Gaosheng Cui [Tue, 13 Sep 2022 02:48:46 +0000 (10:48 +0800)]
drm/amd/pm: remove unused declarations in hardwaremanager.h
phm_is_hw_access_blocked() and phm_block_hw_access() has been
removed since commit 698f88e697cc ("drm/amd/powerplay: delete
dead code in powerplay"), so remove them.
Gaosheng Cui [Tue, 13 Sep 2022 02:48:45 +0000 (10:48 +0800)]
drm/gma500: remove unused declarations in psb_intel_drv.h
psb_intel_sdvo_supports_hotplug(), psb_intel_sdvo_set_hotplug()
and psb_intel_sdvo_find() have been removed since
commit 871c60156dbe ("drm/gma500: Remove dead code"),
so remove them.
Maxime Ripard [Mon, 29 Aug 2022 13:47:30 +0000 (15:47 +0200)]
drm/vc4: hdmi: Reset link on hotplug
During a hotplug cycle (such as a TV going out of suspend, or when the
cable is disconnected and reconnected), the expectation is that the same
state used before the disconnection is reused until the next commit.
However, the HDMI scrambling requires that some flags are set in the
monitor, and those flags are very likely to be reset when the cable has
been disconnected. This will thus result in a blank display, even if the
display pipeline configuration hasn't been modified or is in the exact
same state.
The solution we've had so far is to enable the scrambling-related bits
again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 -
Scrambling Control) requires that the scrambling enable bit is set
before sending any scrambled video signal. Using that solution thus
breaks that expectation.
The solution used by i915 is to do a full modeset on the connector so
that we disable the video signal, enable the scrambling bit, and enable
the video signal again.
As such, we took that code and plugged it into vc4. It probably could
have been turned into an helper, but it proved to be difficult for
several reasons:
* i915 has fairly different structures than simpler KMS drivers such
as vc4, so doing some code that works with both proved to be
difficult;
* Other simpler drivers could reuse some of it (tegra, dw-hdmi), but
it would still require to move some parameters currently stored in
private structure that are needed to compute whether the scrambling
is needed or not, and then inform the driver that it needs to be
enabled. Some of those parameters are already in core structures
(drm_display_mode, drm_display_info, bpc), but the output format
isnt't. Adding it is fairly challenging since unlike the TMDS char
rate or mode, there's no consensus on what format to pick in
drivers, so it's not possible to write some generic code that can
depend on it.
For these reasons, we chose to duplicate the code for now, until someone
else really needs it as well, in which case we will be able to convert
it into a generic helper.
Maxime Ripard [Mon, 29 Aug 2022 13:47:27 +0000 (15:47 +0200)]
drm/vc4: hdmi: Simplify the hotplug handling
Our detect callback has a bunch of operations to perform depending on
the current and last status of the connector, such a setting the CEC
physical address or enabling the scrambling again.
This is currently dealt with a bunch of if / else statetements that make
it fairly difficult to read and extend.
Let's move all that logic to a function of its own.
Maxime Ripard [Mon, 29 Aug 2022 13:47:26 +0000 (15:47 +0200)]
drm/vc4: hdmi: Remove mutex in detect
We recently introduced a new mutex to protect concurrent execution of
ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi
fields.
However, using it in the detect hook was creating a reentrency issue
with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect
might call the CEC adap_enable hook with the lock held, eventually
resulting in a deadlock.
Since we didn't really need to protect anything at the moment in the CEC
code, the decision was made to ignore the mutex in those CEC hooks,
working around the issue.
However, we can have the same thing happening if we end up triggering a
mode set from the detect callback, for example using
drm_atomic_helper_connector_hdmi_reset_link().
Since we don't really need to protect anything in detect either, let's
just drop the lock in detect, and add it again in CEC.
Jouni Högander [Tue, 23 Aug 2022 11:29:20 +0000 (14:29 +0300)]
drm/tests: Set also mock plane src_x, src_y, src_w and src_h
We need to set also src_x, src_y, src_w and src_h for the mock plane.
After fix for drm_atomic_helper_damage_iter_init we are using these
when iterating damage_clips.
