Arnd Bergmann [Wed, 15 Jan 2025 17:51:13 +0000 (18:51 +0100)]
Merge tag 'samsung-dt64-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.14
1. Exynos8895: Add UART nodes, PMU (performance) for the M2 cluster and
I2C controllers in the camera block (HSI2C in CAM0-3).
2. Exynos990: Add Power Management Unit (Samsung block), PMU
(performance) for M5 cluster and two clock controllers.
3. ExynosAutov920: Add watchdog and DMA controllers.
4. Google GS101: Minor fixes for phy and USB. Add USB Type-C.
5. Exynos850-e850-96 board: Drop gap in memory layout.
6. New SoC: Exynos9810.
7. New boards, all mobile phones:
- Exynos9810:
Samsung Galaxy S9 (SM-G960F)
- Exynos990:
Samsung Galaxy S20 FE (SM-G780F)
Samsung Galaxy S20 5G (SM-G980F)
* tag 'samsung-dt64-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (23 commits)
arm64: dts: exynos8895: Add camera hsi2c nodes
arm64: dts: exynos990: Add clock management unit nodes
arm64: dts: exynos: gs101-oriole: add pd-disable and typec-power-opmode
arm64: dts: exynos: gs101-oriole: enable Maxim max77759 TCPCi
arm64: dts: exynos: Add initial support for Samsung Galaxy S9 (SM-G960F)
arm64: dts: exynos: Add Exynos9810 SoC support
arm64: dts: exynos850-e850-96: Specify reserved secure memory explicitly
arm64: dts: exynos990: Add a PMU node for the third cluster
arm64: dts: exynosautov920: Add DMA nodes
arm64: dts: exynos8895: Add a PMU node for the second cluster
dt-bindings: clock: samsung: Add Exynos990 SoC CMU bindings
arm64: dts: exynosautov920: add watchdog DT node
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 (x1slte)
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 5G (x1s)
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 Series boards (x1s-common)
dt-bindings: arm: samsung: samsung-boards: Add bindings for SM-G981B and SM-G980F board
arm64: dts: exynos: gs101: allow stable USB phy Vbus detection
arm64: dts: exynos: gs101: phy region for exynos5-usbdrd is larger
MAINTAINERS: add myself and Tudor as reviewers for Google Tensor SoC
arm64: dts: exynos990: Add pmu and syscon-reboot nodes
...
Artur Weber [Fri, 16 Aug 2024 07:51:02 +0000 (09:51 +0200)]
ARM: dts: samsung: exynos4212-tab3: Drop interrupt from WM1811 codec
This was initially copied from the Midas DTSI, but there is no
proof that the same interrupt is also used on the Tab 3. The pin
listed as the interrupt here is GPIO_HDMI_CEC on the Midas,
but for the Tab 3 it is the headset button GPIO - GPIO_EAR_SEND_END.
Drop the interrupt, since there is no proof that it is used.
In the schematics, the MCLK2 pin is shown as connected to CODEC_CLK32K,
which is derived from the same 32KHZ_PMIC clock as Bluetooth/WiFi and
GPS clocks. 32KHZ_PMIC is connected to the BTCLK pin, represented in
mainline as S2MPS11_CLK_BT.
Add the MCLK2 clock to the WM1811 codec clock property to properly
describe the hardware.
André Draszik [Tue, 3 Dec 2024 12:40:28 +0000 (12:40 +0000)]
arm64: dts: exynos: gs101-oriole: add pd-disable and typec-power-opmode
When the serial console is enabled, we need to disable power delivery
since serial uses the SBU1/2 pins and appears to confuse the TCPCI,
resulting in endless interrupts.
For now, change the DT such that the serial console continues working.
Note1: We can not have both typec-power-opmode and
new-source-frs-typec-current active at the same time, as otherwise DT
binding checks complain.
Note2: When using a downstream DT, the Pixel boot-loader will modify
the DT accordingly before boot, but for this upstream DT it doesn't
know where to find the TCPCI node. The intention is for this commit to
be reverted once an updated Pixel boot-loader becomes available.
