Arnd Bergmann [Mon, 13 Feb 2023 14:47:21 +0000 (15:47 +0100)]
Merge tag 'qcom-arm64-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
More Qualcomm ARM64 DT updates for 6.3
The new Qualcomm QDU1000 and QRU1000 platforms, and the IDP device on
these are introduced. New support for a couple of USB modem sticks from
THWC are introduced, so is support for Xiaomi Mi Pad 5 Pro and the Pro
SKU of the Herobrine device.
The Core Bus Fabric (CBF) is introduced on MSM8996. Interconnect paths
for UFS are also described.
A few fixes related to the power-grid of herobrine, on SC7280, are
introduced.
QFPROM is introduced on IPQ8074 and Interconnect providers are added for
SDM670.
On SDM845 the duplicated wcd9340 audio coded description is moved from
devices to a common file, audio devices are added to the OnePlus 6 and
6T.
On SM6115 debug UART, SMP2P, watchdog nodes are introduced, and the
platform is switched to use #address/size-cells of 2, in line with most
other platforms.
Camera control interface and clock controllers are added for SM6350, and
the CCI interface is enabled on the Fairphone FP4.
On SM8350 the interconnect reference of SDHCI controller is corrected,
DSI1 PHY clocks are properly described as sources for the Display clock
controller and DSI1 is wired up to the display controller.
The firmware paths are corrected for the Sony Xperia Nagara platform.
The GPR bus, audio servic3es and LPASS pinctrl nodes are added for the
SM8550 platform. Additionally a few small typos/errors are corrected.
gpio-ranges are corrected across MSM8953, SM6115 and SC8280XP and a
range of DT validation issues are corrected.
* tag 'qcom-arm64-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (81 commits)
arm64: dts: qcom: sc7280: Power herobrine's 3.3 eDP/TS rail more properly
arm64: dts: qcom: pmk8550: fix PON compatible
arm64: dts: qcom: sm8550: fix DSI controller compatible
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on evoker
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on villager
arm64: dts: qcom: sc7280: Add 3ms ramp to herobrine's pp3300_left_in_mlb
arm64: dts: qcom: sc7280: On QCard, regulator L3C should be 1.8V
arm64: dts: qcom: sc8280xp: correct LPASS GPIO gpio-ranges
arm64: dts: qcom: msm8992-lg-bullhead: Enable regulators
arm64: dts: qcom: sm6115: correct TLMM gpio-ranges
arm64: dts: qcom: msm8953: correct TLMM gpio-ranges
arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM and MPSS memory regions
arm64: dts: qcom: sm8350-hdk: correct LT9611 pin function
arm64: dts: qcom: sm8350-hdk: align pin config node names with bindings
arm64: dts: qcom: sm6350: Use specific qmpphy compatible
arm64: dts: qcom: sm6115: Add smp2p nodes
arm64: dts: qcom: sm7225-fairphone-fp4: Enable CCI busses
arm64: dts: qcom: sm6350: Add CCI nodes
arm64: dts: qcom: sm6350: Add camera clock controller
dt-bindings: clock: add QCOM SM6350 camera clock bindings
...
Arnd Bergmann [Mon, 13 Feb 2023 14:44:37 +0000 (15:44 +0100)]
Merge tag 'qcom-dts-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
More Qualcomm ARM32 DTS updates for 6.3
This adds backlight, notification LED, vibrator, volume keys and hall
sensor to the OnePlus One, and provides a range of Devicetree validation
fixes across various platforms.
