Frank Sae [Sun, 1 Sep 2024 08:35:25 +0000 (01:35 -0700)]
net: phy: Optimize phy speed mask to be compatible to yt8821
yt8521 and yt8531s as Gigabit transceiver use bit15:14(bit9 reserved
default 0) as phy speed mask, yt8821 as 2.5G transceiver uses bit9 bit15:14
as phy speed mask.
Be compatible to yt8821, reform phy speed mask and phy speed macro.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* tag 'linux-can-next-for-6.12-20240904-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: rockchip_canfd: add support for CAN_CTRLMODE_BERR_REPORTING
can: rockchip_canfd: add support for CAN_CTRLMODE_LOOPBACK
can: rockchip_canfd: add hardware timestamping support
can: rockchip_canfd: enable full TX-FIFO depth of 2
can: rockchip_canfd: prepare to use full TX-FIFO depth
can: rockchip_canfd: add stats support for errata workarounds
can: rockchip_canfd: rkcanfd_get_berr_counter_corrected(): work around broken {RX,TX}ERRORCNT register
can: rockchip_canfd: implement workaround for erratum 12
can: rockchip_canfd: implement workaround for erratum 6
can: rockchip_canfd: add TX PATH
can: rockchip_canfd: rkcanfd_register_done(): add warning for erratum 5
can: rockchip_canfd: rkcanfd_handle_rx_int_one(): implement workaround for erratum 5: check for empty FIFO
can: rockchip_canfd: add notes about known issues
can: rockchip_canfd: add support for rk3568v3
can: rockchip_canfd: add quirk for broken CAN-FD support
can: rockchip_canfd: add quirks for errata workarounds
can: rockchip_canfd: add driver for Rockchip CAN-FD controller
dt-bindings: can: rockchip_canfd: add rockchip CAN-FD controller
====================
Chen Ni [Wed, 4 Sep 2024 01:50:03 +0000 (09:50 +0800)]
ptp: ptp_idt82p33: Convert comma to semicolon
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Hongbo Li [Wed, 4 Sep 2024 01:49:56 +0000 (09:49 +0800)]
net: dsa: felix: Annotate struct action_gate_entry with __counted_by
Add the __counted_by compiler attribute to the flexible array member
entries to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
====================
Bonding: support new xfrm state offload functions
Add 2 new xfrm state offload functions xdo_dev_state_advance_esn and
xdo_dev_state_update_stats for bonding. The xdo_dev_state_free will be
added by Jianbo's patchset [1]. I will add the bonding xfrm policy offload
in future.
v7: no update, just rebase the code.
v6: Use "Return: " based on ./scripts/kernel-doc (Simon Horman)
v5: Rebase to latest net-next, update function doc (Jakub Kicinski)
v4: Ratelimit pr_warn (Sabrina Dubroca)
v3: Re-format bond_ipsec_dev, use slave_warn instead of WARN_ON (Nikolay Aleksandrov)
Fix bond_ipsec_dev defination, add *. (Simon Horman, kernel test robot)
Fix "real" typo (kernel test robot)
v2: Add a function to process the common device checking (Nikolay Aleksandrov)
Remove unused variable (Simon Horman)
v1: lore.kernel.org/netdev/20240816035518.203704-1-liuhangbin@gmail.com
====================
Hangbin Liu [Wed, 4 Sep 2024 00:34:57 +0000 (08:34 +0800)]
bonding: support xfrm state update
The patch add xfrm statistics update for bonding IPsec offload.
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Acked-by: Jay Vosburgh <jv@jvosburgh.net> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Hangbin Liu [Wed, 4 Sep 2024 00:34:56 +0000 (08:34 +0800)]
bonding: Add ESN support to IPSec HW offload
Currently, users can see that bonding supports IPSec HW offload via ethtool.
However, this functionality does not work with NICs like Mellanox cards when
ESN (Extended Sequence Numbers) is enabled, as ESN functions are not yet
supported. This patch adds ESN support to the bonding IPSec device offload,
ensuring proper functionality with NICs that support ESN.
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Acked-by: Jay Vosburgh <jv@jvosburgh.net> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Hangbin Liu [Wed, 4 Sep 2024 00:34:55 +0000 (08:34 +0800)]
bonding: add common function to check ipsec device
This patch adds a common function to check the status of IPSec devices.
This function will be useful for future implementations, such as IPSec ESN
and state offload callbacks.
Suggested-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Acked-by: Jay Vosburgh <jv@jvosburgh.net> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sean Anderson [Tue, 3 Sep 2024 18:49:12 +0000 (14:49 -0400)]
net: cadence: macb: Enable software IRQ coalescing by default
This NIC doesn't have hardware IRQ coalescing. Under high load,
interrupts can adversely affect performance. To mitigate this, enable
software IRQ coalescing by default. On my system this increases receive
throughput with iperf3 from 853 MBit/sec to 934 MBit/s, decreases
interrupts from 69489/sec to 2016/sec, and decreases CPU utilization
from 27% (4x Cortex-A53) to 14%. Latency is not affected (as far as I
can tell).