On Pixel 6 (and Pro), a max77759 companion PMIC for USB Type-C
applications is used, which contains four functional blocks (at
distinct I2C addresses):
* top (including GPIO)
* charger
* fuel gauge
* TCPCi
While in the same package, TCPCi and Fuel Gauge have separate I2C
addresses, interrupt lines and interrupt status registers and can be
treated independently.
The TCPCi is required to detect and handle connector orientation in
Pixel's USB PHY driver, and to configure the USB controller's role
(host vs device).
This change adds the TCPCi part as it can be independent and doesn't
need a top-level MFD.
Markuss Broks [Sat, 14 Dec 2024 14:56:47 +0000 (16:56 +0200)]
arm64: dts: exynos: Add initial support for Samsung Galaxy S9 (SM-G960F)
Samsung Galaxy S9 (SM-G960F), codenamed starlte, is a mobile phone
released in 2017. It has 4GB of RAM, 64GB of UFS storage, Exynos9810
SoC and 1440x2960 Super AMOLED display.
This initial device tree enables the framebuffer pre-initialised
by bootloader and physical buttons of the device, with more support
to come in the future.
Markuss Broks [Sat, 14 Dec 2024 14:56:46 +0000 (16:56 +0200)]
arm64: dts: exynos: Add Exynos9810 SoC support
Exynos 9810 is an ARMv8 mobile SoC found in various Samsung devices,
such as Samsung Galaxy S9 (starlte), S9 Plus (star2lte),
Note 9 (crownlte) and perhaps others.
Add minimal support for this SoC, including basic stuff like:
- PSCI for bringing up secondary cores
- ARMv8 generic timer
- GPIO and pinctrl.
The firmware coming with the devices based on this SoC is buggy
and doesn't configure CNTFRQ_EL0, as required by spec, so it's
needed to hardcode the frequency in the timer node.
Co-developed-by: Maksym Holovach <nergzd@nergzd723.xyz> Signed-off-by: Maksym Holovach <nergzd@nergzd723.xyz> Signed-off-by: Markuss Broks <markuss.broks@gmail.com> Link: https://lore.kernel.org/r/20241214-exynos9810-v4-1-4e91fbbc2133@gmail.com
[krzysztof: Rename and move PMU nodes to proper sorting position] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Instead of carving out the secure area in 'memory' node, let's describe
it in 'reserved-memory'. That makes it easier to understand both RAM
regions and particular secure world memory region. Originally the device
tree was created in a way to make sure it was well aligned with the way
LittleKernel bootloader modified it. But later it was found the
LittleKernel works fine with properly described reserved regions, so
it's possible now to define those in a cleaner way.
Arnd Bergmann [Fri, 20 Dec 2024 16:45:12 +0000 (17:45 +0100)]
Merge tag 'renesas-dts-for-v6.14-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.14
- Add more serial (SCIF), power monitor, ADC, and sound support for
the RZ/G3S SoC and the RZ/G3S SMARC SoM and development board,
- Add support for the R-Car V4H ES3.0 (R8A779G3) SoC on the White Hawk
Single development board,
- Add display support for the R-Car V4M SoC and the Gray Hawk Single
development board,
- Add video capture support for the Gray Hawk Single development
board,
- Add initial support for the RZ/G3E (R9A09G047) SoC and the RZ/G3E
SMARC SoM and Carrier-II EVK development board,
- Add support for 5-port MATEnet on the Falcon Ethernet sub-board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.14-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (33 commits)
arm64: dts: renesas: r9a09g047: Add I2C nodes
arm64: dts: renesas: rzg3s-smarc: Add sound card
arm64: dts: renesas: rzg3s-smarc: Enable SSI3
arm64: dts: renesas: Add da7212 audio codec node
arm64: dts: renesas: rzg3s-smarc-som: Add versa3 clock generator node
arm64: dts: renesas: r9a08g045: Add SSI nodes
arm64: dts: renesas: rzg3s-smarc-som: Enable ADC
arm64: dts: renesas: r9a08g045: Add ADC node
arm64: dts: renesas: Add initial device tree for RZ/G3E SMARC EVK board
arm64: dts: renesas: Add initial support for RZ/G3E SMARC SoM
arm64: dts: renesas: r9a09g047: Add OPP table
arm64: dts: renesas: Add initial DTSI for RZ/G3E SoC
arm64: dts: renesas: falcon-ethernet: Describe PHYs connected on the breakout board
arm64: dts: renesas: r8a779a0: Remove address- and size-cells from AVB[1-5]
dt-bindings: clock: renesas: Document RZ/G3E SoC CPG
dt-bindings: soc: renesas: Document RZ/G3E SMARC SoM and Carrier-II EVK
dt-bindings: soc: renesas: Document Renesas RZ/G3E SoC variants
arm64: dts: renesas: gray-hawk-single: Add video capture support
arm64: dts: renesas: gray-hawk-single: Add DisplayPort support
arm64: dts: renesas: r8a779h0: Add display support
...
