As per RFC792, ICMP errors should be sent to the source host.
However, in configurations with Virtual Routing and Forwarding tables,
looking up which routing table to use is currently done by using the
destination net_device.
commit 9d1a6c4ea43e ("net: icmp_route_lookup should use rt dev to
determine L3 domain") changes the interface passed to
l3mdev_master_ifindex() and inet_addr_type_dev_table() from skb_in->dev
to skb_dst(skb_in)->dev. This effectively uses the destination device
rather than the source device for choosing which routing table should be
used to lookup where to send the ICMP error.
Therefore, if the source and destination interfaces are within separate
VRFs, or one in the global routing table and the other in a VRF, looking
up the source host in the destination interface's routing table will
fail if the destination interface's routing table contains no route to
the source host.
One observable effect of this issue is that traceroute does not work in
the following cases:
- Route leaking between global routing table and VRF
- Route leaking between VRFs
Preferably use the source device routing table when sending ICMP error
messages. If no source device is set, fall-back on the destination
device routing table. Else, use the main routing table (index 0).
[ It has been pointed out that a similar issue may exist with ICMP
errors triggered when forwarding between network namespaces. It would
be worthwhile to investigate, but is outside of the scope of this
investigation. ]
[ It has also been pointed out that a similar issue exists with
unreachable / fragmentation needed messages, which can be triggered by
changing the MTU of eth1 in r1 to 1400 and running:
ip netns exec h1 ping -s 1450 -Mdo -c1 172.16.2.2
Some investigation points to raw_icmp_error() and raw_err() as being
involved in this last scenario. The focus of this patch is TTL expired
ICMP messages, which go through icmp_route_lookup.
Investigation of failure modes related to raw_icmp_error() is beyond
this investigation's scope. ]
Fixes: 9d1a6c4ea43e ("net: icmp_route_lookup should use rt dev to determine L3 domain") Link: https://tools.ietf.org/html/rfc792 Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is one use-after-free in ip_check_mc_rcu.
In ip_mc_del_src, the ip_sf_list of pmc has been freed under pmc->lock protection.
But access to ip_sf_list in ip_check_mc_rcu is not protected by the lock.
Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec8536580 ("ARM: imx: add missing clk_disable_unprepare()") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.
Fixes: ec16dae5453e ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams") Cc: stable@vger.kernel.org Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the backport of commit bdcf1dc25324 ("clk: Evict unregistered clks
from parent caches") to the 4.19.y and 4.14.y stable trees, the
orphan_list structure was placed in the wrong location, causing loads of
build warnings on systems that do not define CONFIG_DEBUG_FS.
Fix this up by moving the structure to the correct place in the file.
Syzkaller reported a divide error in snd_pcm_lib_ioctl. fifo_size
is of type snd_pcm_uframes_t(unsigned long). If frame_size
is 0x100000000, the error occurs.
The system currently warns if the config conditions for
building return_address in arch/arm/kernel/return_address.c
are not met, leaving just an EXPORT_SYMBOL_GPL(return_address)
of a function defined to be 'static linline'.
This is a result of aeea3592a13b ("ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h").
Since we're not going to build anything other than an exported
symbol for something that is already being defined to be an
inline-able return of NULL, just avoid building the code to
remove the following warning:
Fixes: aeea3592a13b ("ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h") Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for cryptoloop has been officially marked broken and deprecated
in favor of dm-crypt (which supports the same broken algorithms if
needed) in Linux 2.6.4 (released in March 2004), and support for it has
been entirely removed from losetup in util-linux 2.23 (released in April
2013). Add a warning and a deprecation schedule.
Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Reported-by: Kees Cook <keescook@chromium.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The location of the system.data extended attribute can change whenever
xattr_sem is not taken. So we need to recalculate the i_inline_off
field since it mgiht have changed between ext4_write_begin() and
ext4_write_end().
This means that caching i_inline_off is probably not helpful, so in
the long run we should probably get rid of it and shrink the in-memory
ext4 inode slightly, but let's fix the race the simple way for now.
