fuse_dev_splice_write() reads pipe->buffers to determine the size of
'bufs' array before taking the pipe_lock(). This is not safe as
another thread might change the 'pipe->buffers' between the allocation
and taking the pipe_lock(). So we end up with too small 'bufs' array.
Move the bufs allocations inside pipe_lock()/pipe_unlock() to fix this.
WARNING: possible irq lock inversion dependency detected
CPU 0/KVM/10284 just changed the state of lock: 000000000d538a88 (&st->lock){+...}, at:
speculative_store_bypass_update+0x10b/0x170
but this lock was taken by another, HARDIRQ-safe lock
in the past:
(&(&sighand->siglock)->rlock){-.-.}
and interrupts could create inverse lock ordering between them.
In svm_vcpu_run() speculative_store_bypass_update() is called with
interupts enabled via x86_virt_spec_ctrl_set_guest/host().
This is actually a false positive, because GIF=0 so interrupts are
disabled even if IF=1; however, we can easily move the invocations of
x86_virt_spec_ctrl_set_guest/host() into the interrupt disabled region to
cure it, and it's a good idea to keep the GIF=0/IF=1 area as small
and self-contained as possible.
Fixes: 1f50ddb4f418 ("x86/speculation: Handle HT correctly on AMD") Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Borislav Petkov <bp@suse.de> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: kvm@vger.kernel.org Cc: x86@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two users have reported [1] that they have an "extremely unlikely" system
with more than MAX_PA/2 memory and L1TF mitigation is not effective.
Make the warning more helpful by suggesting the proper mem=X kernel boot
parameter to make it effective and a link to the L1TF document to help
decide if the mitigation is worth the unusable RAM.
Two users have reported [1] that they have an "extremely unlikely" system
with more than MAX_PA/2 memory and L1TF mitigation is not effective. In
fact it's a CPU with 36bits phys limit (64GB) and 32GB memory, but due to
holes in the e820 map, the main region is almost 500MB over the 32GB limit:
Suggestions to use 'mem=32G' to enable the L1TF mitigation while losing the
500MB revealed, that there's an off-by-one error in the check in
l1tf_select_mitigation().
l1tf_pfn_limit() returns the last usable pfn (inclusive) and the range
check in the mitigation path does not take this into account.
Instead of amending the range check, make l1tf_pfn_limit() return the first
PFN which is over the limit which is less error prone. Adjust the other
users accordingly.
On 32bit PAE kernels on 64bit hardware with enough physical bits,
l1tf_pfn_limit() will overflow unsigned long. This in turn affects
max_swapfile_size() and can lead to swapon returning -EINVAL. This has been
observed in a 32bit guest with 42 bits physical address size, where
max_swapfile_size() overflows exactly to 1 << 32, thus zero, and produces
the following warning to dmesg:
[ 6.396845] Truncating oversized swap area, only using 0k out of 2047996k
Fix this by using unsigned long long instead.
Fixes: 17dbca119312 ("x86/speculation/l1tf: Add sysfs reporting for l1tf") Fixes: 377eeaa8e11f ("x86/speculation/l1tf: Limit swap file size to MAX_PA/2") Reported-by: Dominique Leuenberger <dimstar@suse.de> Reported-by: Adrian Schroeter <adrian@suse.de> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andi Kleen <ak@linux.intel.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180820095835.5298-1-vbabka@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jann reported that x86 was missing required TLB invalidates when he
hit the !*batch slow path in tlb_remove_table().
This is indeed the case; RCU_TABLE_FREE does not provide TLB (cache)
invalidates, the PowerPC-hash where this code originated and the
Sparc-hash where this was subsequently used did not need that. ARM
which later used this put an explicit TLB invalidate in their
__p*_free_tlb() functions, and PowerPC-radix followed that example.
But when we hooked up x86 we failed to consider this. Fix this by
(optionally) hooking tlb_remove_table() into the TLB invalidate code.
NOTE: s390 was also needing something like this and might now
be able to use the generic code again.
[ Modified to be on top of Nick's cleanups, which simplified this patch
now that tlb_flush_mmu_tlbonly() really only flushes the TLB - Linus ]
Fixes: 9e52fc2b50de ("x86/mm: Enable RCU based page table freeing (CONFIG_HAVE_RCU_TABLE_FREE=y)") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Rik van Riel <riel@surriel.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: David Miller <davem@davemloft.net> Cc: Will Deacon <will.deacon@arm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to call this from tlb_flush_mmu_tlbonly, it logically
belongs with tlb_flush_mmu_free. This makes future fixes simpler.
[ This was originally done to allow code consolidation for the
mmu_notifier fix, but it also ends up helping simplify the
HAVE_RCU_TABLE_INVALIDATE fix. - Linus ]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 5d9f40b56630 ("platform/x86: ideapad-laptop: Add
Y520-15IKBN to no_hw_rfkill") added the entry for Y20-15IKBN, and it
turned out that another variant, Y20-15IKBM, also requires the
no_hw_rfkill.
Trim the last letter from the string so that it matches to both
Y20-15IKBN and Y20-15IKBM models.
In many architectures loads may be reordered with older stores to
different locations. In the nvme driver the following two operations
could be reordered:
- Write shadow doorbell (dbbuf_db) into memory.
- Read EventIdx (dbbuf_ei) from memory.
This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell). If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.
This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:
Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).
Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.
Fixes: f9f38e33389c ("nvme: improve performance for virtual NVMe devices") Signed-off-by: Michal Wnukowski <wnukowski@google.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ext4_find_entry() falls back to "searching the old fashioned
way" due to a corrupt dx dir, it needs to reset the error code
to NULL so that the nonstandard ERR_BAD_DX_DIR code isn't returned
to userspace.
While working on extended rand for last_error/first_error timestamps,
I noticed that the endianess is wrong; we access the little-endian
fields in struct ext4_super_block as native-endian when we print them.