When reading registers from the PHY using the SIOCGMIIREG IOCTL any
errors returned from either mdiobus_read() or mdiobus_c45_read() are
ignored, and parts of the returned error is passed as the register value
back to user-space.
For example, if mdiobus_c45_read() is used with a bus that do not
implement the read_c45() callback -EOPNOTSUPP is returned. This is
however directly stored in mii_data->val_out and returned as the
registers content. As val_out is a u16 the error code is truncated and
returned as a plausible register value.
Fix this by first checking the return value for errors before returning
it as the register content.
Li Zetao [Tue, 3 Sep 2024 14:33:43 +0000 (22:33 +0800)]
pds_core: Remove redundant null pointer checks
Since the debugfs_create_dir() never returns a null pointer, checking
the return value for a null pointer is redundant, and using IS_ERR is
safe enough.
Li Zetao [Tue, 3 Sep 2024 14:31:49 +0000 (22:31 +0800)]
ionic: Remove redundant null pointer checks in ionic_debugfs_add_qcq()
Since the debugfs_create_dir() never returns a null pointer, checking
the return value for a null pointer is redundant, and using IS_ERR is
safe enough.
Jakub Kicinski [Wed, 4 Sep 2024 23:57:13 +0000 (16:57 -0700)]
Merge branch 'unmask-upper-dscp-bits-part-3'
Ido Schimmel says:
====================
Unmask upper DSCP bits - part 3
tl;dr - This patchset continues to unmask the upper DSCP bits in the
IPv4 flow key in preparation for allowing IPv4 FIB rules to match on
DSCP. No functional changes are expected.
The TOS field in the IPv4 flow key ('flowi4_tos') is used during FIB
lookup to match against the TOS selector in FIB rules and routes.
It is currently impossible for user space to configure FIB rules that
match on the DSCP value as the upper DSCP bits are either masked in the
various call sites that initialize the IPv4 flow key or along the path
to the FIB core.
In preparation for adding a DSCP selector to IPv4 and IPv6 FIB rules, we
need to make sure the entire DSCP value is present in the IPv4 flow key.
This patchset continues to unmask the upper DSCP bits, but this time in
the output route path, specifically in the callers of
ip_route_output_ports().
The next patchset (last) will handle the callers of
ip_route_output_key(). Split from this patchset to avoid going over the
15 patches limit.
No functional changes are expected as commit 1fa3314c14c6 ("ipv4:
Centralize TOS matching") moved the masking of the upper DSCP bits to
the core where 'flowi4_tos' is matched against the TOS selector.
====================
ipv6: sit: Unmask upper DSCP bits in ipip6_tunnel_bind_dev()
Unmask the upper DSCP bits when calling ip_route_output_ports() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
ip6_tunnel: Unmask upper DSCP bits in ip4ip6_err()
Unmask the upper DSCP bits when calling ip_route_output_ports() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
ipv4: ipmr: Unmask upper DSCP bits in ipmr_queue_xmit()
Unmask the upper DSCP bits when calling ip_route_output_ports() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
The function is passed the full DS field in its 'tos' argument by its
two callers. It then masks the upper DSCP bits using RT_TOS() when
passing it to ip_route_output_ports().
Unmask the upper DSCP bits when passing 'tos' to ip_route_output_ports()
so that in the future it could perform the FIB lookup according to the
full DSCP value.
Chen Ni [Wed, 4 Sep 2024 01:44:41 +0000 (09:44 +0800)]
selftests: net: convert comma to semicolon
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
ipv4: Fix user space build failure due to header change
RT_TOS() from include/uapi/linux/in_route.h is defined using
IPTOS_TOS_MASK from include/uapi/linux/ip.h. This is problematic for
files such as include/net/ip_fib.h that want to use RT_TOS() as without
including both header files kernel compilation fails:
In file included from ./include/net/ip_fib.h:25,
from ./include/net/route.h:27,
from ./include/net/lwtunnel.h:9,
from net/core/dst.c:24:
./include/net/ip_fib.h: In function ‘fib_dscp_masked_match’:
./include/uapi/linux/in_route.h:31:32: error: ‘IPTOS_TOS_MASK’ undeclared (first use in this function)
31 | #define RT_TOS(tos) ((tos)&IPTOS_TOS_MASK)
| ^~~~~~~~~~~~~~
./include/net/ip_fib.h:440:45: note: in expansion of macro ‘RT_TOS’
440 | return dscp == inet_dsfield_to_dscp(RT_TOS(fl4->flowi4_tos));
Therefore, cited commit changed linux/in_route.h to include linux/ip.h.
However, as reported by David, this breaks iproute2 compilation due
overlapping definitions between linux/ip.h and
/usr/include/netinet/ip.h:
In file included from ../include/uapi/linux/in_route.h:5,
from iproute.c:19:
../include/uapi/linux/ip.h:25:9: warning: "IPTOS_TOS" redefined
25 | #define IPTOS_TOS(tos) ((tos)&IPTOS_TOS_MASK)
| ^~~~~~~~~
In file included from iproute.c:17:
/usr/include/netinet/ip.h:222:9: note: this is the location of the previous definition
222 | #define IPTOS_TOS(tos) ((tos) & IPTOS_TOS_MASK)
Fix by changing include/net/ip_fib.h to include linux/ip.h. Note that
usage of RT_TOS() should not spread further in the kernel due to recent
work in this area.
