In case that icdoff is not zero or mandatory keyed sgls are not
supported by the NVMe/RDMA target, we'll go to error flow but we'll
return 0 to the caller. Fix it by returning an appropriate error code.
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs") Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Acked-by: Pali Rohár <pali@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl Signed-off-by: Sasha Levin <sashal@kernel.org>
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
A new warning in clang points out a use of bitwise OR with boolean
expressions in this driver:
drivers/platform/x86/thinkpad_acpi.c:9061:11: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
else if ((strlencmp(cmd, "level disengaged") == 0) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/platform/x86/thinkpad_acpi.c:9061:11: note: cast one or both operands to int to silence this warning
1 error generated.
This should clearly be a logical OR so change it to fix the warning.
Fixes: fe98a52ce754 ("ACPI: thinkpad-acpi: add sysfs support to fan subdriver") Link: https://github.com/ClangBuiltLinux/linux/issues/1476 Reported-by: Tor Vic <torvic9@mailbox.org> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211018182537.2316800-1-nathan@kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sk_stream_kill_queues() can be called on close when there are
still outstanding skbs to transmit. Those skbs may try to queue
notifications to the error queue (e.g. timestamps).
If sk_stream_kill_queues() purges the queue without taking
its lock the queue may get corrupted, and skbs leaked.
This shows up as a warning about an rmem leak:
WARNING: CPU: 24 PID: 0 at net/ipv4/af_inet.c:154 inet_sock_destruct+0x...
The leak is always a multiple of 0x300 bytes (the value is in
%rax on my builds, so RAX: 0000000000000300). 0x300 is truesize of
an empty sk_buff. Indeed if we dump the socket state at the time
of the warning the sk_error_queue is often (but not always)
corrupted. The ->next pointer points back at the list head,
but not the ->prev pointer. Indeed we can find the leaked skb
by scanning the kernel memory for something that looks like
an skb with ->sk = socket in question, and ->truesize = 0x300.
The contents of ->cb[] of the skb confirms the suspicion that
it is indeed a timestamp notification (as generated in
__skb_complete_tx_timestamp()).
Removing purging of sk_error_queue should be okay, since
inet_sock_destruct() does it again once all socket refs
are gone. Eric suggests this may cause sockets that go
thru disconnect() to maintain notifications from the
previous incarnations of the socket, but that should be
okay since the race was there anyway, and disconnect()
is not exactly dependable.
Thanks to Jonathan Lemon and Omar Sandoval for help at various
stages of tracing the issue.
Fixes: cb9eff097831 ("net: new user space API for time stamping of incoming and outgoing packets") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The msm_gem_new_impl() function cleans up after itself so there is no
need to call drm_gem_object_put(). Conceptually, it does not make sense
to call a kref_put() function until after the reference counting has
been initialized which happens immediately after this call in the
drm_gem_(private_)object_init() functions.
In the msm_gem_import() function the "obj" pointer is uninitialized, so
it will lead to a crash.
Fixes: 05b849111c07 ("drm/msm: prime support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211013081315.GG6010@kili Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9b8 ("ath10k: use proper tx power unit") Signed-off-by: Sven Eckelmann <seckelmann@datto.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When device_register() returns an error, the name allocated in
dev_set_name() will be leaked, the put_device() should be used
instead of calling hwmon_dev_release() to give up the device
reference, then the name will be freed in kobject_cleanup().
The "msh" pointer is device managed, meaning that memstick_alloc_host()
calls device_initialize() on it. That means that it can't be free
using kfree() but must instead be freed with memstick_free_host().
Otherwise it leads to a tiny memory leak of device resources.
Fixes: 60fdd931d577 ("memstick: add support for JMicron jmb38x MemoryStick host controller") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211011123912.GD15188@kili Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-14 complains about a sanity check that always passes when the
page size is 64KB or larger:
drivers/memstick/core/ms_block.c:1739:21: error: result of comparison of constant 65536 with expression of type 'unsigned short' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (msb->page_size > PAGE_SIZE) {
~~~~~~~~~~~~~~ ^ ~~~~~~~~~
This is fine, it will still work on all architectures, so just shut
up that warning with a cast.
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: ef1a628d83fc ("b43: Implement dynamic PHY API") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Büsch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211006073621.GE8404@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: 75388acd0cd8 ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Büsch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211006073542.GD8404@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently mtk_rng_runtime_suspend/resume is called for both runtime pm
and system sleep operations.
This is wrong as these should only be runtime ops as the name already
suggests. Currently freezing the system will lead to a call to
mtk_rng_runtime_suspend even if the device currently isn't active. This
leads to a clock warning because it is disabled/unprepared although it
isn't enabled/prepared currently.
This patch fixes this by only setting the runtime pm ops and forces to
call the runtime pm ops from the system sleep ops as well if active but
not otherwise.
Upon receiving a PFVF message, check if the interrupt bit is set in the
message. If it is not, that means that the interrupt was probably
triggered by a collision. In this case, disregard the message and
re-enable the interrupts.
Fixes: ed8ccaef52fa ("crypto: qat - Add support for SRIOV") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Detect a PFVF collision between the local and the remote function by
checking if the message on the PFVF CSR has been overwritten.
This is done after the remote function confirms that the message has
been received, by clearing the interrupt bit, or the maximum number of
attempts (ADF_IOV_MSG_ACK_MAX_RETRY) to check the CSR has been exceeded.
Fixes: ed8ccaef52fa ("crypto: qat - Add support for SRIOV") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Co-developed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
mn88443x_cmn_power_on() did not handle possible errors of
clk_prepare_enable() and always finished successfully so that its caller
mn88443x_probe() did not care about failed preparing/enabling of clocks
as well.