This adds a special case in ext4_attr_show() and ext4_attr_store()
to byteswap the superblock fields if needed.
In older kernels, this code was part of super.c, it got moved to
sysfs.c in linux-4.4.
Extended attribute names are defined to be NUL-terminated, so the name
must not contain a NUL character. This is important because there are
places when remove extended attribute, the code uses strlen to
determine the length of the entry. That should probably be fixed at
some point, but code is currently really messy, so the simplest fix
for now is to simply validate that the extended attributes are sane.
When cpu_stop_queue_work() releases the lock for the stopper
thread that was queued into its wake queue, preemption is
enabled, which leads to the following deadlock:
-grabs lock for migration/0-
-spins with preemption disabled,
waiting for migration/0's lock to be
released-
-adds work items for migration/0
and queues migration/0 to its
wake_q-
-releases lock for migration/0
and preemption is enabled-
-current thread is preempted,
and __set_cpus_allowed_ptr
has changed the thread's
cpu allowed mask to CPU1 only-
-acquires migration/0 and migration/1's
locks-
-adds work for migration/0 but does not
add migration/0 to wake_q, since it is
already in a wake_q-
-adds work for migration/1 and adds
migration/1 to its wake_q-
-releases migration/0 and migration/1's
locks, wakes migration/1, and enables
preemption-
-since migration/1 is requested to run,
migration/1 begins to run and waits on
migration/0, but migration/0 will never
be able to run, since the thread that
can wake it is affine to CPU1-
Disable preemption in cpu_stop_queue_work() before queueing works for
stopper threads, and queueing the stopper thread in the wake queue, to
ensure that the operation of queueing the works and waking the stopper
threads is atomic.
Fixes: 0b26351b910f ("stop_machine, sched: Fix migrate_swap() vs. active_balance() deadlock") Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: peterz@infradead.org Cc: matt@codeblueprint.co.uk Cc: bigeasy@linutronix.de Cc: gregkh@linuxfoundation.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1533329766-4856-1-git-send-email-isaacm@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Co-Developed-by: Isaac J. Manjarres <isaacm@codeaurora.org>
The code flow in cpu_stop_queue_two_works() is a little arcane; fix this by
lifting the preempt_disable() to the top to create more natural nesting wrt
the spinlocks and make the wake_up_q() and preempt_enable() unconditional
at the end.
Furthermore, enable preemption in the -EDEADLK case, such that we spin-wait
with preemption enabled.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: isaacm@codeaurora.org Cc: matt@codeblueprint.co.uk Cc: psodagud@codeaurora.org Cc: gregkh@linuxfoundation.org Cc: pkondeti@codeaurora.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180730112140.GH2494@hirez.programming.kicks-ass.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the oom killer kills a userspace process in the page fault handler
while in guest context, the fault handler fails to release the mm_sem
if the FAULT_FLAG_RETRY_NOWAIT option is set. This leads to a deadlock
when tearing down the mm when the process terminates. This bug can only
happen when pfault is enabled, so only KVM clients are affected.
The problem arises in the rare cases in which handle_mm_fault does not
release the mm_sem. This patch fixes the issue by manually releasing
the mm_sem when needed.
When there is contention on faulting in a particular page table entry
at stage 2, the break-before-make requirement of the architecture can
lead to additional refaulting due to TLB invalidation.
Avoid this by skipping a page table update if the new value of the PTE
matches the previous value.
Contention on updating a PMD entry by a large number of vcpus can lead
to duplicate work when handling stage 2 page faults. As the page table
update follows the break-before-make requirement of the architecture,
it can lead to repeated refaults due to clearing the entry and
flushing the tlbs.
This problem is more likely when -
* there are large number of vcpus
* the mapping is large block mapping
such as when using PMD hugepages (512MB) with 64k pages.
Fix this by skipping the page table update if there is no change in
the entry being updated.
ARM64's pfn_valid() shifts away the upper PAGE_SHIFT bits of the input
before seeing if the PFN is valid. This leads to false positives when
some of the upper bits are set, but the lower bits match a valid PFN.
For example, the following userspace code looks up a bogus entry in
/proc/kpageflags:
int pagemap = open("/proc/self/pagemap", O_RDONLY);
int pageflags = open("/proc/kpageflags", O_RDONLY);
uint64_t pfn, val;
On ARM64 this causes the userspace process to crash with SIGSEGV rather
than reading (1 << KPF_NOPAGE). kpageflags_read() treats the offset as
valid, and stable_page_flags() will try to access an address between the
user and kernel address ranges.
The commit 719f6a7040f1bdaf96 ("printk: Use the main logbuf in NMI
when logbuf_lock is available") brought back the possible deadlocks
in printk() and NMI.
The check of logbuf_lock is done only in printk_nmi_enter() to prevent
mixed output. But another CPU might take the lock later, enter NMI, and:
+ Both NMIs might be serialized by yet another lock, for example,
the one in nmi_cpu_backtrace().
+ The other CPU might get stopped in NMI, see smp_send_stop()
in panic().
The only safe solution is to use trylock when storing the message
into the main log-buffer. It might cause reordering when some lines
go to the main lock buffer directly and others are delayed via
the per-CPU buffer. It means that it is not useful in general.
This patch replaces the problematic NMI deferred context with NMI
direct context. It can be used to mark a code that might produce
many messages in NMI and the risk of losing them is more critical
than problems with eventual reordering.
The context is then used when dumping trace buffers on oops. It was
the primary motivation for the original fix. Also the reordering is
even smaller issue there because some traces have their own time stamps.
Finally, nmi_cpu_backtrace() need not longer be serialized because
it will always us the per-CPU buffers again.
