Raphael Gallais-Pou [Thu, 9 Jan 2025 15:58:42 +0000 (16:58 +0100)]
net: stmmac: sti: Switch from CONFIG_PM_SLEEP guards to pm_sleep_ptr()
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Guangguan Wang [Sat, 4 Jan 2025 14:32:01 +0000 (22:32 +0800)]
net/smc: fix data error when recvmsg with MSG_PEEK flag
When recvmsg with MSG_PEEK flag, the data will be copied to
user's buffer without advancing consume cursor and without
reducing the length of rx available data. Once the expected
peek length is larger than the value of bytes_to_rcv, in the
loop of do while in smc_rx_recvmsg, the first loop will copy
bytes_to_rcv bytes of data from the position local_tx_ctrl.cons,
the second loop will copy the min(bytes_to_rcv, read_remaining)
bytes from the position local_tx_ctrl.cons again because of the
lacking of process with advancing consume cursor and reducing
the length of available data. So do the subsequent loops. The
data copied in the second loop and the subsequent loops will
result in data error, as it should not be copied if no more data
arrives and it should be copied from the position advancing
bytes_to_rcv bytes from the local_tx_ctrl.cons if more data arrives.
This issue can be reproduce by the following python script:
server.py:
import socket
import time
server_ip = '0.0.0.0'
server_port = 12346
server_socket = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
server_socket.bind((server_ip, server_port))
server_socket.listen(1)
print('Server is running and listening for connections...')
conn, addr = server_socket.accept()
print('Connected by', addr)
while True:
data = conn.recv(1024)
if not data:
break
print('Received request:', data.decode())
conn.sendall(b'Hello, client!\n')
time.sleep(5)
conn.sendall(b'Hello, again!\n')
conn.close()
Lorenzo Bianconi [Tue, 7 Jan 2025 22:26:28 +0000 (23:26 +0100)]
net: airoha: Fix channel configuration for ETS Qdisc
Limit ETS QoS channel to AIROHA_NUM_QOS_CHANNELS in
airoha_tc_setup_qdisc_ets() in order to align the configured channel to
the value set in airoha_dev_select_queue().
Dimitri Fedrau [Tue, 7 Jan 2025 08:23:04 +0000 (09:23 +0100)]
net: phy: dp83822: Add support for PHY LEDs on DP83822
The DP83822 supports up to three configurable Light Emitting Diode (LED)
pins: LED_0, LED_1 (GPIO1), COL (GPIO2) and RX_D3 (GPIO3). Several
functions can be multiplexed onto the LEDs for different modes of
operation. LED_0 and COL (GPIO2) use the MLED function. MLED can be routed
to only one of these two pins at a time. Add minimal LED controller driver
supporting the most common uses with the 'netdev' trigger.
Pierre-Henry Moussay adds PIC64GX compatibility to the DT bindings for
Microchip's mpfs-can IP core.
The next 3 patches are by Sean Nyekjaer and target the tcan4x5x
driver. First the DT bindings is converted to DT schema, then nWKRQ
voltage selection is added to the driver.
Dario Binacchi's patch for the sun4i_can makes the driver more
consistent by adding a likely() to the driver.
Another patch by Sean Nyekjaer for the tcan4x5x driver gets rid of a
false error message.
Charan Pedumuru converts the atmel-can DT bindings to DT schema.
The next 2 patches are by Oliver Hartkopp. The first one maps Oliver's
former mail addresses to a dedicated CAN mail address. The second one
assigns net/sched/em_canid.c additionally to the CAN maintainers.
Ariel Otilibili's patch removes dead code from the CAN dev helper.
The next 3 patches are by Sean Nyekjaer and add HW standby support to
the tcan4x5x driver.
A patch by Dario Binacchi fixes the DT bindings for the st,stm32-bxcan
driver.
The last 4 patches are by Jimmy Assarsson and target the kvaser_usb
and the kvaser_pciefd driver: error statistics are improved and
CAN_CTRLMODE_BERR_REPORTING is added.
* tag 'linux-can-next-for-6.14-20250110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: kvaser_pciefd: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_pciefd: Update stats and state even if alloc_can_err_skb() fails
can: kvaser_usb: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_usb: Update stats and state even if alloc_can_err_skb() fails
dt-bindings: can: st,stm32-bxcan: fix st,gcan property type
can: m_can: call deinit/init callback when going into suspend/resume
can: tcan4x5x: add deinit callback to set standby mode
can: m_can: add deinit callback
can: dev: can_get_state_str(): Remove dead code
MAINTAINERS: assign em_canid.c additionally to CAN maintainers
mailmap: add an entry for Oliver Hartkopp
dt-bindings: net: can: atmel: Convert to json schema
can: tcan4x5x: get rid of false clock errors
can: sun4i_can: continue to use likely() to check skb
can: tcan4x5x: add option for selecting nWKRQ voltage
dt-bindings: can: tcan4x5x: Document the ti,nwkrq-voltage-vio option
dt-bindings: can: convert tcan4x5x.txt to DT schema
dt-bindings: can: mpfs: add PIC64GX CAN compatibility
====================
Jakub Kicinski [Fri, 10 Jan 2025 00:49:24 +0000 (16:49 -0800)]
net: hide the definition of dev_get_by_napi_id()
There are no module callers of dev_get_by_napi_id(),
and commit d1cacd747768 ("netdev: prevent accessing NAPI instances
from another namespace") proves that getting NAPI by id
needs to be done with care. So hide dev_get_by_napi_id().
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Joe Damato <jdamato@fastly.com> Link: https://patch.msgid.link/20250110004924.3212260-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 10 Jan 2025 00:45:04 +0000 (16:45 -0800)]
net: warn during dump if NAPI list is not sorted
Dump continuation depends on the NAPI list being sorted.
Broken netlink dump continuation may be rare and hard to debug
so add a warning if we notice the potential problem while walking
the list.
