The arguments desc_size and ZYNQMP_DMA_NUM_DESCS were 32 bit. Though
this overflow condition is not observed but it is a potential problem
in the case of 32-bit multiplication. Hence fix it by changing the
desc_size data type to size_t.
In addition to coverity fix it also reuse ZYNQMP_DMA_DESC_SIZE macro in
dma_alloc_coherent API argument.
When configuring a nommu classic m68k system enabling the uboot parameter
passing support (CONFIG_UBOOT) will produce the following compile error:
m68k-linux-ld: arch/m68k/kernel/uboot.o: in function `process_uboot_commandline':
uboot.c:(.init.text+0x32): undefined reference to `_init_sp'
The logic to support this option is only used on ColdFire based platforms
(in its head.S startup code). So make the selection of this option
depend on building for a ColdFire based platform.
The non-MMU m68k pagetable ZERO_PAGE() macro is being set to the
somewhat non-sensical value of "virt_to_page(0)". The zeroth page
is not in any way guaranteed to be a page full of "0". So the result
is that ZERO_PAGE() will almost certainly contain random values.
We already allocate a real "empty_zero_page" in the mm setup code shared
between MMU m68k and non-MMU m68k. It is just not hooked up to the
ZERO_PAGE() macro for the non-MMU m68k case.
Fix ZERO_PAGE() to use the allocated "empty_zero_page" pointer.
I am not aware of any specific issues caused by the old code.
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot triggers two WARNs in f2fs_is_valid_blkaddr and
__is_bitmap_valid. For example, in f2fs_is_valid_blkaddr,
if type is DATA_GENERIC_ENHANCE or DATA_GENERIC_ENHANCE_READ,
it invokes WARN_ON if blkaddr is not in the right range.
The call trace is as follows:
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
To prepare for support asynchronous tracer_init_tracefs initcall,
avoid calling create_trace_option_files before __update_tracer_options.
Otherwise, create_trace_option_files will show warning because
some tracers in trace_types list are already in tr->topts.
For example, hwlat_tracer call register_tracer in late_initcall,
and global_trace.dir is already created in tracing_init_dentry,
hwlat_tracer will be put into tr->topts.
Then if the __update_tracer_options is executed after hwlat_tracer
registered, create_trace_option_files find that hwlat_tracer is
already in tr->topts.
When setting bootparams="trace_event=initcall:initcall_start tp_printk=1" in the
cmdline, the output_printk() was called, and the spin_lock_irqsave() was called in the
atomic and irq disable interrupt context suitation. On the PREEMPT_RT kernel,
these locks are replaced with sleepable rt-spinlock, so the stack calltrace will
be triggered.
Fix it by raw_spin_lock_irqsave when PREEMPT_RT and "trace_event=initcall:initcall_start
tp_printk=1" enabled.
Even though idxd driver has always supported interrupt, it never actually
set the DMA_INTERRUPT cap bit. Rectify this mistake so the interrupt
capability is advertised.
The function percent_rmt_hitm_cmp() wrongly uses local HITMs for
sorting remote HITMs.
Since this function is to sort cache lines for remote HITMs, this patch
changes to use 'rmt_hitm' field for correct sorting.
Fixes: 9cb3500afc0980c5 ("perf c2c report: Add hitm/store percent related sort keys") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Joe Mario <jmario@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220530084253.750190-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Mounting NFS rootfs was timing out when deferred_probe_timeout was
non-zero [1]. This was because ip_auto_config() initcall times out
waiting for the network interfaces to show up when
deferred_probe_timeout was non-zero. While ip_auto_config() calls
wait_for_device_probe() to make sure any currently running deferred
probe work or asynchronous probe finishes, that wasn't sufficient to
account for devices being deferred until deferred_probe_timeout.
Commit 35a672363ab3 ("driver core: Ensure wait_for_device_probe() waits
until the deferred_probe_timeout fires") tried to fix that by making
sure wait_for_device_probe() waits for deferred_probe_timeout to expire
before returning.
