recalculate_apic_map does not santize ldr and it's possible that
multiple bits are set. In that case, a previous valid entry
can potentially be overwritten by an invalid one.
This condition is hit when booting a 32 bit, >8 CPU, RHEL6 guest and then
triggering a crash to boot a kdump kernel. This is the sequence of
events:
1. Linux boots in bigsmp mode and enables PhysFlat, however, it still
writes to the LDR which probably will never be used.
2. However, when booting into kdump, the stale LDR values remain as
they are not cleared by the guest and there isn't a apic reset.
3. kdump boots with 1 cpu, and uses Logical Destination Mode but the
logical map has been overwritten and points to an inactive vcpu.
Signed-off-by: Radim Krcmar <rkrcmar@redhat.com> Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The input pool of a client might be deleted via the resize ioctl, the
the access to it should be covered by the proper locks. Currently the
only missing place is the call in snd_seq_ioctl_get_client_pool(), and
this patch papers over it.
I forgot to release the allocated object at the early error path in
line6_init_pcm(). For addressing it, slightly shuffle the code so
that the PCM destructor (pcm->private_free) is assigned properly
before all error paths.
As Jason Baron explained in commit 790ba4566c1a ("tcp: set SOCK_NOSPACE
under memory pressure"), it is crucial we properly set SOCK_NOSPACE
when needed.
However, Jason patch had a bug, because the 'nonblocking' status
as far as sk_stream_wait_memory() is concerned is governed
by MSG_DONTWAIT flag passed at sendmsg() time :
long timeo = sock_sndtimeo(sk, flags & MSG_DONTWAIT);
So it is very possible that tcp sendmsg() calls sk_stream_wait_memory(),
and that sk_stream_wait_memory() returns -EAGAIN with SOCK_NOSPACE
cleared, if sk->sk_sndtimeo has been set to a small (but not zero)
value.
This patch removes the 'noblock' variable since we must always
set SOCK_NOSPACE if -EAGAIN is returned.
It also renames the do_nonblock label since we might reach this
code path even if we were in blocking mode.
Fixes: 790ba4566c1a ("tcp: set SOCK_NOSPACE under memory pressure") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason Baron <jbaron@akamai.com> Reported-by: Vladimir Rutsky <rutsky@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we are only explicitly setting SOCK_NOSPACE on a write timeout
for non-blocking sockets. Epoll() edge-trigger mode relies on SOCK_NOSPACE
being set when -EAGAIN is returned to ensure that EPOLLOUT is raised.
Expand the setting of SOCK_NOSPACE to non-blocking sockets as well that can
use SO_SNDTIMEO to adjust their write timeout. This mirrors the behavior
that Eric Dumazet introduced for tcp sockets.
Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Ursula Braun <ubraun@linux.ibm.com> Cc: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `uac_mixer_unit_descriptor` shown as below is read from the
device side. In `parse_audio_mixer_unit`, `baSourceID` field is
accessed from index 0 to `bNrInPins` - 1, the current implementation
assumes that descriptor is always valid (the length of descriptor
is no shorter than 5 + `bNrInPins`). If a descriptor read from
the device side is invalid, it may trigger out-of-bound memory
access.
`check_input_term` recursively calls itself with input from
device side (e.g., uac_input_terminal_descriptor.bCSourceID)
as argument (id). In `check_input_term`, if `check_input_term`
is called with the same `id` argument as the caller, it triggers
endless recursive call, resulting kernel space stack overflow.
This patch fixes the bug by adding a bitmap to `struct mixer_build`
to keep track of the checked ids and stop the execution if some id
has been checked (similar to how parse_audio_unit handles unitid
argument).
tcp_rtx_queue_tail() (called by tcp_fragment()) can call
tcp_write_queue_prev() on the first packet in the queue, which will trigger
the BUG in tcp_write_queue_prev(), because there is no previous packet.
This happens when the retransmit queue is empty, for example in case of a
zero window.
Commit 8c3088f895a0 ("tcp: be more careful in tcp_fragment()") was not a
simple cherry-pick of the original one from master (b617158dc096)
because there is a specific TCP rtx queue only since v4.15. For more
details, please see the commit message of b617158dc096 ("tcp: be more
careful in tcp_fragment()").
The BUG() is hit due to the specific code added to versions older than
v4.15. The comment in skb_queue_prev() (include/linux/skbuff.h:1406),
just before the BUG_ON() somehow suggests to add a check before using
it, what Tim did.
In master, this code path causing the issue will not be taken because
the implementation of tcp_rtx_queue_tail() is different:
Fixes: 8c3088f895a0 ("tcp: be more careful in tcp_fragment()") Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Reviewed-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Register cpufreq notifier after we have initialized the crtc and
unregister it before we remove the ctrc. Receiving a cpufreq notify
without crtc causes a crash.
Fix RX_TERMINATION_FORCE_ENABLE define value from 0x0089 to 0x00A9
according to MIPI Alliance MPHY specification.
Fixes: e785060ea3a1 ("ufs: definitions for phy interface") Signed-off-by: Pedro Sousa <sousa@synopsys.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 5e6acc3e678e ("bcm2835-pm: Move bcm2835-watchdog's DT probe
to an MFD.") broke module autoloading on Raspberry Pi. So add a
module alias this fix this.
