In the commit referenced below I failed to pay attention to this code
also being buildable as 32-bit. Adjust the type of "ret" - there's no
real need for it to be wider than 32 bits.
Fixes: 934ef33ee75c ("x86/PVH: obtain VGA console info in Dom0") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/2d2193ff-670b-0a27-e12d-2c5c4c121c79@suse.com Signed-off-by: Juergen Gross <jgross@suse.com>
Recently, when automatically merging -net and net-next in MPTCP devel
tree, our CI reported [1] a conflict in hsr, the same as the one
reported by Stephen in netdev [2].
When looking at the conflict, I noticed it is in fact the v1 [3] that
has been applied in -net and the v2 [4] in net-next. Maybe the v1 was
applied by accident.
As mentioned by Jakub Kicinski [5], the new condition makes more sense
before the net_ratelimit(), not to update net_ratelimit's state which is
unnecessary if we're not going to print either way.
Here, this modification applies the v2 but in -net.
During miration to vram prange->offset is valid after vram buffer is located,
either use old one or allocate a new one. Move svm_range_vram_node_new before
migrate for each vma to get valid prange->offset.
v2: squash in warning fix
Fixes: b4ee9606378b ("drm/amdkfd: Fix BO offset for multi-VMA page migration") Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ucsi_init() which runs from a workqueue sets ucsi->connector and
on an error will clear it again.
ucsi->connector gets dereferenced by ucsi_resume(), this checks for
ucsi->connector being NULL in case ucsi_init() has not finished yet;
or in case ucsi_init() has failed.
ucsi_init() setting ucsi->connector and then clearing it again on
an error creates a race where the check in ucsi_resume() may pass,
only to have ucsi->connector free-ed underneath it when ucsi_init()
hits an error.
Fix this race by making ucsi_init() store the connector array in
a local variable and only assign it to ucsi->connector on success.
Fixes: bdc62f2bae8f ("usb: typec: ucsi: Simplified registration and I/O API") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230308154244.722337-3-hdegoede@redhat.com Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bug in btf_dump's logic of determining if a given struct type is
packed or not. The notion of "natural alignment" is not needed and is
even harmful in this case, so drop it altogether. The biggest difference
in btf_is_struct_packed() compared to its original implementation is
that we don't really use btf__align_of() to determine overall alignment
of a struct type (because it could be 1 for both packed and non-packed
struct, depending on specifci field definitions), and just use field's
actual alignment to calculate whether any field is requiring packing or
struct's size overall necessitates packing.
Add two simple test cases that demonstrate the difference this change
would make.
Fixes: ea2ce1ba99aa ("libbpf: Fix BTF-to-C converter's padding logic") Reported-by: Eduard Zingerman <eddyz87@gmail.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Eduard Zingerman <eddyz87@gmail.com> Link: https://lore.kernel.org/bpf/20221215183605.4149488-1-andrii@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Turns out that btf_dump API doesn't handle a bunch of tricky corner
cases, as reported by Per, and further discovered using his testing
Python script ([0]).
This patch revamps btf_dump's padding logic significantly, making it
more correct and also avoiding unnecessary explicit padding, where
compiler would pad naturally. This overall topic turned out to be very
tricky and subtle, there are lots of subtle corner cases. The comments
in the code tries to give some clues, but comments themselves are
supposed to be paired with good understanding of C alignment and padding
rules. Plus some experimentation to figure out subtle things like
whether `long :0;` means that struct is now forced to be long-aligned
(no, it's not, turns out).
Anyways, Per's script, while not completely correct in some known
situations, doesn't show any obvious cases where this logic breaks, so
this is a nice improvement over the previous state of this logic.
Some selftests had to be adjusted to accommodate better use of natural
alignment rules, eliminating some unnecessary padding, or changing it to
`type: 0;` alignment markers.
Note also that for when we are in between bitfields, we emit explicit
bit size, while otherwise we use `: 0`, this feels much more natural in
practice.
Next patch will add few more test cases, found through randomized Per's
script.
Structures with zero regular fields but some padding constitute a
special case in btf_dump.c:btf_dump_emit_struct_def with regards to
newline before closing '}'.
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We walk the userspace PTs to discover what mapping size was
used there. However, this can race against the userspace tables
being freed, and we end-up in the weeds.
Thankfully, the mm code is being generous and will IPI us when
doing so. So let's implement our part of the bargain and disable
interrupts around the walk. This ensures that nothing terrible
happens during that time.
We still need to handle the removal of the page tables before
the walk. For that, allow get_user_mapping_size() to return an
error, and make sure this error can be propagated all the way
to the the exit handler.
Have KVM_GET_ONE_REG for vPMU counter (vPMC) registers (PMCCNTR_EL0
and PMEVCNTR<n>_EL0) return the sum of the register value in the sysreg
file and the current perf event counter value.
Values of vPMC registers are saved in sysreg files on certain occasions.
These saved values don't represent the current values of the vPMC
registers if the perf events for the vPMCs count events after the save.
The current values of those registers are the sum of the sysreg file
value and the current perf event counter value. But, when userspace
reads those registers (using KVM_GET_ONE_REG), KVM returns the sysreg
file value to userspace (not the sum value).
Fix this to return the sum value for KVM_GET_ONE_REG.
SKL/GLK CSC unit suffers from a nasty issue where a CSC
coeff/offset register read or write between DC5 exit and
PSR exit will undo the CSC arming performed by DMC, and
then during PSR exit the hardware will latch zeroes into
the active CSC registers. This causes any plane going
through the CSC to output all black.
We can sidestep the issue by making sure the PSR exit has
already actually happened before we touch the CSC coeff/offset
registers. Easiest way to guarantee that is to just move the
CSC programming back into the .color_commir_arm() as we force
a PSR exit (and crucially wait for it to actually happen)
prior to touching the arming registers.
When PSR (and thus also DC states) are disabled we don't
have anything to worry about, so we can keep using the
more optional _noarm() hook for writing the CSC registers.
Cc: <stable@vger.kernel.org> #v5.19+ Cc: Manasi Navare <navaremanasi@google.com> Cc: Drew Davenport <ddavenport@chromium.org> Cc: Imre Deak <imre.deak@intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8283 Fixes: d13dde449580 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-3-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 80a892a4c2428b65366721599fc5fe50eaed35fd) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keeping DC states enabled is incompatible with the _noarm()/_arm()
split we use for writing pipe/plane registers. When DC5 and PSR
are enabled, all pipe/plane registers effectively become self-arming
on account of DC5 exit arming the update, and PSR exit latching it.
