The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control") Cc: stable <stable@vger.kernel.org> # 4.18 Cc: Florian Zumbiehl <florz@florz.de> Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
team_notify_peers() will send ARP and NA to notify peers. team_mcast_rejoin()
will send multicast join group message to notify peers. We should do this when
enabling/changed to a new port. But it doesn't make sense to do it when a port
is disabled.
On the other hand, when we set mcast_rejoin_count to 2, and do a failover,
team_port_disable() will increase mcast_rejoin.count_pending to 2 and then
team_port_enable() will increase mcast_rejoin.count_pending to 4. We will send
4 mcast rejoin messages at latest, which will make user confused. The same
with notify_peers.count.
Fix it by deleting team_notify_peers() and team_mcast_rejoin() in
team_port_disable().
Reported-by: Liang Li <liali@redhat.com> Fixes: fc423ff00df3a ("team: add peer notification") Fixes: 492b200efdd20 ("team: add support for sending multicast rejoins") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
During device reset, queue memory is not being updated to accommodate
changes in ring buffer sizes supported by backing hardware. Track
any differences in ring buffer sizes following the reset and update
queue memory when possible.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The wrong index is used when cleaning up RX buffer objects during release
of RX queues. Update to use the correct index counter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bruce pointed out that we shouldn't allocate memory while holding
a lock in the nfs4_callback_offload() and handle_async_copy()
that deal with a racing CB_OFFLOAD and reply to COPY case.
In the original ftmac100_interrupt(), the interrupts are only disabled when
the condition "netif_running(netdev)" is true. However, this condition
causes kerenl hang in the following case. When the user requests to
disable the network device, kernel will clear the bit __LINK_STATE_START
from the dev->state and then call the driver's ndo_stop function. Network
device interrupts are not blocked during this process. If an interrupt
occurs between clearing __LINK_STATE_START and stopping network device,
kernel cannot disable the interrupts due to the condition
"netif_running(netdev)" in the ISR. Hence, kernel will hang due to the
continuous interruption of the network device.
In order to solve the above problem, the interrupts of the network device
should always be disabled in the ISR without being restricted by the
condition "netif_running(netdev)".
[V2]
Remove unnecessary curly braces.
Signed-off-by: Vincent Chen <vincentc@andestech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.
Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.
The patch consists of 3 fixes:
- When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
returned PQ 0, which can potentially be another function's pq. Verify
that flag is enabled, otherwise return default start_pq.
- When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
returned NULL and could lead to a segmentation fault. Return default
start_pq instead.
- A modulo operation was added to MCOS/VFS PQ getters to make sure the
PQ returned is in range of the required flag.
Fixes: b5a9ee7cf3be ("qed: Revise QM cofiguration") Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a deadlock whereby the NFSv4 state manager can get stuck in the
delegation return code, waiting for a layout return to complete in
another thread. If the server reboots before that other thread
completes, then we need to be able to start a second state
manager thread in order to perform recovery.
During resume from hibernation if ena_restore_device fails,
ena_com_dev_reset() is called, and uses the readless read mechanism,
which was already destroyed by the call to
ena_com_mmio_reg_read_request_destroy(). This causes a NULL pointer
reference.
In this commit we switch the call order of the above two functions
to avoid this crash.
Fixes: d7703ddbd7c9 ("net: ena: fix rare bug when failed restart/resume is followed by driver removal") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current Cadence QSPI driver caused a kernel panic sporadically
when writing to QSPI. The problem was caused by writing more bytes
than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 11.202044] Unable to handle kernel paging request at virtual address bffd3000
[ 11.209254] pgd = e463054d
[ 11.211948] [bffd3000] *pgd=2fffb811, *pte=00000000, *ppte=00000000
[ 11.218202] Internal error: Oops: 7 [#1] SMP ARM
[ 11.222797] Modules linked in:
[ 11.225844] CPU: 1 PID: 1317 Comm: systemd-hwdb Not tainted 4.17.7-d0c45cd44a8f
[ 11.235796] Hardware name: Altera SOCFPGA Arria10
[ 11.240487] PC is at __raw_writesl+0x70/0xd4
[ 11.244741] LR is at cqspi_write+0x1a0/0x2cc
</snip>
On a page boundary limit the number of bytes copied from the tx buffer
to remain within the page.
This patch uses a temporary buffer to hold the 4 bytes to write and then
copies only the bytes required from the tx buffer.
Reported-by: Adrian Amborzewicz <adrian.ambrozewicz@intel.com> Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Please note that `strlcpy()` does *NOT* do what you think it does.
strlcpy() *ALWAYS* reads the full input string, regardless of the
'length' parameter. That is, if the input is not zero-terminated,
strlcpy() will *READ* beyond input boundaries. It does this, because it
always returns the size it *would* copy if the target was big enough,
not the truncated size it actually copied.
