Since the commit commit c6122688f265 ("drm/msm/mdp5: stop overriding
drvdata") reading the MDP5 hw revision on db410c will crash the board
as the MDSS_GDSC is not enabled. Revert a part of the offending commit
(moving rpm enablement) and set priv->kms earlier. This make it possible
to use pm_runtime_get_sync() during read_mdp_hw_revision(), which will
power up both the MDP5 and MDSS devices.
Commit 5441e9dafdfc6dc40 ("[media] s5p-mfc: Core support for MFC v7")
which adds mfc v7 support for Exynos3250 and use the same compatible
string as used by Exynos5240 but both the IPs are a bit different in
terms of IP clock.
Add variant driver data based on the new compatible string
"samsung,exynos3250-mfc" for Exynos3250 SoC.
Suggested-by: Alim Akhtar <alim.akhtar@samsung.com> Fixes: 5441e9dafdfc ("[media] s5p-mfc: Core support for MFC v7") Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver may can't get v4l2 buffer when lat or core decode timeout,
will lead to crash when call v4l2_m2m_buf_done to set dst buffer
(NULL pointer) done.
Fixes: 7b182b8d9c85 ("media: mediatek: vcodec: Refactor get and put capture buffer flow") Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
driver needs to cancel vpu before releasing the vpu instance,
so call v4l2_m2m_ctx_release() first,
to handle the redundant event triggered after m2m_ctx is released.
firmware should be waked up by start or configure command,
but there is a very small chance that firmware failed to wakeup.
in such case, try to wakeup firmware again by sending a noop command
This allows the device to probe and register its async subdev without
a sensor attached.
The rationale is that the parent driver might otherwise wait for the
subdev to be registered when it should be available (from the fwnode
graph endpoint perspective). This is generally not problematic when
the MIPI CSI-2 bridge is the only device attached to the parent, but
in the case of a CSI controller that can feed from both MIPI CSI-2
and parallel, it would prevent using the parallel sensor due to the
parent waiting for the MIPI CSI-2 subdev to register.
Fixes: 576d196c522b ("media: sunxi: Add support for the A83T MIPI CSI-2 controller") Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This allows the device to probe and register its async subdev without
a sensor attached.
The rationale is that the parent driver might otherwise wait for the
subdev to be registered when it should be available (from the fwnode
graph endpoint perspective). This is generally not problematic when
the MIPI CSI-2 bridge is the only device attached to the parent, but
in the case of a CSI controller that can feed from both MIPI CSI-2
and parallel, it would prevent using the parallel sensor due to the
parent waiting for the MIPI CSI-2 subdev to register.
Fixes: af54b4f4c17f ("media: sunxi: Add support for the A31 MIPI CSI-2 controller") Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running as a Xen PV guest there is no need for setting up the
realmode trampoline, as realmode isn't supported in this environment.
Trying to setup the trampoline has been proven to be problematic in
some cases, especially when trying to debug early boot problems with
Xen requiring to keep the EFI boot-services memory mapped (some
firmware variants seem to claim basically all memory below 1Mb for boot
services).
Introduce new x86_platform_ops operations for that purpose, which can
be set to a NOP by the Xen PV specific kernel boot code.
[ bp: s/call_init_real_mode/do_init_real_mode/ ]
Fixes: 084ee1c641a0 ("x86, realmode: Relocator for realmode code") Suggested-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/r/20221123114523.3467-1-jgross@suse.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In dvb_register_frontend(), dvb_register_device() is possible to fail
but its return value is ignored.
It will cause use-after-free when module is removed, because in
dvb_unregister_frontend() it tries to unregister a not registered
device.
BUG: KASAN: use-after-free in dvb_remove_device+0x18b/0x1f0 [dvb_core]
Read of size 4 at addr ffff88800dff4824 by task rmmod/428
CPU: 3 PID: 428 Comm: rmmod
Call Trace:
<TASK>
...
dvb_remove_device+0x18b/0x1f0 [dvb_core]
dvb_unregister_frontend+0x7b/0x130 [dvb_core]
vidtv_bridge_remove+0x6e/0x160 [dvb_vidtv_bridge]
...
Fix this by catching return value of dvb_register_device().
However the fe->refcount can't be put to zero immediately, because
there are still modules calling dvb_frontend_detach() when
dvb_register_frontend() fails.
while the imx8mn_enet_phy_sels list didn't contained audio_pll1_out for
source select bits 101b.
