According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].
This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.
If the optional regulator is deferred, we must release some resources.
They will be re-allocated when the probe function will be called again.
Fixes: 6eacf31139bf ("ethernet: arc: Add support for Rockchip SoC layer device tree bindings") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzkaller found an issue caused by lack of sufficient checks
in l2tp_tunnel_create()
RAW sockets can not be considered as UDP ones for instance.
In another patch, we shall replace all pr_err() by less intrusive
pr_debug() so that syzkaller can find other bugs faster. Acked-by: Guillaume Nault <g.nault@alphalink.fr> Acked-by: James Chapman <jchapman@katalix.com>
==================================================================
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
dst_release: dst:00000000d53d0d0f refcnt:-1
Write of size 1 at addr ffff8801d013b798 by task syz-executor3/6242
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following slab-out-of-bounds kasan report in
ndisc_fill_redirect_hdr_option when the incoming ipv6 packet is not
linear and the accessed data are not in the linear data region of orig_skb.
[ 1503.122508] ==================================================================
[ 1503.122832] BUG: KASAN: slab-out-of-bounds in ndisc_send_redirect+0x94e/0x990
[ 1503.123036] Read of size 1184 at addr ffff8800298ab6b0 by task netperf/1932
[ 1503.158698] Memory state around the buggy address:
[ 1503.158816] ffff8800298ab900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.158988] ffff8800298ab980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.159165] >ffff8800298aba00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1503.159338] ^
[ 1503.159436] ffff8800298aba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159610] ffff8800298abb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159785] ==================================================================
[ 1503.159964] Disabling lock debugging due to kernel taint
The test scenario to trigger the issue consists of 4 devices:
- H0: data sender, connected to LAN0
- H1: data receiver, connected to LAN1
- GW0 and GW1: routers between LAN0 and LAN1. Both of them have an
ethernet connection on LAN0 and LAN1
On H{0,1} set GW0 as default gateway while on GW0 set GW1 as next hop for
data from LAN0 to LAN1.
Moreover create an ip6ip6 tunnel between H0 and H1 and send 3 concurrent
data streams (TCP/UDP/SCTP) from H0 to H1 through ip6ip6 tunnel (send
buffer size is set to 16K). While data streams are active flush the route
cache on HA multiple times.
I have not been able to identify a given commit that introduced the issue
since, using the reproducer described above, the kasan report has been
triggered from 4.14 and I have not gone back further.
Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dccp_disconnect() sets 'dp->dccps_hc_tx_ccid' tx handler to NULL,
therefore if DCCP socket is disconnected and dccp_sendmsg() is
called after it, it will cause a NULL pointer dereference in
dccp_write_xmit().
This crash and the reproducer was reported by syzbot. Looks like
it is reproduced if commit 69c64866ce07 ("dccp: CVE-2017-8824:
use-after-free in DCCP code") is applied.
Reported-by: syzbot+f99ab3887ab65d70f816@syzkaller.appspotmail.com Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inet_evict_bucket() iterates global list, and
several tasks may call it in parallel. All of
them hash the same fq->list_evictor to different
lists, which leads to list corruption.
This patch makes fq be hashed to expired list
only if this has not been made yet by another
task. Since inet_frag_alloc() allocates fq
using kmem_cache_zalloc(), we may rely on
list_evictor is initially unhashed.
The problem seems to exist before async
pernet_operations, as there was possible to have
exit method to be executed in parallel with
inet_frags::frags_work, so I add two Fixes tags.
This also may go to stable.
Fixes: d1fe19444d82 "inet: frag: don't re-use chainlist for evictor" Fixes: f84c6821aa54 "net: Convert pernet_subsys, registered from inet_init()" Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrei Vagin reported a KASAN: slab-out-of-bounds error in
skb_update_prio()
Since SYNACK might be attached to a request socket, we need to
get back to the listener socket.
Since this listener is manipulated without locks, add const
qualifiers to sock_cgroup_prioidx() so that the const can also
be used in skb_update_prio()
Also add the const qualifier to sock_cgroup_classid() for consistency.
Fixes: ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrei Vagin <avagin@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A tun device type can trivially be set to arbitrary value using
TUNSETLINK ioctl().
Therefore, lowpan_device_event() must really check that ieee802154_ptr
is not NULL.
Fixes: 2c88b5283f60d ("ieee802154: 6lowpan: remove check on null") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Aring <alex.aring@gmail.com> Cc: Stefan Schmidt <stefan@osg.samsung.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we exceed current packets limit and we have more than one
segment in the list returned by skb_gso_segment(), netem drops
only the first one, skipping the rest, hence kmemleak reports:
Fix it by adding the rest of the segments, if any, to skb 'to_free'
list. Add new __qdisc_drop_all() and qdisc_drop_all() functions
because they can be useful in the future if we need to drop segmented
GSO packets in other places.
Fixes: 6071bd1aa13e ("netem: Segment GSO packets on enqueue") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.
v2: Add Reported-by for syzbot
Fixes: ab7ac4eb9832e32a09f4e804 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com Signed-off-by: Tom Herbert <tom@quantonium.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When inserting duplicate objects (those with the same key),
current rhlist implementation messes up the chain pointers by
updating the bucket pointer instead of prev next pointer to the
newly inserted node. This causes missing elements on removal and
travesal.
Fix that by properly updating pprev pointer to point to
the correct rhash_head next pointer.
Issue: 1241076
Change-Id: I86b2c140bcb4aeb10b70a72a267ff590bb2b17e7 Fixes: ca26893f05e8 ('rhashtable: Add rhlist interface') Signed-off-by: Paul Blakey <paulb@mellanox.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already detect situations where a PPP channel sends packets back to
its upper PPP device. While this is enough to avoid deadlocking on xmit
locks, this doesn't prevent packets from looping between the channel
and the unit.