What probably saves us most of the time is that (with PIPE_MISC[21]=0)
all pipe register writes themselves trigger PSR exit, and then
we don't re-enter PSR until the idle frame count has elapsed.
So it may be that the PSR exit happens already before we've
updated the state too much.
Also the PSR1 panel (at least on this KBL) seems to discard the first
frame we trasmit, presumably still scanning out from its internal
framebuffer at that point. So only the second frame we transmit is
actually visible. But I suppose that could also be panel specific
behaviour. I haven't checked out how other PSR panels behave, nor
did I bother to check what the eDP spec has to say about this.
And since this really is all about DC states, let's switch from
the MODESET domain to the DC_OFF domain. Functionally they are
100% identical. We should probably remove the MODESET domain...
And for good measure let's toss in an assert to the place where
we do the _noarm() register writes to make sure DC states are
in fact off.
v2: Just use intel_display_power_is_enabled() (Imre)
Currently i915_gem_object_is_framebuffer() doesn't treat the
BO containing the framebuffer's DPT as a framebuffer itself.
This means eg. that the shrinker can evict the DPT BO while
leaving the actual FB BO bound, when the DPT is allocated
from regular shmem.
That causes an immediate oops during hibernate as we
try to rewrite the PTEs inside the already evicted
DPT obj.
TODO: presumably this might also be the reason for the
DPT related display faults under heavy memory pressure,
but I'm still not sure how that would happen as the object
should be pinned by intel_dpt_pin() while in active use by
the display engine...
Cc: stable@vger.kernel.org Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Imre Deak <imre.deak@intel.com> Fixes: 0dc987b699ce ("drm/i915/display: Add smem fallback allocation for dpt") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230320090522.9909-2-ville.syrjala@linux.intel.com Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
(cherry picked from commit 779cb5ba64ec7df80675a956c9022929514f517a) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i915_gem_object_create_lmem_from_data() lacks the flush of the data
written to lmem to ensure the object is marked as dirty and the writes
flushed to the backing store. Once created, we can immediately release
the obj->mm.mapping caching of the vmap.
Fixes: 7acbbc7cf485 ("drm/i915/guc: put all guc objects in lmem when available") Cc: Matthew Auld <matthew.auld@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Andi Shyti <andi.shyti@linux.intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Cc: John Harrison <John.C.Harrison@Intel.com> Signed-off-by: Chris Wilson <chris.p.wilson@linux.intel.com> Cc: <stable@vger.kernel.org> # v5.16+ Signed-off-by: Nirmoy Das <nirmoy.das@intel.com> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> Reviewed-by: Nirmoy Das <nirmoy.das@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230316165918.13074-1-nirmoy.das@intel.com
(cherry picked from commit e2ee10474ce766686e7a7496585cdfaf79e3a1bf) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8b/10b encoding needs to add 3% fec overhead into the pbn.
In the Synapcis Cascaded MST hub, the first stage MST branch device
needs the information to determine the timeslot count for the
second stage MST branch device. Missing this overhead will leads to
insufficient timeslot allocation.
Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Traditional synaptics hub has one MST branch device without virtual dpcd.
Synaptics cascaded hub has two chained MST branch devices. DSC decoding
is performed via root MST branch device, instead of the second MST branch
device.
Skip mode2 reset only for IMU enabled APUs when do S4.
This patch is to fix the regression issue
https://gitlab.freedesktop.org/drm/amd/-/issues/2483
It is generated by commit b589626674de ("drm/amdgpu: skip ASIC reset
for APUs when go to S4").
Fixes: b589626674de ("drm/amdgpu: skip ASIC reset for APUs when go to S4") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2483 Tested-by: Yuan Perry <Perry.Yuan@amd.com> Signed-off-by: Tim Huang <tim.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 6.1.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_gem_prime_mmap() takes a reference on the GEM object, but before that
drm_gem_mmap_obj() already takes a reference, which will be leaked as only
one reference is dropped when the mapping is closed. Drop the extra
reference when dma_buf_mmap() succeeds.
Cc: stable@vger.kernel.org Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing earlyclobber annotation to size, to, and tmp2 operands of the
__clear_user() inline assembly since they are modified or written to before
the last usage of all input operands. This can lead to incorrect register
allocation for the inline assembly.
Fixes: 6c2a9e6df604 ("[S390] Use alternative user-copy operations for new hardware.") Reported-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/all/20230321122514.1743889-3-mark.rutland@arm.com/ Cc: stable@vger.kernel.org Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI EEPROMs typically support both SPI Mode 0 (CPOL=CPHA=0) and Mode 3
(CPOL=CPHA=1). However, using the latter is currently flagged as an
error by "make dtbs_check", e.g.:
arch/arm/boot/dts/r8a7791-koelsch.dtb: flash@0: Unevaluated properties are not allowed ('spi-cpha', 'spi-cpol' were unexpected)
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Fix this by documenting support for CPOL=CPHA=1.
Fixes: 233363aba72ac638 ("spi/panel: dt-bindings: drop CPHA and CPOL from common properties") Cc: stable@vger.kernel.org Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/afe470603028db9374930b0c57464b1f6d52bdd3.1676384304.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the rcutorturename field so that its size is correctly reported in
the text format embedded in trace.dat files. As it stands, it is
reported as being of size 1:
show_stack dumps raw stack contents which may trigger an unnecessary
KASAN report. Fix it by copying stack contents to a temporary buffer
with __memcpy and then printing that buffer instead of passing stack
pointer directly to the print_hex_dump.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been reported that the recent kernel can't probe the PCM devices
on Roland VS-100 properly, and it turned out to be a regression by the
recent addition of the bit shift range check for the format bits.
In the old code, we just did bit-shift and it resulted in zero, which
is then corrected to the standard PCM format, while the new code
explicitly returns an error in such a case.
For addressing the regression, relax the check and fallback to the
standard PCM type (with the info output).
The recent commit f83bb2592482 ("ALSA: hda/conexant: Add quirk for
LENOVO 20149 Notebook model") introduced a quirk for the device with
17aa:3977, but this caused a regression on another model (Lenovo
Ideadpad U31) with the very same PCI SSID. And, through skimming over
the net, it seems that this PCI SSID is used for multiple different
models, so it's no good idea to apply the quirk with the SSID.