Jouni Högander [Tue, 23 Aug 2022 11:29:17 +0000 (14:29 +0300)]
drm: Use original src rect while initializing damage iterator
drm_plane_state->src might be modified by the driver. This is done
e.g. in i915 driver when there is bigger framebuffer than the plane
and there is some offset within framebuffer. I915 driver calculates
separate offset and adjusts src rect coords to be relative to this
offset. Damage clips are still relative to original src coords
provided by user-space.
This patch ensures original coordinates provided by user-space are
used when initiliazing damage iterator.
Robert Foss [Mon, 12 Sep 2022 11:38:59 +0000 (13:38 +0200)]
Revert "drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP"
As reported by Laurent in response to this commit[1], this functionality
should not be implemented using the devicetree, because of this let's
revert this series for now.
Robert Foss [Mon, 12 Sep 2022 11:38:57 +0000 (13:38 +0200)]
Revert "dt-bindings: Add byteswap order to chrontel ch7033"
As reported by Laurent in response to this commit[1], this functionality
should not be implemented using the devicetree, because of this let's
revert this series for now.
Hamza Mahfooz [Sat, 10 Sep 2022 22:48:16 +0000 (18:48 -0400)]
drm/bridge: it6505: use drm_debug_enabled() in it6505_debug_print()
As made mention of in commit 9f0ac028410f ("drm/print: rename drm_debug
to __drm_debug to discourage use"), we shouldn't explicitly refer to
__drm_debug in this context. So, use drm_debug_enabled() instead.
Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver") Signed-off-by: Hamza Mahfooz <someguy@effective-light.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220910224816.15058-1-someguy@effective-light.com
Add drm_fb_build_fourcc_list() function that builds a list of supported
formats from native and emulated ones. Helpful for all drivers that do
format conversion as part of their plane updates. Update current caller.
v3:
* improve warnings on ignored formats (Sam)
v2:
* use u32 instead of uint32_t (Sam)
* print a warning if output array is too small (Sam)
* comment fixes (Sam)
Thomas Zimmermann [Mon, 5 Sep 2022 14:16:47 +0000 (16:16 +0200)]
drm/modes: Add initializer macro DRM_MODE_INIT()
The macro DRM_MODE_INIT() initializes an instance of
struct drm_display_mode with typical parameters. Convert simpledrm
and also update the macro DRM_SIMPLE_MODE().
v3:
* fix DRM_MODE_INIT() docs (kernel test robot)
Add drm_crtc_helper_mode_valid_fixed(), which validates a given mode
against a display hardware's mode. Convert simpledrm and use it in a
few other drivers with static modes.
v4:
* remove empty line after opening brace
v2:
* rename 'static' and 'hw' to 'fixed' everywhere
It's better to perform the sync at the very last of the suspend
instead of the pipe-disable function, so that we can catch all pending
URBs (if any).
While we're at it, drop the error code from udl_sync_pending_urb()
since we basically ignore it; instead, give a clear error message
indicating a problem.
drm/udl: Don't re-initialize stuff at retrying the URB list allocation
udl_alloc_urb_list() retires the allocation if there is no enough room
left, and it reinitializes the stuff unnecessarily such as the linked
list head and the waitqueue, which could be harmful. Those should be
outside the retry loop.
drm/udl: Fix inconsistent urbs.count value during udl_free_urb_list()
In the current design, udl_get_urb() may be called asynchronously
during the driver freeing its URL list via udl_free_urb_list().
The problem is that the sync is determined by comparing the urbs.count
and urbs.available fields, while we clear urbs.count field only once
after udl_free_urb_list() finishes, i.e. during udl_free_urb_list(),
the state becomes inconsistent.
For fixing this inconsistency and also for hardening the locking
scheme, this patch does a slight refactoring of the code around
udl_get_urb() and udl_free_urb_list(). Now urbs.count is updated in
the same spinlock at extracting a URB from the list in
udl_free_url_list().
