Rui Miguel Silva [Fri, 27 Aug 2021 13:11:54 +0000 (14:11 +0100)]
usb: isp1760: otg control register access
The set/clear of the otg control values is done writing to
two different 16bit registers, however we setup the regmap
width for isp1760/61 to 32bit value bits.
So, just access the clear register address (0x376)as the high
part of the otg control register set (0x374), and write the
values in one go to make sure they get clear/set.
Rui Miguel Silva [Fri, 27 Aug 2021 13:11:52 +0000 (14:11 +0100)]
usb: isp1760: write to status and address register
We were already writing directly the port status register to
trigger changes in isp1763. The same is needed in other IP
from the family, including also to setup the read address
before reading from device.
Rui Miguel Silva [Fri, 27 Aug 2021 13:11:51 +0000 (14:11 +0100)]
usb: isp1760: fix qtd fill length
When trying to send bulks bigger than the biggest block size
we need to split them over several qtd. Fix this limiting the
maximum qtd size to largest block size.
Rui Miguel Silva [Fri, 27 Aug 2021 13:11:50 +0000 (14:11 +0100)]
usb: isp1760: fix memory pool initialization
The loops to setup the memory pool were skipping some
blocks, that was not visible on the ISP1763 because it has
fewer blocks than the ISP1761. But won testing on that IP
from the family that would be an issue.
There are spelling mistakes in a comment and a literal string.
Fix them.
Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210826123959.14838-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yoshihiro Shimoda [Fri, 27 Aug 2021 06:32:27 +0000 (15:32 +0900)]
usb: host: xhci-rcar: Don't reload firmware after the completion
According to the datasheet, "Upon the completion of FW Download,
there is no need to write or reload FW.". Otherwise, it's possible
to cause unexpected behaviors. So, adds such a condition.
Fixes: 4ac8918f3a73 ("usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers") Cc: stable@vger.kernel.org # v3.17+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20210827063227.81990-1-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun [Fri, 27 Aug 2021 03:31:05 +0000 (11:31 +0800)]
usb: xhci-mtk: allow bandwidth table rollover
xhci-mtk has 64 slots for periodic bandwidth calculations and each
slot represents byte budgets on a microframe. When an endpoint's
allocation sits on the boundary of the table, byte budgets' slot
can be rolled over but the current implementation doesn't.
This patch allows the microframe index rollover and prevent
out-of-bounds array access.
Greg Kroah-Hartman [Fri, 27 Aug 2021 08:09:26 +0000 (10:09 +0200)]
Merge tag 'usb-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Only one patch for improving port index calculation for chipidea driver, no big changes.
* tag 'usb-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: host: fix port index underflow and UBSAN complains
Chunfeng Yun [Thu, 26 Aug 2021 08:36:37 +0000 (16:36 +0800)]
usb: mtu3: fix random remote wakeup
Some platforms, e.g. 8183/8192, use low level latch way to keep
wakeup signal, it may latch a wrong signal if debounce more time,
and enable wakeup earlier.
____________________
ip_sleep ____/ \__________
___________________
wakeup_signal ____________/ \______
_______________________________
wakeup_en _______/
^ ^
|(1) |(2)
latch wakeup_signal mistakenly at (1), should latch it at (2);
Workaround: delay about 100us to enable wakeup, meanwhile decrease
debounce time.
Chunfeng Yun [Thu, 26 Aug 2021 02:51:43 +0000 (10:51 +0800)]
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
xhci-mtk depends on xhci's internal virt_dev when it retrieves its
internal data from usb_host_endpoint both in add_endpoint and
drop_endpoint callbacks. But when setup packet was retired by
transaction errors in xhci_setup_device() path, a virt_dev for the slot
is newly created with real_port 0. This leads to xhci-mtks's NULL pointer
dereference from drop_endpoint callback as xhci-mtk assumes that virt_dev's
real_port is always started from one. The similar problems were addressed
by [1] but that can't cover the failure cases from setup_device.
This patch drops the usages of xhci's virt_dev in xhci-mtk's drop_endpoint
callback by adopting hashtable for searching mtk's schedule entity
from a given usb_host_endpoint pointer instead of searching a linked list.
So mtk's drop_endpoint callback doesn't have to rely on virt_dev at all.
[1] f351f4b63dac ("usb: xhci-mtk: fix oops when unbind driver")
Chunfeng Yun [Tue, 17 Aug 2021 08:36:29 +0000 (16:36 +0800)]
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
There are 4 USB controllers on MT8195, the controllers (IP1~IP3,
exclude IP0) have a wrong default SOF/ITP interval which is
calculated from the frame counter clock 24Mhz by default, but
in fact, the frame counter clock is 48Mhz, so we should set
the accurate interval according to 48Mhz for those controllers.
Note: the first controller no need set it.
Chunfeng Yun [Tue, 17 Aug 2021 08:36:25 +0000 (16:36 +0800)]
usb: xhci-mtk: fix issue of out-of-bounds array access
Bus bandwidth array access is based on esit, increase one
will cause out-of-bounds issue; for example, when esit is
XHCI_MTK_MAX_ESIT, will overstep boundary.
Fixes: 7c986fbc16ae ("usb: xhci-mtk: get the microframe boundary for ESIT") Cc: <stable@vger.kernel.org> Reported-by: Stan Lu <stan.lu@mediatek.com> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/1629189389-18779-5-git-send-email-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun [Tue, 17 Aug 2021 08:36:22 +0000 (16:36 +0800)]
dt-bindings: usb: mtk-xhci: add compatible for mt8195
There are 4 USB controllers on MT8195, the controllers (IP1~IP3,
exclude IP0) have a wrong default SOF/ITP interval which is
calculated from the frame counter clock 24Mhz by default, but
in fact, the frame counter clock is 48Mhz, so we should set
the accurate interval according to 48Mhz. Here add a new compatible
for MT8195, it's also supported in driver. But the first controller
(IP0) has no such issue, we prefer to use generic compatible,
e.g. mt8192's compatible.
