The mlx4 driver will proxy MAD packets through the PF driver. A VM or an
instantiated VF will send its MAD packets to the PF driver using
loop-back. The PF driver will be informed by an interrupt, but defer the
handling and polling of CQEs to a worker thread running on an ordered
work-queue.
Consider the following scenario: the VMs will in short proximity in time,
for example due to a network event, send many MAD packets to the PF
driver. Lets say there are K VMs, each sending N packets.
The interrupt from the first VM will start the worker thread, which will
poll N CQEs. A common case here is where the PF driver will multiplex the
packets received from the VMs out on the wire QP.
But before the wire QP has returned a send CQE and associated interrupt,
the other K - 1 VMs have sent their N packets as well.
The PF driver has to multiplex K * N packets out on the wire QP. But the
send-queue on the wire QP has a finite capacity.
So, in this scenario, if K * N is larger than the send-queue capacity of
the wire QP, we will get MAD packets dropped on the floor with this
dynamic debug message:
mlx4_ib_multiplex_mad: failed sending GSI to wire on behalf of slave 2 (-11)
and this despite the fact that the wire send-queue could have capacity,
but the PF driver isn't aware, because the wire send CQEs have not yet
been polled.
We can also have a similar scenario inbound, with a wire recv-queue larger
than the tunnel QP's send-queue. If many remote peers send MAD packets to
the very same VM, the tunnel send-queue destined to the VM could allegedly
be construed to be full by the PF driver.
This starvation is fixed by introducing separate work queues for the wire
QPs vs. the tunnel QPs.
With this fix, using a dual ported HCA, 8 VFs instantiated, we could run
cmtime on each of the 18 interfaces towards a similar configured peer,
each cmtime instance with 800 QPs (all in all 14400 QPs) without a single
CM packet getting lost.
Currently __set_oom_adj loops through all processes in the system to keep
oom_score_adj and oom_score_adj_min in sync between processes sharing
their mm. This is done for any task with more that one mm_users, which
includes processes with multiple threads (sharing mm and signals).
However for such processes the loop is unnecessary because their signal
structure is shared as well.
Android updates oom_score_adj whenever a tasks changes its role
(background/foreground/...) or binds to/unbinds from a service, making it
more/less important. Such operation can happen frequently. We noticed
that updates to oom_score_adj became more expensive and after further
investigation found out that the patch mentioned in "Fixes" introduced a
regression. Using Pixel 4 with a typical Android workload, write time to
oom_score_adj increased from ~3.57us to ~362us. Moreover this regression
linearly depends on the number of multi-threaded processes running on the
system.
Mark the mm with a new MMF_MULTIPROCESS flag bit when task is created with
(CLONE_VM && !CLONE_THREAD && !CLONE_VFORK). Change __set_oom_adj to use
MMF_MULTIPROCESS instead of mm_users to decide whether oom_score_adj
update should be synchronized between multiple processes. To prevent
races between clone() and __set_oom_adj(), when oom_score_adj of the
process being cloned might be modified from userspace, we use
oom_adj_mutex. Its scope is changed to global.
The combination of (CLONE_VM && !CLONE_THREAD) is rarely used except for
the case of vfork(). To prevent performance regressions of vfork(), we
skip taking oom_adj_mutex and setting MMF_MULTIPROCESS when CLONE_VFORK is
specified. Clearing the MMF_MULTIPROCESS flag (when the last process
sharing the mm exits) is left out of this patch to keep it simple and
because it is believed that this threading model is rare. Should there
ever be a need for optimizing that case as well, it can be done by hooking
into the exit path, likely following the mm_update_next_owner pattern.
With the combination of (CLONE_VM && !CLONE_THREAD && !CLONE_VFORK) being
quite rare, the regression is gone after the change is applied.