The alignment of damaged area was needed for the original udlfb driver
that tried to trim the superfluous copies between front and backend
buffers and handle data in long int. It's not the case for udl DRM
driver, hence we can omit the whole unneeded alignment, as well as the
dead code.
It seems that the current size (4) for the URB list is too small on
some devices, and it resulted in the occasional stalls. Increase the
default URB list size to 20 for working around it.
drm/udl: Suppress error print for -EPROTO at URB completion
The driver may receive -EPROTO at the URB completion when the device
gets disconnected, and it's a normal situation. Suppress the error
print for that, too.
Revert "drm/udl: Kill pending URBs at suspend and disconnect"
This reverts the recent fix commit e25d5954264d ("drm/udl: Kill pending URBs at suspend and disconnect")
as it turned out to lead to potential hangup at a disconnection, and
it doesn't help much for suspend/resume problem, either.
Restore the display mode whne resuming from suspend. Currently, the
display remains dark.
On resume, the CRTC's mode does not change, but the 'active' flag
changes to 'true'. Taking this into account when considering a mode
switch restores the display mode.
The bug is reproducable by using Gnome with udl and observing the
adapter's suspend/resume behavior.
Actually, the whole check added in udl_simple_display_pipe_enable()
about the crtc_state->mode_changed was bogus. We should drop the
whole check and always apply the mode change in this function.
[ tiwai -- Drop the mode_changed check entirely instead, per Daniel's
suggestion ]
Fixes: 997d33c35618 ("drm/udl: Inline DPMS code into CRTC enable and disable functions") Cc: <stable@vger.kernel.org> Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-2-tiwai@suse.de
Michał Winiarski [Wed, 31 Aug 2022 21:56:08 +0000 (23:56 +0200)]
drm/format: Split into more granular test cases
While we have multiple test cases, most of them check multiple
conditions, calling the function that is tested multiple times with
different arguments (with comments that indicate test case boundary).
This usually means that it can be easily converted into multiple test
cases.
Michał Winiarski [Wed, 31 Aug 2022 21:56:07 +0000 (23:56 +0200)]
drm/format: Use appropriate types in expect/assert
drm_format_info_* functions don't return bool, and the info variable is a
pointer.
Expecting non-NULL info will cause the test to crash if it is NULL in
checks that follow (which dereference it).
Use appropriate KUNIT_EXPECT/KUNIT_ASSERT variants.
Liang He [Fri, 22 Jul 2022 14:43:48 +0000 (22:43 +0800)]
drm/omap: dss: Fix refcount leak bugs
In dss_init_ports() and __dss_uninit_ports(), we should call
of_node_put() for the reference returned by of_graph_get_port_by_id()
in fail path or when it is not used anymore.
Maxime Ripard [Fri, 9 Sep 2022 09:31:16 +0000 (11:31 +0200)]
drm/sun4i: tv: Include drm_atomic.h
Commit ec491291dc94 ("drm/sun4i: tv: Merge mode_set into atomic_enable")
has introduced a call to drm_atomic_get_new_crtc_state(), but didn't
include drm_atomic.h.
On CONFIG_OF systems, this is fine because drm_atomic.h is included by
drm_of.h through drm_bridge.h. However, whenever CONFIG_OF isn't set, we
end up with a compilation error.
Fixes: ec491291dc94 ("drm/sun4i: tv: Merge mode_set into atomic_enable") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220909093116.4141982-1-maxime@cerno.tech
Imre Deak [Wed, 7 Sep 2022 14:25:42 +0000 (17:25 +0300)]
drm/dp_mst: Avoid deleting payloads for connectors staying enabled
When an MST connector stays enabled during a commit the connector's MST
state needs to be added to the atomic state, but the corresponding MST
payload allocation shouldn't be set for deletion; fix such modesets by
ensuring the above even if the connector was already enabled before the
modeset.
drm/ssd130x: Replace simple display helpers with the atomic helpers
The simple display pipeline is a set of helpers that can be used by DRM
drivers to avoid dealing with all the needed components and just define
a few functions to operate a simple display device with one full-screen
scanout buffer feeding a single output.
