Currently the driver prevents a user from doing
modprobe ice
ethtool -L eth0 combined 5
ip link set eth0 up
The ethtool command fails, because the driver is checking to see if the
interface is down before allowing the get_channels to proceed (even for
a set_channels).
Remove this check and allow the user to configure the interface
before bringing it up, which is a much better usability case.
Fixes: 87324e747fde ("ice: Implement ethtool ops for channels") Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Overflowed requests in io_uring_cancel_files() should be shed only of
inflight and overflowed refs. All other left references are owned by
someone else.
If refcount_sub_and_test() fails, it will go further and put put extra
ref, don't do that. Also, don't need to do io_wq_cancel_work()
for overflowed reqs, they will be let go shortly anyway.
ColdFire is a big-endian cpu with a big-endian dspi hw module,
so, it uses native access, but memcpy breaks the endianness.
So, if i understand properly, by native copy we would mean
be(cpu)->be(dspi) or le(cpu)->le(dspi) accesses, so my fix
shouldn't break anything, but i couldn't test it on LS family,
so every test is really appreciated.
Fixes: 53fadb4d90c7 ("spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics") Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20200529195756.184677-1-angelo.dureghello@timesys.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Previous commit "b8eb718348b8" fixed a similar problem.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
[ rjw: Subject ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
When mvm is initialized we alloc aux station with aux queue.
We later free the station memory when driver is stopped, but we
never free the queue's memory, which casues a leak.
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using a fixed 1s timeout for all commands (and data transfers) is a bit
problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
For commands that doesn't involve to prepare a data transfer, owl-mmc is
using a fixed 30s response timeout. This is a bit problematic.
For some commands it means waiting longer than needed for the completion to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
30s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Using a fixed 1s timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the timeout to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Instead of reimplementing the logic in mmc_regulator_set_vqmmc(), use the
mmc code function directly.
This also allows us to fix a related issue on STM32MP1, when a voltage
switch of 1.8V is done for the eMMC, but the current level is already set
to 1.8V. More precisely, in this scenario the call to the
->post_sig_volt_switch() hangs, indefinitely waiting for the voltage switch
to complete. Fix this problem by checking if mmc_regulator_set_vqmmc()
returned 1 and then skip invoking the callback.
At line 808, put_disk(disk) may encounter kobject refcount of 'disk'
being underflow.
Here is how to reproduce the issue,
- Attche the backing device to a cache device and do random write to
make the cache being dirty.
- Stop the bcache device while the cache device has dirty data of the
backing device.
- Only register the backing device back, NOT register cache device.
- The bcache device node /dev/bcache0 won't show up, because backing
device waits for the cache device shows up for the missing dirty
data.
- Now echo 1 into /sys/fs/bcache/pendings_cleanup, to stop the pending
backing device.
- After the pending backing device stopped, use 'dmesg' to check kernel
message, a use-after-free warning from KASA reported the refcount of
kobject linked to the 'disk' is underflow.
The dropping refcount at line 808 in the above code piece is added by
add_disk(d->disk) in bch_cached_dev_run(). But in the above condition
the cache device is not registered, bch_cached_dev_run() has no chance
to be called and the refcount is not added. The put_disk() for a non-
added refcount of gendisk kobject triggers a underflow warning.
This patch checks whether GENHD_FL_UP is set in disk->flags, if it is
not set then the bcache device was not added, don't call put_disk()
and the the underflow issue can be avoided.
Register "a1" is unsaved in this function,
when CONFIG_TRACE_IRQFLAGS is enabled,
the TRACE_IRQS_OFF macro will call trace_hardirqs_off(),
and this may change register "a1".
The changed register "a1" as argument will be send
to do_fpe() and do_msa_fpe().
Ignore loopback-originatig packets soon enough and don't try to process L2
header where it doesn't exist. The very similar br_handle_frame() in bridge
code performs exactly the same check.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing a namespace, we add an NS_CHANGE async event, however if
the controller admin queue is removed after the event was added but not
yet processed, we won't free the aens, resulting in the below memory
leak [1].
Fix that by moving nvmet_async_event_free to the final controller
release after it is detached from subsys->ctrls ensuring no async
events are added, and modify it to simply remove all pending aens.
Currently, changing the brightness of the internal display of the Acer
TravelMate 5735Z does not work. Pressing the function keys or changing the
slider, GNOME Shell 3.36.2 displays the OSD (five steps), but the
brightness does not change.
The Acer TravelMate 5735Z shipped with Windows 7 and as such does not
trigger our "win8 ready" heuristic for preferring the native backlight
interface.
Still ACPI backlight control doesn't work on this model, where as the
native (intel_video) backlight interface does work by adding
`acpi_backlight=native` or `acpi_backlight=none` to Linux’ command line.
So, add a quirk to force using native backlight control on this model.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207835 Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[CAUSE]
The problem is in btrfs_qgroup_inherit(), we don't have good enough
check to determine if the new relation would break the existing
accounting.
