Dave Airlie [Fri, 21 Jun 2024 00:49:58 +0000 (10:49 +1000)]
Merge tag 'drm-misc-next-2024-06-13' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for 6.11:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Sprinkle MODULE_DESCRIPTIONS everywhere they are missing
- bridge: Remove drm_bridge_chain_mode_fixup
- ci: Require a more recent version of mesa, improve farm estup and
test generation
- mipi-dbi: Remove mipi_dbi_machine_little_endian, make SPI bits per
word configurable, support RGB888, and allow pixel formats to be
specified in the DT.
- mm: Remove drm_mm_replace_node
- panic: Allow to dump kmsg to the screen
- print: Add a drm prefix to warn level messages too, remove
___drm_dbg, consolidate prefix handling
Driver Changes:
- sun4i: Rework the blender setup for DE2
- bridges:
- bridge-connector: Plumb in the new HDMI helpers
- samsung-dsim: Fix timings calculation
- tc358767: Plenty of small fixes
- panels:
- More cleanup of prepare / enable state tracking in drivers
- New panel: PrimeView PM070WL4,
Dave Airlie [Fri, 21 Jun 2024 00:31:14 +0000 (10:31 +1000)]
Merge tag 'drm-misc-next-2024-06-06' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for 6.10:
UAPI Changes:
Cross-subsystem Changes:
- dma-buf: Warn when reserving 0 fence slots, internal API
enhancements for heaps
Core Changes:
Driver Changes:
- atmel-hlcdc: Support XLCDC in sam9x7
- msm: Validate registers XML description against schema in CI
- v3d: Fix build warning
- bridges:
- analogix_dp: Various improvements
- panels:
- New panel: WL-355608-A8
Dave Airlie [Fri, 14 Jun 2024 07:18:29 +0000 (17:18 +1000)]
Merge tag 'drm-misc-next-2024-05-30' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for 6.11:
UAPI Changes:
- Deprecate DRM date and return a 0 date in DRM_IOCTL_VERSION
Core Changes:
- connector: Create a set of helpers to help with HDMI support
- fbdev: Create memory manager optimized fbdev emulation
- panic: Allow to select fonts, improve drm_fb_dma_get_scanout_buffer
Driver Changes:
- Remove driver owner assignments
- Allow more drivers to compile with COMPILE_TEST
- Conversions to drm_edid
- ivpu: hardware scheduler support, profiling support, improvements
to the platform support layer
- mgag200: general reworks and improvements
- nouveau: Add NVreg_RegistryDwords command line option
- rockchip: Conversion to the hdmi helpers
- sun4i: Conversion to the hdmi helpers
- vc4: Conversion to the hdmi helpers
- v3d: Perf counters improvements
- zynqmp: IRQ and debugfs improvements
- bridge:
- Remove redundant checks on bridge->encoder
- panels:
- Switch panels from register table initialization to proper code
- Now that the panel code tracks the panel state, remove every
ad-hoc implementation in the panel drivers
- New panels: Lincoln Tech Sol LCD185-101CT, Microtips Technology
13-101HIEBCAF0-C, Microtips Technology MF-103HIEB0GA0, BOE
nv110wum-l60, IVO t109nw41
Tejas Vipin [Wed, 12 Jun 2024 13:35:43 +0000 (19:05 +0530)]
drm/mipi-dsi: fix handling of ctx in mipi_dsi_msleep
ctx would be better off treated as a pointer to account for most of its
usage so far, and brackets should be added to account for operator
precedence for correct evaluation.
Dmitry Baryshkov [Fri, 7 Jun 2024 13:23:00 +0000 (16:23 +0300)]
drm/bridge-connector: implement glue code for HDMI connector
In order to let bridge chains implement HDMI connector infrastructure,
add necessary glue code to the drm_bridge_connector. In case there is a
bridge that sets DRM_BRIDGE_OP_HDMI, drm_bridge_connector will register
itself as a HDMI connector and provide proxy drm_connector_hdmi_funcs
implementation.
Note, to simplify implementation, there can be only one bridge in a
chain that sets DRM_BRIDGE_OP_HDMI. Setting more than one is considered
an error. This limitation can be lifted later, if the need arises.
Dmitry Baryshkov [Fri, 7 Jun 2024 13:22:59 +0000 (16:22 +0300)]
drm/bridge-connector: switch to using drmm allocations
Turn drm_bridge_connector to using drmm_kzalloc() and
drmm_connector_init() and drop the custom destroy function. The
drm_connector_unregister() and fwnode_handle_put() are already handled
by the drm_connector_cleanup() and so are safe to be dropped.
Add drm_atomic_helper_connector_hdmi_disable_audio_infoframe(), an API
to allow the driver disable sending the Audio Infoframe. This is to be
used by the drivers if setup of the infoframes is not tightly coupled
with the audio functionality and just disabling the audio playback
doesn't stop the HDMI hardware from sending the Infoframe.
Douglas Anderson [Wed, 5 Jun 2024 00:23:08 +0000 (17:23 -0700)]
drm/panel: raydium-rm67191: Don't call unprepare+disable at shutdown
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
A grep through mainline for compatible strings used by this driver
indicates that it is used by IMX boards. The IMX driver appears to be
correctly calling drm_atomic_helper_shutdown() so we can remove the
calls.
Douglas Anderson [Wed, 5 Jun 2024 00:23:07 +0000 (17:23 -0700)]
drm/panel: raydium-rm67191: Stop tracking enabled
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
The conversion of the rm67191 panel driver follows many of the other
panel drivers but has a few differences that need to be called out.
Like in commit 1e0465eb16a4 ("drm/panel: otm8009a: Don't double check
prepared/enabled"), this panel also uses the "prepared" flag to
prevent the backlight functions from running when the panel is powered
off. This is probably not the safest thing to do but the old behavior
was preserved. See the discussion in the otm8009a patch. Because of
this, I've left the driver tracking "prepared" but removed its
tracking of "enabled".
NOTE: as part of this, transition the panel's direct calls to its
disable/unprepare functions in shutdown to call through DRM panel.