Cc: stable@kernel.org Fixes: f19d5870cbf72 ("ext4: add normal write support for inline data") Reported-by: syzbot+13146364637c7363a7de@syzkaller.appspotmail.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common implementation of isatty(3) involves calling a ioctl passing
a dummy struct argument and checking whether the syscall failed --
bionic and glibc use TCGETS (passing a struct termios), and musl uses
TIOCGWINSZ (passing a struct winsize). If the FD is a socket, we will
copy sizeof(struct ifreq) bytes of data from the argument and return
-EFAULT if that fails. The result is that the isatty implementations
may return a non-POSIX-compliant value in errno in the case where part
of the dummy struct argument is inaccessible, as both struct termios
and struct winsize are smaller than struct ifreq (at least on arm64).
Although there is usually enough stack space following the argument
on the stack that this did not present a practical problem up to now,
with MTE stack instrumentation it's more likely for the copy to fail,
as the memory following the struct may have a different tag.
Fix the problem by adding an early check for whether the ioctl is a
valid socket ioctl, and return -ENOTTY if it isn't.
Fixes: 44c02a2c3dc5 ("dev_ioctl(): move copyin/copyout to callers") Link: https://linux-review.googlesource.com/id/I869da6cf6daabc3e4b7b82ac979683ba05e27d4d Signed-off-by: Peter Collingbourne <pcc@google.com> Cc: <stable@vger.kernel.org> # 4.19 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch breaks userspace implementations (e.g. fdutils) and introduces
regressions in behaviour. Previously, it was possible to O_NDELAY open a
floppy device with no media inserted or with write protected media without
an error. Some userspace tools use this particular behavior for probing.
It's not the first time when we revert this patch. Previous revert is in
commit f2791e7eadf4 (Revert "floppy: refactor open() flags handling").
Mark NX as being used for all non-nested shadow MMUs, as KVM will set the
NX bit for huge SPTEs if the iTLB mutli-hit mitigation is enabled.
Checking the mitigation itself is not sufficient as it can be toggled on
at any time and KVM doesn't reset MMU contexts when that happens. KVM
could reset the contexts, but that would require purging all SPTEs in all
MMUs, for no real benefit. And, KVM already forces EFER.NX=1 when TDP is
disabled (for WP=0, SMEP=1, NX=0), so technically NX is never reserved
for shadow MMUs.
Fixes: b8e8c8303ff2 ("kvm: mmu: ITLB_MULTIHIT mitigation") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622175739.3610207-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sudip: use old path and adjust context] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A fb_ioctl() FBIOPUT_VSCREENINFO call with invalid xres setting
or yres setting in struct fb_var_screeninfo will result in a
KASAN: vmalloc-out-of-bounds failure in bitfill_aligned() as
the margins are being cleared. The margins are cleared in
chunks and if the xres setting or yres setting is a value of
zero upto the chunk size, the failure will occur.
Add a margin check to validate xres and yres settings.
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba6b ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org> Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
If the endpoint completion callback is call right after the ep_enabled flag
is cleared and before usb_ep_dequeue() is call, we could do a double free
on the request and the associated buffer.
Fix this by clearing ep_enabled after all the endpoint requests have been
dequeued.
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab225 ("drivers: net: xgene-v2: Add MDIO support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Validate csum_start in gre_handle_offloads before we call _gre_xmit so
that we do not crash later when the csum_start value is used in the
lco_csum function call.