Fixes: 719f6a7040f1bdaf96 ("printk: Use the main logbuf in NMI when logbuf_lock is available") Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20180627142028.11259-1-pmladek@suse.com
To: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we check if the number of context banks is not equal to
num_context_interrupts. However, there are booloaders such as, one
on sdm845 that reserves few context banks and thus kernel views
less than the total available context banks.
So, although the hardware definition in device tree would mention
the correct number of context interrupts, this number can be
greater than the number of context banks visible to smmu in kernel.
We should therefore error out only when the number of context banks
is greater than the available number of context interrupts.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Suggested-by: Tomasz Figa <tfiga@chromium.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Will Deacon <will.deacon@arm.com>
[will: drop useless printk] Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If iput() is called on that same inode, evict() will wait for writeback
forever.
btrfs_write_inode() was originally added way back in 4730a4bc5bf3
("btrfs_dirty_inode") to support O_SYNC writes. However, ->write_inode()
hasn't been used for O_SYNC since 148f948ba877 ("vfs: Introduce new
helpers for syncing after writing to O_SYNC file or IS_SYNC inode"), so
btrfs_write_inode() is actually unnecessary (and leads to a bunch of
unnecessary commits). Get rid of it, which also gets rid of the
deadlock.
CC: stable@vger.kernel.org # 3.2+ Signed-off-by: Josef Bacik <jbacik@fb.com>
[Omar: new commit message] Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're trying to make a data reservation and we have to allocate a
data chunk we could leak ret == 1, as do_chunk_alloc() will return 1 if
it allocated a chunk. Since the end of the function is the success path
just return 0.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use customized, nodesize batch value to update dirty_metadata_bytes.
We should also use batch version of compare function or we will easily
goto fast path and get false result from percpu_counter_compare().
Fixes: e2d845211eda ("Btrfs: use percpu counter for dirty metadata count") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Ethan Lien <ethanlien@synology.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fil in the correct namelen (typically 255 not 4096) in the
statfs response and also fill in a reasonably unique fsid
(in this case taken from the volume id, and the creation time
of the volume).
In the case of the POSIX statfs all fields are now filled in,
and in the case of non-POSIX mounts, all fields are filled
in which can be.
Signed-off-by: Steve French <stfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An earlier commit had a typo which prevented the
optimization from working:
commit 18dd8e1a65dd ("Do not send SMB3 SET_INFO request if nothing is changing")
Thank you to Metze for noticing this. Also clear a
reserved field in the FILE_BASIC_INFO struct we send
that should be zero (all the other fields in that
struct were set or cleared explicitly already in
cifs_set_file_info).
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> # 4.9.x+ Reported-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enumerating snapshots, the last few bytes of the final
snapshot could be left off since we were miscalculating the
length returned (leaving off the sizeof struct SRV_SNAPSHOT_ARRAY)
See MS-SMB2 section 2.2.32.2. In addition fixup the length used
to allow smaller buffer to be passed in, in order to allow
returning the size of the whole snapshot array more easily.
Sample userspace output with a kernel patched with this
(mounted to a Windows volume with two snapshots).
Before this patch, the second snapshot would be missing a
few bytes at the end.
~/cifs-2.6# ~/enum-snapshots /mnt/file
press enter to issue the ioctl to retrieve snapshot information ...
size of snapshot array = 102
Num snapshots: 2 Num returned: 2 Array Size: 102
CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kmalloc was not being checked - if it fails issue a warning
and return -ENOMEM to the caller.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: b8da344b74c8 ("cifs: dynamic allocation of ntlmssp blob") Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
cc: Stable <stable@vger.kernel.org>` Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/proc/fs/cifs/DebugData displays the features (Kconfig options)
used to build cifs.ko but it was missing some, and needed comma
separator. These can be useful in debugging certain problems
so we know which optional features were enabled in the user's build.
Also clarify them, by making them more closely match the
corresponding CONFIG_CIFS_* parm.
Old format:
Features: dfs fscache posix spnego xattr acl
New format:
Features: DFS,FSCACHE,SMB_DIRECT,STATS,DEBUG2,ALLOW_INSECURE_LEGACY,CIFS_POSIX,UPCALL(SPNEGO),XATTR,ACL
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Paulo Alcantara <palcantara@suse.de> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MEI enables writes of complete messages only
while read can be performed in parts, hence
write should not update the file offset to
not break interleaving partial reads with writes.
Cc: <stable@vger.kernel.org> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commands that are reset are returned with status
SAM_STAT_COMMAND_TERMINATED. PVSCSI currently returns DID_OK |
SAM_STAT_COMMAND_TERMINATED which fails the command. Instead, set hostbyte
to DID_RESET to allow upper layers to retry.
Tested by copying a large file between two pvscsi disks on same adapter
while performing a bus reset at 1-second intervals. Before fix, commands
sometimes fail with DID_OK. After fix, commands observed to fail with
DID_RESET.
Signed-off-by: Jim Gill <jgill@vmware.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving a LOGO request we forget to clear the FC_RP_STARTED flag
before starting the rport delete routine.
As the started flag was not cleared, we're not deleting the rport but
waiting for a restart and thus are keeping the reference count of the rdata
object at 1.
KASAN reports a use-after-free in fcoe_ctlr_els_send() when we're sending a
LOGO and have FIP debugging enabled. This is because we're first freeing
the skb and then printing the frame's DID. But the DID is a member of the
FC frame header which in turn is the skb's payload.
Exchange the debug print and kfree_skb() calls so we're not touching the
freed data.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems using edge triggered ACPI Event Interrupts, the initial
state at boot is not setup by the firmware, instead relying on the edge
irq event handler running at least once to setup the initial state.
2 known examples of this are:
1) The Surface 3 has its _LID state controlled by an ACPI operation region
triggered by a GPIO event:
Method (_E4C, 0, Serialized) // _Exx: Edge-Triggered GPE
{
If ((HELD == One))
{
^^LID.LIDB = One
}
Else
{
^^LID.LIDB = Zero
Notify (LID, 0x80) // Status Change
}
Notify (^^PCI0.SPI1.NTRG, One) // Device Check
}
Currently, the state of LIDB is wrong until the user actually closes or
open the cover. We need to trigger the GPIO event once to update the
internal ACPI state.