Douglas Anderson [Wed, 5 Jun 2024 00:23:06 +0000 (17:23 -0700)]
drm/panel: sharp-ls043t1le01: Don't call disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
A grep through mainline for compatible strings used by this driver
indicates that it is used by Qualcomm boards. The Qualcomm driver
appears to be correctly calling drm_atomic_helper_shutdown() so we can
remove the calls.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:23:04 +0000 (17:23 -0700)]
drm/panel: sharp-lq101r1sx01: Don't call disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
A grep through mainline for compatible strings used by this driver
indicates that it is used by Tegra boards. The Tegra driver appears to
be correctly calling drm_atomic_helper_shutdown() so we can remove the
calls.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:23:02 +0000 (17:23 -0700)]
drm/panel: seiko-43wvf1g: Don't call disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
A grep through mainline for compatible strings used by this driver
indicates that it is used by IMX boards. As far as I can tell, all IMX
boards are now correctly calling drm_atomic_helper_shutdown() so we
can remove the calls.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:23:00 +0000 (17:23 -0700)]
drm/panel: panasonic-vvx10f034n00: Don't call disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
Unfortunately, grepping mainline for this panel's compatible string
shows no hits, so we can't be 100% sure if the DRM modeset driver used
with this panel has been fixed. If it is found that the DRM modeset
driver hasn't been fixed then this patch could be temporarily reverted
until it is.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:22:58 +0000 (17:22 -0700)]
drm/panel: jdi-lt070me05000: Don't call disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
A grep through mainline for compatible strings used by this driver
indicates that it is used by Qualcomm boards. The Qualcomm driver
appears to be correctly calling drm_atomic_helper_shutdown() so we can
remove the calls.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
NOTE: as part of this, transition the panel's direct calls to its
disable function in shutdown/remove to call through DRM panel.
Douglas Anderson [Wed, 5 Jun 2024 00:22:56 +0000 (17:22 -0700)]
drm/panel: tdo-tl070wsh30: Don't call unprepare+disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
Unfortunately, grepping mainline for this panel's compatible string
shows no hits, so we can't be 100% sure if the DRM modeset driver used
with this panel has been fixed. If it is found that the DRM modeset
driver hasn't been fixed then this patch could be temporarily reverted
until it is.
Douglas Anderson [Wed, 5 Jun 2024 00:22:55 +0000 (17:22 -0700)]
drm/panel: tdo-tl070wsh30: Stop tracking prepared
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:22:54 +0000 (17:22 -0700)]
drm/panel: osd-osd101t2587-53ts: Don't call unprepare+disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
A grep through mainline for compatible strings used by this driver
indicates that it is used by TI OMAP boards. The OMAP driver appears
to be correctly calling drm_atomic_helper_shutdown() so we can remove
the calls.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:22:52 +0000 (17:22 -0700)]
drm/panel: olimex-lcd-olinuxino: Don't call unprepare+disable at remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
Unfortunately, grepping mainline for this panel's compatible string
shows no hits, so we can't be 100% sure if the DRM modeset driver used
with this panel has been fixed. If it is found that the DRM modeset
driver hasn't been fixed then this patch could be temporarily reverted
until it is.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:22:50 +0000 (17:22 -0700)]
drm/panel: khadas-ts050: Don't call unprepare+disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
Unfortunately, grepping mainline for this panel's compatible string
shows no hits, so we can't be 100% sure if the DRM modeset driver used
with this panel has been fixed. If it is found that the DRM modeset
driver hasn't been fixed then this patch could be temporarily reverted
until it is.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
Douglas Anderson [Wed, 5 Jun 2024 00:22:48 +0000 (17:22 -0700)]
drm/panel: boe-himax8279d: Don't call unprepare+disable at shutdown/remove
It's the responsibility of a correctly written DRM modeset driver to
call drm_atomic_helper_shutdown() at shutdown time and that should be
disabling / unpreparing the panel if needed. Panel drivers shouldn't
be calling these functions themselves.
A recent effort was made to fix as many DRM modeset drivers as
possible [1] [2] [3] and most drivers are fixed now.
Unfortunately, grepping mainline for this panel's compatible string
shows no hits, so we can't be 100% sure if the DRM modeset driver used
with this panel has been fixed. If it is found that the DRM modeset
driver hasn't been fixed then this patch could be temporarily reverted
until it is.
As talked about in commit d2aacaf07395 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
NOTE: as part of this, transition the panel's direct calls to its
disable/unprepare functions in shutdown/remove to call through DRM
panel.
Display (i915):
- Add missing include to intel_vga.c (Michal Wajdeczko)
Driver Changes:
- Fix Display (xe-only) detection for ADL-N (Lucas)
- Runtime PM fixes that enabled PC-10 and D3Cold (Francois, Rodrigo)
- Fix unexpected silent drm backmerge issues (Thomas)
- More (a lot more) preparation for SR-IOV support (Michal Wajdeczko)
- Devcoredump fixes and improvements (Jose, Tejas, Matt Brost)
- Introduce device 'wedged' state (Rodrigo)
- Improve debug and info messages (Michal Wajdeczko, Rodrigo, Nirmoy)
- Adding or fixing workarounds (Tejas, Shekhar, Lucas, Bommu)
- Check result of drmm_mutex_init (Michal Wajdeczko)
- Enlarge the critical dma fence area for preempt fences (Matt Auld)
- Prevent UAF in VM's rebind work (Matt Auld)
- GuC submit related clean-ups and fixes (Matt Brost, Himal, Jonathan, Niranjana)
- Prefer local helpers to perform dma reservation locking (Himal)
- Spelling and typo fixes (Colin, Francois)
- Prep patches for 1 job per VM bind IOCTL (no uapi change yet) (Matt Brost)
- Remove uninitialized end var from xe_gt_tlb_invalidation_range (Nirmoy)
- GSC related changes targeting LNL support (Daniele)
- Fix assert in L3 bank mask generation (Francois)
- Perform dma_map when moving system buffer objects to TT (Thomas)
- Add helpers for manipulating macro arguments (Michal Wajdeczko)
- Refactor default device atomic settings (Nirmoy)
- Add debugfs node to dump mocs (Janga)
- Use ordered WQ for G2H handler (Matt Brost)
- Clean up and fixes in header includes (Michal Wajdeczko)
- Prefer flexible-array over deprecated zero-lenght ones (Lucas)
- Add Indirect Ring State support (Niranjana)
- Fix UBSAN shift-out-of-bounds failure (Shuicheng)
- HWMon fixes and additions (Karthik)
- Clean-up refactor around probe init functions (Lucas, Michal Wajdeczko)
- Fix PCODE init function (Himal)
- Only use reserved BCS instances for usm migrate exec queue (Matt Brost)
- Only zap PTEs as needed (Matt Brost)
- Per client usage info (Lucas)
- Core hotunplug improvements converting stuff towards devm (Matt Auld)
- Don't emit false error if running in execlist mode (Michal Wajdeczko)
- Remove unused struct (Dr. David)
- Support/debug for slow GuC loads (John Harrison)
- Decouple job seqno and lrc seqno (Matt Brost)
- Allow migrate vm gpu submissions from reclaim context (Thomas)
- Rename drm-client running time to run_ticks and fix a UAF (Umesh)
- Check empty pinned BO list with lock held (Nirmoy)
- Drop undesired prefix from the platform name (Michal Wajdeczko)
- Remove unwanted mutex locking on xe file close (Niranjana)
- Replace format-less snprintf() with strscpy() (Arnd)
- Other general clean-ups on registers definitions and function names (Michal Wajdeczko)
- Add kernel-doc to some xe_lrc interfaces (Niranajana)
- Use missing lock in relay_needs_worker (Nirmoy)
- Drop redundant W=1 warnings from Makefile (Jani)
- Simplify if condition in preempt fences code (Thorsten)
- Flush engine buffers before signalling user fence on all engines (Andrzej)
- Don't overmap identity VRAM mapping (Matt Brost)
- Do not dereference NULL job->fence in trace points (Matt Brost)
- Add synchronous gt reset debugfs (Jonathan)
- Xe gt_idle fixes (Riana)
The VFP, HBP, and HSA are divided between the available lanes if
there is more than one lane. For certain timings and lane
configurations, the HFP may not be evenly divisible. If the HFP
is rounded down, it ends up being too small which can cause some
monitors to not sync properly. In these instances, adjust htotal
and hsync to round the HFP up, and recalculate the htotal.
