Beacon elements might be changed by hostapd configuraion, so driver
should compare both IEs and PHY capabilities to get the least common
denominator before association.
Co-developed-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes: 67aa27431c7f8 ("mt76: mt7921: rely on mt76_connac_mcu common library") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Xing Song [Thu, 30 Sep 2021 07:37:37 +0000 (15:37 +0800)]
mt76: use a separate CCMP PN receive counter for management frames
When received frame is decryped by hardware, CCMP PN is checked by
mt76.
When management frame protection (IEEE 802.11w) is used, we must use
a separate counter for tracking received CCMP packet number for the
management frames. The previously used counter was shared with data
frames and that can cause problems in detecting replays incorrectly
for robust management frames.
Add a new counter just for robust management frames to avoid this
issue.
Signed-off-by: Xing Song <xing.song@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Fri, 17 Sep 2021 23:54:21 +0000 (07:54 +0800)]
mt76: drop MCU header size from buffer size in __mt76_mcu_send_firmware
Each firmware piece with mt7915 and mt7921 do not have the MCU header to
reroute the packet to the internal RAM. So we do not need to consider the
MCU header size in __mt76_mcu_send_firmware.
Move the MCU header overhead calculation to mt76_mcu_send_firmware (for
older chipsets)
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Wed, 15 Sep 2021 15:07:45 +0000 (17:07 +0200)]
mt76: introduce __mt76_mcu_send_firmware routine
Introduce __mt76_mcu_send_firmware routine to specify mcu message max
length. This is a preliminary patch to support mt7921s driver.
Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Wed, 25 Aug 2021 01:32:16 +0000 (02:32 +0100)]
mt76: support reading EEPROM data embedded in fdt
Some platforms boot from SD card and don't come with calibration data
stored anywhere on the board.
As EEPROM data is rather small it can be embedded into the device tree
to be loaded from there by the mt76.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Mon, 13 Sep 2021 09:25:05 +0000 (11:25 +0200)]
mt76: schedule status timeout at dma completion
Reduce MT_TX_STATUS_SKB_TIMEOUT to 250ms
Tested-by: mrkiko.rs@gmail.com Co-developed-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Tue, 24 Aug 2021 10:22:23 +0000 (12:22 +0200)]
mt76: connac: add 6GHz support to mt76_connac_mcu_sta_tlv
Introduce sta_rec_he_6g_capa tlv in order configure the mcu with 6GHz
capabilities. This is a preliminary patch to enable 6GHz band for
mt7921 devices.
Tested-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ben Greear [Wed, 4 Aug 2021 13:43:34 +0000 (06:43 -0700)]
mt76: mt7915: add more MIB registers
Add register definitions and read & accumulate them in
the mib polling logic. Note that some registers should not
be read since firmware is already reading them. If driver
reads those, they will be cleared-on-read, and so the firmware
stats will be incorrect.
For these 'do-not-read' stats, add them to the registers definition
so that other developers can be aware of these constraints, but do
not actually read them in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ben Greear [Wed, 4 Aug 2021 13:43:32 +0000 (06:43 -0700)]
mt76: mt7915: add tx mu/su counters to mib
These counters are clear-on-read, so we need to accumulate
them in the update_stats poll logic, and read the accumulated
values instead of directly doing register reads when reporting
to debugfs and ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Tue, 14 Sep 2021 15:50:22 +0000 (23:50 +0800)]
mt76: mt7921: fix retrying release semaphore without end
We should pass the error code to the caller immediately
to avoid the possible infinite retry to release the semaphore.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support") Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Robustify hardware initialization in the current driver probing flow
to get rid of the device is possibly lost after the machine boot due
to possible firmware abnormal state by trying to recover the failure
with more chances.
Tested-by: Leon Yen <Leon.Yen@mediatek.com> Tested-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Sat, 4 Sep 2021 10:16:45 +0000 (12:16 +0200)]
mt76: mt7921: report tx rate directly from tx status
Report tx rate from tx status packets instead of receiving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ben Greear [Thu, 2 Sep 2021 05:52:03 +0000 (13:52 +0800)]
mt76: mt7915: fix hwmon temp sensor mem use-after-free
Without this change, garbage is seen in the hwmon name and sensors output
for mt7915 is garbled. It appears that the hwmon logic does not make a
copy of the incoming string, but instead just copies a char* and expects
it to never go away.