In read_per_ring_refs(), after 'req' and related memory regions are
allocated, xen_blkif_map() is invoked to map the shared frame, irq, and
etc. However, if this mapping process fails, no cleanup is performed,
leading to memory leaks. To fix this issue, invoke the cleanup before
returning the error.
Acked-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If fsg_disable() and fsg_set_alt() are called too closely to each
other (for example due to a quick reset/reconnect), what can happen
is that fsg_set_alt sets common->new_fsg from an interrupt while
handle_exception is trying to process the config change caused by
fsg_disable():
fsg_disable()
...
handle_exception()
sets state back to FSG_STATE_NORMAL
hasn't yet called do_set_interface()
or is inside it.
---> interrupt
fsg_set_alt
sets common->new_fsg
queues a new FSG_STATE_CONFIG_CHANGE
<---
Now, the first handle_exception can "see" the updated
new_fsg, treats it as if it was a fsg_set_alt() response,
call usb_composite_setup_continue() etc...
But then, the thread sees the second FSG_STATE_CONFIG_CHANGE,
and goes back down the same path, wipes and reattaches a now
active fsg, and .. calls usb_composite_setup_continue() which
at this point is wrong.
Not only we get a backtrace, but I suspect the second set_interface
wrecks some state causing the host to get upset in my case.
This fixes it by replacing "new_fsg" by a "state argument" (same
principle) which is set in the same lock section as the state
update, and retrieved similarly.
That way, there is never any discrepancy between the dequeued
state and the observed value of it. We keep the ability to have
the latest reconfig operation take precedence, but we guarantee
that once "dequeued" the argument (new_fsg) will not be clobbered
by any new event.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since scatterlist dimensions are all unsigned ints, in the relatively
rare cases where a device's max_segment_size is set to UINT_MAX, then
the "cur_len + s_length <= max_len" check in __finalise_sg() will always
return true. As a result, the corner case of such a device mapping an
excessively large scatterlist which is mergeable to or beyond a total
length of 4GB can lead to overflow and a bogus truncated dma_length in
the resulting segment.
As we already assume that any single segment must be no longer than
max_len to begin with, this can easily be addressed by reshuffling the
comparison.
clang-9 points out that there are two variables that depending on the
configuration may only be used in an ARRAY_SIZE() expression but not
referenced:
drivers/dma/ste_dma40.c:145:12: error: variable 'd40_backup_regs' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs[] = {
^
drivers/dma/ste_dma40.c:214:12: error: variable 'd40_backup_regs_chan' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs_chan[] = {
Alastair D'Silva [Wed, 21 Aug 2019 00:19:27 +0000 (10:19 +1000)]
powerpc: Allow flush_(inval_)dcache_range to work across ranges >4GB
The upstream commit: 22e9c88d486a ("powerpc/64: reuse PPC32 static inline flush_dcache_range()")
has a similar effect, but since it is a rewrite of the assembler to C, is
too invasive for stable. This patch is a minimal fix to address the issue in
assembler.
This patch applies cleanly to v5.2, v4.19 & v4.14.
When calling flush_(inval_)dcache_range with a size >4GB, we were masking
off the upper 32 bits, so we would incorrectly flush a range smaller
than intended.
This patch replaces the 32 bit shifts with 64 bit ones, so that
the full size is accounted for.
This function is supposed to return error pointers so it matches the
dmz_get_rnd_zone_for_reclaim() function. The current code could lead to
a NULL dereference in dmz_do_reclaim()
Fixes: b234c6d7a703 ("dm zoned: improve error handling in reclaim") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
================================================
WARNING: lock held when returning to user space!
5.3.0-rc5 #rc5 Tainted: G W
------------------------------------------------
chgrp/47006 is leaving the kernel with locks still held!
1 lock held by chgrp/47006:
#0: 000000006664ea2d (&xfs_nondir_ilock_class){++++}, at: xfs_ilock+0xd2/0x290 [xfs]
...which is clearly caused by xfs_setattr_nonsize failing to unlock the
ILOCK after the xfs_qm_vop_chown_reserve call fails. Add the missing
unlock.
Reported-by: benjamin.moody@gmail.com Fixes: 253f4911f297 ("xfs: better xfs_trans_alloc interface") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In zs_destroy_pool() we call flush_work(&pool->free_work). However, we
have no guarantee that migration isn't happening in the background at
that time.
Since migration can't directly free pages, it relies on free_work being
scheduled to free the pages. But there's nothing preventing an
in-progress migrate from queuing the work *after*
zs_unregister_migration() has called flush_work(). Which would mean
pages still pointing at the inode when we free it.
Since we know at destroy time all objects should be free, no new
migrations can come in (since zs_page_isolate() fails for fully-free
zspages). This means it is sufficient to track a "# isolated zspages"
count by class, and have the destroy logic ensure all such pages have
drained before proceeding. Keeping that state under the class spinlock
keeps the logic straightforward.
In this case a memory leak could lead to an eventual crash if compaction
hits the leaked page. This crash would only occur if people are
changing their zswap backend at runtime (which eventually starts
destruction).
