When the slave address is written in do_start(), SLAVE_ADDR is written
completely. This may overwrite some setting related to the clock rate
or signal filtering.
Fix this by writing only the bits related to slave address. To avoid
causing unexpected changed, explicitly disable filtering or high/low
clock mode which may have been left over by the bootloader.
Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On setxattr() syscall path due to an apprent typo the size of a dynamically
allocated memory chunk for storing struct smb2_file_full_ea_info object is
computed incorrectly, to be more precise the first addend is the size of
a pointer instead of the wanted object size. Coincidentally it makes no
difference on 64-bit platforms, however on 32-bit targets the following
memcpy() writes 4 bytes of data outside of the dynamically allocated memory.
Disabling lock debugging due to kernel taint
INFO: 0x79e69a6f-0x9e5cdecf @offset=368. First byte 0x73 instead of 0xcc
INFO: Slab 0xd36d2454 objects=85 used=51 fp=0xf7d0fc7a flags=0x35000201
INFO: Object 0x6f171df3 @offset=352 fp=0x00000000
Redzone 5d4ff02d: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 6f171df3: 00 00 00 00 00 05 06 00 73 6e 72 75 62 00 66 69 ........snrub.fi
Redzone 79e69a6f: 73 68 32 0a sh2.
Padding 56254d82: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 0 PID: 8196 Comm: attr Tainted: G B 5.9.0-rc8+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
Call Trace:
dump_stack+0x54/0x6e
print_trailer+0x12c/0x134
check_bytes_and_report.cold+0x3e/0x69
check_object+0x18c/0x250
free_debug_processing+0xfe/0x230
__slab_free+0x1c0/0x300
kfree+0x1d3/0x220
smb2_set_ea+0x27d/0x540
cifs_xattr_set+0x57f/0x620
__vfs_setxattr+0x4e/0x60
__vfs_setxattr_noperm+0x4e/0x100
__vfs_setxattr_locked+0xae/0xd0
vfs_setxattr+0x4e/0xe0
setxattr+0x12c/0x1a0
path_setxattr+0xa4/0xc0
__ia32_sys_lsetxattr+0x1d/0x20
__do_fast_syscall_32+0x40/0x70
do_fast_syscall_32+0x29/0x60
do_SYSENTER_32+0x15/0x20
entry_SYSENTER_32+0x9f/0xf2
Fixes: 5517554e4313 ("cifs: Add support for writing attributes on SMB2+") Signed-off-by: Vladimir Zapolskiy <vladimir@tuxera.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xfrm interfaces currently test for !skb->ignore_df when deciding
whether to update the pmtu on the skb's dst. Because of this, no pmtu
exception is created when we do something like:
ping -s 1438 <dest>
By dropping this check, the pmtu exception will be created and the
next ping attempt will work.
Currently nvme_tcp_try_send_data() doesn't use kernel_sendpage() to
send slab pages. But for pages allocated by __get_free_pages() without
__GFP_COMP, which also have refcount as 0, they are still sent by
kernel_sendpage() to remote end, this is problematic.
The new introduced helper sendpage_ok() checks both PageSlab tag and
page_count counter, and returns true if the checking page is OK to be
sent by kernel_sendpage().
This patch fixes the page checking issue of nvme_tcp_try_send_data()
with sendpage_ok(). If sendpage_ok() returns true, send this page by
kernel_sendpage(), otherwise use sock_no_sendpage to handle this page.
Signed-off-by: Coly Li <colyli@suse.de> Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Jan Kara <jack@suse.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com> Cc: Philipp Reisner <philipp.reisner@linbit.com> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Vlastimil Babka <vbabka@suse.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a10674bf2406 ("tcp: detecting the misuse of .sendpage for Slab
objects") adds the checks for Slab pages, but the pages don't have
page_count are still missing from the check.
Network layer's sendpage method is not designed to send page_count 0
pages neither, therefore both PageSlab() and page_count() should be
both checked for the sending page. This is exactly what sendpage_ok()
does.
This patch uses sendpage_ok() in do_tcp_sendpages() to detect misused
.sendpage, to make the code more robust.
Fixes: a10674bf2406 ("tcp: detecting the misuse of .sendpage for Slab objects") Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Coly Li <colyli@suse.de> Cc: Vasily Averin <vvs@virtuozzo.com> Cc: David S. Miller <davem@davemloft.net> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original problem was from nvme-over-tcp code, who mistakenly uses
kernel_sendpage() to send pages allocated by __get_free_pages() without
__GFP_COMP flag. Such pages don't have refcount (page_count is 0) on
tail pages, sending them by kernel_sendpage() may trigger a kernel panic
from a corrupted kernel heap, because these pages are incorrectly freed
in network stack as page_count 0 pages.
This patch introduces a helper sendpage_ok(), it returns true if the
checking page,
- is not slab page: PageSlab(page) is false.
- has page refcount: page_count(page) is not zero
All drivers who want to send page to remote end by kernel_sendpage()
may use this helper to check whether the page is OK. If the helper does
not return true, the driver should try other non sendpage method (e.g.
sock_no_sendpage()) to handle the page.
Signed-off-by: Coly Li <colyli@suse.de> Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Jan Kara <jack@suse.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com> Cc: Philipp Reisner <philipp.reisner@linbit.com> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Vlastimil Babka <vbabka@suse.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been elusive reports of filemap_fault() hitting its
VM_BUG_ON_PAGE(page_to_pgoff(page) != offset, page) on kernels built
with CONFIG_READ_ONLY_THP_FOR_FS=y.
Suren has hit it on a kernel with CONFIG_READ_ONLY_THP_FOR_FS=y and
CONFIG_NUMA is not set: and he has analyzed it down to how khugepaged
without NUMA reuses the same huge page after collapse_file() failed
(whereas NUMA targets its allocation to the respective node each time).
And most of us were usually testing with CONFIG_NUMA=y kernels.
An initial patch replaced __SetPageLocked() by lock_page(), which did
fix the race which Suren illustrates above. But testing showed that it's
not good enough: if the racing task's __lock_page() gets delayed long
after its find_get_page(), then it may follow collapse_file(new start)'s
successful final unlock_page(), and crash on the same VM_BUG_ON_PAGE.
It could be fixed by relaxing filemap_fault()'s VM_BUG_ON_PAGE to a
check and retry (as is done for mapping), with similar relaxations in
find_lock_entry() and pagecache_get_page(): but it's not obvious what
else might get caught out; and khugepaged non-NUMA appears to be unique
in exposing a page to page cache, then revoking, without going through
a full cycle of freeing before reuse.
Instead, non-NUMA khugepaged_prealloc_page() release the old page
if anyone else has a reference to it (1% of cases when I tested).