Fixes: 1fa3314c14c6 ("ipv4: Centralize TOS matching") Reported-by: David Ahern <dsahern@kernel.org> Closes: https://lore.kernel.org/netdev/2f5146ff-507d-4cab-a195-b28c0c9e654e@kernel.org/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Guillaume Nault <gnault@redhat.com> Link: https://patch.msgid.link/20240903133554.2807343-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
James Chapman [Tue, 3 Sep 2024 11:35:47 +0000 (12:35 +0100)]
l2tp: remove unneeded null check in l2tp_v2_session_get_next
Commit aa92c1cec92b ("l2tp: add tunnel/session get_next helpers") uses
idr_get_next APIs to iterate over l2tp session IDR lists. Sessions in
l2tp_v2_session_idr always have a non-null session->tunnel pointer
since l2tp_session_register sets it before inserting the session into
the IDR. Therefore the null check on session->tunnel in
l2tp_v2_session_get_next is redundant and can be removed. Removing the
check avoids a warning from lkp.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/r/202408111407.HtON8jqa-lkp@intel.com/ CC: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: James Chapman <jchapman@katalix.com> Acked-by: Tom Parkin <tparkin@katalix.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240903113547.1261048-1-jchapman@katalix.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: mana: Improve mana_set_channels() in low mem conditions
The mana_set_channels() function requires detaching the mana
driver and reattaching it with changed channel values.
During this operation if the system is low on memory, the reattach
might fail, causing the network device being down.
To avoid this we pre-allocate buffers at the beginning of set operation,
to prevent complete network loss
Marc Kleine-Budde [Wed, 4 Sep 2024 12:48:17 +0000 (14:48 +0200)]
Merge patch series "can: rockchip_canfd: add support for CAN-FD IP core found on Rockchip RK3568"
Marc Kleine-Budde <mkl@pengutronix.de> says:
This series adds support for the CAN-FD IP core found on the Rockchip
RK3568.
The IP core is a bit complicated and has several documented errata.
The driver is added in several stages, first the base driver including
the RX-path. Then several workarounds for errata and the TX-path, and
finally features like hardware time stamping, loop-back mode and
bus error reporting.
Marc Kleine-Budde [Thu, 18 Jan 2024 07:54:23 +0000 (08:54 +0100)]
can: rockchip_canfd: enable full TX-FIFO depth of 2
The previous commit prepared the TX path to make use of the full
TX-FIFO depth as much as possible. Increase the available TX-FIFO
depth to the hardware maximum of 2.
Marc Kleine-Budde [Wed, 17 Jan 2024 17:56:35 +0000 (18:56 +0100)]
can: rockchip_canfd: prepare to use full TX-FIFO depth
So far the TX-FIFO is only used with a depth of 1, although the
hardware offers a depth of 2.
The workaround for the chips that are affected by erratum 6, i.e. EFF
frames may be send as standard frames, is to re-send the EFF frame.
This means the driver cannot queue the next frame for sending, as long
ad the EFF frame has not been successfully send out.
Introduce rkcanfd_get_effective_tx_free() that returns "0" space in
the TX-FIFO if an EFF frame is pending and the actual free space in
the TX-FIFO otherwise. Then replace rkcanfd_get_tx_free() with
rkcanfd_get_effective_tx_free() everywhere.
Marc Kleine-Budde [Thu, 14 Dec 2023 13:45:09 +0000 (14:45 +0100)]
can: rockchip_canfd: add stats support for errata workarounds
The driver contains workarounds for some of the rk3568v2 errata. Add
ethtool-based statistics ("ethtool -S") to track how often an erratum
workaround was needed.
Marc Kleine-Budde [Sun, 10 Dec 2023 13:43:14 +0000 (14:43 +0100)]
can: rockchip_canfd: rkcanfd_get_berr_counter_corrected(): work around broken {RX,TX}ERRORCNT register
Tests show that sometimes both CAN bus error counters read 0x0, even
if the controller is in warning mode
(RKCANFD_REG_STATE_ERROR_WARNING_STATE in RKCANFD_REG_STATE
set).
To work around this issue, if both error counters read from hardware
are 0x0, use the structure priv->bec, otherwise save the read value in
priv->bec.
In rkcanfd_handle_rx_int_one() decrement the priv->bec.rxerr for
successfully RX'ed CAN frames.
In rkcanfd_handle_tx_done_one() decrement the priv->bec.txerr for
successfully TX'ed CAN frames.
