Arnd Bergmann [Tue, 22 Nov 2022 22:00:52 +0000 (23:00 +0100)]
Merge tag 'tegra-for-6.2-dt-bindings-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
dt-bindings: Changes for v6.2-rc1
New memory client IDs and IOMMU stream IDs, as well as new compatible
strings are introduced to support more hardware on Tegra234. Some device
tree bindings are converted to json-schema to allow formal validation.
* tag 'tegra-for-6.2-dt-bindings-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: usb: tegra-xusb: Convert to json-schema
dt-bindings: pwm: tegra: Convert to json-schema
dt-bindings: pinctrl: tegra194: Separate instances
dt-bindings: pinctrl: tegra: Convert to json-schema
dt-bindings: PCI: tegra234: Add ECAM support
dt-bindings: pwm: tegra: Document Tegra234 PWM
dt-bindings: Add bindings for Tegra234 NVDEC
dt-bindings: tegra: Update headers for Tegra234
dt-bindings: Add headers for NVDEC on Tegra234
Arnd Bergmann [Tue, 22 Nov 2022 22:00:03 +0000 (23:00 +0100)]
Merge tag 'socfpga_dts_updates_for_v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into soc/dt
SoCFPGA dts updates for v6.2
- Use the "clk-phase-sd-hs" property for SDMMC
- Remove the "clk-phase" fom the sdmmc_clk that is no longer used
- Clean dtschema for mmc node
- Increase NAND partition for Arria10
* tag 'socfpga_dts_updates_for_v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: socfpga: Add clk-phase-sd-hs property to the sdmmc node
arm: dts: socfpga: Add clk-phase-sd-hs property to the sdmmc node
arm: dts: socfpga: remove "clk-phase" in sdmmc_clk
arm: dts: socfpga: align mmc node names with dtschema
ARM: dts: socfpga: arria10: Increase NAND boot partition size
Arnd Bergmann [Tue, 22 Nov 2022 21:57:53 +0000 (22:57 +0100)]
Merge tag 'riscv-dt-for-v6.2-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V DeviceTrees for v6.2
dt-bindings:
- new compatibles to support the StarFive VisionFive & thead CPU cores
- a fix for the PolarFire SoC's pwm binding, merged through my tree as
suggested by the PWM maintainers
Microchip:
- Non-urgent fix for the node address not matches the reg in a way that
the checkers don't complain about
- Add GPIO controlled LEDs for Icicle
- Support for the "CCC" clocks in the FPGA fabric. Previously these
used fixed-frequency clocks in the dt, but if which CCC is in use is
known, as in the v2022.09 Icicle Kit Reference Design, the rates can
be read dynamically. It's an "is known" as it *can* be set via
constraints in the FPGA tooling but does not have to be.
- A fix for the Icicle's pwm-cells
- Removal of some unused PCI clocks
StarFive:
- Addition of the VisionFive DT, which has been a long time coming!
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.2-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
dt-bindings: riscv: Add T-HEAD C906 and C910 compatibles
riscv: dts: microchip: remove unused pcie clocks
riscv: dts: microchip: remove pcie node from the sev kit
riscv: dts: microchip: fix the icicle's #pwm-cells
dt-bindings: pwm: fix microchip corePWM's pwm-cells
riscv: dts: starfive: Add StarFive VisionFive V1 device tree
riscv: dts: starfive: Add common DT for JH7100 based boards
dt-bindings: riscv: starfive: Add StarFive VisionFive V1 board
riscv: dts: microchip: fix memory node unit address for icicle
riscv: dts: microchip: icicle: Add GPIO controlled LEDs
riscv: dts: microchip: add the mpfs' fabric clock control
Sam Shih [Fri, 18 Nov 2022 19:01:21 +0000 (20:01 +0100)]
arm64: dts: mt7986: add spi related device nodes
This patch adds spi support for MT7986.
Signed-off-by: Sam Shih <sam.shih@mediatek.com> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20221118190126.100895-7-linux@fw-web.de Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Arnd Bergmann [Mon, 21 Nov 2022 10:56:08 +0000 (11:56 +0100)]
Merge tag 'renesas-arm-dt-for-v6.2-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas ARM DT updates for v6.2 (take two)
- Timer (TMU and CMT) and quad Cortex-A76 CPU topology support for
the R-Car V4H SoC,
- Watchdog, L2 cache, and system controller support for the RZ/V2M
SoC on the RZ/V2M Evaluation Kit 2.0,
- Ethernet Switch and SERDES supports for the R-Car S4-8 SoC and the
Spider development board,
- Miscellaneous fixes and improvements.