Chunfeng Yun [Tue, 17 Aug 2021 08:36:21 +0000 (16:36 +0800)]
dt-bindings: usb: mtk-xhci: add optional property to disable usb2 ports
Add support to disable specific usb2 host ports, it's useful when
a usb2 port is disabled on some platforms, but enabled on others for
the same SoC, another case is that the different package may support
different number of ports.
Christophe JAILLET [Wed, 18 Aug 2021 19:32:49 +0000 (21:32 +0200)]
usb: bdc: Fix a resource leak in the error handling path of 'bdc_probe()'
If an error occurs after a successful 'clk_prepare_enable()' call, it must
be undone by a corresponding 'clk_disable_unprepare()' call.
This call is already present in the remove function.
Add this call in the error handling path and reorder the code so that the
'clk_prepare_enable()' call happens later in the function.
The goal is to have as much managed resources functions as possible
before the 'clk_prepare_enable()' call in order to keep the error handling
path simple.
While at it, remove the now unneeded 'clk' variable.
Chunfeng Yun [Fri, 20 Aug 2021 06:59:13 +0000 (14:59 +0800)]
Revert "usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint"
I find the patch introduce some issues, e.g.
1. oops happens when xhci_gen_setup() failed, and hash is not init
but try to destroy it;
2. memory leakage happens when fail to insert ep, need free sch_ep,
or insert ep after insert int list;
3. memory leakage happens when fail to allocate sch_array, need destroy
rhashtable;
4. it's better to check ep->hcpriv when drop ep;
so prefer to revert this patch, and resend it after the issues are fixed.
As discussed in following patch:
https://patchwork.kernel.org/patch/12420339
No need calculate number of uframes again, but should use value
form check_sch_tt(), if we plan to remove extra CS, also can do
it in check_sch_tt(). So revert this patch, and prepare to send
new patch for it.
Rui Miguel Silva [Thu, 19 Aug 2021 18:09:29 +0000 (19:09 +0100)]
usb: isp1760: clean never read udc_enabled warning
When CONFIG_USB_ISP1761_UDC is not enabled the udc_enabled variable is
never used since it is short circuited before in the logic operations.
This would trigger the following warning by clang analyzer:
drivers/usb/isp1760/isp1760-core.c:490:2: warning: Value stored to 'udc_enabled' is never read [clang-analyzer-deadcode.DeadStores]
udc_enabled = ((devflags & ISP1760_FLAG_ISP1763) ||
^
drivers/usb/isp1760/isp1760-core.c:490:2: note: Value stored to 'udc_enabled' is never read
Just swap the other of the operands in the logic operations.
Rui Miguel Silva [Thu, 19 Aug 2021 18:09:28 +0000 (19:09 +0100)]
usb: isp1760: do not shift in uninitialized slot
Even though it is not expected, and would trigger a WARN_ON, killing a
transfer in a uninitialized slot this sequence is warned by clang
analyzer, twice:
drivers/usb/isp1760/isp1760-hcd.c:1976:18: warning: The result of the left shift is undefined because the right operand is negative [clang-analyzer-core.UndefinedBinaryOperatorResult]
skip_map |= (1 << qh->slot);
drivers/usb/isp1760/isp1760-hcd.c:1983:18: warning: The result of the left shift is undefined because the right operand is negative [clang-analyzer-core.UndefinedBinaryOperatorResult]
skip_map |= (1 << qh->slot);
Rui Miguel Silva [Thu, 19 Aug 2021 18:09:26 +0000 (19:09 +0100)]
usb: isp1760: check maxpacketsize before using it
When checking if we need one more packet on a bulk pipe we may, even
though not probable at all, get there with a zero maxpacketsize.
In that case for sure no packet, no even a one more, will be
allocated.
This will clean the clang-analyzer warning:
drivers/usb/isp1760/isp1760-hcd.c:1856:38: warning: Division by zero [clang-analyzer-core.DivideZero]
&& !(urb->transfer_buffer_length %
Rui Miguel Silva [Thu, 19 Aug 2021 18:09:25 +0000 (19:09 +0100)]
usb: isp1760: ignore return value for bus change pattern
We do not care about the return value of that read between the
scratch register write and read, we really just want to make sure that
the pattern in the bus get changed to make sure we are testing
correctly the scratch pattern.
Clang-analyzer complains about the never read scratch variable:
>> drivers/usb/isp1760/isp1760-hcd.c:735:2: warning: Value stored to 'scratch' is never read [clang-analyzer-deadcode.DeadStores]
scratch = isp1760_hcd_read(hcd, HC_CHIP_ID_HIGH);
Just ignore the return value of that CHIP_ID_HIGH read, add more
information to the comment above why we are doing this. And as at it,
just do a small format change in the error message bellow.
Shuah Khan [Thu, 19 Aug 2021 22:59:37 +0000 (16:59 -0600)]
usbip:vhci_hcd USB port can get stuck in the disabled state
When a remote usb device is attached to the local Virtual USB
Host Controller Root Hub port, the bound device driver may send
a port reset command.
vhci_hcd accepts port resets only when the device doesn't have
port address assigned to it. When reset happens device is in
assigned/used state and vhci_hcd rejects it leaving the port in
a stuck state.
