Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org Fixes: f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready...") Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This was discovered developing qemu fwnmi sreset support. This
off-by-one bug means the last 16 bytes of the rtas area can not
be used for a 16 byte save area.
It's not a serious bug, and QEMU implementation has to retain a
workaround for old kernels, but it's good to tighten it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Mahesh Salgaonkar <mahesh@linux.ibm.com> Link: https://lore.kernel.org/r/20200508043408.886394-7-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
pseries fwnmi machine check code pops the soft-irq checks in rtas_call
(after the next patch to remove rtas_token from this call path).
Rather than play whack a mole with these and forever having fragile
code, it seems better to have the early machine check handler perform
the same kind of reconcile as the other NMI interrupts.
The architecture allows for machine check exceptions to cause idle
wakeups which resume at the 0x200 address which has to return via
the idle wakeup code, but the early machine check handler is run
first.
The case of a no state-loss sleep is broken because the early
handler uses non-volatile register r1 , which is needed for the wakeup
protocol, but it is not restored.
Fix this by loading r1 from the MCE exception frame before returning
to the idle wakeup code. Also update the comment which has become
stale since the idle rewrite in C.
This crash was found and fix confirmed with a machine check injection
test in qemu powernv model (which is not upstream in qemu yet).
Fixes: 10d91611f426d ("powerpc/64s: Reimplement book3s idle code in C") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200508043408.886394-2-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the situation where the GPIO controller is not
used as an interrupt controller as well.
Previously, the driver would silently fail to register even the
GPIO's. With this change, the driver will only register as an
interrupt controller if a parent interrupt is provided.
We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.
We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.
Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.
So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.
We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Remi Pommarel <repk@triplefau.lt> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When doing training, the DL framework (e.g. tensorflow) performs hundreds
of thousands of memory allocations and mappings. In case the driver needs
to perform hard-reset during training, the driver kills the application and
unmaps all those memory allocations. Unfortunately, because of that large
amount of mappings, the driver isn't able to do that in the current timeout
(5 seconds). Therefore, increase the timeout significantly to 30 seconds
to avoid situation where the driver resets the device with active mappings,
which sometime can cause a kernel bug.
BTW, it doesn't mean we will spend all the 30 seconds because the reset
thread checks every one second if the unmap operation is done.
Kai-Heng Feng reported that it takes a long time (> 1 s) to resume
Thunderbolt-connected devices from both runtime suspend and system sleep
(s2idle).
This was because some Downstream Ports that support > 5 GT/s do not also
support Data Link Layer Link Active reporting. Per PCIe r5.0 sec 6.6.1:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Sec 7.5.3.6 requires such Ports to support DLL Link Active reporting, but
at least the Intel JHL6240 Thunderbolt 3 Bridge [8086:15c0] and the Intel
JHL7540 Thunderbolt 3 Bridge [8086:15ea] do not.
Previously we tried to wait for Link training to complete, but since there
was no DLL Link Active reporting, all we could do was wait the worst-case
1000 ms, then another 100 ms.
Instead of using the supported speeds to determine whether to wait for Link
training, check whether the port supports DLL Link Active reporting. The
Ports in question do not, so we'll wait only the 100 ms required for Ports
that support Link speeds <= 5 GT/s.
This of course assumes these Ports always train the Link within 100 ms even
if they are operating at > 5 GT/s, which is not required by the spec.
The Trust Panora Graphic Tablet has two interfaces. Interface zero reports pen
movement, pen pressure and pen buttons. Interface one reports tablet buttons
and tablet scroll. Both use the mouse protocol.
Without these quirks, libinput gets confused about what device it talks to.
For USB sound devices using implicit feedback the endpoint used for
this feedback should be able to be opened twice, once for required
feedback and second time for audio data. This way these devices can be
put in duplex audio mode. Since this only works if the settings of the
endpoint don't change a check is included for this.
This fixes bug 207023 ("MOTU M2 regression on duplex audio") and
should also fix bug 103751 ("M-Audio Fast Track Ultra usb audio device
will not operate full-duplex")
Before to start the scan request, the firmware signals (with a null
frame) to the AP it won't be able to receive data. This frame can be
long to send: up to 512TU. The current calculus of the scan timeout does
not take into account this delay.
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
ie. if MSR_VSX is set then both of MSR_FP and MSR_VEC are also set.