[surenb@google.com: v3] Link: https://lkml.kernel.org/r/20200902012558.2335613-1-surenb@google.com Fixes: 44a70adec910 ("mm, oom_adj: make sure processes sharing mm have same view of oom_score_adj") Reported-by: Tim Murray <timmurray@google.com> Suggested-by: Michal Hocko <mhocko@kernel.org> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Eugene Syromiatnikov <esyr@redhat.com> Cc: Christian Kellner <christian@kellner.me> Cc: Adrian Reber <areber@redhat.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Aleksa Sarai <cyphar@cyphar.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Alexey Gladkov <gladkov.alexey@gmail.com> Cc: Michel Lespinasse <walken@google.com> Cc: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Andrei Vagin <avagin@gmail.com> Cc: Bernd Edlinger <bernd.edlinger@hotmail.de> Cc: John Johansen <john.johansen@canonical.com> Cc: Yafang Shao <laoar.shao@gmail.com> Link: https://lkml.kernel.org/r/20200824153036.3201505-1-surenb@google.com Debugged-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code in mc_handle_swap_pte() checks for non_swap_entry() and returns
NULL before checking is_device_private_entry() so device private pages are
never handled. Fix this by checking for non_swap_entry() after handling
device private swap PTEs.
I assume the memory cgroup accounting would be off somehow when moving
a process to another memory cgroup. Currently, the device private page
is charged like a normal anonymous page when allocated and is uncharged
when the page is freed so I think that path is OK.
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Ira Weiny <ira.weiny@intel.com> Link: https://lkml.kernel.org/r/20201009215952.2726-1-rcampbell@nvidia.com
xFixes: c733a82874a7 ("mm/memcontrol: support MEMORY_DEVICE_PRIVATE") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dump vlan tag and proto for the usual vlan offload case if the
NF_LOG_MACDECODE flag is set on. Without this information the logging is
misleading as there is no reference to the VLAN header.
Fixes: 83e96d443b37 ("netfilter: log: split family specific code to nf_log_{ip,ip6,common}.c files") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
fq qdisc requires tstamp to be cleared in forwarding path
Reported-by: Evgeny B <abt-admin@mail.ru> Link: https://bugzilla.kernel.org/show_bug.cgi?id=209427 Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Fixes: 8203e2d844d3 ("net: clear skb->tstamp in forwarding paths") Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC") Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.") Signed-off-by: Julian Anastasov <ja@ssi.bg> Reviewed-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
sdio.c:2403:3: warning: Attempt to free released memory
kfree(card->mpa_rx.buf);
^~~~~~~~~~~~~~~~~~~~~~~
When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again. If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().
So set both pointers to NULL when they are freed.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove PSU EEPROM configuration for systems class equipped with
Mellanox chip Spectrume-2. Till now all the systems from this class
used few types of power units, all equipped with EEPROM device with
address space two bytes. Thus, all these devices have been handled by
EEPROM driver "24c32".
There is a new requirement is to support power unit replacement by "off
the shelf" device, matching electrical required parameters. Such device
could be equipped with different EEPROM type, which could be one byte
address space addressing or even could be not equipped with EEPROM.
In such case "24c32" will not work.
Fixes: 1bd42d94ccab ("platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems") Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200923172053.26296-2-vadimp@nvidia.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The be_fill_queue() function can only fail when "eq_vaddress" is NULL and
since it's non-NULL here that means the function call can't fail. But
imagine if it could, then in that situation we would want to store the
"paddr" so that dma memory can be released.
Link: https://lore.kernel.org/r/20200928091300.GD377727@mwanda Fixes: bfead3b2cb46 ("[SCSI] be2iscsi: Adding msix and mcc_rings V3") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Corrects drivers/target/target_core_user.c:688:6: warning: 'page' may be
used uninitialized.
Link: https://lore.kernel.org/r/20200924001920.43594-1-john.p.donnelly@oracle.com Fixes: 3c58f737231e ("scsi: target: tcmu: Optimize use of flush_dcache_page") Cc: Mike Christie <michael.christie@oracle.com> Acked-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: John Donnelly <john.p.donnelly@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet
corresponds to single descriptor.
Descriptor limit set to mps and desc chain limit set to mps *
MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate
transfer size should be considered correction value for each descriptor.
In start request function, if "continue" is true then dma buffer address
should be incremmented by offset for all type of transfers, not only for
Control DATA_OUT transfers.
Fixes: cf77b5fb9b394 ("usb: dwc2: gadget: Transfer length limit checking for DDMA") Fixes: e02f9aa6119e0 ("usb: dwc2: gadget: EP 0 specific DDMA programming") Fixes: aa3e8bc81311e ("usb: dwc2: gadget: DDMA transfer start and complete") Signed-off-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When dumping wiphy information, we try to split the data into
many submessages, but for old userspace we still support the
old mode where this doesn't happen.
