ynl-gen: don't declare loop iterator in place
The codegen tries to follow the "old" C style and declare loop
iterators at the start of the block / function. Only nested
request handling breaks this style, so adjust it.
cxgb4: fix memory leak in cxgb4_init_ethtool_filters() error path
In the for loop used to allocate the loc_array and bmap for each port, a
memory leak is possible when the allocation for loc_array succeeds,
but the allocation for bmap fails. This is because when the control flow
goes to the label free_eth_finfo, only the allocations starting from
(i-1)th iteration are freed.
Fix that by freeing the loc_array in the bmap allocation error path.
Fixes: d915c299f1da ("cxgb4: add skeleton for ethtool n-tuple filters") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250414170649.89156-1-abdun.nihaal@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid double-copying of string literals. Use a "const char *" for each
string instead of copying from .rodata into stack and then into the skb.
We can go directly from .rodata to the skb.
This also works around a Clang bug (that has since been fixed[1]).
Bluetooth: l2cap: Process valid commands in too long frame
This is required for passing PTS test cases:
- L2CAP/COS/CED/BI-14-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Connection Request
- L2CAP/COS/CED/BI-15-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Disconnection Request
The test procedure defined in L2CAP.TS.p39 for both tests is:
1. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 8 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains one L2CAP_ECHO_REQ
packet with Data Length set to 0 with 0 octets of echo data and
one command packet and Data Length set as specified in Table 4.6
and the correct command data.
2. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
3. Perform alternative 3A, 3B, 3C, or 3D depending on the IUT’s
response.
Alternative 3A (IUT terminates the link):
3A.1 The IUT terminates the link.
3A.2 The test ends with a Pass verdict.
Alternative 3B (IUT discards the frame):
3B.1 The IUT does not send a reply to the Lower Tester.
Alternative 3C (IUT rejects PDU):
3C.1 The IUT sends an L2CAP_COMMAND_REJECT_RSP PDU to the
Lower Tester.
Alternative 3D (Any other IUT response):
3D.1 The Upper Tester issues a warning and the test ends.
4. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 4 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains Data Length set to
0 with an L2CAP_ECHO_REQ packet with 0 octets of echo data.
5. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
With expected outcome:
In Steps 2 and 5, the IUT responds with an L2CAP_ECHO_RSP.
In Step 3A.1, the IUT terminates the link.
In Step 3B.1, the IUT does not send a reply to the Lower Tester.
In Step 3C.1, the IUT rejects the PDU.
In Step 3D.1, the IUT sends any valid response.
Currently PTS fails with the following logs:
Failed to receive ECHO RESPONSE.
And HCI logs:
> ACL Data RX: Handle 11 flags 0x02 dlen 20
L2CAP: Information Response (0x0b) ident 2 len 12
Type: Fixed channels supported (0x0003)
Result: Success (0x0000)
Channels: 0x000000000000002e
L2CAP Signaling (BR/EDR)
Connectionless reception
AMP Manager Protocol
L2CAP Signaling (LE)
> ACL Data RX: Handle 11 flags 0x02 dlen 13
frame too long
08 01 00 00 08 02 01 00 aa .........
Cc: stable@vger.kernel.org Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Darrick J. Wong [Tue, 15 Apr 2025 00:33:45 +0000 (17:33 -0700)]
xfs: fix fsmap for internal zoned devices
Filesystems with an internal zoned rt section use xfs_rtblock_t values
that are relative to the start of the data device. When fsmap reports
on internal rt sections, it reports the space used by the data section
as "OWN_FS".
Unfortunately, the logic for resuming a query isn't quite right, so
xfs/273 fails because it stress-tests GETFSMAP with a single-record
buffer. If we enter the "report fake space as OWN_FS" block with a
nonzero key[0].fmr_length, we should add that to key[0].fmr_physical
and recheck if we still need to emit the fake record. We should /not/
just return 0 from the whole function because that prevents all rmap
record iteration.
If we don't enter that block, the resumption is still wrong.
keys[*].fmr_physical is a reflection of what we copied out to userspace
on a previous query, which means that it already accounts for rgstart.