Although we may take a different ID check (e.g. the codec SSID instead
of the PCI SSID), unfortunately, the original patch author couldn't
identify the hardware details any longer as the machine was returned,
and we can't develop the further proper fix.
In this patch, instead, we partially revert the change so that the
quirk won't be applied as default for addressing the regression.
Meanwhile, the quirk function itself is kept, and it's now made to be
applicable via the explicit model=lenovo-20149 option.
When we're using a cached open stateid or a delegation in order to avoid
sending a CLAIM_PREVIOUS open RPC call to the server, we don't have a
new open stateid to present to update_open_stateid().
Instead rely on nfs4_try_open_cached(), just as if we were doing a
normal open.
Userspace PROT_NONE ptes set _PAGE_PRIVILEGED, triggering a false
positive debug assertion that __pte_flags_need_flush() is not called
on a kernel mapping.
Detect when it is a userspace PROT_NONE page by checking the required
bits of PAGE_NONE are set, and none of the RWX bits are set.
pte_protnone() is insufficient here because it always returns 0 when
CONFIG_NUMA_BALANCING=n.
Fixes: b11931e9adc1 ("powerpc/64s: add pte_needs_flush and huge_pmd_needs_flush") Cc: stable@vger.kernel.org # v6.1+ Reported-by: Russell Currey <ruscur@russell.cc> Signed-off-by: Benjamin Gray <bgray@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230302225947.81083-1-bgray@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hypervisor supports user-mode NX from Power10.
pseries_vas_dlpar_cpu() is called from lparcfg_write() to update VAS
windows for DLPAR event in shared processor mode and the kernel gets
-ENOTSUPP for HCALLs if the user-mode NX is not supported. The current
VAS implementation also supports only with Radix page tables. Whereas in
dedicated processor mode, pseries_vas_notifier() is registered only if
the copy/paste feature is enabled. So instead of displaying HCALL error
messages, update VAS capabilities if the copy/paste feature is
available.
This patch ignores updating VAS capabilities in pseries_vas_dlpar_cpu()
and returns success if the copy/paste feature is not enabled. Then
lparcfg_write() completes the processor DLPAR operations without any
failures.
Fixes: 2147783d6bf0 ("powerpc/pseries: Use lparcfg to reconfig VAS windows for DLPAR CPU") Cc: stable@vger.kernel.org # v6.1+ Signed-off-by: Haren Myneni <haren@linux.ibm.com> Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/1d0e727e7dbd9a28627ef08ca9df9c86a50175e2.camel@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
powerpc sets up PF_KTHREAD and PF_IO_WORKER with a NULL pt_regs, which
from my (arguably very short) checking is not commonly done for other
archs. This is fine, except when PF_IO_WORKER's have been created and
the task does something that causes a coredump to be generated. Then we
get this crash:
Because ppr_get() is trying to copy from a PF_IO_WORKER with a NULL
pt_regs.
Check for a valid pt_regs in both ppc_get/ppr_set, and return an error
if not set. The actual error value doesn't seem to be important here, so
just pick -EINVAL.
Fixes: fa439810cc1b ("powerpc/ptrace: Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR") Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Jens Axboe <axboe@kernel.dk>
[mpe: Trim oops in change log, add Fixes & Cc stable] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/d9f63344-fe7c-56ae-b420-4a1a04a2ae4c@kernel.dk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5829f8a897e4 ("platform/x86: ideapad-laptop: Send
KEY_TOUCHPAD_TOGGLE on some models") made ideapad-laptop send
KEY_TOUCHPAD_TOGGLE when we receive an ACPI notify with VPC event bit 5 set
and the touchpad-state has not been changed by the EC itself already.
This was done under the assumption that this would be good to do to make
the touchpad-toggle hotkey work on newer models where the EC does not
toggle the touchpad on/off itself (because it is not routed through
the PS/2 controller, but uses I2C).
But it turns out that at least some models, e.g. the Yoga 7-15ITL5 the EC
triggers an ACPI notify with VPC event bit 5 set on resume, which would
now cause a spurious KEY_TOUCHPAD_TOGGLE on resume to which the desktop
environment responds by disabling the touchpad in software, breaking
the touchpad (until manually re-enabled) on resume.
It was never confirmed that sending KEY_TOUCHPAD_TOGGLE actually improves
things on new models and at least some new models like the Yoga 7-15ITL5
don't have a touchpad on/off toggle hotkey at all, while still sending
ACPI notify events with VPC event bit 5 set.
So it seems best to revert the change to send KEY_TOUCHPAD_TOGGLE when
receiving an ACPI notify events with VPC event bit 5 and the touchpad
state as reported by the EC has not changed.
Note this is not a full revert the code to cache the last EC touchpad
state is kept to avoid sending spurious KEY_TOUCHPAD_ON / _OFF events
on resume.
Since commit d59f6617eef0 ("genirq: Allow fwnode to carry name
information only") an IRQ domain is always given a name during
allocation (e.g. used for the debugfs entry).
Drop the no longer valid name assignment, which would lead to an attempt
to free a string constant when removing the domain on late probe
failures (e.g. probe deferral).
Fixes: d59f6617eef0 ("genirq: Allow fwnode to carry name information only") Cc: stable@vger.kernel.org # 4.13 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> # on SAMA7G5 Link: https://lore.kernel.org/r/20230224130828.27985-1-johan+linaro@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a similar problem to the one observed in:
commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe").
On some systems, during suspend/resume cycle firmware leaves
an interrupt enabled on a pin that is not used by the kernel.
This confuses the AMD pinctrl driver and causes spurious interrupts.
The driver already has logic to detect if a pin is used by the kernel.
Leverage it to re-initialize interrupt fields of a pin only if it's not
used by us.
modpost now reads CRCs from .*.cmd files, parsing them using strtol().
This is inconsistent with its parsing of Module.symvers and with their
definition as *unsigned* 32-bit values.
strtol() clamps values to [LONG_MIN, LONG_MAX], and when building on a
32-bit system this changes all CRCs >= 0x80000000 to be 0x7fffffff.
Change extract_crcs_for_object() to use strtoul() instead.
Cc: stable@vger.kernel.org Fixes: f292d875d0dc ("modpost: extract symbol versions from *.cmd files") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dp83869 internally uses a look-up table for mapping supported delays in
nanoseconds to register values.
When specific delays are defined in device-tree, phy_get_internal_delay
does the lookup automatically returning an index.