This allows 720P-60 to operation on an i.MX8MP with a four-lane
configuration.
Adam Ford [Sat, 1 Jun 2024 14:41:01 +0000 (09:41 -0500)]
drm/bridge: samsung-dsim: Set P divider based on min/max of fin pll
The P divider should be set based on the min and max values of
the fin pll which may vary between different platforms.
These ranges are defined per platform, but hard-coded values
were used instead which resulted in a smaller range available
on the i.MX8M[MNP] than what was possible.
As noted by Frieder, there are descripencies between the reference
manuals of the Mini, Nano and Plus, so I reached out to my NXP
rep and got the following response regarding the varing notes
in the documentation.
"Yes it is definitely wrong, the one that is part of the NOTE in
MIPI_DPHY_M_PLLPMS register table against PMS_P, PMS_M and PMS_S is
not correct. I will report this to Doc team, the one customer should
be take into account is the Table 13-40 DPHY PLL Parameters and the
Note above."
With this patch, the clock rates now match the values used in NXP's
downstream kernel.
Fixes: 846307185f0f ("drm/bridge: samsung-dsim: update PLL reference clock") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Marek Vasut <marex@denx.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240601144103.198299-1-aford173@gmail.com
Marek Vasut [Fri, 31 May 2024 20:33:12 +0000 (22:33 +0200)]
drm/bridge: tc358767: Check if fully initialized before signalling HPD event via IRQ
Make sure the connector is fully initialized before signalling any
HPD events via drm_kms_helper_hotplug_event(), otherwise this may
lead to NULL pointer dereference.
Marek Vasut [Fri, 31 May 2024 20:32:01 +0000 (22:32 +0200)]
drm/bridge: tc358767: Fix comment in tc_edp_mode_valid
Fix comment copy-paste error in tc_edp_mode_valid(), this function
is validating DP/eDP clock, not DPI clock frequency. Update the
comment to match. No functional change.
Sam Ravnborg [Fri, 31 May 2024 20:37:45 +0000 (22:37 +0200)]
drm/mediatek: Drop chain_mode_fixup call in mode_valid()
The mode_valid implementation had a call to
drm_bridge_chain_mode_fixup() which would be wrong as the mode_valid is
not allowed to change anything - only to validate the mode.
As the next bridge is often/always a connector the call had no effect
anyway. So drop it.
From the git history I could see this call was included in the original
version of the driver so there was no help there to find out why it was
added in the first place. But a lot has changed since the initial driver
were added and is seems safe to remove the call now.
v4:
- Link to v3: https://lore.kernel.org/dri-devel/20220717174454.46616-4-sam@ravnborg.org/
- Rebase, and added acks/rb
v3:
- Link to v2: https://lore.kernel.org/dri-devel/20211020181901.2114645-6-sam@ravnborg.org/
v2:
- Link to v1: https://lore.kernel.org/dri-devel/20210722062246.2512666-6-sam@ravnborg.org/
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Cc: linux-mediatek@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240531-bridge_chain_mode-v1-1-8b49e36c5dd3@ravnborg.org
Jocelyn Falempe [Mon, 3 Jun 2024 09:47:27 +0000 (11:47 +0200)]
drm/panic: Add a kmsg panic screen
Add a kmsg option, which will display the last lines of kmsg,
and should be similar to fbcon.
Add a drm.panic_screen module parameter, so you can choose between
the different panic screens available.
two options currently, but more will be added later:
* "user": a short message telling the user to reboot the machine.
* "kmsg": fill the screen with the last lines of kmsg.
You can even change it at runtime by writing to
/sys/module/drm/parameters/panic_screen
v2:
* Use module parameter instead of Kconfig choice
(Javier Martinez Canillas)
v3:
* Add help for module parameter usage in Kconfig
(Javier Martivez Canillas)
* Fix use of font->height before checking it isn't null.
(kernel test robot, Dan Carpenter)
Jocelyn Falempe [Mon, 3 Jun 2024 09:47:25 +0000 (11:47 +0200)]
drm/panic: only draw the foreground color in drm_panic_blit()
The whole framebuffer is cleared, so it's useless to rewrite the
background colored pixels. It allows to simplify the drawing
functions, and prepare the work for the set_pixel() callback.
v2:
* keep fg16/fg24/fg32 as variable name for the blit function.
* add drm_panic_is_pixel_fg() to avoid code duplication.
both suggested by Javier Martinez Canillas
Identical configurations of planes can lead to different (and wrong)
layer -> pipe routing at HW level, depending on the order of atomic
plane changes.
For example:
- Layer 1 is configured to zpos 0 and thus uses pipe 0. No other layer
is enabled. This is a typical situation at boot.
- When a compositor takes over and layer 3 is enabled,
sun8i_ui_layer_enable() will get called with old_zpos=0 zpos=1, which
will lead to incorrect disabling of pipe 0 and enabling of pipe 1.
What happens is that sun8i_ui_layer_enable() function may disable
blender pipes even if it is no longer assigned to its layer.
