mm_pkey_is_allocated() treats pkey 0 as unallocated. That is
inconsistent with the manpages, and also inconsistent with
mm->context.pkey_allocation_map. Stop special casing it and only
disallow values that are actually bad (< 0).
The end-user visible effect of this is that you can now use
mprotect_pkey() to set pkey=0.
This is a bit nicer than what Ram proposed[1] because it is simpler
and removes special-casing for pkey 0. On the other hand, it does
allow applications to pkey_free() pkey-0, but that's just a silly
thing to do, so we are not going to protect against it.
The scenario that could happen is similar to what happens if you free
any other pkey that is in use: it might get reallocated later and used
to protect some other data. The most likely scenario is that pkey-0
comes back from pkey_alloc(), an access-disable or write-disable bit
is set in PKRU for it, and the next stack access will SIGSEGV. It's
not horribly different from if you mprotect()'d your stack or heap to
be unreadable or unwritable, which is generally very foolish, but also
not explicitly prevented by the kernel.
The problem is hit when the mprotect(PROT_EXEC)
is implicitly assigned a protection key to the VMA, and made
that key ACCESS_DENY|WRITE_DENY. The PROT_NONE mprotect()
failed to remove the protection key, and the PROT_NONE->
PROT_READ left the PTE usable, but the pkey still in place
and left the memory inaccessible.
To fix this, we ensure that we always "override" the pkee
at mprotect() if the VMA does not have execute-only
permissions, but the VMA has the execute-only pkey.
We had a check for PROT_READ/WRITE, but it did not work
for PROT_NONE. This entirely removes the PROT_* checks,
which ensures that PROT_NONE now works.
Reported-by: Shakeel Butt <shakeelb@google.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellermen <mpe@ellerman.id.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Cc: stable@vger.kernel.org Fixes: 62b5f7d013f ("mm/core, x86/mm/pkeys: Add execute-only protection keys support") Link: http://lkml.kernel.org/r/20180509171351.084C5A71@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct a trinity finding for the perf_event_open() system call with
a perf event attribute structure that uses a frequency but has the
sampling frequency set to zero. This causes a FP divide exception during
the sample rate initialization for the hardware sampling facility.
Fixes: 8c069ff4bd606 ("s390/perf: add support for the CPU-Measurement Sampling Facility") Cc: stable@vger.kernel.org # 3.14+ Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since CQ/QAOB support was added, calling qdio_free() straight after
qdio_alloc() results in qdio_release_memory() accessing uninitialized
memory (ie. q->u.out.use_cq and q->u.out.aobs). Followed by a
kmem_cache_free() on the random AOB addresses.
For older kernels that don't have 6e30c549f6ca, the same applies if
qdio_establish() fails in the DEV_STATE_ONLINE check.
While initializing q->u.out.use_cq would be enough to fix this
particular bug, the more future-proof change is to just zero-alloc the
whole struct.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks") Cc: <stable@vger.kernel.org> #v3.2+ Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is unsafe to do virtual to physical translations before mm_init() is
called if struct page is needed in order to determine the memory section
number (see SECTION_IN_PAGE_FLAGS). This is because only in mm_init()
we initialize struct pages for all the allocated memory when deferred
struct pages are used.
My recent fix in commit c9e97a1997 ("mm: initialize pages on demand
during boot") exposed this problem, because it greatly reduced number of
pages that are initialized before mm_init(), but the problem existed
even before my fix, as Fengguang Wu found.
Below is a more detailed explanation of the problem.
We initialize struct pages in four places:
1. Early in boot a small set of struct pages is initialized to fill the
first section, and lower zones.
2. During mm_init() we initialize "struct pages" for all the memory that
is allocated, i.e reserved in memblock.
3. Using on-demand logic when pages are allocated after mm_init call
(when memblock is finished)
4. After smp_init() when the rest free deferred pages are initialized.
The problem occurs if we try to do va to phys translation of a memory
between steps 1 and 2. Because we have not yet initialized struct pages
for all the reserved pages, it is inherently unsafe to do va to phys if
the translation itself requires access of "struct page" as in case of
this combination: CONFIG_SPARSE && !CONFIG_SPARSE_VMEMMAP
We disable this path by not allowing NEED_PER_CPU_KM with deferred
struct pages feature.
The problems are discussed in these threads:
http://lkml.kernel.org/r/20180418135300.inazvpxjxowogyge@wfg-t540p.sh.intel.com
http://lkml.kernel.org/r/20180419013128.iurzouiqxvcnpbvz@wfg-t540p.sh.intel.com
http://lkml.kernel.org/r/20180426202619.2768-1-pasha.tatashin@oracle.com
Link: http://lkml.kernel.org/r/20180515175124.1770-1-pasha.tatashin@oracle.com Fixes: 3a80a7fa7989 ("mm: meminit: initialise a subset of struct pages if CONFIG_DEFERRED_STRUCT_PAGE_INIT is set") Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Steven Sistare <steven.sistare@oracle.com> Cc: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Dennis Zhou <dennisszhou@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a race in the multi-order iteration code which causes the kernel to
hit a GP fault. This was first seen with a production v4.15 based
kernel (4.15.6-300.fc27.x86_64) utilizing a DAX workload which used
order 9 PMD DAX entries.
The race has to do with how we tear down multi-order sibling entries
when we are removing an item from the tree. Remember for example that
an order 2 entry looks like this:
where 'entry' is in some slot in the struct radix_tree_node, and the
three slots following 'entry' contain sibling pointers which point back
to 'entry.'
replace_slot() first removes the siblings in order from the first to the
last, then at then replaces 'entry' with NULL. This means that for a
brief period of time we end up with one or more of the siblings removed,
so:
This causes an issue if you have a reader iterating over the slots in
the tree via radix_tree_for_each_slot() while only under
rcu_read_lock()/rcu_read_unlock() protection. This is a common case in
mm/filemap.c.