However, in this case we were not resetting our state correctly
and dumping multiple messages for each wiphy, which would have
broken such older userspace.
This was broken pretty much immediately afterwards because it
only worked in the original commit where non-split dumps didn't
have any more data than split dumps...
The u_ether driver has a qmult setting that multiplies the
transmit queue length (which by default is 2).
The intent is that it should be enabled at high/super speed, but
because the code does not explicitly check for USB_SUPER_PLUS,
it is disabled at that speed.
Fix this by ensuring that the queue multiplier is enabled for any
wired link at high speed or above. Using >= for USB_SPEED_*
constants seems correct because it is what the gadget_is_xxxspeed
functions do.
The queue multiplier substantially helps performance at higher
speeds. On a direct SuperSpeed Plus link to a Linux laptop,
iperf3 single TCP stream:
Before (qmult=1): 1.3 Gbps
After (qmult=5): 3.2 Gbps
Fixes: 04617db7aa68 ("usb: gadget: add SS descriptors to Ethernet gadget") Reviewed-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, SuperSpeed NCM gadgets report a speed of 851 Mbps
in USB_CDC_NOTIFY_SPEED_CHANGE. But the calculation appears to
assume 16 packets per microframe, and USB 3 and above no longer
use microframes.
Maximum speed is actually much higher. On a direct connection,
theoretical throughput is at most 3.86 Gbps for gen1x1 and
9.36 Gbps for gen2x1, and I have seen gadget->host iperf
throughput of >2 Gbps for gen1x1 and >4 Gbps for gen2x1.
Unfortunately the ConnectionSpeedChange defined in the CDC spec
only uses 32-bit values, so we can't report accurate numbers for
10Gbps and above. So, report 3.75Gbps for SuperSpeed (which is
roughly maximum theoretical performance) and 4.25Gbps for
SuperSpeed Plus (which is close to the maximum that we can report
in a 32-bit unsigned integer).
Chasing the callers of enic_dev_wait() revealed the gems of enic_reset()
and enic_tx_hang_reset() which are both invoked through work queues in
order to be able to call rtnl_lock(). So far so good.
After locking rtnl both functions acquire enic::enic_api_lock which
serializes against the (ab)use from infiniband. This is where the
trainwreck starts.
enic::enic_api_lock is a spin_lock() which implicitly disables preemption,
but both functions invoke a ton of functions under that lock which can
sleep. The BUG_ON(in_interrupt()) does not trigger in that case because it
can't detect the preempt disabled condition.
This clearly has never been tested with any of the mandatory debug options
for 7+ years, which would have caught that for sure.
Cure it by adding a enic_api_busy member to struct enic, which is modified
and evaluated with enic::enic_api_lock held.
If enic_api_devcmd_proxy_by_index() observes enic::enic_api_busy as true,
it drops enic::enic_api_lock and busy waits for enic::enic_api_busy to
become false.
It would be smarter to wait for a completion of that busy period, but
enic_api_devcmd_proxy_by_index() is called with other spin locks held which
obviously can't sleep.
Remove the BUG_ON(in_interrupt()) check as well because it's incomplete and
with proper debugging enabled the problem would have been caught from the
debug checks in schedule_timeout().
Fixes: 0b038566c0ea ("drivers/net: enic: Add an interface for USNIC to interact with firmware") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if an unsupported iftype is detected the error return path
does not free the cmd_skb leading to a resource leak. Fix this by
free'ing cmd_skb.
Addresses-Coverity: ("Resource leak") Fixes: 805b28c05c8e ("qtnfmac: prepare for AP_VLAN interface type support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200925132224.21638-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit 4f3882177240 hid-input started clearing of "ignored" usages
to avoid using garbage that might have been left in them. However
"battery strength" usages should not be ignored, as we do want to
use them.
Let the controller logic decide when to enter into clock pause mode!
Entering in to pause mode during unregistration does not really make
sense as the controller is totally going down at that point in time.
logical address can be either assigned by the SLIMBus controller or the core.