Link: http://lkml.kernel.org/r/20190809181751.219326-2-henryburns@google.com Fixes: 48b4800a1c6a ("zsmalloc: page migration support") Signed-off-by: Henry Burns <henryburns@google.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Henry Burns <henrywolfeburns@gmail.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Jonathan Adams <jwadams@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In zs_page_migrate() we call putback_zspage() after we have finished
migrating all pages in this zspage. However, the return value is
ignored. If a zs_free() races in between zs_page_isolate() and
zs_page_migrate(), freeing the last object in the zspage,
putback_zspage() will leave the page in ZS_EMPTY for potentially an
unbounded amount of time.
To fix this, we need to do the same thing as zs_page_putback() does:
schedule free_work to occur.
To avoid duplicated code, move the sequence to a new
putback_zspage_deferred() function which both zs_page_migrate() and
zs_page_putback() call.
Link: http://lkml.kernel.org/r/20190809181751.219326-1-henryburns@google.com Fixes: 48b4800a1c6a ("zsmalloc: page migration support") Signed-off-by: Henry Burns <henryburns@google.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Henry Burns <henrywolfeburns@gmail.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Jonathan Adams <jwadams@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
THP splitting path is missing the split_page_owner() call that
split_page() has.
As a result, split THP pages are wrongly reported in the page_owner file
as order-9 pages. Furthermore when the former head page is freed, the
remaining former tail pages are not listed in the page_owner file at
all. This patch fixes that by adding the split_page_owner() call into
__split_huge_page().
Link: http://lkml.kernel.org/r/20190820131828.22684-2-vbabka@suse.cz Fixes: a9627bc5e34e ("mm/page_owner: introduce split_page_owner and replace manual handling") Reported-by: Kirill A. Shutemov <kirill@shutemov.name> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If alloc_descs() fails before irq_sysfs_init() has run, free_desc() in the
cleanup path will call kobject_del() even though the kobject has not been
added with kobject_add().
Fix this by making the call to kobject_del() conditional on whether
irq_sysfs_init() has run.
This problem surfaced because commit aa30f47cf666 ("kobject: Add support
for default attribute groups to kobj_type") makes kobject_del() stricter
about pairing with kobject_add(). If the pairing is incorrrect, a WARNING
and backtrace occur in sysfs_remove_group() because there is no parent.
[ tglx: Add a comment to the code and make it work with CONFIG_SYSFS=n ]
Fixes: ecb3f394c5db ("genirq: Expose interrupt information through sysfs") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1564703564-4116-1-git-send-email-mikelley@microsoft.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm-zoned is observed to lock up or livelock in case of hardware
failure or some misconfiguration of the backing zoned device.
This patch adds a new dm-zoned target function that checks the status of
the backing device. If the request queue of the backing device is found
to be in dying state or the SCSI backing device enters offline state,
the health check code sets a dm-zoned target flag prompting all further
incoming I/O to be rejected. In order to detect backing device failures
timely, this new function is called in the request mapping path, at the
beginning of every reclaim run and before performing any metadata I/O.
The proper way out of this situation is to do
dmsetup remove <dm-zoned target>
and recreate the target when the problem with the backing device
is resolved.
Fixes: 3b1a94c88b79 ("dm zoned: drive-managed zoned block device target") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some errors are ignored in the I/O path during queueing chunks
for processing by chunk works. Since at least these errors are
transient in nature, it should be possible to retry the failed
incoming commands.
The fix -
Errors that can happen while queueing chunks are carried upwards
to the main mapping function and it now returns DM_MAPIO_REQUEUE
for any incoming requests that can not be properly queued.
Error logging/debug messages are added where needed.
Fixes: 3b1a94c88b79 ("dm zoned: drive-managed zoned block device target") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several places in reclaim code where errors are not
propagated to the main function, dmz_reclaim(). This function
is responsible for unlocking zones that might be still locked
at the end of any failed reclaim iterations. As the result,
some device zones may be left permanently locked for reclaim,
degrading target's capability to reclaim zones.
This patch fixes these issues as follows -
Make sure that dmz_reclaim_buf(), dmz_reclaim_seq_data() and
dmz_reclaim_rnd_data() return error codes to the caller.
dmz_reclaim() function is renamed to dmz_do_reclaim() to avoid
clashing with "struct dmz_reclaim" and is modified to return the
error to the caller.
dmz_get_zone_for_reclaim() now returns an error instead of NULL
pointer and reclaim code checks for that error.
Error logging/debug messages are added where necessary.
Fixes: 3b1a94c88b79 ("dm zoned: drive-managed zoned block device target") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the sector number is too high, dm_table_find_target() should return a
pointer to a zeroed dm_target structure (the caller should test it with
dm_target_is_valid).
However, for some table sizes, the code in dm_table_find_target() that
performs btree lookup will access out of bound memory structures.
Fix this bug by testing the sector number at the beginning of
dm_table_find_target(). Also, add an "inline" keyword to the function
dm_table_get_size() because this is a hot path.
In commit 6096d91af0b6 ("dm space map metadata: fix occasional leak
of a metadata block on resize"), we refactor the commit logic to a new
function 'apply_bops'. But when that logic was replaced in out() the
return value was not stored. This may lead out() returning a wrong
value to the caller.
Fixes: 6096d91af0b6 ("dm space map metadata: fix occasional leak of a metadata block on resize") Cc: stable@vger.kernel.org Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When btree_split_beneath() splits a node to two new children, it will
allocate two blocks: left and right. If right block's allocation
failed, the left block will be unlocked and marked dirty. If this
happened, the left block'ss content is zero, because it wasn't
initialized with the btree struct before the attempot to allocate the
right block. Upon return, when flushing the left block to disk, the
validator will fail when check this block. Then a BUG_ON is raised.