The issue is that when __radix_tree_next_slot() => skip_siblings() tries
to skip over the sibling entries in the slots, it currently does so with
an exact match on the slot directly preceding our current slot.
Normally this works:
V preceding slot
struct radix_tree_node.slots[] = [entry][sibling][sibling][sibling]
^ current slot
This lets you find the first sibling, and you skip them all in order.
But in the case where one of the siblings is NULL, that slot is skipped
and then our sibling detection is interrupted:
V preceding slot
struct radix_tree_node.slots[] = [entry][NULL][sibling][sibling]
^ current slot
This means that the sibling pointers aren't recognized since they point
all the way back to 'entry', so we think that they are normal internal
radix tree pointers. This causes us to think we need to walk down to a
struct radix_tree_node starting at the address of 'entry'.
In a real running kernel this will crash the thread with a GP fault when
you try and dereference the slots in your broken node starting at
'entry'.
We fix this race by fixing the way that skip_siblings() detects sibling
nodes. Instead of testing against the preceding slot we instead look
for siblings via is_sibling_entry() which compares against the position
of the struct radix_tree_node.slots[] array. This ensures that sibling
entries are properly identified, even if they are no longer contiguous
with the 'entry' they point to.
Link: http://lkml.kernel.org/r/20180503192430.7582-6-ross.zwisler@linux.intel.com Fixes: 148deab223b2 ("radix-tree: improve multiorder iterators") Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reported-by: CR, Sapthagirish <sapthagirish.cr@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Matthew Wilcox <willy@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Chinner <david@fromorbit.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I had neglected to increment the error counter when the tests failed,
which made the tests noisy when they fail, but not actually return an
error code.
Link: http://lkml.kernel.org/r/20180509114328.9887-1-mpe@ellerman.id.au Fixes: 3cc78125a081 ("lib/test_bitmap.c: add optimisation tests") Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reported-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Yury Norov <ynorov@caviumnetworks.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: <stable@vger.kernel.org> [4.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch matches the sysfs name used in the unlinking with the
linking function. Otherwise, remove_compat_control_link() fails to remove
sysfs created by create_compat_control_link() in drm_dev_register().
Fixes: 6449b088dd51 ("drm: Add fake controlD* symlinks for backwards
compat") Cc: Dave Airlie <airlied@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
[seanpaul added Fixes and Cc tags] Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180511041542.GA4253@haneen-vb Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly to opal_event_shutdown, opal_nvram_write can be called in
the crash path with irqs disabled. Special case the delay to avoid
sleeping in invalid context.
Not all revisions of DW I2C controller implement the enable status register.
On platforms where that's the case (e.g. BG2CD and SPEAr ARM SoCs), waiting
for enable will time out as reading the unimplemented register yields zero.
It was observed that reading the IC_ENABLE_STATUS register once suffices to
avoid getting it stuck on Bay Trail hardware, so replace polling with one
dummy read of the register.
Fixes: fba4adbbf670 ("i2c: designware: must wait for enable") Signed-off-by: Alexander Monakov <amonakov@ispras.ru> Tested-by: Ben Gardner <gardner.ben@gmail.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_header_pointer will copy data into a buffer if data is non linear,
otherwise it will return a pointer in the linear section of the data.
nf_sk_lookup_slow_v{4,6} always copies data of size udphdr but later
accesses memory within the size of tcphdr (th->doff) in case of TCP
packets. This causes a crash when running with KASAN with the following
call stack -
BUG: KASAN: stack-out-of-bounds in xt_socket_lookup_slow_v4+0x524/0x718
net/netfilter/xt_socket.c:178
Read of size 2 at addr ffffffe3d417a87c by task syz-executor/28971
CPU: 2 PID: 28971 Comm: syz-executor Tainted: G B W O 4.9.65+ #1
Call trace:
[<ffffff9467e8d390>] dump_backtrace+0x0/0x428 arch/arm64/kernel/traps.c:76
[<ffffff9467e8d7e0>] show_stack+0x28/0x38 arch/arm64/kernel/traps.c:226
[<ffffff946842d9b8>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffff946842d9b8>] dump_stack+0xd4/0x124 lib/dump_stack.c:51
[<ffffff946811d4b0>] print_address_description+0x68/0x258 mm/kasan/report.c:248
[<ffffff946811d8c8>] kasan_report_error mm/kasan/report.c:347 [inline]
[<ffffff946811d8c8>] kasan_report.part.2+0x228/0x2f0 mm/kasan/report.c:371
[<ffffff946811df44>] kasan_report+0x5c/0x70 mm/kasan/report.c:372
[<ffffff946811bebc>] check_memory_region_inline mm/kasan/kasan.c:308 [inline]
[<ffffff946811bebc>] __asan_load2+0x84/0x98 mm/kasan/kasan.c:739
[<ffffff94694d6f04>] __tcp_hdrlen include/linux/tcp.h:35 [inline]
[<ffffff94694d6f04>] xt_socket_lookup_slow_v4+0x524/0x718 net/netfilter/xt_socket.c:178
Fix this by copying data into appropriate size headers based on protocol.
Fixes: a583636a83ea ("inet: refactor inet[6]_lookup functions to take skb") Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rules in nftables a free'd using kfree, but protected by rcu, i.e. we
must wait for a grace period to elapse.
Normal removal patch does this, but nf_tables_newrule() doesn't obey
this rule during error handling.
It calls nft_trans_rule_add() *after* linking rule, and, if that
fails to allocate memory, it unlinks the rule and then kfree() it --
this is unsafe.
Switch order -- first add rule to transaction list, THEN link it
to public list.
