When a fan is controlled via linear fallback without cstate, we
shouldn't stop polling. Otherwise it won't be adjusted again and
keeps running at an initial crazy pace.
Fixes: 800efb4c2857 ("drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios")
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103356
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107447 Reported-by: Thomas Blume <thomas.blume@suse.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_kzalloc(), devm_kstrdup() and devm_kasprintf() all can
fail internal allocation and return NULL. Using any of the assigned
objects without checking is not safe. As this is early in the boot
phase and these allocations really should not fail, any failure here
is probably an indication of a more serious issue so it makes little
sense to try and rollback the previous allocated resources or try to
continue; but rather the probe function is simply exited with -ENOMEM.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 684284b64aae ("ARM: integrator: add MMCI device to IM-PD1") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using HMB the PCIe host driver allocates host_mem_desc_bufs using
dma_alloc_attrs() but frees them using dma_free_coherent(). Use the
correct dma_free_attrs() function to free the buffers.
The current driver accepts any videomode with pclk < 154MHz. This is not
correct, as with 1 lane and/or 1.62Mbps speed not all videomodes can be
supported.
Add code to reject modes that require more bandwidth that is available.
Initially DP0_SRCCTRL is set to a static value which includes
DP0_SRCCTRL_LANES_2 and DP0_SRCCTRL_BW27, even when only 1 lane of
1.62Gbps speed is used. DP1_SRCCTRL is configured to a magic number.
This patch changes the configuration as follows:
Configure DP0_SRCCTRL by using tc_srcctrl() which provides the correct
value.
DP1_SRCCTRL needs two bits to be set to the same value as DP0_SRCCTRL:
SSCG and BW27. All other bits can be zero.
cpuinfo_cur_freq gets current CPU frequency as detected by hardware
while scaling_cur_freq last known CPU frequency. Some platforms may not
allow checking the CPU frequency of an offline CPU or the associated
resources may have been released via cpufreq_exit when the CPU gets
offlined, in which case the policy would have been invalidated already.
If we attempt to get current frequency from the hardware, it may result
in hang or crash.
For example on Juno, I see:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000188
[0000000000000188] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 5 PID: 4202 Comm: cat Not tainted 4.20.0-08251-ga0f2c0318a15-dirty #87
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : scmi_cpufreq_get_rate+0x34/0xb0
lr : scmi_cpufreq_get_rate+0x34/0xb0
Call trace:
scmi_cpufreq_get_rate+0x34/0xb0
__cpufreq_get+0x34/0xc0
show_cpuinfo_cur_freq+0x24/0x78
show+0x40/0x60
sysfs_kf_seq_show+0xc0/0x148
kernfs_seq_show+0x44/0x50
seq_read+0xd4/0x480
kernfs_fop_read+0x15c/0x208
__vfs_read+0x60/0x188
vfs_read+0x94/0x150
ksys_read+0x6c/0xd8
__arm64_sys_read+0x24/0x30
el0_svc_common+0x78/0x100
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
---[ end trace 3d1024e58f77f6b2 ]---
So fix the issue by checking if the policy is invalid early in
__cpufreq_get before attempting to get the current frequency.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some kernels, like 4.19.13-300.fc29.x86_64 in fedora 29, fail with the
existing probe definition asking for the contents of result->name,
working when we ask for the 'filename' variable instead, so add a
fallback to that.
Now those tests are back working on fedora 29 systems with that kernel:
# perf test vfs_getname
65: Use vfs_getname probe to get syscall args filenames : Ok
66: Add vfs_getname probe to get syscall args filenames : Ok
67: Check open filename arg using perf trace + vfs_getname: Ok
#
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-klt3n0i58dfqttveti09q3fi@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Detect when the mac length of a GSO packet is greater than the maximum
packet size (9700 bytes) and disable GSO.
Signed-off-by: Daniel Axtens <dja@axtens.net> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[jwang: cherry pick for CVE-2018-1000026] Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If you take a GSO skb, and split it into packets, will the MAC
length (L2 + L3 + L4 headers + payload) of those packets be small
enough to fit within a given length?
Move skb_gso_mac_seglen() to skbuff.h with other related functions
like skb_gso_network_seglen() so we can use it, and then create
skb_gso_validate_mac_len to do the full calculation.
Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[jwang: cherry pick for CVE-2018-1000026] Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The intention in the previous patch was to only place the processor
tables in the .rodata section if big.Little was being built and we
wanted the branch target hardening, but instead (due to the way it
was tested) it ended up always placing the tables into the .rodata
section.
Although harmless, let's correct this anyway.
Fixes: 3a4d0c2172bc ("ARM: ensure that processor vtables is not lost after boot") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Szyprowski reported problems with CPU hotplug in current kernels.
This was tracked down to the processor vtables being located in an
init section, and therefore discarded after kernel boot, despite being
required after boot to properly initialise the non-boot CPUs.
Arrange for these tables to end up in .rodata when required.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Fixes: 383fb3ee8024 ("ARM: spectre-v2: per-CPU vtables to work around big.Little systems") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In big.Little systems, some CPUs require the Spectre workarounds in
paths such as the context switch, but other CPUs do not. In order
to handle these differences, we need per-CPU vtables.
We are unable to use the kernel's per-CPU variables to support this
as per-CPU is not initialised at times when we need access to the
vtables, so we have to use an array indexed by logical CPU number.
We use an array-of-pointers to avoid having function pointers in
the kernel's read/write .data section.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Allow the way we access members of the processor vtable to be changed
at compile time. We will need to move to per-CPU vtables to fix the
Spectre variant 2 issues on big.Little systems.
However, we have a couple of calls that do not need the vtable
treatment, and indeed cause a kernel warning due to the (later) use
of smp_processor_id(), so also introduce the PROC_TABLE macro for
these which always use CPU 0's function pointers.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Call the per-processor type check_bugs() method in the same way as we
do other per-processor functions - move the "processor." detail into
proc-fns.h.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Split out the lookup of the processor type and associated error handling
from the rest of setup_processor() - we will need to use this in the
secondary CPU bringup path for big.Little Spectre variant 2 mitigation.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move lookup_processor_type() out of the __init section so it is callable
from (eg) the secondary startup code during hotplug.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Tested-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In vfp_preserve_user_clear_hwstate, ufp_exc->fpinst2 gets assigned to
itself. It should actually be hwstate->fpinst2 that gets assigned to the
ufp_exc field.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sanitize user pointer given to __copy_to_user, both for standard version
and memcopy version of the user accessor.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Introduce C and asm helpers to sanitize user address, taking the
address range they target into account.
Use asm helper for existing sanitization in __copy_from_user().
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When Spectre mitigation is required, __put_user() needs to include
check_uaccess. This is already the case for put_user(), so just make
__put_user() an alias of put_user().
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A mispredicted conditional call to set_fs could result in the wrong
addr_limit being forwarded under speculation to a subsequent access_ok
check, potentially forming part of a spectre-v1 attack using uaccess
routines.
This patch prevents this forwarding from taking place, but putting heavy
barriers in set_fs after writing the addr_limit.
Porting commit c2f0ad4fc089cff8 ("arm64: uaccess: Prevent speculative use
of the current addr_limit").
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With Spectre-v1.1 mitigations, __put_user_error is pointless. In an attempt
to remove it, replace its references in frame setups with __put_user.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Copy events to user using __copy_to_user() rather than copy members of
individually with __put_user_error().
This has the benefit of disabling/enabling PAN once per event intead of
once per event member.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use __copy_to_user() rather than __put_user_error() for individual
members when saving VFP state.
This has the benefit of disabling/enabling PAN once per copied struct
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When setting a dummy iwmmxt context, create a local instance and
use __copy_to_user both cases whether iwmmxt is being used or not.
This has the benefit of disabling/enabling PAN once for the whole copy
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When saving the ARM integer registers, use __copy_to_user() to
copy them into user signal frame, rather than __put_user_error().
This has the benefit of disabling/enabling PAN once for the whole copy
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian reported a io hung issue when fsync(). It should be
triggered by following race condition.
data + post flush a flush
blk_flush_complete_seq
case REQ_FSEQ_DATA
blk_flush_queue_rq
issued to driver blk_mq_dispatch_rq_list
try to issue a flush req
failed due to NON-NCQ command
.queue_rq return BLK_STS_DEV_RESOURCE
request completion
req->end_io // doesn't check RESTART
mq_flush_data_end_io
case REQ_FSEQ_POSTFLUSH
blk_kick_flush
do nothing because previous flush
has not been completed
blk_mq_run_hw_queue
insert rq to hctx->dispatch
due to RESTART is still set, do nothing
To fix this, replace the blk_mq_run_hw_queue in mq_flush_data_end_io
with blk_mq_sched_restart to check and clear the RESTART flag.