Unlike btrfs_add_qgroup_relation(), which has proper check to determine
if we can do quick update without a rescan, in btrfs_qgroup_inherit() we
can even assign a snapshot to multiple qgroups.
[FIX]
Fix it by manually marking qgroup inconsistent for snapshot inheritance.
For subvolume creation, since all its extents are exclusively owned, we
don't need to rescan.
In theory, we should call relation check like quick_update_accounting()
when doing qgroup inheritance and inform user about qgroup accounting
inconsistency.
But we don't have good mechanism to relay that back to the user in the
snapshot creation context, thus we can only silently mark the qgroup
inconsistent.
Anyway, user shouldn't use qgroup inheritance during snapshot creation,
and should add qgroup relationship after snapshot creation by 'btrfs
qgroup assign', which has a much better UI to inform user about qgroup
inconsistent and kick in rescan automatically.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For unlink transactions and block group removal
btrfs_start_transaction_fallback_global_rsv will first try to start an
ordinary transaction and if it fails it will fall back to reserving the
required amount by stealing from the global reserve. This is problematic
because of all the same reasons we had with previous iterations of the
ENOSPC handling, thundering herd. We get a bunch of failures all at
once, everybody tries to allocate from the global reserve, some win and
some lose, we get an ENSOPC.
Fix this behavior by introducing BTRFS_RESERVE_FLUSH_ALL_STEAL. It's
used to mark unlink reservation. To fix this we need to integrate this
logic into the normal ENOSPC infrastructure. We still go through all of
the normal flushing work, and at the moment we begin to fail all the
tickets we try to satisfy any tickets that are allowed to steal by
stealing from the global reserve. If this works we start the flushing
system over again just like we would with a normal ticket satisfaction.
This serializes our global reserve stealing, so we don't have the
thundering herd problem.
Reviewed-by: Nikolay Borisov <nborisov@suse.com> Tested-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Thanks to Stan Johnson for capturing the console log and running git
bisect.
Git bisect said commit 8e3a68fb55e0 ("dma-mapping: make
dma_atomic_pool_init self-contained") is the first "bad" commit. I don't
know why. Perhaps mach_l2_flush first became reachable with that commit.
The exception handler subroutines are declared as a single char, but
when copied to the required addresses the copy length is 0x80.
When range checks are enabled for memcpy() this results in a build
failure, with error messages such as:
In file included from arch/mips/mti-malta/malta-init.c:15:
In function 'memcpy',
inlined from 'mips_nmi_setup' at arch/mips/mti-malta/malta-init.c:98:2:
include/linux/string.h:376:4: error: call to '__read_overflow2' declared with attribute error: detected read beyond size of object passed as 2nd parameter
376 | __read_overflow2();
| ^~~~~~~~~~~~~~~~~~
Change the declarations to use type char[].
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: YunQiang Su <syq@debian.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if the iavf is loaded and a VF link transitions from up to
down to up again a Tx timeout will be triggered. This happens because
Tx/Rx queue interrupts are only enabled when receiving the
VIRTCHNL_OP_CONFIG_MAP_IRQ message, which happens on reset or initial
iavf driver load, but not when bringing link up. This is problematic
because they are disabled on the VIRTCHNL_OP_DISABLE_QUEUES message,
which is part of bringing a VF's link down. However, they are not
enabled on the VIRTCHNL_OP_ENABLE_QUEUES message, which is part of
bringing a VF's link up.
Fix this by re-enabling the VF's Rx and Tx queue interrupts when they
were previously configured. This is done by first checking to make
sure the previous value in QINT_[R|T]QCTL.MSIX_INDX is not 0, which
is used to represent the OICR in the VF's interrupt space. If the
MSIX_INDX is non-zero then enable the interrupt by setting the
QINT_[R|T]CTL.CAUSE_ENA bit to 1.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes an intermittent bug where a root PD clear operation still in
progress could overwrite a PDE update done by the CPU, resulting in a
VM fault.
Fixes: 108b4d928c03 ("drm/amd/amdgpu: Update VM function pointer") Reported-by: Jay Cornwall <Jay.Cornwall@amd.com> Tested-by: Jay Cornwall <Jay.Cornwall@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Problem description]
1. Boot up picasso platform, launches desktop, Don't do anything (APU enter into "gfxoff" state)
2. Remote login to platform using SSH, then type the command line:
sudo su -c "echo manual > /sys/class/drm/card0/device/power_dpm_force_performance_level"
sudo su -c "echo 2 > /sys/class/drm/card0/device/pp_dpm_sclk" (fix SCLK to 1400MHz)
3. Move the mouse around in Window
4. Phenomenon : The screen frozen
Tester will switch sclk level during glmark2 run time.
APU will enter "gfxoff" state intermittently during glmark2 run time.
The system got hanged if fix GFXCLK to 1400MHz when APU is in "gfxoff"
state.