Dumping tsk->thread.regs->msr we see that it's: 0x1db60000
Which is not a normal looking MSR, in fact the only valid bit is
MSR_VSX, all the other bits are reserved in the current definition of
the MSR.
We can see from the oops that it was swapper/0 that we were switching
from when we hit the warning, ie. init_task. So its thread.regs points
to the base (high addresses) in init_stack.
Dumping the content of init_task->thread.regs, with the members of
pt_regs annotated (the 16 bytes larger version), we see:
This looks suspiciously like stack frames, not a pt_regs. If we look
closely we can see return addresses from the stack trace above, c000000002004820 (start_kernel) and c00000000000c49c (start_here_common).
init_task->thread.regs is setup at build time in processor.h:
The early boot code where we setup the initial stack is:
LOAD_REG_ADDR(r3,init_thread_union)
/* set up a stack pointer */
LOAD_REG_IMMEDIATE(r1,THREAD_SIZE)
add r1,r3,r1
li r0,0
stdu r0,-STACK_FRAME_OVERHEAD(r1)
Which creates a stack frame of size 112 bytes (STACK_FRAME_OVERHEAD).
Which is far too small to contain a pt_regs.
So the result is init_task->thread.regs is pointing at some stack
frames on the init stack, not at a pt_regs.
We have gotten away with this for so long because with pt_regs at its
current size the MSR happens to point into the first frame, at a
location that is not written to by the early asm. With the 16 byte
expansion the MSR falls into the second frame, which is used by the
compiler, and collides with a saved register that tends to be
non-zero.
As far as I can see this has been wrong since the original merge of
64-bit ppc support, back in 2002.
Conceptually swapper should have no regs, it never entered from
userspace, and in fact that's what we do on 32-bit. It's also
presumably what the "bogus" comment is referring to.
So I think the right fix is to just not-initialise regs at all. I'm
slightly worried this will break some code that isn't prepared for a
NULL regs, but we'll have to see.
Remove the comment in head_64.S which refers to us setting up the
regs (even though we never did), and is otherwise not really accurate
any more.
It's uncertain where the "vreg_s8a_l3a_input" comes from, but the supply
for VDD_L3_L11 on PM8994 should be VREG_S3A_1P3, so correct this - and
drop the vreg_s8a_l3a_input.
Fix to return negative error code from some error handling
cases instead of 0, as done elsewhere in this function.
Fixes: 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Roger Quadros <rogerq@ti.com> Link: https://lore.kernel.org/r/20200507054109.110849-1-weiyongjun1@huawei.com Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Building a kernel with clang sometimes fails with an objtool error in dlm:
fs/dlm/lock.o: warning: objtool: revert_lock_pc()+0xbd: can't find jump dest instruction at .text+0xd7fc
The problem is that BUG() never returns and the compiler knows
that anything after it is unreachable, however the panic still
emits some code that does not get fully eliminated.
Having both BUG() and panic() is really pointless as the BUG()
kills the current process and the subsequent panic() never hits.
In most cases, we probably don't really want either and should
replace the DLM_ASSERT() statements with WARN_ON(), as has
been done for some of them.
Remove the BUG() here so the user at least sees the panic message
and we can reliably build randconfig kernels.
Fixes: e7fd41792fc0 ("[DLM] The core of the DLM for GFS2/CLVM") Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: clang-built-linux@googlegroups.com Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
7C retail devices using MSA based boot will result in a fuse combination
which will prevent accesses to MSS PERPH register space where the mpss
clocks and halt-nav reside. So drop all accesses to the MPSS PERPH
register space. Issuing HALT NAV request and turning on the mss clocks
as part of SSR will no longer be required since the modem firmware will
have the necessary fixes to ensure that there are no pending NAV DMA
transactions.
Tested-by: Evan Green <evgreen@chromium.org> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20200415145110.20624-3-sibis@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This uses devres and attaches new_map to the pinctrl driver.
This cause a leak since new_map is not released when the probed
driver is removed. Fix it by using kcalloc to allocate new_map
and free it in `rockchip_dt_free_map`
There are 2 issues here:
- if one of the 'of_parse_phandle' fails, calling 'mop500_of_node_put()'
is a no-op because the 'mop500_dai_links' structure has not been
initialized yet, so the referenced are not decremented
- The reference stored in 'mop500_dai_links[i].codecs' is refcounted
only once in the probe and must be decremented only once.