Although never reported on huge tmpfs, I believe its find_lock_entry()
has been at similar risk; but huge tmpfs does not rely on khugepaged
for its normal working nearly so much as READ_ONLY_THP_FOR_FS does.
De-referencing skb after call to gro_cells_receive() is not allowed.
We need to fetch skb->len earlier.
Fixes: 5491e7c6b1a9 ("macsec: enable GRO and RPS on macsec devices") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[CAUSE]
Because btrfs_truncate_block() always reserves space without checking
the NOCOW attribute.
Since the writeback path follows NOCOW bit, we only need to bother the
space reservation code in btrfs_truncate_block().
[FIX]
Make btrfs_truncate_block() follow btrfs_buffered_write() to try to
reserve data space first, and fall back to NOCOW check only when we
don't have enough space.
Such always-try-reserve is an optimization introduced in
btrfs_buffered_write(), to avoid expensive btrfs_check_can_nocow() call.
This patch will export check_can_nocow() as btrfs_check_can_nocow(), and
use it in btrfs_truncate_block() to fix the problem.
Reported-by: Martin Doucha <martin.doucha@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we attempt to do a RWF_NOWAIT write against a file range for which we
can only do NOCOW for a part of it, due to the existence of holes or
shared extents for example, we proceed with the write as if it were
possible to NOCOW the whole range.
Example:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ touch /mnt/sdj/bar
$ chattr +C /mnt/sdj/bar
$ xfs_io -d -c "pwrite -S 0xab -b 256K 0 256K" /mnt/bar
wrote 262144/262144 bytes at offset 0
256 KiB, 1 ops; 0.0003 sec (694.444 MiB/sec and 2777.7778 ops/sec)
This last write should fail with -EAGAIN since the file range from 64K to
128K is a hole. On xfs it fails, as expected, but on ext4 it currently
succeeds because apparently it is expensive to check if there are extents
allocated for the whole range, but I'll check with the ext4 people.
Fix the issue by checking if check_can_nocow() returns a number of
NOCOW'able bytes smaller then the requested number of bytes, and if it
does return -EAGAIN.
Fixes: edf064e7c6fec3 ("btrfs: nowait aio support") CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
When deleting large files (which cross block group boundary) with
discard mount option, we find some btrfs_discard_extent() calls only
trimmed part of its space, not the whole range:
type: bbio->map_type, in above case, it's SINGLE DATA.
start: Logical address of this trim
len: Logical length of this trim
trimmed: Physically trimmed bytes
ratio: trimmed / len
Thus leaving some unused space not discarded.
[CAUSE]
When discard mount option is specified, after a transaction is fully
committed (super block written to disk), we begin to cleanup pinned
extents in the following call chain:
However, pinned extents are recorded in an extent_io_tree, which can
merge adjacent extent states.
When a large file gets deleted and it has adjacent file extents across
block group boundary, we will get a large merged range like this:
|<--- BG1 --->|<--- BG2 --->|
|//////|<-- Range to discard --->|/////|
To discard that range, we have the following calls:
btrfs_discard_extent()
|- btrfs_map_block()
| Returned bbio will end at BG1's end. As btrfs_map_block()
| never returns result across block group boundary.
|- btrfs_issuse_discard()
Issue discard for each stripe.
So we will only discard the range in BG1, not the remaining part in BG2.
Furthermore, this bug is not that reliably observed, for above case, if
there is no other extent in BG2, BG2 will be empty and btrfs will trim
all space of BG2, covering up the bug.
[FIX]
- Allow __btrfs_map_block_for_discard() to modify @length parameter
btrfs_map_block() uses its @length paramter to notify the caller how
many bytes are mapped in current call.
With __btrfs_map_block_for_discard() also modifing the @length,
btrfs_discard_extent() now understands when to do extra trim.
- Call btrfs_map_block() in a loop until we hit the range end Since we
now know how many bytes are mapped each time, we can iterate through
each block group boundary and issue correct trim for each range.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Tested-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing an incremental send and a file has extents shared with itself
at different file offsets, it's possible for send to emit clone operations
that will fail at the destination because the source range goes beyond the
file's current size. This happens when the file size has increased in the
send snapshot, there is a hole between the shared extents and both shared
extents are at file offsets which are greater the file's size in the
parent snapshot.
Example:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt/sdb
# Clone part of that 320K extent into a lower file offset (192K).
# This file offset is greater than the file's size in the parent
# snapshot (64K). Also the clone range is a bit behind the offset of
# the 320K extent so that we leave a hole between the shared extents.
$ xfs_io -c "reflink /mnt/sdb/foobar 448K 192K 192K" /mnt/sdb/foobar
The problem is that after processing the extent at file offset 256K, which
refers to the first 128K of the 320K extent created by the buffered write
operations, we have 'cur_inode_next_write_offset' set to 384K, which
corresponds to the end offset of the partially shared extent (256K + 128K)
and to the current file size in the receiver. Then when we process the
extent at offset 512K, we do extent backreference iteration to figure out
if we can clone the extent from some other inode or from the same inode,
and we consider the extent at offset 256K of the same inode as a valid
source for a clone operation, which is not correct because at that point
the current file size in the receiver is 384K, which corresponds to the
end of last processed extent (at file offset 256K), so using a clone
source range from 256K to 256K + 320K is invalid because that goes past
the current size of the file (384K) - this makes the receiver get an
-EINVAL error when attempting the clone operation.
So fix this by excluding clone sources that have a range that goes beyond
the current file size in the receiver when iterating extent backreferences.
A test case for fstests follows soon.
Fixes: 11f2069c113e02 ("Btrfs: send, allow clone operations within the same file") CC: stable@vger.kernel.org # 5.5+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For send we currently skip clone operations when the source and
destination files are the same. This is so because clone didn't support
this case in its early days, but support for it was added back in May
2013 by commit a96fbc72884fcb ("Btrfs: allow file data clone within a
file"). This change adds support for it.
Example:
$ mkfs.btrfs -f /dev/sdd
$ mount /dev/sdd /mnt/sdd
By default, PCI drivers with runtime PM enabled will skip the calls
to suspend and resume on system PM. For this driver, we don't want
that, as we need to perform additional steps for system PM to work
properly on all systems. So instruct the PM core to not skip these
calls.
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM") Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com> Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org>
[iwamatsu: Use DPM_FLAG_NEVER_SKIP instead of DPM_FLAG_NO_DIRECT_COMPLETE] Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since glibc 2.28 when running 'perf top --stdio', input handling no
longer works, but hitting any key always just prints the "Mapped keys"
help text.