Arnd Bergmann [Mon, 21 Nov 2022 10:53:09 +0000 (11:53 +0100)]
Merge tag 'renesas-dt-bindings-for-v6.2-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DT binding updates for v6.2 (take two)
- Document support for the Andes Technology AX45MP RISC-V CPU Core, as
used on the Renesas RZ/Five SoC,
- Document support for the Renesas RZ/V2M System Configuration.
* tag 'renesas-dt-bindings-for-v6.2-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Document Renesas RZ/V2M System Configuration
dt-bindings: riscv: Add Andes AX45MP core to the list
dt-bindings: riscv: Sort the CPU core list alphabetically
Arnd Bergmann [Mon, 21 Nov 2022 10:44:13 +0000 (11:44 +0100)]
Merge tag 'stm32-dt-for-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.2, round 1
Highlights:
----------
- MPU:
- ST boards:
- Add MCP23017 IO expander support on stm32mp135f-dk board.
- Add stm32g0 support for USB typeC on stm32mp135f-dk
- Add USB (EHCI / OTG) on stm32mp135f-dk
- Add ADC support on stm32mp135f-dk
- Add USB2514B onboard hub on stm32mp157c-ev1
- DH:
- Fix severals Yaml DT validation issues
* tag 'stm32-dt-for-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (28 commits)
ARM: dts: stm32: Rename mdio0 to mdio on DHCOR Testbench board
ARM: dts: stm32: add mcp23017 IO expander on I2C1 on stm32mp135f-dk
ARM: dts: stm32: add mcp23017 pinctrl entry for stm32mp13
ARM: dts: stm32: enable USB OTG in dual role mode on stm32mp135f-dk
ARM: dts: stm32: add pins for stm32g0 typec controller on stm32mp13
ARM: dts: stm32: enable USB Host EHCI on stm32mp135f-dk
ARM: dts: stm32: enable USB HS phys on stm32mp135f-dk
ARM: dts: stm32: add fixed regulators to support usb on stm32mp135f-dk
ARM: dts: stm32: add USB OTG HS support on stm32mp131
ARM: dts: stm32: add UBSH EHCI and OHCI support on stm32mp131
ARM: dts: stm32: add USBPHYC and dual USB HS PHY support on stm32mp131
ARM: dts: stm32: add PWR fixed regulators on stm32mp131
ARM: dts: stm32: Fix AV96 WLAN regulator gpio property
ARM: dts: stm32: add adc support on stm32mp135f-dk
ARM: dts: stm32: add dummy vdd_adc regulator on stm32mp135f-dk
ARM: dts: stm32: add adc pins muxing on stm32mp135f-dk
ARM: dts: stm32: add adc support to stm32mp13
ARM: dts: stm32: Drop MMCI interrupt-names
ARM: dts: stm32: update vbus-supply of usbphyc_port0 on stm32mp157c-ev1
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp157c-ev1
...
Arnd Bergmann [Mon, 21 Nov 2022 10:40:29 +0000 (11:40 +0100)]
Merge tag 'imx-dt64-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX arm64 device tree update for 6.2:
- New device trees for i.MX8MM based Cloos PHG and WB15 SoM/EVK.
- A set of tqma8mpql/mba8mpxl changes, adding USB Host, PCIe, PWM fan
support.
- Rename DTB overlay source files from .dts to .dtso.
- A series from Frank Li to add USB, ADC, FlexSPI, LPSPI support for
i.MX8DXL.
- A couple of librem5-devkit changes, switching LED to use PWM and using
function and color properties for LED.
- Enable wakeup-source for USB PHY for i.MX8MM/N EVK.
- A set of random changes from Marcel Ziswiler to improve i.MX8M based
Verdin device trees.
- A series from Marek Vasut to update Data Modul i.MX8M Mini eDM SBC and
DH electronics i.MX8M Plus DHCOM, modeling PMIC to SNVS RTC clock
path, dropping QCA clk_out setup, adding bluetooth UART, etc.
- A bunch of changes from Peng Fan to add LPSPI, TPM etc for i.MX93,
update i.MX8MP/N EVK with UART, I2C addition.
