Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Acked-by: Scott Wood <oss@buserror.net> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
setup_profiling_timer() is only needed when CONFIG_PROFILING is enabled.
Fixes the following W=1 warning when CONFIG_PROFILING=n:
linux/arch/powerpc/kernel/smp.c:1638:5: error: no previous prototype for ‘setup_profiling_timer’
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible for all CPUs to miss the pending cpumask becoming clear,
and then nobody resetting it, which will cause the lockup detector to
stop working. It will eventually expire, but watchdog_smp_panic will
avoid doing anything if the pending mask is clear and it will never be
reset.
Order the cpumask clear vs the subsequent test to close this race.
Add an extra check for an empty pending mask when the watchdog fires and
finds its bit still clear, to try to catch any other possible races or
bugs here and keep the watchdog working. The extra test in
arch_touch_nmi_watchdog is required to prevent the new warning from
firing off.
In handle_interruption(), we call faulthandler_disabled() to check whether the
fault handler is not disabled. If the fault handler is disabled, we immediately
call do_page_fault(). It then calls faulthandler_disabled(). If disabled,
do_page_fault() attempts to fixup the exception by jumping to no_context:
no_context:
if (!user_mode(regs) && fixup_exception(regs)) {
return;
}
struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state. It also avoids a register
read to obtain the current state of output signals.
When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync. That may cause
a subsequent register write to be incorrectly skipped. Fix it before
it trips somebody up.
This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb
So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup(). Therefore,
a stable designation seems unnecessary.
pl010_set_termios() briefly resets the CR register to zero.
Where does this register write come from?
The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock. ambauart_set_termios() also
modified that register. To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts. That is achieved by
writing zero to the CR register.
However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591
That rendered the CR register write obsolete. Drop it.
The RPMh regulator driver is much newer and gets more attention, which in
consequence makes it do a few things better. Update qcom_smd-regulator's
probe function to mimic what rpmh-regulator does to address a couple of
issues:
- Probe defer now works correctly, before it used to, well,
kinda just die.. This fixes reliable probing on (at least) PM8994,
because Linux apparently cannot deal with supply map dependencies yet..
- Regulator data is now matched more sanely: regulator data is matched
against each individual regulator node name and throwing an -EINVAL if
data is missing, instead of just assuming everything is fine and
iterating over all subsequent array members.
- status = "disabled" will now work for disabling individual regulators in
DT. Previously it didn't seem to do much if anything at all.
The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.
However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit c27aa56a72b8 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we're looking for leafs that point to a data extent we want to record
the extent items that point at our bytenr. At this point we have the
reference and we know for a fact that this leaf should have a reference
to our bytenr. However if there's some sort of corruption we may not
find any references to our leaf, and thus could end up with eie == NULL.
Replace this BUG_ON() with an ASSERT() and then return -EUCLEAN for the
mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We search for an extent entry with .offset = -1, which shouldn't be a
thing, but corruption happens. Add an ASSERT() for the developers,
return -EUCLEAN for mortals.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The EC/ACPI firmware on Lenovo ThinkPads used to report a status
of "Unknown" when the battery is between the charge start and
charge stop thresholds. On Windows, it reports "Not Charging"
so the quirk has been added to also report correctly.
Now the "status" attribute returns "Not Charging" when the
battery on ThinkPads is not physicaly charging.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some boards(like RX550) seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
after add this patch,the maximum GPU VRAM size is 64GB,
otherwise only 64GB vram size will be used.
According to ACPI 6.4, Section 16.2, the CPU cache flushing is
required on entering to S1, S2, and S3, but the ACPICA code
flushes the CPU cache regardless of the sleep state.
Blind cache flush on entering S5 causes problems for TDX.
Flushing happens with WBINVD that is not supported in the TDX
environment.
TDX only supports S5 and adjusting ACPICA code to conform to the
spec more strictly fixes the issue.
