As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") Reported-by: Rafael Richter <Rafael.Richter@gin.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Daniel Klauer <daniel.klauer@gin.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 803.2ad mode enables a participating port, it should update
the slave-array. I have observed that the member links are participating
and are part of the active aggregator while the traffic is egressing via
only one member link (in a case where two links are participating). Via
kprobes I discovered that slave-arr has only one link added while
the other participating link wasn't part of the slave-arr.
I couldn't see what caused that situation but the simple code-walk
through provided me hints that the enable_port wasn't always associated
with the slave-array update.
Fixes: ee6377147409 ("bonding: Simplify the xmit function for modes that use xmit_hash") Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting the output of a GPIO to 1 using gpiod_set_value(), followed by
reading the same GPIO using gpiod_get_value(), will currently yield an
incorrect result.
This is because the SiFive GPIO device stores the output values in reg_set,
not reg_dat.
Supply the flag BGPIOF_READ_OUTPUT_REG_SET to bgpio_init() so that the
generic driver reads the correct register.
Commit 4a9af6cac050 ("ACPI: EC: Rework flushing of EC work while
suspended to idle") made acpi_ec_dispatch_gpe() check
pm_wakeup_pending(), but that is before canceling the SCI wakeup,
so pm_wakeup_pending() is always true. This causes the loop in
acpi_ec_dispatch_gpe() to always terminate after one iteration which
may not be correct.
Address this issue by canceling the SCI wakeup earlier, from
acpi_ec_dispatch_gpe() itself.
Fixes: 4a9af6cac050 ("ACPI: EC: Rework flushing of EC work while suspended to idle") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function panel_simple_probe() the pointer panel->desc is
assigned to the passed pointer desc. If function panel_dpi_probe()
is called panel->desc will be updated, but further on only desc
will be evaluated. So update the desc pointer to be able to use
the data from the function panel_dpi_probe().
Fixes: 4a1d0dbc8332 ("drm/panel: simple: add panel-dpi support") Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: Marek Vasut <marex@denx.de> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch>
To: dri-devel@lists.freedesktop.org Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Marek Vasut <marex@denx.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220201110153.3479-1-cniedermaier@dh-electronics.com Signed-off-by: Sasha Levin <sashal@kernel.org>
From 4.17 onwards the ixgbevf driver uses build_skb() to build an skb
around new data in the page buffer shared with the ixgbe PF.
This uses either a 2K or 3K buffer, and offsets the DMA mapping by
NET_SKB_PAD + NET_IP_ALIGN. When using a smaller buffer RXDCTL is set to
ensure the PF does not write a full 2K bytes into the buffer, which is
actually 2K minus the offset.
However on the 82599 virtual function, the RXDCTL mechanism is not
available. The driver attempts to work around this by using the SET_LPE
mailbox method to lower the maximm frame size, but the ixgbe PF driver
ignores this in order to keep the PF and all VFs in sync[0].
This means the PF will write up to the full 2K set in SRRCTL, causing it
to write NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the buffer.
With 4K pages split into two buffers, this means it either writes
NET_SKB_PAD + NET_IP_ALIGN bytes past the first buffer (and into the
second), or NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the DMA
mapping.
Avoid this by only enabling build_skb when using "large" buffers (3K).
These are placed in each half of an order-1 page, preventing the PF from
writing past the end of the mapping.
[0]: Technically it only ever raises the max frame size, see
ixgbe_set_vf_lpe() in ixgbe_sriov.c
Fixes: f15c5ba5b6cd ("ixgbevf: add support for using order 1 pages to receive large frames") Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the copy back to userland fails for the FASTRPC_IOCTL_ALLOC_DMA_BUFF
ioctl(), we shouldn't assume that 'buf->dmabuf' is still valid. In fact,
dma_buf_fd() called fd_install() before, i.e. "consumed" one reference,
leaving us with none.
Calling dma_buf_put() will therefore put a reference we no longer own,
leading to a valid file descritor table entry for an already released
'file' object which is a straight use-after-free.
Simply avoid calling dma_buf_put() and rely on the process exit code to
do the necessary cleanup, if needed, i.e. if the file descriptor is
still valid.
Fixes: 6cffd79504ce ("misc: fastrpc: Add support for dmabuf exporter") Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Mathias Krause <minipli@grsecurity.net> Link: https://lore.kernel.org/r/20220127130218.809261-1-minipli@grsecurity.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
If the parent GPIO controller is a sleeping controller (e.g. a GPIO
controller connected to I2C), getting or setting a GPIO triggers a
might_sleep() warning. This happens because the GPIO Aggregator takes
the can_sleep flag into account only for its internal locking, not for
calling into the parent GPIO controller.