Fixes: 33fe9c639c13 ("mt76: mt7915: add thermal sensor device support") Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 24 Sep 2021 15:54:40 +0000 (17:54 +0200)]
mt76: disable BH around napi_schedule() calls
napi_schedule() can call __raise_softirq_irqoff(), which can perform softirq
handling, so it must not be called in a pure process context with BH enabled.
jing yangyang [Fri, 20 Aug 2021 02:41:17 +0000 (19:41 -0700)]
mt76: fix boolreturn.cocci warnings
./drivers/net/wireless/mediatek/mt76/mt7615/usb_sdio.c:172:8-9:WARNING:
return of 0/1 in function 'mt7663_usb_sdio_tx_status_data' with return
type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Felix Fietkau [Wed, 8 Sep 2021 15:46:44 +0000 (17:46 +0200)]
mt76: mt7915: fix WMM index on DBDC cards
WMM index range needs to be split between both PHYs if a second PHY exists.
The condition for that was accidentally written as checking if the vif PHY
is the secondary one
Lorenzo Bianconi [Fri, 2 Jul 2021 17:44:09 +0000 (19:44 +0200)]
mt76: mt7915: introduce bss coloring support
Introduce mcu APIs to configure bss coloring and to report bss coloring
collisions. Add support to report coloring countdown in beacon sent by
the device.
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
MeiChia Chiu [Sat, 28 Aug 2021 17:02:38 +0000 (01:02 +0800)]
mt76: mt7915: add LED support
Initialize brightness_set and blink_set callbacks to enable LED support.
The base 0x7c000000 is MCU space so driver can't touch it, and should
map the LED base to 0x18000000 host's view.
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Money Wang <money.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ryder Lee [Thu, 17 Jun 2021 20:39:00 +0000 (04:39 +0800)]
mt76: use IEEE80211_OFFLOAD_ENCAP_ENABLED instead of MT_DRV_AMSDU_OFFLOAD
Drop MT_DRV_AMSDU_OFFLOAD after introducing IEEE80211_OFFLOAD_ENCAP_ENABLED
flag in mac80211. Driver now checks vif->offload_flags to know encap offload
status of each interface.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Wed, 11 Aug 2021 05:58:24 +0000 (13:58 +0800)]
mt76: mt7921: fix firmware usage of RA info using legacy rates
According to the firmware usage, OFDM rates should fill out bit 6 - 13
while CCK rates should fill out bit 0 - 3 in legacy field of RA info to
make the rate adaption runs propertly. Otherwise, a unicast frame might be
picking up the unsupported rate to send out.
Fixes: 1c099ab44727 ("mt76: mt7921: add MCU support") Reported-by: Joshua Emele <jemele@chromium.org> Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Sun, 8 Aug 2021 19:11:49 +0000 (21:11 +0200)]
mt76: overwrite default reg_ops if necessary
Introduce mt76_register_debugfs_fops routine in order to
define per-driver regs file operations and make sure the
device is up before reading or writing its registers
Introduce mt7921_mcu_set_beacon_filter utility routine in order to
remove duplicated code for hw beacon filtering.
Move mt7921_pm_interface_iter in debugfs since it is just used there.
Make the following routine static:
- mt7921_pm_interface_iter
- mt7921_mcu_uni_bss_bcnft
- mt7921_mcu_set_bss_pm
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
YN Chen [Wed, 4 Aug 2021 22:23:00 +0000 (06:23 +0800)]
mt76: connac: add support for limiting to maximum regulatory Tx power
Consider .max_reg_power in struct ieee80211_channel to limit the
maximum power the wireless device allowed to transmit on the
corresponding channel according to the regulatory domain.
Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update the proper firmware programming sequence to fix GTK rekey
offload failure on WPA mixed mode.
In the mt76_connac_mcu_key_iter,
gtk_tlv->proto should be only set up on pairwise key
and gtk_tlk->group_cipher should be only set up on the group key.
Otherwise, those parameters required by firmware would be set
incorrectly to cause GTK rekey offload failure on WPA mixed mode
and then disconnection follows.