This problem was found when a blue-tooth or xbox wireless dongle
was passed through using usbip.
A few drivers reset the port during probe including mt76 driver
specific to this bug report. Fix the problem with a change to
honor reset requests when device is in used state (VDEV_ST_USED).
Anirudh Rayabharam [Fri, 20 Aug 2021 19:01:22 +0000 (00:31 +0530)]
usbip: clean up code in vhci_device_unlink_cleanup
The cleanup code for unlink_tx and unlink_rx lists is almost the same.
So, extract it into a new function and call it for both unlink_rx and
unlink_tx. Also, remove unnecessary log messages.
Anirudh Rayabharam [Fri, 20 Aug 2021 19:01:21 +0000 (00:31 +0530)]
usbip: give back URBs for unsent unlink requests during cleanup
In vhci_device_unlink_cleanup(), the URBs for unsent unlink requests are
not given back. This sometimes causes usb_kill_urb to wait indefinitely
for that urb to be given back. syzbot has reported a hung task issue [1]
for this.
To fix this, give back the urbs corresponding to unsent unlink requests
(unlink_tx list) similar to how urbs corresponding to unanswered unlink
requests (unlink_rx list) are given back.
Nadezda Lutovinova [Thu, 19 Aug 2021 16:33:23 +0000 (19:33 +0300)]
usb: musb: musb_dsps: request_irq() after initializing musb
If IRQ occurs between calling dsps_setup_optional_vbus_irq()
and dsps_create_musb_pdev(), then null pointer dereference occurs
since glue->musb wasn't initialized yet.
The patch puts initializing of neccesery data before registration
of the interrupt handler.
Found by Linux Driver Verification project (linuxtesting.org).
Nadezda Lutovinova [Thu, 19 Aug 2021 15:48:18 +0000 (18:48 +0300)]
usb: dwc3: imx8mp: request irq after initializing dwc3
If IRQ occurs between calling devm_request_threaded_irq() and
initializing dwc3_imx->dwc3, then null pointer dereference occurs
since dwc3_imx->dwc3 is used in dwc3_imx8mp_interrupt().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Evgeny Novikov [Wed, 25 Aug 2021 17:09:02 +0000 (20:09 +0300)]
usb: ehci-orion: Handle errors of clk_prepare_enable() in probe
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee07 ("ARM: Orion: EHCI: Add support for enabling clocks") Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Evgeny Novikov <novikov@ispras.ru> Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com> Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 20 Aug 2021 12:35:03 +0000 (15:35 +0300)]
xhci: Add bus number to some debug messages
As we register two usb buses for each xHC, and systems with several
hosts are more and more common it is getting hard to follow the
flow of debug messages without knowing which bus they belong to
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Mathias Nyman [Fri, 20 Aug 2021 12:35:00 +0000 (15:35 +0300)]
xhci: Fix failure to give back some cached cancelled URBs.
Only TDs with status TD_CLEARING_CACHE will be given back after
cache is cleared with a set TR deq command.
xhci_invalidate_cached_td() failed to set the TD_CLEARING_CACHE status
for some cancelled TDs as it assumed an endpoint only needs to clear the
TD it stopped on.
This isn't always true. For example with streams enabled an endpoint may
have several stream rings, each stopping on a different TDs.
Note that if an endpoint has several stream rings, the current code
will still only clear the cache of the stream pointed to by the last
cancelled TD in the cancel list.
This patch only focus on making sure all canceled TDs are given back,
avoiding hung task after device removal.
Another fix to solve clearing the caches of all stream rings with
cancelled TDs is needed, but not as urgent.
This issue was simultanously discovered and debugged by
by Tao Wang, with a slightly different fix proposal.
Fixes: 674f8438c121 ("xhci: split handling halted endpoints into two steps") Cc: <stable@vger.kernel.org> #5.12 Reported-by: Tao Wang <wat@codeaurora.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210820123503.2605901-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 20 Aug 2021 12:34:59 +0000 (15:34 +0300)]
xhci: fix even more unsafe memory usage in xhci tracing
Removes static char buffer usage in the following decode functions:
xhci_decode_ctrl_ctx()
xhci_decode_slot_context()
xhci_decode_usbsts()
xhci_decode_doorbell()
xhci_decode_ep_context()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor changes are needed in other xhci code as these functions are also
used elsewhere
Mathias Nyman [Fri, 20 Aug 2021 12:34:58 +0000 (15:34 +0300)]
xhci: fix unsafe memory usage in xhci tracing
Removes static char buffer usage in the following decode functions:
xhci_decode_trb()
xhci_decode_ptortsc()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h
f_hid provides the OUT Endpoint as only way for receiving reports
from the host. SETUP/SET_REPORT method is not supported, and this causes
a number of compatibility problems with various host drivers, especially
in the case of keyboard emulation using f_hid.
- Some hosts do not support the OUT Endpoint and ignore it,
so it becomes impossible for the gadget to receive a report
from the host. In the case of a keyboard, the gadget loses
the ability to receive the status of the LEDs.
- Some BIOSes/UEFIs can't work with HID devices with the OUT Endpoint
at all. This may be due to their bugs or incomplete implementation
of the HID standard.
For example, absolutely all Apple UEFIs can't handle the OUT Endpoint
if it goes after IN Endpoint in the descriptor and require the reverse
order (OUT, IN) which is a violation of the standard.
Other hosts either do not initialize gadgets with a descriptor
containing the OUT Endpoint completely (like some HP and DELL BIOSes
and embedded firmwares like on KVM switches), or initialize them,
but will not poll the IN Endpoint.