To correct this, move the routing setup out of individual plane's
atomic_update into crtc's atomic_update, where it can be calculated
and updated all at once.
Remove the atomic_disable callback because it is no longer needed.
Ondrej Jirman [Sat, 24 Feb 2024 15:05:58 +0000 (16:05 +0100)]
drm/sun4i: Unify sun8i_*_layer structs
These structs are identical, use a single struct to represent private
data for the DRM plane. This is a preparation for configuring layer
routing from the CRTC (mixer) instead of current approach of setting
up routing from individual layer's atomic_update callback.
Signed-off-by: Ondrej Jirman <megi@xff.cz> Reviewed-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/20240224150604.3855534-2-megi@xff.cz Signed-off-by: Maxime Ripard <mripard@kernel.org>
Jeff Johnson [Sun, 9 Jun 2024 18:42:53 +0000 (11:42 -0700)]
drm: add missing MODULE_DESCRIPTION() macros
On x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/gud/gud.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/drm_panel_orientation_quirks.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/drm_mipi_dbi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/i915/kvmgt.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/udl/udl.o
Add the missing invocation of the MODULE_DESCRIPTION() macro to all
files which have a MODULE_LICENSE().
For consistency this includes drivers/gpu/drm/drm_simple_kms_helper.c
since it contains a MODULE_LICENSE() even though it isn't built as a
separate module -- it is always built as part of drm_kms_helper and
drm_kms_helper_common.c already provides a MODULE_DESCRIPTION for that
module.
Jeff Johnson [Sun, 9 Jun 2024 17:20:27 +0000 (10:20 -0700)]
drm/tiny: add missing MODULE_DESCRIPTION() macros
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/tiny/bochs.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/tiny/cirrus.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpu/drm/tiny/gm12u320.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Linus Torvalds [Sun, 9 Jun 2024 16:04:51 +0000 (09:04 -0700)]
Merge tag 'perf-tools-fixes-for-v6.10-2-2024-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Update copies of kernel headers, which resulted in support for the
new 'mseal' syscall, SUBVOL statx return mask bit, RISC-V and PPC
prctls, fcntl's DUPFD_QUERY, POSTED_MSI_NOTIFICATION IRQ vector,
'map_shadow_stack' syscall for x86-32.
- Revert perf.data record memory allocation optimization that ended up
causing a regression, work is being done to re-introduce it in the
next merge window.
- Fix handling of minimal vmlinux.h file used with BPF's CO-RE when
interrupting the build.
* tag 'perf-tools-fixes-for-v6.10-2-2024-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
perf bpf: Fix handling of minimal vmlinux.h file when interrupting the build
Revert "perf record: Reduce memory for recording PERF_RECORD_LOST_SAMPLES event"
tools headers arm64: Sync arm64's cputype.h with the kernel sources
tools headers uapi: Sync linux/stat.h with the kernel sources to pick STATX_SUBVOL
tools headers UAPI: Update i915_drm.h with the kernel sources
tools headers UAPI: Sync kvm headers with the kernel sources
tools arch x86: Sync the msr-index.h copy with the kernel sources
tools headers: Update the syscall tables and unistd.h, mostly to support the new 'mseal' syscall
perf trace beauty: Update the arch/x86/include/asm/irq_vectors.h copy with the kernel sources to pick POSTED_MSI_NOTIFICATION
perf beauty: Update copy of linux/socket.h with the kernel sources
tools headers UAPI: Sync fcntl.h with the kernel sources to pick F_DUPFD_QUERY
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools include UAPI: Sync linux/stat.h with the kernel sources
Linus Torvalds [Sun, 9 Jun 2024 15:49:13 +0000 (08:49 -0700)]
Merge tag 'edac_urgent_for_v6.10_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fixes from Borislav Petkov:
- Convert PCI core error codes to proper error numbers since latter get
propagated all the way up to the module loading functions
* tag 'edac_urgent_for_v6.10_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/igen6: Convert PCIBIOS_* return codes to errnos
EDAC/amd64: Convert PCIBIOS_* return codes to errnos
Linus Torvalds [Sun, 9 Jun 2024 02:14:02 +0000 (19:14 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for the SiFive PRCI clocks so that the device boots again.
This driver was registering clkdev lookups that were always going to
be useless. This wasn't a problem until clkdev started returning an
error in these cases, causing this driver to fail probe, and thus boot
to fail because clks are essential for most drivers. The fix is
simple, don't use clkdev because this is a DT based system where
clkdev isn't used"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sifive: Do not register clkdevs for PRCI clocks
Linus Torvalds [Sun, 9 Jun 2024 02:07:18 +0000 (19:07 -0700)]
Merge tag '6.10-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
"Two small smb3 client fixes:
- fix deadlock in umount
- minor cleanup due to netfs change"
* tag '6.10-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Don't advance the I/O iterator before terminating subrequest
smb: client: fix deadlock in smb2_find_smb_tcon()
Linus Torvalds [Sat, 8 Jun 2024 17:12:33 +0000 (10:12 -0700)]
Merge tag 'kbuild-fixes-v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix the initial state of the save button in 'make gconfig'
- Improve the Kconfig documentation
- Fix a Kconfig bug regarding property visibility
- Fix build breakage for systems where 'sed' is not installed in /bin
- Fix a false warning about missing MODULE_DESCRIPTION()
* tag 'kbuild-fixes-v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: do not warn about missing MODULE_DESCRIPTION() for vmlinux.o
kbuild: explicitly run mksysmap as sed script from link-vmlinux.sh
kconfig: remove wrong expr_trans_bool()
kconfig: doc: document behavior of 'select' and 'imply' followed by 'if'
kconfig: doc: fix a typo in the note about 'imply'
kconfig: gconf: give a proper initial state to the Save button
kconfig: remove unneeded code for user-supplied values being out of range
Linus Torvalds [Sat, 8 Jun 2024 16:57:09 +0000 (09:57 -0700)]