However, if wait_for_device_probe() is called from the kernel_init()
context:
- Before deferred_probe_initcall() [2], it causes the boot process to
hang due to a deadlock.
- After deferred_probe_initcall() [3], it blocks kernel_init() from
continuing till deferred_probe_timeout expires and beats the point of
deferred_probe_timeout that's trying to wait for userspace to load
modules.
Neither of this is good. So revert the changes to
wait_for_device_probe().
If sd_probe() sees an early error before sdkp->device is initialized,
sd_zbc_release_disk() is called. This causes a NULL pointer dereference
when sd_is_zoned() is called inside that function. Avoid this by removing
the call to sd_zbc_release_disk() in sd_probe() error path.
This change is safe and does not result in zone information memory leakage
because the zone information for a zoned disk is allocated only when
sd_revalidate_disk() is called, at which point sdkp->disk_dev is fully set,
resulting in sd_disk_release() being called when needed to cleanup a disk
zone information using sd_zbc_release_disk().
Link: https://lore.kernel.org/r/20220601062544.905141-2-damien.lemoal@opensource.wdc.com Fixes: 89d947561077 ("sd: Implement support for ZBC devices") Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Suggested-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In AFS, a directory is handled as a file that the client downloads and
parses locally for the purposes of performing lookup and getdents
operations. The in-kernel afs filesystem has a number of functions that
do this.
A directory file is arranged as a series of 2K blocks divided into
32-byte slots, where a directory entry occupies one or more slots, plus
each block starts with one or more metadata blocks.
When parsing a block, if the last slots are occupied by a dirent that
occupies more than a single slot and the file position points at a slot
that's not the initial one, the logic in afs_dir_iterate_block() that
skips over it won't advance the file pointer to the end of it. This
will cause an infinite loop in getdents() as it will keep retrying that
block and failing to advance beyond the final entry.
Fix this by advancing the file pointer if the next entry will be beyond
it when we skip a block.
This was found by the generic/676 xfstest but can also be triggered with
something like:
1) A new passive FastOpen TCP socket is created.
This FO socket waits for an ACK coming from client to be a complete
ESTABLISHED one.
2) A socket operation on this socket goes through lock_sock()
release_sock() dance.
3) While the socket is owned by the user in step 2),
a retransmit of the SYN is received and stored in socket backlog.
4) At release_sock() time, the socket backlog is processed while
in process context.
5) A SYNACK packet is cooked in response of the SYN retransmit.
6) -> tcp_rtx_synack() is called in process context.
Before blamed commit, tcp_rtx_synack() was always called from BH handler,
from a timer handler.
Fix this by using TCP_INC_STATS() & NET_INC_STATS()
which do not assume caller is in non preemptible context.
In qdisc_run_end(), the spin_unlock() only has store-release semantic,
which guarantees all earlier memory access are visible before it. But
the subsequent test_bit() has no barrier semantics so may be reordered
ahead of the spin_unlock(). The store-load reordering may cause a packet
stuck problem.
The concurrent operations can be described as below,
CPU 0 | CPU 1
qdisc_run_end() | qdisc_run_begin()
. | .
----> /* may be reorderd here */ | .
| . | .
| spin_unlock() | set_bit()
| . | smp_mb__after_atomic()
---- test_bit() | spin_trylock()
. | .
Consider the following sequence of events:
CPU 0 reorder test_bit() ahead and see MISSED = 0
CPU 1 calls set_bit()
CPU 1 calls spin_trylock() and return fail
CPU 0 executes spin_unlock()
At the end of the sequence, CPU 0 calls spin_unlock() and does nothing
because it see MISSED = 0. The skb on CPU 1 has beed enqueued but no one
take it, until the next cpu pushing to the qdisc (if ever ...) will
notice and dequeue it.
This patch fix this by adding one explicit barrier. As spin_unlock() and
test_bit() ordering is a store-load ordering, a full memory barrier
smp_mb() is needed here.