But it is arguable that this provides the correct level of abstraction
for simple drivers, and recently some have been ported from using these
simple display helpers to use the regular atomic helpers instead.
The rationale for this is that the simple display pipeline helpers don't
hide that much of the DRM complexity, while adding an indirection layer
that conflates the concepts of CRTCs and planes. This makes the helpers
less flexible and harder to be reused among different graphics drivers.
Also, for simple drivers, using the full atomic helpers doesn't require
a lot of additional code. So adding a simple display pipeline layer may
not be worth it.
For these reasons, let's follow that trend and make ssd130x a plain DRM
driver that creates its own primary plane, CRTC, enconder and connector.
drm/qxl: fix the suspend/resume issue on qxl device
Details:
Currently, when trying to suspend and resume with qxl device，
there are some error messages after resuming,
eventually caused to black screen and can't be recovered.
The first error message:
[ 64.668577][ C3] [drm] driver is in bug mode
This error is due to guest qxl driver
will call qxl_reinit_memslots(qdev) during system resume,
but didn't call qxl_io_reset(qdev) before this,
Then will cause the QXL_IO_MEMSLOT_ADD operation to fail on QEMU,
qxl->guest_bug flag will be set，As a result,
the QXL device can't communicate with guest qxl driver through the IO port.
after fix the first error,can success to resume and login to desktop,
but shortly after that will observe the second error message :
[ 353.095343][ T863] qxl 0000:00:02.0: object_init failed for (262144, 0x00000001)
[ 353.096660][ T863] [drm:qxl_gem_object_create [qxl]] *ERROR* Failed to allocate GEM object (260852, 1, 4096, -12)
[ 353.097277][ T863] [drm:qxl_alloc_ioctl [qxl]] *ERROR* qxl_alloc_ioctl: failed to create gem ret=-12
[ 368.197538][ T863] qxl 0000:00:02.0: object_init failed for (3149824, 0x00000001)
[ 368.197541][ T863] [drm:qxl_alloc_bo_reserved [qxl]] *ERROR* failed to allocate VRAM BO
The problem is caused by calling qxl_ring_init_hdr(qdev->release_ring)
in qxl_drm_resume() function.
When do QXL_IO_RESET,QEMU will call init_qxl_ram(),
so params like prod,cons,notify_on_cons and notify_on_prod
will be set to default value.
Ring push/pop actions for release_ring can be performed normally.
But call qxl_ring_init_hdr(qdev->release_ring)
will eventually set notify_on_prod to number of QXL_RELEASE_RING_SIZE,
affect the value of notify in qxl_push_free_res() function always be false,
QEMU will no longer send events of QXL_INTERRUPT_DISPLAY to the
guest qxl driver，so qxl_ring_pop() will never been called anymore，
and can't do dma_fence_signal(),result to ttm_bo_wait_ctx(bo, ctx)
always return EBUSY,fail to call qxl_bo_create().
Test scenario:
1) start virtual machine with qemu command "-device qxl-vga"
2) click suspend botton to enter suspend mode
3) resume and observe the error message in kernel logs,screen will be black
Let's fix this by reset io and remove the qxl_ring_init_hdr calling.
VGA_IS1_RC is the color mode register (VGA_IS1_RM the one for monochrome
mode, note C vs. M at the end). So when using VGA_IS1_RC make sure the
vga device is actually in color mode and set the corresponding bit in the
misc register.
Reproducible when booting VMs in UEFI mode with some edk2 versions (edk2
fix is on the way too). Doesn't happen in BIOS mode because in that
case the vgabios already flips the bit.
Maxime Ripard [Mon, 29 Aug 2022 13:11:54 +0000 (15:11 +0200)]
drm/sun4i: tv: Add missing reset assertion
The reset line is deasserted at bind, and asserted if we ever encounter an
error there. However, it's never asserted in unbind which will lead to a
resource unbalance.
Maxime Ripard [Mon, 29 Aug 2022 13:11:53 +0000 (15:11 +0200)]
drm/sun4i: tv: Rename error label
The other error labels in sun4i_tv_bind() are named after the task they
perform (err_disable_clk to call clk_disable_unprepare for example).