Coincidentally, this also enables the Surface 2 integrated HID sensor hub
which also requires an ACPI gpio operation region to start initialization.
2) Various Bay Trail based tablets come with an external USB mux and
TI T1210B USB phy to enable USB gadget mode. The mux is controlled by a
GPIO which is controlled by an edge triggered ACPI Event Interrupt which
monitors the micro-USB ID pin.
When the tablet is connected to a PC (or no cable is plugged in), the ID
pin is high and the tablet should be in gadget mode. But the GPIO
controlling the mux is initialized by the firmware so that the USB data
lines are muxed to the host controller.
This means that if the user wants to use gadget mode, the user needs to
first plug in a host-cable to force the ID pin low and then unplug it
and connect the tablet to a PC, to get the ACPI event handler to run and
switch the mux to device mode,
This commit fixes both by running the event-handler once on boot.
Note that the running of the event-handler is done from a late_initcall,
this is done because the handler AML code may rely on OperationRegions
registered by other builtin drivers. This avoids errors like these:
[ 0.133026] ACPI Error: No handler for Region [XSCG] ((____ptrval____)) [GenericSerialBus] (20180531/evregion-132)
[ 0.133036] ACPI Error: Region GenericSerialBus (ID=9) has no handler (20180531/exfldio-265)
[ 0.133046] ACPI Error: Method parse/execution failed \_SB.GPO2._E12, AE_NOT_EXIST (20180531/psparse-516)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
[hdegoede: Document BYT USB mux reliance on initial trigger]
[hdegoede: Run event handler from a late_initcall, rather then immediately] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of memcg_online_kmem() failure, memcg_cgroup::id remains hashed
in mem_cgroup_idr even after memcg memory is freed. This leads to leak
of ID in mem_cgroup_idr.
This patch adds removal into mem_cgroup_css_alloc(), which fixes the
problem. For better readability, it adds a generic helper which is used
in mem_cgroup_alloc() and mem_cgroup_id_put_many() as well.
Link: http://lkml.kernel.org/r/152354470916.22460.14397070748001974638.stgit@localhost.localdomain
Fixes 73f576c04b94 ("mm: memcontrol: fix cgroup creation failure after many small jobs") Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current value for a target abort error is 0x010, however, this value
should in fact be 0x002. As it stands, the range of error is 0..7 so
it is currently never being detected. This bug has been in the driver
since the early 2.6.12 days (or before).
Detected by CoverityScan, CID#744290 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously in squashfs_readpage() when copying data into the page
cache, it used the length of the datablock read from the filesystem
(after decompression). However, if the filesystem has been corrupted
this data block may be short, which will leave pages unfilled.
The fix for this is to compute the expected number of bytes to copy
from the inode size, and use this to detect if the block is short.
Delete the old VM_BUG_ON_VMA() from zap_pmd_range(), which asserted
that mmap_sem must be held when splitting an "anonymous" vma there.
Whether that's still strictly true nowadays is not entirely clear,
but the danger of sometimes crashing on the BUG is now fairly clear.
Even with the new stricter rules for anonymous vma marking, the
condition it checks for can possible trigger. Commit 44960f2a7b63
("staging: ashmem: Fix SIGBUS crash when traversing mmaped ashmem
pages") is good, and originally I thought it was safe from that
VM_BUG_ON_VMA(), because the /dev/ashmem fd exposed to the user is
disconnected from the vm_file in the vma, and madvise(,,MADV_REMOVE)
insists on VM_SHARED.
But after I read John's earlier mail, drawing attention to the
vfs_fallocate() in there: I may be wrong, and I don't know if Android
has THP in the config anyway, but it looks to me like an
unmap_mapping_range() from ashmem's vfs_fallocate() could hit precisely
the VM_BUG_ON_VMA(), once it's vma_is_anonymous().
Anatoly continues to find issues with fuzzed squashfs images.
This time, corrupt, missing, or undersized data for the page filling
wasn't checked for, because the squashfs_{copy,read}_cache() functions
did the squashfs_copy_data() call without checking the resulting data
size.
Which could result in the page cache pages being incompletely filled in,
and no error indication to the user space reading garbage data.
So make a helper function for the "fill in pages" case, because the
exact same incomplete sequence existed in two places.
[ I should have made a squashfs branch for these things, but I didn't
intend to start doing them in the first place.
My historical connection through cramfs is why I got into looking at
these issues at all, and every time I (continue to) think it's a
one-off.
Because _this_ time is always the last time. Right? - Linus ]
In commit ab123fe071c9 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071c9 ("enic: handle mtu change for vf properly") Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is necessary to be able to include <linux/msi.h> when
CONFIG_GENERIC_MSI_IRQ_DOMAIN is enabled. Without this, a build with
CONFIG_GENERIC_MSI_IRQ_DOMAIN fails with:
In file included from drivers//ata/ahci.c:45:0:
>> include/linux/msi.h:226:10: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:230:9: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:239:12: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:240:22: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*msi_finish)(msi_alloc_info_t *arg, int retval);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:241:20: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*set_desc)(msi_alloc_info_t *arg,
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:316:18: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:318:29: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int virq, int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code that was added to force gcc not to inline any function that isn't