To fix it, call clearerr() in the display_thread() loop to clear any EOF
sticky errors, as instructed in the glibc NEWS file
(https://sourceware.org/git/?p=glibc.git;a=blob;f=NEWS):
* All stdio functions now treat end-of-file as a sticky condition. If you
read from a file until EOF, and then the file is enlarged by another
process, you must call clearerr or another function with the same effect
(e.g. fseek, rewind) before you can read the additional data. This
corrects a longstanding C99 conformance bug. It is most likely to affect
programs that use stdio to read interactive input from a terminal.
(Bug #1190.)
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20200305083714.9381-2-tommi.t.rantala@nokia.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2d4f27999b88 ("perf data: Add global path holder") missed path
conversion in tests/topology.c, causing the "Session topology" testcase
to "hang" (waits forever for input from stdin) when doing "ssh $VM perf
test".
Can be reproduced by running "cat | perf test topo", and crashed by
replacing cat with true:
$ true | perf test -v topo
40: Session topology :
--- start ---
test child forked, pid 3638
templ file: /tmp/perf-test-QPvAch
incompatible file format
incompatible file format (rerun with -v to learn more)
free(): invalid pointer
test child interrupted
---- end ----
Session topology: FAILED!
Committer testing:
Reproduced the above result before the patch and after it is back
working:
# true | perf test -v topo
41: Session topology :
--- start ---
test child forked, pid 19374
templ file: /tmp/perf-test-YOTEQg
CPU 0, core 0, socket 0
CPU 1, core 1, socket 0
CPU 2, core 2, socket 0
CPU 3, core 3, socket 0
CPU 4, core 0, socket 0
CPU 5, core 1, socket 0
CPU 6, core 2, socket 0
CPU 7, core 3, socket 0
test child finished with 0
---- end ----
Session topology: Ok
#
Fixes: 2d4f27999b88 ("perf data: Add global path holder") Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Mamatha Inamdar <mamatha4@linux.vnet.ibm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Link: http://lore.kernel.org/lkml/20200423115341.562782-1-tommi.t.rantala@nokia.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting hung task in wait_for_device_probe() [1]. At least,
we always need to decrement probe_count if we incremented probe_count in
really_probe().
However, since I can't find "Resources present before probing" message in
the console log, both "this message simply flowed off" and "syzbot is not
hitting this path" will be possible. Therefore, while we are at it, let's
also prepare for concurrent wait_for_device_probe() calls by replacing
wake_up() with wake_up_all().
Evaluating ACPI _BCL could fail, then ACPI buffer size will be set to 0.
When reuse this ACPI buffer, AE_BUFFER_OVERFLOW will be triggered.
Re-initialize buffer size will make ACPI evaluate successfully.
Fixes: 46445b6b896fd ("thinkpad-acpi: fix handle locate for video and query of _BCL") Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 recent commits: cfae58ed681c ("platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE
on the 9 / "Laptop" chasis-type") 1fac39fd0316 ("platform/x86: intel-vbtn: Also handle tablet-mode switch on
"Detachable" and "Portable" chassis-types")
Enabled reporting of SW_TABLET_MODE on more devices since the vbtn ACPI
interface is used by the firmware on some of those devices to report this.
Testing has shown that unconditionally enabling SW_TABLET_MODE reporting
on all devices with a chassis type of 8 ("Portable") or 10 ("Notebook")
which support the VGBS method is a very bad idea.
Many of these devices are normal laptops (non 2-in-1) models with a VGBS
which always returns 0, which we translate to SW_TABLET_MODE=1. This in
turn causes userspace (libinput) to suppress events from the builtin
keyboard and touchpad, making the laptop essentially unusable.
Since the problem of wrongly reporting SW_TABLET_MODE=1 in combination
with libinput, leads to a non-usable system. Where as OTOH many people will
not even notice when SW_TABLET_MODE is not being reported, this commit
changes intel_vbtn_has_switches() to use a DMI based allow-list.
The new DMI based allow-list matches on the 31 ("Convertible") and
32 ("Detachable") chassis-types, as these clearly are 2-in-1s and
so far if they support the intel-vbtn ACPI interface they all have
properly working SW_TABLET_MODE reporting.
Besides these 2 generic matches, it also contains model specific matches
for 2-in-1 models which use a different chassis-type and which are known
to have properly working SW_TABLET_MODE reporting.
This has been tested on the following 2-in-1 devices:
Dell Venue 11 Pro 7130 vPro
HP Pavilion X2 10-p002nd
HP Stream x360 Convertible PC 11
Medion E1239T
Systems with memory or disk constraints often reduce the kernel footprint
by configuring LD_DEAD_CODE_DATA_ELIMINATION. However, this can result in
removal of any BTF information.
Use the KEEP() macro to preserve the BTF data as done with other important
sections, while still allowing for smaller kernels.
Fixes: 90ceddcb4950 ("bpf: Support llvm-objcopy for vmlinux BTF") Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/a635b5d3e2da044e7b51ec1315e8910fbce0083f.1600417359.git.Tony.Ambardar@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This situation was first observed with kernel 5.4.x, cross-compiled for a
MIPS target system. Fix by adding a sanity-check for export of zero-length
data sections.
Fixes: 341dfcf8d78e ("btf: expose BTF info through sysfs") Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/b38db205a66238f70823039a8c531535864eaac5.1600417359.git.Tony.Ambardar@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang static analysis flags this represenative problem
thinkpad_acpi.c:2523:7: warning: Branch condition evaluates
to a garbage value
if (!oldn->mute ||
^~~~~~~~~~~
In hotkey_kthread() mute is conditionally set by hotkey_read_nvram()
but unconditionally checked by hotkey_compare_and_issue_event().
So the tp_nvram_state variable s[2] needs to be initialized.
Fixes: 01e88f25985d ("ACPI: thinkpad-acpi: add CMOS NVRAM polling for hot keys (v9)") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: mark gross <mgross@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cfae58ed681c ("platform/x86: intel-vbtn: Only blacklist
SW_TABLET_MODE on the 9 / "Laptop" chasis-type") restored SW_TABLET_MODE
reporting on the HP stream x360 11 series on which it was previously broken
by commit de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet
mode switch on 2-in-1's").
It turns out that enabling SW_TABLET_MODE reporting on devices with a
chassis-type of 10 ("Notebook") causes SW_TABLET_MODE to always report 1
at boot on the HP Pavilion 11 x360, which causes libinput to disable the
kbd and touchpad.
The HP Pavilion 11 x360's ACPI VGBS method sets bit 4 instead of bit 6 when
NOT in tablet mode at boot. Inspecting all the DSDTs in my DSDT collection
shows only one other model, the Medion E1239T ever setting bit 4 and it
always sets this together with bit 6.