Note: nft_trans_rule_add() uses GFP_KERNEL; it will not fail so this
is not a problem in practice (spotted only during code review).
Fixes: 0628b123c96d12 ("netfilter: nfnetlink: add batch support and use it from nf_tables") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set->name must be free'd here in case ops->init fails.
Fixes: 387454901bd6 ("netfilter: nf_tables: Allow set names of up to 255 chars") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bump the file's refcount before moving the reference into the fd table,
not afterwards. The old code could drop the file's refcount to zero for a
short moment before calling get_file() via get_dma_buf().
This code can only be triggered on ARM systems that use Linaro's OP-TEE.
Doing an audit of trace events, I discovered two trace events in the xen
subsystem that use a hack to create zero data size trace events. This is not
what trace events are for. Trace events add memory footprint overhead, and
if all you need to do is see if a function is hit or not, simply make that
function noinline and use function tracer filtering.
Worse yet, the hack used was:
__array(char, x, 0)
Which creates a static string of zero in length. There's assumptions about
such constructs in ftrace that this is a dynamic string that is nul
terminated. This is not the case with these tracepoints and can cause
problems in various parts of ftrace.
Nuke the trace events!
Link: http://lkml.kernel.org/r/20180509144605.5a220327@gandalf.local.home Cc: stable@vger.kernel.org Fixes: 95a7d76897c1e ("xen/mmu: Use Xen specific TLB flush instead of the generic one.") Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the translation of a channel program fails, we may end up attempting
to clean up (free, unpin) stuff that never got translated (and allocated,
pinned) in the first place.
By adjusting the lengths of the chains accordingly (so the element that
failed, and all subsequent elements are excluded) cleanup activities
based on false assumptions can be avoided.
Let's make sure cp_free works properly after cp_prefetch returns with an
error by setting ch_len of a ccw chain to the number of the translated
CCWs on that chain.
Cc: stable@vger.kernel.org #v4.12+ Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com> Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com> Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com> Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20180423110113.59385-2-bjsdjshi@linux.vnet.ibm.com>
[CH: fixed typos] Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This causes warnings from cpufreq mutex code. This is also rather
unnecessary and ineffective. If we really want to prevent concurrent
unplug, we could take the unplug read lock but I don't see this being
critical.
Fixes: cd77b5ce208c ("powerpc/powernv/cpufreq: Fix the frequency read by /proc/cpuinfo") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kvm_read_guest() will eventually look up in kvm_memslots(), which requires
either to hold the kvm->slots_lock or to be inside a kvm->srcu critical
section.
In contrast to x86 and s390 we don't take the SRCU lock on every guest
exit, so we have to do it individually for each kvm_read_guest() call.
Provide a wrapper which does that and use that everywhere.
Note that ending the SRCU critical section before returning from the
kvm_read_guest() wrapper is safe, because the data has been *copied*, so
we don't need to rely on valid references to the memslot anymore.
Cc: Stable <stable@vger.kernel.org> # 4.8+ Reported-by: Jan Glauber <jan.glauber@caviumnetworks.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kvm_read_guest() will eventually look up in kvm_memslots(), which requires
either to hold the kvm->slots_lock or to be inside a kvm->srcu critical
section.
In contrast to x86 and s390 we don't take the SRCU lock on every guest
exit, so we have to do it individually for each kvm_read_guest() call.
Use the newly introduced wrapper for that.
Cc: Stable <stable@vger.kernel.org> # 4.12+ Reported-by: Jan Glauber <jan.glauber@caviumnetworks.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added fix for probing of spi-nor device non-zero chip selects. Set
MSPI_CDRAM_PCS (peripheral chip select) with spi master for MSPI
controller and not for MSPI/BSPI spi-nor master controller. Ensure
setting of cs bit in chip select register on chip select change.
Fixes: fa236a7ef24048 ("spi: bcm-qspi: Add Broadcom MSPI driver") Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the 32-bit device address only is supported for DMA. However,
starting from Intel Sunrisepoint PCH the DMA address of the device FIFO
can be 64-bit.
Change the respective variable to be compatible with DMA engine
expectations, i.e. to phys_addr_t.
Fixes: 34cadd9c1bcb ("spi: pxa2xx: Add support for Intel Sunrisepoint") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In snd_ctl_elem_add_compat(), the fields of the struct 'data' need to be
copied from the corresponding fields of the struct 'data32' in userspace.
This is achieved by invoking copy_from_user() and get_user() functions. The
problem here is that the 'type' field is copied twice. One is by
copy_from_user() and one is by get_user(). Given that the 'type' field is
not used between the two copies, the second copy is *completely* redundant
and should be removed for better performance and cleanup. Also, these two
copies can cause inconsistent data: as the struct 'data32' resides in
userspace and a malicious userspace process can race to change the 'type'
field between the two copies to cause inconsistent data. Depending on how
the data is used in the future, such an inconsistency may cause potential
security risks.
For above reasons, we should take out the second copy.
stub_probe() calls put_busid_priv() in an error path when device isn't
found in the busid_table. Fix it by making put_busid_priv() safe to be
called with null struct bus_id_priv pointer.
This problem happens when "usbip bind" is run without loading usbip_host
driver and then running modprobe. The first failed bind attempt unbinds
the device from the original driver and when usbip_host is modprobed,
stub_probe() runs and doesn't find the device in its busid table and calls
put_busid_priv(0 with null bus_id_priv pointer.
usbip-host 3-10.2: 3-10.2 is not in match_busid table... skip!
[ 367.359679] =====================================
[ 367.359681] WARNING: bad unlock balance detected!