Alexander Sverdlin [Thu, 9 Jan 2025 21:42:13 +0000 (22:42 +0100)]
net: ethernet: ti: cpsw: fix the comment regarding VLAN-aware ALE
In all 3 cases (cpsw, cpsw-new, am65-cpsw) ALE is being configured in
VLAN-aware mode, while the comment states the opposite. Seems to be a typo
copy-pasted from one driver to another. Fix the commend which has been
puzzling some people (including me) for at least a decade.
Sabrina Dubroca [Thu, 9 Jan 2025 22:30:54 +0000 (23:30 +0100)]
tls: skip setting sk_write_space on rekey
syzbot reported a problem when calling setsockopt(SO_SNDBUF) after a
rekey. SO_SNDBUF calls sk_write_space, ie tls_write_space, which then
calls the original socket's sk_write_space, saved in
ctx->sk_write_space. Rekeys should skip re-assigning
ctx->sk_write_space, so we don't end up with tls_write_space calling
itself.
Li RongQing [Thu, 9 Jan 2025 11:10:57 +0000 (19:10 +0800)]
net: ethtool: Use hwprov under rcu_read_lock
hwprov should be protected by rcu_read_lock to prevent possible UAF
Fixes: 4c61d809cf60 ("net: ethtool: Fix suspicious rcu_dereference usage") Signed-off-by: Li RongQing <lirongqing@baidu.com> Acked-by: Kory Maincent <kory.maincent@bootlin.com>
diff with v1: move and use err varialbe, instead of define a new variable
Etienne Champetier [Thu, 9 Jan 2025 03:28:18 +0000 (22:28 -0500)]
ipvlan: Support bonding events
This allows ipvlan to function properly on top of
bonds using active-backup mode.
This was implemented for macvlan in 2014 in commit 4c9912556867 ("macvlan: Support bonding events").
====================
net: stmmac: clean up and fix EEE implementation
This is a rework of stmmac's EEE support in light of the addition of EEE
management to phylib. It's slightly more than 15 patches, but I think it
makes sense to be so.
Patch 1 adds configuration of the receive clock phy_eee_rx_clock_stop()
(which was part of another series, but is necessary for this patch set.)
Patch 2 converts stmmac to use phylib's tracking of tx_lpi_timer.
Patch 3 corrects the data type used for things involving the LPI
timer. The user API uses u32, so stmmac should do too, rather than
blindly converting it to "int". eee_timer is left for patch 4.
Patch 4 (new) uses an unsigned int for eee_timer.
Patch 5 makes stmmac EEE state depend on phylib's enable_tx_lpi flag,
thus using phylib's resolution of EEE state.
Patch 6 removes redundant code from the ethtool EEE operations.
Patch 7 removes some redundant code in stmmac_disable_eee_mode()
and renames it to stmmac_disable_sw_eee_mode() to better reflect its
purpose.
Patch 8 removes the driver private tx_lpi_enabled, which is managed by
phylib since patch 4.
Patch 9 removes the dependence of EEE error statistics on the EEE
enable state, instead depending on whether EEE is supported by the
hardware.
Patch 10 removes phy_init_eee(), instead using phy_eee_rx_clock_stop()
to configure whether the PHY may stop the receive clock.
Patch 11 removes priv->eee_tw_timer, which is only ever set to one
value at probe time, effectively it is a constant. Hence this is
unnecessary complexity.
Patch 12 moves priv->eee_enabled into stmmac_eee_init(), and placing
it under the protection of priv->lock, except when EEE is not
supported (where it becomes constant-false.)
Patch 13 moves priv->eee_active also into stmmac_eee_init(), so
the indication whether EEE should be enabled or not is passed in
to this function.
Since both priv->eee_enabled and priv->eee_active are assigned
true/false values, they should be typed "bool". Make it sew in
patch 14. No Singer machine required.
Patch 15 moves the initialisation of priv->eee_ctrl_timer to the
probe function - it makes no sense to re-initialise the timer each
time we want to start using it.
Patch 16 removes the unnecessary EEE handling in the driver tear-down
method. The core net code will have brought the interface down
already, meaning EEE has already been disabled.
Patch 17 reorganises the code to split the hardware LPI timer
control paths from the software LPI timer paths.
Patch 18 works on this further by eliminating
stmmac_lpi_entry_timer_config() and making direct calls to the new
functions. This reveals a potential bug where priv->eee_sw_timer_en
is set true when EEE is disabled. This is not addressed in this
series, but will be in a future separate patch - so that if fixing
that causes a regression, it can be handled separately.
====================
Remove stmmac_lpi_entry_timer_config(), setting priv->eee_sw_timer_en
at the original call sites, and calling the appropriate
stmmac_xxx_hw_lpi_timer() function. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEq-0002LQ-PC@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:55 +0000 (16:48 +0000)]
net: stmmac: split hardware LPI timer control
Provide stmmac_disable_hw_lpi_timer() and stmmac_enable_hw_lpi_timer()
to control the hardware transmit LPI timer.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEl-0002LK-LA@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:50 +0000 (16:48 +0000)]
net: stmmac: remove unnecessary EEE handling in stmmac_release()
phylink_stop() will cause phylink to call the mac_link_down() operation
before phylink_stop() returns. As mac_link_down() will call
stmmac_eee_init(false), this will set both priv->eee_active and
priv->eee_enabled to be false, deleting the eee_ctrl_timer if
priv->eee_enabled was previously set.
As stmmac_release() calls phylink_stop() before checking whether
priv->eee_enabled is true, this is a condition that can never be
satisfied, and thus the code within this if() block will never be
executed. Remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEg-0002LE-HH@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:45 +0000 (16:48 +0000)]
net: stmmac: move setup of eee_ctrl_timer to stmmac_dvr_probe()
Move the initialisation of the EEE software timer to the probe function
as it is unnecessary to do this each time we enable software LPI.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEb-0002L8-DJ@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:40 +0000 (16:48 +0000)]
net: stmmac: use boolean for eee_enabled and eee_active
priv->eee_enabled and priv->eee_active are both assigned using boolean
values. Type them as bool rather than int.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEW-0002L2-9w@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:35 +0000 (16:48 +0000)]
net: stmmac: move priv->eee_active into stmmac_eee_init()
Since all call sites of stmmac_eee_init() assign priv->eee_active
immediately before, pass this state into stmmac_eee_init() and
assign priv->eee_active within this function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZER-0002Kv-5O@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:30 +0000 (16:48 +0000)]
net: stmmac: move priv->eee_enabled into stmmac_eee_init()
All call sites for stmmac_eee_init() assign the return code to
priv->eee_enabled. Rather than having this coded at each call site,
move the assignment inside stmmac_eee_init().