It turns out that people do actually depend on the shebang string being
truncated, and on the fact that an interpreter (like perl) will often
just re-interpret it entirely to get the full argument list.
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&idev->info_lock);
lock(&mm->mmap_sem);
lock(&idev->info_lock);
lock(&mm->mmap_sem);
*** DEADLOCK ***
1 lock held by XXX/1910:
#0: (&idev->info_lock){+.+...}, at: [<ffffffffc0638a06>] uio_write+0x46/0x130 [uio]
uio_mmap has multiple fail paths to set return value to nonzero then
goto out. However, it always returns *0* from the *out* at end, and
this will mislead callers who check the return value of this function.
Fixes: 57c5f4df0a5a0ee ("uio: fix crash after the device is unregistered") CC: Xiubo Li <xiubli@redhat.com> Signed-off-by: Hailong Liu <liu.hailong6@zte.com.cn> Cc: stable <stable@vger.kernel.org> Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uio: Prevent device destruction while fds are open
The problem is the addition of spin_lock_irqsave in uio_write. This
leads to hitting uio_write -> copy_from_user -> _copy_from_user ->
might_fault and the logs filling up with sleeping warnings.
I also noticed some uio drivers allocate memory, sleep, grab mutexes
from callouts like open() and release and uio is now doing
spin_lock_irqsave while calling them.
Reported-by: Mike Christie <mchristi@redhat.com> CC: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent destruction of a uio_device while user space apps hold open
file descriptors to that device. Further, access to the 'info' member
of the struct uio_device is protected by spinlock. This is to ensure
stale pointers to data not under control of the UIO subsystem are not
dereferenced.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[4.14 change __poll_t to unsigned int] Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The perf_event_attr::task is 1 by default for first (tracking) event in
the session. Setting task=1 as default and adding task=0 for cases that
need it.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20170703145030.12903-16-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: "Rantala, Tommi T. (Nokia - FI/Espoo)" <tommi.t.rantala@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The caller of ndo_start_xmit may not already have called
skb_reset_mac_header. The returned value of skb_mac_header/eth_hdr
therefore can be in the wrong position and even outside the current skbuff.
This for example happens when the user binds to the device using a
PF_PACKET-SOCK_RAW with enabled qdisc-bypass:
int opt = 4;
setsockopt(sock, SOL_PACKET, PACKET_QDISC_BYPASS, &opt, sizeof(opt));
Since eth_hdr is used all over the codebase, the batadv_interface_tx
function must always take care of resetting it.
It is not allowed to use WARN* helpers on potential incorrect input from
the user or transient problems because systems configured as panic_on_warn
will reboot due to such a problem.
A NULL return value of __dev_get_by_index can be caused by various problems
which can either be related to the system configuration or problems
(incorrectly returned network namespaces) in other (virtual) net_device
drivers. batman-adv should not cause a (harmful) WARN in this situation and
instead only report it via a simple message.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface") Reported-by: syzbot+c764de0fcfadca9a8595@syzkaller.appspotmail.com Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check assumes that in transport mode, the first templates family
must match the address family of the policy selector.
Syzkaller managed to build a template using MODE_ROUTEOPTIMIZATION,
with ipv4-in-ipv6 chain, leading to following splat:
BUG: KASAN: stack-out-of-bounds in xfrm_state_find+0x1db/0x1854
Read of size 4 at addr ffff888063e57aa0 by task a.out/2050
xfrm_state_find+0x1db/0x1854
xfrm_tmpl_resolve+0x100/0x1d0
xfrm_resolve_and_create_bundle+0x108/0x1000 [..]
Problem is that addresses point into flowi4 struct, but xfrm_state_find
treats them as being ipv6 because it uses templ->encap_family is used
(AF_INET6 in case of reproducer) rather than family (AF_INET).
This patch inverts the logic: Enforce 'template family must match
selector' EXCEPT for tunnel and BEET mode.