The default case wrongly assigns the nanoseconds value from the lookup
table, resulting in numeric value 2000 applied to delay configuration
register, rather than the expected index values 0-7 (7 for 2000).
Ultimately this issue broke RX for 1Gbps links.
Fix default delay configuration by assigning the intended index value
directly.
Fix xenvif_get_requests() not to do grant copy operations across local
page boundaries. This requires to double the maximum number of copy
operations per queue, as each copy could now be split into 2.
Make sure that struct xenvif_tx_cb doesn't grow too large.
Cc: stable@vger.kernel.org Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses a deadlock situation that can occur in certain
scenarios, such as when running data TP/ETP transfer and subscribing to
the error queue while receiving a net down event. The deadlock involves
locks in the following order:
The solution implemented in this commit is to move the
j1939_sk_errqueue() call out of the active_session_list_lock context,
thus preventing the deadlock situation.
Commit 7dd76d1feec70 ("dm: improve bio splitting and associated IO
accounting") only called setup_split_accounting() from
__send_duplicate_bios() if a single bio were being issued. But the case
where duplicate bios are issued must call it too.
Otherwise the bio won't be split and resubmitted (via recursion through
block core back to DM) to submit the later portions of a bio (which may
map to an entirely different target).
For example, when discarding an entire DM striped device with the
following DM table:
vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048
When a direct append write is executed, the append offset may correspond
to the last page of a sequential file inode which might have been cached
already by buffered reads, page faults with mmap-read or non-direct
readahead. To ensure that the on-disk and cached data is consistant for
such last cached page, make sure to always invalidate it in
zonefs_file_dio_append(). If the invalidation fails, return -EBUSY to
userspace to differentiate from IO errors.
This invalidation will always be a no-op when the FS block size (device
zone write granularity) is equal to the page size (e.g. 4K).
Reported-by: Hans Holmberg <Hans.Holmberg@wdc.com> Fixes: 02ef12a663c7 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Tested-by: Hans Holmberg <hans.holmberg@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, vmxnet3 uses GRO callback only if LRO is disabled. However,
on smartNic based setups where UPT is supported, LRO can be enabled
from guest VM but UPT devicve does not support LRO as of now. In such
cases, there can be performance degradation as GRO is not being done.
This patch fixes this issue by calling GRO API when UPT is enabled. We
use updateRxProd to determine if UPT mode is active or not.
To clarify few things discussed over the thread:
The patch is not neglecting any feature bits nor disabling GRO. It uses
GRO callback when UPT is active as LRO is not available in UPT.
GRO callback cannot be used as default for all cases as it degrades
performance for non-UPT cases or for cases when LRO is already done in
ESXi.
Cc: stable@vger.kernel.org Fixes: 6f91f4ba046e ("vmxnet3: add support for capability registers") Signed-off-by: Ronak Doshi <doshir@vmware.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230323200721.27622-1-doshir@vmware.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We increase cache->nr_cached when we free into the cache but don't
decrease when we take from it, so in some time we'll get an empty
cache with cache->nr_cached larger than IO_ALLOC_CACHE_MAX, that fails
io_alloc_cache_put() and effectively disables caching.
We should not be looking at ctx->rsrc_node and anyhow modifying the node
without holding uring_lock, grabbing references in such a way is not
safe either.
Unless we have at least one entry queued, then don't call into
io_poll_remove_entries(). Normally this isn't possible, but if we
retry poll then we can have ->nr_entries cleared again as we're
setting it up. If this happens for a poll retry, then we'll still have
at least REQ_F_SINGLE_POLL set. io_poll_remove_entries() then thinks
it has entries to remove.
Clear REQ_F_SINGLE_POLL and REQ_F_DOUBLE_POLL unconditionally when
arming a poll request.
io_uring_cmd_done() currently assumes that the uring_lock is held
when invoked, and while it generally is, this is not guaranteed.
Pass in the issue_flags associated with it, so that we have
IO_URING_F_UNLOCKED available to be able to lock the CQ ring
appropriately when completing events.
The call to invalidate_inode_pages2_range() in __iomap_dio_rw() may
fail, in which case -ENOTBLK is returned and this error code is
propagated back to user space trhough iomap_dio_rw() ->
zonefs_file_dio_write() return chain. This error code is fairly obscure
and may confuse the user. Avoid this and be consistent with the behavior
of zonefs_file_dio_append() for similar invalidate_inode_pages2_range()
errors by returning -EBUSY to user space when iomap_dio_rw() returns
-ENOTBLK.
Suggested-by: Christoph Hellwig <hch@infradead.org> Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Tested-by: Hans Holmberg <hans.holmberg@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes mkfs/mount/check failures due to race with systemd-udevd
scan.
During the device scan initiated by systemd-udevd, other user space
EXCL operations such as mkfs, mount, or check may get blocked and result
in a "Device or resource busy" error. This is because the device
scan process opens the device with the EXCL flag in the kernel.
Two reports were received:
- btrfs/179 test case, where the fsck command failed with the -EBUSY
error
- LTP pwritev03 test case, where mkfs.vfs failed with
the -EBUSY error, when mkfs.vfs tried to overwrite old btrfs filesystem
on the device.
In both cases, fsck and mkfs (respectively) were racing with a
systemd-udevd device scan, and systemd-udevd won, resulting in the
-EBUSY error for fsck and mkfs.
Reproducing the problem has been difficult because there is a very
small window during which these userspace threads can race to
acquire the exclusive device open. Even on the system where the problem
was observed, the problem occurrences were anywhere between 10 to 400
iterations and chances of reproducing decreases with debug printk()s.
However, an exclusive device open is unnecessary for the scan process,
as there are no write operations on the device during scan. Furthermore,
during the mount process, the superblock is re-read in the below
function call chain:
So, to fix this issue, removes the FMODE_EXCL flag from the scan
operation, and add a comment.
The case where mkfs may still write to the device and a scan is running,
the btrfs signature is not written at that time so scan will not
recognize such device.