So lets treat bit 4 as a second bit which when set indicates the device not
being in tablet-mode, as we already do for bit 6.
While at it also prefix all VGBS constant defines with "VGBS_".
Fixes: cfae58ed681c ("platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mark Gross <mgross@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When devm_regulator_register() fails, ec should be
freed just like when olpc_ec_cmd() fails.
Fixes: 231c0c216172a ("Platform: OLPC: Add a regulator for the DCON") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel threads intentionally do CLONE_FS in order to follow any changes
that 'init' does to set up the root directory (or cwd).
It is admittedly a bit odd, but it avoids the situation where 'init'
does some extensive setup to initialize the system environment, and then
we execute a usermode helper program, and it uses the original FS setup
from boot time that may be very limited and incomplete.
[ Both Al Viro and Eric Biederman point out that 'pivot_root()' will
follow the root regardless, since it fixes up other users of root (see
chroot_fs_refs() for details), but overmounting root and doing a
chroot() would not. ]
However, Vegard Nossum noticed that the CLONE_FS not only means that we
follow the root and current working directories, it also means we share
umask with whatever init changed it to. That wasn't intentional.
Just reset umask to the original default (0022) before actually starting
the usermode helper program.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The open-coded computation of the used size doesn't take the event
into account when the VIRTIO_RING_F_EVENT_IDX feature is present.
Fix that by using vhost_get_used_size().
When the IOTLB device is enabled, the vring addresses we get
from userspace are GIOVAs. It is thus wrong to pass them down
to access_ok() which only takes HVAs.
Access validation is done at prefetch time with IOTLB. Teach
vq_access_ok() about that by moving the (vq->iotlb) check
from vhost_vq_access_ok() to vq_access_ok(). This prevents
vhost_vring_set_addr() to fail when verifying the accesses.
No behavior change for vhost_vq_access_ok().
In nl80211_parse_key(), key.idx is first initialized as -1.
If this value of key.idx remains unmodified and gets returned, and
nl80211_key_allowed() also returns 0, then rdev_del_key() gets called
with key.idx = -1.
This causes an out-of-bounds array access.
Handle this issue by checking if the value of key.idx after
nl80211_parse_key() is called and return -EINVAL if key.idx < 0.
Muchun Song [Wed, 7 Oct 2020 03:16:34 +0000 (11:16 +0800)]
io_uring: Fix remove irrelevant req from the task_list
If the process 0 has been initialized io_uring is complete, and
then fork process 1. If process 1 exits and it leads to delete
all reqs from the task_list. If we kill process 0. We will not
send SIGINT signal to the kworker. So we can not remove the req
from the task_list. The io_sq_wq_submit_work() can do that for
us.
Fixes: 1c4404efcf2c ("io_uring: make sure async workqueue is canceled on exit") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Muchun Song [Wed, 7 Oct 2020 03:16:33 +0000 (11:16 +0800)]
io_uring: Fix missing smp_mb() in io_cancel_async_work()
The store to req->flags and load req->work_task should not be
reordering in io_cancel_async_work(). We should make sure that
either we store REQ_F_CANCE flag to req->flags or we see the
req->work_task setted in io_sq_wq_submit_work().
Fixes: 1c4404efcf2c ("io_uring: make sure async workqueue is canceled on exit") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yinyin Zhu [Wed, 7 Oct 2020 03:16:32 +0000 (11:16 +0800)]
io_uring: Fix resource leaking when kill the process
The commit
1c4404efcf2c0> ("<io_uring: make sure async workqueue is canceled on exit>")
doesn't solve the resource leak problem totally! When kworker is doing a
io task for the io_uring, The process which submitted the io task has
received a SIGKILL signal from the user. Then the io_cancel_async_work
function could have sent a SIGINT signal to the kworker, but the judging
condition is wrong. So it doesn't send a SIGINT signal to the kworker,
then caused the resource leaking problem.
Why the juding condition is wrong? The process is a multi-threaded process,
we call the thread of the process which has submitted the io task Thread1.
So the req->task is the current macro of the Thread1. when all the threads
of the process have done exit procedure, the last thread will call the
io_cancel_async_work, but the last thread may not the Thread1, so the task
is not equal and doesn't send the SIGINT signal. To fix this bug, we alter
the task attribute of the req with struct files_struct. And check the files
instead.
Fixes: 1c4404efcf2c0 ("io_uring: make sure async workqueue is canceled on exit") Signed-off-by: Yinyin Zhu <zhuyinyin@bytedance.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:
Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425abd65b5 ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fbcon_get_font() is reading out-of-bounds. A malicious user may resize
`vc->vc_font.height` to a large value, causing fbcon_get_font() to
read out of `fontdata`.
fbcon_get_font() handles both built-in and user-provided fonts.
Fortunately, recently we have added FONT_EXTRA_WORDS support for built-in
fonts, so fix it by adding range checks using FNTSIZE().
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h", and patch "Fonts: Support FONT_EXTRA_WORDS
macros for built-in fonts".
syzbot has reported an issue in the framebuffer layer, where a malicious
user may overflow our built-in font data buffers.
In order to perform a reliable range check, subsystems need to know
`FONTDATAMAX` for each built-in font. Unfortunately, our font descriptor,
`struct console_font` does not contain `FONTDATAMAX`, and is part of the
UAPI, making it infeasible to modify it.
For user-provided fonts, the framebuffer layer resolves this issue by
reserving four extra words at the beginning of data buffers. Later,
whenever a function needs to access them, it simply uses the following
macros:
Recently we have gathered all the above macros to <linux/font.h>. Let us
do the same thing for built-in fonts, prepend four extra words (including
`FONTDATAMAX`) to their data buffers, so that subsystems can use these
macros for all fonts, no matter built-in or user-provided.
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h".
drivers/video/console/newport_con.c is borrowing FONT_EXTRA_WORDS macros
from drivers/video/fbdev/core/fbcon.h. To keep things simple, move all
definitions into <linux/font.h>.
Since newport_con now uses four extra words, initialize the fourth word in
newport_set_font() properly.
The indexes to the nf_nat_l[34]protos arrays come from userspace. So
check the tuple's family, e.g. l3num, when creating the conntrack in
order to prevent an OOB memory access during setup. Here is an example
kernel panic on 4.14.180 when userspace passes in an index greater than
NFPROTO_NUMPROTO.
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:...