Arnd Bergmann [Fri, 20 Dec 2024 16:40:06 +0000 (17:40 +0100)]
Merge tag 'stm32-dt-for-v6.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.14, round 1
Highlights:
----------
- MPU:
- STM32MP13:
- Populate all timer counter nodes in Soc file.
- Enable counter (timers) on stm32mp135f-dk.
- DH core: increase CPU voltage to fit with STM32MP135F datasheet.
- STMP32MP15:
- Populate all timer counter nodes in Soc file.
- Enable counter (timers) on stm32mp15 EV1 and DK boards.
- OCTAVO:
- LXA-TAC (gen1/2): disable RTC, update aliases and
adjust USB gadget.
- Add LXA-TAC gen3 based on OSD32MP153x SIP:
STMP32MP153, RAM, PMIC.
- DH: minor fixes.
- STM32MP25:
- Enable imx335/CSI/DCMIPP pipeline on stm32mp257f-ev1.
- Add I2S, SAI, SPDIFRX supports.
- Add and enable COMBOPHY on stm32mp257f-ev1. Combophy is used
by PCIe and USB3.
* tag 'stm32-dt-for-v6.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (23 commits)
arm64: dts: st: enable imx335/csi/dcmipp pipeline on stm32mp257f-ev1
arm64: dts: st: add csi & dcmipp node in stm32mp25
ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM
ARM: dts: stm32: add counter subnodes on stm32mp157 dk boards
ARM: dts: stm32: add counter subnodes on stm32mp157c-ev1
ARM: dts: stm32: add counter subnodes on stm32mp135f-dk
ARM: dts: stm32: populate all timer counter nodes on stm32mp15
ARM: dts: stm32: populate all timer counter nodes on stm32mp13
ARM: dts: stm32: lxa-tac: Add support for generation 3 devices
ARM: dts: stm32: lxa-tac: move adc and gpio{e,g} to gen{1,2} boards
dt-bindings: arm: stm32: add compatible strings for Linux Automation LXA TAC gen 3
ARM: dts: stm32: lxa-tac: adjust USB gadget fifo sizes for multi function
ARM: dts: stm32: lxa-tac: extend the alias table
ARM: dts: stm32: lxa-tac: disable the real time clock
ARM: dts: stm32: Fix IPCC EXTI declaration on stm32mp151
ARM: dts: stm32: Sort M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT
ARM: dts: stm32: Increase CPU core voltage on STM32MP13xx DHCOR SoM
ARM: dts: stm32: Deduplicate serial aliases and chosen node for STM32MP15xx DHCOM SoM
arm64: dts: st: Enable COMBOPHY on the stm32mp257f-ev1 board
arm64: dts: st: Add combophy node on stm32mp251
...
Marek Vasut [Fri, 13 Dec 2024 22:36:25 +0000 (23:36 +0100)]
ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabrice Gasnier [Mon, 16 Dec 2024 15:39:05 +0000 (16:39 +0100)]
ARM: dts: stm32: populate all timer counter nodes on stm32mp15
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
Fabrice Gasnier [Mon, 16 Dec 2024 15:39:04 +0000 (16:39 +0100)]
ARM: dts: stm32: populate all timer counter nodes on stm32mp13
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
Faraz Ata [Thu, 12 Dec 2024 11:57:05 +0000 (17:27 +0530)]
arm64: dts: exynosautov920: Add DMA nodes
ExynosAutov920 SoC has 7 DMA controllers. Two secure DMAC
(SPDMA0 & SPDMA1) and five non-secure DMAC (PDMA0 to PDMA4).