Since stmmac_init_eee() takes priv->lock before checking the state of
priv->eee_enabled, move the assignment within the locked region. Also,
stmmac_suspend() checks the state of this member under the lock. While
two concurrent calls to stmmac_init_eee() aren't possible, there is
a possibility that stmmac_suspend() may run concurrently with a change
of priv->eee_enabled unless we modify it under the lock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEM-0002Kq-2Z@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:24 +0000 (16:48 +0000)]
net: stmmac: remove priv->eee_tw_timer
priv->eee_tw_timer is only assigned during initialisation to a
constant value (STMMAC_DEFAULT_TWT_LS) and then never changed.
Remove priv->eee_tw_timer, and instead use STMMAC_DEFAULT_TWT_LS
for both uses in stmmac_eee_init().
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEG-0002Kk-VH@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:19 +0000 (16:48 +0000)]
net: stmmac: convert to use phy_eee_rx_clock_stop()
Convert stmmac to use phy_eee_rx_clock_stop() to set the PHY receive
clock stop in LPI setting, rather than calling the legacy
phy_init_eee() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZEB-0002Ke-RZ@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:14 +0000 (16:48 +0000)]
net: stmmac: report EEE error statistics if EEE is supported
Report the number of EEE error statistics in the xstats even when EEE
is not enabled in hardware, but is supported. The PHY maintains this
counter even when EEE is not enabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZE6-0002KY-Nx@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:09 +0000 (16:48 +0000)]
net: stmmac: remove priv->tx_lpi_enabled
Through using phylib's EEE state, priv->tx_lpi_enabled has become a
write-only variable. Remove it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZE1-0002KS-K1@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:48:04 +0000 (16:48 +0000)]
net: stmmac: clean up stmmac_disable_eee_mode()
stmmac_disable_eee_mode() is now only called from stmmac_xmit() when
both priv->tx_path_in_lpi_mode and priv->eee_sw_timer_en are true.
Therefore:
if (!priv->eee_sw_timer_en)
in stmmac_disable_eee_mode() will never be true, so this is dead code.
Remove it, and rename the function to indicate that it now only deals
with software based EEE mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZDw-0002KL-Gg@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:47:59 +0000 (16:47 +0000)]
net: stmmac: remove redundant code from ethtool EEE ops
Setting edata->tx_lpi_enabled in stmmac_ethtool_op_get_eee() gets
overwritten by phylib, so there's no point setting this.
In stmmac_ethtool_op_set_eee(), now that stmmac is using the result of
phylib's evaluation of EEE, there is no need to handle anything in the
ethtool EEE ops other than calling through to the appropriate phylink
function, which will pass on to phylib the users request.
As stmmac_disable_eee_mode() is now no longer called from outside
stmmac_main.c, make it static.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZDr-0002KF-Cv@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:47:54 +0000 (16:47 +0000)]
net: stmmac: make EEE depend on phy->enable_tx_lpi
Make stmmac EEE depend on phylib's evaluation of user settings and PHY
negotiation, as indicated by phy->enable_tx_lpi. This will ensure when
phylib has evaluated that the user has disabled LPI, phy_init_eee()
will not be called, and priv->eee_active will be false, causing LPI/EEE
to be disabled.
This is an interim measure - phy_init_eee() will be removed in a later
patch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZDm-0002K9-9w@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:47:49 +0000 (16:47 +0000)]
net: stmmac: use unsigned int for eee_timer
Since eee_timer is used to initialise priv->tx_lpi_timer, this also
should be unsigned to avoid a negative number being interpreted as a
very large positive number. Note that this makes the check for negative
numbers passed in as a module parameter redundant, and passing a
negative number will now produce a large delay rather than the
default. Since the default is used without an argument, passing a
negative number would be quite obscure. However, if users do, then
this will need to be revisited.
Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZDh-0002K3-6y@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:47:44 +0000 (16:47 +0000)]
net: stmmac: use correct type for tx_lpi_timer
The ethtool interface uses u32 for tx_lpi_timer, and so does phylib.
Use u32 to store this internally within stmmac rather than "int"
which could misinterpret large values.
Correct "value" in dwmac4_set_eee_lpi_entry_timer() to use u32
rather than int, which is derived from tx_lpi_timer. Even though this
path won't be used with values larger than STMMAC_ET_MAX, this brings
consistency of type usage to the stmmac code for this variable.
We leave eee_timer unchanged for now, with the assumption that values
up to INT_MAX will safely fit in a u32.
Russell King (Oracle) [Wed, 8 Jan 2025 16:47:38 +0000 (16:47 +0000)]
net: stmmac: move tx_lpi_timer tracking to phylib
When stmmac_ethtool_op_get_eee() is called, stmmac sets the tx_lpi_timer
and tx_lpi_enabled members, and then calls into phylink and thus phylib.
phylib overwrites these members.
phylib will also cause a link down/link up transition when settings
that impact the MAC have been changed.
Convert stmmac to use the tx_lpi_timer setting in struct phy_device,
updating priv->tx_lpi_timer each time when the link comes up, rather
than trying to maintain this user setting itself. We initialise the
phylib tx_lpi_timer setting by doing a get_ee-modify-set_eee sequence
with the last known priv->tx_lpi_timer value. In order for this to work
correctly, we also need this member to be initialised earlier.