Fixes: 96d6392b54dbb ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-6-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
while the imx8mn_sai2_sels list contained clk_ext3 and clk_ext4 for
source select bits 110b and 111b.
Fixes: 96d6392b54dbb ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-5-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike audio_pll1 and audio_pll2, there is no video_pll2. Further, the
name used in the RM is video_pll. So, let's rename "video_pll1" to
"video_pll" to be consistent with the RM and avoid misunderstandings.
The IMX8MN_VIDEO_PLL1* constants have not been removed to ensure
backward compatibility of the patch.
No functional changes intended.
Fixes: 96d6392b54dbb ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-4-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no occurrence of the hdmi oscillator in the reference manual
(document IMX8MNRM Rev 2, 07/2022). Further, if we consider the indexes
76-81 and 134 of the "Clock Root" table of chapter 5 of the RM, there is
no entry for the source select bits 101b, which is the setting referenced
by "osc_hdmi".
Fix by renaming "osc_hdmi" with "dummy", a clock which has already been
used for missing source select bits.
Tested on the BSH SystemMaster (SMM) S2 board.
Fixes: 96d6392b54dbb ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-3-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The IMX8MN platform does not have any video processing unit (VPU), and
indeed in the reference manual (document IMX8MNRM Rev 2, 07/2022) there
is no occurrence of its pll. From an analysis of the code and the RM
itself, I think vpu pll is used instead of m7 alternate pll, probably
for copy and paste of code taken from modules of similar architectures.
As an example for all, if we consider the second row of the "Clock Root"
table of chapter 5 (Clocks and Power Management) of the RM:
but in the source code, the imx8mn_m7_sels clocks list contains vpu_pll
for the source select bits 011b.
So, let's rename "vpu_pll" to "m7_alt_pll" to be consistent with the RM.
The IMX8MN_VPU_* constants have not been removed to ensure backward
compatibility of the patch.
No functional changes intended.
Fixes: 96d6392b54dbb ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-2-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The mt9p031_init_cfg() already calls __mt9p031_get_pad_crop(), which
correctly calls v4l2_subdev_get_try_crop() on V4L2_SUBDEV_FORMAT_TRY
or returns &mt9p031->crop on V4L2_SUBDEV_FORMAT_ACTIVE. No need to
call v4l2_subdev_get_try_crop() in mt9p031_init_cfg() again in case
of both V4L2_SUBDEV_FORMAT_TRY and V4L2_SUBDEV_FORMAT_ACTIVE.
This also fixes a splat generated by this call since commit 2ba3e38517f5a ("media: v4l: subdev: Fail graciously when getting try data for NULL state")
because v4l2_subdev_get_try_crop() is called with sd_state = NULL
in mt9p031_init_cfg().
Fixes: 69681cd041648 ("media: mt9p031: Move open subdev op init code into init_cfg") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 9babbbaaeb87 ("media: imx: imx7-media-csi: Use dual sampling for
YUV 1X16") set BIT_MIPI_DOUBLE_CMPNT in the CR18 register for 16-bit YUV
formats in imx7_csi_configure(). The CR18 register is always updated
with read-modify-write cycles, so if a 16-bit YUV format is selected,
the bit will stay set forever, even if the format is changed. Fix it by
clearing the bit at the beginning of the imx7_csi_configure() function.
While at it, swap two of the bits being cleared to match the MSB to LSB
order. This doesn't cause any functional change.
Fixes: 9babbbaaeb87 ("media: imx: imx7-media-csi: Use dual sampling for YUV 1X16") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Paul Elder <paul.elder@ideasonboard.com> Acked-by: Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function send_packet() has a race condition as follows:
func send_packet()
{
// do work
call usb_submit_urb()
mutex_unlock()
wait_for_event_interruptible() <-- lock gone
mutex_lock()
}
func vfd_write()
{
mutex_lock()
call send_packet() <- prev call is not completed
mutex_unlock()
}
When the mutex is unlocked and the function send_packet() waits for the
call to complete, vfd_write() can start another call, which leads to the
"URB submitted while active" warning in usb_submit_urb().
Fix this by removing the mutex_unlock() call in send_packet() and using
mutex_lock_interruptible().