Merge tag 'media/v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fixes for the new ipu6 driver (and related fixes to mei csi driver)
- fix a double debugfs remove logic at mgb4 driver
- a documentation fix
* tag 'media/v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: intel/ipu6: add csi2 port sanity check in notifier bound
media: intel/ipu6: update the maximum supported csi2 port number to 6
media: mei: csi: Warn less verbosely of a missing device fwnode
media: mei: csi: Put the IPU device reference
media: intel/ipu6: fix the buffer flags caused by wrong parentheses
media: intel/ipu6: Fix an error handling path in isys_probe()
media: intel/ipu6: Move isys_remove() close to isys_probe()
media: intel/ipu6: Fix some redundant resources freeing in ipu6_pci_remove()
media: Documentation: v4l: Fix ACTIVE route flag
media: mgb4: Fix double debugfs remove
Linus Torvalds [Sat, 8 Jun 2024 16:44:50 +0000 (09:44 -0700)]
Merge tag 'irq-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
- Fix possible memory leak the riscv-intc irqchip driver load failures
- Fix boot crash in the sifive-plic irqchip driver caused by recently
changed boot initialization order
- Fix race condition in the gic-v3-its irqchip driver
* tag 'irq-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix potential race condition in its_vlpi_prop_update()
irqchip/sifive-plic: Chain to parent IRQ after handlers are ready
irqchip/riscv-intc: Prevent memory leak when riscv_intc_init_common() fails
Linus Torvalds [Sat, 8 Jun 2024 16:36:08 +0000 (09:36 -0700)]
Merge tag 'x86-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Miscellaneous fixes:
- Fix kexec() crash if call depth tracking is enabled
- Fix SMN reads on inaccessible registers on certain AMD systems"
* tag 'x86-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/amd_nb: Check for invalid SMN reads
x86/kexec: Fix bug with call depth tracking
Linus Torvalds [Sat, 8 Jun 2024 16:26:59 +0000 (09:26 -0700)]
Merge tag 'perf-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf event fix from Ingo Molnar:
"Fix race between perf_event_free_task() and perf_event_release_kernel()
that can result in missed wakeups and hung tasks"
* tag 'perf-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix missing wakeup when waiting for context reference
Linus Torvalds [Sat, 8 Jun 2024 16:03:46 +0000 (09:03 -0700)]
Merge tag 'locking-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking doc fix from Ingo Molnar:
"Fix typos in the kerneldoc of some of the atomic APIs"
* tag 'locking-urgent-2024-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/atomic: scripts: fix ${atomic}_sub_and_test() kerneldoc
Linus Torvalds [Sat, 8 Jun 2024 00:01:10 +0000 (17:01 -0700)]
Merge tag 'mm-hotfixes-stable-2024-06-07-15-24' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"14 hotfixes, 6 of which are cc:stable.
All except the nilfs2 fix affect MM and all are singletons - see the
chagelogs for details"
* tag 'mm-hotfixes-stable-2024-06-07-15-24' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
nilfs2: fix nilfs_empty_dir() misjudgment and long loop on I/O errors
mm: fix xyz_noprof functions calling profiled functions
codetag: avoid race at alloc_slab_obj_exts
mm/hugetlb: do not call vma_add_reservation upon ENOMEM
mm/ksm: fix ksm_zero_pages accounting
mm/ksm: fix ksm_pages_scanned accounting
kmsan: do not wipe out origin when doing partial unpoisoning
vmalloc: check CONFIG_EXECMEM in is_vmalloc_or_module_addr()
mm: page_alloc: fix highatomic typing in multi-block buddies
nilfs2: fix potential kernel bug due to lack of writeback flag waiting
memcg: remove the lockdep assert from __mod_objcg_mlstate()
mm: arm64: fix the out-of-bounds issue in contpte_clear_young_dirty_ptes
mm: huge_mm: fix undefined reference to `mthp_stats' for CONFIG_SYSFS=n
mm: drop the 'anon_' prefix for swap-out mTHP counters
Linus Torvalds [Fri, 7 Jun 2024 23:54:57 +0000 (16:54 -0700)]
Merge tag 'gpio-fixes-for-v6.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- interrupt handling and Kconfig fixes for gpio-tqmx86
- add a buffer for storing output values in gpio-tqmx86 as reading back
the registers always returns the input values
- add missing MODULE_DESCRIPTION()s to several GPIO drivers
* tag 'gpio-fixes-for-v6.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: add missing MODULE_DESCRIPTION() macros
gpio: tqmx86: fix broken IRQ_TYPE_EDGE_BOTH interrupt type
gpio: tqmx86: store IRQ trigger type and unmask status separately
gpio: tqmx86: introduce shadow register for GPIO output value
gpio: tqmx86: fix typo in Kconfig label
Linus Torvalds [Fri, 7 Jun 2024 23:45:48 +0000 (16:45 -0700)]
Merge tag 'block-6.10-20240607' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix for null_blk block size validation (Andreas)
- NVMe pull request via Keith:
- Use reserved tags for special fabrics operations (Chunguang)
- Persistent Reservation status masking fix (Weiwen)
* tag 'block-6.10-20240607' of git://git.kernel.dk/linux:
null_blk: fix validation of block size
nvme: fix nvme_pr_* status code parsing
nvme-fabrics: use reserved tag for reg read/write command
Linus Torvalds [Fri, 7 Jun 2024 23:43:07 +0000 (16:43 -0700)]
Merge tag 'io_uring-6.10-20240607' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Fix a locking order issue with setting max async thread workers
(Hagar)
- Fix for a NULL pointer dereference for failed async flagged requests
using ring provided buffers. This doesn't affect the current kernel,
but it does affect older kernels, and is being queued up for 6.10
just to make the stable process easier (me)
- Fix for NAPI timeout calculations for how long to busy poll, and
subsequently how much to sleep post that if a wait timeout is passed
in (me)
- Fix for a regression in this release cycle, where we could end up
using a partially unitialized match value for io-wq (Su)
* tag 'io_uring-6.10-20240607' of git://git.kernel.dk/linux:
io_uring: fix possible deadlock in io_register_iowq_max_workers()
io_uring/io-wq: avoid garbage value of 'match' in io_wq_enqueue()
io_uring/napi: fix timeout calculation
io_uring: check for non-NULL file pointer in io_file_can_poll()
Linus Torvalds [Fri, 7 Jun 2024 22:13:12 +0000 (15:13 -0700)]
Merge tag 'for-6.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix handling of folio private changes.