Fixes: a90c57f2cedd ("net: sched: fix packet stuck problem for lockless qdisc") Signed-off-by: Guoju Fang <gjfang@linux.alibaba.com> Link: https://lore.kernel.org/r/20220528101628.120193-1-gjfang@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some features (LRO, HW GRO) conflict with XDP. If there is an attempt to
enable such features while XDP is active, they will be set to `off
[requested on]`. In order to activate these features after XDP is turned
off, the driver needs to call netdev_update_features(). This commit adds
this missing call after XDP state changes.
Fixes: cf6e34c8c22f ("net/mlx5e: Properly block LRO when XDP is enabled") Fixes: b0617e7b3500 ("net/mlx5e: Properly block HW GRO when XDP is enabled") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
tx_channel_offset is calculated in efx_allocate_msix_channels, but it is
also calculated again in efx_set_channels because it was originally done
there, and when efx_allocate_msix_channels was introduced it was
forgotten to be removed from efx_set_channels.
Moreover, the old calculation is wrong when using
efx_separate_tx_channels because now we can have XDP channels after the
TX channels, so n_channels - n_tx_channels doesn't point to the first TX
channel.
Remove the old calculation from efx_set_channels, and add the
initialization of this variable if MSI or legacy interrupts are used,
next to the initialization of the rest of the related variables, where
it was missing.
Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues") Reported-by: Tianhao Zhao <tizhao@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Normally, all channels have RX and TX queues, but this is not true if
modparam efx_separate_tx_channels=1 is used. In that cases, some
channels only have RX queues and others only TX queues (or more
preciselly, they have them allocated, but not initialized).
Fix efx_channel_has_tx_queues to return the correct value for this case
too.
Messages shown at probe time before the fix:
sfc 0000:03:00.0 ens6f0np0: MC command 0x82 inlen 544 failed rc=-22 (raw=0) arg=0
------------[ cut here ]------------
netdevice: ens6f0np0: failed to initialise TXQ -1
WARNING: CPU: 1 PID: 626 at drivers/net/ethernet/sfc/ef10.c:2393 efx_ef10_tx_init+0x201/0x300 [sfc]
[...] stripped
RIP: 0010:efx_ef10_tx_init+0x201/0x300 [sfc]
[...] stripped
Call Trace:
efx_init_tx_queue+0xaa/0xf0 [sfc]
efx_start_channels+0x49/0x120 [sfc]
efx_start_all+0x1f8/0x430 [sfc]
efx_net_open+0x5a/0xe0 [sfc]
__dev_open+0xd0/0x190
__dev_change_flags+0x1b3/0x220
dev_change_flags+0x21/0x60
[...] stripped
Messages shown at remove time before the fix:
sfc 0000:03:00.0 ens6f0np0: failed to flush 10 queues
sfc 0000:03:00.0 ens6f0np0: failed to flush queues
Fixes: 8700aff08984 ("sfc: fix channel allocation with brute force") Reported-by: Tianhao Zhao <tizhao@redhat.com> Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com> Tested-by: Íñigo Huguet <ihuguet@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
"struct smc_cdc_tx_pend **" can not directly convert
to "struct smc_wr_tx_pend_priv *".
Fixes: 2bced6aefa3d ("net/smc: put slot when connection is killed") Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
I think there is something wrong with BPF_PROBE_MEM in ___bpf_prog_run()
in big-endian machine. Let's make a test and see what will happen if we
want to load a 'u16' with BPF_PROBE_MEM.