This patch deals with ipv4 code.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot+ff8e1b9f2f36481e2efc@syzkaller.appspotmail.com Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23aa ("e1000e: add support for LTR on I217/I218") Suggested-by: Yee Li <seven.yi.lee@gmail.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so") Cc: <stable@vger.kernel.org> Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device") Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu Cc: stable@vger.kernel.org Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Reported-by: Minmin chen <chenmingmin@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
However, as a runtime result, we get 2 instead of 1, meaning the dst
register does not contain (u32)-1 in this case. The reason is fairly
straight forward given the 0 test leaves the dst register as-is:
# ./bpftool p d x i 23
0: (b7) r0 = 0
1: (b7) r1 = -1
2: (b4) w2 = -1
3: (16) if w0 == 0x0 goto pc+1
4: (9c) w1 %= w0
5: (b7) r0 = 1
6: (1d) if r1 == r2 goto pc+1
7: (b7) r0 = 2
8: (95) exit
This was originally not an issue given the dst register was marked as
completely unknown (aka 64 bit unknown). However, after 468f6eafa6c4
("bpf: fix 32-bit ALU op verification") the verifier casts the register
output to 32 bit, and hence it becomes 32 bit unknown. Note that for
the case where the src register is unknown, the dst register is marked
64 bit unknown. After the fix, the register is truncated by the runtime
and the test passes:
Fixes: 468f6eafa6c4 ("bpf: fix 32-bit ALU op verification") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com>
[Salvatore Bonaccorso: This is an earlier version based on work by
Daniel and John which does not rely on availability of the BPF_JMP32
instruction class. This means it is not even strictly a backport of the
upstream commit mentioned but based on Daniel's and John's work to
address the issue and was finalized by Thadeu Lima de Souza Cascardo.] Tested-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reviewing a different fix, John and I noticed an oddity in one of the
BPF program dumps that stood out, for example:
# bpftool p d x i 13
0: (b7) r0 = 808464450
1: (b4) w4 = 808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
[...]
In line 2 we noticed that the mov32 would 32 bit truncate the original src
register for the div/mod operation. While for the two operations the dst
register is typically marked unknown e.g. from adjust_scalar_min_max_vals()
the src register is not, and thus verifier keeps tracking original bounds,
simplified:
Runtime result of r0 at exit is 0 instead of expected -1. Remove the
verifier mov32 src rewrite in div/mod and replace it with a jmp32 test
instead. After the fix, we result in the following code generation when
having dividend r1 and divisor r6:
x86 in particular can throw a 'divide error' exception for div
instruction not only for divisor being zero, but also for the case
when the quotient is too large for the designated register. For the
edx:eax and rdx:rax dividend pair it is not an issue in x86 BPF JIT
since we always zero edx (rdx). Hence really the only protection
needed is against divisor being zero.
Fixes: 68fda450a7df ("bpf: fix 32-bit divide by zero") Co-developed-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
[Salvatore Bonaccorso: This is an earlier version of the patch provided
by Daniel Borkmann which does not rely on availability of the BPF_JMP32
instruction class. This means it is not even strictly a backport of the
upstream commit mentioned but based on Daniel's and John's work to
address the issue.] Tested-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Fri, 27 Aug 2021 13:55:31 +0000 (10:55 -0300)]
bpf: Do not use ax register in interpreter on div/mod
Partially undo old commit 144cd91c4c2b ("bpf: move tmp variable into ax
register in interpreter"). The reason we need this here is because ax
register will be used for holding temporary state for div/mod instruction
which otherwise interpreter would corrupt. This will cause a small +8 byte
stack increase for interpreter, but with the gain that we can use it from
verifier rewrites as scratch register.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com>
[cascardo: This partial revert is needed in order to support using AX for
the following two commits, as there is no JMP32 on 4.19.y] Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got a problem on MIPS with Big-Endian is turned on: every time when
NF trying to change TCP MSS it returns because of new.v16 was greater
than old.v16. But real MSS was 1460 and my rule was like this:
add rule table chain tcp option maxseg size set 1400
And 1400 is lesser that 1460, not greater.
Later I founded that main causer is cast from u32 to __be16.
Debugging:
In example MSS = 1400(HEX: 0x578). Here is representation of each byte
like it is in memory by addresses from left to right(e.g. [0x0 0x1 0x2
0x3]). LE — Little-Endian system, BE — Big-Endian, left column is type.