- Update cache properties per DeviceTree Specification v0.3.
- Add gpio-ranges property for i.MX8DXL and i.MX8Q LSIO Subsystem.
- Misc small and random changes.
* tag 'imx-dt64-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (60 commits)
arm64: dts: freescale: Rename DTB overlay source files from .dts to .dtso
arm64: dts: imx8mm-evk: add vcc supply for pca6416
arm64: dts: imx8m[m,q]-evk: change to use off-on-delay-us in regulator
arm64: dts: imx8mn-evk: enable uart1
arm64: dts: imx8mn-evk: add i2c gpio recovery settings
arm64: dts: imx8mn-evk: set off-on-delay-us in regulator
arm64: dts: imx8mn-evk: update vdd_soc dvs voltage
arm64: dts: imx8mp-evk: enable I2C2 node
arm64: dts: imx8mp-evk: enable fspi nor on imx8mp evk
arm64: dts: imx8mp-evk: enable uart1/3 ports
ARM64: dts: imx8mp-evk: add pwm support
arm64: dts: imx8mp: add mlmix power domain
arm64: dts: imx8mq: fix dtschema warning for imx7-csi
arm64: dts: Update cache properties for freescale
arm64: dts: imx8mm-phg: Add initial board support
arm64: dts: imx8qxp-ss-lsio: add gpio-ranges property
arm64: dts: imx8qm-ss-lsio: add gpio-ranges property
arm64: dts: imx8dxl-ss-lsio: add gpio-ranges property
arm64: dts: imx8dxl_evk: add lpspi0 support
arm64: dts: imx8dxl: add lpspi support
...
Arnd Bergmann [Mon, 21 Nov 2022 10:08:01 +0000 (11:08 +0100)]
Merge tag 'imx-dt-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX arm device tree update for 6.2:
- New device tree for Kobo Aura 2 E-Boot reader which is built on i.MX6SL
SoC.
- Enable backlight and boost support for imx6sl-tolino-shine2hd.
- Enable CYTTSP5 touchscreen support for E60K02.
- Enable Silergy SY7636A EPD PMIC on imx7d-remarkable2 epaper tablet.
- Add watchdog property 'fsl,suspend-in-wait' for i.MX6UL Phytec Phycore
SoM to avoid watchdog triggering in 'freeze' low power mode.
- Correct the polarity of AT86RF233 reset line for vf610-zii-dev-rev-c
board.
- A bunch of Colibri device tree updates from Marcel Ziswiler and Philippe
Schenker, correct USBH_PEN property, remove spurious debounce property,
add USB dual-role switching, and some cosmetic change.
- Other small and random changes.
Arnd Bergmann [Mon, 21 Nov 2022 10:06:42 +0000 (11:06 +0100)]
Merge tag 'imx-bindings-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX dt-bindings update for 6.2:
- New vendor prefix for Cloos and InnoComm.
- New compatible for Cloos PHG board, InnoComm WB15 EVK and Kobo Aura 2.
- Improve snvs-lpgpr bindings schema regarding i.MX8M SNVS LPGRP
compatible strings.
- Improve fsl-imx-cspi bindings schema for i.MX8MP ECSPI.
- Add bindings schema for i.MX8M ANATOP device.
- Update SCU firmware resource ID header by syncing with the latest
available SCFW kit version 1.13.0.
* tag 'imx-bindings-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: Add an entry for Cloos PHG board
dt-bindings: vendor-prefixes: Add an entry for Cloos
dt-bindings: nvmem: snvs-lpgpr: Fix i.MX8M compatible strings
dt-bindings: spi: fsl-imx-cspi: update i.MX8MP binding
dt-bindings: arm: fsl: add compatible string for Kobo Aura 2
dt-bindings: clock: add i.MX8M Anatop
dt-bindings: arm: fsl: Add InnoComm WB15 EVK
dt-bindings: vendor-prefixes: Add prefix for InnoComm
dt-bindings: firmware: imx: sync with SCFW kit v1.13.0
Thierry Reding [Fri, 4 Nov 2022 12:38:34 +0000 (13:38 +0100)]
arm64: tegra: Fix up compatible string for SDMMC1 on Tegra234
The compatible string list for SDHCI on Tegra234 should be
"nvidia,tegra234-sdhci", followed by the "nvidia,tegra186-sdhci"
fallback. Use that consistently for all SDHCI controllers.