explicitly declared as inline uncovered that init_tick_ops() isn't
marked as "__init". It is only called by __init functions and more
importantly it too calls an __init function which would require it to be
__init as well.
Link: http://lkml.kernel.org/r/201806060444.hdHcKOBy%fengguang.wu@intel.com Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
../arch/arc/mm/cache.c: In function 'flush_anon_page':
../arch/arc/mm/cache.c:1062:55: warning: passing argument 2 of '__flush_dcache_page' makes integer from pointer without a cast [-Wint-conversion]
__flush_dcache_page((phys_addr_t)page_address(page), page_address(page));
^~~~~~~~~~~~~~~~~~
../arch/arc/mm/cache.c:1013:59: note: expected 'long unsigned int' but argument is of type 'void *'
void __flush_dcache_page(phys_addr_t paddr, unsigned long vaddr)
~~~~~~~~~~~~~~^~~~~
Fix build errors in arch/arc/'s delay.h:
- add "extern unsigned long loops_per_jiffy;"
- add <asm-generic/types.h> for "u64"
In file included from ../drivers/infiniband/hw/cxgb3/cxio_hal.c:32:
../arch/arc/include/asm/delay.h: In function '__udelay':
../arch/arc/include/asm/delay.h:61:12: error: 'u64' undeclared (first use in this function)
loops = ((u64) usecs * 4295 * HZ * loops_per_jiffy) >> 32;
^~~
In file included from ../drivers/infiniband/hw/cxgb3/cxio_hal.c:32:
../arch/arc/include/asm/delay.h: In function '__udelay':
../arch/arc/include/asm/delay.h:63:37: error: 'loops_per_jiffy' undeclared (first use in this function)
loops = ((u64) usecs * 4295 * HZ * loops_per_jiffy) >> 32;
^~~~~~~~~~~~~~~
Fix printk format warning in arch/arc/plat-eznps/mtm.c:
In file included from ../include/linux/printk.h:7,
from ../include/linux/kernel.h:14,
from ../include/linux/list.h:9,
from ../include/linux/smp.h:12,
from ../arch/arc/plat-eznps/mtm.c:17:
../arch/arc/plat-eznps/mtm.c: In function 'set_mtm_hs_ctr':
../include/linux/kern_levels.h:5:18: warning: format '%d' expects argument of type 'int', but argument 2 has type 'long int' [-Wformat=]
#define KERN_SOH "\001" /* ASCII Start Of Header */
^~~~~~
../include/linux/kern_levels.h:11:18: note: in expansion of macro 'KERN_SOH'
#define KERN_ERR KERN_SOH "3" /* error conditions */
^~~~~~~~
../include/linux/printk.h:308:9: note: in expansion of macro 'KERN_ERR'
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~
../arch/arc/plat-eznps/mtm.c:166:3: note: in expansion of macro 'pr_err'
pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
^~~~~~
../arch/arc/plat-eznps/mtm.c:166:40: note: format string is defined here
pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
~^
%ld
The hs_ctr variable can just be int instead of long, so also change
kstrtol() to kstrtoint() and leave the format string as %d.
Also add 2 header files since they are used in mtm.c and we prefer
not to depend on accidental/indirect #includes.
Cc: linux-snps-arc@lists.infradead.org Cc: Ofer Levi <oferle@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add <linux/types.h> to fix build errors.
Both ctop.h and <soc/nps/common.h> use u32 types and cause many
errors.
Examples:
../include/soc/nps/common.h:71:4: error: unknown type name 'u32'
u32 __reserved:20, cluster:4, core:4, thread:4;
../include/soc/nps/common.h:76:3: error: unknown type name 'u32'
u32 value;
../include/soc/nps/common.h:124:4: error: unknown type name 'u32'
u32 base:8, cl_x:4, cl_y:4,
../include/soc/nps/common.h:127:3: error: unknown type name 'u32'
u32 value;
../arch/arc/plat-eznps/include/plat/ctop.h:83:4: error: unknown type name 'u32'
u32 gen:1, gdis:1, clk_gate_dis:1, asb:1,
../arch/arc/plat-eznps/include/plat/ctop.h:86:3: error: unknown type name 'u32'
u32 value;
../arch/arc/plat-eznps/include/plat/ctop.h:93:4: error: unknown type name 'u32'
u32 csa:22, dmsid:6, __reserved:3, cs:1;
../arch/arc/plat-eznps/include/plat/ctop.h:95:3: error: unknown type name 'u32'
u32 value;
Cc: linux-snps-arc@lists.infradead.org Cc: Ofer Levi <oferle@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function nfp_flower_repr_get_type_and_port expects an enum nfp_repr_type
return value but, if the repr type is unknown, returns a value of type
enum nfp_flower_cmsg_port_type. This means that if FW encodes the port
ID in a way the driver does not understand instead of dropping the frame
driver may attribute it to a physical port (uplink) provided the port
number is less than physical port count.
Fix this and ensure a net_device of NULL is returned if the repr can not
be determined.
Fixes: 1025351a88a4 ("nfp: add flower app") Signed-off-by: John Hurley <john.hurley@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As for today we don't setup SMP_CACHE_BYTES and cache_line_size for
ARC, so they are set to L1_CACHE_BYTES by default. L1 line length
(L1_CACHE_BYTES) might be easily smaller than L2 line (which is
usually the case BTW). This breaks code.
For example this breaks ethernet infrastructure on HSDK/AXS103 boards
with IOC disabled, involving manual cache flushes
Functions which alloc and manage sk_buff packet data area rely on
SMP_CACHE_BYTES define. In the result we can share last L2 cache
line in sk_buff linear packet data area between DMA buffer and
some useful data in other structure. So we can lose this data when
we invalidate DMA buffer.
sk_buff linear packet data area
|
|
| skb->end skb->tail
V | |
V V
----------------------------------------------.
packet data | <tail padding> | <useful data in other struct>
----------------------------------------------.
---------------------.--------------------------------------------------.
SLC line | SLC (L2 cache) line (128B) |
---------------------.--------------------------------------------------.
^ ^
| |
These cache lines will be invalidated when we invalidate skb
linear packet data area before DMA transaction starting.