Add the required dt nodes for the same.
Add dt-schema documentation for the Exynos990 SoC CMU.
This clock management unit has a topmost block (CMU_TOP)
that generates top clocks for other blocks. Currently the
only other block implemented is CMU_HSI0, which provides
clocks for the USB part of the SoC.
Also, device-tree binding definitions added for these blocks:
- CMU_TOP
- CMU_HSI0
Claudiu Beznea [Tue, 10 Dec 2024 17:09:49 +0000 (19:09 +0200)]
arm64: dts: renesas: r9a08g045: Add SSI nodes
Add DT nodes for the SSI IPs available on the Renesas RZ/G3S SoC. Along
with it external audio clocks were added. Board device tree could use it
and update the frequencies.
Biju Das [Tue, 3 Dec 2024 10:49:36 +0000 (10:49 +0000)]
arm64: dts: renesas: Add initial DTSI for RZ/G3E SoC
Add the initial DTSI for the RZ/G3E SoC.
The files in this commit have the following meaning:
- r9a09g047.dtsi: RZ/G3E family SoC common parts
- r9a09g047e57.dtsi: RZ/G3E R0A09G047E{4,5}{7,8} SoC specific parts
- r9a09g047e37.dtsi: RZ/G3E R0A09G047E{2,3}{7,8} SoC specific parts
Niklas Söderlund [Wed, 23 Oct 2024 15:46:42 +0000 (17:46 +0200)]
arm64: dts: renesas: r8a779a0: Remove address- and size-cells from AVB[1-5]
When describing the PHYs on the Falcon Ethernet breakout board mdio
nodes will be needed to describe the connections, and each mdio node
will need to contain these two properties instead. This will make the
address-cells and size-cells described in the base SoC include file
redundant and they will produce warnings, remove them.
Biju Das [Tue, 3 Dec 2024 10:49:30 +0000 (10:49 +0000)]
dt-bindings: soc: renesas: Document RZ/G3E SMARC SoM and Carrier-II EVK
Document the Renesas RZ/G3E SMARC Carrier-II EVK board which is based
on the Renesas RZ/G3E SMARC SoM. The RZ/G3E SMARC Carrier-II EVK
consists of an RZ/G3E SoM module and a SMARC Carrier-II carrier board.
The SoM module sits on top of the carrier board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Acked-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20241203105005.103927-4-biju.das.jz@bp.renesas.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Niklas Söderlund [Mon, 9 Dec 2024 12:55:04 +0000 (13:55 +0100)]
arm64: dts: renesas: gray-hawk-single: Add video capture support
The Gray-Hawk single board contains two MAX96724 connected to the using
I2C and CSI-2, record the connections. Also enable all nodes (VIN, CSI-2
and ISP) that are part of the downstream video capture pipeline.
Geert Uytterhoeven [Thu, 5 Dec 2024 12:53:49 +0000 (13:53 +0100)]
arm64: dts: renesas: white-hawk-single: Add R-Car Sound support
White Hawk Single boards can use the same ARD-AUDIO-DA7212 external
audio board as the White Hawk board stack. Add support for building
DTBs for them, and document the small differences in connector labels.
Geert Uytterhoeven [Thu, 5 Dec 2024 12:53:48 +0000 (13:53 +0100)]
arm64: dts: renesas: white-hawk-ard-audio: Drop SoC part
The White Hawk with ARD-AUDIO-DA7212 external audio board stack is not
specific to R8A779G0. Hence rename its DTS file name to drop the
"r8a779g0-" prefix.
Claudiu Beznea [Fri, 15 Nov 2024 13:43:58 +0000 (15:43 +0200)]
arm64: dts: renesas: rzg3s-smarc: Fix the debug serial alias
The debug serial of the RZ/G3S is SCIF0 which is routed on the Renesas
RZ SMARC Carrier II board on the SER3_UART. Use serial3 alias for it for
better hardware description. Along with it, the chosen properties were
moved to the device tree corresponding to the RZ SMARC Carrier II board.