Core uses IDA in cases where get_addr callback is not provided by the
controller.
Core already has this check while allocating IDR, however during absence
reporting this is not checked. This patch fixes this issue.
Fixes: 498c60153ebb ("quota: Implement quota format with 64-bit space and inode limits") Link: https://lore.kernel.org/r/20200924183619.4176790-1-edumazet@google.com Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jan Kara <jack@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
CFI validates that all indirect calls go to a function with the same
exact function pointer prototype. In this case, dwc2_set_bcm_params
is the target, which has a parameter of type 'struct dwc2_hsotg *',
but it is being implicitly cast to have a parameter of type 'void *'
because that is the set_params function pointer prototype. Make the
function pointer protoype match the definitions so that there is no
more violation.
Recently we applied a fix to cover the whole OSS sequencer ioctls with
the mutex for dealing with the possible races. This works fine in
general, but in theory, this may lead to unexpectedly long stall if an
ioctl like SNDCTL_SEQ_SYNC is issued and an event with the far future
timestamp was queued.
For fixing such a potential stall, this patch changes the mutex lock
applied conditionally excluding such an ioctl command. Also, change
the mutex_lock() with the interruptible version for user to allow
escaping from the big-hammer mutex.
Inside __scif_pin_pages(), when map_flags != SCIF_MAP_KERNEL it
will call pin_user_pages_fast() to map nr_pages. However,
pin_user_pages_fast() might fail with a return value -ERRNO.
The return value is stored in pinned_pages->nr_pages. which in
turn is passed to unpin_user_pages(), which expects
pinned_pages->nr_pages >=0, else disaster.
Fix this by assigning pinned_pages->nr_pages to 0 if
pin_user_pages_fast() returns -ERRNO.
Fixes: ba612aa8b487 ("misc: mic: SCIF memory registration and unregistration") Cc: John Hubbard <jhubbard@nvidia.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Link: https://lore.kernel.org/r/1600570295-29546-1-git-send-email-jrdr.linux@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "tsid" is a user controlled u8 which comes from debugfs. Values
more than 15 are invalid because "active_tsids" is a 16 bit variable.
If the value of "tsid" is more than 31 then that leads to a shift
wrapping bug.
Fixes: 8fffd9e5ec9e ("ath6kl: Implement support for QOS-enable and QOS-disable from userspace") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200918142732.GA909725@mwanda Signed-off-by: Sasha Levin <sashal@kernel.org>
The VLANs and PVIDs on the RTL8366 utilizes a "member
configuration" (MC) which is largely unexplained in the
code.
This set-up requires a special ordering: rtl8366_set_pvid()
must be called first, followed by rtl8366_set_vlan(),
else the MC will not be properly allocated. Relax this
by factoring out the code obtaining an MC and reuse
the helper in both rtl8366_set_pvid() and
rtl8366_set_vlan() so we remove this strict ordering
requirement.
In the process, add some better comments and debug prints
so people who read the code understand what is going on.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rtl8366_set_vlan() and rtl8366_set_pvid() get invalid
VLANs tossed at it, especially VLAN0, something the hardware
and driver cannot handle. Check validity and bail out like
we do in the other callbacks.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
CONFIG_ARM_ARMADA_37XX_CPUFREQ is tristate option and therefore this
cpufreq driver can be compiled as a module. This patch adds missing
MODULE_DEVICE_TABLE which generates correct modalias for automatic
loading of this cpufreq driver when is compiled as an external module.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: 92ce45fb875d7 ("cpufreq: Add DVFS support for Armada 37xx")
[ Viresh: Added __maybe_unused ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.
Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.
Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On page 23 of the datasheet [0] it says "The register remains unchanged
until the interrupt is cleared via a read of INTCAP or GPIO." Include
INTCAPA and INTCAPB registers in precious range, so that they aren't
accidentally cleared when we read via debugfs.
The mcp23x17_regmap is initialised with structs named "mcp23x16".
However, the mcp23s08 driver doesn't support the MCP23016 device yet, so
this appears to be a typo.
Fixes: 8f38910ba4f6 ("pinctrl: mcp23s08: switch to regmap caching") Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20200828213226.1734264-2-thomas.preston@codethink.co.uk Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This code doesn't check if "settings->startup_profile" is within bounds
and that could result in an out of bounds array access. What the code
does do is it checks if the settings can be written to the firmware, so
it's possible that the firmware has a bounds check? It's safer and
easier to verify when the bounds checking is done in the kernel.