[ 367.359683] 4.17.0-rc4+ #5 Not tainted
[ 367.359685] -------------------------------------
[ 367.359688] modprobe/2768 is trying to release lock (
[ 367.359689]
==================================================================
[ 367.359696] BUG: KASAN: null-ptr-deref in print_unlock_imbalance_bug+0x99/0x110
[ 367.359699] Read of size 8 at addr 0000000000000058 by task modprobe/2768
usbip_host updates device status without holding lock from stub probe,
disconnect and rebind code paths. When multiple requests to import a
device are received, these unprotected code paths step all over each
other and drive fails with NULL-ptr deref and use-after-free errors.
The driver uses a table lock to protect the busid array for adding and
deleting busids to the table. However, the probe, disconnect and rebind
paths get the busid table entry and update the status without holding
the busid table lock. Add a new finer grain lock to protect the busid
entry. This new lock will be held to search and update the busid entry
fields from get_busid_idx(), add_match_busid() and del_match_busid().
match_busid_show() does the same to access the busid entry fields.
get_busid_priv() changed to return the pointer to the busid entry holding
the busid lock. stub_probe(), stub_disconnect() and stub_device_rebind()
call put_busid_priv() to release the busid lock before returning. This
changes fixes the unprotected code paths eliminating the race conditions
in updating the busid entries.
After removing usbip_host module, devices it releases are left without
a driver. For example, when a keyboard or a mass storage device are
bound to usbip_host when it is removed, these devices are no longer
bound to any driver.
Fix it to run device_attach() from the module exit routine to restore
the devices to their original drivers. This includes cleanup changes
and moving device_attach() code to a common routine to be called from
rebind_store() and usbip_host_exit().
Device is left in the busid_table after unbind and rebind. Rebind
initiates usb bus scan and the original driver claims the device.
After rescan the device should be deleted from the busid_table as
it no longer belongs to usbip_host.
Fix it to delete the device after device_attach() succeeds.
proc_pid_cmdline_read() and environ_read() directly access the target
process' VM to retrieve the command line and environment. If this
process remaps these areas onto a file via mmap(), the requesting
process may experience various issues such as extra delays if the
underlying device is slow to respond.
Let's simply refuse to access file-backed areas in these functions.
For this we add a new FOLL_ANON gup flag that is passed to all calls
to access_remote_vm(). The code already takes care of such failures
(including unmapped areas). Accesses via /proc/pid/mem were not
changed though.
This was assigned CVE-2018-1120.
Note for stable backports: the patch may apply to kernels prior to 4.11
but silently miss one location; it must be checked that no call to
access_remote_vm() keeps zero as the last argument.
Revert commit 820da5357572 ("l2tp: fix missing print session offset
info"). The peer_offset parameter is removed.
Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preivous patch:
Btrfs: kill trans in run_delalloc_nocow and btrfs_cross_ref_exist
We avoid starting btrfs transaction and get this information from
fs_info->running_transaction directly.
When accessing running_transaction in check_delayed_ref, there's a
chance that current transaction will be freed by commit transaction
after the NULL pointer check of running_transaction is passed.
After looking all the other places using fs_info->running_transaction,
they are either protected by trans_lock or holding the transactions.
Fix this by using trans_lock and increasing the use_count.
Fixes: e4c3b2dcd144 ("Btrfs: kill trans in run_delalloc_nocow and btrfs_cross_ref_exist") CC: stable@vger.kernel.org # 4.14+ Signed-off-by: ethanwu <ethanwu@synology.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not need locking in xfrm_trans_queue because it is designed
to use per-CPU buffers. However, the original code incorrectly
used skb_queue_tail which takes the lock. This patch switches
it to __skb_queue_tail instead.
commit b60710ec7d7a ("scsi: aacraid: enable sending of TMFs from
aac_hba_send()") allows aac_hba_send() to send scsi commands, and TMF
requests, but the existing code only updates the iu_type for scsi
commands. For TMF requests we are sending an unknown iu_type to
firmware, which causes a fault.
Include iu_type prior to determining the validity of the command
Reported-by: Noah Misner <nmisner@us.ibm.com> Fixes: b60710ec7d7ab ("aacraid: enable sending of TMFs from aac_hba_send()") Fixes: 423400e64d377 ("aacraid: Include HBA direct interface") Tested-by: Noah Misner <nmisner@us.ibm.com>
cc: stable@vger.kernel.org Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Damir reported a breakage of SO_BINDTODEVICE for UDP sockets.
In absence of VRF devices, after commit fb74c27735f0 ("net:
ipv4: add second dif to udp socket lookups") the dif mismatch
isn't fatal anymore for UDP socket lookup with non null
sk_bound_dev_if, breaking SO_BINDTODEVICE semantics.
This changeset addresses the issue making the dif match mandatory
again in the above scenario.
Reported-by: Damir Mansurov <dnman@oktetlabs.ru> Fixes: fb74c27735f0 ("net: ipv4: add second dif to udp socket lookups") Fixes: 1801b570dd2a ("net: ipv6: add second dif to udp socket lookups") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ICMPv4, the checksum is calculated from the ICMP headers and data.
Since the ICMPv4 checksum doesn't cover the IP header, we can allow to
do L3 header re-write for this protocol.
Fixes: bdd66ac0aeed ('net/mlx5e: Disallow TC offloading of unsupported match/action combinations') Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 23aebdacb05d ("ipv6: Compute multipath hash for ICMP errors from offending packet") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Jakub Sitnicki <jkbs@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hyper-v transparent bonding should have used master_dev_link.
The netvsc device should look like a master bond device not
like the upper side of a tunnel.
This makes the semantics the same so that userspace applications
looking at network devices see the correct master relationshipship.
Fixes: 0c195567a8f6 ("netvsc: transparent VF management") Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of a dma_mapping_error, do not use wi->num_dma
as a parameter for dma unmap function because it's yet
to be set, and holds an out-of-date value.