Reported-by: Sherry Yang <sherry.yang@oracle.com> Reported-by: kernel test robot <oliver.sang@intel.com> Link: https://lore.kernel.org/oe-lkp/202303170839.fdf23068-oliver.sang@intel.com CC: stable@vger.kernel.org # 5.4+ Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quota assign ioctl can currently run in parallel with a quota disable
ioctl call. The assign ioctl uses the quota root, while the disable ioctl
frees that root, and therefore we can have a use-after-free triggered in
the assign ioctl, leading to a trace like the following when KASAN is
enabled:
Fix this by having the qgroup assign ioctl take the qgroup ioctl mutex
before calling btrfs_run_qgroups(), which is what all qgroup ioctls should
call.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com> Link: https://lore.kernel.org/linux-btrfs/CAFcO6XN3VD8ogmHwqRk4kbiwtpUSNySu2VAxN8waEPciCHJvMA@mail.gmail.com/ CC: stable@vger.kernel.org # 5.10+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before relocating a block group we pause scrub, then do the relocation and
then unpause scrub. The relocation process requires starting and committing
a transaction, and if we have a failure in the critical section of the
transaction commit path (transaction state >= TRANS_STATE_COMMIT_START),
we will deadlock if there is a paused scrub.
1) A scrub is running, so fs_info->scrubs_running is 1;
2) Task A starts block group relocation, and at btrfs_relocate_chunk() it
pauses scrub by calling btrfs_scrub_pause(). That increments
fs_info->scrub_pause_req from 0 to 1 and waits for the scrub task to
pause (for fs_info->scrubs_paused to be == to fs_info->scrubs_running);
3) The scrub task pauses at scrub_pause_off(), waiting for
fs_info->scrub_pause_req to decrease to 0;
4) Task A then enters btrfs_relocate_block_group(), and down that call
chain we start a transaction and then attempt to commit it;
5) When task A calls btrfs_commit_transaction(), it either will do the
commit itself or wait for some other task that already started the
commit of the transaction - it doesn't matter which case;
6) The transaction commit enters state TRANS_STATE_COMMIT_START;
7) An error happens during the transaction commit, like -ENOSPC when
running delayed refs or delayed items for example;
8) This results in calling transaction.c:cleanup_transaction(), where
we call btrfs_scrub_cancel(), incrementing fs_info->scrub_cancel_req
from 0 to 1, and blocking this task waiting for fs_info->scrubs_running
to decrease to 0;
9) From this point on, both the transaction commit and the scrub task
hang forever:
1) The transaction commit is waiting for fs_info->scrubs_running to
be decreased to 0;
2) The scrub task is at scrub_pause_off() waiting for
fs_info->scrub_pause_req to decrease to 0 - so it can not proceed
to stop the scrub and decrement fs_info->scrubs_running from 0 to 1.
Therefore resulting in a deadlock.
Fix this by having cleanup_transaction(), called if a transaction commit
fails, not call btrfs_scrub_cancel() if relocation is in progress, and
having btrfs_relocate_block_group() call btrfs_scrub_cancel() instead if
the relocation failed and a transaction abort happened.
This was triggered with btrfs/061 from fstests.
Fixes: 55e3a601c81c ("btrfs: Fix data checksum error cause by replace with io-load.") CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Bastien Nocera <hadess@hadess.net> Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiled with CONFIG_CIFS_DFS_UPCALL disabled, cifs_dfs_d_automount
is NULL. cifs.ko logic for mapping CIFS_FATTR_DFS_REFERRAL attributes to
S_AUTOMOUNT and corresponding dentry flags is retained regardless of
CONFIG_CIFS_DFS_UPCALL, leading to a NULL pointer dereference in
VFS follow_automount() when traversing a DFS referral link:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
<TASK>
__traverse_mounts+0xb5/0x220
? cifs_revalidate_mapping+0x65/0xc0 [cifs]
step_into+0x195/0x610
? lookup_fast+0xe2/0xf0
path_lookupat+0x64/0x140
filename_lookup+0xc2/0x140
? __create_object+0x299/0x380
? kmem_cache_alloc+0x119/0x220
? user_path_at_empty+0x31/0x50
user_path_at_empty+0x31/0x50
__x64_sys_chdir+0x2a/0xd0
? exit_to_user_mode_prepare+0xca/0x100
do_syscall_64+0x42/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
This fix adds an inline cifs_dfs_d_automount() {return -EREMOTE} handler
when CONFIG_CIFS_DFS_UPCALL is disabled. An alternative would be to
avoid flagging S_AUTOMOUNT, etc. without CONFIG_CIFS_DFS_UPCALL. This
approach was chosen as it provides more control over the error path.
Signed-off-by: David Disseldorp <ddiss@suse.de> Cc: stable@vger.kernel.org Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't call smb_init() in CIFSGetDFSRefer() as cifs_reconnect_tcon()
may end up calling CIFSGetDFSRefer() again to get new DFS referrals
and thus causing an infinite recursion.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Cc: stable@vger.kernel.org # 6.2 Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent change of -funsigned-char causes additions of negative
numbers to become additions of large positive numbers, leading to wrong
calculations of mouse movement. Change these casts to be explicitly
signed, to take into account negative offsets.
The AlpsPS/2 code previously relied on the assumption that `char` is a
signed type, which was true on x86 platforms (the only place where this
driver is used) before kernel 6.2. However, on 6.2 and later, this
assumption is broken due to the introduction of -funsigned-char as a new
global compiler flag.
Fix this by explicitly specifying the signedness of `char` when sign
extending the values received from the device.
A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
Setting SERIO_QUIRK_NOMUX or SERIO_QUIRK_RESET_ALWAYS on the Clevo N150CU
and the Clevo NHxxRZQ makes the keyboard very laggy for ~5 seconds after
boot and sometimes also after resume. However both are required for the
keyboard to not fail completely sometimes after boot or resume.
The VT-d spec states (in section 11.4.2) that hardware implementations
reporting second-stage translation support (SSTS) field as Clear also
report the SAGAW field as 0. Fix an inappropriate check in alloc_iommu().
When commit commit fff1011a26d6 ("Input: xpad - add X-Box Adaptive Profile
button") was applied, one hunk ended up in the wrong function; move it to
where it belongs.
In case the driver was trying to set an alternate mode for gpio
0 or 32 then the mode was not set correctly. The reason is that
there is computation error inside the function ocelot_pinmux_set_mux
because in this case it was trying to shift to left by -1.
Fix this by actually shifting the function bits and not the position.
The cache needs to be flushed to ensure that the hardware stops offloading
the flow immediately.
Fixes: 33fc42de3327 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries") Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230330120840.52079-3-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since we call flow_block_cb_decref on FLOW_BLOCK_UNBIND, we also need to
call flow_block_cb_incref for a newly allocated cb.
Also fix the accidentally inverted refcount check on unbind.