The problem is that ppp_start_xmit() enqueues packets in ppp->file.xq
before checking for xmit recursion. Therefore, __ppp_xmit_process()
might dequeue a packet from ppp->file.xq and send it on the channel
which, in turn, loops it back on the unit. Then ppp_start_xmit()
queues the packet back to ppp->file.xq and __ppp_xmit_process() picks
it up and sends it again through the channel. Therefore, the packet
will loop between __ppp_xmit_process() and ppp_start_xmit() until some
other part of the xmit path drops it.
For L2TP, we rapidly fill the skb's headroom and pppol2tp_xmit() drops
the packet after a few iterations. But PPTP reallocates the headroom
if necessary, letting the loop run and exhaust the machine resources
(as reported in https://bugzilla.kernel.org/show_bug.cgi?id=199109).
Fix this by letting __ppp_xmit_process() enqueue the skb to
ppp->file.xq, so that we can check for recursion before adding it to
the queue. Now ppp_xmit_process() can drop the packet when recursion is
detected.
__ppp_channel_push() is a bit special. It calls __ppp_xmit_process()
without having any actual packet to send. This is used by
ppp_output_wakeup() to re-enable transmission on the parent unit (for
implementations like ppp_async.c, where the .start_xmit() function
might not consume the skb, leaving it in ppp->xmit_pending and
disabling transmission).
Therefore, __ppp_xmit_process() needs to handle the case where skb is
NULL, dequeuing as many packets as possible from ppp->file.xq.
Reported-by: xu heng <xuheng333@zoho.com> Fixes: 55454a565836 ("ppp: avoid dealock on recursive xmit") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If set/unset mode of the tunnel_key action is not provided, ->init() still
returns 0, and the caller proceeds with bogus 'struct tc_action *' object,
this results in crash:
% tc actions add action tunnel_key src_ip 1.1.1.1 dst_ip 2.2.2.1 id 7 index 1
Fixes: d0f6dd8a914f ("net/sched: Introduce act_tunnel_key") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 664fcf123a30e (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.
With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Signed-off-by: Brad Mouring <brad.mouring@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 9ffcc3725f09 ("mlxsw: spectrum: Allow packets to be trapped
from any PG") I fixed a problem where packets could not be trapped to
the CPU due to exceeded shared buffer quotas. The mentioned commit
explains the problem in detail.
The problem was fixed by assigning a minimum quota for the CPU port and
the traffic class used for scheduling traffic to the CPU.
However, commit 117b0dad2d54 ("mlxsw: Create a different trap group list
for each device") assigned different traffic classes to different
packet types and rendered the fix useless.
Fix the problem by assigning a minimum quota for the CPU port and all
the traffic classes that are currently in use.
Fixes: 117b0dad2d54 ("mlxsw: Create a different trap group list for each device") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Eddie Shklaer <eddies@mellanox.com> Tested-by: Eddie Shklaer <eddies@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using seg6 in encap mode, we call ipv6_dev_get_saddr() to set the
source address of the outer IPv6 header, in case none was specified.
Using skb->dev can lead to BUG() when it is in an inconsistent state.
This patch uses the net_device attached to the skb's dst instead.
Fixes: 6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Reported-by: Tom Herbert <tom@quantonium.net> Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 2f987a76a977 ("net: ipv6: keep sk status consistent after datagram connect failure") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On unsuccesful ip6_datagram_connect(), if the failure is caused by
ip6_datagram_dst_update(), the sk peer information are cleared, but
the sk->sk_state is preserved.
If the socket was already in an established status, the overall sk
status is inconsistent and fouls later checks in datagram code.
Fix this saving the old peer information and restoring them in
case of failure. This also aligns ipv6 datagram connect() behavior
with ipv4.
v1 -> v2:
- added missing Fixes tag
Fixes: 85cb73ff9b74 ("net: ipv6: reset daddr and dport in sk if connect() fails") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding a macvlan device on top of a lowerdev that supports
the xfrm offloads fails with a new regression:
# ip link add link ens1f0 mv0 type macvlan
RTNETLINK answers: Operation not permitted
Tracing down the failure shows that the macvlan device inherits
the NETIF_F_HW_ESP and NETIF_F_HW_ESP_TX_CSUM feature flags
from the lowerdev, but with no dev->xfrmdev_ops API filled
in, it doesn't actually support xfrm. When the request is
made to add the new macvlan device, the XFRM listener for
NETDEV_REGISTER calls xfrm_api_check() which fails the new
registration because dev->xfrmdev_ops is NULL.
The macvlan creation succeeds when we filter out the ESP
feature flags in macvlan_fix_features(), so let's filter them
out like we're already filtering out ~NETIF_F_NETNS_LOCAL.
When XFRM support is added in the future, we can add the flags
into MACVLAN_FEATURES.
This same problem could crop up in the future with any other
new feature flags, so let's filter out any flags that aren't
defined as supported in macvlan.
Fixes: d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API") Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code performs unneeded free. Remove the redundant skb freeing
during the error path.
Fixes: 1555d204e743 ("devlink: Support for pipeline debug (dpipe)") Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ethernet drivers (like TI CPSW) may connect and manage >1 Net PHYs per
one netdevice, as result such drivers will produce warning during system
boot and fail to connect second phy to netdevice when PHYLIB framework
will try to create sysfs link netdev->phydev for second PHY
in phy_attach_direct(), because sysfs link with the same name has been
created already for the first PHY. As result, second CPSW external
port will became unusable.
Fix it by relaxing error checking when PHYLIB framework is creating sysfs
link netdev->phydev in phy_attach_direct(), suppressing warning by using
sysfs_create_link_nowarn() and adding error message instead.
After this change links (phy->netdev and netdev->phy) creation failure is not
fatal any more and system can continue working, which fixes TI CPSW issue.
Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Fixes: a3995460491d ("net: phy: Relax error checking on sysfs_create_link()") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs_create_link_nowarn() is going to be used in phylib framework in
subsequent patch which can be built as module. Hence, export
sysfs_create_link_nowarn() to avoid build errors.
Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Fixes: a3995460491d ("net: phy: Relax error checking on sysfs_create_link()") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FW workaround. The iWARP LL2 connection did not expect TCP packets
to arrive on it's connection. The fix drops any non-tcp packets
Fixes b5c29ca ("qed: iWARP CM - setup a ll2 connection for handling
SYN packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the connection is aborted, there is no point in
keeping the packets on the write queue until the connection
is closed.
Similar to a27fd7a8ed38 ('tcp: purge write queue upon RST'),
this is essential for a correct MSG_ZEROCOPY implementation,
because userspace cannot call close(fd) before receiving
zerocopy signals even when the connection is aborted.
Fixes: f214f915e7db ("tcp: enable MSG_ZEROCOPY") Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcp_write_queue_purge clears all the SKBs in the write queue
but does not reset the sk_send_head. As a result, we can have
a NULL pointer dereference anywhere that we use tcp_send_head
instead of the tcp_write_queue_tail.
For example, after a27fd7a8ed38 (tcp: purge write queue upon RST),
we can purge the write queue on RST. Prior to 75c119afe14f (tcp: implement rb-tree based retransmit queue),
tcp_push will only check tcp_send_head and then accesses
tcp_write_queue_tail to send the actual SKB. As a result, it will
dereference a NULL pointer.
This has been reported twice for 4.14 where we don't have 75c119afe14f:
In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).
One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current check statement in BPF syscall will do a capability check
for CAP_SYS_ADMIN before checking sysctl_unprivileged_bpf_disabled. This
code path will trigger unnecessary security hooks on capability checking
and cause false alarms on unprivileged process trying to get CAP_SYS_ADMIN
access. This can be resolved by simply switch the order of the statement
and CAP_SYS_ADMIN is not required anyway if unprivileged bpf syscall is
allowed.
Signed-off-by: Chenbo Feng <fengc@google.com> Acked-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prasad reported that he has seen crashes in BPF subsystem with netd
on Android with arm64 in the form of (note, the taint is unrelated):
[ 4134.721483] Unable to handle kernel paging request at virtual address 800000001
[ 4134.820925] Mem abort info:
[ 4134.901283] Exception class = DABT (current EL), IL = 32 bits
[ 4135.016736] SET = 0, FnV = 0
[ 4135.119820] EA = 0, S1PTW = 0
[ 4135.201431] Data abort info:
[ 4135.301388] ISV = 0, ISS = 0x00000021
[ 4135.359599] CM = 0, WnR = 0
[ 4135.470873] user pgtable: 4k pages, 39-bit VAs, pgd = ffffffe39b946000
[ 4135.499757] [0000000800000001] *pgd=0000000000000000, *pud=0000000000000000
[ 4135.660725] Internal error: Oops: 96000021 [#1] PREEMPT SMP
[ 4135.674610] Modules linked in:
[ 4135.682883] CPU: 5 PID: 1260 Comm: netd Tainted: G S W 4.14.19+ #1
[ 4135.716188] task: ffffffe39f4aa380 task.stack: ffffff801d4e0000
[ 4135.731599] PC is at bpf_prog_add+0x20/0x68
[ 4135.741746] LR is at bpf_prog_inc+0x20/0x2c
[ 4135.751788] pc : [<ffffff94ab7ad584>] lr : [<ffffff94ab7ad638>] pstate: 60400145
[ 4135.769062] sp : ffffff801d4e3ce0
[...]
[ 4136.258315] Process netd (pid: 1260, stack limit = 0xffffff801d4e0000)
[ 4136.273746] Call trace:
[...]
[ 4136.442494] 3ca0: ffffff94ab7ad5840000000060400145ffffffe3a01bf8f80000000000000006
[ 4136.460936] 3cc0: 0000008000000000ffffff94ab844204ffffff801d4e3cf0ffffff94ab7ad584
[ 4136.479241] [<ffffff94ab7ad584>] bpf_prog_add+0x20/0x68
[ 4136.491767] [<ffffff94ab7ad638>] bpf_prog_inc+0x20/0x2c
[ 4136.504536] [<ffffff94ab7b5d08>] bpf_obj_get_user+0x204/0x22c
[ 4136.518746] [<ffffff94ab7ade68>] SyS_bpf+0x5a8/0x1a88
Android's netd was basically pinning the uid cookie BPF map in BPF
fs (/sys/fs/bpf/traffic_cookie_uid_map) and later on retrieving it
again resulting in above panic. Issue is that the map was wrongly
identified as a prog! Above kernel was compiled with clang 4.0,
and it turns out that clang decided to merge the bpf_prog_iops and
bpf_map_iops into a single memory location, such that the two i_ops
could then not be distinguished anymore.
Reason for this miscompilation is that clang has the more aggressive
-fmerge-all-constants enabled by default. In fact, clang source code
has a comment about it in lib/AST/ExprConstant.cpp on why it is okay
to do so:
Pointers with different bases cannot represent the same object.
(Note that clang defaults to -fmerge-all-constants, which can
lead to inconsistent results for comparisons involving the address
of a constant; this generally doesn't matter in practice.)
The issue never appeared with gcc however, since gcc does not enable
-fmerge-all-constants by default and even *explicitly* states in
it's option description that using this flag results in non-conforming
behavior, quote from man gcc:
Languages like C or C++ require each variable, including multiple
instances of the same variable in recursive calls, to have distinct
locations, so using this option results in non-conforming behavior.
There are also various clang bug reports open on that matter [1],
where clang developers acknowledge the non-conforming behavior,
and refer to disabling it with -fno-merge-all-constants. But even
if this gets fixed in clang today, there are already users out there
that triggered this. Thus, fix this issue by explicitly adding
-fno-merge-all-constants to the kernel's Makefile to generically
disable this optimization, since potentially other places in the
kernel could subtly break as well.