Fix this by using the gpiod_[gs]et*_cansleep() APIs when calling into a
sleeping GPIO controller.
Consider a case where ffs_func_eps_disable is called from
ffs_func_disable as part of composition switch and at the
same time ffs_epfile_release get called from userspace.
ffs_epfile_release will free up the read buffer and call
ffs_data_closed which in turn destroys ffs->epfiles and
mark it as NULL. While this was happening the driver has
already initialized the local epfile in ffs_func_eps_disable
which is now freed and waiting to acquire the spinlock. Once
spinlock is acquired the driver proceeds with the stale value
of epfile and tries to free the already freed read buffer
causing use-after-free.
Fix this races by taking epfiles local copy & assigning it under
spinlock and if epfiles(local) is null then update it in ffs->epfiles
then finally destroy it.
Extending the scope further from the race, protecting the ep related
structures, and concurrent accesses.
The correct property name is 'assigned-clock-parents', not
'assigned-clocks-parents'. Though if the platform works with the typo, one
has to wonder if the property is even needed.
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea00314 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8b-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8b-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml bindings.
Fixes: b02d6e73f5fc96 ("ARM: dts: meson8b: use stable UART bindings with correct gate clock") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211227180026.4068352-4-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml schema.
Fixes: 6ca77502050eff ("ARM: dts: meson8: use stable UART bindings with correct gate clock") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211227180026.4068352-3-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The dt-bindings for the UART controller only allow the following values
for Meson6 SoCs:
- "amlogic,meson6-uart", "amlogic,meson-ao-uart"
- "amlogic,meson6-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Commit e428e250fde6 ("ARM: dts: Configure system timers for omap3")
caused a timer regression for beagleboard revision c where the system
clockevent stops working if omap3isp module is unloaded.
Turns out we still have beagleboard revisions a-b4 capacitor c70 quirks
applied that limit the usable timers for no good reason. This also affects
the power management as we use the system clock instead of the 32k clock
source.
Let's fix the issue by adding a new omap3-beagle-ab4.dts for the old timer
quirks. This allows us to remove the timer quirks for later beagleboard
revisions. We also need to update the related timer quirk check for the
correct compatible property.
Fixes: e428e250fde6 ("ARM: dts: Configure system timers for omap3") Cc: linux-kernel@vger.kernel.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rob Herring <robh+dt@kernel.org> Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bits 5:6 (i.e., shift 5, mask 0x3) are correct for RK3399, according to
the TRM.
There are a few other small differences between the 3288 and 3368
definitions that were swapped in commit 7707f7227f09. I reviewed them to
the best of my ability according to the RK3399 TRM and fixed them up.
This fixes IOMMU issues (and display errors) when testing with BG24
color formats.
Fixes: 7707f7227f09 ("drm/rockchip: Add support for afbc") Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220119161104.1.I1d01436bef35165a8cdfe9308789c0badb5ff46a@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE") Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original version of the IORT PMCG definition had an oversight
wherein there was no way to describe the second register page for an
implementation using the recommended RELOC_CTRS feature. Although the
spec was fixed, and the final patches merged to ACPICA and Linux written
against the new version, it seems that some old firmware based on the
original revision has survived and turned up in the wild.
Add a check for the original PMCG definition, and avoid filling in the
second memory resource with nonsense if so. Otherwise it is likely that
something horrible will happen when the PMCG driver attempts to probe.
Reported-by: Michael Petlan <mpetlan@redhat.com> Fixes: 24e516049360 ("ACPI/IORT: Add support for PMCG") Cc: <stable@vger.kernel.org> # 5.2.x Signed-off-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Link: https://lore.kernel.org/r/75628ae41c257fb73588f7bf1c4459160e04be2b.1643916258.git.robin.murphy@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AER is not backed by a real request, hence we should not incorrectly
assume that when failing to send a nvme command, it is a normal request
but rather check if this is an aer and if so complete the aer (similar
to the normal completion path).