Let's make the src value '0x0001', the value of dest register will become
0x0001000000000000, as the value will be loaded to the first 2 byte of
DST with following code:
The code of the test case is simply, it will load sk->sk_family to the
register with BPF_PROBE_MEM and check if it is AF_INET6. With this patch,
now the test case 'bpf_iter' can pass:
$10 bpf_iter:OK
Fixes: 2a02759ef5f8 ("bpf: Add support for BTF pointers to interpreter") Signed-off-by: Menglong Dong <imagedong@tencent.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jiang Biao <benbjiang@tencent.com> Reviewed-by: Hao Peng <flyingpeng@tencent.com> Cc: Ilya Leoshkevich <iii@linux.ibm.com> Link: https://lore.kernel.org/bpf/20220524021228.533216-1-imagedong@tencent.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There at least 6 PEBs reserved on UBI device:
1. EBA_RESERVED_PEBS[1]
2. WL_RESERVED_PEBS[1]
3. UBI_LAYOUT_VOLUME_EBS[2]
4. MIN_FASTMAP_RESERVED_PEBS[2]
When all ubi volumes take all their PEBs, there are 3 (EBA_RESERVED_PEBS +
WL_RESERVED_PEBS + MIN_FASTMAP_RESERVED_PEBS - MIN_FASTMAP_TAKEN_PEBS[1])
free PEBs. Since commit f9c34bb529975fe ("ubi: Fix producing anchor PEBs")
and commit 4b68bf9a69d22dd ("ubi: Select fastmap anchor PEBs considering
wear level rules") applied, there is only 1 (3 - FASTMAP_ANCHOR_PEBS[1] -
FASTMAP_NEXT_ANCHOR_PEBS[1]) free PEB to fill pool and wl_pool, after
filling pool, wl_pool is always empty. So, UBI could be stuck in an
infinite loop:
, which cause high cpu usage of ubi_bgt:
top - 12:10:42 up 5 min, 2 users, load average: 1.76, 0.68, 0.27
Tasks: 123 total, 3 running, 54 sleeping, 0 stopped, 0 zombie
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
1589 root 20 0 0 0 0 R 45.0 0.0 0:38.86 ubi_bgt0d
319 root 20 0 0 0 0 I 15.2 0.0 0:15.29 kworker/0:3-eve
371 root 20 0 0 0 0 I 14.9 0.0 0:12.85 kworker/3:3-eve
20 root 20 0 0 0 0 I 11.3 0.0 0:05.33 kworker/1:0-eve
202 root 20 0 0 0 0 I 11.3 0.0 0:04.93 kworker/2:3-eve
In commit 4b68bf9a69d22dd ("ubi: Select fastmap anchor PEBs considering
wear level rules"), there are three key changes:
1) Choose the fastmap anchor when the most free PEBs are available.
2) Enable anchor move within the anchor area again as it is useful
for distributing wear.
3) Import a candidate fm anchor and check this PEB's erase count during
wear leveling. If the wear leveling limit is exceeded, use the used
anchor area PEB with the lowest erase count to replace it.
The anchor candidate can be removed, we can check fm_anchor PEB's erase
count during wear leveling. Fix it by:
1) Removing 'fm_next_anchor' and check 'fm_anchor' during wear leveling.
2) Preferentially filling one free peb into fm_wl_pool in condition of
ubi->free_count > ubi->beb_rsvd_pebs, then try to reserve enough
free count for fastmap non anchor pebs after the above prerequisites
are met.
Then, there are at least 1 PEB in pool and 1 PEB in wl_pool after calling
ubi_refill_pools() with all erase works done.
With the `-z unique-symbol` linker flag or any similar mechanism,
it is possible to trigger the following:
ERROR: modpost: "param_set_uint.0" [vmlinux] is a static EXPORT_SYMBOL
The reason is that for now the condition from remove_dot():
if (m && (s[n + m] == '.' || s[n + m] == 0))
which was designed to test if it's a dot or a '\0' after the suffix
is never satisfied.
This is due to that `s[n + m]` always points to the last digit of a
numeric suffix, not on the symbol next to it (from a custom debug
print added to modpost):
param_set_uint.0, s[n + m] is '0', s[n + m + 1] is '\0'
So it's off-by-one and was like that since 2014.
Fix this for the sake of any potential upcoming features, but don't
bother stable-backporting, as it's well hidden -- apart from that
LD flag, it can be triggered only with GCC LTO which never landed
upstream.
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
am65_cpsw_init_cpts() and am65_cpsw_nuss_probe() don't release
the refcount in error case.
Add missing of_node_put() to avoid refcount leak.