Note, there is also a flag called -fmerge-constants (not supported
by clang), which is more conservative and only applies to strings
and it's enabled in gcc's -O/-O2/-O3/-Os optimization levels. In
gcc's code, the two flags -fmerge-{all-,}constants share the same
variable internally, so when disabling it via -fno-merge-all-constants,
then we really don't merge any const data (e.g. strings), and text
size increases with gcc (14,927,214 -> 14,942,646 for vmlinux.o).
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Since commit 204f672255c2 ("staging: android: ion: Use CMA APIs directly")
the CMA API is now used directly and therefore the allocated memory is no
longer automatically zeroed.
Explicitly zero CMA allocated memory to ensure that no data is exposed to
userspace.
Fixes: 204f672255c2 ("staging: android: ion: Use CMA APIs directly") Signed-off-by: Liam Mark <lmark@codeaurora.org> Acked-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of CHAs is miscalculated on multi-domain PCI Skylake server systems,
resulting in an uncore driver initialization error.
Gary Kroening explains:
"For systems with a single PCI segment, it is sufficient to look for the
bus number to change in order to determine that all of the CHa's have
been counted for a single socket.
However, for multi PCI segment systems, each socket is given a new
segment and the bus number does NOT change. So looking only for the
bus number to change ends up counting all of the CHa's on all sockets
in the system. This leads to writing CPU MSRs beyond a valid range and
causes an error in ivbep_uncore_msr_init_box()."
To fix this bug, query the number of CHAs from the CAPID6 register:
it should read bits 27:0 in the CAPID6 register located at
Device 30, Function 3, Offset 0x9C. These 28 bits form a bit vector
of available LLC slices and the CHAs that manage those slices.
Reported-by: Kroening, Gary <gary.kroening@hpe.com> Tested-by: Kroening, Gary <gary.kroening@hpe.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: abanman@hpe.com Cc: dimitri.sivanich@hpe.com Cc: hpa@zytor.com Cc: mike.travis@hpe.com Cc: russ.anderson@hpe.com Fixes: cd34cd97b7b4 ("perf/x86/intel/uncore: Add Skylake server uncore support") Link: http://lkml.kernel.org/r/1520967094-13219-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We intended to clear the lowest 6 bits but because of a type bug we
clear the high 32 bits as well. Andi says that periods are rarely more
than U32_MAX so this bug probably doesn't have a huge runtime impact.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: 294fe0f52a44 ("perf/x86/intel: Add INST_RETIRED.ALL workarounds") Link: http://lkml.kernel.org/r/20180317115216.GB4035@mwanda Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ctx_resched(), EVENT_FLEXIBLE should be sched_out when EVENT_PINNED is
added. However, ctx_resched() calculates ctx_event_type before checking
this condition. As a result, pinned events will NOT get higher priority
than flexible events.
The following shows this issue on an Intel CPU (where ref-cycles can
only use one hardware counter).
1. First start:
perf stat -C 0 -e ref-cycles -I 1000
2. Then, in the second console, run:
perf stat -C 0 -e ref-cycles:D -I 1000
The second perf uses pinned events, which is expected to have higher
priority. However, because it failed in ctx_resched(). It is never
run.
This patch fixes this by calculating ctx_event_type after re-evaluating
event_type.
Reported-by: Ephraim Park <ephiepark@fb.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <jolsa@redhat.com> Cc: <kernel-team@fb.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: 487f05e18aa4 ("perf/core: Optimize event rescheduling on active contexts") Link: http://lkml.kernel.org/r/20180306055504.3283731-1-songliubraving@fb.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vk cts test:
dEQP-VK.api.external.semaphore.opaque_fd.export_multiple_times_temporary
triggers a lot of
VFS: Close: file count is 0
Dave pointed out that clearing the syncobj->file from
drm_syncobj_file_release() was sufficient to silence the test, but that
opens a can of worm since we assumed that the syncobj->file was never
unset. Stop trying to reuse the same struct file for every fd pointing
to the drm_syncobj, and allocate one file for each fd instead.
v2: Fixup return handling of drm_syncobj_fd_to_handle
v2.1: [airlied: fix possible syncobj ref race]
v2.2: [jekstrand: back-port to 4.14]
Reported-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Dave Airlie <airlied@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Jason Ekstrand <jason@jlekstrand.net> Tested-by: Clayton Craft <clayton.a.craft@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Binutils 2.31 will enable -z separate-code by default for x86 to avoid
mixing code pages with data to improve cache performance as well as
security. To reduce x86-64 executable and shared object sizes, the
maximum page size is reduced from 2MB to 4KB. But x86-64 kernel must
be aligned to 2MB. Pass -z max-page-size=0x200000 to linker to force
2MB page size regardless of the default page size used by linker.
Tested with Linux kernel 4.15.6 on x86-64.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/CAMe9rOp4_%3D_8twdpTyAP2DhONOCeaTOsniJLoppzhoNptL8xzA@mail.gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The undocumented 'icebp' instruction (aka 'int1') works pretty much like
'int3' in the absense of in-circuit probing equipment (except,
obviously, that it raises #DB instead of raising #BP), and is used by
some validation test-suites as such.
But Andy Lutomirski noticed that his test suite acted differently in kvm
than on bare hardware.
The reason is that kvm used an inexact test for the icebp instruction:
it just assumed that an all-zero VM exit qualification value meant that
the VM exit was due to icebp.
That is not unlike the guess that do_debug() does for the actual
exception handling case, but it's purely a heuristic, not an absolute
rule. do_debug() does it because it wants to ascribe _some_ reasons to
the #DB that happened, and an empty %dr6 value means that 'icebp' is the
most likely casue and we have no better information.
