There are sleep in atomic context bugs when uploading device dump
data in mwifiex. The root cause is that dev_coredumpv could not
be used in atomic contexts, because it calls dev_set_name which
include operations that may sleep. The call tree shows execution
paths that could lead to bugs:
This patch uses delayed work to replace timer and moves the operations
that may sleep into a delayed work in order to mitigate bugs, it was
tested on Marvell 88W8801 chip whose port is usb and the firmware is
usb8801_uapsta.bin. The following is the result after using delayed
work to replace timer.
[ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.
This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.
Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.
Don't set Accessed/Dirty bits for a struct page with PG_reserved set,
i.e. don't set A/D bits for the ZERO_PAGE. The ZERO_PAGE (or pages
depending on the architecture) should obviously never be written, and
similarly there's no point in marking it accessed as the page will never
be swapped out or reclaimed. The comment in page-flags.h is quite clear
that PG_reserved pages should be managed only by their owner, and
strictly following that mandate also simplifies KVM's logic.
Fixes: 7df003c85218 ("KVM: fix overflow of zero page refcount with ksm running") Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220429010416.2788472-4-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Original assert/deassert bit is BIT(0), but it's more resonable to modify
them to BIT(id % 32) which is based on id.
This patch will not influence any previous driver because the reset is
only used for thermal. The id (MT8183_INFRACFG_AO_THERM_SW_RST) is 0.
Fixes: 64ebb57a3df6 ("clk: reset: Modify reset-controller driver") Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220523093346.28493-3-rex-bc.chen@mediatek.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The last resume result exposing logic in cros_ec_sleep_event()
incorrectly requires S0ix support, which doesn't work on ARM based
systems where S0ix doesn't exist. That's because cros_ec_sleep_event()
only reports the last resume result when the EC indicates the last sleep
event was an S0ix resume. On ARM systems, the last sleep event is always
S3 resume, but the EC can still detect sleep hang events in case some
other part of the AP is blocking sleep.
Always expose the last resume result if the EC supports it so that this
works on all devices regardless of S0ix support. This fixes sleep hang
detection on ARM based chromebooks like Trogdor.
Cc: Rajat Jain <rajatja@chromium.org> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Hsin-Yi Wang <hsinyi@chromium.org> Cc: Tzung-Bi Shih <tzungbi@kernel.org> Reviewed-by: Guenter Roeck <groeck@chromium.org> Reviewed-by: Evan Green <evgreen@chromium.org> Fixes: 7235560ac77a ("platform/chrome: Add support for v1 of host sleep event") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org> Link: https://lore.kernel.org/r/20220614075726.2729987-1-swboyd@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit e2be04c7f995 ("License cleanup: add SPDX license identifier to
uapi header files with a license") added the correct SPDX identifier to
include/uapi/linux/netfilter/xt_IDLETIMER.h.
A subsequent commit removed it for no reason and reintroduced the UAPI
license incorrectness as the file is now missing the UAPI exception
again.
Add it back and remove the GPLv2 boilerplate while at it.
In the function tegra_xusb_powerdomain_init(),
dev_pm_domain_attach_by_name() may return NULL in some cases,
so IS_ERR() doesn't meet the requirements. Thus fix it.
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 73108aa90cbf ("USB: ohci-nxp: Use isp1301 driver") Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220603141231.979-1-linmq006@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 796bcae7361c ("USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]") Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220602110849.58549-1-linmq006@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 237960880960 ("mtd: partitions: redboot: seek fis-index-block in the right node") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220526110652.64849-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a deadlock between sm_release and sm_cache_flush_work
which is a work item. The cancel_work_sync in sm_release will
not return until sm_cache_flush_work is finished. If we hold
mutex_lock and use cancel_work_sync to wait the work item to
finish, the work item also requires mutex_lock. As a result,
the sm_release will be blocked forever. The race condition is
shown below:
Smatch warnings:
drivers/hid/hid-cp2112.c:793 cp2112_xfer() error: __memcpy()
'data->block[1]' too small (33 vs 255)
drivers/hid/hid-cp2112.c:793 cp2112_xfer() error: __memcpy() 'buf' too
small (64 vs 255)
The 'read_length' variable is provided by 'data->block[0]' which comes
from user and it(read_length) can take a value between 0-255. Add an
upper bound to 'read_length' variable to prevent a buffer overflow in
memcpy().
pm_runtime_enable() will increase power disable depth. If
dw_pcie_ep_init() fails, we should use pm_runtime_disable() to balance it
with pm_runtime_enable().