Fixes: 14bf62cde794 ("HID: add driver for Roccat Kone gaming mouse") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pixclock is being set locally because it is being passed as a
pass-by-value argument rather than pass-by-reference, so the computed
pixclock is never being set in var->pixclock. Fix this by passing
by reference.
[This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git ]
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@intel.com>
[b.zolnierkie: minor patch summary fixup]
[b.zolnierkie: removed "Fixes:" tag (not in upstream tree)] Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200723170227.996229-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.
But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.
When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:
base_unit &= (base_unit_range - 1);
But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.
This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit") Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit") Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
b6da31b2c07c "tty: Fix data race in tty_insert_flip_string_fixed_flag"
puts tty_flip_buffer_push under port->lock introducing the following
possible circular locking dependency:
[30129.876566] ======================================================
[30129.876566] WARNING: possible circular locking dependency detected
[30129.876567] 5.9.0-rc2+ #3 Tainted: G S W
[30129.876568] ------------------------------------------------------
[30129.876568] sysrq.sh/1222 is trying to acquire lock:
[30129.876569] ffffffff92c39480 (console_owner){....}-{0:0}, at: console_unlock+0x3fe/0xa90
[30129.876572] but task is already holding lock:
[30129.876572] ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca
[30129.876576] which lock already depends on the new lock.
[30129.876577] the existing dependency chain (in reverse order) is:
The code currently NULLs tty->driver_data in hvcs_close() with the
intent of informing the next call to hvcs_open() that device needs to be
reconfigured. However, when hvcs_cleanup() is called we copy hvcsd from
tty->driver_data which was previoulsy NULLed by hvcs_close() and our
call to tty_port_put(&hvcsd->port) doesn't actually do anything since
&hvcsd->port ends up translating to NULL by chance. This has the side
effect that when hvcs_remove() is called we have one too many port
references preventing hvcs_destuct_port() from ever being called. This
also prevents us from reusing the /dev/hvcsX node in a future
hvcs_probe() and we can eventually run out of /dev/hvcsX devices.
Fix this by waiting to NULL tty->driver_data in hvcs_cleanup().
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
In a couple of places in qp_host_get_user_memory(),
get_user_pages_fast() is called without properly checking for errors. If
e.g. -EFAULT is returned, this negative value will then be passed on to
qp_release_pages(), which expects a u64 as input.
Fix this by only calling qp_release_pages() when we have a positive
number returned.
When of_property_read_u32_array() returns an error code, a
pairing refcount decrement is needed to keep np's refcount
balanced.
Fixes: f705806c9f355 ("backlight: Add support Skyworks SKY81452 backlight driver") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reviewing this block of code in cdv_intel_dp_init()
ret = cdv_intel_dp_aux_native_read(gma_encoder, DP_DPCD_REV, ...
cdv_intel_edp_panel_vdd_off(gma_encoder);
if (ret == 0) {
/* if this fails, presume the device is a ghost */
DRM_INFO("failed to retrieve link info, disabling eDP\n");
drm_encoder_cleanup(encoder);
cdv_intel_dp_destroy(connector);
goto err_priv;
} else {
The (ret == 0) is not strict enough.
cdv_intel_dp_aux_native_read() returns > 0 on success
otherwise it is failure.
'rtl8192_irq_rx_tasklet()' is a tasklet initialized in
'rtl8192_init_priv_task()'.
>From this function it is possible to allocate some memory with the
GFP_KERNEL flag, which is not allowed in the atomic context of a tasklet.
Use GFP_ATOMIC instead.