This leads to issues painful to debug as it reproduces only if
(sk_buff->end - sk_buff->tail) < SLC_LINE_SIZE and
if we have some useful data right after sk_buff->end.
Fix that by hardcode SMP_CACHE_BYTES to max line length we may have.
This reverts commit 2a027b47dba6 ("MIPS: BCM47XX: Enable 74K Core
ExternalSync for PCIe erratum").
Enabling ExternalSync caused a regression for BCM4718A1 (used e.g. in
Netgear E3000 and ASUS RT-N16): it simply hangs during PCIe
initialization. It's likely that BCM4717A1 is also affected.
I didn't notice that earlier as the only BCM47XX devices with PCIe I
own are:
1) BCM4706 with 2 x 14e4:4331
2) BCM4706 with 14e4:4360 and 14e4:4331
it appears that BCM4706 is unaffected.
While BCM5300X-ES300-RDS.pdf seems to document that erratum and its
workarounds (according to quotes provided by Tokunori) it seems not even
Broadcom follows them.
According to the provided info Broadcom should define CONF7_ES in their
SDK's mipsinc.h and implement workaround in the si_mips_init(). Checking
both didn't reveal such code. It *could* mean Broadcom also had some
problems with the given workaround.
This fixes the reported family on modern AMD processors (e.g. Ryzen,
which is family 0x17). Previously these processors all showed up as
family 0xf.
See the document
https://support.amd.com/TechDocs/56255_OSRR.pdf
section CPUID_Fn00000001_EAX for how to calculate the family
from the BaseFamily and ExtFamily values.
This matches the code in arch/x86/lib/cpu.c
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/sys/../zswap/stored_pages keeps rising in a zswap test with
"zswap.max_pool_percent=0" parameter. But it should not compress or
store pages any more since there is no space in the compressed pool.
Reproduce steps:
1. Boot kernel with "zswap.enabled=1"
2. Set the max_pool_percent to 0
# echo 0 > /sys/module/zswap/parameters/max_pool_percent
3. Do memory stress test to see if some pages have been compressed
# stress --vm 1 --vm-bytes $mem_available"M" --timeout 60s
4. Watching the 'stored_pages' number increasing or not
The root cause is:
When zswap_max_pool_percent is set to 0 via kernel parameter,
zswap_is_full() will always return true due to zswap_shrink(). But if
the shinking is able to reclain a page successfully the code then
proceeds to compressing/storing another page, so the value of
stored_pages will keep changing.
To solve the issue, this patch adds a zswap_is_full() check again after
zswap_shrink() to make sure it's now under the max_pool_percent, and to
not compress/store if we reached the limit.
Link: http://lkml.kernel.org/r/20180530103936.17812-1-liwang@redhat.com Signed-off-by: Li Wang <liwang@redhat.com> Acked-by: Dan Streetman <ddstreet@ieee.org> Cc: Seth Jennings <sjenning@redhat.com> Cc: Huang Ying <huang.ying.caritas@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for load/store tearing prevention to work, _all_ accesses to
the variable in question need to be done around READ and WRITE_ONCE()
macros. Ensure everyone does so for q->status variable for
semtimedop().
Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.
Signed-off-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we meet a conflicting object that is marked FSCACHE_OBJECT_IS_LIVE in
the active object tree, we have been emitting a BUG after logging
information about it and the new object.
Instead, we should wait for the CACHEFILES_OBJECT_ACTIVE flag to be cleared
on the old object (or return an error). The ACTIVE flag should be cleared
after it has been removed from the active object tree. A timeout of 60s is
used in the wait, so we shouldn't be able to get stuck there.
Fixes: 9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem") Signed-off-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cachefiles_read_waiter() has the right to access a 'monitor' object by
virtue of being called under the waitqueue lock for one of the pages in its
purview. However, it has no ref on that monitor object or on the
associated operation.
What it is allowed to do is to move the monitor object to the operation's
to_do list, but once it drops the work_lock, it's actually no longer
permitted to access that object. However, it is trying to enqueue the
retrieval operation for processing - but it can only do this via a pointer
in the monitor object, something it shouldn't be doing.
If it doesn't enqueue the operation, the operation may not get processed.
If the order is flipped so that the enqueue is first, then it's possible
for the work processor to look at the to_do list before the monitor is
enqueued upon it.
Fix this by getting a ref on the operation so that we can trust that it
will still be there once we've added the monitor to the to_do list and
dropped the work_lock. The op can then be enqueued after the lock is
dropped.
The bug can manifest in one of a couple of ways. The first manifestation
looks like:
FS-Cache:
FS-Cache: Assertion failed
FS-Cache: 6 == 5 is false
------------[ cut here ]------------
kernel BUG at fs/fscache/operation.c:494!
RIP: 0010:fscache_put_operation+0x1e3/0x1f0
...
fscache_op_work_func+0x26/0x50
process_one_work+0x131/0x290
worker_thread+0x45/0x360
kthread+0xf8/0x130
? create_worker+0x190/0x190
? kthread_cancel_work_sync+0x10/0x10
ret_from_fork+0x1f/0x30
This is due to the operation being in the DEAD state (6) rather than
INITIALISED, COMPLETE or CANCELLED (5) because it's already passed through
fscache_put_operation().
Dirk Gouders reported that two consecutive "make" invocations on an
already compiled tree will show alternating behaviors:
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
DATAREL arch/x86/boot/compressed/vmlinux
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
LD arch/x86/boot/compressed/vmlinux
ZOFFSET arch/x86/boot/zoffset.h
AS arch/x86/boot/header.o
LD arch/x86/boot/setup.elf
OBJCOPY arch/x86/boot/setup.bin
OBJCOPY arch/x86/boot/vmlinux.bin
BUILD arch/x86/boot/bzImage
Setup is 15644 bytes (padded to 15872 bytes).