Cc: stable@vger.kernel.org Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SocFPGA machine since commit b3ca9888f35f ("reset: socfpga: add an
early reset driver for SoCFPGA") uses reset controller, so it should
select RESET_CONTROLLER explicitly. Selecting ARCH_HAS_RESET_CONTROLLER
is not enough because it affects only default choice still allowing a
non-buildable configuration:
/usr/bin/arm-linux-gnueabi-ld: arch/arm/mach-socfpga/socfpga.o: in function `socfpga_init_irq':
arch/arm/mach-socfpga/socfpga.c:56: undefined reference to `socfpga_reset_init'
Reported-by: kernel test robot <lkp@intel.com> Cc: <stable@vger.kernel.org> Fixes: b3ca9888f35f ("reset: socfpga: add an early reset driver for SoCFPGA") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, SD card fails to mount due to the following pinctrl error:
[ 11.170000] imx23-pinctrl 80018000.pinctrl: pin SSP1_DETECT already requested by 80018000.pinctrl; cannot claim for 80010000.spi
[ 11.180000] imx23-pinctrl 80018000.pinctrl: pin-65 (80010000.spi) status -22
[ 11.190000] imx23-pinctrl 80018000.pinctrl: could not request pin 65 (SSP1_DETECT) from group mmc0-pins-fixup.0 on device 80018000.pinctrl
[ 11.200000] mxs-mmc 80010000.spi: Error applying setting, reverse things back
Fix it by removing the MX23_PAD_SSP1_DETECT pin from the hog group as it
is already been used by the mmc0-pins-fixup pinctrl group.
With this change the rootfs can be mounted and the imx23-evk board can
boot successfully.
From version 2.38, binutils default to ISA spec version 20191213. This
means that the csr read/write (csrr*/csrw*) instructions and fence.i
instruction has separated from the `I` extension, become two standalone
extensions: Zicsr and Zifencei. As the kernel uses those instruction,
this causes the following build failure:
Set vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS, a.k.a. the pending single-step
breakpoint flag, when re-injecting a #DB with RFLAGS.TF=1, and STI or
MOVSS blocking is active. Setting the flag is necessary to make VM-Entry
consistency checks happy, as VMX has an invariant that if RFLAGS.TF is
set and STI/MOVSS blocking is true, then the previous instruction must
have been STI or MOV/POP, and therefore a single-step #DB must be pending
since the RFLAGS.TF cannot have been set by the previous instruction,
i.e. the one instruction delay after setting RFLAGS.TF must have already
expired.
Normally, the CPU sets vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS appropriately
when recording guest state as part of a VM-Exit, but #DB VM-Exits
intentionally do not treat the #DB as "guest state" as interception of
the #DB effectively makes the #DB host-owned, thus KVM needs to manually
set PENDING_DBG.BS when forwarding/re-injecting the #DB to the guest.
Note, although this bug can be triggered by guest userspace, doing so
requires IOPL=3, and guest userspace running with IOPL=3 has full access
to all I/O ports (from the guest's perspective) and can crash/reboot the
guest any number of ways. IOPL=3 is required because STI blocking kicks
in if and only if RFLAGS.IF is toggled 0=>1, and if CPL>IOPL, STI either
takes a #GP or modifies RFLAGS.VIF, not RFLAGS.IF.
MOVSS blocking can be initiated by userspace, but can be coincident with
a #DB if and only if DR7.GD=1 (General Detect enabled) and a MOV DR is
executed in the MOVSS shadow. MOV DR #GPs at CPL>0, thus MOVSS blocking
is problematic only for CPL0 (and only if the guest is crazy enough to
access a DR in a MOVSS shadow). All other sources of #DBs are either
suppressed by MOVSS blocking (single-step, code fetch, data, and I/O),
are mutually exclusive with MOVSS blocking (T-bit task switch), or are
already handled by KVM (ICEBP, a.k.a. INT1).
This bug was originally found by running tests[1] created for XSA-308[2].
Note that Xen's userspace test emits ICEBP in the MOVSS shadow, which is
presumably why the Xen bug was deemed to be an exploitable DOS from guest
userspace. KVM already handles ICEBP by skipping the ICEBP instruction
and thus clears MOVSS blocking as a side effect of its "emulation".
Inject a #GP instead of synthesizing triple fault to try to avoid killing
the guest if emulation of an SEV guest fails due to encountering the SMAP
erratum. The injected #GP may still be fatal to the guest, e.g. if the
userspace process is providing critical functionality, but KVM should
make every attempt to keep the guest alive.
Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-10-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to MSR_IA32_VMX_EXIT_CTLS/MSR_IA32_VMX_TRUE_EXIT_CTLS,
MSR_IA32_VMX_ENTRY_CTLS/MSR_IA32_VMX_TRUE_ENTRY_CTLS pair,
MSR_IA32_VMX_TRUE_PINBASED_CTLS needs to be filtered the same way
MSR_IA32_VMX_PINBASED_CTLS is currently filtered as guests may solely rely
on 'true' MSR data.
Note, none of the currently existing Windows/Hyper-V versions are known
to stumble upon the unfiltered MSR_IA32_VMX_TRUE_PINBASED_CTLS, the change
is aimed at making the filtering future proof.
Enlightened VMCS v1 doesn't have VMX_PREEMPTION_TIMER_VALUE field,
PIN_BASED_VMX_PREEMPTION_TIMER is also filtered out already so it makes
sense to filter out VM_EXIT_SAVE_VMX_PREEMPTION_TIMER too.