[Debug]
1. Fix SCLK to X MHz
1400: screen frozen, screen black, then OS will reboot.
1300: screen frozen.
1200: screen frozen, screen black.
1100: screen frozen, screen black, then OS will reboot.
1000: screen frozen, screen black.
900: screen frozen, screen black, then OS will reboot.
800: Situation Nomal, issue disappear.
700: Situation Nomal, issue disappear.
2. SBIOS setting: AMD CBS --> SMU Debug Options -->SMU Debug --> "GFX DLDO Psm Margin Control":
50 : Situation Nomal, issue disappear.
45 : Situation Nomal, issue disappear.
40 : Situation Nomal, issue disappear.
35 : Situation Nomal, issue disappear.
30 : screen black.
25 : screen frozen, then blurred screen.
20 : screen frozen.
15 : screen black.
10 : screen frozen.
5 : screen frozen, then blurred screen.
3. Disable GFXOFF feature
Situation Nomal, issue disappear.
[Why]
Through a period of time debugging with Sys Eng team and SMU team, Sys
Eng team said this is voltage/frequency marginal issue not a F/W or H/W
bug. This experiment proves that default targetPsm [for f=1400MHz] is
not sufficient when GFXOFF is enabled on Picasso.
SMU team think it is an odd test conditions to force sclk="1400MHz" when
GPU is in "gfxoff" state，then wake up the GFX. SCLK should be in the
"lowest frequency" when gfxoff.
[How]
Disable gfxoff when setting manual mode.
Enable gfxoff when setting other mode(exiting manual mode) again.
By the way, from the user point of view, now that user switch to manual
mode and force SCLK Frequency, he don't want SCLK be controlled by
workload.It becomes meaningless to "switch to manual mode" if APU enter "gfxoff"
due to lack of workload at this point.
Tips: Same issue observed on Raven.
Signed-off-by: chen gong <curry.gong@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix wrong crc32 initialisation value:
"alg: shash: stm32_crc32 test failed (wrong result) on test vector 0,
cfg="init+update+final aligned buffer"
cra_name="crc32c" expects an init value of 0XFFFFFFFF,
cra_name="crc32" expects an init value of 0.
Fixes: b51dbe90912a ("crypto: stm32 - Support for STM32 CRC32 crypto module") Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@st.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Loops-per-jiffies is a special number which represents a number of
noop-loop cycles per CPU-scheduler quantum - jiffies. As you
understand aside from CPU-specific implementation it depends on
the CPU frequency. So when a platform has the CPU frequency fixed,
we have no problem and the current udelay interface will work
just fine. But as soon as CPU-freq driver is enabled and the cores
frequency changes, we'll end up with distorted udelay's. In order
to fix this we have to accordinly adjust the per-CPU udelay_val
(the same as the global loops_per_jiffy) number. This can be done
in the CPU-freq transition event handler. We subscribe to that event
in the MIPS arch time-inititalization method.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: devicetree@vger.kernel.org Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocated in the ice_add_prof_id_vsig() function wasn't being
properly freed if an error occurred inside the for-loop in the function.
In particular, 'p' wasn't being freed if an error occurred before it was
added to the resource list at the end of the for-loop.
Signed-off-by: Eric Joyner <eric.joyner@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The vf_id variable is dealt with in the code in inconsistent
ways of sign usage, preventing compilation with -Werror=sign-compare.
Fix this problem in the code by always treating vf_id as unsigned, since
there are no valid values of vf_id that are negative.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Indeed according to the MIPS32 Privileged Resource Architecgture the MAAR
pair register address field either takes [12:31] bits for non-XPA systems
and [12:55] otherwise. In any case the current address mask is just
wrong for 64-bit and 32-bits XPA chips. So lets extend it to 59-bits
of physical address value. This shall cover the 64-bits architecture and
systems with XPA enabled, and won't cause any problem for non-XPA 32-bit
systems, since address values exceeding the architecture specific MAAR
mask will be just truncated with setting zeros in the unsupported upper
bits.
When users write some huge number into cpu.cfs_quota_us or
cpu.rt_runtime_us, overflow might happen during to_ratio() shifts of
schedulable checks.
to_ratio() could be altered to avoid unnecessary internal overflow, but
min_cfs_quota_period is less than 1 << BW_SHIFT, so a cutoff would still
be needed. Set a cap MAX_BW for cfs_quota_us and rt_runtime_us to
prevent overflow.
The attr fork can transition from shortform to leaf format while
empty if the first xattr doesn't fit in shortform. While this empty
leaf block state is intended to be transient, it is technically not
due to the transactional implementation of the xattr set operation.
We historically have a couple of bandaids to work around this
problem. The first is to hold the buffer after the format conversion
to prevent premature writeback of the empty leaf buffer and the
second is to bypass the xattr count check in the verifier during
recovery. The latter assumes that the xattr set is also in the log
and will be recovered into the buffer soon after the empty leaf
buffer is reconstructed. This is not guaranteed, however.