Use actual value (local variable num_dma) instead.
Fixes: 34802a42b352 ("net/mlx5e: Do not modify the TX SKB") Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case modules are not configured, error out when tp->ops is null
and prevent later null pointer dereference.
Fixes: 33a48927c193 ("sched: push TC filter protocol creation into a separate function") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a regression at some point from the intended functionality of
commit f60c3704e87d ("bonding: Fix alb mode to only use first level
vlans.")
Given the return value vlan_get_encap_level() we need to store the nest
level of the bond device, and then compare the vlan's encap level to
this. Without this, this check always fails and learning packets are
never sent.
In addition, this same commit caused a regression in the behavior of
balance_alb, which requires learning packets be sent for all interfaces
using the slave's mac in order to load balance properly. For vlan's
that have not set a user mac, we can send after checking one bit.
Otherwise we need send the set mac, albeit defeating rx load balancing
for that vlan.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure multicast, broadcast, and zero mac's cannot be the output of rlb
updates, which should all be directed arps. Receive load balancing will be
collapsed if any of these happen, as the switch will broadcast.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tg3_free_consistent() calls dma_free_coherent() to free tp->hw_stats
under spinlock and can trigger BUG_ON() in vunmap() because vunmap()
may sleep. Fix it by removing the spinlock and relying on the
TG3_FLAG_INIT_COMPLETE flag to prevent race conditions between
tg3_get_stats64() and tg3_free_consistent(). TG3_FLAG_INIT_COMPLETE
is always cleared under tp->lock before tg3_free_consistent()
and therefore tg3_get_stats64() can safely access tp->hw_stats
under tp->lock if TG3_FLAG_INIT_COMPLETE is set.
Fixes: f5992b72ebe0 ("tg3: Fix race condition in tg3_get_stats64().") Reported-by: Zumeng Chen <zumeng.chen@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TCP repair sequence of operation is to first set the socket in
repair mode, then inject the TCP stats into the socket with repair
socket options, then call connect() to re-activate the socket. The
connect syscall simply returns and set state to ESTABLISHED
mode. As a result Fast Open is meaningless for TCP repair.
However allowing sendto() system call with MSG_FASTOPEN flag half-way
during the repair operation could unexpectedly cause data to be
sent, before the operation finishes changing the internal TCP stats
(e.g. MSS). This in turn triggers TCP warnings on inconsistent
packet accounting.
The fix is to simply disallow Fast Open operation once the socket
is in the repair mode.
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the bbr->idle_restart tracking was zeroing out the
bbr->idle_restart bit upon ACKs that did not SACK or ACK anything,
e.g. receiving incoming data or receiver window updates. In such
situations BBR would forget that this was a restart-from-idle
situation, and if the min_rtt had expired it would unnecessarily enter
PROBE_RTT (even though we were actually restarting from idle but had
merely forgotten that fact).
The fix is simple: we need to remember we are restarting from idle
until we receive a S/ACK for some data (a S/ACK for the first flight
of data we send as we are restarting).
This commit is a stable candidate for kernels back as far as 4.9.
When processing a duplicate cookie-echo chunk, for case 'D', sctp will
not process the param from this chunk. It means old asoc has nothing
to be updated, and the new temp asoc doesn't have the complete info.
So there's no reason to use the new asoc when creating the cookie-ack
chunk. Otherwise, like when auth is enabled for cookie-ack, the chunk
can not be set with auth, and it will definitely be dropped by peer.
This issue is there since very beginning, and we fix it by using the
old asoc instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Commit 1f45f78f8e51 ("sctp: allow GSO frags to access the chunk too"),
it held the chunk in sctp_ulpevent_make_rcvmsg to access it safely later
in recvmsg. However, it also added sctp_chunk_put in fail_mark err path,
which is only triggered before holding the chunk.
syzbot reported a use-after-free crash happened on this err path, where
it shouldn't call sctp_chunk_put.
This patch simply removes this call.
Fixes: 1f45f78f8e51 ("sctp: allow GSO frags to access the chunk too") Reported-by: syzbot+141d898c5f24489db4aa@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since sctp ipv6 socket also supports v4 addrs, it's possible to
compare two v4 addrs in pf v6 .cmp_addr, sctp_inet6_cmp_addr.
However after Commit 1071ec9d453a ("sctp: do not check port in
sctp_inet6_cmp_addr"), it no longer calls af1->cmp_addr, which
in this case is sctp_v4_cmp_addr, but calls __sctp_v6_cmp_addr
where it handles them as two v6 addrs. It would cause a out of
bounds crash.
syzbot found this crash when trying to bind two v4 addrs to a
v6 socket.
This patch fixes it by adding the process for two v4 addrs in
sctp_inet6_cmp_addr.
Fixes: 1071ec9d453a ("sctp: do not check port in sctp_inet6_cmp_addr") Reported-by: syzbot+cd494c1dd681d4d93ebb@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When auth is enabled for cookie-ack chunk, in sctp_inq_pop, sctp
processes auth chunk first, then continues to the next chunk in
this packet if chunk_end + chunk_hdr size < skb_tail_pointer().
Otherwise, it will go to the next packet or discard this chunk.
However, it missed the fact that cookie-ack chunk's size is equal
to chunk_hdr size, which couldn't match that check, and thus this
chunk would not get processed.
This patch fixes it by changing the check to chunk_end + chunk_hdr
size <= skb_tail_pointer().
Fixes: 26b87c788100 ("net: sctp: fix remote memory pressure from excessive queueing") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now sctp only delays the authentication for the normal cookie-echo
chunk by setting chunk->auth_chunk in sctp_endpoint_bh_rcv(). But
for the duplicated one with auth, in sctp_assoc_bh_rcv(), it does
authentication first based on the old asoc, which will definitely
fail due to the different auth info in the old asoc.