The Tegra QSPI controllers use a single reset control, so reset-names is
not necessary and therefore not specified in the DT bindings. Drop the
property from device tree files to avoid validation warnings.
Pierre Gondois [Mon, 7 Nov 2022 15:57:08 +0000 (16:57 +0100)]
arm64: tegra: Update cache properties
The DeviceTree Specification v0.3 specifies that the cache node
'compatible' and 'cache-level' properties are 'required'. Cf.
s3.8 Multi-level and Shared Cache Nodes
The 'cache-unified' property should be present if one of the
properties for unified cache is present ('cache-size', ...).
Update the Device Trees accordingly.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Akhil R [Thu, 10 Nov 2022 17:17:47 +0000 (22:47 +0530)]
arm64: tegra: Add dma-channel-mask in GPCDMA node
Add dma-channel-mask property in Tegra GPCDMA device tree node.
The property would help to specify the channels to be used in
kernel and reserve few for the firmware. This was previously
achieved by limiting the channel number to 31 in the driver.
This is wrong and does not align with the hardware. Correct this
and update the interrupts property to list all 32 interrupts.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 3 Nov 2022 11:35:48 +0000 (12:35 +0100)]
arm64: tegra: Add missing compatible string to Ethernet USB device
According to the DT schema in usb-device.yaml, each USB device node
needs a compatible string, so add one for the built-in USB Ethernet
device on Jetson TX1.
Thierry Reding [Fri, 4 Nov 2022 14:23:45 +0000 (15:23 +0100)]
arm64: tegra: Separate AON pinmux from main pinmux on Tegra194
The registers for the AON pinmux reside in a partition different from
the registers for the main pinmux. Instead of treating them as one and
the same device, split them up so that they are each their own devices.
Also add gpio-ranges properties to the corresponding GPIO controllers
such that the pinmux and GPIO controllers can be paired up properly.
Jon Hunter [Fri, 28 Oct 2022 12:35:56 +0000 (13:35 +0100)]
arm64: tegra: Update console for Jetson Xavier and Orin
The Tegra Combined UART (TCU) is the default serial interface for Jetson
Xavier and Orin platforms and so update the bootargs for these platforms
to use the TCU.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Wed, 19 Oct 2022 13:29:02 +0000 (14:29 +0100)]
arm64: tegra: Populate Tegra234 PWMs
Populate all the PWM devices for Tegra234. Finally, update the
compatible string for the existing 'pwm1' node to just be 'tegra194-pwm'
and remove the fallback to 'tegra186-pwm', which aligns with the
binding documentation.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Wed, 19 Oct 2022 13:16:13 +0000 (14:16 +0100)]
arm64: tegra: Remove unused property for I2C
Commit 156af9de0932 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
populated the I2C device nodes for Tegra234. One of these nodes
contains the property 'nvidia,hw-instance-id' which is neither
documented or used. Remove this unused property.
arm64: tegra: Fix Prefetchable aperture ranges of Tegra234 PCIe controllers
commit edf408b946d3 ("PCI: dwc: Validate iATU outbound mappings against
hardware constraints") exposes an issue with the existing partitioning of
the aperture space where the Prefetchable apertures of controllers
C5, C7 and C9 in Tegra234 cross the 32GB boundary hardware constraint.
This patch makes sure that the Prefetchable region doesn't spill over
the 32GB boundary.
Mikko Perttunen [Tue, 20 Sep 2022 08:11:59 +0000 (11:11 +0300)]
arm64: tegra: Add NVDEC on Tegra234
Add a device tree node for NVDEC on Tegra234.
Booting the firmware requires some information regarding offsets
within the firmware binary. These are passed through the device
tree, but since the values vary depending on the firmware version,
and the firmware itself is not available to the OS, the flasher is
expected to provide a device tree overlay with values corresponding
to the firmware it is flashing. The overlay then replaces the
placeholder values here.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Mikko Perttunen [Tue, 6 Sep 2022 11:01:34 +0000 (14:01 +0300)]
arm64: tegra: Fix ranges for host1x nodes
The currently specified 'ranges' properties don't actually include
all devices under the host1x bus on Tegra194 and Tegra234. Expand
them appropriately.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
dt-bindings: pinctrl: tegra194: Separate instances
Tegra194 has two separate instances of the pin controller, one called
AON (in the always-on domain) and another called "main". Instead of
treating them as a single pin controller, split them up into two
separate controllers. Doing so allows the mapping between the pinmux and
GPIO controllers to be trivial identity mappings and more cleanly
separates the AON from the main IP blocks.