If the filesystem crashes after the format conversion but before the
xattr set that induced it, only the format conversion may exist in
the log. When recovered, this creates a latent corrupted state on
the inode as any subsequent attempts to read the buffer fail due to
verifier failure. This includes further attempts to set xattrs on
the inode or attempts to destroy the attr fork, which prevents the
inode from ever being removed from the unlinked list.
To avoid this condition, accept that an empty attr leaf block is a
valid state and remove the count check from the verifier. This means
that on rare occasions an attr fork might exist in an unexpected
state, but is otherwise consistent and functional. Note that we
retain the logic to avoid racing with metadata writeback to reduce
the window where this can occur.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
6d92bc9d483a ("x86/build: Build compressed x86 kernels as PIE"),
pre-2.26 binutils generates R_386_32 relocations in PIE mode. Since the
startup code does not perform relocation, any reloc entry with R_386_32
will remain as 0 in the executing code.
Commit
974f221c84b0 ("x86/boot: Move compressed kernel to the end of the
decompression buffer")
added a new symbol _end but did not mark it hidden, which doesn't give
the correct offset on older linkers. This causes the compressed kernel
to be copied beyond the end of the decompression buffer, rather than
flush against it. This region of memory may be reserved or already
allocated for other purposes by the bootloader.
Mark _end as hidden to fix. This changes the relocation from R_386_32 to
R_386_RELATIVE even on the pre-2.26 binutils.
For 64-bit, this is not strictly necessary, as the 64-bit kernel is only
built as PIE if the linker supports -z noreloc-overflow, which implies
binutils-2.27+, but for consistency, mark _end as hidden here too.
The below illustrates the before/after impact of the patch using
binutils-2.25 and gcc-4.6.4 (locally compiled from source) and QEMU.
Dump from extract_kernel before patch:
early console in extract_kernel
input_data: 0x0207c098 <--- this is at output + init_size
input_len: 0x0074fef1
output: 0x01000000
output_len: 0x00fa63d0
kernel_total_size: 0x0107c000
needed_size: 0x0107c000
Dump from extract_kernel after patch:
early console in extract_kernel
input_data: 0x0190d098 <--- this is at output + init_size - _end
input_len: 0x0074fef1
output: 0x01000000
output_len: 0x00fa63d0
kernel_total_size: 0x0107c000
needed_size: 0x0107c000
Fixes: 974f221c84b0 ("x86/boot: Move compressed kernel to the end of the decompression buffer") Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20200207214926.3564079-1-nivedita@alum.mit.edu Signed-off-by: Sasha Levin <sashal@kernel.org>
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static] Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mwifiex_cfg80211_dump_station() uses static variable for iterating
over a linked list of all associated stations (when the driver is in UAP
role). This has a race condition if .dump_station is called in parallel
for multiple interfaces. This corruption can be triggered by registering
multiple SSIDs and calling, in parallel for multiple interfaces
iw dev <iface> station dump
This patch drops the use of the static iterator, and instead every time
the function is called iterates to the idx-th position of the
linked-list.
It would be better to convert the code not to use linked list for
associated stations storage (since the chip has a limited number of
associated stations anyway - it could just be an array). Such a change
may be proposed in the future. In the meantime this patch can backported
into stable kernels in this simple form.
Fixes: 8baca1a34d4c ("mwifiex: dump station support in uap mode") Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200515075924.13841-1-pali@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Seven years ago we tried to fix a leak but actually introduced a double
free instead. It was an understandable mistake because the code was a
bit confusing and the free was done in the wrong place. The "skb"
pointer is freed in both _rtl_usb_tx_urb_setup() and _rtl_usb_transmit().
The free belongs _rtl_usb_transmit() instead of _rtl_usb_tx_urb_setup()
and I've cleaned the code up a bit to hopefully make it more clear.
Fixes: 36ef0b473fbf ("rtlwifi: usb: add missing freeing of skbuff") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200513093951.GD347693@mwanda Signed-off-by: Sasha Levin <sashal@kernel.org>
In gsi_channel_start() there is harmless-looking comment "Clear the
channel's event ring interrupt in case it's pending". The intent
was to avoid getting spurious interrupts when first bringing up a
channel.
However we now use channel stop/start to implement suspend and
resume, and an interrupt pending at the time we resume is actually
something we don't want to ignore.
The very first time we bring up the channel we do not expect an
interrupt to be pending, and even if it were, the effect would
simply be to schedule NAPI on that channel, which would find nothing
to do, which is not a problem.
Stop clearing any pending IEOB interrupt in gsi_channel_start().
That leaves one caller of the trivial function gsi_isr_ieob_clear().
Get rid of that function and just open-code it in gsi_isr_ieob()
instead.