The original code was perfectly fine. The hid device is
zero-initialized and the strncpy() functions copied up to n-1
characters. The result is always zero-terminated this way.
This is the third time someone tried to replace strncpy with strlcpy in
this function, and gets it wrong. I now added a comment that should at
least make people reconsider.
Currently the ti-cpufreq driver blindly registers a 'ti-cpufreq' to force
the driver to probe on any platforms where the driver is built in.
However, this should only happen on platforms that actually can make use
of the driver. There is already functionality in place to match the
SoC compatible so let's factor this out into a separate call and
make sure we find a match before creating the ti-cpufreq platform device.
Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Caught by riscv allmodconfig.
Signed-off-by: Olof Johansson <olof@lixom.net> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add some defensive coding in case one of the subprocesses created by tdc
returns nothing. If no object is returned from exec_cmd, then tdc will
halt with an unhandled exception.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com> Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Prevent exceptions from being raised while decoding output
from an executed command. There is no impact on tdc's
execution and the verify command phase would fail the pattern
match.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3edfb7bd76bd ("gpiolib: Show correct direction from the
beginning") fixed an existing issue but broke libgpiod tests by
changing the default direction of dummy lines to output.
We don't break user-space so make gpio-mockup behave as before.
As pointed out by Gregor, spitz keyboard matrix is broken, with or
without CONFIG_PINCTRL set, quoting :
"The gpio matrix keypard on the Zaurus C3x00 (see spitz.c) does not work
properly. Noticeable are that rshift+c does nothing where as lshift+c
creates C. Opposite it is for rshift+a vs lshift+a, here only rshift
works. This affects a few other combinations using the rshift or lshift
buttons."
As a matter of fact, as for platform_data based builds CONFIG_PINCTRL=n
is required for now (as opposed for devicetree builds where it should be
set), this means gpio driver should change the direction, which is what
was attempted by commit c4e5ffb6f224 ("gpio: pxa: fix legacy non pinctrl
aware builds").
Unfortunately, the input case was inverted, and the direction change was
never done. This wasn't seen up until now because the initial platform
setup (MFP) was setting this direction. Yet in Gregory's case, the
matrix-keypad driver changes back and forth the direction dynamically,
and this is why he's the first to report it.
Fixes: 291d57f67d244973 ("qed: Fix rdma_info structure allocation") Cc: Michal Kalderon <michal.kalderon@cavium.com> Cc: Denis Bolotin <denis.bolotin@cavium.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
UBSAN: Undefined behavior in
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:626:29
signed integer overflow: 1802201963 + 1802201963 cannot be represented
in type 'int'
The union of res_reserved and res_port_rsvd[MLX4_MAX_PORTS] monitors
granting of reserved resources. The grant operation is calculated and
protected, thus both members of the union cannot be negative. Changed
type of res_reserved and of res_port_rsvd[MLX4_MAX_PORTS] from signed
int to unsigned int, allowing large value.
Fixes: 5a0d0a6161ae ("mlx4: Structures and init/teardown for VF resource quotas") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize the uid variable to zero to avoid the compilation warning.
Fixes: 7a89399ffad7 ("net/mlx4: Add mlx4_bitmap zone allocator") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When re-registering a user mr, the mpt information for the
existing mr when running SRIOV is obtained via the QUERY_MPT
fw command. The returned information includes the mpt's lkey.
This retrieved mpt information is used to move the mpt back
to hardware ownership in the rereg flow (via the SW2HW_MPT
fw command when running SRIOV).
The fw API spec states that for SW2HW_MPT, the lkey field
must be zero. Any ConnectX-3 PF driver which checks for strict spec
adherence will return failure for SW2HW_MPT if the lkey field is not
zero (although the fw in practice ignores this field for SW2HW_MPT).
Thus, in order to conform to the fw API spec, set the lkey field to zero
before invoking SW2HW_MPT when running SRIOV.
Fixes: e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.
Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.
This should be a user configurable option such that the user can select
what bpc configuration they would like.
[How]
This patch adds support for getting and setting the amdgpu driver
specific "max bpc" property on the connector.
It also adds support for limiting the output bpc based on the property
value. The default limitation is the lowest value in the range, 8bpc.
This was the old value before the range was uncapped.
This patch should be updated/replaced later once common drm support
for max bpc lands.
Bugzilla: https://bugs.freedesktop.org/108542
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201585
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200645 Fixes: e03fd3f300f6 ("drm/amd/display: Do not limit color depth to 8bpc")
v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.
Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.
This should be a user configurable option such that the user can select
what bpc configuration they would like.
[How]
This patch introduces the "max bpc" amdgpu driver specific connector
property so the user can limit the maximum bpc. It ranges from 8 to 16.
This doesn't directly set the preferred bpc for the panel since it
follows Intel's existing driver conventions.
This proprety should be removed once common drm support for max bpc
lands.
v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the year and month offset while storing it in
bnxt_fill_coredump_record().
Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an io error occurs on an io issued while connecting, recovery
of the io falls flat as the state checking ends up nooping the error
handler.
Create an err_work work item that is scheduled upon an io error while
connecting. The work thread terminates all io on all queues and marks
the queues as not connected. The termination of the io will return
back to the callee, which will then back out of the connection attempt
and will reschedule, if possible, the connection attempt.
The changes:
- in case there are several commands hitting the error handler, a
state flag is kept so that the error work is only scheduled once,
on the first error. The subsequent errors can be ignored.
- The calling sequence to stop keep alive and terminate the queues
and their io is lifted from the reset routine. Made a small
service routine used by both reset and err_work.
- During debugging, found that the teardown path can reference
an uninitialized pointer, resulting in a NULL pointer oops.
The aen_ops weren't initialized yet. Add validation on their
initialization before calling the teardown routine.
Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
SMC-D stress workload showed connection stalls. Since the firmware
decides to skip raising an interrupt if the SBA DMBE mask bit is
still set, this SBA DMBE mask bit should be cleared before the
IRQ handling in the SMC code runs. Otherwise there are small windows
possible with missing interrupts for incoming data.
SMC-D currently does not care about the old value of the SBA DMBE
mask.
Acked-by: Sebastian Ott <sebott@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The value of "sb_index" is written by the hardware. Reading its value and
writing it to "index" must finish before checking the loop condition.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Certain flows need to access the rdma-info structure, for example dcbx
update flows. In some cases there can be a race between the allocation or
deallocation of the structure which was done in roce start / roce stop and
an asynchrounous dcbx event that tries to access the structure.
For this reason, we move the allocation of the rdma_info structure to be
similar to the iscsi/fcoe info structures which are allocated during device
setup.
We add a new field of "active" to the struct to define whether roce has
already been started or not, and this is checked instead of whether the
pointer to the info structure.
Fixes: 51ff17251c9c ("qed: Add support for RoCE hw init") Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TC received from APP TLV is stored in offload_tc, and should not be
set by protocols which did not receive an APP TLV. Fixed the condition
when overriding the offload_tc.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com> Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver assigns DMAE channel 0 for FW as part of START_RAMROD command. FW
uses this channel for DMAE operations (e.g., TIME_SYNC implementation).
Driver also uses the same channel 0 for DMAE operations for some of the PFs
(e.g., PF0 on Port0). This could lead to concurrent access to the DMAE
channel by FW and driver which is not legal. Hence need to assign unique
DMAE id for FW.
Currently following DMAE channels are used by the clients,
MFW - OCBB/OCSD functionality uses DMAE channel 14/15
Driver 0-3 and 8-11 (for PF dmae operations)
4 and 12 (for stats requests)
Assigning unique dmae_id '13' to the FW.
Changes from previous version:
------------------------------
v2: Incorporated the review comments.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This register should have been programmed with the physical address
of the memory location containing the shadow tail pointer for
the guest virtual APIC log instead of the base address.
The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge") Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net> Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
The Motorola/Zebra Symbol DS4308-HD is a handheld USB barcode scanner
which does not have a battery, but reports one anyway that always has
capacity 2.
Let's apply the IGNORE quirk to prevent it from being treated like a
power supply so that userspaces don't get confused that this
accessory is almost out of power and warn the user that they need to charge
their wired barcode scanner.
In the case where eq->fw->size > PAGE_SIZE the error return rc
is being set to EINVAL however this is being overwritten to
rc = req->fw->size because the error exit path via label 'out' is
not being taken. Fix this by adding the jump to the error exit
path 'out'.
Detected by CoverityScan, CID#1453465 ("Unused value")
Fixes: c92316bf8e94 ("test_firmware: add batched firmware tests") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes: 862e2b6af9413b43 ("can: rcar_can: support all input clocks") Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
struct usb_device *udev;
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hynix ufs has deviations on hi36xx platform which will result in ufs bursts
transfer failures.
To fix the problem, the Hynix device must set the register
VS_DebugSaveConfigTime to 0x10, which will set time reference for
SaveConfigTime is 250 ns. The time reference for SaveConfigTime is 40 ns by
default.
This patch is necessary to boot on HiKey960 boards that use Hynix UFS chips
(H28U62301AMR model: hB8aL1).
Cc: Vinayak Holikatti <vinholikatti@gmail.com> Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Signed-off-by: Wei Li <liwei213@huawei.com> Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
[jstultz: Forward ported from older code, slight tweak to commit message] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_LEDS_CLASS is disabled, or it is a loadable module while
mt76 is built-in, we run into a link error:
drivers/net/wireless/mediatek/mt76/mac80211.o: In function `mt76_register_device':
mac80211.c:(.text+0xb78): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_of_led_classdev_register'
We don't really need a hard dependency here as the driver can presumably
work just fine without LEDs, so this follows the iwlwifi example and
adds a separate Kconfig option for the LED support, this will be available
whenever it will link, and otherwise the respective code gets left out from
the driver object.