Note, none of the currently existing Windows/Hyper-V versions are known
to enable 'save VMX-preemption timer value' when eVMCS is in use, the
change is aimed at making the filtering future proof.
Since kvm_unregister_irq_ack_notifier() does synchronize_srcu(&kvm->irq_srcu),
kvm->irq_ack_notifier_list is protected by kvm->irq_srcu. In fact,
kvm->irq_srcu SRCU read lock is held in kvm_notify_acked_irq(), making it
a false positive warning. So use hlist_for_each_entry_srcu() instead of
hlist_for_each_entry_rcu().
Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Hou Wenlong <houwenlong93@linux.alibaba.com>
Message-Id: <f98bac4f5052bad2c26df9ad50f7019e40434512.1643265976.git.houwenlong.hwl@antgroup.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using per-process mode and event inheritance is set to true,
forked processes will create a new perf events via inherit_event() ->
perf_event_alloc(). But these events will not have ring buffers
assigned to them. Any call to wakeup will be dropped if it's called on
an event with no ring buffer assigned because that's the object that
holds the wakeup list.
If the child event is disabled due to a call to
perf_aux_output_begin() or perf_aux_output_end(), the wakeup is
dropped leaving userspace hanging forever on the poll.
Normally the event is explicitly re-enabled by userspace after it
wakes up to read the aux data, but in this case it does not get woken
up so the event remains disabled.
This can be reproduced when using Arm SPE and 'stress' which forks once
before running the workload. By looking at the list of aux buffers read,
it's apparent that they stop after the fork:
perf record -e arm_spe// -vvv -- stress -c 1
With this patch applied they continue to be printed. This behaviour
doesn't happen when using systemwide or per-cpu mode.
Reported-by: Ruben Ayrapetyan <Ruben.Ayrapetyan@arm.com> Signed-off-by: James Clark <james.clark@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20211206113840.130802-2-james.clark@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
It is an unused wrapper forcing kmalloc allocation for registering
nosave regions. Also, rename __register_nosave_region() to
register_nosave_region() now that there is no need for disambiguation.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In myrs_detect(), cs->disable_intr is NULL when privdata->hw_init() fails
with non-zero. In this case, myrs_cleanup(cs) will call a NULL ptr and
crash the kernel.
This event is raised when link is lost as specified in UFSHCI spec and that
means communication is not possible. Thus initializing UFS interface needs
to be done.
Make UFS driver considers Link Lost as fatal in the INT_FATAL_ERRORS
mask. This will trigger a host reset whenever a link lost interrupt occurs.
According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.
However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.
Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.
The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.
Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
iscsit_tpg_check_network_portal() has nested for_each loops and is supposed
to return true when a match is found. However, the tpg loop will still
continue after existing the tpg_np loop. If this tpg_np is not the last the
match value will be changed.
Break the outer loop after finding a match and make sure the np under each
tpg is unique.
Link: https://lore.kernel.org/r/20220111054742.19582-1-mingzhe.zou@easystack.cn Signed-off-by: ZouMingzhe <mingzhe.zou@easystack.cn> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding a tc rule with a qdisc kind that is not supported or not
compiled into the kernel, the kernel emits the following error: "Error:
Specified qdisc not found.". Found via tdc testing when ETS qdisc was not
compiled in and it was not obvious right away what the message meant
without looking at the kernel code.
Change the error message to be more explicit and say the qdisc kind is
unknown.
Signed-off-by: Victor Nogueira <victor@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some hypervisors support Arch LBR, but without the LBR XSAVE support.
The current Arch LBR init code prints a warning when the xsave size (0) is
unexpected. Avoid printing the warning for the "no LBR XSAVE" case.
An fs_location attribute returns a string that can be ipv4, ipv6,
or DNS name. An ip location can have a port appended to it and if
no port is present a default port needs to be set. If rpc_pton()
fails to parse, try calling rpc_uaddr2socaddr() that can convert
an universal address.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When decode_devicenotify_args() exits with no entries, we need to
ensure that the struct cb_devicenotifyargs is initialised to
{ 0, NULL } in order to avoid problems in
nfs4_callback_devicenotify().
When the bitmask of the attributes doesn't include the security label,
don't bother printing it. Since the label might not be null terminated,
adjust the printing format accordingly.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the nfs_access_get_cached family of functions report a
'struct nfs_access_entry' as the result, with both .mask and .cred set.
However the .cred is never used. This is probably good and there is no
guarantee that it won't be freed before use.
Change to only report the 'mask' - as this is all that is used or needed.