This patch adds configfs option no_out_endpoint=1 to disable
the OUT Endpoint and allows f_hid to receive reports from the host
via SETUP/SET_REPORT.
Previously, there was such a feature in f_hid, but it was replaced
by the OUT Endpoint [1] in the commit 99c515005857 ("usb: gadget: hidg:
register OUT INT endpoint for SET_REPORT"). So this patch actually
returns the removed functionality while making it optional.
For backward compatibility reasons, the OUT Endpoint mode remains
the default behaviour.
- The OUT Endpoint mode provides the report queue and reduces
USB overhead (eliminating SETUP routine) on transmitting a report
from the host.
- If the SETUP/SET_REPORT mode is used, there is no report queue,
so the userspace will only read last report. For classic HID devices
like keyboards this is not a problem, since it's intended to transmit
the status of the LEDs and only the last report is important.
This mode provides better compatibility with strange and buggy
host drivers.
Both modes passed USBCV tests. Checking with the USB protocol analyzer
also confirmed that everything is working as it should and the new mode
ensures operability in all of the described cases.
Greg Kroah-Hartman [Tue, 24 Aug 2021 13:31:33 +0000 (15:31 +0200)]
Merge tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.15 merge window
This includes following Thunderbolt/USB4 changes for the v5.15 merge
window:
* Include authorized value in the KOBJ_CHANGE event of a device router
* A couple of improvements to get the driver working also with the AMD
USB4 host controller.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix port linking by checking all adapters
thunderbolt: Do not read control adapter config space
thunderbolt: Handle ring interrupt by reading interrupt status register
thunderbolt: Add vendor specific NHI quirk for auto-clearing interrupt status
thunderbolt: Add authorized value to the KOBJ_CHANGE uevent
Linus Torvalds [Sun, 22 Aug 2021 16:49:31 +0000 (09:49 -0700)]
Merge tag 'powerpc-5.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix random crashes on some 32-bit CPUs by adding isync() after
locking/unlocking KUEP
- Fix intermittent crashes when loading modules with strict module RWX
- Fix a section mismatch introduce by a previous fix.
Thanks to Christophe Leroy, Fabiano Rosas, Laurent Vivier, Murilo
Opsfelder Araújo, Nathan Chancellor, and Stan Johnson.
h# -----BEGIN PGP SIGNATURE-----
* tag 'powerpc-5.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix set_memory_*() against concurrent accesses
powerpc/32s: Fix random crashes by adding isync() after locking/unlocking KUEP
powerpc/xive: Do not mark xive_request_ipi() as __init
Linus Torvalds [Sat, 21 Aug 2021 18:22:10 +0000 (11:22 -0700)]
Merge tag 'char-misc-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 5.14-rc7.
They consist of:
- revert for an interconnect patch that was found to have problems
- ipack tpci200 driver fixes for reported problems
- slimbus messaging and ngd fixes for reported problems
All are small and have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
ipack: tpci200: fix memory leak in the tpci200_register
ipack: tpci200: fix many double free issues in tpci200_pci_probe
slimbus: ngd: reset dma setup during runtime pm
slimbus: ngd: set correct device for pm
slimbus: messaging: check for valid transaction id
slimbus: messaging: start transaction ids from 1 instead of zero
Revert "interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate"
Linus Torvalds [Sat, 21 Aug 2021 18:10:06 +0000 (11:10 -0700)]
Merge tag 'usb-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fix from Greg KH:
"Here is a single USB typec tcpm fix for a reported problem for
5.14-rc7. It showed up in 5.13 and resolves an issue that Hans found.
It has been in linux-next this week with no reported problems"
* tag 'usb-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: Fix VDMs sometimes not being forwarded to alt-mode drivers
Linus Torvalds [Sat, 21 Aug 2021 18:04:26 +0000 (11:04 -0700)]
Merge tag 'riscv-for-linus-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- fix the sifive-l2-cache device tree bindings for json-schema
compatibility. This does not change the intended behavior of the
binding.
- avoid improperly freeing necessary resources during early boot.
* tag 'riscv-for-linus-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix a number of free'd resources in init_resources()
dt-bindings: sifive-l2-cache: Fix 'select' matching
Linus Torvalds [Sat, 21 Aug 2021 17:50:22 +0000 (10:50 -0700)]
Merge tag 'locks-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull mandatory file locking deprecation warning from Jeff Layton:
"As discussed on the list, this patch just adds a new warning for folks
who still have mandatory locking enabled and actually mount with '-o
mand'. I'd like to get this in for v5.14 so we can push this out into
stable kernels and hopefully reach folks who have mounts with -o mand.
For now, I'm operating under the assumption that we'll fully remove
this support in v5.15, but we can move that out if any legitimate
users of this facility speak up between now and then"
* tag 'locks-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
fs: warn about impending deprecation of mandatory locks
Linus Torvalds [Sat, 21 Aug 2021 15:11:22 +0000 (08:11 -0700)]
Merge tag 'block-5.14-2021-08-20' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three fixes from Ming Lei that should go into 5.14:
- Fix for a kernel panic when iterating over tags for some cases
where a flush request is present, a regression in this cycle.