But kvm can just do it right, because unlike the do_debug() case, kvm
actually sees the real reason for the #DB in the VM-exit interruption
information field.
So instead of relying on an inexact heuristic, just use the actual VM
exit information that says "it was 'icebp'".
Right now the 'icebp' instruction isn't technically documented by Intel,
but that will hopefully change. The special "privileged software
exception" information _is_ actually mentioned in the Intel SDM, even
though the cause of it isn't enumerated.
Reported-by: Andy Lutomirski <luto@kernel.org> Tested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clockid argument of clockid_to_kclock() comes straight from user space
via various syscalls and is used as index into the posix_clocks array.
Protect it against spectre v1 array out of bounds speculation. Remove the
redundant check for !posix_clock[id] as this is another source for
speculation and does not provide any advantage over the return
posix_clock[id] path which returns NULL in that case anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: David Woodhouse <dwmw@amazon.co.uk> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1802151718320.1296@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
glibc keeps getting cleverer, and my version now turns raise() into
more than one syscall. Since the test relies on ptrace seeing an
exact set of syscalls, this breaks the test. Replace raise(SIGSTOP)
with syscall(SYS_tgkill, ...) to force glibc to get out of our way.
There's nothing IST-worthy about #BP/int3. We don't allow kprobes
in the small handful of places in the kernel that run at CPL0 with
an invalid stack, and 32-bit kernels have used normal interrupt
gates for #BP forever.
Furthermore, we don't allow kprobes in places that have usergs while
in kernel mode, so "paranoid" is also unnecessary.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While waiting for the TX object to send an RTR, an external message with a
matching id can overwrite the TX data. In this case we must call the rx
routine and then try transmitting the message that was overwritten again.
The queue was being stalled because the RX event did not generate an
interrupt to wake up the queue again and the TX event did not happen
because the TXRQST flag is reset by the chip when new data is received.
According to the CC770 datasheet the id of a message object should not be
changed while the MSGVAL bit is set. This has been fixed by resetting the
MSGVAL bit before modifying the object in the transmit function and setting
it after. It is not enough to set & reset CPUUPD.
It is important to keep the MSGVAL bit reset while the message object is
being modified. Otherwise, during RTR transmission, a frame with matching
id could trigger an rx-interrupt, which would cause a race condition
between the interrupt routine and the transmit function.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com> Tested-by: Richard Weinberger <richard@nod.at> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older versions of the core are not compatible with the driver due
to various intrusive fixes of the core. Read out the VER register,
check the core revision bitfield and verify if the core in use is
new enough (rev 2.1 or newer) to work correctly with this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Markus Marb <markus@marb.org> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new version of the IFI CANFD core has significantly less complex
error state indication logic. In particular, the warning/error state
bits are no longer all over the place, but are all present in the
STATUS register. Moreover, there is a new IRQ register bit indicating
transition between error states (active/warning/passive/busoff).
This patch makes use of this bit to weed out the obscure selective
INTERRUPT register clearing, which was used to carry over the error
state indication into the poll function. While at it, this patch
fixes the handling of the ACTIVE state, since the hardware provides
indication of the core being in ACTIVE state and that in turn fixes
the state transition indication toward userspace. Finally, register
reads in the poll function are moved to the matching subfunctions
since those are also no longer needed in the poll function.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Markus Marb <markus@marb.org> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an interface starts, the echo_skb array is empty and the network
queue should be started only. This patch replaces useless code and locks
when the internal RX_BARRIER message is received from the IP core, telling
the driver that tx may start.
This patch makes atomic the handling of the linux-can echo_skb array and
the network tx queue. This prevents from the "BUG! echo_skb is occupied!"
message to be printed by the linux-can core, in SMP environments.
If the server is malicious then *bytes_read could be larger than the
size of the "target" buffer. It would lead to memory corruption when we
do the memcpy().
Reported-by: Dr Silvio Cesare of InfoSect <Silvio Cesare <silvio.cesare@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Number of ECC status registers i.e. (ECCSTATx) has been increased in IFC
version 2.0.0 due to increase in SRAM size. This is causing eccstat
array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Section was not properly computed. The value of OOB region definition is
always ECC section 0 information in the OOB area, but we want to get all
the ECC bytes information, so we should call
mtd_ooblayout_ecc(mtd, section++, &oobregion) until it returns -ERANGE.
Fixes: c2b78452a9db ("mtd: use mtd_ooblayout_xxx() helpers where appropriate") Cc: <stable@vger.kernel.org> Signed-off-by: OuYang ZhiZhong <ouyzz@yealink.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
@SYM[+|-offs] : Fetch memory at SYM +|- offs (SYM should be a data symbol)
However, the parser doesn't parse minus offset correctly, since
commit 2fba0c8867af ("tracing/kprobes: Fix probe offset to be
unsigned") drops minus ("-") offset support for kprobe probe
address usage.
This fixes the traceprobe_split_symbol_offset() to parse minus
offset again with checking the offset range, and add a minus
offset check in kprobe probe address usage.
Link: http://lkml.kernel.org/r/152129028983.31874.13419301530285775521.stgit@devbox Cc: Ingo Molnar <mingo@redhat.com> Cc: Tom Zanussi <tom.zanussi@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Fixes: 2fba0c8867af ("tracing/kprobes: Fix probe offset to be unsigned") Acked-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c713fb071edc ("rtlwifi: rtl8821ae: Fix connection lost problem
correctly") a problem in rtl8821ae that caused loss of signal was fixed.
That same problem has now been reported for rtl8723be. Accordingly,
the ASPM L1 latency has been increased from 0 to 7 to fix the instability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Tested-by: James Cameron <quozl@laptop.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware has a requirement that the P2P_DEVICE address should
be different from the address of the primary interface. When not
specified by user-space, the driver generates the MAC address for
the P2P_DEVICE interface using the MAC address of the primary
interface and setting the locally administered bit. However, the MAC
address of the primary interface may already have that bit set causing
the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this
by using a random address instead to determine the P2P_DEVICE address.