In Mesa, dev_info.gart_page_size is used for alignment and it was
set to AMDGPU_GPU_PAGE_SIZE(4KB). However, the page table of AMDGPU
driver requires an alignment on CPU pages. So, for non-4KB page system,
gart_page_size should be max_t(u32, PAGE_SIZE, AMDGPU_GPU_PAGE_SIZE).
Signed-off-by: Rui Wang <wangr@lemote.com> Signed-off-by: Huacai Chen <chenhc@lemote.com> Link: https://github.com/loongson-community/linux-stable/commit/caa9c0a1
[Xi: rebased for drm-next, use max_t for checkpatch,
and reworded commit message.] Signed-off-by: Xi Ruoyao <xry111@mengyan1223.wang> BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1549 Tested-by: Dan Horák <dan@danny.cz> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Salvatore Bonaccorso: Backport to 5.10.y which does not contain a5a52a43eac0 ("drm/amd/amdgpu/amdgpu_kms: Remove 'struct
drm_amdgpu_info_device dev_info' from the stack") which removes dev_info
from the stack and places it on the heap.] Tested-by: Timothy Pearson <tpearson@raptorengineering.com> Signed-off-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that a client cannot specify a WRITE range that falls in a
byte range outside what the kernel's internal types (such as loff_t,
which is signed) can represent. The kiocb iterators, invoked in
nfsd_vfs_write(), should properly limit write operations to within
the underlying file system's s_maxbytes.
Cc: stable@vger.kernel.org Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some long forgotten reason, the nfs_client cl_flags field is
initialised in nfs_get_client() instead of being initialised at
allocation time. This quirk was harmless until we moved the call to
nfs_create_rpc_client().
Fixes: dd99e9f98fbf ("NFSv4: Initialise connection to the server in nfs4_alloc_client()") Cc: stable@vger.kernel.org # 4.8.x Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting up autonegotiation for 88E1118R and compatible PHYs,
a software reset of PHY is issued before setting up polarity.
This is incorrect as changes of MDI Crossover Mode bits are
disruptive to the normal operation and must be followed by a
software reset to take effect. Let's patch m88e1118_config_aneg()
to fix the issue mentioned before by invoking software reset
of the PHY just after setting up MDI-x polarity.
Fixes: 605f196efbf8 ("phy: Add support for Marvell 88E1118 PHY") Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Cc: stable@vger.kernel.org Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org Fixes: d6ab93364734 ("net: phy: marvell: Avoid unnecessary soft reset") Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving a CAN frame the current code logic does not consider
concurrently receiving processes which do not show up in real world
usage.
Ziyang Xuan writes:
The following syz problem is one of the scenarios. so->rx.len is
changed by isotp_rcv_ff() during isotp_rcv_cf(), so->rx.len equals
0 before alloc_skb() and equals 4096 after alloc_skb(). That will
trigger skb_over_panic() in skb_put().
Therefore we make sure the state changes and data structures stay
consistent at CAN frame reception time by adding a spin_lock in
isotp_rcv(). This fixes the issue reported by syzkaller but does not
affect real world operation.
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
And since the sdhci_setup_host() has already checked the return value of
the enable_dma, we need not check it in sdhci_resume_host() again.
Commit c2426d2ad5027 ("ima: added support for new kernel cmdline parameter
ima_template_fmt") introduced an additional check on the ima_template
variable to avoid multiple template selection.
Unfortunately, ima_template could be also set by the setup function of the
ima_hash= parameter, when it calls ima_template_desc_current(). This causes
attempts to choose a new template with ima_template= or with
ima_template_fmt=, after ima_hash=, to be ignored.
Achieve the goal of the commit mentioned with the new static variable
template_setup_done, so that template selection requests after ima_hash=
are not ignored.
Finally, call ima_init_template_list(), if not already done, to initialize
the list of templates before lookup_template_desc() is called.
Reported-by: Guo Zihua <guozihua@huawei.com> Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Cc: stable@vger.kernel.org Fixes: c2426d2ad5027 ("ima: added support for new kernel cmdline parameter ima_template_fmt") Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
audit_log_start() returns audit_buffer pointer on success or NULL on
error, so it is better to check the return value of it.
Fixes: 3323eec921ef ("integrity: IMA as an integrity service provider") Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com> Cc: <stable@vger.kernel.org> Reviewed-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.
This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.
tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16. To
avert any risk of bit overflow, we add an extra sanity check for this in
that function. We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer. This potential problem was identified by Eric Dumazet.
This fixes CVE-2022-0435
Reported-by: Samuel Page <samuel.page@appgate.com> Reported-by: Eric Dumazet <edumazet@google.com> Fixes: 35c55c9877f8 ("tipc: add neighbor monitoring framework") Signed-off-by: Jon Maloy <jmaloy@redhat.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Samuel Page <samuel.page@appgate.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The soft dependency on cryptomgr is only needed in algapi because
if algapi isn't present then no algorithms can be loaded. This
also fixes the case where api is built-in but algapi is built as
a module as the soft dependency would otherwise get lost.