Note that while this changes the DT node in an incompatible way, this
doesn't have any practical implications for backwards-compatibility. The
reason for this is that device trees have only reconfigured a very
narrow subset of pins of the main controller, so the new driver will
remain backwards-compatible with old device trees.
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
Add compatible for nvidia,tegra234-pwm with nvidia,tegra194-pwm as a
fallback. The PWM controller blocks are identical to the ones found on
the Tegra194 SoC. No driver changes are required and compatible string
"nvidia,tegra194-pwm" will be used as a fallback.
Mikko Perttunen [Tue, 20 Sep 2022 08:11:58 +0000 (11:11 +0300)]
dt-bindings: Add bindings for Tegra234 NVDEC
Update NVDEC bindings for Tegra234. This new engine version only has
two memory clients, but now requires three clocks, and as a bigger
change the engine loads firmware from a secure carveout configured by
the bootloader.
For the latter, we need to add a phandle to the memory controller
to query the location of this carveout, and several other properties
containing offsets into the firmware inside the carveout. This
carveout is not accessible by the CPU, but is needed by NVDEC,
so we need this information to be relayed from the bootloader.
As the binding was getting large with many conditional properties,
also split the Tegra234 version out into a separate file.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
AngeloGioacchino Del Regno [Thu, 27 Oct 2022 09:55:02 +0000 (11:55 +0200)]
arm64: dts: mediatek: mt6795: Add support for eMMC/SD/SDIO controllers
Add the mmc nodes to support all of the four controllers, used for
eMMC, SD/MicroSD and SDIO storage.
All of these controller nodes are left disabled by default, as
usage is board dependent.
AngeloGioacchino Del Regno [Thu, 27 Oct 2022 09:55:01 +0000 (11:55 +0200)]
arm64: dts: mediatek: mt6795: Add support for APDMA and wire up UART DMAs
This SoC has a DMA controller with tx/rx channels for all of the
UART controller IPs: add the apdma node and wire up the DMAs on
all controllers.
When one of the UART controllers is used as a serial console,
the DMA will be automatically ignored.
AngeloGioacchino Del Regno [Thu, 27 Oct 2022 09:55:00 +0000 (11:55 +0200)]
arm64: dts: mediatek: mt6795: Replace UART dummy clocks with pericfg
The UART nodes had a dummy clock for early bringup, as it is
expected that these are left on by the bootloader: now that
the pericfg clock controller is supported, we can replace
them with the real clocks.
Bo-Chen Chen [Thu, 10 Nov 2022 06:37:16 +0000 (14:37 +0800)]
arm64: dts: mediatek: cherry: Add edptx and dptx support
In cherry projects, we use edptx as the internal display interface
and use dptx as the external display interface. To support this, we
need to add more properties.
- Add pinctrls for edptx and dptx.
- Add ports for edptx and dptx.
The port connections for the internal and external display:
dp-intf0 -> edptx -> panel
dp-intf1 -> dptx
The edptx endpoint is kept empty for now, as the panel addition will
come in a later commit.
Bo-Chen Chen [Thu, 10 Nov 2022 06:37:14 +0000 (14:37 +0800)]
arm64: dts: mt8195: Add edptx and dptx nodes
In MT8195, we use edptx as the internal display interface and use
dptx as the external display interface. Therefore, we need to add
these nodes to support the internal display and the external display.
- Add dp calibration data in the efuse node.
- Add edptx and dptx nodes for MT8195.
AngeloGioacchino Del Regno [Thu, 13 Oct 2022 15:22:08 +0000 (17:22 +0200)]
arm64: dts: mt2712e: Fix unit address for pinctrl node
The unit address for the pinctrl node is (0x)1000b000 and not
(0x)10005000, which is the syscfg_pctl_a address instead.