Cc: stable@vger.kernel.org # 3.10.y Reported-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to 25520d55cdb6 ("block: Inline blk_integrity in struct gendisk")
we needed to temporarily add a zero-capacity disk before registering for
blk-integrity. But adding a zero-capacity disk caused the partition
table scanning to bail early, and this resulted in partitions not coming
up after a probe of the BTT or blk namespaces.
We can now register for integrity before the disk has been added, and
this fixes the rescan problems.
Fixes: 25520d55cdb6 ("block: Inline blk_integrity in struct gendisk") Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The resource allocation in WDAT watchdog has off-one-by error, it sets
one byte more than the actual end address. This may eventually lead
to unexpected resource conflicts.
Fixes: 058dfc767008 (ACPI / watchdog: Add support for WDAT hardware watchdog) Cc: 4.9+ <stable@vger.kernel.org> # 4.9+ Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 99759869faf1 "acpi: Add acpi_map_pxm_to_online_node()" added
support for mapping a given proximity to its nearest, by SLIT distance,
online node. However, it sometimes returns unexpected results due to the
fact that it switches from comparing the PXM node to the last node that
was closer than the current max.
for_each_online_node(n) {
dist = node_distance(node, n);
if (dist < min_dist) {
min_dist = dist;
node = n; <---- from this point we're using the
wrong node for node_distance()
Fixes: 99759869faf1 ("acpi: Add acpi_map_pxm_to_online_node()") Cc: <stable@vger.kernel.org> Reviewed-by: Toshi Kani <toshi.kani@hp.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 726d061fbd36 ("mm: vmscan: kick flushers when we encounter dirty
pages on the LRU") added flusher invocation to shrink_inactive_list()
when many dirty pages on the LRU are encountered.
However, shrink_inactive_list() doesn't wake up flushers for legacy
cgroup reclaim, so the next commit bbef938429f5 ("mm: vmscan: remove old
flusher wakeup from direct reclaim path") removed the only source of
flusher's wake up in legacy mem cgroup reclaim path.
This leads to premature OOM if there is too many dirty pages in cgroup:
# mkdir /sys/fs/cgroup/memory/test
# echo $$ > /sys/fs/cgroup/memory/test/tasks
# echo 50M > /sys/fs/cgroup/memory/test/memory.limit_in_bytes
# dd if=/dev/zero of=tmp_file bs=1M count=100
Killed
The memmap options sent to the udl framebuffer driver were not being
checked for all sets of possible crazy values. Fix this up by properly
bounding the allowed values.
getfb can only return a single plane, so reject attempts to use it with
multi-plane framebuffers.
Signed-off-by: Daniel Stone <daniels@collabora.com> Reported-by: Daniel van Vugt <daniel.van.vugt@canonical.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Fixes: 308e5bcbdb10 ("drm: add an fb creation ioctl that takes a pixel format v5") Cc: stable@vger.kernel.org # v3.3+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105518 Link: https://patchwork.freedesktop.org/patch/msgid/20180320225839.30905-1-daniels@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When validating legacy surfaces, the backup bo might be destroyed at
surface validate time. However, the kms resource validation code may have
the bo reserved, so we will destroy a locked mutex. While there shouldn't
be any other users of that mutex when it is destroyed, it causes a lock
leak and thus throws a lockdep error.
Fix this by having the kms resource validation code hold a reference to
the bo while we have it reserved. We do this by introducing a validation
context which might come in handy when the kms code is extended to validate
multiple resources or buffers.
Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we are running without fbdev, transitioning from the login screen to
X or gnome-shell/wayland will cause a vt switch and the driver will disable
svga mode, losing all modesetting resources. However, the kms atomic state
does not reflect that and may think that a crtc is still turned on, which
will cause device errors when we try to bind an fb to the crtc, and the
screen will remain black.
Fix this by turning off all kms resources before disabling svga mode.
This reverts commit b92df1de5d28 ("mm: page_alloc: skip over regions of
invalid pfns where possible"). The commit is meant to be a boot init
speed up skipping the loop in memmap_init_zone() for invalid pfns.
But given some specific memory mapping on x86_64 (or more generally
theoretically anywhere but on arm with CONFIG_HAVE_ARCH_PFN_VALID) the
implementation also skips valid pfns which is plain wrong and causes
'kernel BUG at mm/page_alloc.c:1389!'
Replace lock_page() with trylock_page() and skip the page if we failed
to lock it. We will get to the page on the next scan.
We can test for the PageTransHuge() outside the page lock as we only
need protection against splitting the page under us. Holding pin oni
the page is enough for this.
Link: http://lkml.kernel.org/r/20180316210830.43738-1-kirill.shutemov@linux.intel.com Fixes: 779750d20b93 ("shmem: split huge pages beyond i_size under memory pressure") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Eric Wheeler <linux-mm@lists.ewheeler.net> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> [4.8+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
khugepaged is not yet able to convert PTE-mapped huge pages back to PMD
mapped. We do not collapse such pages. See check
khugepaged_scan_pmd().
But if between khugepaged_scan_pmd() and __collapse_huge_page_isolate()
somebody managed to instantiate THP in the range and then split the PMD
back to PTEs we would have a problem --
VM_BUG_ON_PAGE(PageCompound(page)) will get triggered.
It's possible since we drop mmap_sem during collapse to re-take for
write.
Replace the VM_BUG_ON() with graceful collapse fail.
Link: http://lkml.kernel.org/r/20180315152353.27989-1-kirill.shutemov@linux.intel.com Fixes: b1caa957ae6d ("khugepaged: ignore pmd tables with THP mapped with ptes") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On architectures with CONFIG_HAVE_ARCH_HUGE_VMAP set, ioremap() may
create pud/pmd mappings. A kernel panic was observed on arm64 systems
with Cortex-A75 in the following steps as described by Hanjun Guo.