It is not correct to add rtstart_daddr when computing start_rtb or
end_rtb, so stop that.
While we're at it, add a xfs_has_zoned to make it clear that this is a
zoned filesystem thing.
Fixes: e50ec7fac81aa2 ("xfs: enable fsmap reporting for internal RT devices") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Zhang Xianwei [Sat, 15 Mar 2025 06:32:16 +0000 (14:32 +0800)]
xfs: Fix spelling mistake "drity" -> "dirty"
There is a spelling mistake in fs/xfs/xfs_log.c. Fix it.
Signed-off-by: Zhang Xianwei <zhang.xianwei8@zte.com.cn> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
ata: libata-sata: Save all fields from sense data descriptor
When filling the taskfile result for a successful NCQ command, we use
the SDB FIS from the FIS Receive Area, see e.g. ahci_qc_ncq_fill_rtf().
However, the SDB FIS only has fields STATUS and ERROR.
For a successful NCQ command that has sense data, we will have a
successful sense data descriptor, in the Sense Data for Successful NCQ
Commands log.
Since we have access to additional taskfile result fields, fill in these
additional fields in qc->result_tf.
This matches how for failing/aborted NCQ commands, we will use e.g.
ahci_qc_fill_rtf() to fill in some fields, but then for the command that
actually caused the NCQ error, we will use ata_eh_read_log_10h(), which
provides additional fields, saving additional fields/overriding the
qc->result_tf that was fetched using ahci_qc_fill_rtf().
Fixes: 18bd7718b5c4 ("scsi: ata: libata: Handle completion of CDL commands using policy 0xD") Signed-off-by: Niklas Cassel <cassel@kernel.org> Reviewed-by: Igor Pylypiv <ipylypiv@google.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Armin Wolf [Mon, 14 Apr 2025 14:04:53 +0000 (16:04 +0200)]
platform/x86: msi-wmi-platform: Workaround a ACPI firmware bug
The ACPI byte code inside the ACPI control method responsible for
handling the WMI method calls uses a global buffer for constructing
the return value, yet the ACPI control method itself is not marked
as "Serialized".
This means that calling WMI methods on this WMI device is not
thread-safe, as concurrent WMI method calls will corrupt the global
buffer.
Fix this by serializing the WMI method calls using a mutex.
Sven Eckelmann [Mon, 14 Apr 2025 18:05:37 +0000 (20:05 +0200)]
batman-adv: Fix double-hold of meshif when getting enabled
It was originally meant to replace the dev_hold with netdev_hold. But this
was missed in batadv_hardif_enable_interface(). As result, there was an
imbalance and a hang when trying to remove the mesh-interface with
(previously) active hard-interfaces:
unregister_netdevice: waiting for batadv0 to become free. Usage count = 3
Fixes: 00b35530811f ("batman-adv: adopt netdev_hold() / netdev_put()") Suggested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+ff3aa851d46ab82953a3@syzkaller.appspotmail.com Reported-by: syzbot+4036165fc595a74b09b2@syzkaller.appspotmail.com Reported-by: syzbot+c35d73ce910d86c0026e@syzkaller.appspotmail.com Reported-by: syzbot+48c14f61594bdfadb086@syzkaller.appspotmail.com Reported-by: syzbot+f37372d86207b3bb2941@syzkaller.appspotmail.com Signed-off-by: Sven Eckelmann <sven@narfation.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250414-double_hold_fix-v5-1-10e056324cde@narfation.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before commit 40867d74c374 ("net: Add l3mdev index to flow struct and
avoid oif reset for port devices") it was possible to use FIB rules to
match on a L3 domain. This was done by having a FIB rule match on iif /
oif being a L3 master device. It worked because prior to the FIB rule
lookup the iif / oif fields in the flow structure were reset to the
index of the L3 master device to which the input / output device was
enslaved to.
The above scheme made it impossible to match on the original input /
output device. Therefore, cited commit stopped overwriting the iif / oif
fields in the flow structure and instead stored the index of the
enslaving L3 master device in a new field ('flowi_l3mdev') in the flow
structure.