Fixes: b1f66a5bee07 ("net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support") Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "fsp->location" variable comes from user via ethtool_get_rxnfc().
Check that it is valid to prevent an out of bounds read.
Fixes: 7aab747e5563 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In qdisc_run_begin(), smp_mb__before_atomic() used before test_bit()
does not provide any ordering guarantee as test_bit() is not an atomic
operation. This, added to the fact that the spin_trylock() call at
the beginning of qdisc_run_begin() does not guarantee acquire
semantics if it does not grab the lock, makes it possible for the
following statement :
if (test_bit(__QDISC_STATE_MISSED, &qdisc->state))
to be executed before an enqueue operation called before
qdisc_run_begin().
In the above scenario, CPU 1 and CPU 2 both try to grab the
qdisc->seqlock at the same time. Only CPU 2 succeeds and enters the
bypass code path, where it emits its skb then calls __qdisc_run().
CPU1 fails, sets MISSED and goes down the traditionnal enqueue() +
dequeue() code path. But when executing qdisc_run_begin() for the
second time, after enqueuing its skbuff, it sees the MISSED bit still
set (by itself) and consequently chooses to exit early without setting
it again nor trying to grab the spinlock again.
Meanwhile CPU2 has seen MISSED = 1, cleared it, checked the queue
and found it empty, so it returned.
At the end of the sequence, we end up with skb1 enqueued in the
backlog, both CPUs out of __dev_xmit_skb(), the MISSED bit not set,
and no __netif_schedule() called made. skb1 will now linger in the
qdisc until somebody later performs a full __qdisc_run(). Associated
to the bypass capacity of the qdisc, and the ability of the TCP layer
to avoid resending packets which it knows are still in the qdisc, this
can lead to serious traffic "holes" in a TCP connection.
We fix this by replacing the smp_mb__before_atomic() / test_bit() /
set_bit() / smp_mb__after_atomic() sequence inside qdisc_run_begin()
by a single test_and_set_bit() call, which is more concise and
enforces the needed memory barriers.
Fixes: 89837eb4b246 ("net: sched: add barrier to ensure correct ordering for lockless qdisc") Signed-off-by: Vincent Ray <vray@kalrayinc.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220526001746.2437669-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The argument of scatterwalk_unmap() is supposed to be the void* that was
returned by the previous scatterwalk_map() call.
The s390 AES-GCM implementation was instead passing the pointer to the
struct scatter_walk.
This doesn't actually break anything because scatterwalk_unmap() only uses
its argument under CONFIG_HIGHMEM and ARCH_HAS_FLUSH_ON_KUNMAP.
There are multiple xDR and xFR registers, the index is
from 0 to 7. FSL_SAI_xDR and FSL_SAI_xFR is abandoned,
replace them with FSL_SAI_xDR0 and FSL_SAI_xFR0.
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in some error paths.
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
In __device_attach function, The lock holding logic is as follows:
...
__device_attach
device_lock(dev) // get lock dev
async_schedule_dev(__device_attach_async_helper, dev); // func
async_schedule_node
async_schedule_node_domain(func)
entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC);
/* when fail or work limit, sync to execute func, but
__device_attach_async_helper will get lock dev as
well, which will lead to A-A deadlock. */
if (!entry || atomic_read(&entry_count) > MAX_WORK) {
func;
else
queue_work_node(node, system_unbound_wq, &entry->work)
device_unlock(dev)
As shown above, when it is allowed to do async probes, because of
out of memory or work limit, async work is not allowed, to do
sync execute instead. it will lead to A-A deadlock because of
__device_attach_async_helper getting lock dev.
To fix the deadlock, move the async_schedule_dev outside device_lock,
as we can see, in async_schedule_node_domain, the parameter of
queue_work_node is system_unbound_wq, so it can accept concurrent
operations. which will also not change the code logic, and will
not lead to deadlock.
We can get "failed to disable" clock_unprepare warnings on unbind at least
for the serial console device if the unbind is done before the device has
been idled.
As some devices are using deferred idle, we must check the status for
pending idle work to idle the device.