1. ioremap a 4K size, valid page table will build,
2. iounmap it, pte0 will set to 0;
3. ioremap the same address with 2M size, pgd/pmd is unchanged,
then set the a new value for pmd;
4. pte0 is leaked;
5. CPU may meet exception because the old pmd is still in TLB,
which will lead to kernel panic.
This panic is not reproducible on x86. INVLPG, called from iounmap,
purges all levels of entries associated with purged address on x86. x86
still has memory leak.
The patch changes the ioremap path to free unmapped page table(s) since
doing so in the unmap path has the following issues:
- The iounmap() path is shared with vunmap(). Since vmap() only
supports pte mappings, making vunmap() to free a pte page is an
overhead for regular vmap users as they do not need a pte page freed
up.
- Checking if all entries in a pte page are cleared in the unmap path
is racy, and serializing this check is expensive.
- The unmap path calls free_vmap_area_noflush() to do lazy TLB purges.
Clearing a pud/pmd entry before the lazy TLB purges needs extra TLB
purge.
Add two interfaces, pud_free_pmd_page() and pmd_free_pte_page(), which
clear a given pud/pmd entry and free up a page for the lower level
entries.
This patch implements their stub functions on x86 and arm64, which work
as workaround.
[akpm@linux-foundation.org: fix typo in pmd_free_pte_page() stub] Link: http://lkml.kernel.org/r/20180314180155.19492-2-toshi.kani@hpe.com Fixes: e61ce6ade404e ("mm: change ioremap to set up huge I/O mappings") Reported-by: Lei Li <lious.lilei@hisilicon.com> Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Wang Xuefeng <wxf.wang@hisilicon.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Borislav Petkov <bp@suse.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Chintan Pandya <cpandya@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A vma with vm_pgoff large enough to overflow a loff_t type when
converted to a byte offset can be passed via the remap_file_pages system
call. The hugetlbfs mmap routine uses the byte offset to calculate
reservations and file size.
The overflowed pgoff value causes hugetlbfs to try to set up a mapping
with a negative range (end < start) that leaves invalid state which
causes the BUG.
The previous overflow fix to this code was incomplete and did not take
the remap_file_pages system call into account.
[mike.kravetz@oracle.com: v3] Link: http://lkml.kernel.org/r/20180309002726.7248-1-mike.kravetz@oracle.com
[akpm@linux-foundation.org: include mmdebug.h]
[akpm@linux-foundation.org: fix -ve left shift count on sh] Link: http://lkml.kernel.org/r/20180308210502.15952-1-mike.kravetz@oracle.com Fixes: 045c7a3f53d9 ("hugetlbfs: fix offset overflow in hugetlbfs mmap") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reported-by: Nic Losby <blurbdust@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had some reports of panics in nfsd4_lm_notify, and that showed a
nfs4_lockowner that had outlived its so_client.
Ensure that we walk any leftover lockowners after tearing down all of
the stateids, and remove any blocked locks that they hold.
With this change, we also don't need to walk the nbl_lru on nfsd_net
shutdown, as that will happen naturally when we tear down the clients.
Fixes: 76d348fadff5 (nfsd: have nfsd4_lock use blocking locks for v4.1+ locks) Reported-by: Frank Sorenson <fsorenso@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Cc: stable@vger.kernel.org # 4.9 Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A domain cgroup isn't allowed to be turned threaded if its subtree is
populated or domain controllers are enabled. cgroup_enable_threaded()
depended on cgroup_can_be_thread_root() test to enforce this rule. A
parent which has populated domain descendants or have domain
controllers enabled can't become a thread root, so the above rules are
enforced automatically.
However, for the root cgroup which can host mixed domain and threaded
children, cgroup_can_be_thread_root() doesn't check any of those
conditions and thus first level cgroups ends up escaping those rules.
This patch fixes the bug by adding explicit checks for those rules in
cgroup_enable_threaded().
When commit 9c7be59fc519af ("libata: Apply NOLPM quirk to Crucial MX100
512GB SSDs") was added it inherited the ATA_HORKAGE_NO_NCQ_TRIM quirk
from the existing "Crucial_CT*MX100*" entry, but that entry sets model_rev
to "MU01", where as the entry adding the NOLPM quirk sets it to NULL.
This means that after this commit we no apply the NO_NCQ_TRIM quirk to
all "Crucial_CT512MX100*" SSDs even if they have the fixed "MU02"
firmware. This commit splits the "Crucial_CT512MX100*" quirk into 2
quirks, one for the "MU01" firmware and one for all other firmware
versions, so that we once again only apply the NO_NCQ_TRIM quirk to the
"MU01" firmware version.
Fixes: 9c7be59fc519af ("libata: Apply NOLPM quirk to ... MX100 512GB SSDs") Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b17e5729a630 ("libata: disable LPM for Crucial BX100 SSD 500GB
drive"), introduced a ATA_HORKAGE_NOLPM quirk for Crucial BX100 500GB SSDs
but limited this to the MU02 firmware version, according to:
http://www.crucial.com/usa/en/support-ssd-firmware
MU02 is the last version, so there are no newer possibly fixed versions
and if the MU02 version has broken LPM then the MU01 almost certainly
also has broken LPM, so this commit changes the quirk to apply to all
firmware versions.
Fixes: b17e5729a630 ("libata: disable LPM for Crucial BX100 SSD 500GB...") Cc: stable@vger.kernel.org Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been reports of the Crucial M500 480GB model not working
with LPM set to min_power / med_power_with_dipm level.
It has not been tested with medium_power, but that typically has no
measurable power-savings.
Note the reporters Crucial_CT480M500SSD3 has a firmware version of MU03
and there is a MU05 update available, but that update does not mention any
LPM fixes in its changelog, so the quirk matches all firmware versions.