Link: https://github.com/acpica/acpica/commit/3dd7e1f3 Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If Operand[0] is a reference of the ACPI_REFCLASS_REFOF class,
acpi_ex_opcode_1A_0T_1R () calls acpi_ns_get_attached_object () to
obtain return_desc which may require additional resolution with
the help of acpi_ex_read_data_from_field (). If the latter fails,
the reference counter of the original return_desc is decremented
which is incorrect, because acpi_ns_get_attached_object () does not
increment the reference counter of the object returned by it.
This issue may lead to premature deletion of the attached object
while it is still attached and a use-after-free and crash in the
host OS. For example, this may happen when on evaluation of ref_of()
a local region field where there is no registered handler for the
given Operation Region.
Fix it by making acpi_ex_opcode_1A_0T_1R () return Status right away
after a acpi_ex_read_data_from_field () failure.
Link: https://github.com/acpica/acpica/commit/d984f120 Link: https://github.com/acpica/acpica/pull/685 Reported-by: Lenny Szubowicz <lszubowi@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If original_count is 0 in acpi_ut_update_ref_count (),
acpi_ut_delete_internal_obj () is invoked for the target object, which is
incorrect, because that object has been deleted once already and the
memory allocated to store it may have been reclaimed and allocated
for a different purpose by the host OS. Moreover, a confusing debug
message following the "Reference Count is already zero, cannot
decrement" warning is printed in that case.
To fix this issue, make acpi_ut_update_ref_count () return after finding
that original_count is 0 and printing the above warning.
Link: https://github.com/acpica/acpica/commit/c11af67d Link: https://github.com/acpica/acpica/pull/652 Reported-by: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current ACPI_ACCESS_*_WIDTH defines do not provide a way to
test that size is small enough to not cause an overflow when
applied to a 32-bit integer.
Rather than adding more magic numbers, add ACPI_ACCESS_*_SHIFT,
ACPI_ACCESS_*_MAX, and ACPI_ACCESS_*_DEFAULT #defines and
redefine ACPI_ACCESS_*_WIDTH in terms of the new #defines.
This was inititally reported on Linux where a size of 102 in
ACPI_ACCESS_BIT_WIDTH caused an overflow error in the SPCR
initialization code.
Link: https://github.com/acpica/acpica/commit/bc02c76d Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GC task can deadlock in read_cache_page() because it may attempt
to release a page that is actually allocated by another task in
jffs2_write_begin().
The reason is that in jffs2_write_begin() there is a small window
a cache page is allocated for use but not set Uptodate yet.
This ends up with a deadlock between two tasks:
1) A task (e.g. file copy)
- jffs2_write_begin() locks a cache page
- jffs2_write_end() tries to lock "alloc_sem" from
jffs2_reserve_space() <-- STUCK
2) GC task (jffs2_gcd_mtd3)
- jffs2_garbage_collect_pass() locks "alloc_sem"
- try to lock the same cache page in read_cache_page() <-- STUCK
So to avoid this deadlock, hold "alloc_sem" in jffs2_write_begin()
while reading data in a cache page.
The function names init_registers() and restore_registers() are used
in several net/ethernet/ and gpu/drm/ drivers for other purposes (not
calls to UML functions), so rename them.
This fixes multiple build errors.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: linux-um@lists.infradead.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RADA might include in the Rx frame the MIC and CRC bytes.
These bytes should be removed for non monitor interfaces and
should not be passed to mac80211.
Fix the Rx processing to remove the extra bytes on non monitor
cases.
When CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, iwlwifi crashes
when the opmode module cannot be loaded, due to completing
the completion before using drv->dev, which can then already
be freed.
Fix this by removing the (fairly useless) message. Moving the
completion later causes a deadlock instead, so that's not an
option.
If firmware load fails after having loaded some parts of the
firmware, e.g. the IML image, then this would leak. For the
host command list we'd end up running into a WARN on the next
attempt to load another firmware image.
Fix this by calling iwl_dealloc_ucode() on failures, and make
that also clear the data so we start fresh on the next round.
Large pkt_len can lead to out-out-bound memcpy. Current
ath9k_hif_usb_rx_stream allows combining the content of two urb
inputs to one pkt. The first input can indicate the size of the
pkt. Any remaining size is saved in hif_dev->rx_remain_len.