In BEET and Tunnel mode, xfrm_tmpl_resolve_one will have remote/local
address pointers changed to point at the addresses found in the template,
rather than the flowi ones, so no oob read will occur.
con_fault() can transition the connection into STANDBY right after
ceph_con_keepalive() clears STANDBY in clear_standby():
libceph user thread ceph-msgr worker
ceph_con_keepalive()
mutex_lock(&con->mutex)
clear_standby(con)
mutex_unlock(&con->mutex)
mutex_lock(&con->mutex)
con_fault()
...
if KEEPALIVE_PENDING isn't set
set state to STANDBY
...
mutex_unlock(&con->mutex)
set KEEPALIVE_PENDING
set WRITE_PENDING
This triggers warnings in clear_standby() when either ceph_con_send()
or ceph_con_keepalive() get to clearing STANDBY next time.
I don't see a reason to condition queue_con() call on the previous
value of KEEPALIVE_PENDING, so move the setting of KEEPALIVE_PENDING
into the critical section -- unlike WRITE_PENDING, KEEPALIVE_PENDING
could have been a non-atomic flag.
As Jan Kara pointed out, this change was unsafe since it means we lose
the call to sync_mapping_buffers() in the nojournal case. The
original point of the commit was avoid taking the inode mutex (since
it causes a lockdep warning in generic/113); but we need the mutex in
order to call sync_mapping_buffers().
The proposed patch was to fix a syzbot complaint, but the problem can
also demonstrated via "kvm-xfstests -c nojournal generic/113".
Multiple solutions were discused in the e-mail thread, but none have
landed in the kernel as of this writing. Anyway, commit ad211f3e94b314 is absolutely the wrong way to suppress the lockdep, so
revert it.
Fixes: ad211f3e94b314a910d4af03178a0b52a7d1ee0a ("ext4: use ext4_write_inode() when fsyncing w/o a journal") Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ring buffer implementation in hid_debug_event() and hid_debug_events_read()
is strange allowing lost or corrupted data. After commit 717adfdaf147
("HID: debug: check length before copy_to_user()") it is possible to enter
an infinite loop in hid_debug_events_read() by providing 0 as count, this
locks up a system. Fix this by rewriting the ring buffer implementation
with kfifo and simplify the code.
This fixes CVE-2019-3819.
v2: fix an execution logic and add a comment
v3: use __set_current_state() instead of set_current_state()
Backport to v4.14: 2 tree-wide patches 6396bb22151 ("treewide: kzalloc() ->
kcalloc()") and a9a08845e9ac ("vfs: do bulk POLL* -> EPOLL* replacement")
are missing in v4.14 so cherry-pick relevant pieces.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1669187 Cc: stable@vger.kernel.org # v4.18+ Fixes: cd667ce24796 ("HID: use debugfs for events/reports dumping") Fixes: 717adfdaf147 ("HID: debug: check length before copy_to_user()") Signed-off-by: Vladis Dronov <vdronov@redhat.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function was unconditionally returning 0, and a caller would have to
rely on the returned fence pointer being NULL to detect errors. However,
the function vmw_execbuf_copy_fence_user() would expect a non-zero error
code in that case and would BUG otherwise.
So make sure we return a proper non-zero error code if the fence pointer
returned is NULL.
Some drivers use IEEE80211_KEY_FLAG_SW_MGMT_TX to indicate that management
frames need to be software encrypted. Since normal data packets are still
encrypted by the hardware, crypto_tx_tailroom_needed_cnt gets decremented
after key upload to hw. This can lead to passing skbs to ccmp_encrypt_skb,
which don't have the necessary tailroom for software encryption.
Change the code to add tailroom for encrypted management packets, even if
crypto_tx_tailroom_needed_cnt is 0.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When generating vdso-o32.lds & vdso-n32.lds for use with programs
running as compat ABIs under 64b kernels, we previously haven't included
the compiler flags that are supposedly common to all ABIs - ie. those in
the ccflags-vdso variable.
This is problematic in cases where we need to provide the -m%-float flag
in order to ensure that we don't attempt to use a floating point ABI
that's incompatible with the target CPU & ABI. For example a toolchain
using current gcc trunk configured --with-fp-32=xx fails to build a
64r6el_defconfig kernel with the following error:
Include $(ccflags-vdso) for the compat VDSO .lds builds, just as it is
included for the native VDSO .lds & when compiling objects for the
compat VDSOs. This ensures we consistently provide the -msoft-float flag
amongst others, avoiding the problem by ensuring we're agnostic to the
toolchain defaults.
Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Cc: linux-mips@vger.kernel.org Cc: Kevin Hilman <khilman@baylibre.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Maciej W . Rozycki <macro@linux-mips.org> Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accordingly to the documentation
---cut---
The GCR_ERROR_CAUSE.ERR_TYPE field and the GCR_ERROR_MULT.ERR_TYPE
fields can be cleared by either a reset or by writing the current
value of GCR_ERROR_CAUSE.ERR_TYPE to the
GCR_ERROR_CAUSE.ERR_TYPE register.
---cut---
Do exactly this. Original value of cm_error may be safely written back;
it clears error cause and keeps other bits untouched.
Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors") Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org # v4.3+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
debugfs_rename() needs to check that the dentries passed into it really
are valid, as sometimes they are not (i.e. if the return value of
another debugfs call is passed into this one.) So fix this up by
properly checking if the two parent directories are errors (they are
allowed to be NULL), and if the dentry to rename is not NULL or an
error.
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop failing
to deliver SIGHUP but always trying.
When the stack overflows delivery of SIGHUP fails and force_sigsegv is
called. Unfortunately because SIGSEGV is numerically higher than
SIGHUP next_signal tries again to deliver a SIGHUP.
From a quality of implementation standpoint attempting to deliver the
timer SIGHUP signal is wrong. We should attempt to deliver the
synchronous SIGSEGV signal we just forced.
We can make that happening in a fairly straight forward manner by
instead of just looking at the signal number we also look at the
si_code. In particular for exceptions (aka synchronous signals) the
si_code is always greater than 0.
That still has the potential to pick up a number of asynchronous
signals as in a few cases the same si_codes that are used
for synchronous signals are also used for asynchronous signals,
and SI_KERNEL is also included in the list of possible si_codes.
Still the heuristic is much better and timer signals are definitely
excluded. Which is enough to prevent all known ways for someone
sending a process signals fast enough to cause unexpected and
arguably incorrect behavior.
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop
failing to deliver SIGHUP but always trying.
Upon examination it turns out part of the problem is actually most of
the solution. Since 2.5 signal delivery has found all fatal signals,
marked the signal group for death, and queued SIGKILL in every threads
thread queue relying on signal->group_exit_code to preserve the
information of which was the actual fatal signal.
The conversion of all fatal signals to SIGKILL results in the
synchronous signal heuristic in next_signal kicking in and preferring
SIGHUP to SIGKILL. Which is especially problematic as all
fatal signals have already been transformed into SIGKILL.
Instead of dequeueing signals and depending upon SIGKILL to
be the first signal dequeued, first test if the signal group
has already been marked for death. This guarantees that
nothing in the signal queue can prevent a process that needs
to exit from exiting.
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545 Fixes: 3091141d7803 ("iio: adc: axp288: Fix the GPADC pin ...") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
intel_pmu_cpu_prepare() allocated memory for ->shared_regs among other
members of struct cpu_hw_events. This memory is released in
intel_pmu_cpu_dying() which is wrong. The counterpart of the
intel_pmu_cpu_prepare() callback is x86_pmu_dead_cpu().
Otherwise if the CPU fails on the UP path between CPUHP_PERF_X86_PREPARE
and CPUHP_AP_PERF_X86_STARTING then it won't release the memory but
allocate new memory on the next attempt to online the CPU (leaking the
old memory).
Also, if the CPU down path fails between CPUHP_AP_PERF_X86_STARTING and
CPUHP_PERF_X86_PREPARE then the CPU will go back online but never
allocate the memory that was released in x86_pmu_dying_cpu().
Make the memory allocation/free symmetrical in regard to the CPU hotplug
notifier by moving the deallocation to intel_pmu_cpu_dead().
This started in commit:
a7e3ed1e47011 ("perf: Add support for supplementary event registers").
In principle the bug was introduced in v2.6.39 (!), but it will almost
certainly not backport cleanly across the big CPU hotplug rewrite between v4.7-v4.15...
Reported-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> # With developer hat on Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> # With maintainer hat on Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: acme@kernel.org Cc: bp@alien8.de Cc: hpa@zytor.com Cc: jolsa@kernel.org Cc: kan.liang@linux.intel.com Cc: namhyung@kernel.org Cc: <stable@vger.kernel.org> Fixes: a7e3ed1e47011 ("perf: Add support for supplementary event registers"). Link: https://lkml.kernel.org/r/20181219165350.6s3jvyxbibpvlhtq@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ He Zhe: Fixes conflict caused by missing disable_counter_freeze which is
introduced since v4.20 af3bdb991a5cb. ] Signed-off-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential memory corruption and panic in loopback for IB_WR_SEND
variants.
