As recently Smatch suggested, a couple of places in ASIHPI driver may
expand the array directly from the user-space value with speculation:
sound/pci/asihpi/hpimsginit.c:70 hpi_init_response() warn: potential spectre issue 'res_size' (local cap)
sound/pci/asihpi/hpioctl.c:189 asihpi_hpi_ioctl() warn: potential spectre issue 'adapters'
This patch puts array_index_nospec() for hardening against them.
As recently Smatch suggested, one place in OPL3 driver may expand the
array directly from the user-space value with speculation:
sound/drivers/opl3/opl3_synth.c:476 snd_opl3_set_voice() warn: potential spectre issue 'snd_opl3_regmap'
This patch puts array_index_nospec() for hardening against it.
When CONFIG_SND_DYNAMIC_MINORS isn't set, there are only limited
number of devices available, and HD-audio, especially with HDMI/DP
codec, will fail to create more than two devices.
The driver warns about the lack of such devices and skips the PCM
device creations, but the HDMI driver still tries to create the
corresponding JACK, SPDIF and ELD controls even for the non-existing
PCM substreams. This results in confusion on user-space, and even may
break the operation.
Similarly, Intel HDMI/DP codec builds the ELD notification from i915
graphics driver, and this may be broken if a notification is sent for
the non-existing PCM stream.
This patch adds the check of the existence of the assigned PCM
substream in the both scenarios above, and skips the further operation
if the PCM substream is not assigned.
syzbot is reporting crashes triggered by memory allocation fault injection
at tty_ldisc_get() [1]. As an attempt to handle OOM in a graceful way, we
have tried commit 5362544bebe85071 ("tty: don't panic on OOM in
tty_set_ldisc()"). But we reverted that attempt by commit a8983d01f9b7d600
("Revert "tty: don't panic on OOM in tty_set_ldisc()"") due to reproducible
crash. We should spend resource for finding and fixing race condition bugs
rather than complicate error paths for 2 * sizeof(void *) bytes allocation
failure.
syzbot is reporting crashes [1] triggered by memory allocation failure at
tty_ldisc_get() from tty_ldisc_restore(). While syzbot stops at WARN_ON()
due to panic_on_warn == true, panic_on_warn == false will after all trigger
an OOPS by dereferencing old->ops->num if IS_ERR(old) == true.
We can simplify tty_ldisc_restore() as three calls (old->ops->num, N_TTY,
N_NULL) to tty_ldisc_failto() in addition to avoiding possible error
pointer dereference.
If someone reports kernel panic triggered by forcing all memory allocations
for tty_ldisc_restore() to fail, we can consider adding __GFP_NOFAIL for
tty_ldisc_restore() case.
At least on droid 4 with control channel in ADM mode, there is no response
to Modem Status Command (MSC). Currently gsmtty_modem_update() expects to
have data in dlci->modem_rx unless debug & 2 is set. This means that on
droid 4, things only work if debug & 2 is set.
Let's fix the issue by ignoring empty dlci->modem_rx for ADM mode. In
the AMD mode, CMD_MSC will never respond and gsm_process_modem() won't
get called to set dlci->modem_rx.
And according to ts_127010v140000p.pdf, MSC is only relevant if basic
option is chosen, so let's test for that too.
Fixes: ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for control dlci") Cc: linux-serial@vger.kernel.org Cc: Alan Cox <alan@llwyncelyn.cymru> Cc: Dan Williams <dcbw@redhat.com> Cc: Jiri Prchal <jiri.prchal@aksignal.cz> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com> Cc: Michael Scott <michael.scott@linaro.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russ Gorby <russ.gorby@intel.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for
control dlci") added support for DLCI to stay in Asynchronous Disconnected
Mode (ADM). But we still get long delays waiting for commands to other
DLCI to complete:
This happens because gsm_control_send() sets cretries timer to T2 that is
by default set to 34. This will cause resend for T2 times for the control
frame. In ADM mode, we will never get a response so the control frame, so
retries are just delaying all the commands.
Let's fix the issue by setting DLCI_MODE_ADM flag after detecting the ADM
mode for the control DLCI. Then we can use that in gsm_control_send() to
set retries to 1. This means the control frame will be sent once allowing
the other end at an opportunity to switch from ADM to ABM mode.