LE BE
u32: [78 05 00 00] [00 00 05 78]
As you can see, u32 representation will be casted to u16 from different
half of 4-byte address range. But actually nf_tables uses registers and
store data of various size. Actually TCP MSS stored in 2 bytes. But
registers are still u32 in definition:
So, access like regs->data[priv->sreg] exactly u32. So, according to
table presents above, per-byte representation of stored TCP MSS in
register will be:
LE BE
(u32)regs->data[]: [78 05 00 00] [05 78 00 00]
^^ ^^
We see that register uses just half of u32 and other 2 bytes may be
used for some another data. But in nft_exthdr_tcp_set_eval() it casted
just like u32 -> __be16:
new.v16 = src
But u32 overfill __be16, so it get 2 low bytes. For clarity draw
one more table(<xx xx> means that bytes will be used for cast).
LE BE
u32: [<78 05> 00 00] [00 00 <05 78>]
(u32)regs->data[]: [<78 05> 00 00] [05 78 <00 00>]
As you can see, for Little-Endian nothing changes, but for Big-endian we
take the wrong half. In my case there is some other data instead of
zeros, so new MSS was wrongly greater.
For shooting this bug I used solution for ports ranges. Applying of this
patch does not affect Little-Endian systems.
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 9e8925b67a ("locks: Allow disabling mandatory locking at compile
time"), attempts to mount filesystems with "-o mand" will fail.
Unfortunately, there is no other indiciation of the reason for the
failure.
Change how the function is defined for better readability. When
CONFIG_MANDATORY_FILE_LOCKING is disabled, printk a warning when
someone attempts to mount with -o mand.
Also, add a blurb to the mandatory-locking.txt file to explain about
the "mand" option, and the behavior one should expect when it is
disabled.
Reported-by: Jan Kara <jack@suse.cz> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 2e6b836312a4 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com Signed-off-by: Marcin Bachry <hegel666@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Prike Liang <prike.liang@amd.com> Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cross-rename lacks a check when that would prevent exchanging a
directory and subvolume from different parent subvolume. This causes
data inconsistencies and is caught before commit by tree-checker,
turning the filesystem to read-only.
Calling the renameat2 with RENAME_EXCHANGE flags like
The corrupted data will not be written, and filesystem can be unmounted
and mounted again (all changes since the last commit will be lost).
Add the missing check for new_ino so that all non-subvolumes must reside
under the same parent subvolume. There's an exception allowing to
exchange two subvolumes from any parents as the directory representing a
subvolume is only a logical link and does not have any other structures
related to the parent subvolume, unlike files, directories etc, that
are always in the inode namespace of the parent subvolume.
Fixes: cdd1fedf8261 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT") CC: stable@vger.kernel.org # 4.7+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error handling code in tpci200_register does not free interface_regs
allocated by ioremap and the current version of error handling code is
problematic.
Fix this by refactoring the error handling code and free interface_regs
when necessary.
Fixes: 43986798fd50 ("ipack: add error handling for ioremap_nocache") Cc: stable@vger.kernel.org Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210810100323.3938492-2-mudongliangabcd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function tpci200_register called by tpci200_install and
tpci200_unregister called by tpci200_uninstall are in pair. However,
tpci200_unregister has some cleanup operations not in the
tpci200_register. So the error handling code of tpci200_pci_probe has
many different double free issues.
Fix this problem by moving those cleanup operations out of
tpci200_unregister, into tpci200_pci_remove and reverting
the previous commit 9272e5d0028d ("ipack/carriers/tpci200:
Fix a double free in tpci200_pci_probe").
Fixes: 9272e5d0028d ("ipack/carriers/tpci200: Fix a double free in tpci200_pci_probe") Cc: stable@vger.kernel.org Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210810100323.3938492-1-mudongliangabcd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During suspend/resume NGD remote instance is power cycled along
with remotely controlled bam dma engine.
So Reset the dma configuration during this suspend resume path
so that we are not dealing with any stale dma setup.