The duplicated cookie-echo chunk will create a new asoc with the
auth info from this chunk, and the authentication should also be
done with the new asoc's auth info for all of the collision 'A',
'B' and 'D'. Otherwise, the duplicated cookie-echo chunk with auth
will never pass the authentication and create the new connection.
This issue exists since very beginning, and this fix is to make
sctp_assoc_bh_rcv() follow the way sctp_endpoint_bh_rcv() does
for the normal cookie-echo chunk to delay the authentication.
While at it, remove the unused params from sctp_sf_authenticate()
and define sctp_auth_chunk_verify() used for all the places that
do the delayed authentication.
v1->v2:
fix the typo in changelog as Marcelo noticed.
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a92a08499b1f "r8169: improve runtime pm in general and
suspend unused ports" interfaces w/o link are runtime-suspended after
10s. On systems where drivers take longer to load this can lead to the
situation that the interface is runtime-suspended already when it's
initially brought up.
This shouldn't be a problem because rtl_open() resumes MAC/PHY.
However with at least one chip version the interface doesn't properly
come up, as reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199549
The vendor driver uses a delay to give certain chip versions some
time to resume before starting the PHY configuration. So let's do
the same. I don't know which chip versions may be affected,
therefore apply this delay always.
This patch was reported to fix the issue for RTL8168h.
I was able to reproduce the issue on an Asus H310I-Plus which also
uses a RTL8168h. Also in my case the patch fixed the issue.
Reported-by: Slava Kardakov <ojab@ojab.ru> Tested-by: Slava Kardakov <ojab@ojab.ru> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB_DEVICE_INTERFACE_NUMBER matching macro assumes that
the { vendorid, productid, interfacenumber } set uniquely
identifies one specific function. This has proven to fail
for some configurable devices. One example is the Quectel
EM06/EP06 where the same interface number can be either
QMI or MBIM, without the device ID changing either.
Fix by requiring the vendor-specific class for interface number
based matching. Functions of other classes can and should use
class based matching instead.
Fixes: 03304bcb5ec4 ("net: qmi_wwan: use fixed interface number matching") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an OVS_ATTR_NESTED attribute type is found while walking
through netlink attributes, we call nlattr_set() recursively
passing the length table for the following nested attributes, if
different from the current one.
However, once we're done with those sub-nested attributes, we
should continue walking through attributes using the current
table, instead of using the one related to the sub-nested
attributes.
we switch to the 'ovs_tunnel_key_lens' table on attribute #3,
and we don't switch back to 'ovs_key_lens' while setting
attributes #9 to #11 in the sequence. As OVS_KEY_ATTR_MPLS
evaluates to 21, and the array size of 'ovs_tunnel_key_lens' is
15, we also get this kind of KASan splat while accessing the
wrong table:
[ 7655.132484] The buggy address belongs to the variable:
[ 7655.138226] ovs_tunnel_key_lens+0xf0/0xffffffffffffd400 [openvswitch]
[ 7655.145507]
[ 7655.147166] Memory state around the buggy address:
[ 7655.152514] ffffffffc169eb80: 00 00 00 00 00 00 00 00 00 00 fa fa fa fa fa fa
[ 7655.160585] ffffffffc169ec00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 7655.168644] >ffffffffc169ec80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa fa
[ 7655.176701] ^
[ 7655.184372] ffffffffc169ed00: fa fa fa fa 00 00 00 00 fa fa fa fa 00 00 00 05
[ 7655.192431] ffffffffc169ed80: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
[ 7655.200490] ==================================================================
Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: 982b52700482 ("openvswitch: Fix mask generation for nested attributes.") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of writing a partial tls record we forgot to clear the
ctx->in_tcp_sendpages flag, causing some connections to stall.
Fixes: c212d2c7fc47 ("net/tls: Don't recursively call push_record during tls_write_space callbacks") Signed-off-by: Andre Tomt <andre@tomt.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tls_push_sg already does a loop over all sending sg's, so ignore
any tls_write_space notifications until we are done sending.
We then have to call the previous write_space to wake up
poll() waiters after we are done with the send loop.
Reported-by: Andre Tomt <andre@tomt.net> Signed-off-by: Dave Watson <davejwatson@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the x32 ABI, struct timeval has two 64-bit fields. However
the kernel currently interprets the user-space values used for
the SO_RCVTIMEO and SO_SNDTIMEO socket options as having a pair
of 32-bit fields.
When the seconds portion of the requested timeout is less than 2**32,
the seconds portion of the effective timeout is correct but the
microseconds portion is zero. When the seconds portion of the
requested timeout is zero and the microseconds portion is non-zero,
the kernel interprets the timeout as zero (never timeout).
Fix by using 64-bit time for SO_RCVTIMEO/SO_SNDTIMEO as required
for the ABI.
Fixes: 515c7af85ed9 ("x32: Use compat shims for {g,s}etsockopt") Reported-by: Gopal RajagopalSai <gopalsr83@gmail.com> Signed-off-by: Lance Richardson <lance.richardson.net@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally, a socket can not be freed/reused unless all its TX packets
left qdisc and were TX-completed. However connect(AF_UNSPEC) allows
this to happen.
With commit fc59d5bdf1e3 ("pkt_sched: fq: clear time_next_packet for
reused flows") we cleared f->time_next_packet but took no special
action if the flow was still in the throttled rb-tree.
Since f->time_next_packet is the key used in the rb-tree searches,
blindly clearing it might break rb-tree integrity. We need to make
sure the flow is no longer in the rb-tree to avoid this problem.