Process poc (pid: 5614, stack limit = 0x00000000a3933121)
CPU: 4 PID: 5614 Comm: poc Tainted: G S W O 4.14.180-g051355490483
Hardware name: Qualcomm Technologies, Inc. SM8150 V2 PM8150 Google Inc. MSM
task: 000000002a3dfffe task.stack: 00000000a3933121
pc : __cfi_check_fail+0x1c/0x24
lr : __cfi_check_fail+0x1c/0x24
...
Call trace:
__cfi_check_fail+0x1c/0x24
name_to_dev_t+0x0/0x468
nfnetlink_parse_nat_setup+0x234/0x258
ctnetlink_parse_nat_setup+0x4c/0x228
ctnetlink_new_conntrack+0x590/0xc40
nfnetlink_rcv_msg+0x31c/0x4d4
netlink_rcv_skb+0x100/0x184
nfnetlink_rcv+0xf4/0x180
netlink_unicast+0x360/0x770
netlink_sendmsg+0x5a0/0x6a4
___sys_sendmsg+0x314/0x46c
SyS_sendmsg+0xb4/0x108
el0_svc_naked+0x34/0x38
This crash is not happening since 5.4+, however, ctnetlink still
allows for creating entries with unsupported layer 3 protocol number.
Fixes: c1d10adb4a521 ("[NETFILTER]: Add ctnetlink port for nf_conntrack") Signed-off-by: Will McVicker <willmcvicker@google.com>
[pablo@netfilter.org: rebased original patch on top of nf.git] Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking for the lack of epitems refering to the epoll we want to insert into
is not enough; we might have an insertion of that epoll into another one that
has already collected the set of files to recheck for excessive reverse paths,
but hasn't gotten to creating/inserting the epitem for it.
However, any such insertion in progress can be detected - it will update the
generation count in our epoll when it's done looking through it for files
to check. That gets done under ->mtx of our epoll and that allows us to
detect that safely.
We are *not* holding epmutex here, so the generation count is not stable.
However, since both the update of ep->gen by loop check and (later)
insertion into ->f_ep_link are done with ep->mtx held, we are fine -
the sequence is
grab epmutex
bump loop_check_gen
...
grab tep->mtx // 1
tep->gen = loop_check_gen
...
drop tep->mtx // 2
...
grab tep->mtx // 3
...
insert into ->f_ep_link
...
drop tep->mtx // 4
bump loop_check_gen
drop epmutex
and if the fastpath check in another thread happens for that
eventpoll, it can come
* before (1) - in that case fastpath is just fine
* after (4) - we'll see non-empty ->f_ep_link, slow path
taken
* between (2) and (3) - loop_check_gen is stable,
with ->mtx providing barriers and we end up taking slow path.
Note that ->f_ep_link emptiness check is slightly racy - we are protected
against insertions into that list, but removals can happen right under us.
Not a problem - in the worst case we'll end up taking a slow path for
no good reason.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the quirked chunk_sectors setting to the same location as noiob so
one place registers this setting. And since the noiob value is only used
locally, remove the member from struct nvme_ns.
Introduce the new helper function nvme_lba_to_sect() to convert a device
logical block number to a 512B sector number. Use this new helper in
obvious places, cleaning up the code.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In register_mem_sect_under_node() the system_state's value is checked to
detect whether the call is made during boot time or during an hot-plug
operation. Unfortunately, that check against SYSTEM_BOOTING is wrong
because regular memory is registered at SYSTEM_SCHEDULING state. In
addition, memory hot-plug operation can be triggered at this system
state by the ACPI [1]. So checking against the system state is not
enough.
The consequence is that on system with interleaved node's ranges like this:
This can be seen on PowerPC LPAR after multiple memory hot-plug and
hot-unplug operations are done. At the next reboot the node's memory
ranges can be interleaved and since the call to link_mem_sections() is
made in topology_init() while the system is in the SYSTEM_SCHEDULING
state, the node's id is not checked, and the sections registered to
multiple nodes:
$ ls -l /sys/devices/system/memory/memory21/node*
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
In that case, the system is able to boot but if later one of theses
memory blocks is hot-unplugged and then hot-plugged, the sysfs
inconsistency is detected and this is triggering a BUG_ON():
This patch addresses the root cause by not relying on the system_state
value to detect whether the call is due to a hot-plug operation. An
extra parameter is added to link_mem_sections() detailing whether the
operation is due to a hot-plug operation.
[1] According to Oscar Salvador, using this qemu command line, ACPI
memory hotplug operations are raised at SYSTEM_SCHEDULING state:
In that case, we can see memory blocks assigned to multiple nodes in
sysfs:
$ ls -l /sys/devices/system/memory/memory21
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
-rw-r--r-- 1 root root 65536 Aug 24 05:27 online
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_device
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_index
drwxr-xr-x 2 root root 0 Aug 24 05:27 power
-r--r--r-- 1 root root 65536 Aug 24 05:27 removable
-rw-r--r-- 1 root root 65536 Aug 24 05:27 state
lrwxrwxrwx 1 root root 0 Aug 24 05:25 subsystem -> ../../../../bus/memory
-rw-r--r-- 1 root root 65536 Aug 24 05:25 uevent
-r--r--r-- 1 root root 65536 Aug 24 05:27 valid_zones
The same applies in the node's directory with a memory21 link in both
the node1 and node2's directory.
This is wrong but doesn't prevent the system to run. However when
later, one of these memory blocks is hot-unplugged and then hot-plugged,
the system is detecting an inconsistency in the sysfs layout and a
BUG_ON() is raised:
The root cause of this issue is that when node's memory is registered,
the range used can overlap another node's range, thus the memory block
is registered to multiple nodes in sysfs.
There are two issues here:
(a) The sysfs memory and node's layouts are broken due to these
multiple links
(b) The link errors in link_mem_sections() should not lead to a system
panic.
To address (a) register_mem_sect_under_node should not rely on the
system state to detect whether the link operation is triggered by a hot
plug operation or not. This is addressed by the patches 1 and 2 of this
series.
Issue (b) will be addressed separately.
This patch (of 2):
The memmap_context enum is used to detect whether a memory operation is
due to a hot-add operation or happening at boot time.
Make it general to the hotplug operation and rename it as
meminit_context.
There is no functional change introduced by this patch
Suggested-by: David Hildenbrand <david@redhat.com> Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J . Wysocki" <rafael@kernel.org> Cc: Nathan Lynch <nathanl@linux.ibm.com> Cc: Scott Cheloha <cheloha@linux.ibm.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20200915094143.79181-1-ldufour@linux.ibm.com Link: https://lkml.kernel.org/r/20200915132624.9723-1-ldufour@linux.ibm.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently io_ticks is approximated by adding one at each start and end of
requests if jiffies counter has changed. This works perfectly for requests
shorter than a jiffy or if one of requests starts/ends at each jiffy.