Fixes: 8ab23d547f65 ("crypto: api - Add softdep on cryptomgr") Reported-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refuse SIDA memops on guests which are not protected.
For normal guests, the secure instruction data address designation,
which determines the location we access, is not under control of KVM.
Fixes: 19e122776886 (KVM: S390: protvirt: Introduce instruction data area bounce buffer) Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com> Cc: stable@vger.kernel.org Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that the mmc host structure could be accessed after it
was freed in moxart_remove(), so fix this by saving the base register of
the device and using it instead of the pointer dereference.
Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn> Cc: Xin Xiong <xiongx18@fudan.edu.cn> Cc: Xin Tan <tanxin.ctf@gmail.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Yang Li <yang.lee@linux.alibaba.com> Cc: linux-mmc@vger.kernel.org Cc: stable <stable@vger.kernel.org> Reported-by: whitehat002 <hackyzh002@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was found that a "suspicious RCU usage" lockdep warning was issued
with the rcu_read_lock() call in update_sibling_cpumasks(). It is
because the update_cpumasks_hier() function may sleep. So we have
to release the RCU lock, call update_cpumasks_hier() and reacquire
it afterward.
Also add a percpu_rwsem_assert_held() in update_sibling_cpumasks()
instead of stating that in the comment.
Fixes: 4716909cc5c5 ("cpuset: Track cpusets that use parent's effective_cpus") Signed-off-by: Waiman Long <longman@redhat.com> Tested-by: Phil Auld <pauld@redhat.com> Reviewed-by: Phil Auld <pauld@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running "./check -I 200 generic/475" it sometimes gives below
kernel BUG(). Ideally we should not call ext4_write_inline_data() if
ext4_create_inline_data() has failed.
<log snip>
[73131.453234] kernel BUG at fs/ext4/inline.c:223!
This patch handles the error and prints out a emergency msg saying potential
data loss for the given inode (since we couldn't restore the original
inline_data due to some previous error).
[ 9571.070313] EXT4-fs (dm-0): error restoring inline_data for inode -- potential data loss! (inode 1703982, error -30)
For now in ext4_mb_new_blocks_simple, if we found a block which
should be excluded then will switch to next group, this may
probably cause 'group' run out of range.
Change to check next block in the same group when get a block should
be excluded. Also change the search range to EXT4_CLUSTERS_PER_GROUP
and add error checking.
During fast commit replay procedure, we clear inode blocks bitmap in
ext4_ext_clear_bb(), this may cause ext4_mb_new_blocks_simple() allocate
blocks still in use.
Make ext4_fc_record_regions() also record physical disk regions used by
inodes during replay procedure. Then ext4_mb_new_blocks_simple() can
excludes these blocks in use.
The driver overrides error codes returned by platform_get_irq_optional()
to -EINVAL for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
Kyle reported that rr[0] has started to malfunction on Comet Lake and
later CPUs due to EFI starting to make use of CPL3 [1] and the PMU
event filtering not distinguishing between regular CPL3 and SMM CPL3.
Since this is a privilege violation, default disable SMM visibility
where possible.
Administrators wanting to observe SMM cycles can easily change this
using the sysfs attribute while regular users don't have access to
this file.
[0] https://rr-project.org/
[1] See the Intel white paper "Trustworthy SMM on the Intel vPro Platform"
at https://bugzilla.kernel.org/attachment.cgi?id=300300, particularly the
end of page 5.
Reported-by: Kyle Huey <me@kylehuey.com> Suggested-by: Andrew Cooper <Andrew.Cooper3@citrix.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@kernel.org Link: https://lkml.kernel.org/r/YfKChjX61OW4CkYm@hirez.programming.kicks-ass.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check for !buf->single before calling pt_buffer_region_size in a
place where a missing check can cause a kernel crash.
Fixes a bug introduced by commit 670638477aed ("perf/x86/intel/pt:
Opportunistically use single range output mode"), which added a
support for PT single-range output mode. Since that commit if a PT
stop filter range is hit while tracing, the kernel will crash because
of a null pointer dereference in pt_handle_status due to calling
pt_buffer_region_size without a ToPA configured.
The commit which introduced single-range mode guarded almost all uses of
the ToPA buffer variables with checks of the buf->single variable, but
missed the case where tracing was stopped by the PT hardware, which
happens when execution hits a configured stop filter.
Tested that hitting a stop filter while PT recording successfully
records a trace with this patch but crashes without this patch.