Fix this by completely initializing the left block before allocating and
initializing the right block.
Fixes: 4dcb8b57df359 ("dm btree: fix leak of bufio-backed block in btree_split_beneath error path") Cc: stable@vger.kernel.org Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a problem in dm-kcopyd that may leave jobs in
complete queue indefinitely in the event of backing storage failure.
This behavior has been observed while running 100% write file fio
workload against an XFS volume created on top of a dm-zoned target
device. If the underlying storage of dm-zoned goes to offline state
under I/O, kcopyd sometimes never issues the end copy callback and
dm-zoned reclaim work hangs indefinitely waiting for that completion.
This behavior was traced down to the error handling code in
process_jobs() function that places the failed job to complete_jobs
queue, but doesn't wake up the job handler. In case of backing device
failure, all outstanding jobs may end up going to complete_jobs queue
via this code path and then stay there forever because there are no
more successful I/O jobs to wake up the job handler.
This patch adds a wake() call to always wake up kcopyd job wait queue
for all I/O jobs that fail before dm_io() gets called for that job.
The patch also sets the write error status in all sub jobs that are
failed because their master job has failed.
Fixes: b73c67c2cbb00 ("dm kcopyd: add sequential write feature") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90118c445cc ("x86/boot: Save fields explicitly, zero out everything
else") had two errors:
* It preserved boot_params.acpi_rsdp_addr, and
* It failed to preserve boot_params.hdr
Therefore, zero out acpi_rsdp_addr, and preserve hdr.
Fixes: a90118c445cc ("x86/boot: Save fields explicitly, zero out everything else") Reported-by: Neil MacLeod <neil@nmacleod.com> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Neil MacLeod <neil@nmacleod.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190821192513.20126-1-jhubbard@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent gcc compilers (gcc 9.1) generate warnings about an out of bounds
memset, if the memset goes accross several fields of a struct. This
generated a couple of warnings on x86_64 builds in sanitize_boot_params().
Fix this by explicitly saving the fields in struct boot_params
that are intended to be preserved, and zeroing all the rest.
[ tglx: Tagged for stable as it breaks the warning free build there as well ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Suggested-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190731054627.5627-2-jhubbard@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been reports of RDRAND issues after resuming from suspend on
some AMD family 15h and family 16h systems. This issue stems from a BIOS
not performing the proper steps during resume to ensure RDRAND continues
to function properly.
RDRAND support is indicated by CPUID Fn00000001_ECX[30]. This bit can be
reset by clearing MSR C001_1004[62]. Any software that checks for RDRAND
support using CPUID, including the kernel, will believe that RDRAND is
not supported.
Update the CPU initialization to clear the RDRAND CPUID bit for any family
15h and 16h processor that supports RDRAND. If it is known that the family
15h or family 16h system does not have an RDRAND resume issue or that the
system will not be placed in suspend, the "rdrand=force" kernel parameter
can be used to stop the clearing of the RDRAND CPUID bit.
Additionally, update the suspend and resume path to save and restore the
MSR C001_1004 value to ensure that the RDRAND CPUID setting remains in
place after resuming from suspend.
Note, that clearing the RDRAND CPUID bit does not prevent a processor
that normally supports the RDRAND instruction from executing it. So any
code that determined the support based on family and model won't #UD.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chen Yu <yu.c.chen@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@chromium.org> Cc: "linux-doc@vger.kernel.org" <linux-doc@vger.kernel.org> Cc: "linux-pm@vger.kernel.org" <linux-pm@vger.kernel.org> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: <stable@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "x86@kernel.org" <x86@kernel.org> Link: https://lkml.kernel.org/r/7543af91666f491547bd86cebb1e17c66824ab9f.1566229943.git.thomas.lendacky@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some newer machines do not advertise legacy timers. The kernel can handle
that situation if the TSC and the CPU frequency are enumerated by CPUID or
MSRs and the CPU supports TSC deadline timer. If the CPU does not support
TSC deadline timer the local APIC timer frequency has to be known as well.
Some Ryzens machines do not advertize legacy timers, but there is no
reliable way to determine the bus frequency which feeds the local APIC
timer when the machine allows overclocking of that frequency.
As there is no legacy timer the local APIC timer calibration crashes due to
a NULL pointer dereference when accessing the not installed global clock
event device.
Switch the calibration loop to a non interrupt based one, which polls
either TSC (if frequency is known) or jiffies. The latter requires a global
clockevent. As the machines which do not have a global clockevent installed
have a known TSC frequency this is a non issue. For older machines where
TSC frequency is not known, there is no known case where the legacy timers
do not exist as that would have been reported long ago.
Use 'lea' instead of 'add' when adjusting %rsp in CALL_NOSPEC so as to
avoid clobbering flags.