Fixes: 17f1de56df05 ("mt76: add common code shared between multiple chipsets") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.
This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
Before: chnum:50 control_ch_num:36
After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
Before: chnum:114 control_ch_num:100
After: chnum:114 control_ch_num:120
Fixes: 330994e8e8ec ("brcmfmac: fix for proper support of 160MHz bandwidth") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While there are issues related to object lifetime management, unregister
the media device first, followed immediately by other device nodes when
the driver is being unbound. Only then the resources needed by the driver
may be released. This is slightly safer.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by: Bingbu Cao <bingbu.cao@intel.com> Reviewed-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While there are issues related to object lifetime management, unregister the
media device first when the driver is being unbound. This is slightly
safer.
After the direct dispatch corruption fix, we permanently disallow direct
dispatch of non read/write requests. This works fine off the normal IO
path, as they will be retried like any other failed direct dispatch
request. But for the blk_insert_cloned_request() that only DM uses to
bypass the bottom level scheduler, we always first attempt direct
dispatch. For some types of requests, that's now a permanent failure,
and no amount of retrying will make that succeed. This results in a
livelock.
Instead of making special cases for what we can direct issue, and now
having to deal with DM solving the livelock while still retaining a BUSY
condition feedback loop, always just add a request that has been through
->queue_rq() to the hardware queue dispatch list. These are safe to use
as no merging can take place there. Additionally, if requests do have
prepped data from drivers, we aren't dependent on them not sharing space
in the request structure to safely add them to the IO scheduler lists.
This basically reverts ffe81d45322c and is based on a patch from Ming,
but with the list insert case covered as well.
Fixes: ffe81d45322c ("blk-mq: fix corruption with direct issue") Cc: stable@vger.kernel.org Suggested-by: Ming Lei <ming.lei@redhat.com> Reported-by: Bart Van Assche <bvanassche@acm.org> Tested-by: Ming Lei <ming.lei@redhat.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net/tipc/topsrv.c: In function ‘tipc_topsrv_start’:
net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=]
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/topsrv.c:660:27: note: length computed here
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~
So change it to correct length and use strscpy.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default NFSv3 doesn't support ACL (Access Control Lists)
which might be quite convenient to have so that
mounted NFS behaves exactly as any other local file-system.
In particular missing support of ACL makes umask useless.
This among other thigs fixes Glibc's "nptl/tst-umask1".
Change the default defconfig (used with 'make defconfig') to the ARCv2
nsim_hs_defconfig, and also switch the default Kconfig ISA selection to
ARCv2.
This allows several default defconfigs (e.g. make defconfig, make
allnoconfig, make tinyconfig) to all work with ARCv2 by default.
Note since we change default architecture from ARCompact to ARCv2
it's required to explicitly mention architecture type in ARCompact
defconfigs otherwise ARCv2 will be implied and binaries will be
generated for ARCv2.
[BUG]
A completely valid btrfs will refuse to mount, with error message like:
BTRFS critical (device sdb2): corrupt leaf: root=2 block=239681536 slot=172 \
bg_start=12018974720 bg_len=10888413184, invalid block group size, \
have 10888413184 expect (0, 10737418240]
This has been reported several times as the 4.19 kernel is now being
used. The filesystem refuses to mount, but is otherwise ok and booting
4.18 is a workaround.
Btrfs check returns no error, and all kernels used on this fs is later
than 2011, which should all have the 10G size limit commit.
[CAUSE]
For a 12 devices btrfs, we could allocate a chunk larger than 10G due to
stripe stripe bump up.
The cros_ec_keyb_bs array lists buttons and switches together, expecting
that its users will match the appropriate type and bit fields. But
cros_ec_keyb_register_bs() only checks the 'bit' field, which causes
misreported input capabilities in some cases. For example, tablets
(e.g., Scarlet -- a.k.a. Acer Chromebook Tab 10) were reporting a SW_LID
capability, because EC_MKBP_POWER_BUTTON and EC_MKBP_LID_OPEN happen to
share the same bit.
(This has comedic effect on a tablet, in which a power-management daemon
then thinks this "lid" is closed, and so puts the system to sleep as
soon as it boots!)
To fix this, check both the 'ev_type' and 'bit' fields before reporting
the capability.
Tested with a lid (Kevin / Samsung Chromebook Plus) and without a lid
(Scarlet / Acer Chromebook Tab 10).
This error got introduced when porting the feature from the downstream
Chromium OS kernel to be upstreamed.
"of_get_named_gpio()" returns a negative error value if it fails
and drivers should check for this. This missing check was now
added to the matrix_keypad driver.