Fixes: 670638477aed ("perf/x86/intel/pt: Opportunistically use single range output mode") Signed-off-by: Tristan Hume <tristan@thume.ca> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@kernel.org Link: https://lkml.kernel.org/r/20220127220806.73664-1-tristan@thume.ca Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An event may have a number of uncore aliases that when added to the
evlist are consecutive.
If there are multiple uncore events in a group then
parse_events__set_leader_for_uncore_aliase will reorder the evlist so
that events on the same PMU are adjacent.
The collect_all_aliases function assumes that aliases are in blocks so
that only the first counter is printed and all others are marked merged.
The reordering for groups breaks the assumption and so all counts are
printed.
This change removes the assumption from collect_all_aliases
that the events are in blocks and instead processes the entire evlist.
Before:
```
$ perf stat -e '{UNC_CHA_TOR_OCCUPANCY.IA_MISS_DRD_REMOTE,UNC_CHA_TOR_INSERTS.IA_MISS_DRD_REMOTE},duration_time' -a -A -- sleep 1
Add a config option CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION to
enable bitblt and fillrect hardware acceleration in the framebuffer
console. If disabled, such acceleration will not be used, even if it is
supported by the graphics hardware driver.
If you plan to use DRM as your main graphics output system, you should
disable this option since it will prevent compiling in code which isn't
used later on when DRM takes over.
For all other configurations, e.g. if none of your graphic cards support
DRM (yet), DRM isn't available for your architecture, or you can't be
sure that the graphic card in the target system will support DRM, you
most likely want to enable this option.
In the non-accelerated case (e.g. when DRM is used), the inlined
fb_scrollmode() function is hardcoded to return SCROLL_REDRAW and as such the
compiler is able to optimize much unneccesary code away.
In this v3 patch version I additionally changed the GETVYRES() and GETVXRES()
macros to take a pointer to the fbcon_display struct. This fixes the build when
console rotation is enabled and helps the compiler again to optimize out code.
Revert the first (of 2) commits which disabled scrolling acceleration in
fbcon/fbdev. It introduced a regression for fbdev-supported graphic cards
because of the performance penalty by doing screen scrolling by software
instead of using the existing graphic card 2D hardware acceleration.
Console scrolling acceleration was disabled by dropping code which
checked at runtime the driver hardware capabilities for the
BINFO_HWACCEL_COPYAREA or FBINFO_HWACCEL_FILLRECT flags and if set, it
enabled scrollmode SCROLL_MOVE which uses hardware acceleration to move
screen contents. After dropping those checks scrollmode was hard-wired
to SCROLL_REDRAW instead, which forces all graphic cards to redraw every
character at the new screen position when scrolling.
This change effectively disabled all hardware-based scrolling acceleration for
ALL drivers, because now all kind of 2D hardware acceleration (bitblt,
fillrect) in the drivers isn't used any longer.
The original commit message mentions that only 3 DRM drivers (nouveau, omapdrm
and gma500) used hardware acceleration in the past and thus code for checking
and using scrolling acceleration is obsolete.
This statement is NOT TRUE, because beside the DRM drivers there are around 35
other fbdev drivers which depend on fbdev/fbcon and still provide hardware
acceleration for fbdev/fbcon.
The original commit message also states that syzbot found lots of bugs in fbcon
and thus it's "often the solution to just delete code and remove features".
This is true, and the bugs - which actually affected all users of fbcon,
including DRM - were fixed, or code was dropped like e.g. the support for
software scrollback in vgacon (commit 973c096f6a85).
So to further analyze which bugs were found by syzbot, I've looked through all
patches in drivers/video which were tagged with syzbot or syzkaller back to
year 2005. The vast majority fixed the reported issues on a higher level, e.g.
when screen is to be resized, or when font size is to be changed. The few ones
which touched driver code fixed a real driver bug, e.g. by adding a check.
But NONE of those patches touched code of either the SCROLL_MOVE or the
SCROLL_REDRAW case.
That means, there was no real reason why SCROLL_MOVE had to be ripped-out and
just SCROLL_REDRAW had to be used instead. The only reason I can imagine so far
was that SCROLL_MOVE wasn't used by DRM and as such it was assumed that it
could go away. That argument completely missed the fact that SCROLL_MOVE is
still heavily used by fbdev (non-DRM) drivers.
Some people mention that using memcpy() instead of the hardware acceleration is
pretty much the same speed. But that's not true, at least not for older graphic
cards and machines where we see speed decreases by factor 10 and more and thus
this change leads to console responsiveness way worse than before.
That's why the original commit is to be reverted. By reverting we
reintroduce hardware-based scrolling acceleration and fix the
performance regression for fbdev drivers.
There isn't any impact on DRM when reverting those patches.