Marc Kleine-Budde [Fri, 24 Nov 2023 07:54:32 +0000 (08:54 +0100)]
can: rockchip_canfd: implement workaround for erratum 12
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| A dominant bit at the third bit of the intermission may cause a
| transmission error.
|
| When sampling the third bit of the intermission as a dominant bit, if
| tx_req is configured to transmit extended frames at this time, the
| extended frame may be sent to the bus in the format of a standard
| frame. The extended frame will be sent as a standard frame and will not
| result in error frames
Turn on "Interframe Spaceing RX Mode" only during TX to work around
erratum 12, according to rock-chip:
| Spaceing RX Mode = 1, the third Bit between frames cannot receive
| and send, and the fourth Bit begins to receive and send.
|
| Spaceing RX Mode = 0, allowing the third Bit between frames to
| receive and send.
Marc Kleine-Budde [Fri, 24 Nov 2023 08:27:00 +0000 (09:27 +0100)]
can: rockchip_canfd: implement workaround for erratum 6
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| The CAN controller's transmission of extended frames may
| intermittently change into standard frames.
|
| When using the CAN controller to send extended frames, if the
| 'tx_req' is configured as 1 and coincides with the internal
| transmission point, the extended frame will be transmitted onto the
| bus in the format of a standard frame.
To work around Erratum 6, the driver is in self-receiving mode (RXSTX)
and all received CAN frames are passed through rkcanfd_rxstx_filter().
Add a check in rkcanfd_rxstx_filter() whether the received frame
corresponds to the current outgoing frame, but the extended CAN ID has
been mangled to a standard ID. In this case re-send the original CAN
frame.
Marc Kleine-Budde [Fri, 24 Nov 2023 20:37:36 +0000 (21:37 +0100)]
can: rockchip_canfd: add TX PATH
The IP core has a TX event FIFO. In other IP cores, this type of FIFO
usually contains the events that a CAN frame has been successfully
sent. However, the IP core on the rk3568v2 the FIFO also holds events
of unsuccessful transmission attempts.
It turned out that the best way to work around this problem is to set
the IP core to self-receive mode (RXSTX), filter out the self-received
frames and insert them into the complete TX path.
Add a pair new functions to check if 2 struct canfd_frame are equal.
The 1st checks if the header of the CAN frames are equal, the 2nd
checks if the data portion are equal:
Marc Kleine-Budde [Tue, 12 Dec 2023 12:57:55 +0000 (13:57 +0100)]
can: rockchip_canfd: rkcanfd_register_done(): add warning for erratum 5
Tests on the rk3568v2 and rk3568v3 show that a reduced "baudclk" (e.g.
80MHz, compared to the standard 300MHz) significantly increases the
possibility of incorrect FIFO counters, i.e. erratum 5.
Print an info message if the clock is below the known good value of
300MHz.
Marc Kleine-Budde [Thu, 4 Jan 2024 09:45:38 +0000 (10:45 +0100)]
can: rockchip_canfd: rkcanfd_handle_rx_int_one(): implement workaround for erratum 5: check for empty FIFO
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| Erratum 5: Counters related to the TXFIFO and RXFIFO exhibit
| abnormal counting behavior.
|
| Due to a bug in the cross-asynchronous logic of the enable signals
| for rx_fifo_cnt and txe_fifo_frame_cnt counters, the counts of these
| two counters become inaccurate. This issue has resulted in the
| inability to use the TXFIFO and RXFIFO functions.
The errata sheet mentioned above states that only the rk3568v2 is
affected by this erratum, but tests with the rk3568v2 and rk3568v3
show that the RX_FIFO_CNT is sometimes too high. This leads to CAN
frames being read from the FIFO, which is then already empty.
Further tests on the rk3568v2 and rk3568v3 show that in this
situation (i.e. empty FIFO) all elements of the FIFO
header (frameinfo, id, ts) contain the same data.
On the rk3568v2 and rk3568v3, this problem only occurs extremely
rarely with the standard clock of 300 MHz, but almost immediately at
80 MHz.
To workaround this problem, check for empty FIFO with
rkcanfd_fifo_header_empty() in rkcanfd_handle_rx_int_one() and exit
early.
Marc Kleine-Budde [Tue, 19 Dec 2023 11:33:30 +0000 (12:33 +0100)]
can: rockchip_canfd: add quirk for broken CAN-FD support
The errata sheets doesn't say anything about CAN-FD, but tests on the
rk3568v2 and rk3568v3 show that receiving certain CAN-FD frames
triggers an Error Interrupt.
Marc Kleine-Budde [Wed, 11 Oct 2023 14:02:32 +0000 (16:02 +0200)]
can: rockchip_canfd: add driver for Rockchip CAN-FD controller
Add driver for the Rockchip CAN-FD controller.
The IP core on the rk3568v2 SoC has 12 documented errata. Corrections
for these errata will be added in the upcoming patches.
Since several workarounds are required for the TX path, only add the
base driver that only implements the RX path.
Although the RX path implements CAN-FD support, it's not activated in
ctrlmode_supported, as the IP core in the rk3568v2 has problems with
receiving or sending certain CAN-FD frames.
Add support for group stats for mac. The fbnic_set_counter help preserve
the default values for counters which are not touched by the driver.
The 'reset' flag in 'get_eth_mac_stats' allows to choose between
resetting the counter to recent most value or fetching the aggregated
values of the counter.