In my case "of_get_named_gpio()" returned -EPROBE_DEFER because
the referenced GPIOs belong to an I/O expander, which was not yet
probed at the point in time when the matrix_keypad driver was
loading. Because the driver did not check for errors from the
"of_get_named_gpio()" routine, it was assuming that "-EPROBE_DEFER"
is actually a GPIO number and continued as usual, which led to further
errors like this later on:
Note that the "GPIO number" -517 in the error message above is
actually "-EPROBE_DEFER".
As part of the patch a misleading error message "no platform data defined"
was also removed. This does not lead to information loss because the other
error paths in matrix_keypad_parse_dt() already print an error.
Signed-off-by: Christian Hoff <christian_hoff@gmx.net> Suggested-by: Sebastian Reichel <sre@kernel.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noticed the other day the trackpoint felt different on my P50, then
realized it was because rmi4 wasn't loading for this machine
automatically. Suspend/resume, hibernate, and everything else seem to
work perfectly fine on here.
Since f44ac12f1dcc, BG enablement is tracked with the LPFC_SLI3_BG_ENABLED
bit, which is set in lpfc_get_cfgparam before lpfc_sli_config_sli_port() is
called. The bit shouldn't be cleared before checking the feature. Based on
problem analysis by David Bond.
Fixes: f44ac12f1dcc "scsi: lpfc: Memory allocation error during driver start-up on power8" Tested-by: David Bond <dbond@suse.com> Signed-off-by: Martin Wilck <mwilck@suse.com> Cc: stable@vger.kernel.org # 4.17.x Cc: stable@vger.kernel.org # 4.18.x Cc: stable@vger.kernel.org # 4.19.x Reviewed-by: Hannes Reinecke <hare@suse.com> Acked-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.
CC: stable <stable@vger.kernel.org> Signed-off-by: Lihong Yang <lihong.yang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 32a4f5ecd738 ("net: sched: introduce chain object to uapi")
added new RTM_* definitions without properly updating SELinux, this
patch adds the necessary SELinux support.
While there was a BUILD_BUG_ON() in the SELinux code to protect from
exactly this case, it was bypassed in the broken commit. In order to
hopefully prevent this from happening in the future, add additional
comments which provide some instructions on how to resolve the
BUILD_BUG_ON() failures.
Fixes: 32a4f5ecd738 ("net: sched: introduce chain object to uapi") Cc: <stable@vger.kernel.org> # 4.19 Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition when accessing kvm->arch.apic_access_page_done.
Due to it, x86_set_memory_region will fail when creating the second vcpu
for a svm guest.
Add a mutex_lock to serialize the accesses to apic_access_page_done.
This lock is also used by vmx for the same purpose.
After 2dd453168643 ("kgdboc: Fix restrict error"), kgdboc_option_setup is
now only used when built in, resulting in a warning when compiled as a
module:
drivers/tty/serial/kgdboc.c:134:12: warning: 'kgdboc_option_setup' defined but not used [-Wunused-function]
static int kgdboc_option_setup(char *opt)
^~~~~~~~~~~~~~~~~~~
Move the function under the appropriate ifdef for builtin only.
Fixes: 2dd453168643 ("kgdboc: Fix restrict error") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/kgdboc.c: In function ‘configure_kgdboc’:
drivers/tty/serial/kgdboc.c:137:2: error: ‘strcpy’ source argument is the same
as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error implies, this is from trying to use config as both source and
destination. Drop the call to the function where config is the argument
since nothing else happens in the function.
Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the page dirty if VM_WRITE is not set because in such case the pte
won't be marked dirty and the page would be reclaimed without writepage
(i.e. swapout in the shmem case).
This was found by source review. Most apps (certainly including QEMU)
only use UFFDIO_COPY on PROT_READ|PROT_WRITE mappings or the app can't
modify the memory in the first place. This is for correctness and it
could help the non cooperative use case to avoid unexpected data loss.
Link: http://lkml.kernel.org/r/20181126173452.26955-6-aarcange@redhat.com Reviewed-by: Hugh Dickins <hughd@google.com> Cc: stable@vger.kernel.org Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Reported-by: Hugh Dickins <hughd@google.com> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With MAP_SHARED: recheck the i_size after taking the PT lock, to
serialize against truncate with the PT lock. Delete the page from the
pagecache if the i_size_read check fails.
With MAP_PRIVATE: check the i_size after the PT lock before mapping
anonymous memory or zeropages into the MAP_PRIVATE shmem mapping.
A mostly irrelevant cleanup: like we do the delete_from_page_cache()
pagecache removal after dropping the PT lock, the PT lock is a spinlock
so drop it before the sleepable page lock.
Link: http://lkml.kernel.org/r/20181126173452.26955-5-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Reported-by: Jann Horn <jannh@google.com> Cc: <stable@vger.kernel.org> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userfaultfd did not create private memory when UFFDIO_COPY was invoked
on a MAP_PRIVATE shmem mapping. Instead it wrote to the shmem file,
even when that had not been opened for writing. Though, fortunately,
that could only happen where there was a hole in the file.