Note that retries will be decremented in gsm_control_retransmit() so
we don't want to set it to 0 here.
Fixes: ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for control dlci") Cc: linux-serial@vger.kernel.org Cc: Alan Cox <alan@llwyncelyn.cymru> Cc: Dan Williams <dcbw@redhat.com> Cc: Jiri Prchal <jiri.prchal@aksignal.cz> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com> Cc: Michael Scott <michael.scott@linaro.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russ Gorby <russ.gorby@intel.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting kernel panic [1] triggered by memory allocation failure
at tty_ldisc_get() from tty_ldisc_init(). But since both tty_ldisc_get()
and caller of tty_ldisc_init() can cleanly handle errors, tty_ldisc_init()
does not need to call panic() when tty_ldisc_get() failed.
Wait until we have enough space in the virt queue to actually queue up
our request. Avoids the guest spinning in case we have a non-zero
amount of free entries but not enough for the request.
Cc: stable@vger.kernel.org Reported-by: Alain Magloire <amagloire@blackberry.com> Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-by: Dave Airlie <airlied@redhat.com> Link: http://patchwork.freedesktop.org/patch/msgid/20180403095904.11152-1-kraxel@redhat.com Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When out of memory and we can't add ctrl vq buffers,
probe fails. Unfortunately the error handling is
out of spec: it calls del_vqs without bothering
to reset the device first.
To fix, call the full cleanup function in this case.
Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Console driver is out of spec. The spec says:
A driver MUST NOT decrement the available idx on a live
virtqueue (ie. there is no way to “unexpose” buffers).
and it does exactly that by trying to detach unused buffers
without doing a device reset first.
Defer detaching the buffers until device unplug.
Of course this means we might get an interrupt for
a vq without an attached port now. Handle that by
discarding the consumed buffer.
Reported-by: Tiwei Bie <tiwei.bie@intel.com> Fixes: b3258ff1d6 ("virtio: Decrement avail idx on buffer detach") Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell Dock USB-audio device with 0bda:4014 is behaving notoriously
bad, and we have already applied some workaround to avoid the firmware
hiccup. Yet we still need to skip one thing, the Extension Unit at ID
4, which doesn't react correctly to the mixer ctl access.
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some boards, under heavy load, the EC firmware is
unable to complete commands even in one second. Increasing
the command completion timeout value to five seconds.
Reported-by: Quanxian Wang <quanxian.wang@intel.com> Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface") Cc: <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.
This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Add simple driver for libtransistor USB console.
This device is implemented in software:
https://github.com/reswitched/libtransistor/blob/development/lib/usb_serial.c
Signed-off-by: Collin May <collin@collinswebsite.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device
AMD suggests that a delay before xHC suspends can fix the issue.
I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.
It is incomplete and causes hangs on devices when shutting down. It
needs a much more "complete" fix in order to work properly. As that fix
has not been merged, revert this patch for now before it causes any more
problems.
Until the primary_crng is fully initialized, don't initialize the NUMA
crng nodes. Otherwise users of /dev/urandom on NUMA systems before
the CRNG is fully initialized can get very bad quality randomness. Of
course everyone should move to getrandom(2) where this won't be an
issue, but there's a lot of legacy code out there. This related to
CVE-2018-1108.
Currently in ext4_valid_block_bitmap() we expect the bitmap to be
positioned anywhere between 0 and s_blocksize clusters, but that's
wrong because the bitmap can be placed anywhere in the block group. This
causes false positives when validating bitmaps on perfectly valid file
system layouts. Fix it by checking whether the bitmap is within the group
boundary.
The problem can be reproduced using the following
mkfs -t ext3 -E stride=256 /dev/vdb1
mount /dev/vdb1 /mnt/test
cd /mnt/test
wget https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.16.3.tar.xz
tar xf linux-4.16.3.tar.xz
An privileged attacker can cause a crash by mounting a crafted ext4
image which triggers a out-of-bounds read in the function
ext4_valid_block_bitmap() in fs/ext4/balloc.c.
If ext4 tries to start a reserved handle via
jbd2_journal_start_reserved(), and the journal has been aborted, this
can result in a NULL pointer dereference. This is because the fields
h_journal and h_transaction in the handle structure share the same
memory, via a union, so jbd2_journal_start_reserved() will clear
h_journal before calling start_this_handle(). If this function fails
due to an aborted handle, h_journal will still be NULL, and the call
to jbd2_journal_free_reserved() will pass a NULL journal to
sub_reserve_credits().