Fixes: 502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support") Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230330120840.52079-1-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.") Signed-off-by: Steffen Bätz <steffen@innosonix.de> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b84 ("bnxt_en: ethtool: support PAM4 link speeds up to 200G") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In gsi_trans_pool_init_dma(), the total size of a pool of memory
used for DMA transactions is calculated. However the calculation is
done incorrectly.
For 4KB pages, this total size is currently always more than one
page, and as a result, the calculation produces a positive (though
incorrect) total size. The code still works in this case; we just
end up with fewer DMA pool entries than we intended.
Bjorn Andersson tested booting a kernel with 16KB pages, and hit a
null pointer derereference in sg_alloc_append_table_from_pages(),
descending from gsi_trans_pool_init_dma(). The cause of this was
that a 16KB total size was going to be allocated, and with 16KB
pages the order of that allocation is 0. The total_size calculation
yielded 0, which eventually led to the crash.
Correcting the total_size calculation fixes the problem.
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com> Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com> Fixes: 9dd441e4ed57 ("soc: qcom: ipa: GSI transactions") Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230328162751.2861791-1-elder@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
snd_card_ymfpci_remove() was removed in commit c6e6bb5eab74 ("ALSA:
ymfpci: Allocate resources with device-managed APIs"), but the call to
snd_card_new() was not replaced with snd_devm_card_new().
Since there was no longer a call to snd_card_free, unloading the module
would eventually result in Oops:
The code implicitly assumes that the list iterator finds a correct
handle. If 'vsi_handle' is not found the 'old_agg_vsi_info' was
pointing to an bogus memory location. For safety a separate list
iterator variable should be used to make the != NULL check on
'old_agg_vsi_info' correct under any circumstances.
Additionally Linus proposed to avoid any use of the list iterator
variable after the loop, in the attempt to move the list iterator
variable declaration into the macro to avoid any potential misuse after
the loop. Using it in a pointer comparison after the loop is undefined
behavior and should be omitted if possible [1].
Fixes: 37c592062b16 ("ice: remove the VSI info from previous agg") Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ Signed-off-by: Jakob Koschel <jkl820.git@gmail.com> Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add profile conflict check while adding some FDIR rules to avoid
unexpected flow behavior, rules may have conflict including:
IPv4 <---> {IPv4_UDP, IPv4_TCP, IPv4_SCTP}
IPv6 <---> {IPv6_UDP, IPv6_TCP, IPv6_SCTP}
For example, when we create an FDIR rule for IPv4, this rule will work
on packets including IPv4, IPv4_UDP, IPv4_TCP and IPv4_SCTP. But if we
then create an FDIR rule for IPv4_UDP and then destroy it, the first
FDIR rule for IPv4 cannot work on pkt IPv4_UDP then.
To prevent this unexpected behavior, we add restriction in software
when creating FDIR rules by adding necessary profile conflict check.
The current implementation causes ice_vsi_update() to update all VSI
fields based on the cached VSI context. This also assumes that the
ICE_AQ_VSI_PROP_Q_OPT_VALID bit is set. This can cause problems if the
VSI context is not correctly synced by the driver. Fix this by only
updating the fields that correspond to ICE_AQ_VSI_PROP_Q_OPT_VALID.
Also, make sure to save the updated result in the cached VSI context
on success.
Fixes: 348048e724a0 ("ice: Implement iidc operations") Co-developed-by: Robert Malz <robertx.malz@intel.com> Signed-off-by: Robert Malz <robertx.malz@intel.com> Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SMSC911x doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 3ce9f2bef755 ("net: smsc911x: Stop and start PHY during suspend and resume") Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230327083138.6044-1-wsa+renesas@sang-engineering.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In PPPoE add all IPv4 header option length to the parser
and adjust the L3 and L4 offset accordingly.
Currently the L4 match does not work with PPPoE and
all packets are matched as L3 IP4 OPT.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mvpp2 parser entry for QinQ has the inner and outer VLAN
in the wrong order.
Fix the problem by swapping them.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Reviewed-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
LOOP_CONFIGURE is, as far as I understand it, supposed to be a way to
combine LOOP_SET_FD and LOOP_SET_STATUS64 into a single syscall. When
using LOOP_SET_FD+LOOP_SET_STATUS64, a single uevent would be sent for
each partition found on the loop device after the second ioctl(), but
when using LOOP_CONFIGURE, no such uevent was being sent.
In the old setup, uevents are disabled for LOOP_SET_FD, but not for
LOOP_SET_STATUS64. This makes sense, as it prevents uevents being
sent for a partially configured device during LOOP_SET_FD - they're
only sent at the end of LOOP_SET_STATUS64. But for LOOP_CONFIGURE,
uevents were disabled for the entire operation, so that final
notification was never issued. To fix this, reduce the critical
section to exclude the loop_reread_partitions() call, which causes
the uevents to be issued, to after uevents are re-enabled, matching
the behaviour of the LOOP_SET_FD+LOOP_SET_STATUS64 combination.
I noticed this because Busybox's losetup program recently changed from
using LOOP_SET_FD+LOOP_SET_STATUS64 to LOOP_CONFIGURE, and this broke
my setup, for which I want a notification from the kernel any time a
new partition becomes available.
Signed-off-by: Alyssa Ross <hi@alyssa.is>
[hch: reduced the critical section] Signed-off-by: Christoph Hellwig <hch@lst.de> Fixes: 3448914e8cc5 ("loop: Add LOOP_CONFIGURE ioctl") Link: https://lore.kernel.org/r/20230320125430.55367-1-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
For ACPI drivers that provide a ->notify() callback and set
ACPI_DRIVER_ALL_NOTIFY_EVENTS in their flags, that callback can be
invoked while either the ->add() or the ->remove() callback is running
without any synchronization at the bus type level which is counter to
the common-sense expectation that notification handling should only be
enabled when the driver is actually bound to the device. As a result,
if the driver is not careful enough, it's ->notify() callback may crash
when it is invoked too early or too late [1].
This issue has been amplified by commit d6fb6ee1820c ("ACPI: bus: Drop
driver member of struct acpi_device") that made acpi_bus_notify() check
for the presence of the driver and its ->notify() callback directly
instead of using an extra driver pointer that was only set and cleared
by the bus type code, but it was present before that commit although
it was harder to reproduce then.