The private value holds pointer to our extent buffer structure
representing a metadata range. Release and create of the range was
not properly synchronized when updating the private bit which ended
up in double folio_put, leading to all sorts of breakage
- fix a crash, reported as duplicate key in metadata, but caused by a
race of fsync and size extending write. Requires prealloc target
range + fsync and other conditions (log tree state, timing)
- fix leak of qgroup extent records after transaction abort
* tag 'for-6.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: protect folio::private when attaching extent buffer folios
btrfs: fix leak of qgroup extent records after transaction abort
btrfs: fix crash on racing fsync and size-extending write into prealloc
Linus Torvalds [Fri, 7 Jun 2024 21:47:38 +0000 (14:47 -0700)]
Merge tag 'riscv-for-linus-6.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- Another fix to avoid allocating pages that overlap with ERR_PTR,
which manifests on rv32
- A revert for the badaccess patch I incorrectly picked up an early
version of
* tag 'riscv-for-linus-6.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
Revert "riscv: mm: accelerate pagefault when badaccess"
riscv: fix overlap of allocated page and PTR_ERR
Linus Torvalds [Fri, 7 Jun 2024 21:44:53 +0000 (14:44 -0700)]
Merge tag 's390-6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Do not create PT_LOAD program header for the kenel image when the
virtual memory informaton in OS_INFO data is not available. That
fixes stand-alone dump failures against kernels that do not provide
the virtual memory informaton
- Add KVM s390 shared zeropage selftest
* tag 's390-6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
KVM: s390x: selftests: Add shared zeropage test
s390/crash: Do not use VM info if os_info does not have it
Linus Torvalds [Fri, 7 Jun 2024 21:36:57 +0000 (14:36 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix spurious CPU hotplug warning message from SETEND emulation code
- Fix the build when GCC wasn't inlining our I/O accessor internals
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/io: add constant-argument check
arm64: armv8_deprecated: Fix warning in isndep cpuhp starting process
Linus Torvalds [Fri, 7 Jun 2024 21:13:46 +0000 (14:13 -0700)]
Merge tag 'platform-drivers-x86-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Default silead touchscreen driver to 10 fingers and drop 10 finger
setting from all DMI quirks. More of a cleanup then a pure fix, but
since the DMI quirks always get updated through the fixes branch
this avoids conflicts.
- Kconfig fix for randconfig builds
- dell-smbios: Fix wrong token data in sysfs
- amd-hsmp: Fix driver poking unsupported hw when loaded manually
* tag 'platform-drivers-x86-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/amd/hsmp: Check HSMP support on AMD family of processors
platform/x86: dell-smbios: Simplify error handling
platform/x86: dell-smbios: Fix wrong token data in sysfs
platform/x86: yt2-1380: add CONFIG_EXTCON dependency
platform/x86: touchscreen_dmi: Use 2-argument strscpy()
platform/x86: touchscreen_dmi: Drop "silead,max-fingers" property
Input: silead - Always support 10 fingers
Linus Torvalds [Fri, 7 Jun 2024 20:34:53 +0000 (13:34 -0700)]
Merge tag 'iommu-fixes-v6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Core:
- Make iommu-dma code recognize 'force_aperture' again
- Fix for potential NULL-ptr dereference from iommu_sva_bind_device()
return value
AMD IOMMU fixes:
- Fix lockdep splat for invalid wait context
- Add feature bit check before enabling PPR
- Make workqueue name fit into buffer
- Fix memory leak in sysfs code"
* tag 'iommu-fixes-v6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix Invalid wait context issue
iommu/amd: Check EFR[EPHSup] bit before enabling PPR
iommu/amd: Fix workqueue name
iommu: Return right value in iommu_sva_bind_device()
iommu/dma: Fix domain init
iommu/amd: Fix sysfs leak in iommu init
vmwgfx:
- filter modes greater than available graphics memory
- fix 3D vs STDU enable
- remove STDU logic from mode valid
- logging fix
- memcmp pointers fix
- remove unused struct
- screen target lifetime fix
komeda:
- unused struct removal"
* tag 'drm-fixes-2024-06-07' of https://gitlab.freedesktop.org/drm/kernel:
drm/vmwgfx: Don't memcmp equivalent pointers
drm/vmwgfx: remove unused struct 'vmw_stdu_dma'
drm/vmwgfx: Don't destroy Screen Target when CRTC is enabled but inactive
drm/vmwgfx: Standardize use of kibibytes when logging
drm/vmwgfx: Remove STDU logic from generic mode_valid function
drm/vmwgfx: 3D disabled should not effect STDU memory limits
drm/vmwgfx: Filter modes which exceed graphics memory
drm/amdgpu/pptable: Fix UBSAN array-index-out-of-bounds
drm/amd: Fix shutdown (again) on some SMU v13.0.4/11 platforms
drm/xe/pf: Update the LMTT when freeing VF GT config
drm/panel: sitronix-st7789v: Add check for of_drm_get_panel_orientation
drm/komeda: remove unused struct 'gamma_curve_segment'
Noralf Trønnes [Tue, 4 Jun 2024 13:20:32 +0000 (15:20 +0200)]
drm/tiny: panel-mipi-dbi: Support the pixel format property
Add support for these pixel format property values:
- r5g6b5, RGB565
- b6x2g6x2r6x2, BGR666
BGR666 is presented to userspace as RGB888. The 2 LSB in each color
are discarded by the controller. The pixel is sent on the wire using
8 bits per word (little endian) so the controller sees it as BGR.
RGB565 is the default if the property is not present.
Noralf Trønnes [Tue, 4 Jun 2024 13:20:31 +0000 (15:20 +0200)]
drm/mipi-dbi: Add support for DRM_FORMAT_RGB888
DRM_FORMAT_RGB888 is 24 bits per pixel and it would be natural to send it
on the SPI bus using a 24 bits per word transfer. The problem with this
is that not all SPI controllers support 24 bpw.
Since DRM_FORMAT_RGB888 is stored in memory as little endian and the SPI
bus is big endian we use 8 bpw to always get the same pixel format on the
bus: b8g8r8.
The MIPI DCS specification lists the standard commands that can be sent
over the MIPI DBI interface. The set_address_mode (36h) command has one
bit in the parameter that controls RGB/BGR order. This means that the
controller can be configured to receive the pixel as BGR.
RGB888 is rarely supported on these controllers but RGB666 is very common.
All datasheets I have seen do at least support the pixel format option
where each color is sent as one byte and the 6 MSB's are used.
All this put together means that we can send each pixel as b8g8r8 and an
RGB666 capable controller sees this as b6x2g6x2r6x2.
Noralf Trønnes [Tue, 4 Jun 2024 13:20:30 +0000 (15:20 +0200)]
drm/mipi-dbi: Make bits per word configurable for pixel transfers
MIPI DCS write/set commands have 8 bit parameters except for the
write_memory commands where it depends on the pixel format.
drm_mipi_dbi does currently only support RGB565 which is 16-bit and it
has to make sure that the pixels enters the SPI bus in big endian format
since the MIPI DBI spec doesn't have support for little endian.
drm_mipi_dbi is optimized for DBI interface option 3 which means that the
16-bit bytes are swapped by the upper layer if the SPI bus does not
support 16 bits per word, signified by the swap_bytes member.