This fixes a problem where suspend/resume IPA v4.2 would get stuck
when resuming after a suspend.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 294f2fc6da27 ("bpf: Verifer, adjust_scalar_min_max_vals to always
call update_reg_bounds()") changed the way verifier logs some of its state,
adjust the test_align accordingly. Where possible, I tried to not copy-paste
the entire log line and resorted to dropping the last closing brace instead.
Fixes: 294f2fc6da27 ("bpf: Verifer, adjust_scalar_min_max_vals to always call update_reg_bounds()") Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200515194904.229296-1-sdf@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After enabled loopback packets for IPoIB, we need to drop these packets
that this HCA has replicated and came back to the same interface that
sent them.
Some file descriptors use separate waitqueues for their f_ops->poll()
handler, most commonly one for read and one for write. The io_uring
poll implementation doesn't work with that, as the 2nd poll_wait()
call will cause the io_uring poll request to -EINVAL.
This affects (at least) tty devices and /dev/random as well. This is a
big problem for event loops where some file descriptors work, and others
don't.
With this fix, io_uring handles multiple waitqueues.
When building for ARMv7-M, clang-9 or higher tries to unroll some loops,
which ends up confusing the register allocator to the point of generating
rather bad code and using more than the warning limit for stack frames:
warning: stack frame size of 1200 bytes in function 'blake2b_compress' [-Wframe-larger-than=]
Forcing it to not unroll the final loop avoids this problem.
When native XDP redirect into a veth device, the frame arrives in the
xdp_frame structure. It is then processed in veth_xdp_rcv_one(),
which can run a new XDP bpf_prog on the packet. Doing so requires
converting xdp_frame to xdp_buff, but the tricky part is that
xdp_frame memory area is located in the top (data_hard_start) memory
area that xdp_buff will point into.
The current code tried to protect the xdp_frame area, by assigning
xdp_buff.data_hard_start past this memory. This results in 32 bytes
less headroom to expand into via BPF-helper bpf_xdp_adjust_head().
This protect step is actually not needed, because BPF-helper
bpf_xdp_adjust_head() already reserve this area, and don't allow
BPF-prog to expand into it. Thus, it is safe to point data_hard_start
directly at xdp_frame memory area.
When the QoS targets are met and nothing is being throttled, there's
no way to tell how saturated the underlying device is - it could be
almost entirely idle, at the cusp of saturation or anywhere inbetween.
Given that there's no information, it's best to keep vrate as-is in
this state. Before 7cd806a9a953 ("iocost: improve nr_lagging
handling"), this was the case - if the device isn't missing QoS
targets and nothing is being throttled, busy_level was reset to zero.
While fixing nr_lagging handling, 7cd806a9a953 ("iocost: improve
nr_lagging handling") broke this. Now, while the device is hitting
QoS targets and nothing is being throttled, vrate keeps getting
adjusted according to the existing busy_level.
This led to vrate keeping climing till it hits max when there's an IO
issuer with limited request concurrency if the vrate started low.
vrate starts getting adjusted upwards until the issuer can issue IOs
w/o being throttled. From then on, QoS targets keeps getting met and
nothing on the system needs throttling and vrate keeps getting
increased due to the existing busy_level.
This patch makes the following changes to the busy_level logic.
* Reset busy_level if nr_shortages is zero to avoid the above
scenario.
* Make non-zero nr_lagging block lowering nr_level but still clear
positive busy_level if there's clear non-saturation signal - QoS
targets are met and nr_shortages is non-zero. nr_lagging's role is
preventing adjusting vrate upwards while there are long-running
commands and it shouldn't keep busy_level positive while there's
clear non-saturation signal.
Using GFP_NOIO flag to call scribble_alloc() from resize_chunk() does
not have the expected behavior. kvmalloc_array() inside scribble_alloc()
which receives the GFP_NOIO flag will eventually call kmalloc_node() to
allocate physically continuous pages.
Now we have memalloc scope APIs in mddev_suspend()/mddev_resume() to
prevent memory reclaim I/Os during raid array suspend context, calling
to kvmalloc_array() with GFP_KERNEL flag may avoid deadlock of recursive
I/O as expected.
This patch removes the useless gfp flags from parameters list of
scribble_alloc(), and call kvmalloc_array() with GFP_KERNEL flag. The
incorrect GFP_NOIO flag does not exist anymore.
Fixes: b330e6a49dc3 ("md: convert to kvmalloc") Suggested-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to check mddev->del_work before flush workqueu since the purpose
of flush is to ensure the previous md is disappeared. Otherwise the similar
deadlock appeared if LOCKDEP is enabled, it is due to md_open holds the
bdev->bd_mutex before flush workqueue.
And md_alloc also flushed the same workqueue, but the thing is different
here. Because all the paths call md_alloc don't hold bdev->bd_mutex, and
the flush is necessary to avoid race condition, so leave it as it is.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdfee ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdfee ("brcmfmac: add support for SAE authentication offload") Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Before commit 74b5a5968fe8 ("selftests/bpf: Replace test_progs and
test_maps w/ general rule") selftests/bpf used generic install
target from selftests/lib.mk to install generated bpf test progs
by mentioning them in TEST_GEN_FILES variable.