Fixes: 39013bd60e79 ("ASoC: Ux500: Dispose of device nodes correctly") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20200512100705.246349-1-christophe.jaillet@wanadoo.fr Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SSI BUSIF buffer is possible to overflow or underflow, especially in a
hypervisor environment. If there is no interrupt support, it will eventually
lead to errors in pcm data.
This patch adds overflow and underflow interrupt support for SSI BUSIF buffer.
Reported-by: Chen Li <licheng0822@thundersoft.com> Signed-off-by: Yongbo Zhang <giraffesnn123@gmail.com> Tested-by: Chen Li <licheng0822@thundersoft.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20200512093003.28332-1-giraffesnn123@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During zstd compression, ZSTD_endStream() may return non-zero value
because distination buffer is full, but there is still compressed data
remained in intermediate buffer, it means that zstd algorithm can not
save at last one block space, let's just writeback raw data instead of
compressed one, this can fix data corruption when decompressing
incomplete stored compression data.
In error path of f2fs_read_multi_pages(), it should let last referrer
release decompress io context memory, otherwise, other referrer will
cause use-after-free issue.
Fixes: 4c8ff7095bef ("f2fs: support data compression") Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We use tcm_loop with tape emulations running on tcmu.
In case application reads a short tape block with a longer READ, or a long
tape block with a short READ, according to SCC spec data has to be
tranferred _and_ sensebytes with ILI set and information field containing
the residual count. Similar problem also exists when using fixed block
size in READ.
Up to now tcm_loop is not prepared to handle sensebytes if input data is
provided, as in tcm_loop_queue_data_in() it only sets SAM_STAT_GOOD and, if
necessary, the residual count.
To fix the bug, the same handling for sensebytes as present in
tcm_loop_queue_status() must be done in tcm_loop_queue_data_in() also.
After adding this handling, the two function now are nearly identical, so I
created a single function with two wrappers.
While preparing the driver for upstream this detail was missed.
If not asserted during the initialization process, devices connected on
the bus will not be made aware of the internal reset happening. This,
potentially resulting in unexpected behavior.
In the probe function, in case of error, resources allocated in
'lp8788_setup_adc_channel()' must be released.
This can be achieved easily by using the devm_ variant of
'iio_channel_get()'.
This has the extra benefit to simplify the remove function and to axe the
'lp8788_release_adc_channel()' function which is now useless.
Fixes: 98a276649358 ("power_supply: Add new lp8788 charger driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Although the value of FDF is used just for outgoing stream, the assignment
to union member is done for both directions of stream. At present this
causes no issue because the value of same position is reassigned later for
opposite stream. However, it's better to add if statement.
Fixes: d3d10a4a1b19 ("ALSA: firewire-lib: use union for directional parameters") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20200508043635.349339-2-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The issue happens because no real ISP reset is executed. The
qla2x00_abort_isp(scsi_qla_host_t *vha) function expects that
vha->flags.online will be not zero for ISP reset procedure. This patch
sets vha->flags.online to 1 before calling ->abort_isp() for starting the
ISP reset.
7d715a6c1ae5 ("PCI: add PCI Express ASPM support") added the ability for
Linux to enable ASPM, but for some undocumented reason, it didn't enable
ASPM on links where the downstream component is a PCIe-to-PCI/PCI-X Bridge.
Remove this exclusion so we can enable ASPM on these links.
The Dell OptiPlex 7080 mentioned in the bugzilla has a TI XIO2001
PCIe-to-PCI Bridge. Enabling ASPM on the link leading to it allows the
Intel SoC to enter deeper Package C-states, which is a significant power
savings.
The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between
a CPU address (which is determined by the window number 'x') and a
programmed PCI address - Thus allowing the controller to translate CPU
accesses into PCI accesses.
However the existing code incorrectly writes the CPU address - lets fix
this by writing the PCI address instead.
For memory transactions, existing DT users describe a 1:1 identity mapping
and thus this change should have no effect. However the same isn't true for
I/O.