In order to support both 16-bit and 24-bit pixel transfers we need a way
to tell the DBI command layer the format of the buffer. Add a
write_memory_bpw member that the upper layer can use to tell how many
bits per word to use for the SPI transfer.
mipi_dbi_machine_little_endian() should really have been called
mipi_dbi_framebuffer_little_endian() because that's the function it
performs. When I added support for these SPI displays I thought that the
framebuffers on big endian machines were also big endian, but I have
later learned that this is not the case. There's a bit in the fourcc code
that controls this: DRM_FORMAT_BIG_ENDIAN.
Just remove the function to avoid confusion. We can add big endian support
later should the need arise and we have hardware to test on.
Instead of just amending the docs, expand it to explain the endianness
handling.
Noralf Trønnes [Tue, 4 Jun 2024 13:20:28 +0000 (15:20 +0200)]
dt-bindings: display: panel: mipi-dbi-spi: Add a pixel format property
The MIPI DBI 2.0 specification (2005) lists only two pixel formats for
the Type C Interface (SPI) and that is 3-bits/pixel RGB111 with
2 options for bit layout.
For Type A and B (parallel) the following formats are listed: RGB332,
RGB444, RGB565, RGB666 and RGB888 (some have 2 options for the bit layout).
Many MIPI DBI compatible controllers support all interface types on the
same chip and often the manufacturers have chosen to provide support for
the Type A/B interface pixel formats also on the Type C interface.
Some chips provide many pixel formats with optional bit layouts over SPI,
but the most common by far are RGB565 and RGB666. So even if the
specification doesn't list these formats for the Type C interface, the
industry has chosen to include them.
The MIPI DCS specification lists the standard commands that can be sent
over the MIPI DBI interface. The set_address_mode (36h) command has one
bit in the parameter that controls RGB/BGR order:
This bit controls the RGB data latching order transferred from the
peripheral’s frame memory to the display device.
This means that each supported RGB format also has a BGR variant.
Based on this rationale document the following pixel formats describing
the bit layout going over the wire:
- RGB111 (option 1): x2r1g1b1r1g1b1 (2 pixels per byte)
- BGR111 (option 1): x2b1g1r1b1g1r1 (2 pixels per byte)
- RGB111 (option 2): x1r1g1b1x1r1g1b1 (2 pixels per byte)
- BGR111 (option 2): x1b1g1r1x1b1g1r1 (2 pixels per byte)
- RGB565: r5g6b5 (2 bytes)
- BGR565: b5g6r5 (2 bytes)
- RGB666: r6x2g6x2b6x2 (3 bytes)
- BGR666: b6x2g6x2r6x2 (3 bytes)
(x: don't care)
Johan Hovold [Tue, 7 May 2024 14:48:18 +0000 (16:48 +0200)]
HID: i2c-hid: elan: fix reset suspend current leakage
The Elan eKTH5015M touch controller found on the Lenovo ThinkPad X13s
shares the VCC33 supply with other peripherals that may remain powered
during suspend (e.g. when enabled as wakeup sources).
The reset line is also wired so that it can be left deasserted when the
supply is off.
This is important as it avoids holding the controller in reset for
extended periods of time when it remains powered, which can lead to
increased power consumption, and also avoids leaking current through the
X13s reset circuitry during suspend (and after driver unbind).
Use the new 'no-reset-on-power-off' devicetree property to determine
when reset needs to be asserted on power down.
Notably this also avoids wasting power on machine variants without a
touchscreen for which the driver would otherwise exit probe with reset
asserted.
Fixes: bd3cba00dcc6 ("HID: i2c-hid: elan: Add support for Elan eKTH6915 i2c-hid touchscreens") Cc: <stable@vger.kernel.org> # 6.0 Cc: Douglas Anderson <dianders@chromium.org> Tested-by: Steev Klimaszewski <steev@kali.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20240507144821.12275-5-johan+linaro@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
When the power supply is shared with other peripherals the reset line
can be wired in such a way that it can remain deasserted regardless of
whether the supply is on or not.
This is important as it can be used to avoid holding the controller in
reset for extended periods of time when it remains powered, something
which can lead to increased power consumption. Leaving reset deasserted
also avoids leaking current through the reset circuitry pull-up
resistors.
Add a new 'no-reset-on-power-off' devicetree property which can be used
by the OS to determine when reset needs to be asserted on power down.
Note that this property can also be used when the supply cannot be
turned off by the OS at all.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20240507144821.12275-4-johan+linaro@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Johan Hovold [Tue, 7 May 2024 14:48:16 +0000 (16:48 +0200)]
dt-bindings: HID: i2c-hid: elan: add Elan eKTH5015M
Add a compatible string for the Elan eKTH5015M touch controller.
Judging from the current binding and commit bd3cba00dcc6 ("HID: i2c-hid:
elan: Add support for Elan eKTH6915 i2c-hid touchscreens"), eKTH5015M
appears to be compatible with eKTH6915. Notably the power-on sequence is
the same.
While at it, drop a redundant label from the example.
The Ilitek ILI2901 touch screen controller was apparently incorrectly
added to the Elan eKTH6915 schema simply because it also has a reset
gpio and is currently managed by the Elan driver in Linux.
The two controllers are not related even if an unfortunate wording in
the commit message adding the Ilitek compatible made it sound like they
were.
Add a dedicated schema for the ILI2901 which does not specify the I2C
address (which is likely 0x41 rather than 0x10 as for other Ilitek touch
controllers) to avoid cluttering the Elan schema with unrelated devices
and to make it easier to find the correct schema when adding further
Ilitek controllers.
Fixes: d74ac6f60a7e ("dt-bindings: HID: i2c-hid: elan: Introduce Ilitek ili2901") Cc: Zhengqiao Xia <xiazhengqiao@huaqin.corp-partner.google.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240507144821.12275-2-johan+linaro@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Aseda Aboagye [Tue, 4 Jun 2024 23:16:32 +0000 (23:16 +0000)]
input: Add support for "Do Not Disturb"
HUTRR94 added support for a new usage titled "System Do Not Disturb"
which toggles a system-wide Do Not Disturb setting. This commit simply
adds a new event code for the usage.