As stmmac_eee_init() is no longer called outside of stmmac_main.c, make
it static.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZDW-0002Jr-W3@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 8 Jan 2025 16:47:33 +0000 (16:47 +0000)]
net: phy: add configuration of rx clock stop mode
Add a function to allow configuration of the PCS's clock stop enable
bit, used to configure whether the xMII receive clock can be stopped
during LPI mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tVZDR-0002Jl-Ry@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jimmy Assarsson [Mon, 30 Dec 2024 14:26:45 +0000 (15:26 +0100)]
can: kvaser_pciefd: Add support for CAN_CTRLMODE_BERR_REPORTING
Add support for CAN_CTRLMODE_BERR_REPORTING,
allowing Bus Error Reporting to be enabled or disabled.
Previously, Bus Error Reporting was always active.
Co-developed-by: Alison Below <alisonbelow@gmail.com> Signed-off-by: Alison Below <alisonbelow@gmail.com> Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://patch.msgid.link/20241230142645.128244-4-extja@kvaser.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jimmy Assarsson [Mon, 30 Dec 2024 14:26:44 +0000 (15:26 +0100)]
can: kvaser_pciefd: Update stats and state even if alloc_can_err_skb() fails
Ensure statistics, error counters, and CAN state are updated consistently,
even when alloc_can_err_skb() fails during state changes or error message
frame reception.
Jimmy Assarsson [Mon, 30 Dec 2024 14:26:43 +0000 (15:26 +0100)]
can: kvaser_usb: Add support for CAN_CTRLMODE_BERR_REPORTING
Add support for CAN_CTRLMODE_BERR_REPORTING,
allowing Bus Error Reporting to be enabled or disabled.
Previously, Bus Error Reporting was always active.
Jimmy Assarsson [Mon, 30 Dec 2024 14:26:42 +0000 (15:26 +0100)]
can: kvaser_usb: Update stats and state even if alloc_can_err_skb() fails
Ensure statistics, error counters, and CAN state are updated consistently,
even when alloc_can_err_skb() fails during state changes or error message
frame reception.
Marc Kleine-Budde [Fri, 10 Jan 2025 10:05:46 +0000 (11:05 +0100)]
Merge patch series "can: tcan4x5x/m_can: use standby mode when down and in suspend"
Sean Nyekjaer <sean@geanix.com> says:
When downing the tcan4x5x there is no reason to keep the tcan4x5x in
"normal" mode and waste power. So set standby mode when the interface
is down and normal mode when interface is up.
Also when going into suspend, set the tcan4x5x into standby mode. The
tcan4x5x can still be used as a wake-source when in standby as low
power RX is enabled.
Sean Nyekjaer [Fri, 22 Nov 2024 14:52:22 +0000 (15:52 +0100)]
can: m_can: add deinit callback
This is added in preparation for calling standby mode in the tcan4x5x
driver or other users of m_can.
For the tcan4x5x; If Vsup 12V, standby mode will save 7-8mA, when the
interface is down.
====================
netconsole: selftest for userdata overflow
Implement comprehensive testing for netconsole userdata entry handling,
demonstrating correct behavior when creating maximum entries and
preventing unauthorized overflow.
Refactor existing test infrastructure to support modular, reusable
helper functions that validate strict entry limit enforcement.
Also, add a warning if update_userdata() sees more than
MAX_USERDATA_ITEMS entries. This shouldn't happen and it is a bug that
shouldn't be silently ignored.
Breno Leitao [Wed, 8 Jan 2025 11:50:27 +0000 (03:50 -0800)]
netconsole: selftest: Delete all userdata keys
Modify the cleanup function to remove all userdata keys created during the
test, instead of just deleting a single predefined key. This ensures a
more thorough cleanup of temporary resources.
Move the KEY_PATH variable definition inside the set_user_data function
to reduce global variables and improve encapsulation. The KEY_PATH
variable is now dynamically created when setting user data.
This change has no effect on the current test, while improving an
upcoming test that would create several userdata entries.
Breno Leitao [Wed, 8 Jan 2025 11:50:26 +0000 (03:50 -0800)]
netconsole: selftest: Split the helpers from the selftest
Split helper functions from the netconsole basic test into a separate
library file to enable reuse across different netconsole tests. This
change only moves the existing helper functions to lib/sh/lib_netcons.sh
while preserving the same test functionality.
The helpers provide common functions for:
- Setting up network namespaces and interfaces
- Managing netconsole dynamic targets
- Setting user data
- Handling test dependencies
- Cleanup operations
Do not make any change in the code, other than the mechanical
separation.
This series adds an install target for ynl. The python code
is moved to a subdirectory, so it can be used as a package
with flat layout, as well as directly from the tree.
To try the install as a non-root user you can run:
$ mkdir /tmp/myroot
$ make DESTDIR=/tmp/myroot install
Jakub Kicinski [Wed, 8 Jan 2025 20:07:58 +0000 (12:07 -0800)]
tools: ynl-gen-c: improve support for empty nests
Empty nests are the same size as a flag at the netlink level
(just a 4 byte nlattr without a payload). They are sometimes
useful in case we want to only communicate a presence of
something but may want to add more details later.
This may be the case in the upcoming io_uring ZC patches,
for example.
Improve handling of nested empty structs. We already support
empty structs since a lot of netlink replies are empty, but
for nested ones we need minor tweaks to avoid pointless empty
lines and unused variables.
* tag 'net-6.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
rds: sysctl: rds_tcp_{rcv,snd}buf: avoid using current->nsproxy
sctp: sysctl: plpmtud_probe_interval: avoid using current->nsproxy
sctp: sysctl: udp_port: avoid using current->nsproxy
sctp: sysctl: auth_enable: avoid using current->nsproxy
sctp: sysctl: rto_min/max: avoid using current->nsproxy
sctp: sysctl: cookie_hmac_alg: avoid using current->nsproxy
mptcp: sysctl: blackhole timeout: avoid using current->nsproxy
mptcp: sysctl: sched: avoid using current->nsproxy
mptcp: sysctl: avail sched: remove write access
MAINTAINERS: remove Lars Povlsen from Microchip Sparx5 SoC
MAINTAINERS: remove Noam Dagan from AMAZON ETHERNET
MAINTAINERS: remove Ying Xue from TIPC
MAINTAINERS: remove Mark Lee from MediaTek Ethernet
MAINTAINERS: mark stmmac ethernet as an Orphan
MAINTAINERS: remove Andy Gospodarek from bonding
MAINTAINERS: update maintainers for Microchip LAN78xx
MAINTAINERS: mark Synopsys DW XPCS as Orphan
net/mlx5: Fix variable not being completed when function returns
rtase: Fix a check for error in rtase_alloc_msix()
net: stmmac: dwmac-tegra: Read iommu stream id from device tree
...