Link: https://lore.kernel.org/r/20191004132941.6660-1-andrew.murray@arm.com Fixes: c25da4778803 ("PCI: rcar: Add Renesas R-Car PCIe driver") Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com> Signed-off-by: Andrew Murray <andrew.murray@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If platform bus driver registration is failed then, accessing
platform bus spin lock (&drv->driver.bus->p->klist_drivers.k_lock)
in __platform_driver_probe() without verifying the return value
__platform_driver_register() can lead to NULL pointer exception.
So check the return value before attempting the spin lock.
One such example is below:
For a custom usecase, I have intentionally failed the platform bus
registration and I expected all the platform device/driver
registrations to fail gracefully. But I came across this panic
issue.
The IRQ log output is supposed to appear on a single line. However,
commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.
Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.
Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_OF is disabled, gcc-9 produces a warning about the
wfx_sdio_of_match[] array having a declaration without a dimension:
drivers/staging/wfx/bus_sdio.c:159:34: error: array 'wfx_sdio_of_match' assumed to have one element [-Werror]
159 | static const struct of_device_id wfx_sdio_of_match[];
| ^~~~~~~~~~~~~~~~~
Move the proper declaration up and out of the #ifdef instead.
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Older compilers like gcc-4.8 don't see that the variable is
initialized when it is used:
In file included from include/linux/compiler_types.h:68:0,
from <command-line>:0:
drivers/hid/intel-ish-hid/ishtp-fw-loader.c: In function 'load_fw_from_host':
include/linux/compiler-gcc.h:75:45: warning: 'fw_info.ldr_capability.max_dma_buf_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
#define __UNIQUE_ID(prefix) __PASTE(__PASTE(__UNIQUE_ID_, prefix), __COUNTER__)
^
drivers/hid/intel-ish-hid/ishtp-fw-loader.c:770:22: note: 'fw_info.ldr_capability.max_dma_buf_size' was declared here
struct shim_fw_info fw_info;
^
Make sure to initialize it before returning an error from ish_query_loader_prop().
Fixes the following warnings for both g5 and g6 SoCs:
arch/arm/boot/dts/aspeed-g5.dtsi:376.19-381.8: Warning
(unit_address_vs_reg): /ahb/apb/lpc@1e789000/lpc-bmc@0/kcs1@0: node
has a unit name, but no reg property
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to ASPEED, FTTMR010 is not intended to be used in the AST2600.
The arch timer should be used, but Linux doesn't enable high-res timers
without being assured that the arch timer is always on, so set that
property in the devicetree.
The FTTMR010 device is described by set to disabled.
This fixes highres timer support for AST2600.
Fixes: 2ca5646b5c2f ("ARM: dts: aspeed: Add AST2600 and EVB") Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error handling flow seems incorrect, there is no reason to try and
add debugfs support if the device registration did not
succeed. Return on error.
When calling regmap_update_bits(), since map->reg_update_bits is NULL,
_regmap_read() is entered with the following logic:
if (!map->cache_bypass) {
ret = regcache_read(map, reg, val);
if (ret == 0)
return 0;
}
if (map->cache_only)
return -EBUSY;
regcache_read() hits -EINVAL because MAX98373_R2000_SW_RESET is volatile,
as map->cache_only is set by codec suspend, thus -EBUSY is returned.
Fix by moving max98373_reset() after cache_only set to false in max98373_resume().
Not all u-boot versions initialize the HHI_GP_PLL_CNTL[2-5] registers.
In that case all HHI_GPLL_PLL_CNTL[1-5] registers are 0x0 and when
booting Linux the PLL fails to lock.
The initialization sequence from u-boot is:
- put the PLL into reset
- write 0x59C88000 to HHI_GP_PLL_CNTL2
- write 0xCA463823 to HHI_GP_PLL_CNTL3
- write 0x0286A027 to HHI_GP_PLL_CNTL4
- write 0x00003000 to HHI_GP_PLL_CNTL5
- set M, N, OD and the enable bit
- take the PLL out of reset
- check if it has locked
- disable the PLL
In Linux we already initialize M, N, OD, the enable and the reset bits.
Also the HHI_GP_PLL_CNTL[2-5] registers with these magic values (the
exact meaning is unknown) so the PLL can lock when the vendor u-boot did
not initialize these registers yet.
Fixes: b882964b376f21 ("clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20200501215717.735393-1-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
At the first time update_mute_led() gets called, if channels are already
muted, the temp value equals to led_value as 0, skipping the following
LED setting.