While processing the next input, memcpy is used with rx_remain_len.
4-byte pkt_len can go up to 0xffff, while a single input is 0x4000
maximum in size (MAX_RX_BUF_SIZE). Thus, the patch adds a check for
pkt_len which must not exceed 2 * MAX_RX_BUG_SIZE.
BUG: KASAN: slab-out-of-bounds in ath9k_hif_usb_rx_cb+0x490/0xed7 [ath9k_htc]
Read of size 46393 at addr ffff888018798000 by task kworker/0:1/23
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the value of pkt_tag to ATH_USB_RX_STREAM_MODE_TAG in QEMU
emulation, I found the KASAN report. The bug is triggerable whenever
pkt_len is above two MAX_RX_BUG_SIZE. I used the same input that crashes
to test the driver works when applying the patch.
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
Due to the audit control mutex necessary for serializing audit
userspace messages we haven't been able to block/penalize userspace
processes that attempt to send audit records while the system is
under audit pressure. The result is that privileged userspace
applications have a priority boost with respect to audit as they are
not bound by the same audit queue throttling as the other tasks on
the system.
This patch attempts to restore some balance to the system when under
audit pressure by blocking these privileged userspace tasks after
they have finished their audit processing, and dropped the audit
control mutex, but before they return to userspace.
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com> Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of saa7146_register_device(). There is a dereference of
dev->vv_data in saa7146_vv_release(), which could lead to a NULL
pointer dereference on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_GEMINI=m show no new warnings,
and our static analyzer no longer warns about this code.
The WARN_ONCE() in bpf_warn_invalid_xdp_action() can be triggered by
any bugged program, and even attaching a correct program to a NIC
not supporting the given action.
The resulting splat, beyond polluting the logs, fouls automated tools:
e.g. a syzkaller reproducers using an XDP program returning an
unsupported action will never pass validation.
Replace the WARN_ONCE with a less intrusive pr_warn_once().
When updating Rx and Tx queue kobjects, the queue count should always be
updated to match the queue kobjects count. This was not done in the net
device unregistration path, fix it. Tracking all queue count updates
will allow in a following up patch to detect illegal updates.
Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. In hexium_detach(), saa7146_vv_release()
will be called and there is a dereference of dev->vv_data in
saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init() according to the following logic.
Both hexium_attach() and hexium_detach() are callback functions of
the variable 'extension', so there exists a possible call chain directly
from hexium_attach() to hexium_detach():
hexium_attach(dev, info) -- fail to alloc memory to dev->vv_data
| in saa7146_vv_init().
|
|
hexium_detach() -- a dereference of dev->vv_data in saa7146_vv_release()
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_ORION=m show no new warnings,
and our static analyzer no longer warns about this code.
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
We need to check the max request size that is from user space before
allocating pages. If the request size exceeds the limit, return -EINVAL.
This check can avoid the warning below from page allocator.
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.
The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ
The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.
Attached is the KASAN report from fuzzing.
BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.
I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.
Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the configuration used by the b850v3, the STDP2690 is used to read EDID
data whilst it's the STDP4028 which can detect when monitors are connected.
This can result in problems at boot with monitors connected when the
STDP4028 is probed first, a monitor is detected and an attempt is made to
read the EDID data before the STDP2690 has probed:
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
A out-of-bounds bug can be triggered by an interrupt, the reason for
this bug is the lack of checking of register values.
In flexcop_pci_isr, the driver reads value from a register and uses it as
a dma address. Finally, this address will be passed to the count parameter
of find_next_packet. If this value is larger than the size of dma, the
index of buffer will be out-of-bounds.
Fix this by adding a check after reading the value of the register.
The following KASAN report reveals it:
BUG: KASAN: slab-out-of-bounds in find_next_packet
drivers/media/dvb-core/dvb_demux.c:528 [inline]
BUG: KASAN: slab-out-of-bounds in _dvb_dmx_swfilter
drivers/media/dvb-core/dvb_demux.c:572 [inline]
BUG: KASAN: slab-out-of-bounds in dvb_dmx_swfilter+0x3fa/0x420
drivers/media/dvb-core/dvb_demux.c:603
Read of size 1 at addr ffff8880608c00a0 by task swapper/2/0
Memory state around the buggy address: ffff8880608bff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8880608c0000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8880608c0080: 00 00 00 00 fc fc fc fc fc fc fc fc 00 00 00 00
^ ffff8880608c0100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8880608c0180: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.