The call chain is:
rtl8192_irq_rx_tasklet (in r8192U_core.c)
--> rtl8192_rx_nomal (in r8192U_core.c)
--> ieee80211_rx (in ieee80211/ieee80211_rx.c)
--> RxReorderIndicatePacket (in ieee80211/ieee80211_rx.c)
brcmfmac/core.c:490:4: warning: Dereference of null pointer
(*ifp)->ndev->stats.rx_errors++;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this block of code
if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && *ifp)
(*ifp)->ndev->stats.rx_errors++;
brcmu_pkt_buf_free_skb(skb);
return -ENODATA;
}
(*ifp)->ndev being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Fixes: 91b632803ee4 ("brcmfmac: Use net_device_stats from struct net_device") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200802161804.6126-1-trix@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
i2sctl register value is set to 0 during hw_free(). This
impacts any ongoing concurrent session on the same i2s
port. As trigger() stop already resets enable bit to 0,
there is no need of explicit hw_free. Removing it to
fix the issue.
Fixes: 80beab8e1d86 ("ASoC: qcom: Add LPASS CPU DAI driver") Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/1597402388-14112-7-git-send-email-rohitkr@codeaurora.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The value of "htc_hdr->endpoint_id" comes from skb->data so Smatch marks
it as untrusted so we have to check it before using it as an array
offset.
This is similar to a bug that syzkaller found in commit e4ff08a4d727
("ath9k: Fix use-after-free Write in ath9k_htc_rx_msg") so it is
probably a real issue.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200813141253.GA457408@mwanda Signed-off-by: Sasha Levin <sashal@kernel.org>
The value for "aid" comes from skb->data so Smatch marks it as
untrusted. If it's invalid then it can result in an out of bounds array
access in ath6kl_add_new_sta().
Fixes: 572e27c00c9d ("ath6kl: Fix AP mode connect event parsing and TIM updates") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200813141315.GB457408@mwanda Signed-off-by: Sasha Levin <sashal@kernel.org>
If hci_uart_tty_close() or hci_uart_unregister_device() is called while
hu->init_ready is scheduled, hci_register_dev() could be called after
the hci_uart is torn down. Avoid this by ensuring the work is complete
or canceled before checking the HCI_UART_REGISTERED flag.
Fixes: 9f2aee848fe6 ("Bluetooth: Add delayed init sequence support for UART controllers") Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.
example:
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 54995 ms
channel busy time: 432 ms
channel receive time: 0 ms
channel transmit time: 59 ms
...
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 32592 ms
channel busy time: 254 ms
channel receive time: 0 ms
channel transmit time: 0 ms
...
The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail to complete. This solution to the problem
is found in the vendor kernel for ARTIK5 boards based on Exynos3250.
When creating a new regulator its supply cannot create the sysfs link
because the device is not yet published. Remove early supply resolving
since it will be done later anyway. This makes the following error
disappear and the symlinks get created instead.
DCDC_REG1: supplied by VSYS
VSYS: could not add device link regulator.3 err -2
Note: It doesn't fix the problem for bypassed regulators, though.
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
And also, when the call of function vpe_runtime_get() failed,
we won't call vpe_runtime_put().
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails
inside vpe_runtime_get().
Fixes: 4571912743ac ("[media] v4l: ti-vpe: Add VPE mem to mem driver") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not
called in error handling paths. Thus replace the jump target
"err_release_buffers" by "err_pm_putw".
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Fixes: c5086f130a77 ("[media] s5p-mfc: Use clock gating only on MFC v5 hardware") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
PM runtime put is not called in error handling paths.
Thus call pm_runtime_put_sync() if pm_runtime_get_sync() fails.
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus call pm_runtime_put_noidle()
if pm_runtime_get_sync() fails.
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus call pm_runtime_put_noidle()
if pm_runtime_get_sync() fails.
Fixes: 90dedce9bc54 ("media: rcar-vin: add function to manipulate Gen3 chsel value") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
tc358743.c:1468:9: warning: Branch condition evaluates
to a garbage value
return handled ? IRQ_HANDLED : IRQ_NONE;
^~~~~~~
handled should be initialized to false.
Fixes: d747b806abf4 ("[media] tc358743: add direct interrupt handling") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the init loop, if an error occurs in function 'dma_alloc_coherent',
then goto the err_cleanup section, after run i--,
in the array ring, the struct mtk_ring with index i will not be released,
causing memory leaks
Fixes: 785e5c616c849 ("crypto: mediatek - Add crypto driver support for some MediaTek chips") Cc: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Xiaoliang Pang <dawning.pang@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting with MAX34451, the chips of this series support STATUS_IOUT and
STATUS_TEMPERATURE commands, and no longer report over-current and
over-temperature status with STATUS_MFR_SPECIFIC.