KVM's emulator makes indirect calls into a jump table of sorts, where
the destination of the CALL_NOSPEC is a small blob of code that performs
fast emulation by executing the target instruction with fixed operands.
adcb_al_dl:
0x000339f8 <+0>: adc %dl,%al
0x000339fa <+2>: ret
A major motiviation for doing fast emulation is to leverage the CPU to
handle consumption and manipulation of arithmetic flags, i.e. RFLAGS is
both an input and output to the target of CALL_NOSPEC. Clobbering flags
results in all sorts of incorrect emulation, e.g. Jcc instructions often
take the wrong path. Sans the nops...
ctxt->eflags = (ctxt->eflags & ~EFLAGS_MASK) | (flags & EFLAGS_MASK);
0x000359a8 <+136>: mov -0x10(%ebp),%eax
0x000359ab <+139>: and $0x8d5,%edi
0x000359b4 <+148>: and $0xfffff72a,%eax
0x000359b9 <+153>: or %eax,%edi
0x000359bd <+157>: mov %edi,0x4(%ebx)
For the most part this has gone unnoticed as emulation of guest code
that can trigger fast emulation is effectively limited to MMIO when
running on modern hardware, and MMIO is rarely, if ever, accessed by
instructions that affect or consume flags.
Breakage is almost instantaneous when running with unrestricted guest
disabled, in which case KVM must emulate all instructions when the guest
has invalid state, e.g. when the guest is in Big Real Mode during early
BIOS.
Fixes: 776b043848fd2 ("x86/retpoline: Add initial retpoline support") Fixes: 1a29b5b7f347a ("KVM: x86: Make indirect calls in emulator speculation safe") Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190822211122.27579-1-sean.j.christopherson@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver doesn't support open-drain/source config options, we
emulate this behavior when setting the direction by calling
gpiod_direction_input() if the default value is 0 (open-source) or
1 (open-drain), thus not actively driving the line in those cases.
This however clears the FLAG_IS_OUT bit for the GPIO line descriptor
and makes the LINEINFO ioctl() incorrectly report this line's mode as
'input' to user-space.
This commit modifies the ioctl() to always set the GPIOLINE_FLAG_IS_OUT
bit in the lineinfo structure's flags field. Since it's impossible to
use the input mode and open-drain/source options at the same time, we
can be sure the reported information will be correct.
Fixes: 521a2ad6f862 ("gpio: add userspace ABI for GPIO line information") Cc: stable <stable@vger.kernel.org> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Link: https://lore.kernel.org/r/20190806114151.17652-1-brgl@bgdev.pl Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 342406e4fbba ("drm/nouveau/i2c: Disable i2c bus access after
->fini()")
It turns out that while I did fix the error messages I was seeing on my
P50 when trying to access i2c busses with the GPU in runtime suspend, I
accidentally had missed one important detail that was mentioned on the
bug report this commit was supposed to fix: that the CPU would only lock
up when trying to access i2c busses _on connected devices_ _while the
GPU is not in runtime suspend_. Whoops. That definitely explains why I
was not able to get my machine to hang with i2c bus interactions until
now, as plugging my P50 into it's dock with an HDMI monitor connected
allowed me to finally reproduce this locally.
Now that I have managed to reproduce this issue properly, it looks like
the problem is much simpler then it looks. It turns out that some
connected devices, such as MST laptop docks, will actually ACK i2c reads
even if no data was actually read:
[ 275.063043] nouveau 0000:01:00.0: i2c: aux 000a: 1: 0000004c 1
[ 275.063447] nouveau 0000:01:00.0: i2c: aux 000a: 00 0110100010040000
[ 275.063759] nouveau 0000:01:00.0: i2c: aux 000a: rd 00000001
[ 275.064024] nouveau 0000:01:00.0: i2c: aux 000a: rd 00000000
[ 275.064285] nouveau 0000:01:00.0: i2c: aux 000a: rd 00000000
[ 275.064594] nouveau 0000:01:00.0: i2c: aux 000a: rd 00000000
Because we don't handle the situation of i2c ack without any data, we
end up entering an infinite loop in nvkm_i2c_aux_i2c_xfer() since the
value of cnt always remains at 0. This finally properly explains how
this could result in a CPU hang like the ones observed in the
aforementioned commit.
So, fix this by retrying transactions if no data is written or received,
and give up and fail the transaction if we continue to not write or
receive any data after 32 retries.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't rely on ->peer_features in calc_target() because it may be
called both when the OSD session is established and open and when it's
not. ->peer_features is not valid unless the OSD session is open. If
this happens on a PG split (pg_num increase), that could mean we don't
resend a request that should have been resent, hanging the client
indefinitely.
In userspace this was fixed by looking at require_osd_release and
get_xinfo[osd].features fields of the osdmap. However these fields
belong to the OSD section of the osdmap, which the kernel doesn't
decode (only the client section is decoded).
Instead, let's drop this feature check. It effectively checks for
luminous, so only pre-luminous OSDs would be affected in that on a PG
split the kernel might resend a request that should not have been
resent. Duplicates can occur in other scenarios, so both sides should
already be prepared for them: see dup/replay logic on the OSD side and
retry_attempt check on the client side.
Cc: stable@vger.kernel.org Fixes: 7de030d6b10a ("libceph: resend on PG splits if OSD has RESEND_ON_SPLIT") Link: https://tracker.ceph.com/issues/41162 Reported-by: Jerry Lee <leisurelysw24@gmail.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Tested-by: Jerry Lee <leisurelysw24@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ceph_mdsc_do_request returns an error, we can't assume that the
filelock_reply pointer will be set. Only try to fetch fields out of
the r_reply_info when it returns success.