John Daley [Tue, 7 Jan 2025 21:41:59 +0000 (13:41 -0800)]
enic: Fix typo in comment in table indexed by link speed
The RX adaptive interrupt moderation table is indexed by link speed
range, where the last row of the table is the catch-all for all link
speeds greater than 10Gbps. The comment said 10 - 40Gbps, but since
there are now adapters with link speeds than 40Gbps, the comment is now
wrong and should indicate it applies to all speeds greater than 10Gbps.
Co-developed-by: Nelson Escobar <neescoba@cisco.com> Signed-off-by: Nelson Escobar <neescoba@cisco.com> Co-developed-by: Satish Kharat <satishkh@cisco.com> Signed-off-by: Satish Kharat <satishkh@cisco.com> Signed-off-by: John Daley <johndale@cisco.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Link: https://patch.msgid.link/20250107214159.18807-4-johndale@cisco.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
John Daley [Tue, 7 Jan 2025 21:41:58 +0000 (13:41 -0800)]
enic: Obtain the Link speed only after the link comes up
The link speed is obtained in the RX adaptive coalescing function. It
was being called at probe time when the link may not be up. Change the
call to run after the Link comes up.
The impact of not getting the correct link speed was that the low end of
the adaptive interrupt range was always being set to 0 which could have
caused a slight increase in the number of RX interrupts.
Co-developed-by: Nelson Escobar <neescoba@cisco.com> Signed-off-by: Nelson Escobar <neescoba@cisco.com> Co-developed-by: Satish Kharat <satishkh@cisco.com> Signed-off-by: Satish Kharat <satishkh@cisco.com> Signed-off-by: John Daley <johndale@cisco.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Link: https://patch.msgid.link/20250107214159.18807-3-johndale@cisco.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
John Daley [Tue, 7 Jan 2025 21:41:57 +0000 (13:41 -0800)]
enic: Move RX coalescing set function
Move the function used for setting the RX coalescing range to before
the function that checks the link status. It needs to be called from
there instead of from the probe function.
There is no functional change.
Co-developed-by: Nelson Escobar <neescoba@cisco.com> Signed-off-by: Nelson Escobar <neescoba@cisco.com> Co-developed-by: Satish Kharat <satishkh@cisco.com> Signed-off-by: Satish Kharat <satishkh@cisco.com> Signed-off-by: John Daley <johndale@cisco.com> Link: https://patch.msgid.link/20250107214159.18807-2-johndale@cisco.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Krzysztof Kozlowski [Wed, 8 Jan 2025 12:02:42 +0000 (13:02 +0100)]
dt-bindings: net: qcom,ipa: Use recommended MBN firmware format in DTS example
All Qualcomm firmwares uploaded to linux-firmware are in MBN format,
instead of split MDT. No functional changes, just correct the DTS
example so people will not rely on unaccepted files.
Linus Torvalds [Thu, 9 Jan 2025 18:16:45 +0000 (10:16 -0800)]
Merge tag 'for-6.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes.
Besides the one-liners in Btrfs there's fix to the io_uring and
encoded read integration (added in this development cycle). The update
to io_uring provides more space for the ongoing command that is then
used in Btrfs to handle some cases.
- io_uring and encoded read:
- provide stable storage for io_uring command data
- make a copy of encoded read ioctl call, reuse that in case the
call would block and will be called again
- properly initialize zlib context for hardware compression on s390
- fix max extent size calculation on filesystems with non-zoned
devices
- fix crash in scrub on crafted image due to invalid extent tree"
* tag 'for-6.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zlib: fix avail_in bytes for s390 zlib HW compression path
btrfs: zoned: calculate max_extent_size properly on non-zoned setup
btrfs: avoid NULL pointer dereference if no valid extent tree
btrfs: don't read from userspace twice in btrfs_uring_encoded_read()
io_uring: add io_uring_cmd_get_async_data helper
io_uring/cmd: add per-op data to struct io_uring_cmd_data
io_uring/cmd: rename struct uring_cache to io_uring_cmd_data
Jakub Kicinski [Thu, 9 Jan 2025 16:54:49 +0000 (08:54 -0800)]
Merge tag 'nf-25-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix imbalance between flowtable BIND and UNBIND calls to configure
hardware offload, this fixes a possible kmemleak.
2) Clamp maximum conntrack hashtable size to INT_MAX to fix a possible
WARN_ON_ONCE splat coming from kvmalloc_array(), only possible from
init_netns.
* tag 'nf-25-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: conntrack: clamp maximum hashtable size to INT_MAX
netfilter: nf_tables: imbalance in flowtable binding
====================
====================
net: sysctl: avoid using current->nsproxy
As pointed out by Al Viro and Eric Dumazet in [1], using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns as it is usually done. This could cause
unexpected issues when other operations are done on the wrong netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' or 'pernet' structure can be obtained from the table->data
using container_of().
Note that table->data could also be used directly in more places, but
that would increase the size of this fix to replace all accesses via
'net'. Probably best to avoid that for fixes.
Patches 2-9 remove access of net via current->nsproxy in sysfs handlers
in MPTCP, SCTP and RDS. There are multiple patches doing almost the same
thing, but the reason is to ease the backports.
Patch 1 is not directly linked to this, but it is a small fix for MPTCP
available_schedulers sysctl knob to explicitly mark it as read-only.