Fixes: 7a001dbab4ade ("hwmon: (pmbus/max34440) Add support for MAX34451.") Fixes: 50115ac9b6f35 ("hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461") Reported-by: Steve Foreman <foremans@google.com> Cc: Steve Foreman <foremans@google.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running export/import for hashes in peculiar order (mostly done by
openssl) can mess up the internal book keeping of the OMAP SHA core.
Fix by forcibly writing the correct DIGCNT back to hardware. This issue
was noticed while transitioning to openssl 1.1 support.
UBSAN reports a shift-out-of-bounds warning in uvc_get_le_value(). The
report is correct, but the issue should be harmless as the computed
value isn't used when the shift is negative. This may however cause
incorrect behaviour if a negative shift could generate adverse side
effects (such as a trap on some architectures for instance).
Regardless of whether that may happen or not, silence the warning as a
full WARN backtrace isn't nice.
Reported-by: Bart Van Assche <bvanassche@acm.org> Fixes: c0efd232929c ("V4L/DVB (8145a): USB Video Class driver") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Tested-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The media controller core prints a warning when an entity is registered
without a function being set. This affects the uvcvideo driver, as the
warning was added without first addressing the issue in existing
drivers. The problem is harmless, but unnecessarily worries users. Fix
it by mapping UVC entity types to MC entity functions as accurately as
possible using the existing functions.
Fixes: b50bde4e476d ("[media] v4l2-subdev: use MEDIA_ENT_T_UNKNOWN for new subdevs") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
m5mols_core.c:767:4: warning: Called function pointer
is null (null dereference) [core.CallAndMessage]
info->set_power(&client->dev, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In other places, the set_power ptr is checked.
So add a check.
Fixes: bc125106f8af ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "idle" pinctrl state is optional as documented in the DT binding.
The change introduced by the commit being reverted makes that pinctrl state
mandatory and breaks initialization of the whole media driver, since the
"idle" state is not specified in any mainline dts.
This reverts commit 18ffec750578 ("media: exynos4-is: Add missed check for pinctrl_lookup_state()")
to fix the regression.
tuner-simple.c:714:13: warning: Assigned value is
garbage or undefined
buffer[1] = buffer[3];
^ ~~~~~~~~~
In simple_set_radio_freq buffer[3] used to be done
in-function with a switch of tuner type, now done
by a call to simple_radio_bandswitch which has this case
case TUNER_TENA_9533_DI:
case TUNER_YMEC_TVF_5533MF:
tuner_dbg("This tuner doesn't ...
return 0;
which does not set buffer[3]. In the old logic, this case
would have returned 0 from simple_set_radio_freq.
Recover this old behavior by returning an error for this
codition. Since the old simple_set_radio_freq behavior
returned a 0, do the same.
Fixes: c7a9f3aa1e1b ("V4L/DVB (7129): tuner-simple: move device-specific code into three separate functions") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
engine->stat_irq_thresh was initialized after device_create_file() in
the probe function, the initialization may race with call to
spacc_stat_irq_thresh_store() which updates engine->stat_irq_thresh,
therefore initialize it before creating the file in probe function.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: ce92136843cb ("crypto: picoxcell - add support for the...") Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
I removed the MAY_BACKLOG flag on the aio path a while ago but
the error check still incorrectly interpreted EBUSY as success.
This may cause the submitter to wait for a request that will never
complete.
Fixes: dad419970637 ("crypto: algif_skcipher - Do not set...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
An incorrect sizeof is being used, struct attribute ** is not correct,
it should be struct attribute *. Note that since ** is the same size as
* this is not causing any issues. Improve this fix by using sizeof(*attrs)
as this allows us to not even reference the type of the pointer.
Addresses-Coverity: ("Sizeof not portable (SIZEOF_MISMATCH)") Fixes: 51686546304f ("x86/events/amd/iommu: Fix sysfs perf attribute groups") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20201001113900.58889-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When nmi_check_duration() is checking the time an NMI handler took to
execute, the whole_msecs value used should be read from the @duration
argument, not from the ->max_duration, the latter being used to store
the current maximal duration.