So set led_value to -1 as an uninitialized state, to update the correct
LED status at first time usage.
Fixes: 5d43001ae436 ("ASoC: SOF: acpi led support for switch controls") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Acked-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20200430091139.7003-1-kai.heng.feng@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the leds subnode names to match (^led-[0-9a-f]$|led)
It fixes:
meson-g12b-a311d-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-s922x-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-odroid-n2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nanopi-k2.dt.yaml: leds: 'stat' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nexbox-a95x.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-odroidc2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-pro.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-meta.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-telos.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-hub.dt.yaml: leds: 'system' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-play2.dt.yaml: leds: 'ethernet', 'system', 'wifi' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905x-libretech-cc.dt.yaml: leds: 'blue', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905d-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-rbox-pro.dt.yaml: leds: 'blue', 'red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-s912-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-sei610.dt.yaml: leds: 'bluetooth' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-khadas-vim3l.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
If one of the two is a loadable module, the combined driver must
not be built-in:
aarch64-linux-ld: sound/soc/codecs/rt5682.o: in function `rt5682_sdw_hw_free':
rt5682.c:(.text+0xb34): undefined reference to `sdw_stream_remove_slave'
aarch64-linux-ld: sound/soc/codecs/rt5682.o: in function `rt5682_sdw_hw_params':
rt5682.c:(.text+0xe78): undefined reference to `sdw_stream_add_slave'
In particular, the soundwire driver must not be built-in if
CONFIG_I2C=m.
On error the function ti_bandgap_get_sensor_data() returns the error
code in ERR_PTR() but we only checked if the return value is NULL or
not. And, so we can dereference an error code inside ERR_PTR.
While at it, convert a check to IS_ERR_OR_NULL.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200424161944.6044-1-sudipm.mukherjee@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Old versions of gcc (tested on gcc-4.8) produce a warning for
correct code:
sound/soc/soc-compress.c: In function 'soc_compr_open':
sound/soc/soc-compress.c:75:28: error: 'component' is used uninitialized in this function [-Werror=uninitialized]
struct snd_soc_component *component, *save = NULL;
Change the for_each_rtd_components() macro to ensure 'component'
gets initialized to a value the compiler does not complain about.
Some of the chips supported by the pca953x driver need the most
significant bit in the address word set to automatically increment the
address pointer on subsequent reads and writes (example: PCA9505). With
this bit unset the same register is read multiple times on a multi-byte
read sequence. Other chips must not have this bit set and autoincrement
always (example: PCA9555).
Up to now this AI bit was interpreted to be part of the address, which
resulted in inconsistent regmap caching when a register was written with
AI set and then read without it. This happened for the PCA9505 in
pca953x_gpio_set_multiple() where pca953x_read_regs() bulk read from the
cache for registers 0x8-0xc and then wrote to registers 0x88-0x8c. (Side
note: reading 5 values from offset 0x8 yiels OP0 5 times because AI must
be set to get OP0-OP4, which is another bug that is resolved here as a
by-product.) The same problem happens when calls to gpio_set_value() and
gpio_set_array_value() were mixed.
With this patch the AI bit is always set for chips that support it. This
works as there are no code locations that make use of the behaviour with
AI unset (for the chips that support it).
Note that the call to pca953x_setup_gpio() had to be done a bit earlier
to make the NBANK macro work.
The history of this bug is a bit complicated. Commit b32cecb46bdc
("gpio: pca953x: Extract the register address mangling to single
function") changed which chips and functions are affected. Commit 3b00691cc46a ("gpio: pca953x: hack to fix 24 bit gpio expanders") used
some duct tape to make the driver at least appear to work. Commit 49427232764d ("gpio: pca953x: Perform basic regmap conversion")
introduced the caching. Commit b4818afeacbd ("gpio: pca953x: Add
set_multiple to allow multiple bits to be set in one write.") introduced
the .set_multiple() callback which didn't work for chips that need the
AI bit which was fixed later for some chips in 8958262af3fb ("gpio:
pca953x: Repair multi-byte IO address increment on PCA9575"). So I'm
sorry, I don't know which commit I should pick for a Fixes: line.