The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655e3
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.
It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.
There have been reports of the WFI timing out on some boards, and a
patch was proposed to just remove it. This stuff is rather fragile,
and I believe the WFI might be needed with our FW prior to GM200.
However, we probably should not be touching PMU during init on GPUs
where we depend on NVIDIA FW, outside of limited circumstances, so
this should be a somewhat safer change that achieves the desired
result.
Reported-by: Diego Viola <diego.viola@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Karol Herbst <kherbst@redhat.com> Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/10 Signed-off-by: Sasha Levin <sashal@kernel.org>
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START,
I got the null-ptr-deref bug. I believe the bug is triggerable whenever
cmd->odata is NULL. After patching, I tested with the same input and no
longer see the KASAN report.
The issue is that we received a DLM message for a user lock but the
destination lock is a kernel lock. Note that the address which is trying
to derefence is 00000000deadbeef, which is in a kernel lock
lkb->lkb_astparam, this field should never be derefenced by the DLM
kernel stack. In case of a user lock lkb->lkb_astparam is lkb->lkb_ua
(memory is shared by a union field). The struct lkb_ua will be handled
by the DLM kernel stack but on a kernel lock it will contain invalid
data and ends in most likely crashing the kernel.
The MIPS BMC63XX subarch does not provide/support clk_set_parent().
This causes build errors in a few drivers, so add a simple implementation
of that function so that callers of it will build without errors.
Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs." ) Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When firmware load failed, kernel report task hung as follows:
INFO: task xrun:5191 blocked for more than 147 seconds.
Tainted: G W 5.16.0-rc5-next-20211220+ #11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:xrun state:D stack: 0 pid: 5191 ppid: 270 flags:0x00000004
Call Trace:
__schedule+0xc12/0x4b50 kernel/sched/core.c:4986
schedule+0xd7/0x260 kernel/sched/core.c:6369 (discriminator 1)
schedule_timeout+0x7aa/0xa80 kernel/time/timer.c:1857
wait_for_completion+0x181/0x290 kernel/sched/completion.c:85
lattice_ecp3_remove+0x32/0x40 drivers/misc/lattice-ecp3-config.c:221
spi_remove+0x72/0xb0 drivers/spi/spi.c:409
lattice_ecp3_remove() wait for signals from firmware loading, but when
load failed, firmware_load() does not send this signal. This cause
device remove hung. Fix it by sending signal even if load failed.
Because of the potential failure of the ioremap(), the buf->area could
be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.
Fixes: f09aecd50f39 ("ASoC: SAMSUNG: Add I2S0 internal dma driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20211228034026.1659385-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turns out to be possible for hotplugging out a device to reach the
stage of tearing down the device's group and default domain before the
domain's flush queue has drained naturally. At this point, it is then
possible for the timeout to expire just before the del_timer() call
in free_iova_flush_queue(), such that we then proceed to free the FQ
resources while fq_flush_timeout() is still accessing them on another
CPU. Crashes due to this have been observed in the wild while removing
NVMe devices.
Close the race window by using del_timer_sync() to safely wait for any
active timeout handler to finish before we start to free things. We
already avoid any locking in free_iova_flush_queue() since the FQ is
supposed to be inactive anyway, so the potential deadlock scenario does
not apply.
The last driver referencing the slave_id on Marvell PXA and MMP platforms
was the SPI driver, but this stopped doing so a long time ago, so the
TODO from the earlier patch can no be removed.
Fixes: b729bf34535e ("spi/pxa2xx: Don't use slave_id of dma_slave_config") Fixes: 13b3006b8ebd ("dma: mmp_pdma: add filter function") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20211122222203.4103644-7-arnd@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value of device_property_read_u32_array() is not always 0.