It can be addressed by using the observation that
acpi_device_install_notify_handler() can be modified to install the
handler for all types of events when ACPI_DRIVER_ALL_NOTIFY_EVENTS is
set in the driver flags, in which case acpi_bus_notify() will not need
to invoke the driver's ->notify() callback any more and that callback
will only be invoked after acpi_device_install_notify_handler() has run
and before acpi_device_remove_notify_handler() runs, which implies the
correct ordering with respect to the other ACPI driver callbacks.
Modify the code accordingly and while at it, drop two redundant local
variables from acpi_bus_notify() and turn its description comment into
a proper kerneldoc one.
Fixes: d6fb6ee1820c ("ACPI: bus: Drop driver member of struct acpi_device") Link: https://lore.kernel.org/linux-acpi/9f6cba7a8a57e5a687c934e8e406e28c.squirrel@mail.panix.com Reported-by: Pierre Asselin <pa@panix.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Pierre Asselin <pa@panix.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device release callback function invoked to release the matrix device
uses the dev_get_drvdata(device *dev) function to retrieve the
pointer to the vfio_matrix_dev object in order to free its storage. The
problem is, this object is not stored as drvdata with the device; since the
kfree function will accept a NULL pointer, the memory for the
vfio_matrix_dev object is never freed.
Since the device being released is contained within the vfio_matrix_dev
object, the container_of macro will be used to retrieve its pointer.
Fixes: 1fde573413b5 ("s390: vfio-ap: base implementation of VFIO AP device driver") Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Link: https://lore.kernel.org/r/20230320150447.34557-1-akrowiak@linux.ibm.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CPU: 1 PID: 5034 Comm: syz-executor350 Not tainted 6.2.0-rc6-syzkaller-80422-geda666ff2276 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
=====================================================
We can follow the call chain and find that 'bcm_tx_setup' function
calls 'memcpy_from_msg' to copy some content to the newly allocated
frame of 'op->frames'. After that the 'len' field of copied structure
being compared with some constant value (64 or 8). However, if
'memcpy_from_msg' returns an error, we will compare some uninitialized
memory. This triggers 'uninit-value' issue.
This patch will add 'memcpy_from_msg' possible errors processing to
avoid uninit-value issue.
For platforms with Alder Lake PCH (Alder Lake S and Raptor Lake S) the
slp_s0_residency attribute has been reporting the wrong value. Unlike other
platforms, ADL PCH does not have a counter for the time that the SLP_S0
signal was asserted. Instead, firmware uses the aggregate of the Low Power
Mode (LPM) substate counters as the S0ix value. Since the LPM counters run
at a different frequency, this lead to misreporting of the S0ix time.
Add a check for Alder Lake PCH and adjust the frequency accordingly when
display slp_s0_residency.
Fixes: bbab31101f44 ("platform/x86/intel: pmc/core: Add Alderlake support to pmc core driver") Signed-off-by: Rajvi Jingar <rajvi.jingar@linux.intel.com> Signed-off-by: David E. Box <david.e.box@linux.intel.com> Reviewed-by: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20230320212029.3154407-1-david.e.box@linux.intel.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The blamed commit has introduced the following tests to
dwmac4_add_hw_vlan_rx_fltr(), called from stmmac_vlan_rx_add_vid():
if (hw->promisc) {
netdev_err(dev,
"Adding VLAN in promisc mode not supported\n");
return -EPERM;
}
"VLAN promiscuous" mode is keyed in this driver to IFF_PROMISC, and so,
vlan_vid_add() and vlan_vid_del() calls cannot take place in IFF_PROMISC
mode. I have the following 2 arguments that this restriction is.... hm,
how shall I put it nicely... unproductive :)
First, take the case of a Linux bridge. If the kernel is compiled with
CONFIG_BRIDGE_VLAN_FILTERING=y, then this bridge shall have a VLAN
database. The bridge shall try to call vlan_add_vid() on its bridge
ports for each VLAN in the VLAN table. It will do this irrespectively of
whether that port is *currently* VLAN-aware or not. So it will do this
even when the bridge was created with vlan_filtering 0.
But the Linux bridge, in VLAN-unaware mode, configures its ports in
promiscuous (IFF_PROMISC) mode, so that they accept packets with any
MAC DA (a switch must do this in order to forward those packets which
are not directly targeted to its MAC address).
As a result, the stmmac driver does not work as a bridge port, when the
kernel is compiled with CONFIG_BRIDGE_VLAN_FILTERING=y.
$ ip link add br0 type bridge && ip link set br0 up
$ ip link set eth0 master br0 && ip link set eth0 up
[ 2333.943296] br0: port 1(eth0) entered blocking state
[ 2333.943381] br0: port 1(eth0) entered disabled state
[ 2333.943782] device eth0 entered promiscuous mode
[ 2333.944080] 4033c000.ethernet eth0: Adding VLAN in promisc mode not supported
[ 2333.976509] 4033c000.ethernet eth0: failed to initialize vlan filtering on this port
RTNETLINK answers: Operation not permitted
Secondly, take the case of stmmac as DSA master. Some switch tagging
protocols are based on 802.1Q VLANs (tag_sja1105.c), and as such,
tag_8021q.c uses vlan_vid_add() to work with VLAN-filtering DSA masters.
But also, when a DSA port becomes promiscuous (for example when it joins
a bridge), the DSA framework also makes the DSA master promiscuous.
Moreover, for every VLAN that a DSA switch sends to the CPU, DSA also
programs a VLAN filter on the DSA master, because if the the DSA switch
uses a tail tag, then the hardware frame parser of the DSA master will
see VLAN as VLAN, and might filter them out, for being unknown.
Due to the above 2 reasons, my belief is that the stmmac driver does not
get to choose to not accept vlan_vid_add() calls while IFF_PROMISC is
enabled, because the 2 are completely independent and there are code
paths in the network stack which directly lead to this situation
occurring, without the user's direct input.
In fact, my belief is that "VLAN promiscuous" mode should have never
been keyed on IFF_PROMISC in the first place, but rather, on the
NETIF_F_HW_VLAN_CTAG_FILTER feature flag which can be toggled by the
user through ethtool -k, when present in netdev->hw_features.
In the stmmac driver, NETIF_F_HW_VLAN_CTAG_FILTER is only present in
"features", making this feature "on [fixed]".
I have this belief because I am unaware of any definition of promiscuity
which implies having an effect on anything other than MAC DA (therefore
not VLAN). However, I seem to be rather alone in having this opinion,
looking back at the disagreements from this discussion:
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
In any case, to remove the vlan_vid_add() dependency on !IFF_PROMISC,
one would need to remove the check and see what fails. I guess the test
was there because of the way in which dwmac4_vlan_promisc_enable() is
implemented.