Tested-by: Marcel Gudert <m.gudert@eckelmann.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_POST and
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_PRE are active low. This means:
- asserting them requires setting the register value to 0
- de-asserting them requires setting the register value to 1
Set the register value accordingly for these two reset lines by setting
the inverted the register value compared to all other reset lines.
Use hdmi_pll_lvds_out as parent of the vid_pll_in_sel clock. It's not
easy to see that the vendor kernel does the same, but it actually does.
meson_clk_pll_ops in mainline still cannot fully recalculate all rates
from the HDMI PLL registers because some register bits (at the time of
writing it's unknown which bits are used for this) double the HDMI PLL
output rate (compared to simply considering M, N and FRAC) for some (but
not all) PLL settings.
Update the vid_pll_in_sel parent so our clock calculation works for
simple clock settings like the CVBS output (where no rate doubling is
going on). The PLL ops need to be fixed later on for more complex clock
settings (all HDMI rates).
Fixes: 6cb57c678bb70 ("clk: meson: meson8b: add the read-only video clock trees") Suggested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20200417184127.1319871-2-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When creating a consumer/supplier relationship between two devices,
make sure the supplier node is actually active. Otherwise this will
create a link relationship that will never be fulfilled. This, in the
worst case scenario, will hang the system during boot.
Note that, in practice, the fact that a device-tree represented
consumer/supplier relationship isn't fulfilled will not prevent devices
from successfully probing.
Fixes: a3e1d1a7f5fc ("of: property: Add functional dependency link from DT bindings") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Upon adding a new device from a DT node, we scan its properties and its
children's properties in order to create a consumer/supplier
relationship between the device and the property provider.
That said, it's possible for some of the node's children to be disabled,
which will create links that'll never be fulfilled.
To get around this, use the for_each_available_child_of_node() function
instead of for_each_available_node() when iterating over the node's
children.
Fixes: d4387cd11741 ("of: property: Create device links for all child-supplier depencencies") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
It has been reported that trying to send small packets of data could
produce a "inconsistent notification" warning.
It seems that in some circumstances, the number of frame queued in the
driver could greatly increase and exceed UCHAR_MAX. So the field
"buffered" from struct sta_priv can overflow.
Just increase the size of "bueffered" to fix the problem.
qdio_establish() calls qdio_setup_thinint() via qdio_setup_irq().
If the subsequent qdio_establish_thinint() fails, we miss to put the
DSCI again. Thus the DSCI isn't available for re-use. Given enough of
such errors, we could end up with having only the shared DSCI available.
Merge qdio_setup_thinint() into qdio_establish_thinint(), and deal with
such an error internally.
For rolling back after an error, qdio_establish() calls qdio_shutdown().
If the error occurs early enough, then the qdio_irq's state still is
QDIO_IRQ_STATE_INACTIVE and qdio_shutdown() does nothing.
But at _any_ point where qdio_establish() bails out in this way,
qdio_setup_irq() will have already replaced the IRQ handler. This then
won't be restored after an early error, and the device can end up being
returned to the device driver with qdio's IRQ handler still installed.
Slightly reorder qdio_setup_irq() so we can be 100% sure that the IRQ
handler was replaced. Then fix the bug in qdio_establish() by calling a
helper that rolls back only the IRQ handler modification.
Also use the new helper in qdio_shutdown() to keep things in sync, and
slightly clean up the locking while doing so.
This makes minor semantical changes, but holding setup_mutex gives us
sufficient leeway to eg. pull qdio_shutdown_thinint() outside of the
ccwdev lock's scope.
The linked list entry from FIFO is peeked at
queue_pending_output_urbs() but the actual element pop-out is
performed outside the spinlock, and it's potentially racy.
Do delete the link at the right place inside the spinlock.
For computation of the the next frame size current value of fs/fps and
accumulated fractional parts of fs/fps are used, where values are stored
in Q16.16 format. This is quite natural for computing frame size for
asynchronous endpoints driven by explicit feedback, since in this case
fs/fps is a value provided by the feedback endpoint and it's already in
the Q format. If an error is accumulated over time, the device can
adjust fs/fps value to prevent buffer overruns/underruns.
But for synchronous endpoints the accuracy provided by these computations
is not enough. Due to accumulated error the driver periodically produces
frames with incorrect size (+/- 1 audio sample).