If disk executes just one request at a time and they are longer than two
jiffies then only first and last jiffies will be accounted.
Fix is simple: at the end of request add up into io_ticks jiffies passed
since last update rather than just one jiffy.
Example: common HDD executes random read 4k requests around 12ms.
Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") broke compilation and was temporarily fixed by Linus in 83bdc7275e62 ("random32: remove net_rand_state from the latent entropy
gcc plugin") by entirely moving net_rand_state out of the things handled
by the latent_entropy GCC plugin.
From what I understand when reading the plugin code, using the
__latent_entropy attribute on a declaration was the wrong part and
simply keeping the __latent_entropy attribute on the variable definition
was the correct fix.
the expectation is that host tools are built with debug informations.
This however doesn't happen if the Makefile assigns a new value to the
HOST_EXTRACFLAGS instead of appending to it. So use += instead of := for
the first assignment.
Fixes: e3fd9b5384f3 ("scripts/dtc: consolidate include path options in Makefile") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d8d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers") Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com> Acked-by: Jochen Friedrich <jochen@scram.de> Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c3e ("gpio: aspeed: Add in ast2600 details to Aspeed driver") Signed-off-by: Tao Ren <rentao.bupt@gmail.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver") Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver") Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
if of_find_device_by_node() succeed, exynos_iommu_of_xlate() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: aa759fd376fb ("iommu/exynos: Add callback for initializing devices from device tree") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20200918011335.909141-1-yukuai3@huawei.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b571777f ("clk: exynos4: register clocks using common clock framework") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit bff1cef5f23a ("clk: tegra: Don't enable already enabled PLLs")
added checks to avoid enabling PLLs that have already been enabled by
the bootloader. However, the PLL_E configuration inherited from the
bootloader isn't necessarily the one that is needed for the kernel.
This can cause SATA to fail like this:
[ 5.310270] phy phy-sata.6: phy poweron failed --> -110
[ 5.315604] tegra-ahci 70027000.sata: failed to power on AHCI controller: -110
[ 5.323022] tegra-ahci: probe of 70027000.sata failed with error -110
Fix this by always programming the PLL_E. This ensures that any mis-
configuration by the bootloader will be overwritten by the kernel.
nfs_readdir_page_filler() iterates over entries in a directory, reusing
the same security label buffer, but does not reset the buffer's length.
This causes decode_attr_security_label() to return -ERANGE if an entry's
security label is longer than the previous one's. This error, in
nfs4_decode_dirent(), only gets passed up as -EAGAIN, which causes another
failed attempt to copy into the buffer. The second error is ignored and
the remaining entries do not show up in ls, specifically the getdents64()
syscall.
Reproduce by creating multiple files in NFS and giving one of the later
files a longer security label. ls will not see that file nor any that are
added afterwards, though they will exist on the backend.
In nfs_readdir_page_filler(), reset security label buffer length before
every reuse
Per the datasheet the i2c functions use MPP_Sel=0x1. They are documented
as using MPP_Sel=0x4 as well but mixing 0x1 and 0x4 is clearly wrong. On
the board tested 0x4 resulted in a non-functioning i2c bus so stick with
0x1 which works.
Fixes: d7ae8f8dee7f ("pinctrl: mvebu: pinctrl driver for 98DX3236 SoC") Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20200907211712.9697-2-chris.packham@alliedtelesis.co.nz Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb47 ("gpio: Add GPIO driver for Spreadtrum SC9860 platform") Signed-off-by: Taiping Lai <taiping.lai@unisoc.com> Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com> Reviewed-by: Baolin Wang <baolin.wang7@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The lldd may have made calls to delete a remote port or local port and
the delete is in progress when the cli then attempts to create a new
controller. Currently, this proceeds without error although it can't be
very successful.
Fix this by validating that both the host port and remote port are
present when a new controller is to be created.
Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we use nvmeq->q_depth as the upper limit for a valid tag in
nvme_handle_cqe(), it is not correct. Because the available tag number
is recorded in tagset, which is not equal to nvmeq->q_depth.
The nvme driver registers interrupts for queues before initializing the
tagset, because it uses the number of successful request_irq() calls to
configure the tagset parameters. This allows a race condition with the
current tag validity check if the controller happens to produce an
interrupt with a corrupted CQE before the tagset is initialized.
Replace the driver's indirect tag check with the one already provided by
the block layer.
Signed-off-by: Xianting Tian <tian.xianting@h3c.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SPIE register contains counts for the TX FIFO so any time the irq
handler was invoked we would attempt to process the RX/TX fifos. Use the
SPIM value to mask the events so that we only process interrupts that
were expected.
This was a latent issue exposed by commit 3282a3da25bd ("powerpc/64:
Implement soft interrupt replay in C").
It would seem none of the kernel continuous integration does this:
$ cd tools/io_uring
$ make
Otherwise it may have noticed:
cc -Wall -Wextra -g -D_GNU_SOURCE -c -o io_uring-bench.o
io_uring-bench.c
io_uring-bench.c:133:12: error: static declaration of ‘gettid’
follows non-static declaration
133 | static int gettid(void)
| ^~~~~~
In file included from /usr/include/unistd.h:1170,
from io_uring-bench.c:27:
/usr/include/x86_64-linux-gnu/bits/unistd_ext.h:34:16: note:
previous declaration of ‘gettid’ was here
34 | extern __pid_t gettid (void) __THROW;
| ^~~~~~
make: *** [<builtin>: io_uring-bench.o] Error 1
The problem on Ubuntu 20.04 (with lk 5.9.0-rc5) is that unistd.h
already defines gettid(). So prefix the local definition with
"lk_".
For 64bit CONFIG_BASE_SMALL=0 systems PID_MAX_LIMIT is set by default to 4194304. During boot the kernel sets a new value based on number of CPUs
but no lower than 32768. It is 1024 per CPU so with 128 CPUs the default
becomes 131072 which needs six digits.
This value can be increased during run time but must not exceed the
initial upper limit.
Systemd sometime after v241 sets it to the upper limit during boot. The
result is that when the pid exceeds five digits, the trace output is a
little hard to read because it is no longer properly padded (same like
on big iron with 98+ CPUs).
Radiotap header field 'Channel flags' has '2 GHz spectrum' set to
'true' for 6GHz packet.
Change it to 5GHz as there isn't a separate option available for 6GHz.
This patch sets skb->protocol before transmitting frames on the HDLC
device, so that a user listening on the HDLC device with an AF_PACKET
socket will see outgoing frames' sll_protocol field correctly set and
consistent with that of incoming frames.