For context, the dwmac4 supports Perfect Filtering for a limited number
of VLANs - dwmac4_get_num_vlan(), priv->hw->num_vlan, with a fallback on
Hash Filtering - priv->dma_cap.vlhash - see stmmac_vlan_update(), also
visible in cat /sys/kernel/debug/stmmaceth/eth0/dma_cap | grep 'VLAN
Hash Filtering'.
The perfect filtering is based on MAC_VLAN_Tag_Filter/MAC_VLAN_Tag_Data
registers, accessed in the driver through dwmac4_write_vlan_filter().
The hash filtering is based on the MAC_VLAN_Hash_Table register, named
GMAC_VLAN_HASH_TABLE in the driver and accessed by dwmac4_update_vlan_hash().
The control bit for enabling hash filtering is GMAC_VLAN_VTHM
(MAC_VLAN_Tag_Ctrl bit VTHM: VLAN Tag Hash Table Match Enable).
Now, the description of dwmac4_vlan_promisc_enable() is that it iterates
through the driver's cache of perfect filter entries (hw->vlan_filter[i],
added by dwmac4_add_hw_vlan_rx_fltr()), and evicts them from hardware by
unsetting their GMAC_VLAN_TAG_DATA_VEN (MAC_VLAN_Tag_Data bit VEN - VLAN
Tag Enable) bit. Then it unsets the GMAC_VLAN_VTHM bit, which disables
hash matching.
This leaves the MAC, according to table "VLAN Match Status" from the
documentation, to always enter these data paths:
VID |VLAN Perfect Filter |VTHM Bit |VLAN Hash Filter |Final VLAN Match
|Match Result | |Match Result |Status
-------|--------------------|---------|-----------------|----------------
VID!=0 |Fail |0 |don't care |Pass
So, dwmac4_vlan_promisc_enable() does its job, but by unsetting
GMAC_VLAN_VTHM, it conflicts with the other code path which controls
this bit: dwmac4_update_vlan_hash(), called through stmmac_update_vlan_hash()
from stmmac_vlan_rx_add_vid() and from stmmac_vlan_rx_kill_vid().
This is, I guess, why dwmac4_add_hw_vlan_rx_fltr() is not allowed to run
after dwmac4_vlan_promisc_enable() has unset GMAC_VLAN_VTHM: because if
it did, then dwmac4_update_vlan_hash() would set GMAC_VLAN_VTHM again,
breaking the "VLAN promiscuity".
It turns out that dwmac4_vlan_promisc_enable() is way too complicated
for what needs to be done. The MAC_Packet_Filter register also has the
VTFE bit (VLAN Tag Filter Enable), which simply controls whether VLAN
tagged packets which don't match the filtering tables (either perfect or
hash) are dropped or not. At the moment, this driver unconditionally
sets GMAC_PACKET_FILTER_VTFE if NETIF_F_HW_VLAN_CTAG_FILTER was detected
through the priv->dma_cap.vlhash capability bits of the device, in
stmmac_dvr_probe().
I would suggest deleting the unnecessarily complex logic from
dwmac4_vlan_promisc_enable(), and simply unsetting GMAC_PACKET_FILTER_VTFE
when becoming IFF_PROMISC, which has the same effect of allowing packets
with any VLAN tags, but has the additional benefit of being able to run
concurrently with stmmac_vlan_rx_add_vid() and stmmac_vlan_rx_kill_vid().
As much as I believe that the VTFE bit should have been exclusively
controlled by NETIF_F_HW_VLAN_CTAG_FILTER through ethtool, and not by
IFF_PROMISC, changing that is not a punctual fix to the problem, and it
would probably break the VFFQ feature added by the later commit e0f9956a3862 ("net: stmmac: Add option for VLAN filter fail queue
enable"). From the commit description, VFFQ needs IFF_PROMISC=on and
VTFE=off in order to work (and this change respects that). But if VTFE
was changed to be controlled through ethtool -k, then a user-visible
change would have been introduced in Intel's scripts (a need to run
"ethtool -k eth0 rx-vlan-filter off" which did not exist before).
The patch was tested with this set of commands:
ip link set eth0 up
ip link add link eth0 name eth0.100 type vlan id 100
ip addr add 192.168.100.2/24 dev eth0.100 && ip link set eth0.100 up
ip link set eth0 promisc on
ip link add link eth0 name eth0.101 type vlan id 101
ip addr add 192.168.101.2/24 dev eth0.101 && ip link set eth0.101 up
ip link set eth0 promisc off
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link set eth0 promisc on
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link del eth0.100
ip link del eth0.101
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we should see them
ip link set eth0 promisc off
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we shouldn't see them
# anymore, but remove the "-p" argument from tcpdump and they're there.
Fixes: c89f44ff10fd ("net: stmmac: Add support for VLAN promiscuous mode") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The failover txq is inited as 16 queues.
when a packet is transmitted from the failover device firstly,
the failover device will select the queue which is returned from
the primary device if the primary device is UP and running.
If the primary device txq is bigger than the default 16,
it can lead to the following warning:
eth0 selects TX queue 18, but real number of TX queues is 16
Fix that by reducing txq number as the non-existent primary-dev does.
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver") Signed-off-by: Faicker Mo <faicker.mo@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When link speed is 10 Mbps and temperature is under -20°C, RTL8168H and
RTL8107E may have rx crc error. Disable phy 10 Mbps pll off to fix this
issue.
Fixes: 6e1d0b898818 ("r8169:add support for RTL8168H and RTL8107E") Signed-off-by: ChunHao Lin <hau@realtek.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a364760002 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e6e ("net: dsa: microchip: update fdb add/del/dump in ksz_common") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch complains that:
drivers/ptp/ptp_qoriq.c ptp_qoriq_probe()
warn: 'base' from ioremap() not released.
Fix this by revising the parameter from 'ptp_qoriq->base' to 'base'.
This is only a bug if ptp_qoriq_init() returns on the
first -ENODEV error path.
For other error paths ptp_qoriq->base and base are the same.
And this change makes the code more readable.
Fixes: 7f4399ba405b ("ptp_qoriq: fix NULL access if ptp dt node missing") Signed-off-by: SongJingyi <u201912584@hust.edu.cn> Reviewed-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230324031406.1895159-1-u201912584@hust.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers") Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / jedix / linux-maple.git / log