In my experience the LPM problems with (older) Crucial SSDs seem to be
limited to higher capacity versions of the SSDs (different firmware?),
so this commit adds a NOLPM quirk for the 480 and 960GB versions of the
M500, to avoid LPM causing issues with these SSDs.
Cc: stable@vger.kernel.org Reported-and-tested-by: Martin Steigerwald <martin@lichtvoll.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samsung explicitly states that queued TRIM is supported for Linux with
860 PRO and 860 EVO.
Make the previous blacklist to cover only 840 and 850 series.
Signed-off-by: Park Ju Hyung <qkrwngud825@gmail.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various people have reported the Crucial MX100 512GB model not working
with LPM set to min_power. I've now received a report that it also does
not work with the new med_power_with_dipm level.
It does work with medium_power, but that has no measurable power-savings
and given the amount of people being bitten by the other levels not
working, this commit just disables LPM altogether.
Note all reporters of this have either the 512GB model (max capacity), or
are not specifying their SSD's size. So for now this quirk assumes this is
a problem with the 512GB model only.
syzkaller hit a WARN() in ata_bmdma_qc_issue() when writing to /dev/sg0.
This happened because it issued an ATA pass-through command (ATA_16)
where the protocol field indicated that NCQ should be used -- but the
device did not support NCQ.
We could just remove the WARN() from libata-sff.c, but the real problem
seems to be that the SCSI -> ATA translation code passes through NCQ
commands without verifying that the device actually supports NCQ.
Fix this by adding the appropriate check to ata_scsi_pass_thru().
Here's reproducer that works in QEMU when /dev/sg0 refers to a disk of
the default type ("82371SB PIIX3 IDE"):
syzkaller reported a crash in ata_bmdma_fill_sg() when writing to
/dev/sg1. The immediate cause was that the ATA command's scatterlist
was not DMA-mapped, which causes 'pi - 1' to underflow, resulting in a
write to 'qc->ap->bmdma_prd[0xffffffff]'.
Strangely though, the flag ATA_QCFLAG_DMAMAP was set in qc->flags. The
root cause is that when __ata_scsi_queuecmd() is preparing to relay a
SCSI command to an ATAPI device, it doesn't correctly validate the CDB
length before copying it into the 16-byte buffer 'cdb' in 'struct
ata_queued_cmd'. Namely, it validates the fixed CDB length expected
based on the SCSI opcode but not the actual CDB length, which can be
larger due to the use of the SG_NEXT_CMD_LEN ioctl. Since 'flags' is
the next member in ata_queued_cmd, a buffer overflow corrupts it.
Fix it by requiring that the actual CDB length be <= 16 (ATAPI_CDB_LEN).
[Really it seems the length should be required to be <= dev->cdb_len,
but the current behavior seems to have been intentionally introduced by
commit 607126c2a21c ("libata-scsi: be tolerant of 12-byte ATAPI commands
in 16-byte CDBs") to work around a userspace bug in mplayer. Probably
the workaround is no longer needed (mplayer was fixed in 2007), but
continuing to allow lengths to up 16 appears harmless for now.]
Here's a reproducer that works in QEMU when /dev/sg1 refers to the
CD-ROM drive that qemu-system-x86_64 creates by default:
The Atheros 1525/QCA6174 BT doesn't seem working properly on the
recent kernels, as it tries to load a wrong firmware
ar3k/AthrBT_0x00000200.dfu and it fails.
This seems to have been a problem for some time, and the known
workaround is to apply BTUSB_QCA_ROM quirk instead of BTUSB_ATH3012.
The issue can be reproduced before commit fd865802c66b ("Bluetooth:
btusb: fix QCA Rome suspend/resume") gets introduced, so the reset
resume quirk is still needed for this system.
Commit 1fdb92697469 ("Bluetooth: btusb: Use DMI matching for QCA
reset_resume quirking"), added the Lenovo Yoga 920 to the
btusb_needs_reset_resume_table.
Testing has shown that this is a false positive and the problems where
caused by issues with the initial fix: commit fd865802c66b ("Bluetooth:
btusb: fix QCA Rome suspend/resume"), which has already been reverted.
So the QCA Rome BT in the Yoga 920 does not need a reset-resume quirk at
all and this commit removes it from the btusb_needs_reset_resume_table.
Note that after this commit the btusb_needs_reset_resume_table is now
empty. It is kept around on purpose, since this whole series of commits
started for a reason and there are actually broken platforms around,
which need to be added to it.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 1fdb92697469 ("Bluetooth: btusb: Use DMI matching for QCA ...") Cc: stable@vger.kernel.org Cc: Brian Norris <briannorris@chromium.org> Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Kevin Fenzi <kevin@scrye.com> Suggested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver uses alias from Device Tree as an index of pin controller data
array. In case of a wrong DTB or an out-of-tree DTB, the alias could be
outside of this data array leading to out-of-bounds access.
Depending on binary and memory layout, this could be handled properly
(showing error like "samsung-pinctrl 3860000.pinctrl: driver data not
available") or could lead to exceptions.
Fix bugs in signaling the Hyper-V host when freeing space in the
host->guest ring buffer:
1. The interrupt_mask must not be used to determine whether to signal
on the host->guest ring buffer
2. The ring buffer write_index must be read (via hv_get_bytes_to_write)
*after* pending_send_sz is read in order to avoid a race condition
3. Comparisons with pending_send_sz must treat the "equals" case as
not-enough-space
4. Don't signal if the pending_send_sz feature is not present. Older
versions of Hyper-V that don't implement this feature will poll.
Fixes: 03bad714a161 ("vmbus: more host signalling avoidance") Cc: Stable <stable@vger.kernel.org> # 4.14 and above Signed-off-by: Michael Kelley <mhkelley@outlook.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log