While the change enabled new use cases, it broke the original use case
of matching on a L3 domain. Fix this by interpreting the iif / oif
matching on a L3 master device as a match against the L3 domain. In
other words, if the iif / oif in the FIB rule points to a L3 master
device, compare the provided index against 'flowi_l3mdev' rather than
'flowi_{i,o}if'.
Before cited commit, a FIB rule that matched on 'iif vrf1' would only
match incoming traffic from devices enslaved to 'vrf1'. With the
proposed change (i.e., comparing against 'flowi_l3mdev'), the rule would
also match traffic originating from a socket bound to 'vrf1'. Avoid that
by adding a new flow flag ('FLOWI_FLAG_L3MDEV_OIF') that indicates if
the L3 domain was derived from the output interface or the input
interface (when not set) and take this flag into account when evaluating
the FIB rule against the flow structure.
Avoid unnecessary checks in the data path by detecting that a rule
matches on a L3 master device when the rule is installed and marking it
as such.
ip route add table 100 default dev dummy1
ip route add table 200 default dev dummy1
ip route add table 300 default dev dummy1
ip rule add prio 0 oif vrf1 table 100
ip rule add prio 1 iif vrf1 table 200
ip rule add prio 2 table 300
ip route get 192.0.2.1 oif dummy1 fibmatch
ip route get 192.0.2.1 iif dummy1 from 198.51.100.1 fibmatch
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices") Reported-by: hanhuihui <hanhuihui5@huawei.com> Closes: https://lore.kernel.org/netdev/ec671c4f821a4d63904d0da15d604b75@huawei.com/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250414172022.242991-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 14 Apr 2025 14:32:10 +0000 (07:32 -0700)]
eth: bnxt: fix missing ring index trim on error path
Commit under Fixes converted tx_prod to be free running but missed
masking it on the Tx error path. This crashes on error conditions,
for example when DMA mapping fails.
A reference to the device tree node is stored in a private struct, thus
the reference count has to be incremented. Also, decrement the count on
device removal and in the error path.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Michael Walle <mwalle@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250414083942.4015060-1-mwalle@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
spi: tegra210-quad: add rate limiting and simplify timeout error message
On malfunctioning hardware, timeout error messages can appear thousands
of times, creating unnecessary system pressure and log bloat. This patch
makes two improvements:
1. Replace dev_err() with dev_err_ratelimited() to prevent log flooding
when hardware errors persist
2. Remove the redundant timeout value parameter from the error message,
as 'ret' is always zero in this error path
These changes reduce logging overhead while maintaining necessary error
reporting for debugging purposes.
This patch replaces WARN_ON with WARN_ON_ONCE for timeout conditions to
reduce log spam. The subsequent error message still prints on each
occurrence, providing sufficient information about the failure, while
the stack trace is only needed once for debugging purposes.
Merge tag 'edac_urgent_for_v6.15_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fixes from Borislav Petkov:
"Two fixes to the AMD translation library for the MI300 side of things:
- Use the row[13] bit when calculating the memory row to retire
- Mask the physical row address in order to avoid creating duplicate
error records"
* tag 'edac_urgent_for_v6.15_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
RAS/AMD/FMPM: Get masked address
RAS/AMD/ATL: Include row[13] bit in row retirement
net: ngbe: fix memory leak in ngbe_probe() error path
When ngbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in ngbe_probe() function, the subsequent
error paths after ngbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when ngbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Fixes: 02338c484ab6 ("net: ngbe: Initialize sw info and register netdev") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com> Link: https://patch.msgid.link/20250412154927.25908-1-abdun.nihaal@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename the "data" variable inside msi_wmi_platform_read() to avoid
a name collision when the driver adds support for a state container
struct (that is to be called "data" too) in the future.