However, the err_cleanup_connector is named after the calling site
(drm_connector_init failing) and will actually cleanup the encoder. Let's
rename it to err_cleanup_encoder to be consistent.
Mateusz Kwiatkowski [Mon, 29 Aug 2022 13:11:42 +0000 (15:11 +0200)]
drm/vc4: vec: Fix timings for VEC modes
This commit fixes vertical timings of the VEC (composite output) modes
to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R
standards.
Previous timings were actually defined as 502 and 601 lines, resulting
in non-standard 62.69 Hz and 52 Hz signals being generated,
respectively.
Mateusz Kwiatkowski [Mon, 29 Aug 2022 13:11:40 +0000 (15:11 +0200)]
drm/vc4: vec: Refactor VEC TV mode setting
Change the mode_set function pointer logic to declarative config0,
config1 and custom_freq fields, to make TV mode setting logic more
concise and uniform.
Randy Dunlap [Mon, 4 Apr 2022 21:30:40 +0000 (14:30 -0700)]
drm/scheduler: quieten kernel-doc warnings
Fix kernel-doc warnings in gpu_scheduler.h and sched_main.c.
Quashes these warnings:
include/drm/gpu_scheduler.h:332: warning: missing initial short description on line:
* struct drm_sched_backend_ops
include/drm/gpu_scheduler.h:412: warning: missing initial short description on line:
* struct drm_gpu_scheduler
include/drm/gpu_scheduler.h:461: warning: Function parameter or member 'dev' not described in 'drm_gpu_scheduler'
drivers/gpu/drm/scheduler/sched_main.c:201: warning: missing initial short description on line:
* drm_sched_dependency_optimized
drivers/gpu/drm/scheduler/sched_main.c:995: warning: Function parameter or member 'dev' not described in 'drm_sched_init'
Fixes: 2d33948e4e00 ("drm/scheduler: add documentation") Fixes: 8ab62eda177b ("drm/sched: Add device pointer to drm_gpu_scheduler") Fixes: 542cff7893a3 ("drm/sched: Avoid lockdep spalt on killing a processes") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Cc: Nayan Deshmukh <nayan26deshmukh@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Jiawei Gu <Jiawei.Gu@amd.com> Cc: dri-devel@lists.freedesktop.org Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220404213040.12912-1-rdunlap@infradead.org
Xin Ji [Sat, 3 Sep 2022 13:08:33 +0000 (21:08 +0800)]
drm/bridge: anx7625: Set HPD irq detect window to 2ms
Some panels trigger HPD irq due to noise, the HPD debounce
may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
This patch set HPD irq detection window to 2ms to
tolerate the HPD noise.
Igor Torrente [Mon, 5 Sep 2022 19:08:10 +0000 (16:08 -0300)]
drm: vkms: Adds XRGB_16161616 and ARGB_1616161616 formats
This will be useful to write tests that depends on these formats.
ARGB and XRGB follows the a similar implementation of the former formats.
Just adjusting for 16 bits per channel.
V3: Adapt the handlers to the new format introduced in patch 7 V3.
V5: Minor improvements
Added le16_to_cpu/cpu_to_le16 to the 16 bits color read/writes.
Igor Torrente [Mon, 5 Sep 2022 19:08:09 +0000 (16:08 -0300)]
drm: vkms: Supports to the case where primary plane doesn't match the CRTC
We will remove the current assumption that the primary plane has the
same size and position as CRTC and that the primary plane is the
bottom-most in zpos order, or is even enabled. At least as far
as the blending machinery is concerned.
For that we will add CRTC dimension information to `vkms_crtc_state`
and add a opaque black backgound color.
Because now we need to fill the background, we had a loss in
performance with this change. Results running the IGT[1] test
`igt@kms_cursor_crc@pipe-a-cursor-512x512-onscreen` ten times:
| Frametime |
|:--------------------------------------------:|
| Implementation | Previous | This commit |
|:---------------:|:---------:|:--------------:|
| frametime range | 5~18 ms | 10~22 ms |
| Average | 8.47 ms | 12.32 ms |
V6: Improve the commit description (Pekka Paalanen).