Note that the fix offered by commit bd293d071ffe doesn't really prevent
the deadlock from occuring - if we look at the stacktrace reported by
Junxiao Bi, we see that it hangs in bit_wait_io and not on the mutex -
i.e. it has already successfully taken the mutex. Changing the mutex
from mutex_lock to mutex_trylock won't help with deadlocks that happen
afterwards.
Distance values reported by 2nd-gen Intuos tablets are on an inverted
scale (0 == far, 63 == near). We need to change them over to a normal
scale before reporting to userspace or else userspace drivers and
applications can get confused.
Ref: https://github.com/linuxwacom/input-wacom/issues/98 Fixes: eda01dab53 ("HID: wacom: Add four new Intuos devices") Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The events defined in pmu-events JSON are parsed and added into perf
tool. For fixed counters, we handle the encodings between JSON and perf
by using a static array fixed[].
But the fixed[] has missed an important event "cpu_clk_unhalted.core".
For example, on the Tremont platform,
[root@localhost ~]# perf stat -e cpu_clk_unhalted.core -a
event syntax error: 'cpu_clk_unhalted.core'
\___ parser error
With this patch, the event cpu_clk_unhalted.core can be parsed.
[root@localhost perf]# ./perf stat -e cpu_clk_unhalted.core -a -vvv
------------------------------------------------------------
perf_event_attr:
type 4
size 112
config 0x3c
sample_type IDENTIFIER
read_format TOTAL_TIME_ENABLED|TOTAL_TIME_RUNNING
disabled 1
inherit 1
exclude_guest 1
------------------------------------------------------------
...
Signed-off-by: Jin Yao <yao.jin@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20190729072755.2166-1-yao.jin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The buffer containing the string used to set cpumask is overwritten at
the end of the string later in cpu_map__snprint_mask due to not enough
memory space, when there is only one cpu.
And thus causes the following failure:
$ perf ftrace ls
failed to reset ftrace
$
This patch fixes the calculation of the cpumask string size.
Signed-off-by: He Zhe <zhe.he@windriver.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Fixes: dc23103278c5 ("perf ftrace: Add support for -a and -C option") Link: http://lkml.kernel.org/r/1564734592-15624-1-git-send-email-zhe.he@windriver.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when too many retries have occurred there is a memory
leak on the allocation for reply on the error return path. Fix
this by kfree'ing reply before returning.
Addresses-Coverity: ("Resource leak") Fixes: a9cd9c044aa9 ("drm/vmwgfx: Add a check to handle host message failure") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Deepak Rawat <drawat@vmware.com> Signed-off-by: Deepak Rawat <drawat@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with W=1, warnings about missing prototypes are emitted:
CC arch/x86/lib/cpu.o
arch/x86/lib/cpu.c:5:14: warning: no previous prototype for 'x86_family' [-Wmissing-prototypes]
5 | unsigned int x86_family(unsigned int sig)
| ^~~~~~~~~~
arch/x86/lib/cpu.c:18:14: warning: no previous prototype for 'x86_model' [-Wmissing-prototypes]
18 | unsigned int x86_model(unsigned int sig)
| ^~~~~~~~~
arch/x86/lib/cpu.c:33:14: warning: no previous prototype for 'x86_stepping' [-Wmissing-prototypes]
33 | unsigned int x86_stepping(unsigned int sig)
| ^~~~~~~~~~~~
Add the proper include file so the prototypes are there.
Abort processing of a command if we run out of mapped data in the
SG list. This should never happen, but a previous bug caused it to
be possible. Play it safe and attempt to abort nicely if we don't
have more SG segments left.
For passthrough requests, libata-scsi takes what the user passes in
as gospel. This can be problematic if the user fills in the CDB
incorrectly. One example of that is in request sizes. For read/write
commands, the CDB contains fields describing the transfer length of
the request. These should match with the SG_IO header fields, but
libata-scsi currently does no validation of that.
Check that the number of blocks in the CDB for passthrough requests
matches what was mapped into the request. If the CDB asks for more
data then the validated SG_IO header fields, error it.
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hip04_tx_reclaim is interrupted while it is running
and then __napi_schedule continues to execute
hip04_rx_poll->hip04_tx_reclaim, reentrancy occurs
and oops is generated. So you need to mask the interrupt
during the hip04_tx_reclaim run.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A call to 'kfree_skb()' is missing in the error handling path of
'init_one()'.
This is already present in 'remove_one()' but is missing here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some a4tech mice use the 'GenericDesktop.00b8' usage to inform whether
the previous wheel report was horizontal or vertical. Before c01908a14bf73 ("HID: input: add mapping for "Toggle Display" key") this
usage was being mapped to 'Relative.Misc'. After the patch it's simply
ignored (usage->type == 0 & usage->code == 0). Which ultimately makes
hid-a4tech ignore the WHEEL/HWHEEL selection event, as it has no
usage->type.
We shouldn't rely on a mapping for that usage as it's nonstandard and
doesn't really map to an input event. So we bypass the mapping and make
sure the custom event handling properly handles both reports.