This can be reproduced by running "kvm-xfstests -c dioread_nolock
generic/475".
Cc: stable@kernel.org # 3.11 Fixes: 8f7d89f36829b ("jbd2: transaction reservation support") Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the "insert range" fallocate operation, extents starting at the
range offset are shifted "right" (to a higher file offset) by the range
length. But, as shown by syzbot, it's not validated that this doesn't
cause extents to be shifted beyond EXT_MAX_BLOCKS. In that case
->ee_block can wrap around, corrupting the extent tree.
Fix it by returning an error if the space between the end of the last
extent and EXT4_MAX_BLOCKS is smaller than the range being inserted.
This bug can be reproduced by running the following commands when the
current directory is on an ext4 filesystem with a 4k block size:
Commit 5928c281524f (ACPI / video: Default lcd_only to true on Win8-ready
and newer machines) made only_lcd default to true on all machines where
acpi_osi_is_win8() returns true, including laptops.
The purpose of this is to avoid the bogus / non-working acpi backlight
interface which many newer BIOS-es define on desktop machines.
But this is causing a regression on some laptops, specifically on the
Dell XPS 13 2013 model, which does not have the LCD flag set for its
fully functional ACPI backlight interface.
Rather then DMI quirking our way out of this, this commits changes the
logic for setting only_lcd to true, to only do this on machines with
a desktop (or server) dmi chassis-type.
Note that we cannot simply only check the chassis-type and not register
the backlight interface based on that as there are some laptops and
tablets which have their chassis-type set to "3" aka desktop. Hopefully
the combination of checking the LCD flag, but only on devices with
a desktop(ish) chassis-type will avoid the needs for DMI quirks for this,
or at least limit the amount of DMI quirks which we need to a minimum.
Fixes: 5928c281524f (ACPI / video: Default lcd_only to true on Win8-ready and newer machines) Reported-and-tested-by: James Hogan <jhogan@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new CKD storage volume is defined at the storage server, Linux
may be relying on outdated information about that volume, which leads to
the following errors:
Fix this problem by using the up-to-date information provided during
online processing via the device specific SNEQ to detect the case of
outdated LCU data. If there is a difference, perform a re-read of that
data.
Cc: stable@vger.kernel.org Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Channel path descriptors have been seen as something stable (as
long as the chpid is configured). Recent tests have shown that the
descriptor can also be altered when the link state of a channel path
changes. Thus it is necessary to update the descriptor during
handling of resource accessibility events.
Cc: <stable@vger.kernel.org> Signed-off-by: Sebastian Ott <sebott@linux.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading to the end of a 720K disk results in an IO error instead of EOF
because the block layer thinks the disk has 2880 sectors. (Partly this
is a result of inverted logic of the ONEMEG_MEDIA bit that's now fixed.)
Initialize the density and head count in swim_add_floppy() to agree
with the device size passed to set_capacity() during drive probe.
Call set_capacity() again upon device open, after refreshing the density
and head count values.
In the floppy_find() function in swim.c is a call to
get_disk(swd->unit[drive].disk). The actual parameter to this call
can be a NULL pointer when drive == swd->floppy_count. This causes
an oops in get_disk().
The Sony drive status bits use active-low logic. The swim_readbit()
function converts that to 'C' logic for readability. Hence, the
sense of the names of the status bit macros should not be inverted.
Mostly they are correct. However, the TWOMEG_DRIVE, MFM_MODE and
TWOMEG_MEDIA macros have inverted sense (like MkLinux). Fix this
inconsistency and make the following patches less confusing.
The same problem affects swim3.c so fix that too.
No functional change.
The FDHD drive status bits are documented in sonydriv.cpp from MAME
and in swimiii.h from MkLinux.
Cc: Laurent Vivier <lvivier@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: Jens Axboe <axboe@kernel.dk> Cc: stable@vger.kernel.org # v4.14+ Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'eject' shell command may send various different ioctl commands.
This leads to error messages on the console even though the FDEJECT
ioctl succeeds.