Take that functionality back.
Fixes: 74b5a5968fe8 ("selftests/bpf: Replace test_progs and test_maps w/ general rule") Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20200513021722.7787-1-yauheni.kaliuta@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
mac80211/hostapd runs mt7615_set_channel with the same channel
parameters sending multiple rdd commands overwriting the previous ones.
This behaviour is causing tpt issues on dfs channels.
Fix the issue checking new channel freq/width with the running one.
Fixes: 5dabdf71e94e ("mt76: mt7615: add multiple wiphy support to the dfs support code") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Normally kdump kernel(s) run under severe memory constraint with the
basic idea being to save the crashdump vmcore reliably when the primary
kernel panics/hangs.
Currently the qed* ethernet driver ends up consuming a lot of memory in
the kdump kernel, leading to kdump kernel panic when one tries to save
the vmcore via ssh/nfs (thus utilizing the services of the underlying
qed* network interfaces).
An example OOM message log seen in the kdump kernel can be seen here
[1], with crashkernel size reservation of 512M.
Using tools like memstrack (see [2]), we can track the modules taking up
the bulk of memory in the kdump kernel and organize the memory usage
output as per 'highest allocator first'. An example log for the OOM case
indicates that the qed* modules end up allocating approximately 216M
memory, which is a large part of the total crashkernel size:
dracut-pre-pivot[676]: ======== Report format module_summary: ========
dracut-pre-pivot[676]: Module qed using 149.6MB (2394 pages), peak allocation 149.6MB (2394 pages)
dracut-pre-pivot[676]: Module qede using 65.3MB (1045 pages), peak allocation 65.3MB (1045 pages)
This patch reduces the default RX and TX ring count from 1024 to 64
when running inside kdump kernel, which leads to a significant memory
saving.
An example log with the patch applied shows the reduced memory
allocation in the kdump kernel:
dracut-pre-pivot[674]: ======== Report format module_summary: ========
dracut-pre-pivot[674]: Module qed using 141.8MB (2268 pages), peak allocation 141.8MB (2268 pages)
<..snip..>
[dracut-pre-pivot[674]: Module qede using 4.8MB (76 pages), peak allocation 4.9MB (78 pages)
Tested crashdump vmcore save via ssh/nfs protocol using underlying qed*
network interface after applying this patch.
Currently when the sending of any management pkt
via wmi command fails, the packet is being unmapped
freed in the error handling. But the idr entry added,
which is used to track these packet is not getting removed.
Hence, during unload, in wmi cleanup, all the entries
in IDR are removed and the corresponding buffer is
attempted to be freed. This can cause a situation where
one packet is attempted to be freed twice.
Fix this error by rmeoving the msdu from the idr
list when the sending of a management packet over
wmi fails.
The qmi infrastructure sends the client a del_server
event when the client releases its qmi handle. This
is not the msg indicating the actual qmi server exiting.
In such cases the del_server msg should not be processed,
since the wifi firmware does not reset its qmi state.
Hence skip the processing of del_server event when the
driver is unloading.
Since commit 147b27e4bd08 ("nvme-pci: allocate device queues storage
space at probe"), nvme_alloc_queue does not alloc the nvme queues
itself anymore.
If the write/poll_queues module parameters are changed at runtime to
values larger than the number of allocated queues in nvme_probe,
nvme_alloc_queue will access unallocated memory.
Add a new nr_allocated_queues member to struct nvme_dev to record how
many queues were alloctated in nvme_probe to avoid using more than the
allocated queues after a reset following a change to the
write/poll_queues module parameters.
Also add nr_write_queues and nr_poll_queues members to allow refreshing
the number of write and poll queues based on a change to the module
parameters when resetting the controller.
Fixes: 147b27e4bd08 ("nvme-pci: allocate device queues storage space at probe") Signed-off-by: Weiping Zhang <zhangweiping@didiglobal.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
[hch: add nvme_max_io_queues, update the commit message] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_ARCH_NO_SG_CHAIN is set, op->sgl[0] cannot be dereferenced,
as gcc-10 now points out:
drivers/nvme/host/fc.c: In function 'nvme_fc_init_request':
drivers/nvme/host/fc.c:1774:29: warning: array subscript 0 is outside the bounds of an interior zero-length array 'struct scatterlist[0]' [-Wzero-length-bounds]
1774 | op->op.fcp_req.first_sgl = &op->sgl[0];
| ^~~~~~~~~~~
drivers/nvme/host/fc.c:98:21: note: while referencing 'sgl'
98 | struct scatterlist sgl[NVME_INLINE_SG_CNT];
| ^~~
I don't know if this is a legitimate warning or a false-positive.