1. Control frames in hdlc_cisco and hdlc_ppp
When these drivers send control frames, skb->protocol is not set.
This value should be set to htons(ETH_P_HDLC), because when receiving
control frames, their skb->protocol is set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, which then calls
cisco_type_trans or ppp_type_trans. The skb->protocol of control frames
is set to htons(ETH_P_HDLC) so that the control frames can be received
by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the
control frames.
2. hdlc_fr
When this driver sends control frames, skb->protocol is set to internal
values used in this driver.
When this driver sends data frames (from upper stacked PVC devices),
skb->protocol is the same as that of the user data packet being sent on
the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3)
(for Ethernet-emulating PVC devices).
However, skb->protocol for both control frames and data frames should be
set to htons(ETH_P_HDLC), because when receiving, all frames received on
the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, and because this
driver doesn't provide a type_trans function in struct hdlc_proto,
all frames will have their skb->protocol set to htons(ETH_P_HDLC).
The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx
to process the frames (control frames are consumed and data frames
are re-received on upper PVC devices).
Cc: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver is a virtual driver stacked on top of Ethernet interfaces.
When this driver transmits data on the Ethernet device, the skb->protocol
setting is inconsistent with the Ethernet header prepended to the skb.
This causes a user listening on the Ethernet interface with an AF_PACKET
socket, to see different sll_protocol values for incoming and outgoing
frames, because incoming frames would have this value set by parsing the
Ethernet header.
This patch changes the skb->protocol value for outgoing Ethernet frames,
making it consistent with the Ethernet header prepended. This makes a
user listening on the Ethernet device with an AF_PACKET socket, to see
the same sll_protocol value for incoming and outgoing frames.
Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Get and put the reference to the ctrl in the nvme_dev_open() and
nvme_dev_release() before and after module get/put for ctrl in char
device file operations.
Introduce char_dev relase function, get/put the controller and module
which allows us to fix the potential Oops which can be easily reproduced
with a passthru ctrl (although the problem also exists with pure user
access):
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Increase Rx ring size to address issue where hardware is reaching
the receive work limit.
Before:
[ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached
Signed-off-by: Lucy Yan <lucyyan@google.com> Reviewed-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
PVC devices are virtual devices in this driver stacked on top of the
actual HDLC device. They are the devices normal users would use.
PVC devices have two types: normal PVC devices and Ethernet-emulating
PVC devices.
When transmitting data with PVC devices, the ndo_start_xmit function
will prepend a header of 4 or 10 bytes. Currently this driver requests
this headroom to be reserved for normal PVC devices by setting their
hard_header_len to 10. However, this does not work when these devices
are used with AF_PACKET/RAW sockets. Also, this driver does not request
this headroom for Ethernet-emulating PVC devices (but deals with this
problem by reallocating the skb when needed, which is not optimal).
This patch replaces hard_header_len with needed_headroom, and set
needed_headroom for Ethernet-emulating PVC devices, too. This makes
the driver to request headroom for all PVC devices in all cases.
Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ubuntu mainline builds for ppc64le are failing with the below error (*):
CALL /home/kernel/COD/linux/scripts/atomic/check-atomics.sh
DESCEND bpf/resolve_btfids
resolve_btfids needs to be build as a host binary and it needs libbpf.
However, libbpf Makefile hardcodes an include path utilizing $(ARCH).
This results in mixing of cross-architecture headers resulting in a
build failure.
The specific header include path doesn't seem necessary for a libbpf
build. Hence, remove the same.
When the timer counts to the upper limit, an overflow interrupt is
generated, and the count is reset with the value in the TIME_INI
register. But the software expects to start counting from 0 when
the count overflows, so it forces TIME_INI to 0 to solve the
potential interrupt storm problem.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com> Tested-by: Xu Kai <xukai@nationalchip.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/1597735877-71115-1-git-send-email-guoren@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
A recent attempt to fix a ref count leak in
amdgpu_display_crtc_set_config() turned out to be doing too much and
"fixed" an intended decrease as if it were a leak. Undo that part to
restore the proper balance. This is the very nature of this function
to increase or decrease the power reference count depending on the
situation.
Consequences of this bug is that the power reference would
eventually get down to 0 while the display was still in use,
resulting in that display switching off unexpectedly.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: e008fa6fb415 ("drm/amdgpu: fix ref count leak in amdgpu_display_crtc_set_config") Cc: stable@vger.kernel.org Cc: Navid Emamdoost <navid.emamdoost@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 6827ca573c03 ("memstick: rtsx_usb_ms: Support runtime power
management"), removing module rtsx_usb_ms will be stuck.
The deadlock is caused by powering on and powering off at the same time,
the former one is when memstick_check() is flushed, and the later is called
by memstick_remove_host().
Soe let's skip allocating card to prevent this issue.
The first thing that the ftrace function callback helper functions should do
is to check for recursion. Peter Zijlstra found that when
"rcu_is_watching()" had its notrace removed, it caused perf function tracing
to crash. This is because the call of rcu_is_watching() is tested before
function recursion is checked and and if it is traced, it will cause an
infinite recursion loop.
rcu_is_watching() should still stay notrace, but to prevent this should
never had crashed in the first place. The recursion prevention must be the
first thing done in callback functions.
Link: https://lore.kernel.org/r/20200929112541.GM2628@hirez.programming.kicks-ass.net Cc: stable@vger.kernel.org Cc: Paul McKenney <paulmck@kernel.org> Fixes: c68c0fa293417 ("ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too") Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Sandeen [Thu, 1 Oct 2020 13:34:48 +0000 (08:34 -0500)]
xfs: trim IO to found COW extent limit
A bug existed in the XFS reflink code between v5.1 and v5.5 in which
the mapping for a COW IO was not trimmed to the mapping of the COW
extent that was found. This resulted in a too-short copy, and
corruption of other files which shared the original extent.
(This happened only when extent size hints were set, which bypasses
delalloc and led to this code path.)
This was (inadvertently) fixed upstream with
36adcbace24e "xfs: fill out the srcmap in iomap_begin"
and related patches which moved lots of this functionality to
the iomap subsystem.
Hence, this is a -stable only patch, targeted to fix this
corruption vector without other major code changes.
Fixes: 78f0cc9d55cb ("xfs: don't use delalloc extents for COW on files with extsize hints") Cc: <stable@vger.kernel.org> # 5.4.x Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Whenever the vsock backend on the host sends a packet through the RX
queue, it expects an answer on the TX queue. Unfortunately, there is one
case where the host side will hang waiting for the answer and might
effectively never recover if no timeout mechanism was implemented.
This issue happens when the guest side starts binding to the socket,
which insert a new bound socket into the list of already bound sockets.