* tag 'qcom-dts-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (22 commits)
ARM: dts: qcom: align OPP table names with DT schema
ARM: dts: qcom: msm8974-oneplus-bacon: Add notification LED
ARM: dts: qcom: msm8974-oneplus-bacon: Add backlight
ARM: dts: qcom: msm8974-oneplus-bacon: Add volume keys and hall sensor
ARM: dts: qcom: msm8974-oneplus-bacon: Add vibrator
ARM: dts: qcom: pm8941: Add vibrator node
ARM: dts: qcom: sdx55: correct TLMM gpio-ranges
dt-bindings: arm: qcom: add the sa8775p-ride board
ARM: dts: qcom: apq8064: add second DSI host and PHY
ARM: dts: qcom: apq8060-dragonboard: align MPP pin node names with DT schema
dt-bindings: arm: qcom: Add Xiaomi Mi Pad 5 Pro (xiaomi-elish)
ARM: dts: qcom-sdx65: align RPMh regulator nodes with bindings
ARM: dts: qcom-sdx55: align RPMh regulator nodes with bindings
ARM: dts: qcom: use "okay" for status
ARM: dts: qcom: sdx65: Add Qcom SMMU-500 as the fallback for IOMMU node
ARM: dts: qcom: sdx55: Add Qcom SMMU-500 as the fallback for IOMMU node
ARM: dts: qcom: apq8064: use hdmi_phy for the MMCC's hdmipll clock
ARM: dts: qcom: apq8064: add #clock-cells to the HDMI PHY node
ARM: dts: qcom: ipq8064: move reg-less nodes outside soc node
dt-bindings: qcom: Document msm8916-thwc-uf896 and ufi001c
...
Arnd Bergmann [Mon, 13 Feb 2023 14:38:57 +0000 (15:38 +0100)]
Merge tag 'samsung-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v6.3, part two
Several cleanups pointed out by `make dtbs_check`:
1. Align LED status node name with bindings.
2. Drop redundant properties.
3. Move i2c-gpio node out of soc to top-level, as soc node is expected
to have only MMIO nodes.
4. Correct SPI NOR flash compatible in SMDK5250 and SMDKv310.
5. Align GPIO property names in WM1811-family codec nodes with bindings.
6. Correct MAX98090 codec DAI cells in Snow.
* tag 'samsung-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: correct max98090 DAI argument in Snow
ARM: dts: s5pv210: add "gpios" suffix to wlf,ldo1ena on Aries
ARM: dts: exynos: add "gpios" suffix to wlf,ldo1ena on Arndale
ARM: dts: exynos: add "gpios" suffix to wlf,ldo1ena on Midas
ARM: dts: exynos: correct SPI nor compatible in SMDK5250
ARM: dts: exynos: correct SPI nor compatible in SMDKv310
ARM: dts: exynos: move I2C10 out of soc node on Arndale
ARM: dts: exynos: drop redundant address/size cells from I2C10 on Arndale
ARM: dts: exynos: drop default status from I2C10 on Arndale
ARM: dts: exynos: align status led name with bindings on Origen4210
Arnd Bergmann [Thu, 9 Feb 2023 13:04:19 +0000 (14:04 +0100)]
Merge tag 'at91-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 device tree updates for 6.3 #2
It contains:
- cleanups arround flexcom nodes on SAM9X60 SoC as follows:
- preserve same ID for flexcoms and the embedded nodes (e.g. flx4
will embed uart4, spi4, i2c4 but not e.g. uart1, spi2, i2c3);
- SoC specific bindings were moved from board specific file to SoC
specific file
- DMA bindings for all flexcom nodes were added
- SoC file was filled with missing flexcom nodes
- new SAM9X60 Curiosity board that contains 1 uSDcard interface, 1 SDcard
interface, 1 USB device interface, 2 USB Type-A interfaces, 2 CAN
interfaces, 1 10/100 Ethernet interface, 1 LCD RGB666 interface,
1 Gb DDR2, 4 Gb NAND Flash, 2Kb EEPROM, leds, button, power
regulators, UART and JTAG connectors
* tag 'at91-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60 curiosity board
dt-bindings: arm: at91: Add info on sam9x60 curiosity
ARM: dts: at91: sam9x60: Add missing flexcom definitions
ARM: dts: at91: sam9x60: Add DMA bindings for the flexcom nodes
ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sam9x60: fix spi4 node
ARM: dts: at91: sam9x60: move flexcom definitions
ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions
Douglas Anderson [Wed, 8 Feb 2023 00:36:10 +0000 (16:36 -0800)]
arm64: dts: qcom: sc7280: Power herobrine's 3.3 eDP/TS rail more properly
This is the equivalent of commit f5b4811e8758 ("arm64: dts: qcom:
sc7180: Add trogdor eDP/touchscreen regulator off-on-time") and commit 23ff866987de ("arm64: dts: qcom: sc7180: Start the trogdor
eDP/touchscreen regulator on"), but for herobrine instead of trogdor.