To catch the exception in case that devm_kzalloc failed and the
rt5663->imp_table was NULL, which caused the failure of
device_property_read_u32_array.
Fixes: 450f0f6a8fb4 ("ASoC: rt5663: Add the manual offset field to compensate the DC offset") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Link: https://lore.kernel.org/r/20211215031550.70702-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, ib_find_gid() will stop searching after encountering the first
empty GID table entry. This behavior is wrong since neither IB nor RoCE
spec enforce tightly packed GID tables.
For example, when a valid GID entry exists at index N, and if a GID entry
is empty at index N-1, ib_find_gid() will fail to find the valid entry.
Fix it by making ib_find_gid() continue searching even after encountering
missing entries.
Fixes: 5eb620c81ce3 ("IB/core: Add helpers for uncached GID and P_Key searches") Link: https://lore.kernel.org/r/e55d331b96cecfc2cf19803d16e7109ea966882d.1639055490.git.leonro@nvidia.com Signed-off-by: Avihai Horon <avihaih@nvidia.com> Reviewed-by: Mark Zhang <markzhang@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver data pointer must be set before any callbacks are registered
that use that pointer. Hence move the initialization of that pointer from
after the ufshcd_init() call to inside ufshcd_init().
Link: https://lore.kernel.org/r/20211203231950.193369-7-bvanassche@acm.org Fixes: 3b1d05807a9a ("[SCSI] ufs: Segregate PCI Specific Code") Reported-by: Alexey Dobriyan <adobriyan@gmail.com> Tested-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Table descriptors were being installed without properly formatting the
address using paddr_to_iopte, which does not match up with the
iopte_deref in __arm_lpae_map. This is incorrect for the LPAE pte
format, as it does not handle the high bits properly.
This was found on Apple T6000 DARTs, which require a new pte format
(different shift); adding support for that to
paddr_to_iopte/iopte_to_paddr caused it to break badly, as even <48-bit
addresses would end up incorrect in that case.
Fixes: 6c89928ff7a0 ("iommu/io-pgtable-arm: Support 52-bit physical address") Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Hector Martin <marcan@marcan.st> Link: https://lore.kernel.org/r/20211120031343.88034-1-marcan@marcan.st Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using MKWORD() on a byte-sized variable results in OOB read. Expand the
size of the reserved area so both MKWORD and MKBYTE continue to work
without overflow. Silences this warning on a -Warray-bounds build:
drivers/char/mwave/3780i.h:346:22: error: array subscript 'short unsigned int[0]' is partly outside array bounds of 'DSP_ISA_SLAVE_CONTROL[1]' [-Werror=array-bounds]
346 | #define MKWORD(var) (*((unsigned short *)(&var)))
| ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/char/mwave/3780i.h:356:40: note: in definition of macro 'OutWordDsp'
356 | #define OutWordDsp(index,value) outw(value,usDspBaseIO+index)
| ^~~~~
drivers/char/mwave/3780i.c:373:41: note: in expansion of macro 'MKWORD'
373 | OutWordDsp(DSP_IsaSlaveControl, MKWORD(rSlaveControl));
| ^~~~~~
drivers/char/mwave/3780i.c:358:31: note: while referencing 'rSlaveControl'
358 | DSP_ISA_SLAVE_CONTROL rSlaveControl;
| ^~~~~~~~~~~~~
Fix compile error when OSS_DEBUG is enabled:
sound/core/oss/pcm_oss.c: In function 'snd_pcm_oss_set_trigger':
sound/core/oss/pcm_oss.c:2055:10: error: 'substream' undeclared (first
use in this function); did you mean 'csubstream'?
pcm_dbg(substream->pcm, "pcm_oss: trigger = 0x%x\n", trigger);
^
Commit f37fe2f9987b ("ASoC: uniphier: add support for UniPhier AIO common
driver") adds configs SND_SOC_UNIPHIER_{LD11,PXS2}, which select the
non-existing config SND_SOC_UNIPHIER_AIO_DMA.
Probably, there is actually no further config intended to be selected
here. So, just drop selecting the non-existing config.