The SWIM chip is compatible with GCR-mode Sony 400K/800K drives but
this driver only supports MFM mode. Therefore only Sony FDHD drives
are supported. Skip incompatible drives.
There's no need to call ioremap() for the SWIM address range, as it lies
within the usual IO device region at 0x5000 0000, which has already been
mapped by head.S.
Remove the redundant ioremap() and iounmap() calls to fix the hang.
Cc: Laurent Vivier <lvivier@redhat.com> Cc: stable@vger.kernel.org # v4.14+ Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsnotify() acquires a reference to a fsnotify_mark_connector through
the SRCU-protected pointer to_tell->i_fsnotify_marks. However, it
appears that no precautions are taken in fsnotify_put_mark() to
ensure that fsnotify() drops its reference to this
fsnotify_mark_connector before assigning a value to its 'destroy_next'
field. This can result in fsnotify_put_mark() assigning a value
to a connector's 'destroy_next' field right before fsnotify() tries to
traverse the linked list referenced by the connector's 'list' field.
Since these two fields are members of the same union, this behavior
results in a kernel panic.
This issue is resolved by moving the connector's 'destroy_next' field
into the object pointer union. This should work since the object pointer
access is protected by both a spinlock and the value of the 'flags'
field, and the 'flags' field is cleared while holding the spinlock in
fsnotify_put_mark() before 'destroy_next' is updated. It shouldn't be
possible for another thread to accidentally read from the object pointer
after the 'destroy_next' field is updated.
The offending behavior here is extremely unlikely; since
fsnotify_put_mark() removes references to a connector (specifically,
it ensures that the connector is unreachable from the inode it was
formerly attached to) before updating its 'destroy_next' field, a
sizeable chunk of code in fsnotify_put_mark() has to execute in the
short window between when fsnotify() acquires the connector reference
and saves the value of its 'list' field. On the HEAD kernel, I've only
been able to reproduce this by inserting a udelay(1) in fsnotify().
However, I've been able to reproduce this issue without inserting a
udelay(1) anywhere on older unmodified release kernels, so I believe
it's worth fixing at HEAD.
References: https://bugzilla.kernel.org/show_bug.cgi?id=199437 Fixes: 08991e83b7286635167bab40927665a90fb00d81 CC: stable@vger.kernel.org Signed-off-by: Robert Kolchmeyer <rkolchmeyer@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cast is wrong. "cdi->capacity" is an int and "arg" is an unsigned
long. The way the check is written now, if one of the high 32 bits is
set then we could read outside the info->slots[] array.
This bug is pretty old and it predates git.
Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First generation MPT Fusion controllers can not translate WRITE SAME
when the attached device is a SATA drive. Disable WRITE SAME support.
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting NULL pointer dereference at xattr_getsecurity() [1],
for cap_inode_getsecurity() is returning sizeof(struct vfs_cap_data) when
memory allocation failed. Return -ENOMEM if memory allocation failed.
There are still build errors with this patch applied, and the upstream
patches do not seem to apply anymore, so reverting this patch seems like
the best thing to do at this point in time.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Михаил Носов <drdeimosnn@gmail.com> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Evgeny Baskakov <ebaskakov@nvidia.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vdd_log has no consumer and therefore will not be set to a specific
voltage. Still the PWM output pin gets configured and thence the vdd_log
output voltage will changed from it's default. Depending on the idle
state of the PWM this will slightly over or undervoltage the logic supply
of the RK3399 and cause instability with GbE (undervoltage) and PCIe
(overvoltage). Since the default value set by a voltage divider is the
correct supply voltage and we don't need to change it during runtime we
remove the rail from the devicetree completely so the PWM pin will not
be configured.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Cc: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch:
"microblaze: Setup proper dependency for optimized lib functions"
(sha1: 7b6ce52be3f86520524711a6f33f3866f9339694)
didn't setup all dependencies properly.
Optimized lib functions in C are also present for little endian
and optimized library functions in assembler are implemented only for
big endian version.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main linker script vmlinux.lds.S for the kernel image merges
the expoline code patch tables into two section ".nospec_call_table"
and ".nospec_return_table". This is *not* done for the modules,
there the sections retain their original names as generated by gcc:
".s390_indirect_call", ".s390_return_mem" and ".s390_return_reg".
The module_finalize code has to check for the compiler generated
section names, otherwise no code patching is done. This slows down
the module code in case of "spectre_v2=off".