This fixes the following warning:
arch/arm64/boot/dts/mediatek/mt2712e.dtsi:264.40-267.4: Warning
(unique_unit_address): /syscfg_pctl_a@10005000: duplicate
unit-address (also used in node /pinctrl@10005000)
AngeloGioacchino Del Regno [Thu, 13 Oct 2022 15:22:06 +0000 (17:22 +0200)]
arm64: dts: mt6779: Fix devicetree build warnings
Rename fixed-clock oscillators to oscillator-26m and oscillator-32k
and remove the unit address to fix the unit_address_vs_reg warning;
fix the unit address for interrupt and intpol controllers by
removing a leading zero in their unit address.
This commit fixes the following warnings:
(unit_address_vs_reg): /oscillator@0: node has a unit name, but
no reg or ranges property
(unit_address_vs_reg): /oscillator@1: node has a unit name, but
no reg or ranges property
(simple_bus_reg): /soc/interrupt-controller@0c000000: simple-bus
unit address format error, expected "c000000"
(simple_bus_reg): /soc/intpol-controller@0c53a650: simple-bus
unit address format error, expected "c53a650"
AngeloGioacchino Del Regno [Thu, 13 Oct 2022 15:22:05 +0000 (17:22 +0200)]
arm64: dts: mt7896a: Fix unit_address_vs_reg warning for oscillator
Rename the oscillator fixed-clock to oscillator-40m and remove
the unit address to fix warnings.
arch/arm64/boot/dts/mediatek/mt7986a.dtsi:17.23-22.4: Warning
(unit_address_vs_reg): /oscillator@0: node has a unit name,
but no reg or ranges property
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A78) cluster at a maximum of 3000MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculate the mean result for each cluster
4. Calculate DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scale results to 1024:
result_c0 = (dmips_mhz_c0 - min_dmips_mhz(c0, c1)) /
(max_dmips_mhz(c0, c1) - min_dmips_mhz(c0, c1)) * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 11990400 Dhry/s
Cluster 1 (BIG): 59809036 Dhry/s
The calculated scaled results are:
Cluster 0: 307,934312801831 (rounded to 308)
Cluster 1: 1024
Arnd Bergmann [Mon, 21 Nov 2022 10:01:48 +0000 (11:01 +0100)]
Merge branch 'dt/dtbo-rename' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into soc/dt
* 'dt/dtbo-rename' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
kbuild: Cleanup DT Overlay intermediate files as appropriate
staging: pi433: overlay: Rename overlay source file from .dts to .dtso
of: overlay: rename overlay source files from .dts to .dtso
kbuild: Allow DTB overlays to built into .dtbo.S files
kbuild: Allow DTB overlays to built from .dtso named source files
Arnd Bergmann [Mon, 21 Nov 2022 09:53:52 +0000 (10:53 +0100)]
Merge tag 'samsung-dt64-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.2
Correct pin drive strength macros (names) and values used on Tesla FSD
SoC.
* tag 'samsung-dt64-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: fsd: fix drive strength values as per FSD HW UM
arm64: dts: fsd: fix drive strength macros as per FSD HW UM
Aakarsh Jain [Wed, 16 Nov 2022 09:30:09 +0000 (10:30 +0100)]
ARM: dts: exynos: Add new SoC specific compatible string for Exynos3250 SoC
Exynos3250 and Exynos5420 are using same compatible string for MFC codec
device but they have different clock hierarchy and complexity. Add new
compatible string followed by mfc-v7 fallback for Exynos3250 SoC.
Andrew Davis [Mon, 24 Oct 2022 17:34:31 +0000 (12:34 -0500)]
arm64: dts: freescale: Rename DTB overlay source files from .dts to .dtso
DTB Overlays (.dtbo) can now be built from source files with the
extension (.dtso). This makes it clear what is the content of the files
and differentiates them from base DTB source files.
Convert the DTB overlay source files in the arm64/freescale directory.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adrian Alonso [Thu, 17 Nov 2022 09:54:03 +0000 (17:54 +0800)]
arm64: dts: imx8mm-evk: add vcc supply for pca6416
pca6146 requires vcc-supply to work on i.MX8MM-EVK board.
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com> Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Haibo Chen [Thu, 17 Nov 2022 09:54:02 +0000 (17:54 +0800)]
arm64: dts: imx8m[m,q]-evk: change to use off-on-delay-us in regulator
Some SD Card controller and power circuitry has increased capacitance,
so the usual toggling of regulator to power the card off and on
is insufficient.