System is 6663 kB
CRC 3eb90f40
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
He bisected it back to:
commit 98f78525371b ("x86/boot: Refuse to build with data relocations")
The root cause was the use of the "if_changed" kbuild function multiple
times for the same target. It was designed to only be used once per
target, otherwise it will effectively always trigger, flipping back and
forth between the two commands getting recorded by "if_changed". Instead,
this patch merges the two commands into a single function to get stable
build artifacts (i.e. .vmlinux.cmd), and a single build behavior.
NO_RT_RUNTIME_SHARE feature is used to prevent a CPU borrow enough
runtime with a spin-rt-task.
However, if RT_RUNTIME_SHARE feature is enabled and rt_rq has borrowd
enough rt_runtime at the beginning, rt_runtime can't be restored to
its initial bandwidth rt_runtime after we disable RT_RUNTIME_SHARE.
E.g. on my PC with 4 cores, procedure to reproduce:
1) Make sure RT_RUNTIME_SHARE is enabled
cat /sys/kernel/debug/sched_features
GENTLE_FAIR_SLEEPERS START_DEBIT NO_NEXT_BUDDY LAST_BUDDY
CACHE_HOT_BUDDY WAKEUP_PREEMPTION NO_HRTICK NO_DOUBLE_TICK
LB_BIAS NONTASK_CAPACITY TTWU_QUEUE NO_SIS_AVG_CPU SIS_PROP
NO_WARN_DOUBLE_CLOCK RT_PUSH_IPI RT_RUNTIME_SHARE NO_LB_MIN
ATTACH_AGE_LOAD WA_IDLE WA_WEIGHT WA_BIAS
2) Start a spin-rt-task
./loop_rr &
3) set affinity to the last cpu
taskset -p 8 $pid_of_loop_rr
4) Observe that last cpu have borrowed enough runtime.
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
5) Disable RT_RUNTIME_SHARE
echo NO_RT_RUNTIME_SHARE > /sys/kernel/debug/sched_features
6) Observe that rt_runtime can not been restored
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
This patch help to restore rt_runtime after we disable
RT_RUNTIME_SHARE.
The original mapping for the DW5821e was done using a development
version of the firmware. Confirmed with the vendor that the final
USB layout ends up exposing the QMI control/data ports in USB
config #1, interface #0, not in interface #1 (which is now a HID
interface).
Fixes: e7e197edd09c25 ("qmi_wwan: add support for the Dell Wireless 5821e module") Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).
The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.
The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:
In file included from arch/sparc/include/asm/page.h:10:0,
...
from drivers/staging/media/omap4iss/iss_video.c:15:
include/linux/highmem.h: In function 'clear_user_highpage':
include/linux/highmem.h:137:31: error:
passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
pointer type
Include generic includes files first to fix the problem.
Fixes: fc96d58c10162 ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.
Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().
Compile tested only; I lack hardware.
Fixes: 7b7017642199 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring") Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not expose the address of vmx->nested.current_vmptr to
kvm_write_guest_virt_system() as the resulting __copy_to_user()
call will trigger a WARN when CONFIG_HARDENED_USERCOPY is
enabled.
Opportunistically clean up variable names in handle_vmptrst()
to improve readability, e.g. vmcs_gva is misleading as the
memory operand of VMPTRST is plain memory, not a VMCS.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Tested-by: Peter Shier <pshier@google.com> Reviewed-by: Peter Shier <pshier@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its possible to rename two chains to the same name in one
transaction:
nft add chain t c1
nft add chain t c2
nft 'rename chain t c1 c3;rename chain t c2 c3'
This creates two chains named 'c3'.
Appears to be harmless, both chains can still be deleted both
by name or handle, but, nevertheless, its a bug.
Walk transaction log and also compare vs. the pending renames.
Both chains can still be deleted, but nevertheless it is a bug as
we don't allow to create chains with identical names, so we should
prevent this from happening-by-rename too.
The new name is stored in the transaction metadata, on commit,
the pointers to the old and new names are swapped.
Therefore in abort and commit case we have to free the
pointer in the chain_trans container.
In commit case, the pointer can be used by another cpu that
is currently dumping the renamed chain, thus kfree needs to
happen after waiting for rcu readers to complete.
Fixes: b7263e071a ("netfilter: nf_tables: Allow chain name of up to 255 chars") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of the JITs is allowed to implement exit paths from the BPF
insn mappings other than BPF_JMP | BPF_EXIT. In the BPF core code
we have a couple of rewrites in eBPF (e.g. LD_ABS / LD_IND) and
in eBPF to cBPF translation to retain old existing behavior where
exceptions may occur; they are also tightly controlled by the
verifier where it disallows some of the features such as BPF to
BPF calls when legacy LD_ABS / LD_IND ops are present in the BPF
program. During recent review of all BPF_XADD JIT implementations
I noticed that the ppc64 one is buggy in that it contains two
jumps to exit paths. This is problematic as this can bypass verifier
expectations e.g. pointed out in commit f6b1b3bf0d5f ("bpf: fix
subprog verifier bypass by div/mod by 0 exception"). The first
exit path is obsoleted by the fix in ca36960211eb ("bpf: allow xadd
only on aligned memory") anyway, and for the second one we need to
do a fetch, add and store loop if the reservation from lwarx/ldarx
was lost in the meantime.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Reviewed-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Tested-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GC of set uses call_rcu() to destroy elements.
So that elements would be destroyed after destroying sets and chains.
But, elements should be destroyed before destroying sets and chains.
In order to wait calling call_rcu(), a rcu_barrier() is added.
In order to test correctly, below patch should be applied.
https://patchwork.ozlabs.org/patch/940883/
The list [1] of commits doing endianness fixes in USB subsystem is long
due to below quote from USB spec Revision 2.0 from April 27, 2000:
------------
8.1 Byte/Bit Ordering
Multiple byte fields in standard descriptors, requests, and responses
are interpreted as and moved over the bus in little-endian order, i.e.