Update some comments (Pekka Paalanen).
Remove some fields from `vkms_crtc_state` and move where
some variables are set (Pekka Paalanen).
Igor Torrente [Mon, 5 Sep 2022 19:08:08 +0000 (16:08 -0300)]
drm: vkms: Refactor the plane composer to accept new formats
Currently the blend function only accepts XRGB_8888 and ARGB_8888
as a color input.
This patch refactors all the functions related to the plane composition
to overcome this limitation.
The pixels blend is done using the new internal format. And new handlers
are being added to convert a specific format to/from this internal format.
So the blend operation depends on these handlers to convert to this common
format. The blended result, if necessary, is converted to the writeback
buffer format.
This patch introduces three major differences to the blend function.
1 - All the planes are blended at once.
2 - The blend calculus is done as per line instead of per pixel.
3 - It is responsible to calculates the CRC and writing the writeback
buffer(if necessary).
These changes allow us to allocate way less memory in the intermediate
buffer to compute these operations. Because now we don't need to
have the entire intermediate image lines at once, just one line is
enough.
Beyond memory, we also have a minor performance benefit from all
these changes. Results running the IGT[1] test
`igt@kms_cursor_crc@pipe-a-cursor-512x512-onscreen` ten times:
| Frametime |
|:------------------------------------------:|
| Implementation | Current | This commit |
|:---------------:|:---------:|:------------:|
| frametime range | 9~22 ms | 5~17 ms |
| Average | 11.4 ms | 7.8 ms |
V2: Improves the performance drastically, by performing the operations
per-line and not per-pixel(Pekka Paalanen).
Minor improvements(Pekka Paalanen).
V3: Changes the code to blend the planes all at once. This improves
performance, memory consumption, and removes much of the weirdness
of the V2(Pekka Paalanen and me).
Minor improvements(Pekka Paalanen and me).
V4: Rebase the code and adapt it to the new NUM_OVERLAY_PLANES constant.
V5: Minor checkpatch fixes and the removal of TO-DO item(Melissa Wen).
Several security/robustness improvents(Pekka Paalanen).
Removes check_planes_x_bounds function and allows partial
partly off-screen(Pekka Paalanen).
V6: Fix a mismatch of some variable sizes (Pekka Paalanen).
Several minor improvements (Pekka Paalanen).
Igor Torrente [Mon, 5 Sep 2022 19:08:07 +0000 (16:08 -0300)]
drm: vkms: Add fb information to `vkms_writeback_job`
This commit is the groundwork to introduce new formats to the planes and
writeback buffer. As part of it, a new buffer metadata field is added to
`vkms_writeback_job`, this metadata is represented by the `vkms_frame_info`
struct.
Also adds two new function pointers (`line_to_frame_func` and
`frame_to_line_func`) are defined to handle format conversion
from/to internal format.
A new internal format(`struct pixel_argb_u16`) is introduced to deal with
all possible inputs. It consists of 16 bits fields that represent each of
the channels.
These things will allow us, in the future, to have different compositing
and wb format types.
V2: Change the code to get the drm_framebuffer reference and not copy its
contents (Thomas Zimmermann).
V3: Drop the refcount in the wb code (Thomas Zimmermann).
V5: Add {wb,plane}_format_transform_func to vkms_writeback_job
and vkms_plane_state (Pekka Paalanen)
V6: Improvements to some struct/struct members names (Pekka Paalanen).
Splits this patch in two (Pekka Paalanen).
V7: Replace line_to_frame_func and frame_to_line_func typedefs
with the function signature and void* (Melissa Wen).
Igor Torrente [Mon, 5 Sep 2022 19:08:05 +0000 (16:08 -0300)]
drm: drm_atomic_helper: Add a new helper to deal with the writeback connector validation
Add a helper function to validate the connector configuration received in
the encoder atomic_check by the drivers.
So the drivers don't need to do these common validations themselves.
V2: Move the format verification to a new helper at the drm_atomic_helper.c
(Thomas Zimmermann).