Fix the shmem-backed implementation of UFFDIO_COPY to create private
memory for MAP_PRIVATE mappings. The hugetlbfs-backed implementation
was already correct.
This change is visible to userland, if userfaultfd has been used in
unintended ways: so it introduces a small risk of incompatibility, but
is necessary in order to respect file permissions.
An app that uses UFFDIO_COPY for anything like postcopy live migration
won't notice the difference, and in fact it'll run faster because there
will be no copy-on-write and memory waste in the tmpfs pagecache
anymore.
Userfaults on MAP_PRIVATE shmem keep triggering only on file holes like
before.
The real zeropage can also be built on a MAP_PRIVATE shmem mapping
through UFFDIO_ZEROPAGE and that's safe because the zeropage pte is
never dirty, in turn even an mprotect upgrading the vma permission from
PROT_READ to PROT_READ|PROT_WRITE won't make the zeropage pte writable.
Link: http://lkml.kernel.org/r/20181126173452.26955-3-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jann found two bugs in the userfaultfd shmem MAP_SHARED backend: the
lack of the VM_MAYWRITE check and the lack of i_size checks.
Then looking into the above we also fixed the MAP_PRIVATE case.
Hugh by source review also found a data loss source if UFFDIO_COPY is
used on shmem MAP_SHARED PROT_READ mappings (the production usages
incidentally run with PROT_READ|PROT_WRITE, so the data loss couldn't
happen in those production usages like with QEMU).
The whole patchset is marked for stable.
We verified QEMU postcopy live migration with guest running on shmem
MAP_PRIVATE run as well as before after the fix of shmem MAP_PRIVATE.
Regardless if it's shmem or hugetlbfs or MAP_PRIVATE or MAP_SHARED, QEMU
unconditionally invokes a punch hole if the guest mapping is filebacked
and a MADV_DONTNEED too (needed to get rid of the MAP_PRIVATE COWs and
for the anon backend).
This patch (of 5):
We internally used EFAULT to communicate with the caller, switch to
ENOENT, so EFAULT can be used as a non internal retval.
Link: http://lkml.kernel.org/r/20181126173452.26955-2-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Jann Horn <jannh@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: <stable@vger.kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently on driver bringup with KASAN enabled, meson triggers an OOB
memory access as shown below:
[ 117.904528] ==================================================================
[ 117.904560] BUG: KASAN: global-out-of-bounds in meson_viu_set_osd_lut+0x7a0/0x890
[ 117.904588] Read of size 4 at addr ffff20000a63ce24 by task systemd-udevd/498
[ 117.904601]
[ 118.083372] CPU: 4 PID: 498 Comm: systemd-udevd Not tainted 4.20.0-rc3Lyude-Test+ #20
[ 118.091143] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 118.099768] Call trace:
[ 118.102181] dump_backtrace+0x0/0x3e8
[ 118.105796] show_stack+0x14/0x20
[ 118.109083] dump_stack+0x130/0x1c4
[ 118.112539] print_address_description+0x60/0x25c
[ 118.117214] kasan_report+0x1b4/0x368
[ 118.120851] __asan_report_load4_noabort+0x18/0x20
[ 118.125566] meson_viu_set_osd_lut+0x7a0/0x890
[ 118.129953] meson_viu_init+0x10c/0x290
[ 118.133741] meson_drv_bind_master+0x474/0x748
[ 118.138141] meson_drv_bind+0x10/0x18
[ 118.141760] try_to_bring_up_master+0x3d8/0x768
[ 118.146249] component_add+0x214/0x570
[ 118.149978] meson_dw_hdmi_probe+0x18/0x20 [meson_dw_hdmi]
[ 118.155404] platform_drv_probe+0x98/0x138
[ 118.159455] really_probe+0x2a0/0xa70
[ 118.163070] driver_probe_device+0x1b4/0x2d8
[ 118.167299] __driver_attach+0x200/0x280
[ 118.171189] bus_for_each_dev+0x10c/0x1a8
[ 118.175144] driver_attach+0x38/0x50
[ 118.178681] bus_add_driver+0x330/0x608
[ 118.182471] driver_register+0x140/0x388
[ 118.186361] __platform_driver_register+0xc8/0x108
[ 118.191117] meson_dw_hdmi_platform_driver_init+0x1c/0x1000 [meson_dw_hdmi]
[ 118.198022] do_one_initcall+0x12c/0x3bc
[ 118.201883] do_init_module+0x1fc/0x638
[ 118.205673] load_module+0x4b4c/0x6808
[ 118.209387] __se_sys_init_module+0x2e8/0x3c0
[ 118.213699] __arm64_sys_init_module+0x68/0x98
[ 118.218100] el0_svc_common+0x104/0x210
[ 118.221893] el0_svc_handler+0x48/0xb8
[ 118.225594] el0_svc+0x8/0xc
[ 118.228429]
[ 118.229887] The buggy address belongs to the variable:
[ 118.235007] eotf_33_linear_mapping+0x84/0xc0
[ 118.239301]
[ 118.240752] Memory state around the buggy address:
[ 118.245522] ffff20000a63cd00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 118.252695] ffff20000a63cd80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 118.259850] >ffff20000a63ce00: 00 00 00 00 04 fa fa fa fa fa fa fa 00 00 00 00
[ 118.267000] ^
[ 118.271222] ffff20000a63ce80: 00 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 118.278393] ffff20000a63cf00: 00 00 00 00 00 00 00 00 00 00 00 00 04 fa fa fa
[ 118.285542] ==================================================================
[ 118.292699] Disabling lock debugging due to kernel taint
It seems that when looping through the OSD EOTF LUT maps, we use the
same max iterator for OETF: 20. This is wrong though, since 20*2 is 40,
which means that we'll stop out of bounds on the EOTF maps.