LSB to MSB.
------------
This commit belongs to the same family.
[1] Example of endianness fixes in USB subsystem:
commit 14e1d56cbea6 ("usb: gadget: f_uac2: endianness fixes.")
commit 42370b821168 ("usb: gadget: f_uac1: endianness fixes.")
commit 63afd5cc7877 ("USB: chaoskey: fix Alea quirk on big-endian hosts")
commit 74098c4ac782 ("usb: gadget: acm: fix endianness in notifications")
commit cdd7928df0d2 ("ACM gadget: fix endianness in notifications")
commit 323ece54e076 ("cdc-wdm: fix endianness bug in debug statements")
commit e102609f1072 ("usb: gadget: uvc: Fix endianness mismatches")
list goes on
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tools/usb/ffs-test.c file defines cpu_to_le16/32 by using the C
library htole16/32 function calls. However, cpu_to_le16/32 are used when
initializing structures, i.e in a context where a function call is not
allowed.
It works fine on little endian systems because htole16/32 are defined by
the C library as no-ops. But on big-endian systems, they are actually
doing something, which might involve calling a function, causing build
failures, such as:
ffs-test.c:48:25: error: initializer element is not constant
#define cpu_to_le32(x) htole32(x)
^~~~~~~
ffs-test.c:128:12: note: in expansion of macro ‘cpu_to_le32’
.magic = cpu_to_le32(FUNCTIONFS_DESCRIPTORS_MAGIC_V2),
^~~~~~~~~~~
To solve this, we code cpu_to_le16/32 in a way that allows them to be
used when initializing structures. This fix was imported from
meta-openembedded/android-tools/fix-big-endian-build.patch written by
Thomas Petazzoni <thomas.petazzoni@free-electrons.com>.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
The change protects almost the whole body of u_audio_iso_complete()
function by PCM stream lock, this is mainly sufficient to avoid a race
between USB request completion and stream termination, the change
prevents a possibility of invalid memory access in interrupt context
by memcpy():
Also added a check for potential !runtime condition, commonly it is
done by PCM_RUNTIME_CHECK(substream) in the beginning, however this
does not completely prevent from oopses in u_audio_iso_complete(),
because the proper protection scheme must be implemented in PCM
library functions.
An example of *not fixed* oops due to substream->runtime->*
dereference by snd_pcm_running(substream) from
snd_pcm_period_elapsed(), where substream->runtime is gone while
waiting the substream lock:
Unable to handle kernel paging request at virtual address 6b6b6b6b
pgd = db7e4000
[6b6b6b6b] *pgd=00000000
CPU: 0 PID: 193 Comm: klogd Tainted: G C 3.14.54+ #118
task: db5ac500 ti: db60c000 task.ti: db60c000
PC is at snd_pcm_period_elapsed+0x48/0xd8 [snd_pcm]
LR is at snd_pcm_period_elapsed+0x40/0xd8 [snd_pcm]
pc : [<>] lr : [<>] psr: 60000193
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2b7e404a DAC: 00000015
Process klogd (pid: 193, stack limit = 0xdb60c238)
[<>] (snd_pcm_period_elapsed [snd_pcm]) from [<>] (udc_irq+0x500/0xbbc)
[<>] (udc_irq) from [<>] (ci_irq+0x280/0x304)
[<>] (ci_irq) from [<>] (handle_irq_event_percpu+0xa4/0x40c)
[<>] (handle_irq_event_percpu) from [<>] (handle_irq_event+0x3c/0x5c)
[<>] (handle_irq_event) from [<>] (handle_fasteoi_irq+0xc4/0x110)
[<>] (handle_fasteoi_irq) from [<>] (generic_handle_irq+0x20/0x30)
[<>] (generic_handle_irq) from [<>] (handle_IRQ+0x80/0xc0)
[<>] (handle_IRQ) from [<>] (gic_handle_irq+0x3c/0x60)
[<>] (gic_handle_irq) from [<>] (__irq_svc+0x44/0x78)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
[erosca: W/o this patch, with minimal instrumentation [1], I can
consistently reproduce BUG: KASAN: use-after-free [2]]
[1] Instrumentation to reproduce issue [2]:
# diff --git a/drivers/usb/gadget/function/u_audio.c b/drivers/usb/gadget/function/u_audio.c
# index a72295c953bb..bd0b308024fe 100644
# --- a/drivers/usb/gadget/function/u_audio.c
# +++ b/drivers/usb/gadget/function/u_audio.c
# @@ -16,6 +16,7 @@
# #include <sound/core.h>
# #include <sound/pcm.h>
# #include <sound/pcm_params.h>
# +#include <linux/delay.h>
#
# #include "u_audio.h"
#
# @@ -147,6 +148,8 @@ static void u_audio_iso_complete(struct usb_ep *ep, struct usb_request *req)
#
# spin_unlock_irqrestore(&prm->lock, flags);
#
# + udelay(500); //delay here to increase probability of parallel activities
# +
# /* Pack USB load in ALSA ring buffer */
# pending = prm->dma_bytes - hw_ptr;
[2] After applying [1], below BUG occurs on Rcar-H3-Salvator-X board:
==================================================================
BUG: KASAN: use-after-free in u_audio_iso_complete+0x24c/0x520 [u_audio]
Read of size 8 at addr ffff8006cafcc248 by task swapper/0/0
Substream period size potentially can be changed in runtime, however
this is not accounted in the data copying routine, the change replaces
the cached value with an actual value from substream runtime.
As a side effect the change also removes a potential division by zero
in u_audio_iso_complete() function, if there is a race with
uac_pcm_hw_free(), which sets prm->period_size to 0.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no necessity to copy PCM stream ring buffer area and size
properties to UAC private data structure, these values can be got
from substream itself.
The change gives more control on substream and avoid stale caching.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log