Jakub Kicinski [Mon, 14 Apr 2025 22:58:30 +0000 (15:58 -0700)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
igc: Fix PTM timeout
Christopher S M Hall says:
There have been sporadic reports of PTM timeouts using i225/i226 devices
These timeouts have been root caused to:
1) Manipulating the PTM status register while PTM is enabled
and triggered
2) The hardware retrying too quickly when an inappropriate response
is received from the upstream device
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
The first patch in this series also resolves an issue reported by Corinna
Vinschen relating to kdump:
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not zero, but extremly reduced.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: add lock preventing multiple simultaneous PTM transactions
igc: cleanup PTP module if probe fails
igc: handle the IGC_PTP_ENABLED flag correctly
igc: move ktime snapshot into PTM retry loop
igc: increase wait time before retrying PTM
igc: fix PTM cycle trigger logic
====================
Oscar Salvador [Wed, 9 Apr 2025 08:24:52 +0000 (10:24 +0200)]
MAINTAINERS: update HUGETLB reviewers
I have done quite some review on hugetlb code over the years, and some
work on it as well, the latest being the hugetlb pagewalk unification
which is a work in progress, and touches hugetlb code to great lengths.
HugeTLB does not have many reviewers, so I would like to help out by
offering myself as an official Reviewer.
Signed-off-by: Oscar Salvador <osalvador@suse.de> Link: https://lkml.kernel.org/r/20250409082452.269180-1-osalvador@suse.de Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Muchun Song <muchun.song@linux.dev> Cc: Michal Hocko <mhocko@suse.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Jakub Kicinski [Wed, 9 Apr 2025 14:55:41 +0000 (07:55 -0700)]
netlink: specs: ovs_vport: align with C codegen capabilities
We started generating C code for OvS a while back, but actually
C codegen only supports fixed headers specified at the family
level right now (schema also allows specifying them per op).
ovs_flow and ovs_datapath already specify the fixed header
at the family level but ovs_vport does it per op.
Move the property, all ops use the same header.
The first dependency is the problem. wiphy mutex should be outside
the instance locks. The problem happens in notifiers (as always)
for CLOSE. We only hold the instance lock for ops locked devices
during CLOSE, and WiFi netdevs are not ops locked. Unfortunately,
when we dev_close_many() during netns dismantle we may be holding
the instance lock of _another_ netdev when issuing a CLOSE for
a WiFi device.
Lockdep's "Possible unsafe locking scenario" only prints 3 locks
and we have 4, plus I think we'd need 3 CPUs, like this:
Tho, I don't think that's possible as CPU1 and CPU2 would
be under rtnl_lock. Even if we have per-netns rtnl_lock and
wiphy can span network namespaces - CPU0 and CPU1 must be
in the same netns to see dev_instance_lock, so CPU0 can't
be installing a socket as CPU1 is tearing the netns down.
Regardless, our expected lock ordering is that wiphy lock
is taken before instance locks, so let's fix this.
Go over the ops locked and non-locked devices separately.
Note that calling dev_close_many() on an empty list is perfectly
fine. All processing (including RCU syncs) are conditional
on the list not being empty, already.
Fixes: 7e4d784f5810 ("net: hold netdev instance lock during rtnetlink operations") Reported-by: syzbot+6f588c78bf765b62b450@syzkaller.appspotmail.com Acked-by: Stanislav Fomichev <sdf@fomichev.me> Link: https://patch.msgid.link/20250412233011.309762-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'vfs-6.15-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Fix NULL pointer dereference in virtiofs
- Fix slab OOB access in hfs/hfsplus
- Only create /proc/fs/netfs when CONFIG_PROC_FS is set
- Fix getname_flags() to initialize pointer correctly
- Convert dentry flags to enum
- Don't allow datadir without lowerdir in overlayfs
- Use namespace_{lock,unlock} helpers in dissolve_on_fput() instead of
plain namespace_sem so unmounted mounts are properly cleaned up
- Skip unnecessary ifs_block_is_uptodate check in iomap
- Remove an unused forward declaration in overlayfs
- Fix devpts uid/gid handling after converting to the new mount api
- Fix afs_dynroot_readdir() to not use the RCU read lock
- Fix mount_setattr() and open_tree_attr() to not pointlessly do path
lookup or walk the mount tree if no mount option change has been
requested
* tag 'vfs-6.15-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: use namespace_{lock,unlock} in dissolve_on_fput()