There's limiting the year to 2069. When setting the rtc year to 2070,
reading it returns 1970. Evaluate century starting from 19 to count the
correct year.
$ sudo date -s 20700106
Mon 06 Jan 2070 12:00:00 AM CST
$ sudo hwclock -w
$ sudo hwclock -r
1970-01-06 12:00:49.604968+08:00
Fixes: 2a4daadd4d3e5071 ("rtc: cmos: ignore bogus century byte") Signed-off-by: Riwen Lu <luriwen@kylinos.cn> Acked-by: Eric Wong <e@80x24.org> Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20220106084609.1223688-1-luriwen@kylinos.cn Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl> # preparation for stable Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with 'make -s', there is some output from resolve_btfids:
$ make -sj"$(nproc)" oldconfig prepare
MKDIR .../tools/bpf/resolve_btfids/libbpf/
MKDIR .../tools/bpf/resolve_btfids//libsubcmd
LINK resolve_btfids
Silent mode means that no information should be emitted about what is
currently being done. Use the $(silent) variable from Makefile.include
to avoid defining the msg macro so that there is no information printed.
Fixes: fbbb68de80a4 ("bpf: Add resolve_btfids tool to resolve BTF IDs in ELF object") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220201212503.731732-1-nathan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recursive make commands should always use the variable MAKE, not the
explicit command name ‘make’. This has benefits and removes the
following warning when multiple jobs are used for the build:
make[2]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule.
Fixes: a8ba798bc8ec ("selftests: enable O and KBUILD_OUTPUT") Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Reviewed-by: André Almeida <andrealmeid@collabora.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pipe named FIFO special file is being created in execveat.c to perform
some tests. Makefile doesn't need to do anything with the pipe. When it
isn't found, Makefile generates the following build error:
make: *** No rule to make target
'../tools/testing/selftests/exec/pipe', needed by 'all'. Stop.
After commit 2fd3fb0be1d1 ("kasan, vmalloc: unpoison VM_ALLOC pages
after mapping"), non-VM_ALLOC mappings will be marked as accessible
in __get_vm_area_node() when KASAN is enabled. But now the flag for
ringbuf area is VM_ALLOC, so KASAN will complain out-of-bound access
after vmap() returns. Because the ringbuf area is created by mapping
allocated pages, so use VM_MAP instead.
After the change, info in /proc/vmallocinfo also changes from
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmalloc user
to
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmap user
Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it") Reported-by: syzbot+5ad567a418794b9b5983@syzkaller.appspotmail.com Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20220202060158.6260-1-houtao1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'tail' and 'head' are 'unsigned int' type free-running count, when
'head' is overflow, the 'int i (= tail) < u32 head' will be false:
Only '- loop 0: idx = 63' result is shown, so it needs to use 'int' type
to compare, it can handle the overflow correctly.
typedef uint32_t u32;
int main()
{
u32 tail, head;
int stail, shead;
int i, loop;
tail = 0xffffffff;
head = 0x00000000;
for (i = tail, loop = 0; i < head; i++) {
unsigned int idx = i & 63;
printf("+ loop %d: idx = %u\n", loop++, idx);
}
stail = tail;
shead = head;
for (i = stail, loop = 0; i < shead; i++) {
unsigned int idx = i & 63;
printf("- loop %d: idx = %u\n", loop++, idx);
}
return 0;
}
Fixes: 5cdad90de62c ("gve: Batch AQ commands for creating and destroying queues.") Signed-off-by: Haiyue Wang <haiyue.wang@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
o The server has not recorded an unconfirmed { v, x, c, *, * } and
has recorded a confirmed { v, x, c, *, s }. If the principals of
the record and of SETCLIENTID_CONFIRM do not match, the server
returns NFS4ERR_CLID_INUSE without removing any relevant leased
client state, and without changing recorded callback and
callback_ident values for client { x }.
The current code intends to do what the spec describes above but
it forgot to set 'old' to NULL resulting to the confirmed client
to be expired.
Fixes: 2b63482185e6 ("nfsd: fix clid_inuse on mount with security change") Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: Bruce Fields <bfields@fieldses.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running tests with a debug kernel shows that bnx2fc_recv_frame() is
modifying the per_cpu lport stats counters in a non-mpsafe way. Just boot
a debug kernel and run the bnx2fc driver with the hardware enabled.
After commit 266423e60ea1 ("pinctrl: bcm2835: Change init order for gpio
hogs") a few error paths would not unwind properly the registration of
gpio ranges. Correct that by assigning a single error label and goto it
whenever we encounter a fatal error.
ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:
->handle_irq(): 000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
IRQ_NOPROBE set
unexpected IRQ trap at vector 7c
The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.
projects / users / dwmw2 / linux.git / log