But, this whole thing is already confusing enough to read through as-is,
so let's just replace all of the hardcoded sizes with
OSD_(OETF/EOTF)_LUT_SIZE / 2.
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller") Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: <stable@vger.kernel.org> # v4.10+ Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181125012117.31915-1-lyude@redhat.com Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seeing as we use this registermap in the context of our IRQ handlers, we
need to be using spinlocks for reading/writing registers so that we can
still read them from IRQ handlers without having to grab any mutexes and
accidentally sleep. We don't currently do this, as pointed out by
lockdep:
Since Linux 4.17, calls to drm_crtc_vblank_on/off are mandatory, and we get
a warning when ctrc is disabled :
" driver forgot to call drm_crtc_vblank_off()"
But, the vsync IRQ was not totally disabled due the transient hardware
state and specific interrupt line, thus adding proper IRQ masking from
the HHI system control registers.
The last change fixes a race condition introduced by calling the added
drm_crtc_vblank_on/off when an HPD event occurs from the HDMI connector,
triggering a WARN_ON() in the _atomic_begin() callback when the CRTC
is disabled, thus also triggering a WARN_ON() in drm_vblank_put() :
The issue is that vblank need to be enabled in any occurrence of :
- atomic_enable()
- atomic_begin() and state->enable == true, which was not the case
Moving the CRTC enable code to a common function and calling in one of
these occurrence solves this race condition and makes sure vblank is
enabled in each call to _atomic_begin() from the HPD event leading to
drm_atomic_helper_commit_planes().
To Summarize :
- Make sure that the CRTC code will call the drm_crtc_vblank_on()/off()
- *Really* mask the Vsync IRQ
- Initialize and enable vblank at the first
atomic_begin()/_atomic_enable()
Cc: stable@vger.kernel.org # 4.17+ Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed typos+added cc for stable] Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181122160103.10993-1-narmstrong@baylibre.com Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When drm_new_set_master() fails, set is_master to 0, to prevent a
possible NULL pointer deref.
Here is a problematic flow: we check is_master in drm_is_current_master(),
then proceed to call drm_lease_owner() passing master. If we do not restore
is_master status when drm_new_set_master() fails, we may have a situation
in which is_master will be 1 and master itself, NULL, leading to the deref
of a NULL pointer in drm_lease_owner().
This fixes the following OOPS, observed on an ArchLinux running a 4.19.2
kernel:
The change fixed huge delay in SST daisy chain and S3 soft hang
observed in 4.19 kernel rebase.
Regression point in drm:
drm/fb-helper: Eliminate the .best_encoder() usage
The aux sequence is altered due to the failure in
drm_connector_for_each_possible_encoder(). The failure is
caused by missing attached encoder in the process of adding
MST connector.
drm_dp_send_enum_path_resources() aux transaction is pushed after
mode probe, which causes conflict to drm_dp_mst_i2c_xfer(),
leading to the transaction timeout.
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com> Cc: Stable <stable@vger.kernel.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform has no IO space, ioregs is placed next to the already
allocated regs. In this case, it should not be separately freed.
This prevents a kernel warning from __vunmap "Trying to vfree()
nonexistent vm area" when unloading the driver.
Fixes: 0dd68309b9c5 ("drm/ast: Try to use MMIO registers when PIO isn't supported") Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tracefs file set_graph_function is used to only function graph functions
that are listed in that file (or all functions if the file is empty). The
way this is implemented is that the function graph tracer looks at every
function, and if the current depth is zero and the function matches
something in the file then it will trace that function. When other functions
are called, the depth will be greater than zero (because the original
function will be at depth zero), and all functions will be traced where the
depth is greater than zero.