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d043947b (serial: stm32: fix word length configuration) Cc: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only CS7 and CS8 seem supported but CSIZE is not sanitized from CS5 or
CS6 to CS8. In addition, ASC_CTL_MODE_7BIT_PAR suggests that CS7 has
to have parity, thus add PARENB.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS8 is supported but CSIZE was not sanitized to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Similarly, INPCK, PARMRK, and BRKINT are reported textually unsupported
but were not cleared in termios c_iflag which is the machine-readable
format.
Fixes: 45c054d0815b (tty: serial: add driver for the SiFive UART) Cc: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220519081808.3776-7-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 are supported but CSIZE is not sanitized with
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 are supported but CSIZE is not sanitized after
fallthrough from CS5 or CS6 to CS7.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 seem supported but CSIZE is not sanitized to CS8 in
the default: block.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND relate to behavior
within RS485 operation. The driver checks if they have the same value
which is not possible to realize with the hardware. The check is taken
regardless of SER_RS485_ENABLED flag and -EINVAL is returned when the
check fails, which creates problems.
This check makes it unnecessarily complicated to turn RS485 mode off as
simple zeroed serial_rs485 struct will trigger that equal values check.
In addition, the driver itself memsets its rs485 structure to zero when
RS485 is disabled but if userspace would try to make an TIOCSRS485
ioctl() call with the very same struct, it would end up failing with
-EINVAL which doesn't make much sense.
Resolve the problem by moving the check inside SER_RS485_ENABLED block.
The uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
Since the startup() callback is reading/writing registers used by
the console write() callback (AML_UART_CONTROL), its access must
be synchronized using the port->lock. Currently it is not.
The startup() callback is the only function that explicitly enables
interrupts. Without the synchronization, it is possible that
interrupts become accidentally permanently disabled.
Some implementations of the SBI time extension depend on hart-local
state (for example, CSRs) that are lost or hardware that is powered
down when a CPU is suspended. To be safe, the clockevents driver
cannot assume that timer IRQs will be received during CPU suspend.
Fixes: 62b019436814 ("clocksource: new RISC-V SBI timer driver") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Anup Patel <anup@brainfault.org> Link: https://lore.kernel.org/r/20220509012121.40031-1-samuel@sholland.org Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node_and_match returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Add device managed action to sync pending queue work, otherwise
the queued work may run after the work is destroyed.
Fixes: 4ed754de2d66 ("extcon: Add support for ptn5150 extcon driver") Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The panic notifier infrastructure executes registered callbacks when
a panic event happens - such callbacks are executed in atomic context,
with interrupts and preemption disabled in the running CPU and all other
CPUs disabled. That said, mutexes in such context are not a good idea.
This patch replaces a regular mutex with a mutex_trylock safer approach;
given the nature of the mutex used in the driver, it should be pretty
uncommon being unable to acquire such mutex in the panic path, hence
no functional change should be observed (and if it is, that would be
likely a deadlock with the regular mutex).
Fixes: 2227b7c74634 ("coresight: add support for CPU debug module") Cc: Leo Yan <leo.yan@linaro.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20220427224924.592546-10-gpiccoli@igalia.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
Small adjustment the scale calibration value for the sc2731,
use new name sc2731_[big|small]_scale_graph_calib, and remove
the origin [big|small]_scale_graph_calib struct for unused.
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
wait_for_completion_timeout() returns unsigned long not long.
it returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case
Fixes: e813dde6f833 ("iio: stmpe-adc: Use wait_for_completion_timeout") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com> Link: https://lore.kernel.org/r/20220412065150.14486-1-linmq006@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The list iterator 'pmem' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, just gen_pool_free/set NULL/list_del() and return
when found, otherwise list_del HEAD and return;
The list iterator value 'buf' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty (in this case, the
check 'if (!buf) {' will always be false and never exit expectly).
To fix the bug, use a new variable 'iter' as the list iterator,
while use the original variable 'buf' as a dedicated pointer to
point to the found element.