- Request timeout fix
- Fix flush request checking"
* tag 'block-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
blk-mq: fix is_flush_rq
blk-mq: fix kernel panic during iterating over flush request
blk-mq: don't grab rq's refcount in blk_mq_check_expired()
Linus Torvalds [Sat, 21 Aug 2021 15:06:26 +0000 (08:06 -0700)]
Merge tag 'io_uring-5.14-2021-08-20' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few small fixes that should go into this release:
- Fix never re-assigning an initial error value for io_uring_enter()
for SQPOLL, if asked to do nothing
- Fix xa_alloc_cycle() return value checking, for cases where we have
wrapped around
- Fix for a ctx pin issue introduced in this cycle (Pavel)"
* tag 'io_uring-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
io_uring: fix xa_alloc_cycle() error return value check
io_uring: pin ctx on fallback execution
io_uring: only assign io_uring_enter() SQPOLL error in actual error case
Jeff Layton [Fri, 20 Aug 2021 13:29:50 +0000 (09:29 -0400)]
fs: warn about impending deprecation of mandatory locks
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org>
Li Jun [Fri, 18 Jun 2021 08:28:58 +0000 (16:28 +0800)]
usb: chipidea: host: fix port index underflow and UBSAN complains
If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains, here resolve this by not decrementing the index when
it is equal to 0, this copies the solution from commit 85e3990bea49
("USB: EHCI: avoid undefined pointer arithmetic and placate UBSAN")
Jens Axboe [Fri, 20 Aug 2021 20:53:59 +0000 (14:53 -0600)]
io_uring: fix xa_alloc_cycle() error return value check
We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.
Linus Torvalds [Fri, 20 Aug 2021 20:44:25 +0000 (13:44 -0700)]
Merge tag 'acpi-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two mistakes in new code.
Specifics:
- Prevent confusing messages from being printed if the PRMT table is
not present or there are no PRM modules (Aubrey Li).
- Fix the handling of suspend-to-idle entry and exit in the case when
the Microsoft UUID is used with the Low-Power S0 Idle _DSM
interface (Mario Limonciello)"
* tag 'acpi-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Invert Microsoft UUID entry and exit
ACPI: PRM: Deal with table not present or no module found
Linus Torvalds [Fri, 20 Aug 2021 20:38:42 +0000 (13:38 -0700)]
Merge tag 'pm-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix some issues in the ARM cpufreq drivers and in the operating
performance points (OPP) framework.
Specifics:
- Fix useless WARN() in the OPP core and prevent a noisy warning
from being printed by OPP _put functions (Dmitry Osipenko).
- Fix error path when allocation failed in the arm_scmi cpufreq
driver (Lukasz Luba).
- Blacklist Qualcomm sc8180x and Qualcomm sm8150 in
cpufreq-dt-platdev (Bjorn Andersson, Thara Gopinath).
- Forbid cpufreq for 1.2 GHz variant in the armada-37xx cpufreq
driver (Marek Behún)"
* tag 'pm-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
opp: Drop empty-table checks from _put functions
cpufreq: armada-37xx: forbid cpufreq for 1.2 GHz variant
cpufreq: blocklist Qualcomm sm8150 in cpufreq-dt-platdev
cpufreq: arm_scmi: Fix error path when allocation failed
opp: remove WARN when no valid OPPs remain
cpufreq: blacklist Qualcomm sc8180x in cpufreq-dt-platdev
Linus Torvalds [Fri, 20 Aug 2021 19:59:54 +0000 (12:59 -0700)]
Merge tag 'drm-fixes-2021-08-20-3' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regularly scheduled fixes. The ttm one solves a problem of GPU drivers
failing to load if debugfs is off in Kconfig, otherwise the i915 and
mediatek, and amdgpu fixes all fairly normal.
Nouveau has a couple of display fixes, but it has a fix for a
longstanding race condition in it's memory manager code, and the fix
mostly removes some code that wasn't working properly and has no
userspace users. This fix makes the diffstat kinda larger but in a
good (negative line-count) way.
* tag 'drm-fixes-2021-08-20-3' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Use DCN30 watermark calc for DCN301
drm/i915/dp: remove superfluous EXPORT_SYMBOL()
drm/i915/edp: fix eDP MSO pipe sanity checks for ADL-P
drm/i915: Tweaked Wa_14010685332 for all PCHs
drm/nouveau: rip out nvkm_client.super
drm/nouveau: block a bunch of classes from userspace
drm/nouveau/fifo/nv50-: rip out dma channels
drm/nouveau/kms/nv50: workaround EFI GOP window channel format differences
drm/nouveau/disp: power down unused DP links during init
drm/nouveau: recognise GA107
drm: Copy drm_wait_vblank to user before returning
drm/amd/display: Ensure DCN save after VM setup
drm/amdkfd: fix random KFDSVMRangeTest.SetGetAttributesTest test failure
drm/amd/pm: change the workload type for some cards
Revert "drm/amd/pm: fix workload mismatch on vega10"
drm: ttm: Don't bail from ttm_global_init if debugfs_create_dir fails
drm/mediatek: Add component_del in OVL and COLOR remove function
drm/mediatek: Add AAL output size configuration
- Add Jim Quinlan et al as Broadcom STB PCIe maintainers (Jim Quinlan)
- Increase D3hot-to-D0 delay for AMD Renoir/Cezanne XHCI (Marcin
Bachry)
- Correct iomem_get_mapping() usage for legacy_mem sysfs (Krzysztof
Wilczyński)
* tag 'pci-v5.14-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/sysfs: Use correct variable for the legacy_mem sysfs object
PCI: Increase D3 delay for AMD Renoir/Cezanne XHCI
MAINTAINERS: Add Jim Quinlan et al as Broadcom STB PCIe maintainers
MAINTAINERS: Add Rahul Tanwar as Intel LGM Gateway PCIe maintainer
Linus Torvalds [Fri, 20 Aug 2021 19:46:00 +0000 (12:46 -0700)]