Fixes: adb4f0c5699c ("arm64: dts: renesas: Add initial support for RZ/G3S SMARC SoM") Fixes: d1ae4200bb26 ("arm64: dts: renesas: Add initial device tree for RZ SMARC Carrier-II Board") Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20241115134401.3893008-6-claudiu.beznea.uj@bp.renesas.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Leonard Göhrs [Tue, 19 Nov 2024 11:34:59 +0000 (12:34 +0100)]
ARM: dts: stm32: lxa-tac: extend the alias table
Some of the userspace software and tests depend on the can/i2c/spi
devices having the same name on every boot. This may not always be the
case based on e.g. parallel probe order.
Assign static device numbers to all can/i2c/spi devices.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Arnaud Pouliquen [Fri, 6 Dec 2024 17:17:59 +0000 (18:17 +0100)]
ARM: dts: stm32: Fix IPCC EXTI declaration on stm32mp151
The GIC IRQ type used for IPCC RX should be IRQ_TYPE_LEVEL_HIGH.
Replacing the interrupt with the EXTI event changes the type to
the numeric value 1, meaning IRQ_TYPE_EDGE_RISING.
The issue is that EXTI event 61 is a direct event.The IRQ type of
direct events is not used by EXTI and is propagated to the parent
IRQ controller of EXTI, the GIC.
Align the IRQ type to the value expected by the GIC by replacing
the second parameter "1" with IRQ_TYPE_LEVEL_HIGH.
Fixes: 7d9802bb0e34 ("ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151") Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Umer Uddin [Mon, 9 Dec 2024 08:00:59 +0000 (08:00 +0000)]
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 (x1slte)
Add initial support for the Samsung Galaxy S20 (x1slte/SM-G980F)
phone. It was launched in 2020, and it's based on the Exynos 990 SoC. It
has only one configuration with 8GB of RAM and 128GB of UFS 3.0 storage.
Umer Uddin [Mon, 9 Dec 2024 08:00:58 +0000 (08:00 +0000)]
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 5G (x1s)
Add initial support for the Samsung Galaxy S20 5G (x1s/SM-G981B)
phone. It was launched in 2020, and it's based on the Exynos 990 SoC. It
has only one configuration with 12GB of RAM and 128GB of UFS 3.0 storage.
Umer Uddin [Mon, 9 Dec 2024 08:00:57 +0000 (08:00 +0000)]
arm64: dts: exynos: Add initial support for Samsung Galaxy S20 Series boards (x1s-common)
Add initial support for the Samsung Galaxy S20 Series (x1s-common) phones.
They were launched in 2020, and are based on the Exynos 990 SoC.
The devices have multiple RAM configurations,
starting from 8GB going all the way up to 16GB for the S20 Ultra devices.
This device tree adds support for the following:
- SimpleFB
- 8GB RAM (Any more will be mapped in device trees)
- Buttons
André Draszik [Tue, 3 Dec 2024 12:40:26 +0000 (12:40 +0000)]
arm64: dts: exynos: gs101: allow stable USB phy Vbus detection
For the DWC3 core to reliably detect the connected phy's Vbus state, we
need to disable phy suspend.
Add
snps,dis_u2_susphy_quirk
snps,dis_u3_susphy_quirk
to do that.
While at it, also add
snps,has-lpm-erratum
as this is set downstream which implies that the core was configured
with LPM Erratum. We should do the same here.
Marek Vasut [Tue, 5 Nov 2024 23:40:41 +0000 (00:40 +0100)]
ARM: dts: stm32: Sort M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT
Move the M24256E write-lockable page subnode after RTC subnode in
DH STM32MP13xx DHCOR SoM DT to keep the list of nodes sorted by I2C
address. No functional change.
Fixes: 3f2e7d167307 ("ARM: dts: stm32: Describe M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 5 Nov 2024 22:46:22 +0000 (23:46 +0100)]
ARM: dts: stm32: Increase CPU core voltage on STM32MP13xx DHCOR SoM
The STM32MP13xx DHCOR DHSBC is populated with STM32MP13xx part capable
of 1 GHz operation, increase the CPU core voltage to 1.35 V to make
sure the SoC is stable even if the blobs unconditionally force the CPU
to 1 GHz operation.