Aseda Aboagye [Tue, 4 Jun 2024 23:10:47 +0000 (23:10 +0000)]
input: Add event code for accessibility key
HUTRR116 added support for a new usage titled "System Accessibility
Binding" which toggles a system-wide bound accessibility UI or command.
This commit simply adds a new event code for the usage.
Jeff Johnson [Fri, 7 Jun 2024 03:23:50 +0000 (20:23 -0700)]
gpio: add missing MODULE_DESCRIPTION() macros
On x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-gw-pld.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-mc33880.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-pcf857x.o
Add the missing invocations of the MODULE_DESCRIPTION() macro,
including the one missing in gpio-pl061.c, which is not built for x86.
David Howells [Fri, 31 May 2024 14:53:42 +0000 (15:53 +0100)]
cifs: Don't advance the I/O iterator before terminating subrequest
There's now no need to make sure subreq->io_iter is advanced to match
subreq->transferred before calling one of the netfs subrequest termination
functions as the check has been removed netfslib and the iterator is reset
prior to retrying a subreq.
Fixes: 3ee1a1fc3981 ("cifs: Cut over to using netfslib") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
cc: linux-mm@kvack.org Signed-off-by: Steve French <stfrench@microsoft.com>
Masahiro Yamada [Thu, 6 Jun 2024 18:36:12 +0000 (03:36 +0900)]
modpost: do not warn about missing MODULE_DESCRIPTION() for vmlinux.o
Building with W=1 incorrectly emits the following warning:
WARNING: modpost: missing MODULE_DESCRIPTION() in vmlinux.o
This check should apply only to modules.
Fixes: 1fffe7a34c89 ("script: modpost: emit a warning when the description is missing") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Vincenzo Palazzo <vincenzopalazzodev@gmail.com>
Richard Acayan [Wed, 5 Jun 2024 17:58:09 +0000 (13:58 -0400)]
kbuild: explicitly run mksysmap as sed script from link-vmlinux.sh
In commit b18b047002b7 ("kbuild: change scripts/mksysmap into sed
script"), the mksysmap script was transformed into a sed script,
made directly executable with "#!/bin/sed -f". Apparently, the path to
sed is different on NixOS.
The shebang can't use the env command, otherwise the "sed -f" command
would be treated as a single argument. This can be solved with the -S
flag, but that is a GNU extension. Explicitly use sed instead of relying
on the executable shebang to fix NixOS builds without breaking build
environments using Busybox.
Fixes: b18b047002b7 ("kbuild: change scripts/mksysmap into sed script") Reported-by: Kent Overstreet <kent.overstreet@linux.dev> Signed-off-by: Richard Acayan <mailingradian@gmail.com> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Tested-by: Dmitry Safonov <0x7f454c46@gmail.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Linus Torvalds [Thu, 6 Jun 2024 21:40:51 +0000 (14:40 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The core change is to detect unusually large number of VPD pages
(caused by device manufacturers having an endiannes issue) and reject
them rather than trying to parse a huge non-existent array.
The remaining fixes are in drivers the most user visible of which is
the ALUA state transition recognition (leads to intermittent I/O
errors in some situations otherwise)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: mcq: Fix error output and clean up ufshcd_mcq_abort()
scsi: core: Handle devices which return an unusually large VPD page count
scsi: mpt3sas: Add missing kerneldoc parameter descriptions
scsi: qedf: Set qed_slowpath_params to zero before use
scsi: qedf: Wait for stag work during unload
scsi: qedf: Don't process stag work during unload and recovery
scsi: sr: Fix unintentional arithmetic wraparound
scsi: core: alua: I/O errors for ALUA state transitions
scsi: mpi3mr: Use proper format specifier in mpi3mr_sas_port_add()
Linus Torvalds [Thu, 6 Jun 2024 21:28:11 +0000 (14:28 -0700)]
Merge tag 'pci-v6.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Revert lockdep checking on locking that protects device resets from
user-space config accesses; it exposed issues for which fixes are in
the works but are too risky for this cycle (Dan Williams)
* tag 'pci-v6.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Revert the cfg_access_lock lockdep mechanism
[CAUSE]
Commit 09e6cef19c9f ("btrfs: refactor alloc_extent_buffer() to
allocate-then-attach method") changes the sequence when allocating a new
extent buffer.
Previously we always called grab_extent_buffer() under
mapping->i_private_lock, to ensure the safety on modification on
folio::private (which is a pointer to extent buffer for regular
sectorsize).
This can lead to the following race:
Thread A is trying to allocate an extent buffer at bytenr X, with 4
4K pages, meanwhile thread B is trying to release the page at X + 4K
(the second page of the extent buffer at X).
Thread A | Thread B
-----------------------------------+-------------------------------------
| btree_release_folio()
| | This is for the page at X + 4K,
| | Not page X.
| |
alloc_extent_buffer() | |- release_extent_buffer()
|- filemap_add_folio() for the | | |- atomic_dec_and_test(eb->refs)
| page at bytenr X (the first | | |
| page). | | |
| Which returned -EEXIST. | | |
| | | |
|- filemap_lock_folio() | | |
| Returned the first page locked. | | |
| | | |
|- grab_extent_buffer() | | |
| |- atomic_inc_not_zero() | | |
| | Returned false | | |
| |- folio_detach_private() | | |- folio_detach_private() for X
| |- folio_test_private() | | |- folio_test_private()
| Returned true | | | Returned true
|- folio_put() | |- folio_put()
Now there are two puts on the same folio at folio X, leading to refcount
underflow of the folio X, and eventually causing the BUG_ON() on the
page->mapping.
The condition is not that easy to hit:
- The release must be triggered for the middle page of an eb
If the release is on the same first page of an eb, page lock would kick
in and prevent the race.
- folio_detach_private() has a very small race window
It's only between folio_test_private() and folio_clear_private().
That's exactly when mapping->i_private_lock is used to prevent such race,
and commit 09e6cef19c9f ("btrfs: refactor alloc_extent_buffer() to
allocate-then-attach method") screwed that up.
At that time, I thought the page lock would kick in as
filemap_release_folio() also requires the page to be locked, but forgot
the filemap_release_folio() only locks one page, not all pages of an
extent buffer.
[FIX]
Move all the code requiring i_private_lock into
attach_eb_folio_to_filemap(), so that everything is done with proper
lock protection.
Furthermore to prevent future problems, add an extra
lockdep_assert_locked() to ensure we're holding the proper lock.
To reproducer that is able to hit the race (takes a few minutes with
instrumented code inserting delays to alloc_extent_buffer()):
projects / users / dwmw2 / linux.git / log