Merge tag 'mmc-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- dw_mmc: Fix hang on data CRC error
- mmci: Fix voltage switch procedure for the stm32 variant
- sdhci-iproc: Fix some clock issues for BCM2711
- sdhci-msm: Fixup software timeout value
* tag 'mmc-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711
mmc: sdhci-iproc: Cap min clock frequency on BCM2711
mmc: sdhci-msm: Update the software timeout value for sdhc
mmc: mmci: stm32: Check when the voltage switch procedure should be done
mmc: dw_mmc: Fix hang on data CRC error
Linus Torvalds [Fri, 20 Aug 2021 19:31:10 +0000 (12:31 -0700)]
Merge tag 'sound-5.14-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound fixes from Takashi Iwai:
"This is a quick follow up for 5.14: a fix for a very recently
introduced regression on ASoC Intel Atom driver, and another trivial
HD-audio quirk for HP laptops"
* tag 'sound-5.14-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: intel: atom: Fix breakage for PCM buffer address setup
ALSA: hda/realtek: Limit mic boost on HP ProBook 445 G8
Linus Torvalds [Fri, 20 Aug 2021 19:18:49 +0000 (12:18 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix cleaning of vDSO directories
- Ensure CNTHCTL_EL2 is fully initialised when booting at EL2
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: initialize all of CNTHCTL_EL2
arm64: clean vdso & vdso32 files
Linus Torvalds [Fri, 20 Aug 2021 19:11:33 +0000 (12:11 -0700)]
Merge tag 'iommu-fixes-v5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix for a potential NULL-ptr dereference in IOMMU core code
- Two resource leak fixes
- Cache flush fix in the Intel VT-d driver
* tag 'iommu-fixes-v5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix incomplete cache flush in intel_pasid_tear_down_entry()
iommu/vt-d: Fix PASID reference leak
iommu: Check if group is NULL before remove device
iommu/dma: Fix leak in non-contiguous API
Mike Kravetz [Fri, 20 Aug 2021 02:04:33 +0000 (19:04 -0700)]
hugetlb: don't pass page cache pages to restore_reserve_on_error
syzbot hit kernel BUG at fs/hugetlbfs/inode.c:532 as described in [1].
This BUG triggers if the HPageRestoreReserve flag is set on a page in
the page cache. It should never be set, as the routine
huge_add_to_page_cache explicitly clears the flag after adding a page to
the cache.
The only code other than huge page allocation which sets the flag is
restore_reserve_on_error. It will potentially set the flag in rare out
of memory conditions. syzbot was injecting errors to cause memory
allocation errors which exercised this specific path.
The code in restore_reserve_on_error is doing the right thing. However,
there are instances where pages in the page cache were being passed to
restore_reserve_on_error. This is incorrect, as once a page goes into
the cache reservation information will not be modified for the page
until it is removed from the cache. Error paths do not remove pages
from the cache, so even in the case of error, the page will remain in
the cache and no reservation adjustment is needed.
Modify routines that potentially call restore_reserve_on_error with a
page cache page to no longer do so.
Note on fixes tag: Prior to commit 846be08578ed ("mm/hugetlb: expand
restore_reserve_on_error functionality") the routine would not process
page cache pages because the HPageRestoreReserve flag is not set on such
pages. Therefore, this issue could not be trigggered. The code added
by commit 846be08578ed ("mm/hugetlb: expand restore_reserve_on_error
functionality") is needed and correct. It exposed incorrect calls to
restore_reserve_on_error which is the root cause addressed by this
commit.
Marco Elver [Fri, 20 Aug 2021 02:04:30 +0000 (19:04 -0700)]
kfence: fix is_kfence_address() for addresses below KFENCE_POOL_SIZE
Originally the addr != NULL check was meant to take care of the case
where __kfence_pool == NULL (KFENCE is disabled). However, this does
not work for addresses where addr > 0 && addr < KFENCE_POOL_SIZE.
This can be the case on NULL-deref where addr > 0 && addr < PAGE_SIZE or
any other faulting access with addr < KFENCE_POOL_SIZE. While the
kernel would likely crash, the stack traces and report might be
confusing due to double faults upon KFENCE's attempt to unprotect such
an address.
Fix it by just checking that __kfence_pool != NULL instead.
Link: https://lkml.kernel.org/r/20210818130300.2482437-1-elver@google.com Fixes: 0ce20dd84089 ("mm: add Kernel Electric-Fence infrastructure") Signed-off-by: Marco Elver <elver@google.com> Reported-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com> Acked-by: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: <stable@vger.kernel.org> [5.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 20 Aug 2021 02:04:27 +0000 (19:04 -0700)]
mm: vmscan: fix missing psi annotation for node_reclaim()
In a debugging session the other day, Rik noticed that node_reclaim()
was missing memstall annotations. This means we'll miss pressure and
lost productivity resulting from reclaim on an overloaded local NUMA
node when vm.zone_reclaim_mode is enabled.
There haven't been any reports, but that's likely because
vm.zone_reclaim_mode hasn't been a commonly used feature recently, and
the intersection between such setups and psi users is probably nil.
But secondary memory such as CXL-connected DIMMS, persistent memory etc,
and the page demotion patches that handle them
(https://lore.kernel.org/lkml/20210401183216.443C4443@viggo.jf.intel.com/)
could soon make this a more common codepath again.