It is not possible to make use of CPUfreq on the STM32MP13xx because
the SCMI protocol 0x13 is not implemented by upstream OpTee-OS which
is the SCMI provider.
Fixes: 6331bddce649 ("ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 5 Nov 2024 23:29:44 +0000 (00:29 +0100)]
ARM: dts: stm32: Deduplicate serial aliases and chosen node for STM32MP15xx DHCOM SoM
Deduplicate /aliases { serialN = ... } and /chosen node into
stm32mp15xx-dhcom-som.dtsi , since the content is identical
on all carrier boards using the STM32MP15xx DHCOM SoM. No
functional change.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Christian Bruel [Mon, 30 Sep 2024 17:08:46 +0000 (19:08 +0200)]
arm64: dts: st: Add combophy node on stm32mp251
Add support for COMBOPHY which is used either by the USB3 and PCIe
controller.
USB3 or PCIe mode is done with phy_set_mode().
PCIe internal reference clock can be generated from the internal clock
source or optionnaly from an external 100Mhz pad.
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Linus Torvalds [Sun, 8 Dec 2024 20:01:06 +0000 (12:01 -0800)]
Merge tag 'kbuild-fixes-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix a section mismatch warning in modpost
- Fix Debian package build error with the O= option
* tag 'kbuild-fixes-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: deb-pkg: fix build error with O=
modpost: Add .irqentry.text to OTHER_SECTIONS
Linus Torvalds [Sun, 8 Dec 2024 19:54:04 +0000 (11:54 -0800)]
Merge tag 'irq_urgent_for_v6.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Fix a /proc/interrupts formatting regression
- Have the BCM2836 interrupt controller enter power management states
properly
- Other fixlets
* tag 'irq_urgent_for_v6.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/stm32mp-exti: CONFIG_STM32MP_EXTI should not default to y when compile-testing
genirq/proc: Add missing space separator back
irqchip/bcm2836: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
irqchip/gic-v3: Fix irq_complete_ack() comment
Linus Torvalds [Sun, 8 Dec 2024 19:51:29 +0000 (11:51 -0800)]
Merge tag 'timers_urgent_for_v6.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Handle the case where clocksources with small counter width can,
in conjunction with overly long idle sleeps, falsely trigger the
negative motion detection of clocksources
* tag 'timers_urgent_for_v6.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Make negative motion detection more robust
Linus Torvalds [Sun, 8 Dec 2024 19:38:56 +0000 (11:38 -0800)]
Merge tag 'x86_urgent_for_v6.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Have the Automatic IBRS setting check on AMD does not falsely fire in
the guest when it has been set already on the host
- Make sure cacheinfo structures memory is allocated to address a boot
NULL ptr dereference on Intel Meteor Lake which has different numbers
of subleafs in its CPUID(4) leaf
- Take care of the GDT restoring on the kexec path too, as expected by
the kernel
- Make sure SMP is not disabled when IO-APIC is disabled on the kernel
cmdline
- Add a PGD flag _PAGE_NOPTISHADOW to instruct machinery not to
propagate changes to the kernelmode page tables, to the user portion,
in PTI
- Mark Intel Lunar Lake as affected by an issue where MONITOR wakeups
can get lost and thus user-visible delays happen
- Make sure PKRU is properly restored with XRSTOR on AMD after a PRKU
write of 0 (WRPKRU) which will mark PKRU in its init state and thus
lose the actual buffer
* tag 'x86_urgent_for_v6.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: WARN when setting EFER.AUTOIBRS if and only if the WRMSR fails
x86/cacheinfo: Delete global num_cache_leaves
cacheinfo: Allocate memory during CPU hotplug if not done from the primary CPU
x86/kexec: Restore GDT on return from ::preserve_context kexec
x86/cpu/topology: Remove limit of CPUs due to disabled IO/APIC
x86/mm: Add _PAGE_NOPTISHADOW bit to avoid updating userspace page tables
x86/cpu: Add Lunar Lake to list of CPUs with a broken MONITOR implementation
x86/pkeys: Ensure updated PKRU value is XRSTOR'd
x86/pkeys: Change caller of update_pkru_in_sigframe()
Linus Torvalds [Sun, 8 Dec 2024 19:26:13 +0000 (11:26 -0800)]
Merge tag 'mm-hotfixes-stable-2024-12-07-22-39' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"24 hotfixes. 17 are cc:stable. 15 are MM and 9 are non-MM.