V3: Format check improvements (Leandro Ribeiro).
Minor improvements(Thomas Zimmermann).
V5: Fix some grammar issues in the commit message (André Almeida).
Igor Torrente [Mon, 5 Sep 2022 19:08:04 +0000 (16:08 -0300)]
drm: vkms: Rename `vkms_composer` to `vkms_frame_info`
Changes the name of this struct to a more meaningful name.
A name that represents better what this struct is about.
Composer is the code that do the compositing of the planes.
This struct contains information on the frame used in the output
composition. Thus, vkms_frame_info is a better name to represent
this.
V5: Fix a commit message typo(Melissa Wen).
V6: Fix wrong iosys_map_is_null verification at compose_plane
(Melissa Wen).
Simon Ser [Mon, 1 Aug 2022 13:38:02 +0000 (13:38 +0000)]
drm: hide unregistered connectors from GETCONNECTOR IOCTL
When registering a connector, the kernel sends a hotplug uevent in
drm_connector_register(). When unregistering a connector, drivers
are expected to send a uevent as well. However, user-space has no way
to figure out that the connector isn't registered anymore: it'll still
be reported in GETCONNECTOR IOCTLs.
The documentation for DRM_CONNECTOR_UNREGISTERED states:
> The connector […] has since been unregistered and removed from
> userspace, or the connector was unregistered before it had a chance
> to be exposed to userspace
Jitao Shi [Thu, 1 Sep 2022 04:41:48 +0000 (12:41 +0800)]
drm/mediatek: dp: Add hpd debounce
From the DP spec 1.4a chapter 3.3, upstream devices should implement
HPD signal de-bouncing on an external connection.
A period of 100ms should be used to detect an HPD connect event.
To cover these cases, HPD de-bounce should be implemented only after
HPD low has been detected for at least 100ms.
Therefore,
1. If HPD is low (which means plugging out) for longer than 100ms:
we need to do de-bouncing (which means we need to wait for 100ms).
2. If HPD low is for less than 100ms:
we don't need to care about the de-bouncing.
In this patch, we start a 100ms timer and use a need_debounce boolean
to implement the feature.
Two cases when HPD is high:
1. If the timer is expired (>100ms):
- need_debounce is true.
- When HPD high (plugging event comes), need_debounce will be true
and then we need to do de-bouncing (wait for 100ms).
2. If the timer is not expired (<100ms):
- need_debounce is false.
- When HPD high (plugging event comes), need_debounce will be false
and no need to do de-bouncing.
drm/mediatek: dp: Add MT8195 External DisplayPort support
Add External DisplayPort support to the MT8195 eDP driver.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com> Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-9-rex-bc.chen@mediatek.com
It's not necessary to have a next_bridge for DP device, so we add this
patch to judge this.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-8-rex-bc.chen@mediatek.com
drm/mediatek: dp: Add multiple calibration data formats support
The calibration data formats of eDP and DP are different. We add
"const struct mtk_dp_efuse_fmt *efuse_fmt" to the device data to
define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-7-rex-bc.chen@mediatek.com
drm/mediatek: dp: Add multiple smc commands support
The smc commands of eDP and DP are different. We add smc_cmd to the
device data to define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-6-rex-bc.chen@mediatek.com
drm/mediatek: dp: Add multiple bridge types support
The bridge types of eDP and DP are different. We add device data to
this driver and add bridge_type to the device data to define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-5-rex-bc.chen@mediatek.com
This patch adds a embedded displayport driver for the MediaTek mt8195 SoC.
It supports the MT8195, the embedded DisplayPort units. It offers
DisplayPort 1.4 with up to 4 lanes.
The driver creates a child device for the phy. The child device will
never exist without the parent being active. As they are sharing a
register range, the parent passes a regmap pointer to the child so that
both can work with the same register range. The phy driver sets device
data that is read by the parent to get the phy device that can be used
to control the phy properties.