Link: https://lkml.kernel.org/r/20210818152457.35846-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Rik van Riel <riel@surriel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 20 Aug 2021 02:04:24 +0000 (19:04 -0700)]
mm/hwpoison: retry with shake_page() for unhandlable pages
HWPoisonHandlable() sometimes returns false for typical user pages due
to races with average memory events like transfers over LRU lists. This
causes failures in hwpoison handling.
There's retry code for such a case but does not work because the retry
loop reaches the retry limit too quickly before the page settles down to
handlable state. Let get_any_page() call shake_page() to fix it.
[naoya.horiguchi@nec.com: get_any_page(): return -EIO when retry limit reached] Link: https://lkml.kernel.org/r/20210819001958.2365157-1-naoya.horiguchi@linux.dev Link: https://lkml.kernel.org/r/20210817053703.2267588-1-naoya.horiguchi@linux.dev Fixes: 25182f05ffed ("mm,hwpoison: fix race with hugetlb page allocation") Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Reported-by: Tony Luck <tony.luck@intel.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [5.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 20 Aug 2021 02:04:21 +0000 (19:04 -0700)]
mm: memcontrol: fix occasional OOMs due to proportional memory.low reclaim
We've noticed occasional OOM killing when memory.low settings are in
effect for cgroups. This is unexpected and undesirable as memory.low is
supposed to express non-OOMing memory priorities between cgroups.
The reason for this is proportional memory.low reclaim. When cgroups
are below their memory.low threshold, reclaim passes them over in the
first round, and then retries if it couldn't find pages anywhere else.
But when cgroups are slightly above their memory.low setting, page scan
force is scaled down and diminished in proportion to the overage, to the
point where it can cause reclaim to fail as well - only in that case we
currently don't retry, and instead trigger OOM.
To fix this, hook proportional reclaim into the same retry logic we have
in place for when cgroups are skipped entirely. This way if reclaim
fails and some cgroups were scanned with diminished pressure, we'll try
another full-force cycle before giving up and OOMing.
[akpm@linux-foundation.org: coding-style fixes]
Link: https://lkml.kernel.org/r/20210817180506.220056-1-hannes@cmpxchg.org Fixes: 9783aa9917f8 ("mm, memcg: proportional memory.{low,min} reclaim") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Leon Yang <lnyng@fb.com> Reviewed-by: Rik van Riel <riel@surriel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Acked-by: Chris Down <chris@chrisdown.name> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [5.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doug Berger [Fri, 20 Aug 2021 02:04:12 +0000 (19:04 -0700)]
mm/page_alloc: don't corrupt pcppage_migratetype
When placing pages on a pcp list, migratetype values over
MIGRATE_PCPTYPES get added to the MIGRATE_MOVABLE pcp list.
However, the actual migratetype is preserved in the page and should
not be changed to MIGRATE_MOVABLE or the page may end up on the wrong
free_list.
The impact is that HIGHATOMIC or CMA pages getting bulk freed from the
PCP lists could potentially end up on the wrong buddy list. There are
various consequences but minimally NR_FREE_CMA_PAGES accounting could
get screwed up.
Yang Shi [Fri, 20 Aug 2021 02:04:09 +0000 (19:04 -0700)]
Revert "mm: swap: check if swap backing device is congested or not"
Due to the change about how block layer detects congestion the
justification of commit 8fd2e0b505d1 ("mm: swap: check if swap backing
device is congested or not") doesn't stand anymore, so the commit could
be just reverted in order to solve the race reported by commit 2efa33fc7f6e ("mm/shmem: fix shmem_swapin() race with swapoff"). The
fix was reverted by the previous patch.
Link: https://lkml.kernel.org/r/20210810202936.2672-3-shy828301@gmail.com Signed-off-by: Yang Shi <shy828301@gmail.com> Suggested-by: Hugh Dickins <hughd@google.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Minchan Kim <minchan@kernel.org> Cc: David Hildenbrand <david@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yang Shi [Fri, 20 Aug 2021 02:04:05 +0000 (19:04 -0700)]
Revert "mm/shmem: fix shmem_swapin() race with swapoff"
Due to the change about how block layer detects congestion the
justification of commit 8fd2e0b505d1 ("mm: swap: check if swap backing
device is congested or not") doesn't stand anymore, so the commit could
be just reverted in order to solve the race reported by commit 2efa33fc7f6e ("mm/shmem: fix shmem_swapin() race with swapoff"), so the
fix commit could be just reverted as well.
And that fix is also kind of buggy as discussed by [1] and [2].
Petr Pavlu [Sat, 7 Aug 2021 17:54:50 +0000 (19:54 +0200)]
riscv: Fix a number of free'd resources in init_resources()
Function init_resources() allocates a boot memory block to hold an array of
resources which it adds to iomem_resource. The array is filled in from its
end and the function then attempts to free any unused memory at the
beginning. The problem is that size of the unused memory is incorrectly
calculated and this can result in releasing memory which is in use by
active resources. Their data then gets corrupted later when the memory is
reused by a different part of the system.
Fix the size of the released memory to correctly match the number of unused
resource entries.
Fixes: ffe0e5261268 ("RISC-V: Improve init_resources()") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Reviewed-by: Sunil V L <sunilvl@ventanamicro.com> Acked-by: Nick Kossifidis <mick@ics.forth.gr> Tested-by: Sunil V L <sunilvl@ventanamicro.com> Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.