Fixes: f37fe2f9987b ("ASoC: uniphier: add support for UniPhier AIO common driver") Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20211125095158.8394-2-lukas.bulwahn@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
prom_getprop() can return PROM_ERROR. Binary operator can not identify
it.
Fixes: 94d2dde738a5 ("[POWERPC] Efika: prune fixups and make them more carefull") Signed-off-by: Peiwei Hu <jlu.hpw@foxmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/tencent_BA28CC6897B7C95A92EB8C580B5D18589105@qq.com Signed-off-by: Sasha Levin <sashal@kernel.org>
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
A user reported FITRIM ioctl failing for him on ext4 on some devices
without apparent reason. After some debugging we've found out that
these devices (being LVM volumes) report rather large discard
granularity of 42MB and the filesystem had 1k blocksize and thus group
size of 8MB. Because ext4 FITRIM implementation puts discard
granularity into minlen, ext4_trim_fs() declared the trim request as
invalid. However just silently doing nothing seems to be a more
appropriate reaction to such combination of parameters since user did
not specify anything wrong.
CC: Lukas Czerner <lczerner@redhat.com> Fixes: 5c2ed62fd447 ("ext4: Adjust minlen with discard_granularity in the FITRIM ioctl") Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20211112152202.26614-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com Fixes: 2a36d7083438 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to set TASK_INTERRUPTIBLE before calling kthread_should_stop().
Otherwise, kthread_stop() might see that the pccardd thread is still
in TASK_RUNNING state and fail to wake it up.
Additionally, we only need to set the state back to TASK_RUNNING if
kthread_should_stop() breaks the loop.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Fixes: d3046ba809ce ("pcmcia: fix a boot time warning in pcmcia cs code") Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de Fixes: 03fd3cf5a179 ("can: add driver for Softing card") Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Locality is not appropriately requested before writing the int mask.
Add the missing boilerplate.
Fixes: e6aef069b6e9 ("tpm_tis: convert to using locality callbacks") Signed-off-by: Chen Jun <chenjun102@huawei.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for meson_spifc_probe.
Fixes: c3e4bc5434d2 ("spi: meson: Add support for Amlogic Meson SPIFC") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220107075424.7774-1-linmq006@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
As the possible failure of the allocation, the devm_ioremap() may return
NULL pointer.
Take tgec_initialization() as an example.
If allocation fails, the params->base_addr will be NULL pointer and will
be assigned to tgec->regs in tgec_config().
Then it will cause the dereference of NULL pointer in set_mac_address(),
which is called by tgec_init().
Therefore, it should be better to add the sanity check after the calling
of the devm_ioremap().
Fixes: 3933961682a3 ("fsl/fman: Add FMan MAC driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the possible alloc failure of devm_kcalloc(), it could return null
pointer.
Therefore, 'strings' should be checked and return NULL if alloc fails to
prevent the dereference of the NULL pointer.
Also, the caller should also deal with the return value of the
gb_generate_enum_strings() and return -ENOMEM if returns NULL.
Moreover, because the memory allocated with devm_kzalloc() will be
freed automatically when the last reference to the device is dropped,
the 'gbe' in gbaudio_tplg_create_enum_kctl() and
gbaudio_tplg_create_enum_ctl() do not need to free manually.
But the 'control' in gbaudio_tplg_create_widget() and
gbaudio_tplg_process_kcontrols() has a specially error handle to
cleanup.
So it should be better to cleanup 'control' when fails.
The issue takes place in one error path of clusterip_tg_check(). When
memcmp() returns nonzero, the function simply returns the error code,
forgetting to decrease the reference count of a clusterip_config
object, which is bumped earlier by clusterip_config_find_get(). This
may incur reference count leak.
Fix this issue by decrementing the refcount of the object in specific
error path.
Fixes: 06aa151ad1fc74 ("netfilter: ipt_CLUSTERIP: check MAC address when duplicate config is set") Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In nonstatic_find_mem_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In __nonstatic_find_io_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There is a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
[linux@dominikbrodowski.net: Fix typo in commit message] Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log