The code blindly assumes the posted length will fit in the fetched rwqe,
which is not a valid assumption.
Fix by adding a limit test, and triggering the appropriate send completion
and putting the QP in an error state. This mimics the handling for
non-loopback QPs.
Fixes: 15703461533a ("IB/{hfi1, qib, rdmavt}: Move ruc_loopback to rdmavt") Cc: <stable@vger.kernel.org> #v4.20+ Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
The spec allows us to return NFS4ERR_SEQ_FALSE_RETRY if we notice that
the client is making a call that matches a previous (slot, seqid) pair
but that *isn't* actually a replay, because some detail of the call
doesn't actually match the previous one.
Catching every such case is difficult, but we may as well catch a few
easy ones. This also handles the case described in the previous patch,
in a different way.
The spec does however require us to catch the case where the difference
is in the rpc credentials. This prevents somebody from snooping another
user's replies by fabricating retries.
(But the practical value of the attack is limited by the fact that the
replies with the most sensitive data are READ replies, which are not
normally cached.)
Tested-by: Olga Kornievskaia <aglo@umich.edu> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Donald Buczek <buczek@molgen.mpg.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently our handling of 4.1+ requests without "cachethis" set is
confusing and not quite correct.
Suppose a client sends a compound consisting of only a single SEQUENCE
op, and it matches the seqid in a session slot (so it's a retry), but
the previous request with that seqid did not have "cachethis" set.
The obvious thing to do might be to return NFS4ERR_RETRY_UNCACHED_REP,
but the protocol only allows that to be returned on the op following the
SEQUENCE, and there is no such op in this case.
The protocol permits us to cache replies even if the client didn't ask
us to. And it's easy to do so in the case of solo SEQUENCE compounds.
So, when we get a solo SEQUENCE, we can either return the previously
cached reply or NFSERR_SEQ_FALSE_RETRY if we notice it differs in some
way from the original call.
Currently, we're returning a corrupt reply in the case a solo SEQUENCE
matches a previous compound with more ops. This actually matters
because the Linux client recently started doing this as a way to recover
from lost replies to idempotent operations in the case the process doing
the original reply was killed: in that case it's difficult to keep the
original arguments around to do a real retry, and the client no longer
cares what the result is anyway, but it would like to make sure that the
slot's sequence id has been incremented, and the solo SEQUENCE assures
that: if the server never got the original reply, it will increment the
sequence id. If it did get the original reply, it won't increment, and
nothing else that about the reply really matters much. But we can at
least attempt to return valid xdr!
Tested-by: Olga Kornievskaia <aglo@umich.edu> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Donald Buczek <buczek@molgen.mpg.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There still is a race window after the commit b027e2298bd588
("tty: fix data race between tty_init_dev and flush of buf"),
and we encountered this crash issue if receive_buf call comes
before tty initialization completes in tty_open and
tty->driver_data may be NULL.
it can be fixed by extending ldisc semaphore lock in tty_init_dev
to driver_data initialized completely after tty->ops->open(), but
this will lead to get lock on one function and unlock in some other
function, and hard to maintain, so fix this race only by checking
tty->driver_data when receiving, and return if tty->driver_data
is NULL, and n_tty_receive_buf_common maybe calls uart_unthrottle,
so add the same check.
Because the tty layer knows nothing about the driver associated with the
device, the tty layer can not do anything here, it is up to the tty
driver itself to check for this type of race. Fix up the serial driver
to correctly check to see if it is finished binding with the device when
being called, and if not, abort the tty calls.
[Description and problem report and testing from Li RongQing, I rewrote
the patch to be in the serial layer, not in the tty core - gregkh]
Reported-by: Li RongQing <lirongqing@baidu.com> Tested-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Wang Li <wangli39@baidu.com> Signed-off-by: Zhang Yu <zhangyu31@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Notice that the use of the bitwise OR operator '|' always leads to true
in this particular case, which seems a bit suspicious due to the context
in which this expression is being used.
Fix this by using bitwise AND operator '&' instead.