[ bp: Rewrite commit message. ]
Fixes: 248ed51048c4 ("x86/nmi: Remove irq_work from the long duration NMI handler") Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Libing Zhou <libing.zhou@nokia-sbell.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Changbin Du <changbin.du@gmail.com> Link: https://lkml.kernel.org/r/20200820025641.44075-1-libing.zhou@nokia-sbell.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This is due to use of an uninitialized local resource struct in the xgene
pmu driver. The thunderx2_pmu driver avoids this by using the resource list
constructed by acpi_dev_get_resources() rather than using a callback from
that function. The callback in the xgene driver didn't fully initialize
the resource. So get rid of the callback and search the resource list as
done by thunderx2.
Fixes: 832c927d119b ("perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver") Signed-off-by: Mark Salter <msalter@redhat.com> Link: https://lore.kernel.org/r/20200915204110.326138-1-msalter@redhat.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
0c2a3913d6f5 ("x86/fpu: Parse clearcpuid= as early XSAVE argument")
changed clearcpuid parsing from __setup() to cmdline_find_option().
While the __setup() function would have been called for each clearcpuid=
parameter on the command line, cmdline_find_option() will only return
the last one, so the change effectively made it impossible to disable
more than one bit.
Allow a comma-separated list of bit numbers as the argument for
clearcpuid to allow multiple bits to be disabled again. Log the bits
being disabled for informational purposes.
Also fix the check on the return value of cmdline_find_option(). It
returns -1 when the option is not found, so testing as a boolean is
incorrect.
platform_get_irq() returns a negative error number on error. In such a
case, comparison to 0 would pass the check therefore check the return
value properly, whether it is negative.
[ bp: Massage commit message. ]
Fixes: 86a18ee21e5e ("EDAC, ti: Add support for TI keystone and DRA7xx EDAC") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tero Kristo <t-kristo@ti.com> Link: https://lkml.kernel.org/r/20200827070743.26628-2-krzk@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When pci_get_device_func() fails, the driver doesn't need to execute
pci_dev_put(). mci should still be freed, though, to prevent a memory
leak. When pci_enable_device() fails, the error injection PCI device
"einj" doesn't need to be disabled either.
[ bp: Massage commit message, rename label to "bail_mc_free". ]
Fixes: 52608ba205461 ("i5100_edac: probe for device 19 function 0") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20200826121437.31606-1-dinghao.liu@zju.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
The async path cannot use MAY_BACKLOG because it is not meant to
block, which is what MAY_BACKLOG does. On the other hand, both
the sync and async paths can make use of MAY_SLEEP.
Fixes: 83094e5e9e49 ("crypto: af_alg - add async support to...") Cc: <stable@vger.kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Errors returned by crypto_shash_update() are not checked in
ima_calc_boot_aggregate_tfm() and thus can be overwritten at the next
iteration of the loop. This patch adds a check after calling
crypto_shash_update() and returns immediately if the result is not zero.
Cc: stable@vger.kernel.org Fixes: 3323eec921efd ("integrity: IMA as an integrity service provider") Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function amd_ir_set_vcpu_affinity makes use of the parameter struct
amd_iommu_pi_data.prev_ga_tag to determine if it should delete struct
amd_iommu_pi_data from a list when not running in AVIC mode.
However, prev_ga_tag is initialized only when AVIC is enabled. The non-zero
uninitialized value can cause unintended code path, which ends up making
use of the struct vcpu_svm.ir_list and ir_list_lock without being
initialized (since they are intended only for the AVIC case).
This triggers NULL pointer dereference bug in the function vm_ir_list_del
with the following call trace:
Call kvm_mmu_commit_zap_page() after exiting the "prepare zap" loop in
kvm_recover_nx_lpages() to finish zapping pages in the unlikely event
that the loop exited due to lpage_disallowed_mmu_pages being empty.
Because the recovery thread drops mmu_lock() when rescheduling, it's
possible that lpage_disallowed_mmu_pages could be emptied by a different
thread without to_zap reaching zero despite to_zap being derived from
the number of disallowed lpages.
Fixes: 1aa9b9572b105 ("kvm: x86: mmu: Recovery of shattered NX large pages") Cc: Junaid Shahid <junaids@google.com> Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-2-sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log