John Hubbard reports seeing the following stack trace:
nfs4_do_reclaim
rcu_read_lock /* we are now in_atomic() and must not sleep */
nfs4_purge_state_owners
nfs4_free_state_owner
nfs4_destroy_seqid_counter
rpc_destroy_wait_queue
cancel_delayed_work_sync
__cancel_work_timer
__flush_work
start_flush_work
might_sleep:
(kernel/workqueue.c:2975: BUG)
The solution is to separate out the freeing of the state owners
from nfs4_purge_state_owners(), and perform that outside the atomic
context.
Reported-by: John Hubbard <jhubbard@nvidia.com> Fixes: 0aaaf5c424c7f ("NFS: Cache state owners after files are closed") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
strncpy() does not ensure NULL-termination when the input string
size equals to the destination buffer size 30.
The output string is passed to qed_int_deassertion_aeu_bit()
which calls DP_INFO() and relies NULL-termination.
Use strlcpy instead. The other conditional branch above strncpy()
needs no fix as snprintf() ensures NULL-termination.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string is
passed to dev_info() which relies on the NULL-termination.
Use strlcpy() instead.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string
'name' is passed to dev_info which relies on NULL-termination.
Use strlcpy() instead.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Juliana Rodrigueiro <juliana.rodrigueiro@intra2net.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Shijie Luo reported that when stress-testing ipset with multiple concurrent
create, rename, flush, list, destroy commands, it can result
ipset <version>: Broken LIST kernel message: missing DATA part!
error messages and broken list results. The problem was the rename operation
was not properly handled with respect of listing. The patch fixes the issue.
In start_isoc_chain(), usb_alloc_urb() on line 1392 may fail
and return NULL. At this time, fifo->iso[i].urb is assigned to NULL.
Then, fifo->iso[i].urb is used at some places, such as:
LINE 1405: fill_isoc_urb(fifo->iso[i].urb, ...)
urb->number_of_packets = num_packets;
urb->transfer_flags = URB_ISO_ASAP;
urb->actual_length = 0;
urb->interval = interval;
LINE 1416: fifo->iso[i].urb->...
LINE 1419: fifo->iso[i].urb->...
Thus, possible null-pointer dereferences may occur.
To fix these bugs, "continue" is added to avoid using fifo->iso[i].urb
when it is NULL.
These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hw_ver field was initialized to zero. Return the chip revision.
This is relevant for rdma driver.
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The BroadMobi BM818 M.2 card uses the QMI protocol
Signed-off-by: Bob Ham <bob.ham@puri.sm> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The slot_width is a property for the bus while the constraint for
SNDRV_PCM_HW_PARAM_SAMPLE_BITS is for the in memory format.
Applying slot_width constraint to sample_bits works most of the time, but
it will blacklist valid formats in some cases.
With slot_width 24 we can support S24_3LE and S24_LE formats as they both
look the same on the bus, but a a 24 constraint on sample_bits would not
allow S24_LE as it is stored in 32bits in memory.
Implement a simple hw_rule function to allow all formats which require less
or equal number of bits on the bus as slot_width (if configured).
devm_kzalloc may fail and return NULL. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_kzalloc may fail and return null. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the DAI format setup fails, there is no valid communication format
between CPU and CODEC, so fail card instantiation, rather than continue
with a card that will most likely not function properly.
CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.
Make sure the LED always reflects the state of the CAN device.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The following scenario was encountered during testing of logical
partition mobility on pseries partitions with bonded ibmvnic
adapters in LACP mode.
1. Driver receives a signal that the device has been
swapped, and it needs to reset to initialize the new
device.
2. Driver reports loss of carrier and begins initialization.
3. Bonding driver receives NETDEV_CHANGE notifier and checks
the slave's current speed and duplex settings. Because these
are unknown at the time, the bond sets its link state to
BOND_LINK_FAIL and handles the speed update, clearing
AD_PORT_LACP_ENABLE.
4. Driver finishes recovery and reports that the carrier is on.
5. Bond receives a new notification and checks the speed again.
The speeds are valid but miimon has not altered the link
state yet. AD_PORT_LACP_ENABLE remains off.
Because the slave's link state is still BOND_LINK_FAIL,
no further port checks are made when it recovers. Though
the slave devices are operational and have valid speed
and duplex settings, the bond will not send LACPDU's. The
simplest fix I can see is to force another speed check
in bond_miimon_commit. This way the bond will update
AD_PORT_LACP_ENABLE if needed when transitioning from
BOND_LINK_FAIL to BOND_LINK_UP.
CC: Jarod Wilson <jarod@redhat.com> CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
DPCM uses snd_soc_dapm_dai_get_connected_widgets to build a
list of the widgets connected to a specific front end DAI so it
can search through this list for available back end DAIs. The
custom_stop_condition was added to is_connected_ep to facilitate this
list not containing more widgets than is necessary. Doing so both
speeds up the DPCM handling as less widgets need to be searched and
avoids issues with CODEC to CODEC links as these would be confused
with back end DAIs if they appeared in the list of available widgets.
custom_stop_condition was implemented by aborting the graph walk
when the condition is triggered, however there is an issue with this
approach. Whilst walking the graph is_connected_ep should update the
endpoints cache on each widget, if the walk is aborted the number
of attached end points is unknown for that sub-graph. When the stop
condition triggered, the original patch ignored the triggering widget
and returned zero connected end points; a later patch updated this
to set the triggering widget's cache to 1 and return that. Both of
these approaches result in inaccurate values being stored in various
end point caches as the values propagate back through the graph,
which can result in later issues with widgets powering/not powering
unexpectedly.