This driver is based on an initial version by
Jitao shi <jitao.shi@mediatek.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Guillaume Ranquet <granquet@baylibre.com> Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-4-rex-bc.chen@mediatek.com
Markus Schneider-Pargmann [Thu, 1 Sep 2022 04:41:41 +0000 (12:41 +0800)]
video/hdmi: Add audio_infoframe packing for DP
Similar to HDMI, DP uses audio infoframes as well which are structured
very similar to the HDMI ones.
This patch adds a helper function to pack the HDMI audio infoframe for
DP, called hdmi_audio_infoframe_pack_for_dp().
hdmi_audio_infoframe_pack_only() is split into two parts. One of them
packs the payload only and can be used for HDMI and DP.
Also constify the frame parameter in hdmi_audio_infoframe_check() as
it is passed to hdmi_audio_infoframe_check_only() which expects a const.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Guillaume Ranquet <granquet@baylibre.com> Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-3-rex-bc.chen@mediatek.com
Markus Schneider-Pargmann [Thu, 1 Sep 2022 04:41:40 +0000 (12:41 +0800)]
dt-bindings: mediatek,dp: Add Display Port binding
This controller is present on several mediatek hardware. Currently
mt8195 and mt8395 have this controller without a functional difference,
so only one compatible field is added.
The controller can have two forms, as a normal display port and as an
embedded display port.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Guillaume Ranquet <granquet@baylibre.com> Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-2-rex-bc.chen@mediatek.com
Chris Morgan [Fri, 2 Sep 2022 15:39:06 +0000 (10:39 -0500)]
drm/bridge: chrontel-ch7033: Add byteswap order setting
Add the option to set the byteswap order in the devicetree. For the
official HDMI DIP for the NTC CHIP the byteswap order needs to be
RGB, however the driver sets it as BGR. With this patch the driver
will remain at BGR unless manually specified via devicetree.
Laurent Pinchart [Wed, 31 Aug 2022 08:26:52 +0000 (11:26 +0300)]
drm/bridge: ti-sn65dsi86: Support DisplayPort (non-eDP) mode
Despite the SN65DSI86 being an eDP bridge, on some systems its output is
routed to a DisplayPort connector. Enable DisplayPort mode when the next
component in the display pipeline is detected as a DisplayPort
connector, and disable eDP features in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reworked to set bridge type based on the next bridge/connector. Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
--
Changes since v1/RFC:
- Rebased on top of "drm/bridge: ti-sn65dsi86: switch to
devm_drm_of_get_bridge"
- eDP/DP mode determined from the next bridge connector type.
Changes since v2:
- Remove setting of Standard DP Scrambler Seed. (It's read-only).
- Prevent setting DP_EDP_CONFIGURATION_SET in
ti_sn_bridge_atomic_enable()
- Use Doug's suggested text for disabling ASSR on DP mode.
Changes since v3:
- Remove ASSR_CONTROL definition
Changes since v4:
- Refactor code to configure the DP/eDP scrambler in one place.
Imre Deak [Thu, 1 Sep 2022 16:19:33 +0000 (19:19 +0300)]
drm/i915/dp_mst: Fix mst_mgr lookup during atomic check
If an MST connector was disabled in the old state during a commit, the
connector's best_encoder will be NULL, so we can't look up mst_mgr via
it. Do the lookup instead via intel_connector->mst_port which always
points to the primary encoder.
Michał Winiarski [Wed, 17 Aug 2022 21:12:36 +0000 (23:12 +0200)]
drm/cmdline-parser: Use assert when needed
Expecting to observe a specific value, when the function responsible for
setting the value has failed will lead to extra noise in test output.
Use assert when the situation calls for it.
Also - very small tidying up around the changed areas (whitespace).
v2: Leave out the locals (drm_connector is huge) (lkp)
Michał Winiarski [Wed, 17 Aug 2022 21:12:35 +0000 (23:12 +0200)]
drm/cmdline-parser: Merge negative tests
Negative tests can be expressed as a single parameterized test case,
which highlights that we're following the same test logic (passing
invalid cmdline and expecting drm_mode_parse_command_line_for_connector
to fail), which improves readability.
v2: s/negative/invalid to be consistent with other testcases in DRM
projects / users / dwmw2 / linux.git / log