This patch fixes this issue by implementing a different algorithm for
frame size computation. It is based on accumulating of the remainders
from division fs/fps and it doesn't accumulate errors over time. This
new method is enabled for synchronous and adaptive playback endpoints.
gasket_sysfs_register_store() invokes get_mapping(), which returns a
reference of the specified gasket_sysfs_mapping object to "mapping" with
increased refcnt.
When gasket_sysfs_register_store() returns, local variable "mapping"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The reference counting issue happens in one exception handling path of
gasket_sysfs_register_store(). When gasket_dev is NULL, the function
forgets to decrease the refcnt increased by get_mapping(), causing a
refcnt leak.
Fix this issue by calling put_mapping() when gasket_dev is NULL.
gasket_sysfs_put_attr() invokes get_mapping(), which returns a reference
of the specified gasket_sysfs_mapping object to "mapping" with increased
refcnt.
When gasket_sysfs_put_attr() returns, local variable "mapping" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
gasket_sysfs_put_attr(). When mapping attribute is unknown, the function
forgets to decrease the refcnt increased by get_mapping(), causing a
refcnt leak.
Fix this issue by calling put_mapping() when put attribute fails due to
unknown attribute.
As far as the device is concerned the dma address is the physical
address. There is no need to convert it to a physical address,
especially not using dma-direct internals that are not available
to drivers and which will interact badly with IOMMUs. Last but not
least the commit introducing it claimed to just fix a type issue,
but actually changed behavior.
Fixes: 6e37ccf78a532 ("firmware: qcom_scm: Use proper types for dma mappings") Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20200414123136.441454-1-hch@lst.de Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 963545357202 ("fuse: reduce allocation size for splice_write")
changed size of bufs array, so BUG_ON which checks the index of the array
shold also be fixed.
In virtiofs (unlike in regular fuse) processing of async replies is
serialized. This can result in a deadlock in rare corner cases when
there's a circular dependency between the completion of two or more async
replies.
Such a deadlock can be reproduced with xfstests:generic/503 if TEST_DIR ==
SCRATCH_MNT (which is a misconfiguration):
- Process A is waiting for page lock in worker thread context and blocked
(virtio_fs_requests_done_work()).
- Process B is holding page lock and waiting for pending writes to
finish (fuse_wait_on_page_writeback()).
- Write requests are waiting in virtqueue and can't complete because
worker thread is blocked on page lock (process A).
Fix this by creating a unique work_struct for each async reply that can
block (O_DIRECT read).
The rza1l_swio_entries referred to the wrong array rza1h_swio_pins,
which was intended to be rza1l_swio_pins. So let's fix it.
This is detected by the following gcc warning:
drivers/pinctrl/pinctrl-rza1.c:401:35: warning: ‘rza1l_swio_pins’
defined but not used [-Wunused-const-variable=]
static const struct rza1_swio_pin rza1l_swio_pins[] = {
^~~~~~~~~~~~~~~
Fixes: 039bc58e73b77723 ("pinctrl: rza1: Add support for RZ/A1L") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Link: https://lore.kernel.org/r/20200417111604.19143-1-yanaijie@huawei.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'size_t' type behaves differently on 64-bit architectures, and causes
compiler a warning of the sort "format '%u' expects argument of type
'unsigned int', but argument 3 has type 'size_t {aka long unsigned int}'".
This change adds the correct specifier for the 'align' field.
Fixes: 4538c18568099 ("iio: buffer-dmaengine: Report buffer length requirements") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MFW may make a call to qed and then to qedf for protocol statistics
while the function is still probing. If this happens it's possible that
some members of the struct qedf_ctx may not be fully initialized which can
result in a NULL pointer dereference or general protection fault.
To prevent this, add a new flag call QEDF_PROBING and set it when the
__qedf_probe() function is active. Then in the qedf_get_protocol_tlv_data()
function we can check if the function is still probing and return
immediantely before any uninitialized structures can be touched.
Link: https://lore.kernel.org/r/20200416084314.18851-9-skashyap@marvell.com Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 3d2613c4289f
("GPIO: gpio-dwapb: Enable platform driver binding to MFD driver")
introduced a use of the platform driver but missed to add the following line
to it:
MODULE_ALIAS("platform:gpio-dwapb");
Add this to get driver loaded automatically if platform device is registered.
projects / users / dwmw2 / linux.git / log