As the original goal was to reduce the size of the widget list passed
to the DPCM code, the simplest solution is to limit the functionality
of the custom_stop_condition to the widget list. This means the rest
of the graph will still be processed resulting in correct end point
caches, but only widgets up to the stop condition will be added to the
returned widget list.
Fixes: 6742064aef7f ("ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets") Fixes: 5fdd022c2026 ("ASoC: dpcm: play nice with CODEC<->CODEC links") Fixes: 09464974eaa8 ("ASoC: dapm: Fix to return correct path list in is_connected_ep.") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20190718084333.15598-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In compat_do_replace(), a temporary buffer is allocated through vmalloc()
to hold entries copied from the user space. The buffer address is firstly
saved to 'newinfo->entries', and later on assigned to 'entries_tmp'. Then
the entries in this temporary buffer is copied to the internal kernel
structure through compat_copy_entries(). If this copy process fails,
compat_do_replace() should be terminated. However, the allocated temporary
buffer is not freed on this path, leading to a memory leak.
To fix the bug, free the buffer before returning from compat_do_replace().
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because CONFIG_OF defined for MIPS, cacheinfo attempts to fill information
from DT, ignoring data filled by architecture routine. This leads to error
reported
cacheinfo: Unable to detect cache hierarchy for CPU 0
Way to fix this provided in
commit fac51482577d ("drivers: base: cacheinfo: fix x86 with
CONFIG_OF enabled")
Utilize same mechanism to report that cacheinfo set by architecture
specific function
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Enable force feedback for the Thrustmaster Dual Trigger 2 in 1 Rumble Force
gamepad. Compared to other Thrustmaster devices, left and right rumble
motors here are swapped.
Kristian Evensen says:
In a project I am involved in, we are running ipsec (Strongswan) on
different mt7621-based routers. Each router is configured as an
initiator and has around ~30 tunnels to different responders (running
on misc. devices). Before the flow cache was removed (kernel 4.9), we
got a combined throughput of around 70Mbit/s for all tunnels on one
router. However, we recently switched to kernel 4.14 (4.14.48), and
the total throughput is somewhere around 57Mbit/s (best-case). I.e., a
drop of around 20%. Reverting the flow cache removal restores, as
expected, performance levels to that of kernel 4.9.
When pcpu xdst exists, it has to be validated first before it can be
used.
A negative hit thus increases cost vs. no-cache.
As number of tunnels increases, hit rate decreases so this pcpu caching
isn't a viable strategy.
Furthermore, the xdst cache also needs to run with BH off, so when
removing this the bh disable/enable pairs can be removed too.
Kristian tested a 4.14.y backport of this change and reported
increased performance:
In our tests, the throughput reduction has been reduced from around -20%
to -5%. We also see that the overall throughput is independent of the
number of tunnels, while before the throughput was reduced as the number
of tunnels increased.
When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
As commit 30d8177e8ac7 ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:
if (skb->encapsulation)
features &= dev->hw_enc_features;
clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8ac7 like this:
vlan_dev_hard_start_xmit
-->dev_queue_xmit
-->validate_xmit_skb
-->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
-->validate_xmit_vlan
-->__vlan_hwaccel_push_inside //skb->tci is cleared
...
--> bond_start_xmit
--> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
--> __skb_flow_dissect // nhoff point to IP header
--> case htons(ETH_P_8021Q)
// skb_vlan_tag_present is false, so
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
//vlan point to ip header wrongly
Fixes: b2a103e6d0af ("bonding: convert to ndo_fix_features") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should also enable team's vlan tx offload in hw_enc_features,
pass the vlan packets to the slave devices with vlan tci, let the
slave handle vlan tunneling offload implementation.
Fixes: 3268e5cb494d ("team: Advertise tunneling offload features") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ARFS code relies on certain fields to be set in the SKB
(e.g. transport_header) and extracts IP addresses and ports by custom
code that parses the packet. The necessary SKB fields, however, are not
always set at that point, which leads to an out-of-bounds access. Use
skb_flow_dissect_flow_keys() to get the necessary information reliably,
fix the out-of-bounds access and reuse the code.
At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mlx4_en_config_rss_steer(), 'rss_map->indir_qp' is allocated through
kzalloc(). After that, mlx4_qp_alloc() is invoked to configure RSS
indirection. However, if mlx4_qp_alloc() fails, the allocated
'rss_map->indir_qp' is not deallocated, leading to a memory leak bug.
To fix the above issue, add the 'qp_alloc_err' label to free
'rss_map->indir_qp'.
Fixes: 4931c6ef04b4 ("net/mlx4_en: Optimized single ring steering") Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 04f05230c5c13 ("bnx2x: Remove configured vlans as
part of unload sequence."), introduced a regression in driver
that as a part of VF's reload flow, VLANs created on the VF
doesn't get re-configured in hardware as vlan metadata/info
was not getting cleared for the VFs which causes vlan PING to stop.
This patch clears the vlan metadata/info so that VLANs gets
re-configured back in the hardware in VF's reload flow and
PING/traffic continues for VLANs created over the VFs.
Fixes: 04f05230c5c13 ("bnx2x: Remove configured vlans as part of unload sequence.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com> Signed-off-by: Shahed Shaikh <shshaikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log