Add missing pm_runtime_disable() for tegra_pcie_config_ep().
Fixes: c57247f940e8 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194") Link: https://lore.kernel.org/r/20220602031910.55859-1-linmq006@gmail.com Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc192 ("mtd: physmap_of: add a hook for Versatile write protection") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220523143255.4376-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc192 ("mtd: physmap_of: add a hook for Versatile write protection") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220523140205.48625-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two UART clock groups, each having a mux to select its
upstream clock source. The register/bit definitions for accessing these
two muxes appear to have been reversed since introduction. Correct them
so as to match the hardware manual.
In case push_rcu() and related functions are buggy, there's a
WARN_ON(len >= 128), which the selftest tries to hit by being tricky. In
case it is hit, we shouldn't corrupt the kernel's stack, though;
otherwise it may be hard to even receive the report that it's buggy. So
conditionalize the stack write based on that WARN_ON()'s return value.
Note that this never *actually* happens anyway. The WARN_ON() in the
first place is bounded by IS_ENABLED(DEBUG), and isn't expected to ever
actually hit. This is just a debugging sanity check.
Additionally, hoist the constant 128 into a named enum,
MAX_ALLOWEDIPS_BITS, so that it's clear why this value is chosen.
Using msleep() is problematic because it's compared against
ratelimiter.c's ktime_get_coarse_boottime_ns(), which means on systems
with slow jiffies (such as UML's forced HZ=100), the result is
inaccurate. So switch to using schedule_hrtimeout().
However, hrtimer gives us access only to the traditional posix timers,
and none of the _COARSE variants. So now, rather than being too
imprecise like jiffies, it's too precise.
One solution would be to give it a large "range" value, but this will
still fire early on a loaded system. A better solution is to align the
timeout to the actual coarse timer, and then round up to the nearest
tick, plus change.
So add the timeout to the current coarse time, and then
schedule_hrtimer() until the absolute computed time.
This should hopefully reduce flakes in CI as well. Note that we keep the
retry loop in case the entire function is running behind, because the
test could still be scheduled out, by either the kernel or by the
hypervisor's kernel, in which case restarting the test and hoping to not
be scheduled out still helps.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the case of sk->dccps_qpolicy == DCCPQ_POLICY_PRIO, dccp_qpolicy_full
will drop a skb when qpolicy is full. And the lock in dccp_sendmsg is
released before sock_alloc_send_skb and then relocked after
sock_alloc_send_skb. The following conditions may lead dccp_qpolicy_push
to add skb to an already full sk_write_queue:
thread1--->lock
thread1--->dccp_qpolicy_full: queue is full. drop a skb
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_full: queue is not full. no need to drop.
thread2--->unlock
thread1--->lock
thread1--->dccp_qpolicy_push: add a skb. queue is full.
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_push: add a skb!
thread2--->unlock
Fix this by moving dccp_qpolicy_full.
Fixes: b1308dc015eb ("[DCCP]: Set TX Queue Length Bounds via Sysctl") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Link: https://lore.kernel.org/r/20220729110027.40569-1-hbh25y@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The prototype of input features of ionic_set_nic_features() is
netdev_features_t, but the vlan_flags is using the private
definition of ionic drivers. It should use the variable
ctx.cmd.lif_setattr.features, rather than features to check
the vlan flags. So fixes it.
Fixes: beead698b173 ("ionic: Add the basic NDO callbacks for netdev support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Acked-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bernard reported that trying to unload rose module would lead
to infamous messages:
unregistered_netdevice: waiting for rose0 to become free. Usage count = xx
This patch solves the issue, by making sure each socket referring to
a netdevice holds a reference count on it, and properly releases it
in rose_release().
rose_dev_first() is also fixed to take a device reference
before leaving the rcu_read_locked section.
Following patch will add ref_tracker annotations to ease
future bug hunting.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Bernard Pidoux <f6bvp@free.fr> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Bernard Pidoux <f6bvp@free.fr> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to suppress warnings from sily map sizes. Also switch
from GFP_USER to GFP_KERNEL_ACCOUNT, I'm pretty sure I misunderstood
the flags when writing this code.
Fix max_rate option in TC, check for proper quanta boundaries.
Check for minimum value provided and if it fits expected 50Mbps
quanta.