The usual bunch of singletons - please see the relevant changelogs for
details"
* tag 'mm-hotfixes-stable-2024-12-07-22-39' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (24 commits)
iio: magnetometer: yas530: use signed integer type for clamp limits
sched/numa: fix memory leak due to the overwritten vma->numab_state
mm/damon: fix order of arguments in damos_before_apply tracepoint
lib: stackinit: hide never-taken branch from compiler
mm/filemap: don't call folio_test_locked() without a reference in next_uptodate_folio()
scatterlist: fix incorrect func name in kernel-doc
mm: correct typo in MMAP_STATE() macro
mm: respect mmap hint address when aligning for THP
mm: memcg: declare do_memsw_account inline
mm/codetag: swap tags when migrate pages
ocfs2: update seq_file index in ocfs2_dlm_seq_next
stackdepot: fix stack_depot_save_flags() in NMI context
mm: open-code page_folio() in dump_page()
mm: open-code PageTail in folio_flags() and const_folio_flags()
mm: fix vrealloc()'s KASAN poisoning logic
Revert "readahead: properly shorten readahead when falling back to do_page_cache_ra()"
selftests/damon: add _damon_sysfs.py to TEST_FILES
selftest: hugetlb_dio: fix test naming
ocfs2: free inode when ocfs2_get_init_inode() fails
nilfs2: fix potential out-of-bounds memory access in nilfs_find_entry()
...
Masahiro Yamada [Sun, 8 Dec 2024 07:56:45 +0000 (16:56 +0900)]
kbuild: deb-pkg: fix build error with O=
Since commit 13b25489b6f8 ("kbuild: change working directory to external
module directory with M="), the Debian package build fails if a relative
path is specified with the O= option.
$ make O=build bindeb-pkg
[ snip ]
dpkg-deb: building package 'linux-image-6.13.0-rc1' in '../linux-image-6.13.0-rc1_6.13.0-rc1-6_amd64.deb'.
Rebuilding host programs with x86_64-linux-gnu-gcc...
make[6]: Entering directory '/home/masahiro/linux/build'
/home/masahiro/linux/Makefile:190: *** specified kernel directory "build" does not exist. Stop.
This occurs because the sub_make_done flag is cleared, even though the
working directory is already in the output directory.
Passing KBUILD_OUTPUT=. resolves the issue.
Fixes: 13b25489b6f8 ("kbuild: change working directory to external module directory with M=") Reported-by: Charlie Jenkins <charlie@rivosinc.com> Closes: https://lore.kernel.org/all/Z1DnP-GJcfseyrM3@ghost/ Tested-by: Charlie Jenkins <charlie@rivosinc.com> Reviewed-by: Charlie Jenkins <charlie@rivosinc.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Thomas Gleixner [Sun, 1 Dec 2024 11:17:30 +0000 (12:17 +0100)]
modpost: Add .irqentry.text to OTHER_SECTIONS
The compiler can fully inline the actual handler function of an interrupt
entry into the .irqentry.text entry point. If such a function contains an
access which has an exception table entry, modpost complains about a
section mismatch:
WARNING: vmlinux.o(__ex_table+0x447c): Section mismatch in reference ...
The relocation at __ex_table+0x447c references section ".irqentry.text"
which is not in the list of authorized sections.
Add .irqentry.text to OTHER_SECTIONS to cure the issue.