Without this transactions timeout after first suspend resume path.
In some usecases transaction ids are dynamically allocated inside
the controller driver after sending the messages which have generic
acknowledge responses. So check for this before refcounting pm_runtime.
Without this we would end up imbalancing runtime pm count by
doing pm_runtime_put() in both slim_do_transfer() and slim_msg_response()
for a single pm_runtime_get() in slim_do_transfer()
As tid is unsigned its hard to figure out if the tid is valid or
invalid. So Start the transaction ids from 1 instead of zero
so that we could differentiate between a valid tid and invalid tids
This is useful in cases where controller would add a tid for controller
specific transfers.
The problem was the "trace(read_max,count)" where the "count" should be
"$count" as "onmax()" only handles variables (although it really should be
able to figure out that "count" is a field of sys_enter_read). But there's
a path that does not find the variable and ends up passing a NULL for the
event, which ends up getting passed to "strcmp()".
Add a check for NULL to return and error on the command with:
The original code in the cap_put_caller() function does not
handle correctly the positive values returned from the passed
function for multiple iterations. It means that the change
notifications may be lost.
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.") Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose") Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
qlcnic_83xx_unlock_flash() is called on all paths after we call
qlcnic_83xx_lock_flash(), except for one error path on failure
of QLCRD32(), which may cause a deadlock. This bug is suggested
by a static analysis tool, please advise.
Fixes: 81d0aeb0a4fff ("qlcnic: flash template based firmware reset recovery") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20210816131405.24024-1-dinghao.liu@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb044 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown") Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the incorrect calculation for integer overflow
when the last address of iova range is 0xffffffff.
Fixes: ec33d031a14b ("vhost: detect 32 bit integer wrap around") Reported-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Xie Yongji <xieyongji@bytedance.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20210728130756.97-2-xieyongji@bytedance.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC complains about empty macros in an 'if' statement, so convert
them to 'do {} while (0)' macros.
Fixes these build warnings:
net/dccp/output.c: In function 'dccp_xmit_packet':
../net/dccp/output.c:283:71: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
283 | dccp_pr_debug("transmit_skb() returned err=%d\n", err);
net/dccp/ackvec.c: In function 'dccp_ackvec_update_old':
../net/dccp/ackvec.c:163:80: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
163 | (unsigned long long)seqno, state);
Fixes: dc841e30eaea ("dccp: Extend CCID packet dequeueing interface") Fixes: 380240864451 ("dccp ccid-2: Update code for the Ack Vector input/registration routine") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: dccp@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 1.2 GHz variant of the Armada 3720 SOC is unstable with DVFS: when
the SOC boots, the WTMI firmware sets clocks and AVS values that work
correctly with 1.2 GHz CPU frequency, but random crashes occur once
cpufreq driver starts scaling.
We do not know currently what is the reason:
- it may be that the voltage value for L0 for 1.2 GHz variant provided
by the vendor in the OTP is simply incorrect when scaling is used,
- it may be that some delay is needed somewhere,
- it may be something else.
The most sane solution now seems to be to simply forbid the cpufreq
driver on 1.2 GHz variant.
Signed-off-by: Marek Behún <kabel@kernel.org> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and dead000000000200 is LIST_POISON2.
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Avoid printing a 'target allocation failed' error if the driver
target_alloc() callback function returns -ENXIO. This return value
indicates that the corresponding H:C:T:L entry is empty.
Removing this error reduces the scan time if the user issues SCAN_WILD_CARD
scan operation through sysfs parameter on a host with a lot of empty
H:C:T:L entries.
Avoiding the printk on -ENXIO matches the behavior of the other callback
functions during scanning.
Fix the race between rdac_bus_attach() and rdac_bus_detach() where h->sdev
is NULL when processing the RDAC attach.
Link: https://lore.kernel.org/r/20210113063103.2698953-1-yebin10@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The list_for_each_entry() iterator, "adapter" in this code, can never be
NULL. If we exit the loop without finding the correct adapter then
"adapter" points invalid memory that is an offset from the list head. This
will eventually lead to memory corruption and presumably a kernel crash.