This bug was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Fixes: 6a6cd11d4e57 ("perf test: Add test for the sched tracepoint format fields") Link: http://lkml.kernel.org/r/20190122233439.GA5868@embeddedor Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The perf tool uses /proc/sys/kernel/perf_event_mlock_kb to determine how
large its ringbuffer mmap should be. This can be configured to arbitrary
values, which can be larger than the maximum possible allocation from
kmalloc.
When this is configured to a suitably large value (e.g. thanks to the
perf fuzzer), attempting to use perf record triggers a WARN_ON_ONCE() in
__alloc_pages_nodemask():
WARNING: CPU: 2 PID: 5666 at mm/page_alloc.c:4511 __alloc_pages_nodemask+0x3f8/0xbc8
Let's avoid this by checking that the requested allocation is possible
before calling kzalloc.
Reported-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20190110142745.25495-1-mark.rutland@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal injection testing crashed with a console log that said:
mce: [Hardware Error]: CPU 7: Machine Check Exception: f Bank 0: bd80000000100134
This caused a lot of head scratching because the MCACOD (bits 15:0) of
that status is a signature from an L1 data cache error. But Linux says
that it found it in "Bank 0", which on this model CPU only reports L1
instruction cache errors.
The answer was that Linux doesn't initialize "m->bank" in the case that
it finds a fatal error in the mce_no_way_out() pre-scan of banks. If
this was a local machine check, then this partially initialized struct
mce is being passed to mce_panic().
Fix is simple: just initialize m->bank in the case of a fatal error.
Fixes: 40c36e2741d7 ("x86/mce: Fix incorrect "Machine check from unknown source" message") Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: x86-ml <x86@kernel.org> Cc: stable@vger.kernel.org # v4.18 Note pre-v5.0 arch/x86/kernel/cpu/mce/core.c was called arch/x86/kernel/cpu/mcheck/mce.c Link: https://lkml.kernel.org/r/20190201003341.10638-1-tony.luck@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PCI uncore PMUs cannot be registered on an 8-socket system (HPE
Superdome Flex).
To understand which Socket the PCI uncore PMUs belongs to, perf retrieves
the local Node ID of the uncore device from CPUNODEID(0xC0) of the PCI
configuration space, and the mapping between Socket ID and Node ID from
GIDNIDMAP(0xD4). The Socket ID can be calculated accordingly.
The local Node ID is only available at bit 2:0, but current code doesn't
mask it. If a BIOS doesn't clear the rest of the bits, an incorrect Node ID
will be fetched.
Filter the Node ID by adding a mask.
Reported-by: Song Liu <songliubraving@fb.com> Tested-by: Song Liu <songliubraving@fb.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> # v3.7+ Fixes: 7c94ee2e0917 ("perf/x86: Add Intel Nehalem and Sandy Bridge-EP uncore support") Link: https://lkml.kernel.org/r/1548600794-33162-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled. However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.
The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case. So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.
Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:
1) /sys/devices/system/cpu/smt/control showed "on" instead of
"notsupported"; and
2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.
I'd propose that we instead consider #1 above to not actually be a
problem. Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later. So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).
The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.
So fix it by:
a) reverting the original "fix" and its followup fix:
b) changing vmx_vm_init() to query the actual current SMT state --
instead of the sysfs control value -- to determine whether the L1TF
warning is needed. This also requires the 'sched_smt_present'
variable to exported, instead of 'cpu_smt_control'.
Fixes: 73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS") Reported-by: Igor Mammedov <imammedo@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Joe Mario <jmario@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple code paths where an hrtimer may have been started to
emulate an L1 VMX preemption timer that can result in a call to free_nested
without an intervening L2 exit where the hrtimer is normally
cancelled. Unconditionally cancel in free_nested to cover all cases.
Embargoed until Feb 7th 2019.
Signed-off-by: Peter Shier <pshier@google.com> Reported-by: Jim Mattson <jmattson@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Reported-by: Felix Wilhelm <fwilhelm@google.com> Cc: stable@kernel.org
Message-Id: <20181011184646.154065-1-pshier@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. creates a device that holds a reference to the VM object (with a borrowed
reference, the VM's refcount has not been bumped yet)
2. initializes the device
3. transfers the reference to the device to the caller's file descriptor table
4. calls kvm_get_kvm() to turn the borrowed reference to the VM into a real
reference
The ownership transfer in step 3 must not happen before the reference to the VM
becomes a proper, non-borrowed reference, which only happens in step 4.