According to SD spec, for sd card power reset operation, the sd card
supply voltage needs to be lower than 0.5v and keep over 1ms, otherwise,
next time power back the sd card supply voltage to 3.3v, sd card can't
support SD3.0 mode again.
This patch add the off-on-delay-us, make sure the sd power reset behavior
is align with the specification. Without this patch, when do quick system
suspend/resume test, some sd card can't work at SD3.0 mode after system
resume back.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Thu, 17 Nov 2022 09:54:01 +0000 (17:54 +0800)]
arm64: dts: imx8mn-evk: enable uart1
Enable uart1 for BT usage
Configure the clock to source from IMX8MN_SYS_PLL1_80M, because the uart
could only support max 1.5M buadrate if using OSC_24M as clock source.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Thu, 17 Nov 2022 09:53:59 +0000 (17:53 +0800)]
arm64: dts: imx8mn-evk: set off-on-delay-us in regulator
Some SD Card controller and power circuitry has increased capacitance,
so the usual toggling of regulator to power the card off and on
is insufficient.
According to SD spec, for sd card power reset operation, the sd card
supply voltage needs to be lower than 0.5v and keep over 1ms, otherwise,
next time power back the sd card supply voltage to 3.3v, sd card can't
support SD3.0 mode again.
This patch add the off-on-delay-us, make sure the sd power reset behavior
is align with the specification. Without this patch, when do quick system
suspend/resume test, some sd card can't work at SD3.0 mode after system
resume back.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Thu, 17 Nov 2022 09:53:58 +0000 (17:53 +0800)]
arm64: dts: imx8mn-evk: update vdd_soc dvs voltage
Per schematic, BUCK1 is for VDD_SOC&DRAM&PU_0V9. The nxp,dvs-run-voltage
and nxp,dvs-standby-voltage need set for BUCK1, not BUCK2.
BUCK2 is for A53, which is handled by DVFS, so no need dvs property.
nxp,dvs-run-voltage is not needed, since bootloader must configure
voltage to make system boot well.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Han Xu [Thu, 17 Nov 2022 09:53:56 +0000 (17:53 +0800)]
arm64: dts: imx8mp-evk: enable fspi nor on imx8mp evk
enable fspi nor on imx8mp evk dts
Reviewed-by: Frank Li <frank.li@nxp.com> Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Thu, 17 Nov 2022 09:53:55 +0000 (17:53 +0800)]
arm64: dts: imx8mp-evk: enable uart1/3 ports
Enable uart1/3 ports for evk board.
Configure the clock to source from IMX8MP_SYS_PLL1_80M, because the uart
could only support max 1.5M buadrate if using OSC_24M as clock source.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Clark Wang [Thu, 17 Nov 2022 09:53:54 +0000 (17:53 +0800)]
ARM64: dts: imx8mp-evk: add pwm support
Enable pwm1/2/4 support.
Enable pwm1 on pin GPIO1_IO01 for DSI_BL_PWM
pwm2 on pin GPIO1_IO11 for LVDS_BL_PWM
pwm4 on pin SAI5_RXFS for J21-32
Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Colibri standard provides a GPIO called USBC_DET to switch from
USB Host to USB Device and back. Make use of this GPIO by adding it
with usb-connector framework.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrew Davis [Mon, 14 Nov 2022 20:59:39 +0000 (14:59 -0600)]
kbuild: Cleanup DT Overlay intermediate files as appropriate
%.dtbo.o and %.dtbo.S files are used to build-in DT Overlay. They should
should not be removed by Make or the kernel will be needlessly rebuilt.
These should be removed by "clean" and ignored by git like other
intermediate files.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Andrew Davis <afd@ti.com> Fixes: 941214a512d8 ("kbuild: Allow DTB overlays to built into .dtbo.S files") Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Masahiro Yamada <masahiroy@kernel.org> Link: https://lore.kernel.org/r/20221114205939.27994-1-afd@ti.com Signed-off-by: Rob Herring <robh@kernel.org>
arm64: dts: socfpga: Add clk-phase-sd-hs property to the sdmmc node
The sdmmc controller's CIU(Card Interface Unit) clock's phase can be
adjusted through the register in the system manager. Add the binding
"altr,sysmgr-syscon" to the SDMMC node for the driver to access the
system manager. Add the "clk-phase-sd-hs" property in the SDMMC node to
designate the smpsel and drvsel properties for the CIU clock.
projects / users / jedix / linux-maple.git / log