Link: https://lore.kernel.org/r/20210708074642.23599-1-harshvardhan.jha@oracle.com Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the router_xlate can not find the controller in the available DMA
devices then it should return with -EPORBE_DEFER in a same way as the
of_dma_request_slave_channel() does.
The issue can be reproduced if the event router is registered before the
DMA controller itself and a driver would request for a channel before the
controller is registered.
In of_dma_request_slave_channel():
1. of_dma_find_controller() would find the dma_router
2. ofdma->of_dma_xlate() would fail and returned NULL
3. -ENODEV is returned as error code
with this patch we would return in this case the correct -EPROBE_DEFER and
the client can try to request the channel later.
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by moving the error_pm label above the pm_runtime_put() in
the error path.
When user calls dmaengine_terminate_sync, the driver will clean up any
remaining descriptors for all the pending or active transfers that had
previously been submitted. However, this might happen whilst the tasklet is
invoking the DMA callback for the last finished transfer, so by the time it
returns and takes over the channel's spinlock, the list of completed
descriptors it was traversing is no longer valid. This leads to a
read-after-free situation.
Fix it by signalling whether a user-triggered termination has happened by
means of a boolean variable.
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
tkip_keymap can be used internally to avoid the reference to key->cipher
and with this, only the key index value itself is needed. This allows
ath_key_delete() call to be postponed to be handled after the upper
layer STA and key entry have already been removed. This is needed to
make ath9k key cache management safer.
Now that ath/key.c may not be explicitly clearing keys from the key
cache, clear all key cache entries when disabling hardware to make sure
no keys are left behind beyond this point.
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
The XSAVE init code initializes all enabled and supported components with
XRSTOR(S) to init state. Then it XSAVEs the state of the components back
into init_fpstate which is used in several places to fill in the init state
of components.
This works correctly with XSAVE, but not with XSAVEOPT and XSAVES because
those use the init optimization and skip writing state of components which
are in init state. So init_fpstate.xsave still contains all zeroes after
this operation.
There are two ways to solve that:
1) Use XSAVE unconditionally, but that requires to reshuffle the buffer when
XSAVES is enabled because XSAVES uses compacted format.
2) Save the components which are known to have a non-zero init state by other
means.
Looking deeper, #2 is the right thing to do because all components the
kernel supports have all-zeroes init state except the legacy features (FP,
SSE). Those cannot be hard coded because the states are not identical on all
CPUs, but they can be saved with FXSAVE which avoids all conditionals.
Use FXSAVE to save the legacy FP/SSE components in init_fpstate along with
a BUILD_BUG_ON() which reminds developers to validate that a newly added
component has all zeroes init state. As a bonus remove the now unused
copy_xregs_to_kernel_booting() crutch.
The XSAVE and reshuffle method can still be implemented in the unlikely
case that components are added which have a non-zero init state and no
other means to save them. For now, FXSAVE is just simple and good enough.
[ bp: Fix a typo or two in the text. ]
Fixes: 6bad06b76892 ("x86, xsave: Use xsaveopt in context-switch path when supported") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20210618143444.587311343@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Invert the mask of bits that we pick from L2 in
nested_vmcb02_prepare_control
* Invert and explicitly use VIRQ related bits bitmask in svm_clear_vintr
This fixes a security issue that allowed a malicious L1 to run L2 with
AVIC enabled, which allowed the L2 to exploit the uninitialized and enabled
AVIC to read/write the host physical memory at some offsets.
If L1 disables VMLOAD/VMSAVE intercepts, and doesn't enable
Virtual VMLOAD/VMSAVE (currently not supported for the nested hypervisor),
then VMLOAD/VMSAVE must operate on the L1 physical memory, which is only
possible by making L0 intercept these instructions.