In vimc_init(), when platform_driver_register(&vimc_pdrv) fails,
platform_driver_unregister(&vimc_pdrv) is wrongly called rather than
platform_device_unregister(&vimc_pdev), which causes kernel warning:
SND_SOC_QCOM_COMMON depends on SOUNDWIRE for some symbols but this
is not explicitly specified using Kconfig depends. On the other hand
SND_SOC_QCOM_COMMON is also directly selected by the sound card
Kconfigs, this could result in various combinations and some symbols
ending up in modules and soundcard that uses those symbols as in-build
driver.
Fix these issues by explicitly specifying the dependencies of
SND_SOC_QCOM_COMMON and also use imply a to select SND_SOC_QCOM_COMMON
so that the symbol is selected based on its dependencies.
Also remove dummy stubs in common.c around CONFIG_SOUNDWIRE
Fixes: 3bd975f3ae0a ("ASoC: qcom: sm8250: move some code to common") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20221124140351.407506-1-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A submitter workqueue is dynamically allocated by init_submitter()
called by drbd_create_device(), we should destroy it when this
device is not needed or destroyed.
Fixes: 113fef9e20e0 ("drbd: prepare to queue write requests on a submit worker") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Link: https://lore.kernel.org/r/20221124015817.2729789-3-bobo.shaobowang@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
This revert c2258ffc56f2 ("drbd: poison free'd device, resource and
connection structs"), add memset is odd here for debugging, there are
some methods to accurately show what happened, such as kdump.
del_mtd_device() will call of_node_put() to mtd_get_of_node(mtd), which
is mtd->dev.of_node. However, memset(&mtd->dev, 0) is called before
of_node_put(). As the result, of_node_put() won't do anything in
del_mtd_device(), and causes the refcount leak.
Before this change when a bond in mode 2 lost link, all of its slaves
lost link, the bonding device would never recover even after the
expiration of updelay. This change removes the updelay when the bond
currently has no usable links. Conforming to bonding.txt section 13.1
paragraph 4.
Fixes: 41f891004063 ("bonding: ignore updelay param when there is no active slave") Signed-off-by: Jonathan Toppins <jtoppins@redhat.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiri reports broken test_progs after recent commit 68f8e3d4b916
("selftests/bpf: Make sure zero-len skbs aren't redirectable").
Apparently we don't remount debugfs when we switch back networking namespace.
Let's explicitly mount /sys/kernel/debug.
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak.
Fixes: 3f12acc8d6d4 ("drm/amdgpu: put the audio codec into suspend state before gpu reset V3") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If clk_register() fails, @pll->rate_table may have allocated memory by
kmemdup(), so it needs to be freed, otherwise will cause memory leak
issue, this patch fixes it.
Fixes: 90c590254051 ("clk: rockchip: add clock type for pll clocks and pll used on rk3066") Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Link: https://lore.kernel.org/r/20221123091201.199819-1-xiujianfeng@huawei.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use kfree_const() to free supply_name conditionally in create_regulator()
as supply_name may be allocated from kmalloc() or directly from .rodata
section.
Fixes: 87fe29b61f95 ("regulator: push allocations in create_regulator() outside of lock") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Link: https://lore.kernel.org/r/20221123034616.3609537-1-bobo.shaobowang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in sound/core/seq/seq_clientmgr.c:509:22
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x44
__ubsan_handle_shift_out_of_bounds+0x1e7/0x208
snd_seq_deliver_single_event.constprop.21+0x191/0x2f0
snd_seq_deliver_event+0x1a2/0x350
snd_seq_kernel_client_dispatch+0x8b/0xb0
snd_seq_client_notify_subscription+0x72/0xa0
snd_seq_ioctl_subscribe_port+0x128/0x160
snd_seq_kernel_client_ctl+0xce/0xf0
snd_seq_oss_create_client+0x109/0x15b
alsa_seq_oss_init+0x11c/0x1aa
do_one_initcall+0x80/0x440
kernel_init_freeable+0x370/0x3c3
kernel_init+0x1b/0x190
ret_from_fork+0x1f/0x30
</TASK>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in sound/core/pcm_native.c:2676:21
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x44
__ubsan_handle_shift_out_of_bounds+0x1e7/0x208
snd_pcm_open_substream+0x9f0/0xa90
snd_pcm_oss_open.part.26+0x313/0x670
snd_pcm_oss_open+0x30/0x40
soundcore_open+0x18b/0x2e0
chrdev_open+0xe2/0x270
do_dentry_open+0x2f7/0x620
path_openat+0xd66/0xe70
do_filp_open+0xe3/0x170
do_sys_openat2+0x357/0x4a0
do_sys_open+0x87/0xd0
do_syscall_64+0x34/0x80
Since for_each_available_child_of_node() will increase the refcount of
node, we need to call of_node_put() manually when breaking out of the
iteration.