The 'fbnic_stat_rd64' read 64b stats counters in an atomic fashion using
read-read-read approach. This allows to isolate cases where counter is
moving too fast making accuracy of the counter questionable.
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool ops support and enable 'get_drvinfo' for fbnic. The driver
provides firmware version information while the driver name and bus
information is provided by ethtool_get_drvinfo().
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Xing [Mon, 2 Sep 2024 16:06:10 +0000 (00:06 +0800)]
selftests: add selftest for UDP SO_PEEK_OFF support
Add the SO_PEEK_OFF selftest for UDP. In this patch, I mainly do
three things:
1. rename tcp_so_peek_off.c
2. adjust for UDP protocol
3. add selftests into it
Suggested-by: Jon Maloy <jmaloy@redhat.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jason Xing <kernelxing@tencent.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 4 Sep 2024 10:53:50 +0000 (11:53 +0100)]
Merge branch 'sparx5-fdma-part-one'
Daniel Machon says:
====================
net: microchip: add FDMA library and use it for Sparx5
This patch series is the first of a 2-part series, that adds a new
common FDMA library for Microchip switch chips Sparx5 and lan966x. These
chips share the same FDMA engine, and as such will benefit from a
common library with a common implementation. This also has the benefit
of removing a lot open-coded bookkeeping and duplicate code for the two
drivers.
Additionally, upstreaming efforts for a third chip, lan969x, will begin
in the near future. This chip will use the new library too.
In this first series, the FDMA library is introduced and used by the
Sparx5 switch driver.
###################
# Example of use: #
###################
- Initialize the rx and tx fdma structs with values for: number of
DCB's, number of DB's, channel ID, DB size (data buffer size), and
total size of the requested memory. Also provide two callbacks:
nextptr_cb() and dataptr_cb() for getting the nextptr and dataptr.
- Allocate memory using fdma_alloc_phys() or fdma_alloc_coherent().
- Initialize the DCB's with fdma_dcb_init().
- Add new DCB's with fdma_dcb_add().
- Free memory with fdma_free_phys() or fdma_free_coherent().
Patch #1: introduces library and selects it for Sparx5.
Patch #2: includes the fdma_api.h header and removes old symbols.
Patch #3: replaces old rx and tx variables with equivalent ones from the
fdma struct. Only the variables that can be changed without
breaking traffic is changed in this patch.
Patch #4: uses the library for allocation of rx buffers. This requires
quite a bit of refactoring in this single patch.
Patch #5: uses the library for adding DCB's in the rx path.
Patch #6: uses the library for freeing rx buffers.
Patch #7: uses the library helpers in the rx path.
Patch #8: uses the library for allocation of tx buffers. This requires
quite a bit of refactoring in this single patch.
Patch #9: uses the library for adding DCB's in the tx path.
Patch #10: uses the library helpers in the tx path.
Patch #11: ditches the existing linked list for storing buffer addresses,
and instead uses offsets into contiguous memory.
Patch #12: modifies existing rx and tx functions to be direction
independent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These direction specific functions can be ditched in favor of a single
function: sparx5_fdma_reload(), which retrieves the channel id from the
fdma struct instead.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:16 +0000 (16:54 +0200)]
net: sparx5: use contiguous memory for tx buffers
Currently, the driver uses a linked list for storing the tx buffer
addresses. This requires a good amount of extra bookkeeping code. Ditch
the linked list in favor of tx buffers being in the same contiguous
memory space as the DCB's and the DB's. The FDMA library has a helper
for this - so use that.
The tx buffer addresses are now retrieved as an offset into the FDMA
memory space.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:15 +0000 (16:54 +0200)]
net: sparx5: use library helper for freeing tx buffers
The library has the helper fdma_free_phys() for freeing physical FDMA
memory. Use it in the exit path.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:14 +0000 (16:54 +0200)]
net: sparx5: use FDMA library for adding DCB's in the tx path
Use the fdma_dcb_add() function to add DCB's in the tx path. This gets
rid of the open-coding of nextptr and dataptr handling and leaves it to
the library.
Also, make sure the fdma indexes are advanced using: fdma_dcb_advance(),
so that the correct nextptr and dataptr offsets are retrieved.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:13 +0000 (16:54 +0200)]
net: sparx5: use the FDMA library for allocation of tx buffers
Use the two functions: fdma_alloc_phys() and fdma_dcb_init() for tx
buffer allocation and use the new buffers throughout.
In order to replace the old buffers with the new ones, we have to do the
following refactoring:
- use fdma_alloc_phys() and fdma_dcb_init()
- replace the variables: tx->dma, tx->first_entry and tx->curr_entry
with the equivalents from the FDMA struct.
- replace uses of sparx5_db_hw and sparx5_tx_dcb_hw with fdma_db and
fdma_dcb.
- add sparx5_fdma_tx_dataptr_cb callback for obtaining the dataptr.