Failure to do so allowed the nested guest to run VMLOAD/VMSAVE unintercepted,
and thus read/write portions of the host physical memory.
If we know that we have an encrypted link (based on having had
a key configured for TX in the past) then drop all data frames
in the key selection handler if there's no key anymore.
This fixes an issue with mac80211 internal TXQs - there we can
buffer frames for an encrypted link, but then if the key is no
longer there when they're dequeued, the frames are sent without
encryption. This happens if a station is disconnected while the
frames are still on the TXQ.
Detecting that a link should be encrypted based on a first key
having been configured for TX is fine as there are no use cases
for a connection going from with encryption to no encryption.
With extended key IDs, however, there is a case of having a key
configured for only decryption, so we can't just trigger this
behaviour on a key being configured.
Cc: stable@vger.kernel.org Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200326150855.6865c7f28a14.I9fb1d911b064262d33e33dfba730cdeef83926ca@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[pali: Backported to 4.19 and older versions] Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IOMMU driver calculates the guest addressability for a DMA request
based on the value of the mgaw reported from the IOMMU. However, this
is a fused value and as mentioned in the spec, the guest width
should be calculated based on the minimum of supported adjusted guest
address width (SAGAW) and MGAW.
This is from specification:
"Guest addressability for a given DMA request is limited to the
minimum of the value reported through this field and the adjusted
guest address width of the corresponding page-table structure.
(Adjusted guest address widths supported by hardware are reported
through the SAGAW field)."
This causes domain initialization to fail and following
errors appear for EHCI PCI driver:
[ 2.486393] ehci-pci 0000:01:00.4: EHCI Host Controller
[ 2.486624] ehci-pci 0000:01:00.4: new USB bus registered, assigned bus
number 1
[ 2.489127] ehci-pci 0000:01:00.4: DMAR: Allocating domain failed
[ 2.489350] ehci-pci 0000:01:00.4: DMAR: 32bit DMA uses non-identity
mapping
[ 2.489359] ehci-pci 0000:01:00.4: can't setup: -12
[ 2.489531] ehci-pci 0000:01:00.4: USB bus 1 deregistered
[ 2.490023] ehci-pci 0000:01:00.4: init 0000:01:00.4 fail, -12
[ 2.490358] ehci-pci: probe of 0000:01:00.4 failed with error -12
This issue happens when the value of the sagaw corresponds to a
48-bit agaw. This fix updates the calculation of the agaw based on
the minimum of IOMMU's sagaw value and MGAW.
This issue happens on the code path of getting a private domain for a
device. A private domain was needed when the domain of an iommu group
couldn't meet the requirement of a device. The IOMMU core has been
evolved to eliminate the need for private domain, hence this code path
has alreay been removed from the upstream since commit 327d5b2fee91c
("iommu/vt-d: Allow 32bit devices to uses DMA domain"). Instead of back
porting all patches that are required for removing the private domain,
this simply fixes it in the affected stable kernel between v4.16 and v5.7.
[baolu: The orignal patch could be found here
https://lore.kernel.org/linux-iommu/20210412202736.70765-1-saeed.mirzamohammadi@oracle.com/.
I added commit message according to Greg's comments at
https://lore.kernel.org/linux-iommu/YHZ%2FT9x7Xjf1r6fI@kroah.com/.]
A recent change in LLVM causes module_{c,d}tor sections to appear when
CONFIG_K{A,C}SAN are enabled, which results in orphan section warnings
because these are not handled anywhere:
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_ctor) is being placed in '.text.asan.module_ctor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_dtor) is being placed in '.text.asan.module_dtor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.tsan.module_ctor) is being placed in '.text.tsan.module_ctor'
Fangrui explains: "the function asan.module_ctor has the SHF_GNU_RETAIN
flag, so it is in a separate section even with -fno-function-sections
(default)".
Place them in the TEXT_TEXT section so that these technologies continue
to work with the newer compiler versions. All of the KASAN and KCSAN
KUnit tests continue to pass after this change.
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Reported-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log