Fixes: b47e21e75c80 ("mt76: mt7615: add gtk rekey offload support") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Leon Yen <Leon.Yen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Deren Wu [Tue, 27 Jul 2021 09:47:09 +0000 (17:47 +0800)]
mt76: mt7921: fix dma hang in rmmod
The dma would be broken after rmmod flow. There are two different
cases causing this issue.
1. dma access without privilege.
2. hw access sequence borken by another context.
This patch handle both cases to avoid hw crash.
Fixes: 2b9ea5a8cf1bd ("mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device") Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
The bit fields of tx rate idx should be 6 bits, otherwise it might be
incorrect in HT mode.
For VHT/HE rates, only 4 bits are actually used by rate idx, the other
2 bits are used for other functions.
Fixes: c31d94af1843 ("mt76: mt7915: fix tx rate related fields in tx descriptor") Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76: mt7915: switch proper tx arbiter mode in testmode
Switch proper tx arbiter mode during testmode tx to prevent from
entering the flow of normal tx in FW.
Also, testmode SU and MU tx need to use different arbiter mode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Deren Wu [Thu, 15 Jul 2021 17:34:19 +0000 (01:34 +0800)]
mt76: mt7921: Add mt7922 support
Add new chip mt7922 in mt7921 module with following items
1. new chip ID / fw bin name
2. is_mt7922()
check chip type for different fw files
3. mt7921_get_data_mode()
check security type of fw (backward compatible)
Co-developed-by: Jimmy Hu <Jimmy.Hu@mediatek.com> Signed-off-by: Jimmy Hu <Jimmy.Hu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 21 Jul 2021 05:23:46 +0000 (07:23 +0200)]
mt76: mt7615: fix skb use-after-free on mac reset
When clearing all existing pending tx slots, mt76_tx_complete_skb needs to
be used to free the skbs, to ensure that they are cleared from the status
list as well.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name>
Deren Wu [Wed, 14 Jul 2021 15:50:52 +0000 (23:50 +0800)]
mt76: mt7921: Fix out of order process by invalid event pkt
The acceptable event report should inlcude original CMD-ID. Otherwise,
drop unexpected result from fw.
Fixes: 1c099ab44727c ("mt76: mt7921: add MCU support") Signed-off-by: Jimmy Hu <Jimmy.Hu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Tue, 13 Jul 2021 20:16:01 +0000 (04:16 +0800)]
mt76: mt7915: fix mgmt frame using unexpected bitrate
Fix the current driver mgmt frame is not respecting the basic rates field
provided by the AP and then unconditionally is using the lowest (1 or 6
Mbps) rate.
For example, if the AP only supported basic rate {24, 36, 48, 54} Mbps,
mt7921 cannot send mgmt frame with the rate not in the group. So,
instead, we pick up the lowest basic rate the AP can support to send.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Suggested-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Tue, 13 Jul 2021 20:16:00 +0000 (04:16 +0800)]
mt76: mt7921: fix mgmt frame using unexpected bitrate
Fix the current driver mgmt frame is not respecting the basic rates field
provided by the AP and then unconditionally is using the lowest (1 or 6
Mbps) rate.
For example, if the AP only supported basic rate {24, 36, 48, 54} Mbps,
mt7921 cannot send mgmt frame with the rate not in the group. So,
instead, we pick up the lowest basic rate the AP can support to send.
Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Mon, 21 Jun 2021 09:23:26 +0000 (11:23 +0200)]
mt76: mt7921: introduce testmode support
We add the testmode support to access the testmode feature provided
by the MT7921 firmware.
Tested-by: Sean Wang <sean.wang@mediatek.com> Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ryder Lee [Wed, 14 Jul 2021 09:18:50 +0000 (17:18 +0800)]
mt76: mt7915: report tx rate directly from tx status
Report tx rate from tx status packets instead of receving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ryder Lee [Wed, 14 Jul 2021 09:18:48 +0000 (17:18 +0800)]
mt76: mt7915: take RCU read lock when calling ieee80211_bss_get_elem()
As ieee80211_bss_get_elem() derefences an RCU to return ie, both
the call to this function and any operation on this variable need
protection by the RCU read lock.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
projects / users / jedix / linux-maple.git / log