- Initialize FDMA struct values.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:12 +0000 (16:54 +0200)]
net: sparx5: use a few FDMA helpers in the rx path
The library provides helpers for a number of DCB and DB operations. Use
these in the rx path.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:11 +0000 (16:54 +0200)]
net: sparx5: use library helper for freeing rx buffers
The library has the helper fdma_free_phys() for freeing physical FDMA
memory. Use it in the exit path.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:10 +0000 (16:54 +0200)]
net: sparx5: use FDMA library for adding DCB's in the rx path
Use the fdma_dcb_add() function to add DCB's in the rx path. This gets
rid of the open-coding of nextptr and dataptr handling and leaves it to
the library.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:09 +0000 (16:54 +0200)]
net: sparx5: use the FDMA library for allocation of rx buffers
Use the two functions: fdma_alloc_phys() and fdma_dcb_init() for rx
buffer allocation and use the new buffers throughout.
In order to replace the old buffers with the new ones, we have to do the
following refactoring:
- use fdma_alloc_phys() and fdma_dcb_init()
- replace the variables: rx->dma, rx->dcb_entries and rx->last_entry
with the equivalents from the FDMA struct.
- replace uses of sparx5_db_hw and sparx5_rx_dcb_hw with fdma_db and
fdma_dcb.
- add sparx5_fdma_rx_dataptr_cb callback for obtaining the dataptr.
- Initialize FDMA struct values.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:08 +0000 (16:54 +0200)]
net: sparx5: replace a few variables with new equivalent ones
Replace the old rx and tx variables: channel_id, FDMA_DCB_MAX,
FDMA_RX_DCB_MAX_DBS, FDMA_TX_DCB_MAX_DBS, dcb_index and db_index with
the equivalents from the FDMA rx and tx structs. These variables are not
entangled in any buffer allocation and can therefore be replaced in
advance.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:07 +0000 (16:54 +0200)]
net: sparx5: use FDMA library symbols
Include and use the new FDMA header, which now provides the required
masks and bit offsets for operating on the DCB's and DB's.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon [Mon, 2 Sep 2024 14:54:06 +0000 (16:54 +0200)]
net: microchip: add FDMA library
Add new FDMA library for interacting with the FDMA engine on Microchip
Sparx5 and lan966x switch chips, in an effort to reduce duplicate code
and provide a common set of symbols and functions.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Reviewed-by: Jens Emil Schulz Østergaard <jensemil.schulzostergaard@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6b7c5b947c67 ("net: Add be2net driver.") declared be_pci_fnum_get()
and be_cmd_reset() but never implemented. And commit 9fa465c0ce0d ("be2net:
remove code duplication relating to Lancer reset sequence") removed
lancer_test_and_set_rdy_state() but leave declaration.
Commit 76a9e08e33ce ("be2net: cleanup wake-on-lan code") left behind
be_is_wol_supported() declaration.
Commit baaa08d148ac ("be2net: do not call be_set/get_fw_log_level() on
Skyhawk-R") removed be_get_fw_log_level() but leave declaration.
In general, calling dev_err_probe() after successful probe in case of
handling -EPROBE_DEFER error, will set deferred status on the device
already probed. This is however not a problem here now, because
dev_err_probe() in affected places is used for handling errors from
request_firmware(), which does not return -EPROBE_DEFER. Still usage of
dev_err_probe() in such case is not correct, because request_firmware()
could once return -EPROBE_DEFER.
Fixes: bf4d87f884fe ("net: alacritech: Switch to use dev_err_probe()") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240902163610.17028-1-krzysztof.kozlowski@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netlink: specs: nftables: allow decode of default firewalld ruleset
This update allows listing default firewalld ruleset on Fedora 40 via
tools/net/ynl/cli.py --spec \
Documentation/netlink/specs/nftables.yaml --dump getrule
Default ruleset uses fib, reject and objref expressions which were
missing.
Other missing expressions can be added later.
Improve decoding while at it:
- add bitwise, ct and lookup attributes
- wire up the quota expression
- translate raw verdict codes to a human reable name, e.g.
'code': 4294967293 becomes 'code': 'jump'.
v2: forgot fib addrtype in enum list (Donald Hunter)
====================
mptcp: MIB counters for MPJ TX + misc improvements
Recently, a few issues have been discovered around the creation of
additional subflows. Without these counters, it was difficult to point
out the reason why some subflows were not created as expected.
In patch 3, all error paths from __mptcp_subflow_connect() are covered,
except the one related to the 'fully established mode', because it can
only happen with the userspace PM, which will propagate the error to the
userspace in this case (ENOTCONN).
These new counters are also verified in the MPTCP Join selftest in patch
6.
While at it, a few other patches are improving the MPTCP path-manager
code ...