Fixes: fc59d5bdf1e3 ("pkt_sched: fq: clear time_next_packet for reused flows") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When application fails to pass flags in netlink TLV when replacing
existing skbmod action, the kernel will leak refcnt:
$ tc actions get action skbmod index 1
total acts 0
action order 0: skbmod pipe set smac 00:11:22:33:44:55
index 1 ref 1 bind 0
For example, at this point a buggy application replaces the action with
index 1 with new smac 00:aa:22:33:44:55, it fails because of zero flags,
however refcnt gets bumped:
$ tc actions get actions skbmod index 1
total acts 0
action order 0: skbmod pipe set smac 00:11:22:33:44:55
index 1 ref 2 bind 0
$
Tha patch fixes this by calling tcf_idr_release() on existing actions.
Fixes: 86da71b57383d ("net_sched: Introduce skbmod action") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx4 modify cq limits the coalescing time parameter and
coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.
Change type of sample-interval and adaptive_rx_coal parameters in mlx4
driver to u32 as the ethtool holds them as u32 and these parameters are
not limited due to mlx4 HW.
Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC') Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dual_mac mode packets arrived on one port should not be forwarded by
switch hw to another port. Only Linux Host can forward packets between
ports. The below test case (reported in [1]) shows that packet arrived on
one port can be leaked to anoter (reproducible with dual port evms):
- connect port 1 (eth0) to linux Host 0 and run tcpdump or Wireshark
- connect port 2 (eth1) to linux Host 1 with vlan 1 configured
- ping <IPx> from Host 1 through vlan 1 interface.
ARP packets will be seen on Host 0.
Issue happens because dual_mac mode is implemnted using two vlans: 1 (Port
1+Port 0) and 2 (Port 2+Port 0), so there are vlan records created for for
each vlan. By default, the ALE will find valid vlan record in its table
when vlan 1 tagged packet arrived on Port 2 and so forwards packet to all
ports which are vlan 1 members (like Port.
To avoid such behaviorr the ALE VLAN ID Ingress Check need to be enabled
for each external CPSW port (ALE_PORTCTLn.VID_INGRESS_CHECK) so ALE will
drop ingress packets if Rx port is not VLAN member.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, skb->len and skb->data_len are set to the page size, not
the packet size. This causes the frame check sequence to not be
located at the "end" of the packet resulting in ethernet frame check
errors. The driver does work currently, but stricter kernel facing
networking solutions like OpenVSwitch will drop these packets as
invalid.
These changes set the packet size correctly so that these errors no
longer occur. The length does not include the frame check sequence, so
that subtraction was removed.
Tested on Oracle/SUN Multithreaded 10-Gigabit Ethernet Network
Controller [108e:abcd] and validated in wireshark.
Signed-off-by: Rob Taglang <rob@taglang.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow some non-cached routes to use non-expired fnhe:
1. ip_del_fnhe: moved above and now called by find_exception.
The 4.5+ commit deed49df7390 expires fnhe only when caching
routes. Change that to:
1.1. use fnhe for non-cached local output routes, with the help
from (2)
1.2. allow __mkroute_input to detect expired fnhe (outdated
fnhe_gw, for example) when do_cache is false, eg. when itag!=0
for unicast destinations.
2. __mkroute_output: keep fi to allow local routes with orig_oif != 0
to use fnhe info even when the new route will not be cached into fnhe.
After commit 839da4d98960 ("net: ipv4: set orig_oif based on fib
result for local traffic") it means all local routes will be affected
because they are not cached. This change is used to solve a PMTU
problem with IPVS (and probably Netfilter DNAT) setups that redirect
local clients from target local IP (local route to Virtual IP)
to new remote IP target, eg. IPVS TUN real server. Loopback has
64K MTU and we need to create fnhe on the local route that will
keep the reduced PMTU for the Virtual IP. Without this change
fnhe_pmtu is updated from ICMP but never exposed to non-cached
local routes. This includes routes with flowi4_oif!=0 for 4.6+ and
with flowi4_oif=any for 4.14+).
3. update_or_create_fnhe: make sure fnhe_expires is not 0 for
new entries
Fixes: 839da4d98960 ("net: ipv4: set orig_oif based on fib result for local traffic") Fixes: d6d5e999e5df ("route: do not cache fib route info on local routes with oif") Fixes: deed49df7390 ("route: check and remove route cache when we get route") Cc: David Ahern <dsahern@gmail.com> Cc: Xin Long <lucien.xin@gmail.com> Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we set a bond slave's master to bridge via ioctl, we only check
the IFF_BRIDGE_PORT flag. Although we will find the slave's real master
at netdev_master_upper_dev_link() later, it already does some settings
and allocates some resources. It would be better to return as early
as possible.
v1 -> v2:
use netdev_master_upper_dev_get() instead of netdev_has_any_upper_dev()
to check if we have a master, because not all upper devs are masters,
e.g. vlan device.
Reported-by: syzbot+de73361ee4971b6e6f75@syzkaller.appspotmail.com Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use disable_irq_nosync() instead of disable_irq() as this might be
called in atomic context with netpoll.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit "8003c9ae204e: add APIC Timer periodic/oneshot mode VMX
preemption timer support", a Windows 10 guest has some erratic timer
spikes.
Here the results on a 150000 times 1ms timer without any load:
Before 8003c9ae204e | After 8003c9ae204e
Max 1834us | 86000us
Mean 1100us | 1021us
Deviation 59us | 149us
Here the results on a 150000 times 1ms timer with a cpu-z stress test:
Before 8003c9ae204e | After 8003c9ae204e
Max 32000us | 140000us
Mean 1006us | 1997us
Deviation 140us | 11095us
The root cause of the problem is starting hrtimer with an expiry time
already in the past can take more than 20 milliseconds to trigger the
timer function. It can be solved by forward such past timers
immediately, rather than submitting them to hrtimer_start().