After step 3, an attacker can close the file descriptor and drop the borrowed
reference, which can cause the refcount of the kvm object to drop to zero.
This means that we need to grab a reference for the device before
anon_inode_getfd(), otherwise the VM can disappear from under us.
Emulation of certain instructions (VMXON, VMCLEAR, VMPTRLD, VMWRITE with
memory operand, INVEPT, INVVPID) can incorrectly inject a page fault
when passed an operand that points to an MMIO address. The page fault
will use uninitialized kernel stack memory as the CR2 and error code.
The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR
exit to userspace; however, it is not an easy fix, so for now just
ensure that the error code and CR2 are zero.
Embargoed until Feb 7th 2019.
Reported-by: Felix Wilhelm <fwilhelm@google.com> Cc: stable@kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the PCI code had recently added a file named 'revision' to every
PCI device. Fix this by renaming the aic94xx revision file to
aic_revision. This is safe to do for us because as far as I can tell,
there's nothing in userspace relying on the current aic94xx revision file
so it can be renamed without breaking anything.
Fixes: 702ed3be1b1b (PCI: Create revision file in sysfs) Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Presently when an error is encountered during probe of the cxlflash
adapter, a deadlock is seen with cpu thread stuck inside
cxlflash_remove(). Below is the trace of the deadlock as logged by
khungtaskd:
cxlflash 0006:00:00.0: cxlflash_probe: init_afu failed rc=-16
INFO: task kworker/80:1:890 blocked for more than 120 seconds.
Not tainted 5.0.0-rc4-capi2-kexec+ #2
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/80:1 D 0 890 2 0x00000808
Workqueue: events work_for_cpu_fn
Call Trace:
0x4d72136320 (unreliable)
__switch_to+0x2cc/0x460
__schedule+0x2bc/0xac0
schedule+0x40/0xb0
cxlflash_remove+0xec/0x640 [cxlflash]
cxlflash_probe+0x370/0x8f0 [cxlflash]
local_pci_probe+0x6c/0x140
work_for_cpu_fn+0x38/0x60
process_one_work+0x260/0x530
worker_thread+0x280/0x5d0
kthread+0x1a8/0x1b0
ret_from_kernel_thread+0x5c/0x80
INFO: task systemd-udevd:5160 blocked for more than 120 seconds.
The deadlock occurs as cxlflash_remove() is called from cxlflash_probe()
without setting 'cxlflash_cfg->state' to STATE_PROBED and the probe thread
starts to wait on 'cxlflash_cfg->reset_waitq'. Since the device was never
successfully probed the 'cxlflash_cfg->state' never changes from
STATE_PROBING hence the deadlock occurs.
We fix this deadlock by setting the variable 'cxlflash_cfg->state' to
STATE_PROBED in case an error occurs during cxlflash_probe() and just
before calling cxlflash_remove().
Cc: stable@vger.kernel.org Fixes: c21e0bbfc485("cxlflash: Base support for IBM CXL Flash Adapter") Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The send_xchar() and tiocmset() tty operations are optional. Add the
missing sanity checks to prevent user-space triggerable NULL-pointer
dereferences.
Fixes: 6b9ad1c742bf ("staging: speakup: add send_xchar, tiocmset and input functionality for tty") Cc: stable <stable@vger.kernel.org> # 4.13 Cc: Okash Khawaja <okash.khawaja@gmail.com> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
power off the phy should be done before populate the phy. Otherwise,
am335x_init() could be called by the phy owner to power on the phy first,
then am335x_phy_probe() turns off the phy again without the caller knowing
it.
Fixes: 2fc711d76352 ("usb: phy: am335x: Enable USB remote wakeup using PHY wakeup") Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems or VMs where multiple devices share a single DevID
(because they sit behind a PCI bridge, or because the HW is
broken in funky ways), we reuse the save its_device structure
in order to reflect this.
It turns out that there is a distinct lack of locking when looking
up the its_device, and two device being probed concurrently can result
in double allocations. That's obviously not nice.
A solution for this is to have a per-ITS mutex that serializes device
allocation.
A similar issue exists on the freeing side, which can run concurrently
with the allocation. On top of now taking the appropriate lock, we
also make sure that a shared device is never freed, as we have no way
to currently track the life cycle of such object.
projects / users / jedix / linux-maple.git / log