iomap: skip unnecessary ifs_block_is_uptodate check
fs: Fix filename init after recent refactoring
netfs: Only create /proc/fs/netfs with CONFIG_PROC_FS
mount: ensure we don't pointlessly walk the mount tree
dcache: convert dentry flag macros to enum
afs: Fix afs_dynroot_readdir() to not use the RCU read lock
hfs/hfsplus: fix slab-out-of-bounds in hfs_bnode_read_key
virtiofs: add filesystem context source name check
devpts: Fix type for uid and gid params
ovl: remove unused forward declaration
ovl: don't allow datadir only
Merge tag 'perf-tools-fixes-for-v6.15-2025-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tools fixes from Namhyung Kim:
"A couple of fixes and the usual tooling header updates:
- fix a build error on ARM64 when libunwind is requested
- fix an infinite loop with branch stack on AMD Zen3
- sync tooling headers with the kernel source"
* tag 'perf-tools-fixes-for-v6.15-2025-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
perf tools: Remove evsel__handle_error_quirks()
perf libunwind arm64: Fix missing close parens in an if statement
tools headers: Update the arch/x86/lib/memset_64.S copy with the kernel sources
tools headers: Update the x86 headers with the kernel sources
tools headers: Update the linux/unaligned.h copy with the kernel sources
tools headers: Update the uapi/asm-generic/mman-common.h copy with the kernel sources
tools headers: Update the uapi/linux/prctl.h copy with the kernel sources
tools headers: Update the syscall table with the kernel sources
tools headers: Update the VFS headers with the kernel sources
tools headers: Update the uapi/linux/perf_event.h copy with the kernel sources
tools headers: Update the socket headers with the kernel sources
tools headers: Update the KVM headers with the kernel sources
Alex Williamson [Thu, 20 Mar 2025 19:41:42 +0000 (13:41 -0600)]
vfio/pci: Virtualize zero INTx PIN if no pdev->irq
Typically pdev->irq is consistent with whether the device itself
supports INTx, where device support is reported via the PIN register.
Therefore the PIN register is often already zero if pdev->irq is zero.
Recently virtualization of the PIN register was expanded to include
the case where the device supports INTx but the platform does not
route the interrupt. This is reported by a value of IRQ_NOTCONNECTED
on some architectures. Other architectures just report zero for
pdev->irq.
We already disallow INTx setup if pdev->irq is zero, therefore add
this to the PIN register virtualization criteria so that a consistent
view is provided to userspace through virtualized config space and
ioctls.
slab: ensure slab->obj_exts is clear in a newly allocated slab page
ktest recently reported crashes while running several buffered io tests
with __alloc_tagging_slab_alloc_hook() at the top of the crash call stack.
The signature indicates an invalid address dereference with low bits of
slab->obj_exts being set. The bits were outside of the range used by
page_memcg_data_flags and objext_flags and hence were not masked out
by slab_obj_exts() when obtaining the pointer stored in slab->obj_exts.
The typical crash log looks like this:
Investigation indicates that these bits are already set when we allocate
slab page and are not zeroed out after allocation. We are not yet sure
why these crashes start happening only recently but regardless of the
reason, not initializing a field that gets used later is wrong. Fix it
by initializing slab->obj_exts during slab page allocation.
Fixes: 21c690a349ba ("mm: introduce slabobj_ext to support slab object extensions") Reported-by: Kent Overstreet <kent.overstreet@linux.dev> Tested-by: Kent Overstreet <kent.overstreet@linux.dev> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Acked-by: Kent Overstreet <kent.overstreet@linux.dev> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250411155737.1360746-1-surenb@google.com Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Darrick J. Wong [Tue, 8 Apr 2025 00:30:30 +0000 (17:30 -0700)]
xfs: compute buffer address correctly in xmbuf_map_backing_mem
Prior to commit e614a00117bc2d, xmbuf_map_backing_mem relied on
folio_file_page to return the base page for the xmbuf's loff_t in the
xfile, and set b_addr to the page_address of that base page.
Now that folio_file_page has been removed from xmbuf_map_backing_mem, we
always set b_addr to the folio_address of the folio. This is correct
for the situation where the folio size matches the buffer size, but it's
totally wrong if tmpfs uses large folios. We need to use
offset_in_folio here.