The motivations for herobrine are the same as for trogdor.
NOTES:
* Currently for herobrine all boards are eDP, not MIPI. If/when we
have herobrine derivatives that are MIPI they we can evaluate
whether the same off-on-delay makes sense for them. For trogdor we
didn't add the delay to MIPI panels because the problem was found
late and nobody had complained about it. For herobrine defaulting to
assuming the same 500ms makes sense and if we find we need to
optimize later we can.
* Currently there are no oddball herobrine boards like homestar where
the panel really likes to be power cycled. If we have an oddball
board it will need to split the eDP and touchscreen rail anyway
(like homestar did) and we'll have to delete the "regulator-boot-on"
from that board.
Douglas Anderson [Tue, 7 Feb 2023 02:48:16 +0000 (18:48 -0800)]
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on evoker
On older revisions of evoker, the touchscreen was either
non-functional or needed special hardware magic to get it talking
properly. It's been decided that the proper way going forward is to
use L3C to power some buffers on the QCard and then configure the
touchscreens for 1.8V. Let's do that.
Note that this is safe to do even on older revs even if it might not
make the touchscreen work there (because they didn't have a properly
stuffed QCard). As talked about in the patch ("arm64: dts: qcom:
sc7280: On QCard, regulator L3C should be 1.8V") the L3C regulator
didn't go anywhere at all on older revs.
This patch relies on the patch ("HID: i2c-hid: goodix: Add
mainboard-vddio-supply") in order to function properly. Without that
patch this one won't do any harm but it won't actually accomplish its
goal.
Douglas Anderson [Tue, 7 Feb 2023 02:48:12 +0000 (18:48 -0800)]
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on villager
On never revs of sc7280-herobrine-villager (rev2+) the L3C rail is
provided to the touchscreen as the IO voltage rail. Let's add it in
the device tree.
NOTE: Even though this is only really needed on rev2+ villagers (-rev0
had non-functioning touchscreen and -rev1 had some hacky hardware
magic), it doesn't actually hurt to do this for old villager revs. As
talked about in the patch ("arm64: dts: qcom: sc7280: On QCard,
regulator L3C should be 1.8V") the L3C regulator didn't go anywhere at
all on older revs. That means that turning it on for older revs
doesn't hurt other than drawing a tiny bit of extra power. Since -rev0
and -rev1 villagers will never make it to real customers and it's nice
not to have too many old device trees, the better tradeoff seems to be
to enable it everywhere.
Douglas Anderson [Tue, 7 Feb 2023 02:48:11 +0000 (18:48 -0800)]
arm64: dts: qcom: sc7280: Add 3ms ramp to herobrine's pp3300_left_in_mlb
The "pp3300_left_in_mlb" rail on herobrine eventually connects up to
"vreg_edp_3p3" on the qcard. On several herobrine designs this rail
has been measured to need more than 1ms to turn on.
While technically a herobrine derivative (defined as anyone including
the "herobrine.dtsi") could change the board to make the rail rise
faster or slower, the fact that two boards (evoker and villager) both
measured it as taking more than 1ms implies that it's probably going
to be the norm. Thus, let's add a "regulator-enable-ramp-delay"
straight into the herobrine.dtsi to handle this. If a particular
derivative board needs a faster or slower one then they can override
it, though that feels unlikely.