The issue is that when a function is first entered, and the handler that
checks this logic is called, the depth is set to zero. If an interrupt comes
in and a function in the interrupt handler is traced, its depth will be
greater than zero and it will automatically be traced, even if the original
function was not. But because the logic only looks at depth it may trace
interrupts when it should not be.
The recent design change of the function graph tracer to fix other bugs
caused the depth to be zero while the function graph callback handler is
being called for a longer time, widening the race of this happening. This
bug was actually there for a longer time, but because the race window was so
small it seldom happened. The Fixes tag below is for the commit that widen
the race window, because that commit belongs to a series that will also help
fix the original bug.
Cc: stable@kernel.org Fixes: 39eb456dacb5 ("function_graph: Use new curr_ret_depth to manage depth instead of curr_ret_stack") Reported-by: Joe Lawrence <joe.lawrence@redhat.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the firmware reports a connection width that is not 1x, 4x, 8x or 12x
it causes the driver to fail during initialization.
To prevent this failure every time a new width is introduced to the RDMA
stack, we will set a default 4x width for these widths which ar unknown to
the driver.
This is needed to allow to run old kernels with new firmware.
Cc: <stable@vger.kernel.org> # 4.1 Fixes: 1b5daf11b015 ("IB/mlx5: Avoid using the MAD_IFC command under ISSI > 0 mode") Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Reviewed-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the nd_sd group is set to the sd-card function, Pins 45 + 46 are
configured as GPIOs. If they are blocked by the sd function, they can't
be used as GPIOs.
Reported-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: f576fb6a0700 ("MIPS: ralink: cleanup the soc specific pinmux data")
Patchwork: https://patchwork.linux-mips.org/patch/21220/ Cc: John Crispin <john@phrozen.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After enabling KVM event tracing, almost all of trace_kvm_exit()'s
printk shows
"kvm_exit: IRQ: ..."
even if the actual exception_type is NOT IRQ. More specifically,
trace_kvm_exit() is defined in virt/kvm/arm/trace.h by TRACE_EVENT.
This slight problem may have existed after commit e6753f23d961
("tracepoint: Make rcuidle tracepoint callers use SRCU"). There are
two variables in trace_kvm_exit() and __DO_TRACE() which have the
same name, *idx*. Thus the actual value of *idx* will be overwritten
when tracing. Fix it by adding a simple prefix.
Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Wang Haibin <wanghaibin.wang@huawei.com> Cc: linux-trace-devel@vger.kernel.org Cc: stable@vger.kernel.org Fixes: e6753f23d961 ("tracepoint: Make rcuidle tracepoint callers use SRCU") Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f5fe9fef5b2 ("sched/debug: Fix task state recording/printout")
tried to fix the problem introduced by a previous commit efb40f588b43
("sched/tracing: Fix trace_sched_switch task-state printing"). However
the prev_state output in sched_switch is still broken.
task_state_index() uses fls() which considers the LSB as 1. Left
shifting 1 by this value gives an incorrect mapping to the task state.
Fix this by decrementing the value returned by __get_task_state()
before shifting.
Since commit 4378a7d4be30 ("arm64: implement syscall wrappers")
introduced "__arm64_" prefix to all syscall wrapper symbols in
sys_call_table, syscall tracer can not find corresponding
metadata from syscall name. In the result, we have no syscall
ftrace events on arm64 kernel, and some bpf testcases are failed
on arm64.
To fix this issue, this introduces custom
arch_syscall_match_sym_name() which skips first 8 bytes when
comparing the syscall and symbol names.
Fix the size of the buffer allocated to store the in-memory BBT.
This bug was previously hidden by a different bug, that was fixed in
commit d098093ba06e ("mtd: nand: Fix nanddev_neraseblocks()").
Fixes: 9c3736a3de21 ("mtd: nand: Add core infrastructure to deal with NAND devices") Cc: <stable@vger.kernel.org> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
142b18ddc8143 ("uprobes: Fix handle_swbp() vs unregister() + register() race")
added the UPROBE_COPY_INSN flag, and corresponding smp_wmb() and smp_rmb()
memory barriers, to ensure that handle_swbp() uses fully-initialized
uprobes only.
However, the smp_rmb() is mis-placed: this barrier should be placed
after handle_swbp() has tested for the flag, thus guaranteeing that
(program-order) subsequent loads from the uprobe can see the initial
stores performed by prepare_uprobe().
Move the smp_rmb() accordingly. Also amend the comments associated
to the two memory barriers to indicate their actual locations.
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: stable@kernel.org Fixes: 142b18ddc8143 ("uprobes: Fix handle_swbp() vs unregister() + register() race") Link: http://lkml.kernel.org/r/20181122161031.15179-1-andrea.parri@amarulasolutions.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If for some reason we failed to query the mr status, we need to make sure
to provide sufficient information for an ambiguous error (guard error on
sector 0).
projects / users / dwmw2 / linux.git / log