In case the timer is periodic, update the target expiration and call
hrtimer_start with it.
v2: Check if the tsc deadline is already expired. Thank you Mika.
v3: Execute the past timers immediately rather than submitting them to
hrtimer_start().
v4: Rearm the periodic timer with advance_periodic_target_expiration() a
simpler version of set_target_expiration(). Thank you Paolo.
This fixes several bugs in the radix page fault handler relating to
the way large pages in the memory backing the guest were handled.
First, the check for large pages only checked for explicit huge pages
and missed transparent huge pages. Then the check that the addresses
(host virtual vs. guest physical) had appropriate alignment was
wrong, meaning that the code never put a large page in the partition
scoped radix tree; it was always demoted to a small page.
Fixing this exposed bugs in kvmppc_create_pte(). We were never
invalidating a 2MB PTE, which meant that if a page was initially
faulted in without write permission and the guest then attempted
to store to it, we would never update the PTE to have write permission.
If we find a valid 2MB PTE in the PMD, we need to clear it and
do a TLB invalidation before installing either the new 2MB PTE or
a pointer to a page table page.
This also corrects an assumption that get_user_pages_fast would set
the _PAGE_DIRTY bit if we are writing, which is not true. Instead we
mark the page dirty explicitly with set_page_dirty_lock(). This
also means we don't need the dirty bit set on the host PTE when
providing write access on a read fault.
[paulus@ozlabs.org - use mark_pages_dirty instead of
kvmppc_update_dirty_map]
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with NFS, which ignores sync on directory handles,
fsync on a directory handle is a noop for CIFS/SMB3.
Do not return an error on it. It breaks some database
apps otherwise.
Signed-off-by: Steve French <smfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some P3100 drives have a bug where they think WRRU (weighted round robin)
is always enabled, even though the host doesn't set it. Since they think
it's enabled, they also look at the submission queue creation priority. We
used to set that to MEDIUM by default, but that was removed in commit 81c1cd98351b. This causes various issues on that drive. Add a quirk to
still set MEDIUM priority for that controller.
tmu_read() in case of Exynos4210 might return error for out of bound
values. Current code ignores such value, what leads to reporting critical
temperature value. Add proper error code propagation to exynos_get_temp()
function.
When thermal sensor is not yet enabled, reading temperature might return
random value. This might even result in stopping system booting when such
temperature is higher than the critical value. Fix this by checking if TMU
has been actually enabled before reading the temperature.
This change fixes booting of Exynos4210-based board with TMU enabled (for
example Samsung Trats board), which was broken since v4.4 kernel release.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 9e4249b40340 ("thermal: exynos: Fix first temperature read after registering sensor") CC: stable@vger.kernel.org # v4.6+ Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeremy Cline correctly points out in rhbz#1514836 that a device where the
QCA rome chipset needs the USB_QUIRK_RESET_RESUME quirk, may also ship
with a different wifi/bt chipset in some configurations.
If that is the case then we are needlessly penalizing those other chipsets
with a reset-resume quirk, typically causing 0.4W extra power use because
this disables runtime-pm.
This commit moves the DMI table check to a btusb_check_needs_reset_resume()
helper (so that we can easily also call it for other chipsets) and calls
this new helper only for QCA_ROME chipsets for now.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Cc: stable@vger.kernel.org Cc: Jeremy Cline <jcline@redhat.com> Suggested-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f44cb4b19ed4 ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") is causing bluetooth to no longer work for several
people, see: https://bugzilla.redhat.com/show_bug.cgi?id=1568911
So lets revert it for now and try to find another solution for
devices which need the modified quirk.
Cc: stable@vger.kernel.org Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the next_freq field of struct sugov_policy is set to UINT_MAX,
it shouldn't be used for updating the CPU frequency (this is a
special "invalid" value), but after commit b7eaf1aab9f8 (cpufreq:
schedutil: Avoid reducing frequency of busy CPUs prematurely) it
may be passed as the new frequency to sugov_update_commit() in
sugov_update_single().
Fix that by adding an extra check for the special UINT_MAX value
of next_freq to sugov_update_single().
Fixes: b7eaf1aab9f8 (cpufreq: schedutil: Avoid reducing frequency of busy CPUs prematurely) Reported-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 4.12+ <stable@vger.kernel.org> # 4.12+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0847684cfc5f0 (PCI / PM: Simplify device wakeup settings code)
went too far and dropped the device_may_wakeup() check from
pci_enable_wake() which causes wakeup to be enabled during system
suspend, hibernation or shutdown for some PCI devices that are not
allowed by user space to wake up the system from sleep (or power off).
As a result of this, excessive power is drawn by some of the affected
systems while in sleep states or off.
Restore the device_may_wakeup() check in pci_enable_wake(), but make
sure that the PCI bus type's runtime suspend callback will not call
device_may_wakeup() which is about system wakeup from sleep and not
about device wakeup from runtime suspend.
USB controller ASM1042 stops working after commit de3ef1eb1cd0 (PM /
core: Drop run_wake flag from struct dev_pm_info).
The device in question is not power managed by platform firmware,
furthermore, it only supports PME# from D3cold:
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Before commit de3ef1eb1cd0, the device never gets runtime suspended.
After that commit, the device gets runtime suspended to D3hot, which can
not generate any PME#.
So pci_dev_run_wake() needs to check PME wakeup capability as its first
condition.
In addition, change wakeup flag passed to pci_target_state() from false
to true, because we want to find the deepest state different from D3cold
that the device can still generate PME#. In this case, it's D0 for the
device in question.
Fixes: de3ef1eb1cd0 (PM / core: Drop run_wake flag from struct dev_pm_info) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: 4.13+ <stable@vger.kernel.org> # 4.13+ Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by sanitizing pool before using it to index
zatm_dev->pool_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log