While we measured something a bit over 1ms, we'll choose 3ms to give
us a tiny bit of margin. This isn't a rail that turns off and on all
the time anyway and 3ms is nothing compared to the total amount of
time to power on a panel.
Douglas Anderson [Tue, 7 Feb 2023 02:48:10 +0000 (18:48 -0800)]
arm64: dts: qcom: sc7280: On QCard, regulator L3C should be 1.8V
On the first sc7280 QCards the L3C rail was never really used for
anything. Stuffing options on the QCard meant that the QCard itself
didn't use this rail for anything. This rail did get sent to the
mainboard, but no existing mainboards ever did anything with it other
that route it to a testpoint.
On later sc7280 QCards, the L3C rail was repurposed. Instead of being
a (nominally) 3.3V rail, it was decided to make it a 1.8V rail. It is
now provided to the display connector (which might route it to the
touchscreen) and also used to power some buffers relating to
touchscreen IO. This rail is getting the additional tag "ts_avccio",
though some places still refer to it as "vreg_l3c_3p0" despite the
fact that the name now specifies the wrong voltage.
Since it never hurts for this rail to be 1.8V (even on old QCards /
old boards), let's just change it to 1.8V across the board and add the
extra "ts_avccio" moniker as a label in the device tree.
Future patches will start using this rail in their touchscreens.
Jamie Douglass [Thu, 2 Feb 2023 05:48:19 +0000 (16:48 +1100)]
arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM and MPSS memory regions
The memory region reserved by a previous commit (see fixes tag below)
overlaps with the SMEM and MPSS memory regions, causing error messages in
dmesg:
OF: reserved mem: OVERLAP DETECTED!
reserved@5000000 (0x0000000005000000--0x0000000007200000)
overlaps with smem_region@6a00000
(0x0000000006a00000--0x0000000006c00000)
This patch resolves both of these by splitting the previously reserved
memory region into two sections either side of the SMEM region and by
cutting off the second memory region to 0x7000000.
Luca Weiss [Mon, 23 Jan 2023 13:29:51 +0000 (14:29 +0100)]
arm64: dts: qcom: sm6350: Use specific qmpphy compatible
The sc7180 phy compatible works fine for some cases, but it turns out
sm6350 does need proper phy configuration in the driver, so use the
newly added sm6350 compatible.
Because the sm6350 compatible is using the new binding, we need to
change the node quite a bit to match it.
This fixes qmpphy init when no USB cable is plugged in during bootloader
stage.
Luca Weiss [Fri, 20 Jan 2023 13:13:46 +0000 (14:13 +0100)]
arm64: dts: qcom: sm6350: Add CCI nodes
Add nodes for the two CCI blocks found on SM6350.
The first contains two i2c busses and while the second one might also
contains two busses, the downstream kernel only has one configured, and
some boards use the GPIOs for the potential cci1_i2c1 one other
purposes, so leave that one unconfigured.
qcom-apq8060-dragonboard.dtb: mpps@50: cm3605-mpps-state: 'oneOf' conditional failed, one must be fixed:
'mpp5' does not match any of the regexes: '-pins$', 'pinctrl-[0-9]+'
Andrew Halaney [Mon, 30 Jan 2023 15:48:22 +0000 (09:48 -0600)]
arm64: dts: qcom: sa8540p-ride: Fix some i2c pinctrl settings
Some of the pinctrl groups were invalid for the selected pins. Select
the proper qup group to fix these warnings:
[ 6.523566] sc8280xp-tlmm f100000.pinctrl: invalid group "gpio135" for function "qup15"
[ 6.535042] sc8280xp-tlmm f100000.pinctrl: invalid group "gpio136" for function "qup15"
[ 6.597536] sc8280xp-tlmm f100000.pinctrl: invalid group "gpio158" for function "qup15"
[ 6.597544] sc8280xp-tlmm f100000.pinctrl: invalid group "gpio159" for function "qup15"
[ 6.597991] sc8280xp-tlmm f100000.pinctrl: invalid group "gpio0" for function "qup15"
[ 6.597996] sc8280xp-tlmm f100000.pinctrl: invalid group "gpio1" for function "qup15"
Abel Vesa [Fri, 27 Jan 2023 13:14:41 +0000 (15:14 +0200)]
arm64: dts: qcom: sm8550: Fix the aoss_qmp node name
The proper name for it is power-management. Currently, with the node
name being power-controller, the bindings check fails due to the
property #power-domain-cells missing.