Without this patch, iavf could send settings for max_rate limiting
that would be accepted from by PF even the max_rate option is less
than expected 50Mbps quanta. It results in no rate limiting
on traffic as rate limiting will be floored to 0.
The commit 3c82a21f4320 ("net: allow binding socket in a VRF when
there's an unbound socket") changed the inet socket lookup to avoid
packets in a VRF from matching an unbound socket. This is to ensure the
necessary isolation between the default and other VRFs for routing and
forwarding. VRF-unaware processes running in the default VRF cannot
access another VRF and have to be run with 'ip vrf exec <vrf>'. This is
to be expected with tcp_l3mdev_accept disabled, but could be reallowed
when this sysctl option is enabled. So instead of directly checking dif
and sdif in inet[6]_match, here call inet_sk_bound_dev_eq(). This
allows a match on unbound socket for non-zero sdif i.e. for packets in
a VRF, if tcp_l3mdev_accept is enabled.
Fixes: 3c82a21f4320 ("net: allow binding socket in a VRF when there's an unbound socket") Signed-off-by: Mike Manning <mvrmanning@gmail.com> Link: https://lore.kernel.org/netdev/a54c149aed38fded2d3b5fdb1a6c89e36a083b74.camel@lasnet.de/ Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 6dd9a14e92e5 ("net: Allow accepted sockets to be bound to l3mdev domain") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The authentication algorithm supports a maximum of 128-byte keys.
The allocated key memory is insufficient.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2") Signed-off-by: Kai Ye <yekai13@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without MODULE_DEVICE_TABLE, crypto_safexcel.ko module is not automatically
loaded on platforms where inside-secure crypto HW is specified in device
tree (e.g. Armada 3720). So add missing MODULE_DEVICE_TABLE for of.
MLX5E_MAX_RQ_NUM_MTTS should be the maximum value, so that
MLX5_MTT_OCTW(MLX5E_MAX_RQ_NUM_MTTS) fits into u16. The current value of
1 << 17 results in MLX5_MTT_OCTW(1 << 17) = 1 << 16, which doesn't fit
into u16. This commit replaces it with the maximum value that still
fits u16.
The driver reports whether TX/RX TLS device offloads are supported, but
not which ciphers/versions, these should be handled by returning
-EOPNOTSUPP when .tls_dev_add() is called.
Remove the WARN_ON kernel trace when the driver gets a request to
offload a cipher/version that is not supported as it is expected.
Not all DPB entries will be used most of the time. Unused entries will
thus have invalid timestamps. They will produce negative buffer index
which is not specifically handled. This works just by chance in current
code. It will even produce bogus pointer, but since it's not used, it
won't do any harm.
Let's fix that brittle design by skipping writing DPB entry altogether
if timestamp is invalid.
After successfull station association, if station queues are disabled for
some reason, the related lists are not emptied. So if some new element is
added to the list in iwl_mvm_mac_wake_tx_queue, it can match with the old
one and produce a BUG like this:
Commit 7a4836560a61 changes simple_write_to_buffer() with memdup_user()
but it forgets to change the value to be returned that came from
simple_write_to_buffer() call. It results in the following warning:
warning: variable 'rc' is uninitialized when used here [-Wuninitialized]
return rc;
^~
Remove rc variable and just return the passed in length if the
memdup_user() succeeds.
Cc: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: kernel test robot <lkp@intel.com> Fixes: 7a4836560a6198d245d5732e26f94898b12eb760 ("wifi: wil6210: debugfs: fix info leak in wil_write_file_wmi()") Fixes: ff974e4083341383d3dd4079e52ed30f57f376f0 ("wil6210: debugfs interface to send raw WMI command") Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220724202452.61846-1-ammar.faizi@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver") Signed-off-by: Liang He <windhl@126.com> Acked-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
After commit 3a5c7e4611dd, the variable errc is accessed before being
initialized, c.f. below W=2 warning:
| In function 'pch_can_error',
| inlined from 'pch_can_poll' at drivers/net/can/pch_can.c:739:4:
| drivers/net/can/pch_can.c:501:29: warning: 'errc' may be used uninitialized [-Wmaybe-uninitialized]
| 501 | cf->data[6] = errc & PCH_TEC;
| | ^
| drivers/net/can/pch_can.c: In function 'pch_can_poll':
| drivers/net/can/pch_can.c:484:13: note: 'errc' was declared here
| 484 | u32 errc, lec;
| | ^~~~
Moving errc initialization up solves this issue.