If this is just a false alarm, the warning is easily suppressed
by interpreting the array as a pointer.
Fixes: b1ae1a238900 ("nvme-fc: Avoid preallocating big SGL for data") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a helper to check if we can use Identify CNS values > 1, and refine
the Qemu quirk to not apply to reported versions larger than 1.1, as the
Qemu implementation had been fixed by then.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we set amsdu_len one after another the second one overwrites
the orig_amsdu_len so allow only moving from debug to non debug state.
Also the TLC update check was wrong: it was checking that also the orig
is smaller then the new updated size, which is not the case in debug
amsdu mode.
Commit de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet mode
switch on 2-in-1's") added a DMI chassis-type check to avoid accidentally
reporting SW_TABLET_MODE = 1 to userspace on laptops.
Some devices with a detachable keyboard and using the intel-vbnt (INT33D6)
interface to report if they are in tablet mode (keyboard detached) or not,
report 32 / "Detachable" as chassis-type, e.g. the HP Pavilion X2 series.
Other devices with a detachable keyboard and using the intel-vbnt (INT33D6)
interface to report SW_TABLET_MODE, report 8 / "Portable" as chassis-type.
The Dell Venue 11 Pro 7130 is an example of this.
Extend the DMI chassis-type check to also accept Portables and Detachables
so that the intel-vbtn driver will report SW_TABLET_MODE on these devices.
Note the chassis-type check was originally added to avoid a false-positive
tablet-mode report on the Dell XPS 9360 laptop. To the best of my knowledge
that laptop is using a chassis-type of 9 / "Laptop", so after this commit
we still ignore the tablet-switch for that chassis-type.
Fixes: de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet mode switch on 2-in-1's") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Mario Limonciello <Mario.limonciello@dell.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet mode
switch on 2-in-1's") added a DMI chassis-type check to avoid accidentally
reporting SW_TABLET_MODE = 1 to userspace on laptops (specifically on the
Dell XPS 9360), to avoid e.g. userspace ignoring touchpad events because
userspace thought the device was in tablet-mode.
But if we are not getting the initial status of the switch because the
device does not have a tablet mode, then we really should not advertise
the presence of a tablet-mode switch to userspace at all, as userspace may
use the mere presence of this switch for certain heuristics.
Fixes: de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet mode switch on 2-in-1's") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Split the sparse keymap into 2 separate keymaps, a buttons and a switches
keymap and combine the 2 to a single map again in intel_vbtn_input_setup().
This is a preparation patch for not telling userspace that we have switches
when we do not have them (and for doing the same for the buttons).
Fixes: de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet mode switch on 2-in-1's") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use acpi_evaluate_integer() instead of open-coding it.
This is a preparation patch for adding a intel_vbtn_has_switches()
helper function.
Fixes: de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet mode switch on 2-in-1's") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pre-flush dquot verification in xfs_qm_dqflush() duplicates the
read verifier by checking the dquot in the on-disk buffer. Instead,
verify the in-core variant before it is flushed to the buffer.
Fixes: 7224fa482a6d ("xfs: add full xfs_dqblk verifier") Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Allison Collins <allison.henderson@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The buffer write failure flag is intended to control the internal
write retry that XFS has historically implemented to help mitigate
the severity of transient I/O errors. The flag is set when a buffer
is resubmitted from the I/O completion path due to a previous
failure. It is checked on subsequent I/O completions to skip the
internal retry and fall through to the higher level configurable
error handling mechanism. The flag is cleared in the synchronous and
delwri submission paths and also checked in various places to log
write failure messages.
There are a couple minor problems with the current usage of this
flag. One is that we issue an internal retry after every submission
from xfsaild due to how delwri submission clears the flag. This
results in double the expected or configured number of write
attempts when under sustained failures. Another more subtle issue is
that the flag is never cleared on successful I/O completion. This
can cause xfs_wait_buftarg() to suggest that dirty buffers are being
thrown away due to the existence of the flag, when the reality is
that the flag might still be set because the write succeeded on the
retry.
Clear the write failure flag on successful I/O completion to address
both of these problems. This means that the internal retry attempt
occurs once since the last time a buffer write failed and that
various other contexts only see the flag set when the immediately
previous write attempt has failed.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Allison Collins <allison.henderson@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently there is a small window where a badly timed migration could
cause in_dbg_master() to spuriously return true. Specifically if we
migrate to a new core after reading the processor id and the previous
core takes a breakpoint then we will evaluate true if we read
kgdb_active before we get the IPI to bring us to halt.
Fix this by checking irqs_disabled() first. Interrupts are always
disabled when we are executing the kgdb trap so this is an acceptable
prerequisite. This also allows us to replace raw_smp_processor_id()
with smp_processor_id() since the short circuit logic will prevent
warnings from PREEMPT_DEBUG.