Fixes: ffc50b2d3828 ("arm64: dts: qcom: Add base SM8550 dtsi") Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230127131441.1157679-1-abel.vesa@linaro.org
Populate the audio devices found on the OnePlus 6 and 6T using the
sdm845-sndcard driver.
Both devices have the earpiece and headphone jack connected to the
WCD9341 codec. The OnePlus 6 uses the MAX98927 speaker codec which is
already supported upstream. The OnePlus 6T uses a currently unsupported
TFA9894 codec.
Two internal microphones are supported, as well as an external headset
mic. Each DAI link is expected to be used for a single device.
Alsa UCM2 configs for this setup can be found here, they are not yet
upstream and include support for call audio which is missing in this
patch
Clock for WCD9340 is coming from the SoC and is the same in all users,
so move it to common file to reduce the code duplication (which still
allows further customizations per board).
Pin configuration fow WCD9340 is the same in all users, so move it to
common file to reduce the code duplication (which still allows further
customizations per board).
Krzysztof Kozlowski [Mon, 23 Jan 2023 08:42:58 +0000 (09:42 +0100)]
arm64: dts: qcom: sdm845: move codec to separate file
Re-organize SDM845 audio codec into separate, audio DTSI which
should be included and customized by the SDM845 boards wanting audio.
The codec node is anyway not a property of the SoC, but the boards.
On all others boards not using audio, keep the Slimbus node disabled as
it is empty.
There is dedicated compatible for Lenovo Yoga C630 sound card
(documented in bindings and used by Linux driver), so use it along with
a generic sound card fallback. The device is actually fully compatible
with the generic one.
Robert Marko [Mon, 23 Jan 2023 10:16:31 +0000 (11:16 +0100)]
arm64: dts: qcom: ipq8074: add QFPROM node
IPQ8074 has efuses like other Qualcomm SoC-s that are required for
determining various HW quirks which will be required later for CPR etc,
so lets add the QFPROM node for start.
Individidual fuses will be added as they are required.
Signed-off-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Kathiravan T <quic_kathirav@quicinc.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230123101631.475712-2-robimarko@gmail.com
Johan Hovold [Mon, 23 Jan 2023 10:16:07 +0000 (11:16 +0100)]
arm64: dts: qcom: sm8550: fix USB-DP PHY resets
The USB-DP PHY resets have been switched.
Fixes: 7f7e5c1b037f ("arm64: dts: qcom: sm8550: Add USB PHYs and controller nodes") Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230123101607.2413-1-johan+linaro@kernel.org
Dmitry Baryshkov [Fri, 20 Jan 2023 06:14:15 +0000 (08:14 +0200)]
arm64: dts: qcom: msm8996 switch from RPM_SMD_BB_CLK1 to RPM_SMD_XO_CLK_SRC
The vendor kernel uses RPM_SMD_XO_CLK_SRC clock as an CXO clock rather
than using the RPM_SMD_BB_CLK1 directly. Follow this example and switch
msm8996.dtsi to use RPM_SMD_XO_CLK_SRC clock instead of RPM_SMB_BB_CLK1.
Fixes: 2b8c9c77c268 ("arm64: dts: qcom: msm8996: convert xo_board to RPM_SMD_BB_CLK1") Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230120061417.2623751-7-dmitry.baryshkov@linaro.org
projects / linux.git / log