Cc: stable@vger.kernel.org # 4.16 Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches") Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_EXPOLINE_AUTO=y the call of spectre_v2_auto_early() via
early_initcall is done *after* the early_param functions. This
overwrites any settings done with the nobp/no_spectre_v2/spectre_v2
parameters. The code patching for the kernel is done after the
evaluation of the early parameters but before the early_initcall
is done. The end result is a kernel image that is patched correctly
but the kernel modules are not.
Make sure that the nospec auto detection function is called before the
early parameters are evaluated and before the code patching is done.
Fixes: 6e179d64126b ("s390: add automatic detection of the spectre defense") Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a boot message if either of the spectre defenses is active.
The message is
"Spectre V2 mitigation: execute trampolines."
or "Spectre V2 mitigation: limited branch prediction."
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when a system call is interrupted we might call the critical section
cleanup handler that re-does some of the operations. When we are between
.Lsysc_vtime and .Lsysc_do_svc we might also redo the saving of the
problem state registers r0-r7:
.Lcleanup_system_call:
[...]
0: # update accounting time stamp
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
# set up saved register r11
lg %r15,__LC_KERNEL_STACK
la %r9,STACK_FRAME_OVERHEAD(%r15)
stg %r9,24(%r11) # r11 pt_regs pointer
# fill pt_regs
mvc __PT_R8(64,%r9),__LC_SAVE_AREA_SYNC
---> stmg %r0,%r7,__PT_R0(%r9)
The problem is now, that we might have already zeroed out r0.
The fix is to move the zeroing of r0 after sysc_do_svc.
Reported-by: Farhan Ali <alifm@linux.vnet.ibm.com> Fixes: 7041d28115e91 ("s390: scrub registers on kernel entry and KVM exit") Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system call path can be interrupted before the switch back to the
standard branch prediction with BPENTER has been done. The critical
section cleanup code skips forward to .Lsysc_do_svc and bypasses the
BPENTER. In this case the kernel and all subsequent code will run with
the limited branch prediction.
Fixes: eacf67eb9b32 ("s390: run user space and KVM guests with modified branch prediction") Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the guest runs with bp isolation when doing a SIE instruction,
we must also run the nested guest with bp isolation when emulating
that SIE instruction.
This is done by activating BPBC in the lpar, which acts as an override
for lower level guests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_EXPOLINE to enable the use of the new -mindirect-branch= and
-mfunction_return= compiler options to create a kernel fortified against
the specte v2 attack.
With CONFIG_EXPOLINE=y all indirect branches will be issued with an
execute type instruction. For z10 or newer the EXRL instruction will
be used, for older machines the EX instruction. The typical indirect
call
basr %r14,%r1
is replaced with a PC relative call to a new thunk
brasl %r14,__s390x_indirect_jump_r1
The thunk contains the EXRL/EX instruction to the indirect branch
__s390x_indirect_jump_r1:
exrl 0,0f
j .
0: br %r1
The detour via the execute type instruction has a performance impact.
To get rid of the detour the new kernel parameter "nospectre_v2" and
"spectre_v2=[on,off,auto]" can be used. If the parameter is specified
the kernel and module code will be patched at runtime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define TIF_ISOLATE_BP and TIF_ISOLATE_BP_GUEST and add the necessary
plumbing in entry.S to be able to run user space and KVM guests with
limited branch prediction.
To switch a user space process to limited branch prediction the
s390_isolate_bp() function has to be call, and to run a vCPU of a KVM
guest associated with the current task with limited branch prediction
call s390_isolate_bp_guest().
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the PPA instruction to the system entry and exit path to switch
the kernel to a different branch prediction behaviour. The instructions
are added via CPU alternatives and can be disabled with the "nospec"
or the "nobp=0" kernel parameter. If the default behaviour selected
with CONFIG_KERNEL_NOBP is set to "n" then the "nobp=1" parameter can be
used to enable the changed kernel branch prediction.
To be able to switch off specific CPU alternatives with kernel parameters
make a copy of the facility bit mask provided by STFLE and use the copy
for the decision to apply an alternative.
Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear all user space registers on entry to the kernel and all KVM guest
registers on KVM guest exit if the register does not contain either a
parameter or a result value.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new firmware interfaces for branch prediction behaviour changes
are transparently available for the guest. Nevertheless, there is
new state attached that should be migrated and properly resetted.
Provide a mechanism for handling reset, migration and VSIE.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[Changed capability number to 152. - Radim] Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the CPU_ALTERNATIVES config option and enable the code
unconditionally. The config option was only added to avoid a conflict
with the named saved segment support. Since that code is gone there is
no reason to keep the CPU_ALTERNATIVES config option.
Just enable it unconditionally to also reduce the number of config
options and make it less likely that something breaks.
Implement CPU alternatives, which allows to optionally patch newer
instructions at runtime, based on CPU facilities availability.
A new kernel boot parameter "noaltinstr" disables patching.
Current implementation is derived from x86 alternatives. Although
ideal instructions padding (when altinstr is longer then oldinstr)
is added at compile time, and no oldinstr nops optimization has to be
done at runtime. Also couple of compile time sanity checks are done:
1. oldinstr and altinstr must be <= 254 bytes long,
2. oldinstr and altinstr must not have an odd length.
Programming vids (adding or removing them) still passes
guest-endian values in the DMA buffer. That's wrong
if guest is big-endian and when virtio 1 is enabled.
Note: this is on top of a previous patch:
virtio_net: split out ctrl buffer
Fixes: 9465a7a6f ("virtio_net: enable v1.0 support") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending control commands, virtio net sets up several buffers for
DMA. The buffers are all part of the net device which means it's
actually allocated by kvmalloc so it's in theory (on extreme memory
pressure) possible to get a vmalloc'ed buffer which on some platforms
means we can't DMA there.
Fix up by moving the DMA buffers into a separate structure.
Reported-by: Mikulas Patocka <mpatocka@redhat.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b747 ("net: ethernet: ti: cpsw: add multi queue support") Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SOCK_ZAPPED socket, we don't need to care about llc->sap,
so we should just skip these refcount functions in this case.
Fixes: f7e43672683b ("llc: hold llc_sap before release_sock()") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
llc->sap is refcount'ed and llc_sap_remove_socket() is paired
with llc_sap_add_socket(). This can be amended by holding its refcount
before llc_sap_remove_socket() and releasing it after release_sock().
Reported-by: <syzbot+6e181fc95081c2cf9051@syzkaller.appspotmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch checks if sk buffer is available to dererence ife header. If
not then NULL will returned to signal an malformed ife packet. This
avoids to crashing the kernel from outside.
Signed-off-by: Alexander Aring <aring@mojatatu.com> Reviewed-by: Yotam Gigi <yotam.gi@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is currently no handling to check on a invalid tlv length. This
patch adds such handling to avoid killing the kernel with a malformed
ife packet.
Signed-off-by: Alexander Aring <aring@mojatatu.com> Reviewed-by: Yotam Gigi <yotam.gi@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcp: clear tp->packets_out when purging write queue
Clear tp->packets_out when purging the write queue, otherwise
tcp_rearm_rto() mistakenly assumes TCP write queue is not empty.
This results in NULL pointer dereference.
Also, remove the redundant `tp->packets_out = 0` from
tcp_disconnect(), since tcp_disconnect() calls
tcp_write_queue_purge().
We need to record stats for received metadata that we dont know how
to process. Have find_decode_metaid() return -ENOENT to capture this.
Signed-off-by: Alexander Aring <aring@mojatatu.com> Reviewed-by: Yotam Gigi <yotam.gi@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strp_data_ready resets strp->need_bytes to 0 if strp_peek_len indicates
that the remainder of the message has been received. However,
do_strp_work does not reset strp->need_bytes to 0. If do_strp_work
completes a partial message, the value of strp->need_bytes will continue
to reflect the needed bytes of the previous message, causing
future invocations of strp_data_ready to return early if
strp->need_bytes is less than strp_peek_len. Resetting strp->need_bytes
to 0 in __strp_recv on handing a full message to the upper layer solves
this problem.
__strp_recv also calculates strp->need_bytes using stm->accum_len before
stm->accum_len has been incremented by cand_len. This can cause
strp->need_bytes to be equal to the full length of the message instead
of the full length minus the accumulated length. This, in turn, causes
strp_data_ready to return early, even when there is sufficient data to
complete the partial message. Incrementing stm->accum_len before using
it to calculate strp->need_bytes solves this problem.