Reported-by: Sergey Senozhatsky <senozhatsky@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org # needed for linux-5.4-y Link: https://lore.kernel.org/all/20241128111844.GE10431@google.com/ Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Linus Torvalds [Sun, 8 Dec 2024 01:27:25 +0000 (17:27 -0800)]
Merge tag '6.13-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- DFS fix (for race with tree disconnect and dfs cache worker)
- Four fixes for SMB3.1.1 posix extensions:
- improve special file support e.g. to Samba, retrieving the file
type earlier
- reduce roundtrips (e.g. on ls -l, in some cases)
* tag '6.13-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: fix potential race in cifs_put_tcon()
smb3.1.1: fix posix mounts to older servers
fs/smb/client: cifs_prime_dcache() for SMB3 POSIX reparse points
fs/smb/client: Implement new SMB3 POSIX type
fs/smb/client: avoid querying SMB2_OP_QUERY_WSL_EA for SMB3 POSIX
Linus Torvalds [Sun, 8 Dec 2024 01:17:38 +0000 (17:17 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Large number of small fixes, all in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: scsi_debug: Fix hrtimer support for ndelay
scsi: storvsc: Do not flag MAINTENANCE_IN return of SRB_STATUS_DATA_OVERRUN as an error
scsi: ufs: core: Add missing post notify for power mode change
scsi: sg: Fix slab-use-after-free read in sg_release()
scsi: ufs: core: sysfs: Prevent div by zero
scsi: qla2xxx: Update version to 10.02.09.400-k
scsi: qla2xxx: Supported speed displayed incorrectly for VPorts
scsi: qla2xxx: Fix NVMe and NPIV connect issue
scsi: qla2xxx: Remove check req_sg_cnt should be equal to rsp_sg_cnt
scsi: qla2xxx: Fix use after free on unload
scsi: qla2xxx: Fix abort in bsg timeout
scsi: mpi3mr: Update driver version to 8.12.0.3.50
scsi: mpi3mr: Handling of fault code for insufficient power
scsi: mpi3mr: Start controller indexing from 0
scsi: mpi3mr: Fix corrupt config pages PHY state is switched in sysfs
scsi: mpi3mr: Synchronize access to ioctl data buffer
scsi: mpt3sas: Update driver version to 51.100.00.00
scsi: mpt3sas: Diag-Reset when Doorbell-In-Use bit is set during driver load time
scsi: ufs: pltfrm: Dellocate HBA during ufshcd_pltfrm_remove()
scsi: ufs: pltfrm: Drop PM runtime reference count after ufshcd_remove()
...
Linus Torvalds [Sat, 7 Dec 2024 18:07:05 +0000 (10:07 -0800)]
Merge tag 'block-6.13-20241207' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Target fix using incorrect zero buffer (Nilay)
- Device specifc deallocate quirk fixes (Christoph, Keith)
- Fabrics fix for handling max command target bugs (Maurizio)
- Cocci fix usage for kzalloc (Yu-Chen)
- DMA size fix for host memory buffer feature (Christoph)
- Fabrics queue cleanup fixes (Chunguang)
- CPU hotplug ordering fixes
- Add missing MODULE_DESCRIPTION for rnull
- bcache error value fix
- virtio-blk queue freeze fix
* tag 'block-6.13-20241207' of git://git.kernel.dk/linux:
blk-mq: move cpuhp callback registering out of q->sysfs_lock
blk-mq: register cpuhp callback after hctx is added to xarray table
virtio-blk: don't keep queue frozen during system suspend
nvme-tcp: simplify nvme_tcp_teardown_io_queues()
nvme-tcp: no need to quiesce admin_q in nvme_tcp_teardown_io_queues()
nvme-rdma: unquiesce admin_q before destroy it
nvme-tcp: fix the memleak while create new ctrl failed
nvme-pci: don't use dma_alloc_noncontiguous with 0 merge boundary
nvmet: replace kmalloc + memset with kzalloc for data allocation
nvme-fabrics: handle zero MAXCMD without closing the connection
bcache: revert replacing IS_ERR_OR_NULL with IS_ERR again
nvme-pci: remove two deallocate zeroes quirks
block: rnull: add missing MODULE_DESCRIPTION
nvme: don't apply NVME_QUIRK_DEALLOCATE_ZEROES when DSM is not supported
nvmet: use kzalloc instead of ZERO_PAGE in nvme_execute_identify_ns_nvm()
projects / users / jedix / linux-maple.git / log