Please note that this series does not address Al's comment [2]. In SCTP,
some sysctl knobs set other sysfs-exposed variables for the min/max: two
processes could then write two linked values at the same time, resulting
in new values being outside the new boundaries. It would be great if
SCTP developers can look at this problem.
rds: sysctl: rds_tcp_{rcv,snd}buf: avoid using current->nsproxy
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The per-netns structure can be obtained from the table->data using
container_of(), then the 'net' one can be retrieved from the listen
socket (if available).
sctp: sysctl: plpmtud_probe_interval: avoid using current->nsproxy
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.probe_interval' is
used.
sctp: sysctl: udp_port: avoid using current->nsproxy
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, but that would
increase the size of this fix, while 'sctp.ctl_sock' still needs to be
retrieved from 'net' structure.
sctp: sysctl: auth_enable: avoid using current->nsproxy
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, but that would
increase the size of this fix, while 'sctp.ctl_sock' still needs to be
retrieved from 'net' structure.
sctp: sysctl: rto_min/max: avoid using current->nsproxy
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.rto_min/max' is used.
sctp: sysctl: cookie_hmac_alg: avoid using current->nsproxy
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.sctp_hmac_alg' is
used.
mptcp: sysctl: blackhole timeout: avoid using current->nsproxy
As mentioned in the previous commit, using the 'net' structure via
'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'pernet' structure can be obtained from the table->data using
container_of().
mptcp: sysctl: sched: avoid using current->nsproxy
Using the 'net' structure via 'current' is not recommended for different
reasons.
First, if the goal is to use it to read or write per-netns data, this is
inconsistent with how the "generic" sysctl entries are doing: directly
by only using pointers set to the table entry, e.g. table->data. Linked
to that, the per-netns data should always be obtained from the table
linked to the netns it had been created for, which may not coincide with
the reader's or writer's netns.
Another reason is that access to current->nsproxy->netns can oops if
attempted when current->nsproxy had been dropped when the current task
is exiting. This is what syzbot found, when using acct(2):
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
CPU: 1 UID: 0 PID: 5924 Comm: syz-executor Not tainted 6.13.0-rc5-syzkaller-00004-gccb98ccef0e5 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:proc_scheduler+0xc6/0x3c0 net/mptcp/ctrl.c:125
Code: 03 42 80 3c 38 00 0f 85 fe 02 00 00 4d 8b a4 24 08 09 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d 7c 24 28 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 02 00 00 4d 8b 7c 24 28 48 8d 84 24 c8 00 00
RSP: 0018:ffffc900034774e8 EFLAGS: 00010206
Here with 'net.mptcp.scheduler', the 'net' structure is not really
needed, because the table->data already has a pointer to the current
scheduler, the only thing needed from the per-netns data.
Simply use 'data', instead of getting (most of the time) the same thing,
but from a longer and indirect way.
Fixes: 6963c508fd7a ("mptcp: only allow set existing scheduler for net.mptcp.scheduler") Cc: stable@vger.kernel.org Reported-by: syzbot+e364f774c6f57f2c86d1@syzkaller.appspotmail.com Closes: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-2-5df34b2083e8@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
MAINTAINERS: spring 2025 cleanup of networking maintainers
Annual cleanup of inactive maintainers. To identify inactive maintainers
we use Jon Corbet's maintainer analysis script from gitdm, and some manual
scanning of lore.
Jakub Kicinski [Wed, 8 Jan 2025 15:52:42 +0000 (07:52 -0800)]
MAINTAINERS: remove Lars Povlsen from Microchip Sparx5 SoC
We have not seen emails or tags from Lars in almost 4 years.
Steen and Daniel are pretty active, but the review coverage
isn't stellar (35% of changes go in without a review tag).
Subsystem ARM/Microchip Sparx5 SoC support
Changes 28 / 79 (35%)
Last activity: 2024-11-24
Lars Povlsen <lars.povlsen@microchip.com>:
Steen Hegelund <Steen.Hegelund@microchip.com>:
Tags 6c7c4b91aa43 2024-04-08 00:00:00 15
Daniel Machon <daniel.machon@microchip.com>:
Author 48ba00da2eb4 2024-04-09 00:00:00 2
Tags f164b296638d 2024-11-24 00:00:00 6
Top reviewers:
[7]: horms@kernel.org
[1]: jacob.e.keller@intel.com
[1]: jensemil.schulzostergaard@microchip.com
[1]: horatiu.vultur@microchip.com
INACTIVE MAINTAINER Lars Povlsen <lars.povlsen@microchip.com>
Jakub Kicinski [Wed, 8 Jan 2025 15:52:41 +0000 (07:52 -0800)]
MAINTAINERS: remove Noam Dagan from AMAZON ETHERNET
Noam Dagan was added to ENA reviewers in 2021, we have not seen
a single email from this person to any list, ever (according to lore).
Git history mentions the name in 2 SoB tags from 2020.
Jakub Kicinski [Wed, 8 Jan 2025 15:52:40 +0000 (07:52 -0800)]
MAINTAINERS: remove Ying Xue from TIPC
There is a steady stream of fixes for TIPC, even tho the development
has slowed down a lot. Over last 2 years we have merged almost 70
TIPC patches, but we haven't heard from Ying Xue once:
Jakub Kicinski [Wed, 8 Jan 2025 15:52:38 +0000 (07:52 -0800)]
MAINTAINERS: mark stmmac ethernet as an Orphan
I tried a couple of things to reinvigorate the stmmac maintainers
over the last few years but with little effect. The maintainers
are not active, let the MAINTAINERS file reflect reality.
The Synopsys IP this driver supports is very popular we need
a solid maintainer to deal with the complexity of the driver.
gitdm missingmaints says:
Subsystem STMMAC ETHERNET DRIVER
Changes 344 / 978 (35%)
Last activity: 2020-05-01
Alexandre Torgue <alexandre.torgue@foss.st.com>:
Tags 1bb694e20839 2020-05-01 00:00:00 1
Jose Abreu <joabreu@synopsys.com>:
Top reviewers:
[75]: horms@kernel.org
[49]: andrew@lunn.ch
[46]: fancer.lancer@gmail.com
INACTIVE MAINTAINER Jose Abreu <joabreu@synopsys.com>
Jakub Kicinski [Wed, 8 Jan 2025 15:52:36 +0000 (07:52 -0800)]
MAINTAINERS: update maintainers for Microchip LAN78xx
Woojung Huh seems to have only replied to the list 35 times
in the last 5 years, and didn't provide any reviews in 3 years.