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
If device_register() fails, device_unregister() should not be called
because it will free some resources that are not allocated.
put_device() should be used instead.
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence") Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.
This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?
There are two possibilities, that both have (dis)advantages:
1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
Advantage: The reader can interpret this as "the line is over".
Disadvantage: read() returning 0 means EOF, the reader could also
interpret it as "there's no more data" and stop reading or even
close the PT.
2. The next read() returns the next line, the EOF is silently discarded.
Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
do this since commit 40d5e0905a03 ("n_tty: Fix EOF push handling");
this behavior was recently broken by commit 359303076163 ("tty:
n_tty: do not look ahead for EOL character past the end of the buffer").
Advantage: read() won't return 0 (EOF), reader less likely to be
confused (and things like `while(read(..)>0)` don't break)
Disadvantage: The reader can't really know if the read() continues
the last line (that filled the whole read buffer) or starts a
new line.
As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.
This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.
Based on a patch from Linus Torvalds.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611 Fixes: 359303076163 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer") Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Daniel Gibson <daniel@gibson.sh> Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.sh Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
As the possible failure of the kmalloc(), the not_checked and checked
could be NULL pointer.
Therefore, it should be better to check it in order to avoid the
dereference of the NULL pointer.
Also, we need to kfree the 'not_checked' and 'checked' to avoid
the memory leak if fails.
And since it is just a test, it may directly return without error
number.
If the list does not exit early then data == NULL and 'module' does not
point to a valid list element.
Using 'module' in such a case is not valid and was therefore removed.
Fixes: 6dd67645f22c ("greybus: audio: Use single codec driver registration") Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Vaibhav Agarwal <vaibhav.sr@gmail.com> Reviewed-by: Mark Greer <mgreer@animalcreek.com> Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com> Link: https://lore.kernel.org/r/20220321123626.3068639-1-jakobkoschel@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the MIPS_ALCHEMY board selection is MIPS_XXS1500 instead of
MIPS_DB1XXX, the PCMCIA driver 'db1xxx_ss' has build errors due
to missing DB1XXX symbols. The PCMCIA driver should be restricted
to MIPS_DB1XXX instead of MIPS_ALCHEMY to fix this build error.
Make the test_dummy_encryption mount option require that the encrypt
feature flag be already enabled on the filesystem, rather than
automatically enabling it. Practically, this means that "-O encrypt"
will need to be included in MKFS_OPTIONS when running xfstests with the
test_dummy_encryption mount option. (ext4/053 also needs an update.)
Moreover, as long as the preconditions for test_dummy_encryption are
being tightened anyway, take the opportunity to start rejecting it when
!CONFIG_FS_ENCRYPTION rather than ignoring it.
The motivation for requiring the encrypt feature flag is that:
- Having the filesystem auto-enable feature flags is problematic, as it
bypasses the usual sanity checks. The specific issue which came up
recently is that in kernel versions where ext4 supports casefold but
not encrypt+casefold (v5.1 through v5.10), the kernel will happily add
the encrypt flag to a filesystem that has the casefold flag, making it
unmountable -- but only for subsequent mounts, not the initial one.
This confused the casefold support detection in xfstests, causing
generic/556 to fail rather than be skipped.
- The xfstests-bld test runners (kvm-xfstests et al.) already use the
required mkfs flag, so they will not be affected by this change. Only
users of test_dummy_encryption alone will be affected. But, this
option has always been for testing only, so it should be fine to
require that the few users of this option update their test scripts.
- f2fs already requires it (for its equivalent feature flag).
Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.com> Link: https://lore.kernel.org/r/20220519204437.61645-1-ebiggers@kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Reported-by: Stephen Zhang <starzhangzsd@gmail.com> Fixes: 7505576d1c1a ("MIPS: add support for SGI Octane (IP30)") Cc: stable@vger.kernel.org # v5.5+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Reported-by: Stephen Zhang <starzhangzsd@gmail.com> Fixes: 0ebb2f4159af ("MIPS: IP27: Update/restructure CPU overrides") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current rxe_requester() doesn't generate a completion when processing an
unsupported/invalid opcode. If rxe driver doesn't support a new opcode
(e.g. RDMA Atomic Write) and RDMA library supports it, an application
using the new opcode can reproduce this issue. Fix the issue by calling
"goto err;".