Fixes: 993dcfac64eb ("dt-bindings: riscv: sifive-l2-cache: convert bindings to json-schema") Signed-off-by: Rob Herring <robh@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Linus Torvalds [Thu, 19 Aug 2021 22:32:58 +0000 (15:32 -0700)]
Merge tag 'soc-fixes-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Not much to see here. Half the fixes this time are for Qualcomm dts
files, fixing small mistakes on certain machines. The other fixes are:
- A 5.13 regression fix for freescale QE interrupt controller\
- A fix for TI OMAP gpt12 timer error handling
- A randconfig build regression fix for ixp4xx
- Another defconfig fix following the CONFIG_FB dependency rework"
* tag 'soc-fixes-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: fsl: qe: fix static checker warning
ARM: ixp4xx: fix building both pci drivers
ARM: configs: Update the nhk8815_defconfig
bus: ti-sysc: Fix error handling for sysc_check_active_timer()
soc: fsl: qe: convert QE interrupt controller to platform_device
arm64: dts: qcom: sdm845-oneplus: fix reserved-mem
arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem
arm64: dts: qcom: sc7280: Fixup cpufreq domain info for cpu7
arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem mapping
arm64: dts: qcom: msm8992-bullhead: Remove PSCI
arm64: dts: qcom: c630: fix correct powerdown pin for WSA881x
* tag 'net-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (42 commits)
net: dpaa2-switch: disable the control interface on error path
Revert "flow_offload: action should not be NULL when it is referenced"
iavf: Fix ping is lost after untrusted VF had tried to change MAC
i40e: Fix ATR queue selection
r8152: fix the maximum number of PLA bp for RTL8153C
r8152: fix writing USB_BP2_EN
mptcp: full fully established support after ADD_ADDR
mptcp: fix memory leak on address flush
net/rds: dma_map_sg is entitled to merge entries
net: mscc: ocelot: allow forwarding from bridge ports to the tag_8021q CPU port
net: asix: fix uninit value bugs
ovs: clear skb->tstamp in forwarding path
net: mdio-mux: Handle -EPROBE_DEFER correctly
net: mdio-mux: Don't ignore memory allocation errors
net: mdio-mux: Delete unnecessary devm_kfree
net: dsa: sja1105: fix use-after-free after calling of_find_compatible_node, or worse
sch_cake: fix srchost/dsthost hashing mode
ixgbe, xsk: clean up the resources in ixgbe_xsk_pool_enable error path
net: qlcnic: add missed unlock in qlcnic_83xx_flash_read32
mac80211: fix locking in ieee80211_restart_work()
...
Linus Torvalds [Thu, 19 Aug 2021 19:19:58 +0000 (12:19 -0700)]
Merge tag 'platform-drivers-x86-v5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Enable SW_TABLET_MODE support for the TP200s
- Enable WMI on two more Gigabyte motherboards
* tag 'platform-drivers-x86-v5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: gigabyte-wmi: add support for B450M S2H V2
platform/x86: gigabyte-wmi: add support for X570 GAMING X
platform/x86: asus-nb-wmi: Add tablet_mode_sw=lid-flip quirk for the TP200s
platform/x86: asus-nb-wmi: Allow configuring SW_TABLET_MODE method with a module option
Vladimir Oltean [Thu, 19 Aug 2021 14:17:55 +0000 (17:17 +0300)]
net: dpaa2-switch: disable the control interface on error path
Currently dpaa2_switch_takedown has a funny name and does not do the
opposite of dpaa2_switch_init, which makes probing fail when we need to
handle an -EPROBE_DEFER.
A sketch of what dpaa2_switch_init does:
dpsw_open
dpaa2_switch_detect_features
dpsw_reset
for (i = 0; i < ethsw->sw_attr.num_ifs; i++) {
dpsw_if_disable
dpsw_if_set_stp
dpsw_vlan_remove_if_untagged
dpsw_if_set_tci
dpsw_vlan_remove_if
}
dpsw_vlan_remove
alloc_ordered_workqueue
dpsw_fdb_remove
dpaa2_switch_ctrl_if_setup
When dpaa2_switch_takedown is called from the error path of
dpaa2_switch_probe(), the control interface, enabled by
dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled,
because dpaa2_switch_takedown does not call
dpaa2_switch_ctrl_if_teardown.
Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this
means that a second probe of the driver will happen with the control
interface directly enabled.
Which if we investigate the /dev/dpaa2_mc_console log, we find out is
caused by:
[E, ctrl_if_set_pools:2211, DPMNG] ctrl_if must be disabled
So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in
reasonable limits, no reason to change STP state, re-add VLANs etc), and
rename it to something more conventional, like dpaa2_switch_teardown.
Fixes: 613c0a5810b7 ("staging: dpaa2-switch: enable the control interface") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cited commit added a check to make sure 'action' is not NULL, but
'action' is already dereferenced before the check, when calling
flow_offload_has_one_action().
Therefore, the check does not make any sense and results in a smatch
warning:
include/net/flow_offload.h:322 flow_action_mixed_hw_stats_check() warn:
variable dereferenced before check 'action' (see line 319)
Fix by reverting this commit.
Cc: gushengxian <gushengxian@yulong.com> Fixes: 9ea3e52c5bc8 ("flow_offload: action should not be NULL when it is referenced") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20210819105842.1315705-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sylwester Dziedziuch [Wed, 18 Aug 2021 17:42:17 +0000 (10:42 -0700)]
iavf: Fix ping is lost after untrusted VF had tried to change MAC
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e09b ("iavf: fix MAC address setting for VFs when filter is rejected") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan G <Gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arkadiusz Kubalewski [Wed, 18 Aug 2021 17:42:16 +0000 (10:42 -0700)]
i40e: Fix ATR queue selection
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886c1 ("i40e: Fix queue-to-TC mapping on Tx") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / users / hch / misc.git / log