Fixes: dcc7871128e9 ("kgdb: core changes to support kdb") Suggested-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20200506164223.2875760-1-daniel.thompson@linaro.org Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache
errors") adds cm2_causes[] array with map of error type ID and
pointers to the short description string. There is a mistake in
the table, since according to MIPS32 manual CM2_ERROR_TYPE = {17,18}
correspond to INTVN_WR_ERR and INTVN_RD_ERR, while the table
claims they have {0x17,0x18} codes. This is obviously hex-dec
copy-paste bug. Moreover codes {0x18 - 0x1a} indicate L2 ECC errors.
Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors") Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-pm@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
LLD failed to link vmlinux with 64bit load address for 32bit ELF
while bfd will strip 64bit address into 32bit silently.
To fix LLD build, we should truncate load address provided by platform
into 32bit for 32bit kernel.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Link: https://github.com/ClangBuiltLinux/linux/issues/786 Link: https://sourceware.org/bugzilla/show_bug.cgi?id=25784 Reviewed-by: Fangrui Song <maskray@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Cc: Maciej W. Rozycki <macro@linux-mips.org> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The addition of sja1105_port_status_ether structure into the
statistics causes the frame size to go over the warning limit:
drivers/net/dsa/sja1105/sja1105_ethtool.c:421:6: error: stack frame size of 1104 bytes in function 'sja1105_get_ethtool_stats' [-Werror,-Wframe-larger-than=]
Use dynamic allocation to avoid this.
Fixes: 336aa67bd027 ("net: dsa: sja1105: show more ethtool statistics counters for P/Q/R/S") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ccm(aes) test fails when req->assoclen > ~240bytes.
The problem is the value assigned to auth_offset is wrong.
As auth_offset is unsigned char, it can take max value as 255.
So fix it by making it unsigned int.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com> Signed-off-by: Devulapally Shiva Krishna <shiva@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This solves the following issues observed during self test when
CONFIG_CRYPTO_MANAGER_EXTRA_TESTS is enabled.
1. Added fallback for cbc, ctr and rfc3686 if req->nbytes is zero
and for xts added a fallback case if req->nbytes is not multiple of 16.
2. In case of cbc-aes, solved wrong iv update. When
chcr_cipher_fallback() is called, used req->info pointer instead of
reqctx->iv.
3. In cbc-aes decryption there was a wrong result. This occurs when
chcr_cipher_fallback() is called from chcr_handle_cipher_resp().
In the fallback function iv(req->info) used is wrongly updated.
So use the initial iv for this case.
4)In case of ctr-aes encryption observed wrong result. In adjust_ctr_overflow()
there is condition which checks if ((bytes / AES_BLOCK_SIZE) > c),
where c is the number of blocks which can be processed without iv overflow,
but for the above bytes (req->nbytes < 32 , not a multiple of 16) this
condition fails and the 2nd block is corrupted as it requires the rollover iv.
So added a '=' condition in this to take care of this.
5)In rfc3686-ctr there was wrong result observed. This occurs when
chcr_cipher_fallback() is called from chcr_handle_cipher_resp().
Here also copying initial_iv in init_iv pointer for handling the fallback
case correctly.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com> Signed-off-by: Devulapally Shiva Krishna <shiva@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently there is a check if priv is null when calling lbtf_remove_card
but not in a previous call to if_usb_reset_dev that can also dereference
priv. Fix this by also only calling lbtf_remove_card if priv is null.
It is noteable that there don't seem to be any bugs reported that the
null pointer dereference has ever occurred, so I'm not sure if the null
check is required, but since we're doing a null check anyway it should
be done for both function calls.
Addresses-Coverity: ("Dereference before null check") Fixes: baa0280f08c7 ("libertas_tf: don't defer firmware loading until start()") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200501173900.296658-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we may perform a copy_to_user (through
simple_read_from_buffer()) while holding a context's register_lock,
while accessing the context save area.
This change uses a temporary buffer for the context save area data,
which we then pass to simple_read_from_buffer.
Includes changes from Christoph Hellwig <hch@lst.de>.
Fixes: bf1ab978be23 ("[POWERPC] coredump: Add SPU elf notes to coredump.") Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
[hch: renamed to function to avoid ___-prefixes] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type. And emac_start_xmit() can
leak one skb if 'channel' == 3.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The log_addrs->log_addr_type[i] value is a u8 which is controlled by
the user and comes from the ioctl. If it's over 31 then that results in
undefined behavior (shift wrapping) and that leads to a Smatch static
checker warning. We already cap the value later so we can silence the
warning just by re-ordering the existing checks.
I think the UBSan checker will also catch this bug at runtime and
generate a warning. But otherwise the bug is harmless.
'cmd' is malloced in ath10k_bmi_lz_data_large() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: d58f466a5dee ("ath10k: add large size for BMI download data for SDIO") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200427104348.13570-1-weiyongjun1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
since devm_ioremap() does not check input parameters for null.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 03f66f067560 ("net: ethernet: ti: davinci_mdio: use devm_ioremap()") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log