Fixes: 3a5c7e4611dd ("can: pch_can: do not report txerr and rxerr during bus-off") Reported-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/all/20220721160032.9348-1-mailhol.vincent@wanadoo.fr Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, data[5..7] of struct can_frame, when used as a CAN error
frame, are defined as being "controller specific". Device specific
behaviours are problematic because it prevents someone from writing
code which is portable between devices.
As a matter of fact, data[5] is never used, data[6] is always used to
report TX error counter and data[7] is always used to report RX error
counter. can-utils also relies on this.
This patch updates the comment in the uapi header to specify that
data[5] is reserved (and thus should not be used) and that data[6..7]
are used for error counters.
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family") Link: https://lore.kernel.org/all/20220719143550.3681-8-mailhol.vincent@wanadoo.fr CC: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The assignment of the value to the variable total in the loop
condition must be enclosed in additional parentheses, since otherwise,
in accordance with the precedence of the operators, the conjunction
will be performed first, and only then the assignment.
Due to this error, a warning later in the function after the loop may
not occur in the situation when it should.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru> Fixes: 0d4171e2153b ("p54: implement flush callback") Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220714134831.106004-1-subkhankulov@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful call to p54spi_request_firmware(), it
must be undone by a corresponding release_firmware() as already done in
the error handling path of p54spi_request_firmware() and in the .remove()
function.
Add the missing call in the error handling path and remove it from
p54spi_request_firmware() now that it is the responsibility of the caller
to release the firmware
The simple_write_to_buffer() function will succeed if even a single
byte is initialized. However, we need to initialize the whole buffer
to prevent information leaks. Just use memdup_user().
Fixes: ff974e408334 ("wil6210: debugfs interface to send raw WMI command") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/Ysg14NdKAZF/hcNG@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
The original direct splicing mechanism from Jens required the input to
be a regular file because it was avoiding the special socket case. It
also recognized blkdevs as being close enough to a regular file. But it
forgot about chardevs, which behave the same way and work fine here.
This is an okayish heuristic, but it doesn't totally work. For example,
a few chardevs should be spliceable here. And a few regular files
shouldn't. This patch fixes this by instead checking whether FMODE_LSEEK
is set, which represents decently enough what we need rewinding for when
splicing to internal pipes.
Fixes: b92ce5589374 ("[PATCH] splice: add direct fd <-> fd splicing support") Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 7337224fc150 ("bpf: Improve the info.func_info and info.func_info_rec_size behavior")
accidently made bpf_prog_ksym_set_name() conservative for bpf subprograms.
Fixed it so instead of "bpf_prog_tag_F" the stack traces print "bpf_prog_tag_full_subprog_name".
Fixes: 7337224fc150 ("bpf: Improve the info.func_info and info.func_info_rec_size behavior") Reported-by: Tejun Heo <tj@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20220714211637.17150-1-alexei.starovoitov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value from system() is a waitpid-style integer. Do not return
it directly because with the implicit masking in exit() it will always
return 0. Access it with appropriate macros to really pass on errors.
Fixes: 7290ce1423c3 ("selftests/timers: Add clocksource-switch test from timetest suite") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: John Stultz <jstultz@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
BPF map name is limited to BPF_OBJ_NAME_LEN.
A map name is defined as being longer than BPF_OBJ_NAME_LEN,
it will be truncated to BPF_OBJ_NAME_LEN when a userspace program
calls libbpf to create the map. A pinned map also generates a path
in the /sys. If the previous program wanted to reuse the map，
it can not get bpf_map by name, because the name of the map is only
partially the same as the name which get from pinned path.
The syscall information below show that map name "process_pinned_map"
is truncated to "process_pinned_".
bpf(BPF_OBJ_GET, {pathname="/sys/fs/bpf/process_pinned_map",
bpf_fd=0, file_flags=0}, 144) = -1 ENOENT (No such file or directory)
This patch check that if the name of pinned map are the same as the
actual name for the first (BPF_OBJ_NAME_LEN - 1),
bpf map still uses the name which is included in bpf object.
current code of __tcp_retransmit_skb only check TCP_SKB_CB(skb)->seq
in send window, and TCP_SKB_CB(skb)->seq_end maybe out of send window.
If receiver has shrunk his window, and skb is out of new window, it
should retransmit a smaller portion of the payload.