The LAN78XX driver has seen quite a bit of activity lately.
gitdm missingmaints says:
Subsystem USB LAN78XX ETHERNET DRIVER
Changes 35 / 91 (38%)
(No activity)
Top reviewers:
[23]: andrew@lunn.ch
[3]: horms@kernel.org
[2]: mateusz.polchlopek@intel.com
INACTIVE MAINTAINER Woojung Huh <woojung.huh@microchip.com>
Move Woojung to CREDITS and add new maintainers who are more
likely to review LAN78xx patches.
Jakub Kicinski [Wed, 8 Jan 2025 15:52:35 +0000 (07:52 -0800)]
MAINTAINERS: mark Synopsys DW XPCS as Orphan
There's not much review support from Jose, there is a sharp
drop in his participation around 4 years ago.
The DW XPCS IP is very popular and the driver requires active
maintenance.
gitdm missingmaints says:
Subsystem SYNOPSYS DESIGNWARE ETHERNET XPCS DRIVER
Changes 33 / 94 (35%)
(No activity)
Top reviewers:
[16]: andrew@lunn.ch
[12]: vladimir.oltean@nxp.com
[2]: f.fainelli@gmail.com
INACTIVE MAINTAINER Jose Abreu <Jose.Abreu@synopsys.com>
Chenguang Zhao [Wed, 8 Jan 2025 03:00:09 +0000 (11:00 +0800)]
net/mlx5: Fix variable not being completed when function returns
When cmd_alloc_index(), fails cmd_work_handler() needs
to complete ent->slotted before returning early.
Otherwise the task which issued the command may hang:
mlx5_core 0000:01:00.0: cmd_work_handler:877:(pid 3880418): failed to allocate command entry
INFO: task kworker/13:2:4055883 blocked for more than 120 seconds.
Not tainted 4.19.90-25.44.v2101.ky10.aarch64 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/13:2 D 0 4055883 2 0x00000228
Workqueue: events mlx5e_tx_dim_work [mlx5_core]
Call trace:
__switch_to+0xe8/0x150
__schedule+0x2a8/0x9b8
schedule+0x2c/0x88
schedule_timeout+0x204/0x478
wait_for_common+0x154/0x250
wait_for_completion+0x28/0x38
cmd_exec+0x7a0/0xa00 [mlx5_core]
mlx5_cmd_exec+0x54/0x80 [mlx5_core]
mlx5_core_modify_cq+0x6c/0x80 [mlx5_core]
mlx5_core_modify_cq_moderation+0xa0/0xb8 [mlx5_core]
mlx5e_tx_dim_work+0x54/0x68 [mlx5_core]
process_one_work+0x1b0/0x448
worker_thread+0x54/0x468
kthread+0x134/0x138
ret_from_fork+0x10/0x18
Fixes: 485d65e13571 ("net/mlx5: Add a timeout to acquire the command queue semaphore") Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Acked-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20250108030009.68520-1-zhaochenguang@kylinos.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Wed, 8 Jan 2025 09:15:53 +0000 (12:15 +0300)]
rtase: Fix a check for error in rtase_alloc_msix()
The pci_irq_vector() function never returns zero. It returns negative
error codes or a positive non-zero IRQ number. Fix the error checking to
test for negatives.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Link: https://patch.msgid.link/f2ecc88d-af13-4651-9820-7cc665230019@stanley.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Parker Newman [Tue, 7 Jan 2025 21:24:59 +0000 (16:24 -0500)]
net: stmmac: dwmac-tegra: Read iommu stream id from device tree
Nvidia's Tegra MGBE controllers require the IOMMU "Stream ID" (SID) to be
written to the MGBE_WRAP_AXI_ASID0_CTRL register.
The current driver is hard coded to use MGBE0's SID for all controllers.
This causes softirq time outs and kernel panics when using controllers
other than MGBE0.
Example dmesg errors when an ethernet cable is connected to MGBE1:
This bug has existed since the dwmac-tegra driver was added in Dec 2022
(See Fixes tag below for commit hash).
The Tegra234 SOC has 4 MGBE controllers, however Nvidia's Developer Kit
only uses MGBE0 which is why the bug was not found previously. Connect Tech
has many products that use 2 (or more) MGBE controllers.
The solution is to read the controller's SID from the existing "iommus"
device tree property. The 2nd field of the "iommus" device tree property
is the controller's SID.
Device tree snippet from tegra234.dtsi showing MGBE1's "iommus" property:
Nvidia's arm-smmu driver reads the "iommus" property and stores the SID in
the MGBE device's "fwspec" struct. The dwmac-tegra driver can access the
SID using the tegra_dev_iommu_get_stream_id() helper function found in
linux/iommu.h.
Calling tegra_dev_iommu_get_stream_id() should not fail unless the "iommus"
property is removed from the device tree or the IOMMU is disabled.
While the Tegra234 SOC technically supports bypassing the IOMMU, it is not
supported by the current firmware, has not been tested and not recommended.
More detailed discussion with Thierry Reding from Nvidia linked below.
Even though we fixed a logic error in the commit cited below, syzbot
still managed to trigger an underflow of the per-host bulk flow
counters, leading to an out of bounds memory access.
To avoid any such logic errors causing out of bounds memory accesses,
this commit factors out all accesses to the per-host bulk flow counters
to a series of helpers that perform bounds-checking before any
increments and decrements. This also has the benefit of improving
readability by moving the conditional checks for the flow mode into
these helpers, instead of having them spread out throughout the
code (which was the cause of the original logic error).
As part of this change, the flow quantum calculation is consolidated
into a helper function, which means that the dithering applied to the
ost load scaling is now applied both in the DRR rotation and when a
sparse flow's quantum is first initiated. The only user-visible effect
of this is that the maximum packet size that can be sent while a flow
stays sparse will now vary with +/- one byte in some cases. This should
not make a noticeable difference in practice, and thus it's not worth
complicating the code to preserve the old behaviour.