Commit d92c370a16cb ("block: really clone the block cgroup in
bio_clone_blkg_association") changed bio_clone_blkg_association() to
just clone bio->bi_blkg reference from source to destination bio. This
is however wrong if the source and destination bios are against
different block devices because struct blkcg_gq is different for each
bdev-blkcg pair. This will result in IOs being accounted (and throttled
as a result) multiple times against the same device (src bdev) while
throttling of the other device (dst bdev) is ignored. In case of BFQ the
inconsistency can even result in crashes in bfq_bic_update_cgroup().
Fix the problem by looking up correct blkcg_gq for the cloned bio.
Reported-by: Logan Gunthorpe <logang@deltatee.com> Reported-and-tested-by: Donald Buczek <buczek@molgen.mpg.de> Fixes: d92c370a16cb ("block: really clone the block cgroup in bio_clone_blkg_association") CC: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220602081242.7731-1-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bios queued into BFQ IO scheduler can be associated with a cgroup that
was already offlined. This may then cause insertion of this bfq_group
into a service tree. But this bfq_group will get freed as soon as last
bio associated with it is completed leading to use after free issues for
service tree users. Fix the problem by making sure we always operate on
online bfq_group. If the bfq_group associated with the bio is not
online, we pick the first online parent.
CC: stable@vger.kernel.org Fixes: e21b7a0b9887 ("block, bfq: add full hierarchical scheduling and cgroups support") Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-9-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BFQ usage of __bio_blkcg() is a relict from the past. Furthermore if bio
would not be associated with any blkcg, the usage of __bio_blkcg() in
BFQ is prone to races with the task being migrated between cgroups as
__bio_blkcg() calls at different places could return different blkcgs.
Convert BFQ to the new situation where bio->bi_blkg is initialized in
bio_set_dev() and thus practically always valid. This allows us to save
blkcg_gq lookup and noticeably simplify the code.
CC: stable@vger.kernel.org Fixes: 0fe061b9f03c ("blkcg: fix ref count issue with bio_blkcg() using task_css") Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-8-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We call bfq_init_rq() from request merging functions where requests we
get should have already gone through bfq_init_rq() during insert and
anyway we want to do anything only if the request is already tracked by
BFQ. So replace calls to bfq_init_rq() with RQ_BFQQ() instead to simply
skip requests untracked by BFQ. We move bfq_init_rq() call in
bfq_insert_request() a bit earlier to cover request merging and thus
can transfer FIFO position in case of a merge.
CC: stable@vger.kernel.org Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-6-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bfq_insert_request() we unlock bfqd->lock only to call
trace_block_rq_insert() and then lock bfqd->lock again. This is really
pointless since tracing is disabled if we really care about performance
and even if the tracepoint is enabled, it is a quick call.
CC: stable@vger.kernel.org Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-5-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can happen that the parent of a bfqq changes between the moment we
decide two queues are worth to merge (and set bic->stable_merge_bfqq)
and the moment bfq_setup_merge() is called. This can happen e.g. because
the process submitted IO for a different cgroup and thus bfqq got
reparented. It can even happen that the bfqq we are merging with has
parent cgroup that is already offline and going to be destroyed in which
case the merge can lead to use-after-free issues such as:
BUG: KASAN: use-after-free in __bfq_deactivate_entity+0x9cb/0xa50
Read of size 8 at addr ffff88800693c0c0 by task runc:[2:INIT]/10544
smatch warnings:
drivers/thermal/thermal_core.c:1020 __thermal_cooling_device_register() warn: possible memory leak of 'cdev'
by freeing the cdev when exiting the function in the error path.
Fixes: 584837618100 ("thermal/drivers/core: Use a char pointer for the cooling device name") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210319202257.890848-1-daniel.lezcano@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log