This is no bugfix (so no Fixes: tag is necessary) as it is
taken care of in hid_sensor_custom_add_attributes().
The motivation for this patch is that:
hid_sensor_custom_field.attr_name and
hid_sensor_custom_field.attrs
has the size of HID_CUSTOM_TOTAL_ATTRS and used in same context.
We compare against HID_CUSTOM_TOTAL_ATTRS when
looping through hid_custom_attrs.
We will silent the smatch error:
hid_sensor_custom_add_attributes() error: buffer overflow
'hid_custom_attrs' 8 <= 10
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per update Reference Mannual, correct the enet clock parent to
wakeup_axi_root.
Fixes: 24defbe194b6 ("clk: imx: add i.MX93 clk") Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221028095211.2598312-3-peng.fan@oss.nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The anatop base is not unmapped during error handling path, fix it.
Fixes: 24defbe194b6 ("clk: imx: add i.MX93 clk") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221028095211.2598312-2-peng.fan@oss.nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
HID-RMI is special in the sense that it does not carry HID events
directly, but rather uses HID protocol as a wrapper/transport for RMI
protocol. Therefore we should not assume that all data coming from the
device via interrupt is associated with user activity and report wakeup
event indiscriminately, but rather let HID-RMI do that when appropriate.
HID-RMI devices tag responses to the commands issued by the host as
RMI_READ_DATA_REPORT_ID whereas motion and other input events from the
device are tagged as RMI_ATTN_REPORT_ID. Change hid-rmi to report wakeup
events when receiving the latter packets. This allows ChromeOS to
accurately identify wakeup source and make correct decision on the mode
of the resume the system should take ("dark" where the display stays off
vs normal one).
bpf_iter_attach_cgroup() has already acquired an extra reference for the
start cgroup, but the reference may be released if the iterator link fd
is closed after the creation of iterator fd, and it may lead to
user-after-free problem when reading the iterator fd.
An alternative fix is pinning iterator link when opening iterator,
but it will make iterator link being still visible after the close of
iterator link fd and the behavior is different with other link types, so
just fixing it by acquiring another reference for the start cgroup.
Fixes: d4ccaf58a847 ("bpf: Introduce cgroup iter") Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20221121073440.1828292-2-houtao@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The number of bytes used by spi_nor_spimem_check_readop() may be
incorrect for the dummy cycles. Since nor->read_dummy is not initialized
before spi_nor_spimem_adjust_hwcaps().
We use both mode and wait state clock cycles instead of nor->read_dummy.
We assume the correct errno is -EADDRINUSE when sk->sk_prot->get_port()
fails, so some ->get_port() functions return just 1 on failure and the
callers return -EADDRINUSE instead.
However, mptcp_get_port() can return -EINVAL. Let's not ignore the error.
Note the only exception is inet_autobind(), all of whose callers return
-EAGAIN instead.
Fixes: cec37a6e41aa ("mptcp: Handle MP_CAPABLE options for outgoing connections") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds no functional change and cleans up some functions
that the following patches touch around so that we make them tidy
and easy to review/revert. The change is mainly to keep reverse
christmas tree order.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7a7160edf1bf ("net: Return errno in sk->sk_prot->get_port().") Signed-off-by: Sasha Levin <sashal@kernel.org>
dma_alloc_coherent does not return a physical address, but a DMA address,
which might be remapped or have an offset. Passing the DMA address to
vm_iomap_memory is thus broken.
Use the proper dma_mmap_coherent helper instead, and stop passing
__GFP_COMP to dma_alloc_coherent, as the memory management inside the
DMA allocator is hidden from the callers and does not require it.
With this the gfp_t argument to __videobuf_dc_alloc can be removed and
hard coded to GFP_KERNEL.
A problem about modprobe amphion-vpu failed is triggered with the
following log given:
[ 2208.634841] Error: Driver 'amphion-vpu' is already registered, aborting...
modprobe: ERROR: could not insert 'amphion_vpu': Device or resource busy
The reason is that vpu_driver_init() returns vpu_core_driver_init()
directly without checking its return value, if vpu_core_driver_init()
failed, it returns without unregister amphion_vpu_driver, resulting the
amphion-vpu can never be installed later.