- Patch 1: 'flush' related helpers are renamed to avoid confusions
- Patch 2: directly pass known ID and flags to create a new subflow,
i/o getting them later by iterating over all endpoints again
... and the MPJoin selftests:
- Patch 4: reduce the number of positional parameters
- Patch 5: only one line for the 'join' checks, instead of 3
- Patch 7: more explicit check names, instead of sometimes too cryptic
ones: rtx, ptx, ftx, ctx, fclzrx, sum
- Patch 8: specify client/server instead of 'invert' for some checks
not suggesting one specific direction
- Patch 9: mute errors of mptcp_connect when ran in the background
- Patch 10: simplify checksum_tests by using a for-loop
- Patch 11: remove 'define' re-definitions
====================
'MPTCP_PM_NAME' is defined in 'linux/mptcp_pm.h', included in
'linux/mptcp.h', no need to re-define it.
'MPTCP_PM_EVENTS' is not defined in 'linux/mptcp.h', but
'MPTCP_PM_EV_GRP_NAME' is, with the same value. We can then use the
latter, and drop the other one.
selftests: mptcp: join: mute errors when ran in the background
The test is supposed to be killed before the end, which will likely
cause "Connection reset by peer" errors. It is confusing, especially
because in case of real transfer errors, the test will not be marked as
failed. But that's OK, there are many other tests checking that.
selftests: mptcp: join: specify host being checked
Instead of displaying 'invert' when looking at some events like MP_FAIL,
MP_FASTCLOSE, MP_RESET, RM_ADDR, which is a bit vague because they are
not traditionnaly sent from one side, the host being checked is now
printed.
For the ADD_ADDR, only display the host when it is the client sending
it, which is more unusual.
Also before, the 'invert' message was printed after a few checks, but it
was not clear which ones exactly.
selftests: mptcp: join: validate MPJ SYN TX MIB counters
A few new MPJoinSynTx MIB counters have been added in a previous commit.
They are being validated here in mptcp_join.sh selftest, each time the
number of received MPJ are checked.
Most of the time, the number of sent SYN+MPJ is the same as the received
ones. But sometimes, there are more, because there are dropped, or there
are errors.
While at it, the "no MPC reuse with single endpoint" subtest has been
modified to force a bind() error.
Most tests are checking if the expected number of SYN/SYN+ACK/ACK JOINs
have been received, each of them on one line.
More Join related tests are going to be checked soon, no need to add 5
new lines per test in case of success, just one is enough. In case of
issue, the errors will still be reported like before.
Recently, a few issues have been discovered around the creation of
additional subflows. Without these counters, it was difficult to point
out the reason why some subflows were not created as expected.
These counters should have been added earlier, because there is no other
simple ways to extract such information from the kernel, and understand
why subflows have not been created.
While at it, some pr_debug() have been added, just in case the errno
needs to be printed.
__mptcp_subflow_connect() is currently called from the path-managers,
which have all the required information to create subflows. No need to
call the PM again to re-iterate over the list of entries with RCU lock
to get more info.
Instead, it is possible to pass a mptcp_pm_addr_entry structure, instead
of a mptcp_addr_info one. The former contains the ifindex and the flags
that are required when creating the new subflow.
This is a partial revert of commit ee285257a9c1 ("mptcp: drop flags and
ifindex arguments").
While at it, the local ID can also be set if it is known and 0, to avoid
having to set it in the 'rebuild_header' hook, which will cause a new
iteration of the endpoint entries.
Rename all the helpers specific to the flushing operations to make it
clear that the intention is to flush all created subflows, and remove
all announced addresses, not just a specific selection.
That way, it is easier to understand why the id_avail_bitmap and
local_addr_used are reset at the end.
Jakub Kicinski [Tue, 3 Sep 2024 22:18:45 +0000 (15:18 -0700)]
Merge branch 'rx-software-timestamp-for-all'
Gal Pressman says:
====================
RX software timestamp for all
All devices support SOF_TIMESTAMPING_RX_SOFTWARE by virtue of
net_timestamp_check() being called in the device independent code.
Following Willem's suggestion [1], make it so drivers do not have to
handle SOF_TIMESTAMPING_RX_SOFTWARE and SOF_TIMESTAMPING_SOFTWARE, nor
setting of the PHC index to -1.
All drivers will now report RX software timestamp as supported.
The series is limited to 15 patches, I will submit other drivers in
subsequent submissions.