Found via xfs/801, which demonstrated evidence of corruption of an
in-memory rmap btree block right after initializing an adjacent block.
Fixes: e614a00117bc2d ("xfs: cleanup mapping tmpfs folios into the buffer cache") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Hans Holmberg [Tue, 25 Mar 2025 09:10:49 +0000 (09:10 +0000)]
xfs: add tunable threshold parameter for triggering zone GC
Presently we start garbage collection late - when we start running
out of free zones to backfill max_open_zones. This is a reasonable
default as it minimizes write amplification. The longer we wait,
the more blocks are invalidated and reclaim cost less in terms
of blocks to relocate.
Starting this late however introduces a risk of GC being outcompeted
by user writes. If GC can't keep up, user writes will be forced to
wait for free zones with high tail latencies as a result.
This is not a problem under normal circumstances, but if fragmentation
is bad and user write pressure is high (multiple full-throttle
writers) we will "bottom out" of free zones.
To mitigate this, introduce a zonegc_low_space tunable that lets the
user specify a percentage of how much of the unused space that GC
should keep available for writing. A high value will reclaim more of
the space occupied by unused blocks, creating a larger buffer against
write bursts.
This comes at a cost as write amplification is increased. To
illustrate this using a sample workload, setting zonegc_low_space to
60% avoids high (500ms) max latencies while increasing write
amplification by 15%.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Christoph Hellwig [Thu, 20 Mar 2025 07:52:14 +0000 (08:52 +0100)]
xfs: mark xfs_buf_free as might_sleep()
xfs_buf_free can call vunmap, which can sleep. The vunmap path is an
unlikely one, so add might_sleep to ensure calling xfs_buf_free from
atomic context gets caught more easily.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Christoph Hellwig [Thu, 20 Mar 2025 07:52:13 +0000 (08:52 +0100)]
xfs: remove the leftover xfs_{set,clear}_li_failed infrastructure
Marking a log item as failed kept a buffer reference around for
resubmission of inode and dquote items.
For inode items commit 298f7bec503f3 ("xfs: pin inode backing buffer to
the inode log item") started pinning the inode item buffers
unconditionally and removed the need for this. Later commit acc8f8628c37
("xfs: attach dquot buffer to dquot log item buffer") did the same for
dquot items but didn't fully clean up the xfs_clear_li_failed side
for them. Stop adding the extra pin for dquot items and remove the
helpers.
This happens to fix a call to xfs_buf_free with the AIL lock held,
which would be incorrect for the unlikely case freeing the buffer
ends up calling vfree.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Merge tag 'erofs-for-6.15-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
- Properly handle errors when file-backed I/O fails
- Fix compilation issues on ARM platform (arm-linux-gnueabi)
- Fix parsing of encoded extents
- Minor cleanup
* tag 'erofs-for-6.15-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: remove duplicate code
erofs: fix encoded extents handling
erofs: add __packed annotation to union(__le16..)
erofs: set error to bio if file-backed IO fails
Kent Overstreet [Thu, 10 Apr 2025 01:04:17 +0000 (21:04 -0400)]
bcachefs: Don't print data read retry success on non-errors
We may end up in the data read retry path when reading cached data and
racing with invalidation, or on checksum error when we were reading into
a userspace buffer that might have been modified while the read was in
flight.
These aren't real errors, so we shouldn't print the 'retry success'
message.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Merge tag 'ext4_for_linus-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A few more miscellaneous ext4 bug fixes and cleanups including some
syzbot failures and fixing a stale file handing refeencing an inode
previously used as a regular file, but which has been deleted and
reused as an ea_inode would result in ext4 erroneously considering
this a case of fs corruption"
* tag 'ext4_for_linus-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix off-by-one error in do_split
ext4: make block validity check resistent to sb bh corruption
ext4: avoid -Wflex-array-member-not-at-end warning
Documentation: ext4: Add fields to ext4_super_block documentation
ext4: don't treat fhandle lookup of ea_inode as FS corruption
projects / nvme.git / log