A simple call graph is shown as below:
vpu_driver_init()
platform_driver_register() # register amphion_vpu_driver
vpu_core_driver_init()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister amphion_vpu_driver
Fix by unregister amphion_vpu_driver when vpu_core_driver_init() returns
error.
A problem about modprobe s5p_fimc failed is triggered with the
following log given:
[ 272.075275] Error: Driver 'exynos4-fimc' is already registered, aborting...
modprobe: ERROR: could not insert 's5p_fimc': Device or resource busy
The reason is that fimc_md_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without unregister fimc_driver, resulting the
s5p_fimc can never be installed later.
A simple call graph is shown as below:
fimc_md_init()
fimc_register_driver() # register fimc_driver
platform_driver_register()
platform_driver_register()
driver_register()
bus_add_driver()
dev = kzalloc(...) # OOM happened
# return without unregister fimc_driver
Fix by unregister fimc_driver when platform_driver_register() returns
error.
Fixes: d3953223b090 ("[media] s5p-fimc: Add the media device driver") Signed-off-by: Yuan Can <yuancan@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() returns error in solo_sysfs_init(), the
name allocated by dev_set_name() need be freed. As comment of
device_register() says, it should use put_device() to give up
the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup().
Fixes: dcae5dacbce5 ("[media] solo6x10: sync to latest code from Bluecherry's git repo") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is because the error handling in vidtv_bridge_dvb_init() is wrong.
First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but
goto fail_dmx(_dev): calls release functions again, which causes
use-after-free.
Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause
out-of-bound when i finished its loop (i == NUM_FE). And the loop
releasing is wrong, although now NUM_FE is 1 so it won't cause problem.
Fix this by correctly releasing everything.
Fixes: f90cf6079bf6 ("media: vidtv: add a bridge driver") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
the capture format may be changed when
sequence header is parsed,
it may be read and write in the same time,
add lock around vdec_g_fmt to synchronize it
Restore user configured MTU running mtk_hw_init() during tx timeout routine
since it will be overwritten after a hw reset.
Reported-by: Felix Fietkau <nbd@nbd.name> Fixes: 9ea4d311509f ("net: ethernet: mediatek: add the whole ethernet reset into the reset process") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
sound/soc/amd/acp/acp-platform.c:199 acp_dma_open() warn:
'&stream->list' not removed from list
If snd_pcm_hw_constraint_integer() fails in acp_dma_open(),
stream will be freed, but stream->list will not be removed from
adata->stream_list, then list traversal may cause UAF.
Fix by adding the newly allocated stream to the list once it's fully
initialised.
Fixes: 7929985cfe36 ("ASoC: amd: acp: Initialize list to store acp_stream during pcm_open") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221118030056.3135960-1-cuigaosheng1@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
If we get an error (other than -ENOENT) we need to propagate that up the
stack. Otherwise if the nvmem driver hasn't probed yet, we'll end up
end up claiming that we support all the OPPs which is not likely to be
true (and on some generations impossible to be true, ie. if there are
conflicting OPPs).
Fixes: fe7952c629da ("drm/msm: Add speed-bin support to a618 gpu") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/511690/ Link: https://lore.kernel.org/r/20221115154637.1613968-1-robdclark@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver is attempting to register to support two different buses.
if either of these is successful then ath10k_pci_init() should return 0
so that hardware attached to the successful bus can be probed and
supported. only if both of these are unsuccessful should ath10k_pci_init()
return an errno.
Fixes: 0b523ced9a3c ("ath10k: add basic skeleton to support ahb") Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221110061926.18163-1-xiujianfeng@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The core problem is that the LSM is not yet fully stacked (work is
actively going on in this space) which means that some LSM hooks do
not support multiple LSMs at the same time. To fix, skip the
"EPERM" test when it runs in the environments that already have
non-bpf lsms installed
Fixes: dca85aac8895 ("selftests/bpf: lsm_cgroup functional test") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Cc: Stanislav Fomichev <sdf@google.com> Acked-by: Stanislav Fomichev <sdf@google.com> Link: https://lore.kernel.org/r/1668482980-16163-1-git-send-email-wangyufen@huawei.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dm is a bit special in that it opens the underlying devices. Commit 89f871af1b26 ("dm: delay registering the gendisk") tried to accommodate
that by allowing to add the holder to the list before add_gendisk and
then just add them to sysfs once add_disk is called. But that leads to
really odd lifetime problems and error handling problems as we can't
know the state of the kobjects and don't unwind properly. To fix this
switch to just registering all existing table_devices with the holder
code right after add_disk, and remove them before calling del_gendisk.