At this time, we expect the guest to also start listening, which will
trigger the sk_state to move from TCP_CLOSE to TCP_LISTEN. The problem
occurs if the host side queued a RX packet and triggered an interrupt
right between the end of the binding process and the beginning of the
listening process. In this specific case, the function processing the
packet virtio_transport_recv_pkt() will find a bound socket, which means
it will hit the switch statement checking for the sk_state, but the
state won't be changed into TCP_LISTEN yet, which leads the code to pick
the default statement. This default statement will only free the buffer,
while it should also respond to the host side, by sending a packet on
its TX queue.
In order to simply fix this unfortunate chain of events, it is important
that in case the default statement is entered, and because at this stage
we know the host side is waiting for an answer, we must send back a
packet containing the operation VIRTIO_VSOCK_OP_RST.
One could say that a proper timeout mechanism on the host side will be
enough to avoid the backend to hang. But the point of this patch is to
ensure the normal use case will be provided with proper responsiveness
when it comes to establishing the connection.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We are going to add 'struct vsock_sock *' parameter to
virtio_transport_get_ops().
In some cases, like in the virtio_transport_reset_no_sock(),
we don't have any socket assigned to the packet received,
so we can't use the virtio_transport_get_ops().
In order to allow virtio_transport_reset_no_sock() to use the
'.send_pkt' callback from the 'vhost_transport' or 'virtio_transport',
we add the 'struct virtio_transport *' to it and to its caller:
virtio_transport_recv_pkt().
We moved the 'vhost_transport' and 'virtio_transport' definition,
to pass their address to the virtio_transport_recv_pkt().
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
The gpio-siox driver uses handle_nested_irq() to implement its
interrupt support. This is only capable of handling threaded irq
actions. For a hardirq action it triggers a NULL pointer oops.
(It calls action->thread_fn which is NULL then.)
Prevent registration of a hardirq action by setting
gpio_irq_chip::threaded to true.
Cc: u.kleine-koenig@pengutronix.de Fixes: be8c8facc707 ("gpio: new driver to work with a 8x12 siox") Cc: stable@vger.kernel.org Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Commit bedf9fc01ff1 ("mmc: sdhci: Workaround broken command queuing on
Intel GLK"), disabled command-queuing on Intel GLK based LENOVO models
because of it being broken due to what is believed to be a bug in
the BIOS.
It seems that the BIOS of some IRBIS models, including the IRBIS NB111
model has the same issue, so disable command queuing there too.
Fixes: bedf9fc01ff1 ("mmc: sdhci: Workaround broken command queuing on Intel GLK") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209397 Reported-and-tested-by: RussianNeuroMancer <russianneuromancer@ya.ru> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200927104821.5676-1-hdegoede@redhat.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use a device's allocation state tree to track ranges in a device used
for allocated chunks, and we set ranges in this tree when allocating a new
chunk. However after a device replace operation, we were not setting the
allocated ranges in the new device's allocation state tree, so that tree
is empty after a device replace.
This means that a fitrim operation after a device replace will trim the
device ranges that have allocated chunks and extents, as we trim every
range for which there is not a range marked in the device's allocation
state tree. It is also important during chunk allocation, since the
device's allocation state is used to determine if a range is already
allocated when allocating a new chunk.
This is trivial to reproduce and the following script triggers the bug:
$ cat reproducer.sh
#!/bin/bash
DEV1="/dev/sdg"
DEV2="/dev/sdh"
DEV3="/dev/sdi"
wipefs -a $DEV1 $DEV2 $DEV3 &> /dev/null
# Create a raid1 test fs on 2 devices.
mkfs.btrfs -f -m raid1 -d raid1 $DEV1 $DEV2 > /dev/null
mount $DEV1 /mnt/btrfs
echo "Starting to replace $DEV1 with $DEV3"
btrfs replace start -B $DEV1 $DEV3 /mnt/btrfs
echo
echo "Running fstrim"
fstrim /mnt/btrfs
echo
echo "Unmounting filesystem"
umount /mnt/btrfs
echo "Mounting filesystem in degraded mode using $DEV3 only"
wipefs -a $DEV1 $DEV2 &> /dev/null
mount -o degraded $DEV3 /mnt/btrfs
if [ $? -ne 0 ]; then
dmesg | tail
echo
echo "Failed to mount in degraded mode"
exit 1
fi
echo
echo "File foo data (expected all bytes = 0xab):"
od -A d -t x1 /mnt/btrfs/foo
umount /mnt/btrfs
When running the reproducer:
$ ./replace-test.sh
wrote 10485760/10485760 bytes at offset 0
10 MiB, 2560 ops; 0.0901 sec (110.877 MiB/sec and 28384.5216 ops/sec)
Starting to replace /dev/sdg with /dev/sdi
Running fstrim
Unmounting filesystem
Mounting filesystem in degraded mode using /dev/sdi only
mount: /mnt/btrfs: wrong fs type, bad option, bad superblock on /dev/sdi, missing codepage or helper program, or other error.
[19581.748641] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi started
[19581.803842] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi finished
[19582.208293] BTRFS info (device sdi): allowing degraded mounts
[19582.208298] BTRFS info (device sdi): disk space caching is enabled
[19582.208301] BTRFS info (device sdi): has skinny extents
[19582.212853] BTRFS warning (device sdi): devid 2 uuid 1f731f47-e1bb-4f00-bfbb-9e5a0cb4ba9f is missing
[19582.213904] btree_readpage_end_io_hook: 25839 callbacks suppressed
[19582.213907] BTRFS error (device sdi): bad tree block start, want 30490624 have 0
[19582.214780] BTRFS warning (device sdi): failed to read root (objectid=7): -5
[19582.231576] BTRFS error (device sdi): open_ctree failed
Failed to mount in degraded mode
So fix by setting all allocated ranges in the replace target device when
the replace operation is finishing, when we are holding the chunk mutex
and we can not race with new chunk allocations.
A test case for fstests follows soon.
Fixes: 1c11b63eff2a67 ("btrfs: replace pending/pinned chunks lists with io tree") CC: stable@vger.kernel.org # 5.2+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several reports that the BUG_ON on unsupported command in
mv_qc_prep can be triggered under some circumstances:
https://bugzilla.suse.com/show_bug.cgi?id=1110252
https://serverfault.com/questions/888897/raid-problems-after-power-outage
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1652185
https://bugs.centos.org/view.php?id=14998
Let sata_mv handle the failure gracefully: warn about that incl. the
failed command number and return an AC_ERR_INVALID error. We can do that
now thanks to the previous patch.
projects / users / dwmw2 / linux.git / log