The mdp_ipi_comm structure defines a command that is either
PROCESS (start processing) or DEINIT (destroy instance); we
are using this one to send PROCESS or DEINIT commands from Linux
to an MDP instance through a VPU write but, while the first wants
us to stay 4-bytes aligned, the VPU instead requires an 8-bytes
data alignment.
Keeping in mind that these commands are executed immediately
after sending them (hence not chained with others before the
VPU/MDP "actually" start executing), it is fine to simply add
a padding of 4 bytes to this structure: this keeps the same
performance as before, as we're still stack-allocating it,
while avoiding hackery inside of mtk-vpu to ensure alignment
bringing a definitely bigger performance impact.
Fixes: c8eb2d7e8202 ("[media] media: Add Mediatek MDP Driver") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Houlong Wei <houlong.wei@mediatek.com> Reviewed-by: Irui Wang <irui.wang@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kunpeng920 encryption driver is used to deencrypt and decrypt
packets during the softirq, it is not allowed to use mutex lock. The
kernel will report the following error:
And the calltrace of task that actually caused kernel hungs as follows:
__switch_to+124
__schedule+548
schedule+72
schedule_timeout+348
__down_common+188
__down+24
down+104
hinic_get_stats64+44 [hinic]
dev_get_stats+92
bond_get_stats+172 [bonding]
dev_get_stats+92
dev_seq_printf_stats+60
dev_seq_show+24
seq_read_iter+964
seq_read+220
proc_reg_read+164
vfs_read+172
ksys_read+108
__arm64_sys_read+28
el0_svc_common+132
do_el0_svc+40
el0_svc+24
el0_sync_handler+164
el0_sync+324
When getting device stats from bond, kernel will call bond_get_stats().
It first holds the spinlock bond->stats_lock, and then call
hinic_get_stats64() to collect hinic device's stats.
However, hinic_get_stats64() calls `down(&nic_dev->mgmt_lock)` to
protect its critical section, which may schedule current task out.
And if system is under high pressure, the task cannot be woken up
immediately, which eventually triggers kernel hung panic.
Since previous patch has replaced hinic_dev.tx_stats/rx_stats with local
variable in hinic_get_stats64(), there is nothing need to be protected
by lock, so just removing down()/up() is ok.
Fixes: edd384f682cc ("net-next/hinic: Add ethtool and stats") Signed-off-by: Qiao Ma <mqaio@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function hinic_get_stats64() will do two operations:
1. reads stats from every hinic_rxq/txq and accumulates them
2. calls hinic_rxq/txq_clean_stats() to clean every rxq/txq's stats
For hinic_get_stats64(), it could get right data, because it sums all
data to nic_dev->rx_stats/tx_stats.
But it is wrong for get_drv_queue_stats(), this function will read
hinic_rxq's stats, which have been cleared to zero by hinic_get_stats64().
I have observed hinic's cleanup operation by using such command:
> watch -n 1 "cat ethtool -S eth4 | tail -40"
Result after a few seconds:
...
rxq7_pkts: 0
rxq7_bytes: 0
rxq7_errors: 0
rxq7_csum_errors: 0
rxq7_other_errors: 0
...
rxq9_pkts: 2
rxq9_bytes: 132
rxq9_errors: 0
rxq9_csum_errors: 0
rxq9_other_errors: 0
...
rxq11_pkts: 1
rxq11_bytes: 170
rxq11_errors: 0
rxq11_csum_errors: 0
rxq11_other_errors: 0
To solve this problem, we just keep every queue's total stats in their own
queue (aka hinic_{rxq|txq}), and simply sum all per-queue stats every time
calling hinic_get_stats64().
With that solution, there is no need to clean per-queue stats now,
and there is no need to maintain global hinic_dev.{tx|rx}_stats, too.
Fixes: edd384f682cc ("net-next/hinic: Add ethtool and stats") Signed-off-by: Qiao Ma <mqaio@linux.alibaba.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'vlan_bitmap' is a bitmap and is used as such. So allocate it with
devm_bitmap_zalloc() and its explicit bit size (i.e. VLAN_N_VID).
This avoids the need of the VLAN_BITMAP_SIZE macro which:
- needlessly has a 'nic_dev' parameter
- should be "long" (and not byte) aligned, so that the bitmap semantic
is respected
This is in fact not an issue because VLAN_N_VID is 4096 at the time
being, but devm_bitmap_zalloc() is less verbose and easier to understand.