Take the list unlink and free into close_table_device so that no half
torn down table_devices exist. Also remove the check for a NULL bdev
as that can't happen - open_table_device never adds a table_device to
the list that does not have a valid block_device.
Move all the logic for allocation the table_device and linking it into
the list into the open_table_device. This keeps the code tidy and
ensures that the table_devices only exist in fully initialized state.
Zero out the pointer to ->slave_dir so that the holder code doesn't
incorrectly treat the object as alive when add_disk failed or after
del_gendisk was called.
The input parameter @fields is type of struct ima_template_field ***, so
when allocates array memory for @fields, the size of element should be
sizeof(**field) instead of sizeof(*field).
Actually the original code would not cause any runtime error, but it's
better to make it logically right.
Currently the fallback SG allocation tries to allocate each single
page, and this tends to result in the reverse order of memory
addresses when large space is available at boot, as the kernel takes a
free page from the top to the bottom in the zone. The end result
looks as if non-contiguous (although it actually is). What's worse is
that it leads to an overflow of BDL entries for HD-audio.
For avoiding such a problem, this patch modifies the allocation code
slightly; now it tries to allocate the larger contiguous chunks as
much as possible, then reduces to the smaller chunks only if the
allocation failed -- a similar strategy as the existing
snd_dma_alloc_pages_fallback() function.
Along with the trick, drop the unused address array from
snd_dma_sg_fallback object. It was needed in the past when
dma_alloc_coherent() was used, but with the standard page allocator,
it became superfluous and never referred.
In the PP_OD_EDIT_VDDC_CURVE case the "input_index" variable is capped at
2 but not checked for negative values so it results in an out of bounds
read. This value comes from the user via sysfs.
Fixes: d5bf26539494 ("drm/amd/powerplay: added vega20 overdrive support V3") Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called.
Fixes: 69511a452e6d ("regulator: map consumer regulator based on device tree") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221115091508.900752-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
xdp_synproxy fails to be compiled in the 32-bit arch, log is as follows:
xdp_synproxy.c: In function 'parse_options':
xdp_synproxy.c:175:36: error: left shift count >= width of type [-Werror=shift-count-overflow]
175 | *tcpipopts = (mss6 << 32) | (ttl << 24) | (wscale << 16) | mss4;
| ^~
xdp_synproxy.c: In function 'syncookie_open_bpf_maps':
xdp_synproxy.c:289:28: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
289 | .map_ids = (__u64)map_ids,
| ^
Fix it.
Fixes: fb5cd0ce70d4 ("selftests/bpf: Add selftests for raw syncookie helpers") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20221111030836.37632-1-yangjihong1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
../sound/soc/codecs/wsa883x.c: In function 'wsa883x_probe':
../sound/soc/codecs/wsa883x.c:1394:25: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_regulator_get_optional'? [-Werror=implicit-function-declaration]
wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown",
../sound/soc/codecs/wsa883x.c:1395:49: error: 'GPIOD_FLAGS_BIT_NONEXCLUSIVE' undeclared (first use in this function)
GPIOD_FLAGS_BIT_NONEXCLUSIVE);
../sound/soc/codecs/wsa883x.c:1414:9: error: implicit declaration of function 'gpiod_direction_output'; did you mean 'gpio_direction_output'? [-Werror=implicit-function-declaration]
gpiod_direction_output(wsa883x->sd_n, 1);
Fixes: 43b8c7dc85a1 ("ASoC: codecs: add wsa883x amplifier support") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Banajit Goswami <bgoswami@quicinc.com> Cc: Mark Brown <broonie@kernel.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: alsa-devel@alsa-project.org Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20221108001829.5100-1-rdunlap@infradead.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The shutdown GPIO is active low (SD_N), but this depends on actual board
layout. Linux drivers should only care about logical state, where high
(1) means shutdown and low (0) means do not shutdown.
Invert the GPIO to match logical value.
Fixes: 43b8c7dc85a1 ("ASoC: codecs: add wsa883x amplifier support") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20221110133512.478831-2-krzysztof.kozlowski@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / jedix / linux-maple.git / log