Fixes: 546ea84d07e3 ("sched: sch_cake: fix bulk flow accounting logic for host fairness") Reported-by: syzbot+f63600d288bfb7057424@syzkaller.appspotmail.com Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Dave Taht <dave.taht@gmail.com> Link: https://patch.msgid.link/20250107120105.70685-1-toke@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
net: make sure we retain NAPI ordering on netdev->napi_list
I promised Eric to remove the rtnl protection of the NAPI list,
when I sat down to implement it over the break I realized that
the recently added NAPI ID retention will break the list ordering
assumption we have in netlink dump. The ordering used to happen
"naturally", because we'd always add NAPIs that the head of the
list, and assign a new monotonically increasing ID.
Before the first patch of this series we'd still only add at
the head of the list but now the newly added NAPI may inherit
from its config an ID lower than something else already on the list.
The fix is in the first patch, the rest is netdevsim churn to test it.
I'm posting this for net-next, because AFAICT the problem can't
be triggered in net, given the very limited queue API adoption.
v2:
- [patch 2] allocate the array with kcalloc() instead of kvcalloc()
- [patch 2] set GFP_KERNEL_ACCOUNT when allocating queues
- [patch 6] don't null-check page pool before page_pool_destroy()
- [patch 6] controled -> controlled
- [patch 7] change mode to 0200
- [patch 7] reorder removal to be inverse of add
- [patch 7] fix the spaces vs tabs
v1: https://lore.kernel.org/20250103185954.1236510-1-kuba@kernel.org
====================
Jakub Kicinski [Tue, 7 Jan 2025 16:08:46 +0000 (08:08 -0800)]
selftests: net: test listing NAPI vs queue resets
Test listing netdevsim NAPIs before and after a single queue
has been reset (and NAPIs re-added).
Start from resetting the middle queue because edge cases
(first / last) may actually be less likely to trigger bugs.
# ./tools/testing/selftests/net/nl_netdev.py
KTAP version 1
1..4
ok 1 nl_netdev.empty_check
ok 2 nl_netdev.lo_check
ok 3 nl_netdev.page_pool_check
ok 4 nl_netdev.napi_list_check
# Totals: pass:4 fail:0 xfail:0 xpass:0 skip:0 error:0
Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Stanislav Fomichev <sdf@fomichev.me> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 7 Jan 2025 16:08:45 +0000 (08:08 -0800)]
netdevsim: add debugfs-triggered queue reset
Support triggering queue reset via debugfs for an upcoming test.
Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Stanislav Fomichev <sdf@fomichev.me> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Mina Almasry <almasrymina@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 7 Jan 2025 16:08:44 +0000 (08:08 -0800)]
netdevsim: add queue management API support
Add queue management API support. We need a way to reset queues
to test NAPI reordering, the queue management API provides a
handy scaffolding for that.
Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Stanislav Fomichev <sdf@fomichev.me> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Mina Almasry <almasrymina@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 7 Jan 2025 16:08:43 +0000 (08:08 -0800)]
netdevsim: add queue alloc/free helpers
We'll need the code to allocate and free queues in the queue management
API, factor it out.
Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 7 Jan 2025 16:08:42 +0000 (08:08 -0800)]
netdevsim: allocate rqs individually
Make nsim->rqs an array of pointers and allocate them individually
so that we can swap them out one by one.
Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 7 Jan 2025 16:08:41 +0000 (08:08 -0800)]
netdevsim: support NAPI config
Link the NAPI instances to their configs. This will be needed to test
that NAPI config doesn't break list ordering.
Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 7 Jan 2025 16:08:40 +0000 (08:08 -0800)]
netdev: define NETDEV_INTERNAL
Linus suggested during one of past maintainer summits (in context of
a DMA_BUF discussion) that symbol namespaces can be used to prevent
unwelcome but in-tree code from using all exported functions.
Create a namespace for netdev.
Export netdev_rx_queue_restart(), drivers may want to use it since
it gives them a simple and safe way to restart a queue to apply
config changes. But it's both too low level and too actively developed
to be used outside netdev.
Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 7 Jan 2025 16:08:39 +0000 (08:08 -0800)]
net: make sure we retain NAPI ordering on netdev->napi_list
Netlink code depends on NAPI instances being sorted by ID on
the netdev list for dump continuation. We need to be able to
find the position on the list where we left off if dump does
not fit in a single skb, and in the meantime NAPI instances
can come and go.
This was trivially true when we were assigning a new ID to every
new NAPI instance. Since we added the NAPI config API, we try
to retain the ID previously used for the same queue, but still
add the new NAPI instance at the start of the list.
This is fine if we reset the entire netdev and all NAPIs get
removed and added back. If driver replaces a NAPI instance
during an operation like DEVMEM queue reset, or recreates
a subset of NAPI instances in other ways we may end up with
broken ordering, and therefore Netlink dumps with either
missing or duplicated entries.
At this stage the problem is theoretical. Only two drivers
support queue API, bnxt and gve. gve recreates NAPIs during
queue reset, but it doesn't support NAPI config.
bnxt supports NAPI config but doesn't recreate instances
during reset.
We need to save the ID in the config as soon as it is assigned
because otherwise the new NAPI will not know what ID it will
get at enable time, at the time it is being added.
Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pablo Neira Ayuso [Wed, 8 Jan 2025 21:56:33 +0000 (22:56 +0100)]
netfilter: conntrack: clamp maximum hashtable size to INT_MAX
Use INT_MAX as maximum size for the conntrack hashtable. Otherwise, it
is possible to hit WARN_ON_ONCE in __kvmalloc_node_noprof() when
resizing hashtable because __GFP_NOWARN is unset. See:
0708a0afe291 ("mm: Consider __GFP_NOWARN flag for oversized kvmalloc() calls")
Note: hashtable resize is only possible from init_netns.
Fixes: 9cc1c73ad666 ("netfilter: conntrack: avoid integer overflow when resizing") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
projects / users / hch / misc.git / log