The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.
This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.
Fixes: e19e9c692f81 ("drm/bridge/sii8620: add support for burst eMSC transmissions") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible for users to try to duplicate the CRTC state even when the
state doesn't exist. drm_atomic_helper_crtc_duplicate_state() (and other
users of __drm_atomic_helper_crtc_duplicate_state()) already guard this
with a WARN_ON() instead of crashing, so let's do that here too.
Currently, xsk_socket__delete frees BPF resources regardless of ctx
refcount. Xdpxceiver has a test to verify whether underlying BPF
resources would not be wiped out after closing XSK socket that was
bound to interface with other active sockets. From library's xsk part
perspective it also means that the internal xsk context is shared and
its refcount is bumped accordingly.
After a switch to loading XDP prog based on previously opened XSK
socket, mentioned xdpxceiver test fails with:
not ok 16 [xdpxceiver.c:swap_xsk_resources:1334]: ERROR: 9/"Bad file descriptor
which means that in swap_xsk_resources(), xsk_socket__delete() released
xskmap which in turn caused a failure of xsk_socket__update_xskmap().
To fix this, when deleting socket, decrement ctx refcount before
releasing BPF resources and do so only when refcount dropped to 0 which
means there are no more active sockets for this ctx so BPF resources can
be freed safely.
Fixes: 2f6324a3937f ("libbpf: Support shared umems between queues and devices") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20220629143458.934337-5-maciej.fijalkowski@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
ld: arch/arm64/crypto/ghash-ce-glue.o: in function 'ghash_ce_mod_exit':
ghash-ce-glue.c:(.exit.text+0x24): undefined reference to 'crypto_unregister_aead'
ld: arch/arm64/crypto/ghash-ce-glue.o: in function 'ghash_ce_mod_init':
ghash-ce-glue.c:(.init.text+0x34): undefined reference to 'crypto_register_aead'
Fixes: 537c1445ab0b ("crypto: arm64/gcm - implement native driver using v8 Crypto Extensions") Signed-off-by: Qian Cai <quic_qiancai@quicinc.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.
Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.
Fixes: 682e62c45406 ("drm/vc4: Fix support for interlaced modes on HDMI.") Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com> Link: https://lore.kernel.org/r/20220613144800.326124-31-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike the previous generations, the HSM clock limitation is way above
what we can reach without scrambling, so let's move the maximum
frequency we support to the maximum clock frequency without scrambling.
drm_atomic_helper_connector_reset uses kmalloc which, from an API
standpoint, can fail, and thus setting connector->state to NULL.
However, our reset hook then calls drm_atomic_helper_connector_tv_reset
that will access connector->state without checking if it's a valid
pointer or not.
Make sure we don't end up accessing a NULL pointer.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-5-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
vc4_dsi_encoder_disable is partially an open coded version of
drm_bridge_chain_disable, but it missed a termination condition
in the loop for ->disable which meant that no post_disable
calls were made.
DSI0 seemingly had very little or no testing as a load of
the register mappings were incorrect/missing, so host
transfers always timed out due to enabling/checking incorrect
bits in the interrupt enable and status registers.
Fixes: 4078f5757144 ("drm/vc4: Add DSI driver") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-16-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
vc4_dsi was registering both dsi0 and dsi1 as VC4_ENCODER_TYPE_DSI1
which seemed to work OK for a single DSI display, but fails
if there are two DSI displays connected.
Update to register the correct type.
Fixes: 4078f5757144 ("drm/vc4: Add DSI driver") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-15-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most of the differences between DSI0 and DSI1 are handled through the
ID. However, the BCM2711 DSI is going to introduce one more variable to
the mix and will break some expectations of the earlier, simpler, test.
Let's add a variant structure that will address most of the differences
between those three controllers.
The DSI clocks setup function has been using an array to store the clock
name of either the DSI0 or DSI1 blocks, using the port ID to choose the
proper one.
Let's switch to an snprintf call to do the same thing and simplify the
array a bit.
For slightly unknown reasons, dsi0 takes a different pixel format
to dsi1, and that has to be set in the pixel valve.
Amend the setup accordingly.
Fixes: a86773d120d7 ("drm/vc4: Add support for feeding DSI encoders from the pixel valve.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-14-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.
The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying. This allows
for slower link frequencies on the DSI bus where the resolution permits.
Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.
Fixes: 86c1b9eff3f2 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log