Gal Pressman [Sun, 1 Sep 2024 11:28:03 +0000 (14:28 +0300)]
net: mvpp2: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Marcin Wojtas <marcin.s.wojtas@gmail.com> Link: https://patch.msgid.link/20240901112803.212753-16-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Sun, 1 Sep 2024 11:28:02 +0000 (14:28 +0300)]
octeontx2-pf: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Gal Pressman [Sun, 1 Sep 2024 11:28:01 +0000 (14:28 +0300)]
gianfar: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20240901112803.212753-14-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Sun, 1 Sep 2024 11:28:00 +0000 (14:28 +0300)]
net: enetc: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Gal Pressman [Sun, 1 Sep 2024 11:27:59 +0000 (14:27 +0300)]
net: fec: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Gal Pressman [Sun, 1 Sep 2024 11:27:58 +0000 (14:27 +0300)]
net: hns3: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Gal Pressman [Sun, 1 Sep 2024 11:27:57 +0000 (14:27 +0300)]
net: ethernet: rtsn: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Gal Pressman [Sun, 1 Sep 2024 11:27:56 +0000 (14:27 +0300)]
net: renesas: rswitch: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Gal Pressman [Sun, 1 Sep 2024 11:27:55 +0000 (14:27 +0300)]
ravb: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Gal Pressman [Sun, 1 Sep 2024 11:27:54 +0000 (14:27 +0300)]
ionic: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Link: https://patch.msgid.link/20240901112803.212753-7-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Sun, 1 Sep 2024 11:27:53 +0000 (14:27 +0300)]
tsnep: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com> Link: https://patch.msgid.link/20240901112803.212753-6-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Sun, 1 Sep 2024 11:27:52 +0000 (14:27 +0300)]
can: peak_usb: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://patch.msgid.link/20240901112803.212753-5-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Sun, 1 Sep 2024 11:27:51 +0000 (14:27 +0300)]
can: peak_canfd: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://patch.msgid.link/20240901112803.212753-4-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Sun, 1 Sep 2024 11:27:50 +0000 (14:27 +0300)]
can: dev: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://patch.msgid.link/20240901112803.212753-3-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Sun, 1 Sep 2024 11:27:49 +0000 (14:27 +0300)]
ethtool: RX software timestamp for all
All devices support SOF_TIMESTAMPING_RX_SOFTWARE by virtue of
net_timestamp_check() being called in the device independent code.
Move the responsibility of reporting SOF_TIMESTAMPING_RX_SOFTWARE and
SOF_TIMESTAMPING_SOFTWARE, and setting PHC index to -1 to the core.
Device drivers no longer need to use them.
Jakub Kicinski [Tue, 3 Sep 2024 19:50:02 +0000 (12:50 -0700)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-08-30 (igc, e1000e, i40e)
This series contains updates to igc, e1000e, and i40 drivers.
Kurt Kanzenbach adds support for MQPRIO offloads and stops unintended,
excess interrupts on igc.
Sasha adds reporting of EEE (Energy Efficient Ethernet) ability and
moves a register define to a better suited file for igc.
Vitaly stops reporting errors on shutdown and suspend as they are not
fatal for e1000e.
Alex adds reporting of EEE to i40e.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
i40e: Add Energy Efficient Ethernet ability for X710 Base-T/KR/KX cards
e1000e: avoid failing the system during pm_suspend
igc: Move the MULTI GBT AN Control Register to _regs file
igc: Add Energy Efficient Ethernet ability
igc: Get rid of spurious interrupts
igc: Add MQPRIO offload support
====================
Jakub Kicinski [Tue, 3 Sep 2024 18:59:44 +0000 (11:59 -0700)]
Merge tag 'ieee802154-for-net-2024-09-01' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2024-09-01
Simon Horman catched two typos in our headers. No functional change.
* tag 'ieee802154-for-net-2024-09-01' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
ieee802154: Correct spelling in nl802154.h
mac802154: Correct spelling in mac802154.h
====================
Justin Iurman [Fri, 30 Aug 2024 19:19:19 +0000 (21:19 +0200)]
ioam6: improve checks on user data
This patch improves two checks on user data.
The first one prevents bit 23 from being set, as specified by RFC 9197
(Sec 4.4.1):
Bit 23 Reserved; MUST be set to zero upon transmission and be
ignored upon receipt. This bit is reserved to allow for
future extensions of the IOAM Trace-Type bit field.
The second one checks that the tunnel destination address !=
IPV6_ADDR_ANY, just like we already do for the tunnel source address.
Marek Vasut [Wed, 21 Aug 2024 18:36:54 +0000 (20:36 +0200)]
wifi: wilc1000: Re-enable RTC clock on resume
The wilc_sdio_suspend() does clk_disable_unprepare() on rtc_clk clock,
make sure wilc_sdio_resume() does matching clk_prepare_enable(), else
any suspend/resume cycle leads to clock disable/enable imbalance. Fix
the imbalance.
Marek Vasut [Wed, 21 Aug 2024 18:36:03 +0000 (20:36 +0200)]
wifi: wilc1000: Do not operate uninitialized hardware during suspend/resume
In case the hardware is not initialized, do not operate it during
suspend/resume cycle, the hardware is already off so there is no
reason to access it.
In fact, wilc_sdio_enable_interrupt() in the resume callback does
interfere with the same call when initializing the hardware after
resume and makes such initialization after resume fail. Fix this
by not operating uninitialized hardware during suspend/resume.
Frank Li [Tue, 20 Aug 2024 14:21:42 +0000 (10:21 -0400)]
dt-bindings: net: wireless: convert marvel-8xxx.txt to yaml format
Convert binding doc marvel-8xxx.txt to yaml format.
Additional change:
- Remove marvell,caldata_00_txpwrlimit_2g_cfg_set in example.
- Remove mmc related property in example.
- Add wakeup-source property.
- Remove vmmc-supply and mmc-pwrseq.
Fix below warning:
arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dtb: /soc@0/bus@30800000/mmc@30b40000/wifi@1:
failed to match any schema with compatible: ['marvell,sd8997']
projects / users / jedix / linux-maple.git / log