Found while testing net/tls_sw recv path.
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct sock's sk_rcvtimeo is initialized to
LONG_MAX/MAX_SCHEDULE_TIMEOUT in sock_init_data. Calling
mod_delayed_work with a timeout of LONG_MAX causes spurious execution of
the work function. timer->expires is set equal to jiffies + LONG_MAX.
When timer_base->clk falls behind the current value of jiffies,
the delta between timer_base->clk and jiffies + LONG_MAX causes the
expiration to be in the past. Returning early from strp_start_timer if
timeo == LONG_MAX solves this problem.
Found while testing net/tls_sw recv path.
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Reviewed-by: Tejun Heo <tj@kernel.org> Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pf->cmp_addr() is called before binding a v6 address to the sock. It
should not check ports, like in sctp_inet_cmp_addr.
But sctp_inet6_cmp_addr checks the addr by invoking af(6)->cmp_addr,
sctp_v6_cmp_addr where it also compares the ports.
This would cause that setsockopt(SCTP_SOCKOPT_BINDX_ADD) could bind
multiple duplicated IPv6 addresses after Commit 40b4f0fd74e4 ("sctp:
lack the check for ports in sctp_v6_cmp_addr").
This patch is to remove af->cmp_addr called in sctp_inet6_cmp_addr,
but do the proper check for both v6 addrs and v4mapped addrs.
v1->v2:
- define __sctp_v6_cmp_addr to do the common address comparison
used for both pf and af v6 cmp_addr.
Fixes: 40b4f0fd74e4 ("sctp: lack the check for ports in sctp_v6_cmp_addr") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller spotted an old bug which leads to reading skb beyond tail by 4
bytes on vlan tagged packets.
This is caused because skb_vlan_tagged_multi() did not check
skb_headlen.
Fixes: 58e998c6d239 ("offloading: Force software GSO for multiple vlan tags.") Reported-and-tested-by: syzbot+0bbe42c764feafa82c5a@syzkaller.appspotmail.com Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before syzbot/KMSAN bites, add the missing policy for TIPC_NLA_NET_ADDR
Fixes: 27c21416727a ("tipc: add net set to new netlink api") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates to the bitfields in struct packet_sock are not atomic.
Serialize these read-modify-write cycles.
Move po->running into a separate variable. Its writes are protected by
po->bind_lock (except for one startup case at packet_create). Also
replace a textual precondition warning with lockdep annotation.
All others are set only in packet_setsockopt. Serialize these
updates by holding the socket lock. Analogous to other field updates,
also hold the lock when testing whether a ring is active (pg_vec).
Fixes: 8dc419447415 ("[PACKET]: Add optional checksum computation for recvmsg") Reported-by: DaeRyong Jeong <threeearcat@gmail.com> Reported-by: Byoungyoung Lee <byoungyoung@purdue.edu> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same fix in Commit dbe173079ab5 ("bridge: fix netconsole
setup over bridge") is also needed for team driver.
While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().
v1->v2:
- fix it in a better way, as does bridge.
Fixes: 0fb52a27a04a ("team: cleanup netpoll clode") Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling shutdown with SHUT_RD and SHUT_RDWR for a listening SMC socket
crashes, because
commit 127f49705823 ("net/smc: release clcsock from tcp_listen_worker")
releases the internal clcsock in smc_close_active() and sets smc->clcsock
to NULL.
For SHUT_RD the smc_close_active() call is removed.
For SHUT_RDWR the kernel_sock_shutdown() call is omitted, since the
clcsock is already released.
Fixes: 127f49705823 ("net/smc: release clcsock from tcp_listen_worker") Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reported-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When parsing the options provided by the user space,
team_nl_cmd_options_set() insert them in a temporary list to send
multiple events with a single message.
While each option's attribute is correctly validated, the code does
not check for duplicate entries before inserting into the event
list.
Exploiting the above, the syzbot was able to trigger the following
splat:
This changeset addresses the avoiding list_add() if the current
option is already present in the event list.
Reported-and-tested-by: syzbot+4d4af685432dc0e56c91@syzkaller.appspotmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Fixes: 2fcdb2c9e659 ("team: allow to send multiple set events in one message") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log