Add missed error handling in both mn88443x_cmn_power_on() and
mn88443x_probe(). This required to change the return value of the former
from "void" to "int".
Found by Linux Driver Verification project (linuxtesting.org).
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt
19.07 we could force a silent restart of a device with no serial
output when we were sending a high amount of UDP traffic (iperf3 at 80
MBit/s in both directions from external hosts, saturating the wifi and
causing a load of about 4.5 to 6) and were then triggering an
ath9k_queue_reset().
Further debugging showed that the restart was caused by the ath79
watchdog. With disabled watchdog we could observe that the device was
constantly going into ath_isr() interrupt handler and was returning
early after the ATH_OP_HW_RESET flag test, without clearing any
interrupts. Even though ath9k_queue_reset() calls
ath9k_hw_kill_interrupts().
With JTAG we could observe the following race condition:
So the ath9k_tasklet() reenables the ath9k interrupts
through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just
disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED
without actually clearing the interrupt.
To fix this IRQ storm also clear/disable the interrupts again when we
are in reset state.
Cc: Sven Eckelmann <sven@narfation.org> Cc: Simon Wunderlich <sw@simonwunderlich.de> Cc: Linus Lüssing <linus.luessing@c0d3.blue> Fixes: 872b5d814f99 ("ath9k: do not access hardware on IRQs during reset") Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to ops->suspend for the dev->dev_next case can currently
trigger a call on a null function pointer if ops->suspend is null.
Skip over the use of function ops->suspend if it is null.
Addresses-Coverity: ("Dereference after null check")
Fixes: be7fd3c3a8c5 ("media: em28xx: Hauppauge DualHD second tuner functionality") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit c343bf1ba5ef ("cpuidle: Fix three reference count leaks")
fixes the cleanup of kobjects; however, it removes kfree() calls
altogether, leading to memory leaks.
Fix those and also defer the initialization of dev->kobj_dev until
after the error check, so that we do not end up with a dangling
pointer.
Fixes: c343bf1ba5ef ("cpuidle: Fix three reference count leaks") Signed-off-by: Anel Orazgaliyeva <anelkz@amazon.de> Suggested-by: Aman Priyadarshi <apeureka@amazon.de>
[ rjw: Subject edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently a call to snd_card_new that fails will set card with a NULL
pointer, this causes a null pointer dereference on the error cleanup
path when card it passed to snd_card_free. Fix this by adding a new
error exit path that does not call snd_card_free and exiting via this
new path.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 9e44d63246a9 ("[media] cx23885: Add ALSA support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "card" string only holds 31 characters (and the terminating NUL).
In order to avoid truncation, use a shorter card description instead of
the current result, "Silicon Labs Si470x FM Radio Re".
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 78656acdcf48 ("V4L/DVB (7038): USB radio driver for Silicon Labs Si470x FM Radio Receivers") Fixes: cc35bbddfe10 ("V4L/DVB (12416): radio-si470x: add i2c driver for si470x") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
Syzbot reported ununit-value bug in az6027_rc_query(). The problem was
in missing state pointer initialization. Since this function does nothing
we can simply initialize state to REMOTE_NO_KEY_PRESSED.
Reported-and-tested-by: syzbot+2cd8c5db4a85f0a04142@syzkaller.appspotmail.com Fixes: 76f9a820c867 ("V4L/DVB: AZ6027: Initial import of the driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If em28xx dev has ->dev_next pointer, we need to delete ->dev_next list
node from em28xx_extension_devlist on disconnect to avoid UAF bugs and
corrupted list bugs, since driver frees this pointer on disconnect.
Reported-and-tested-by: syzbot+a6969ef522a36d3344c9@syzkaller.appspotmail.com Fixes: 1a23f81b7dc3 ("V4L/DVB (9979): em28xx: move usb probe code to a proper place") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The overflow check in amdgpu_bo_list_create() causes a warning with
clang-14 on 64-bit architectures, since the limit can never be
exceeded.
drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c:74:18: error: result of comparison of constant 256204778801521549 with expression of type 'unsigned int' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (num_entries > (SIZE_MAX - sizeof(struct amdgpu_bo_list))
~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The check remains useful for 32-bit architectures, so just avoid the
warning by using size_t as the type for the count.
Fixes: 920990cb080a ("drm/amdgpu: allocate the bo_list array after the list") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Cc: Mauri Sandberg <sandberg@mailfence.com> Cc: DENG Qingfang <dqfext@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was caused by the fact that rebind_subsystem() disables
controllers to be rebound one by one. If more than one disabled
controllers are originally from the default hierarchy, it means that
cgroup_apply_control_disable() will be called multiple times for the
same default hierarchy. A controller may be killed by css_kill() in
the first round. In the second round, the killed controller may not be
completely dead yet leading to the warning.
To avoid this problem, we collect all the ssid's of controllers that
needed to be disabled from the default hierarchy and then disable them
in one go instead of one by one.
Fixes: 334c3679ec4b ("cgroup: reimplement rebind_subsystems() using cgroup_apply_control() and friends") Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before freeing struct sco_conn, all delayed timeout work should be
cancelled. Otherwise, sco_sock_timeout could potentially use the
sco_conn after it has been freed.
Additionally, sco_conn.timeout_work should be initialized when the
connection is allocated, not when the channel is added. This is
because an sco_conn can create channels with multiple sockets over its
lifetime, which happens if sockets are released but the connection
isn't deleted.
Fixes: ba316be1b6a0 ("Bluetooth: schedule SCO timeouts with delayed_work") Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With idle polling, IPIs are not sent when a CPU idle, but queued
and run later from do_idle(). The default kgdb_call_nmi_hook()
implementation gets the pointer to struct pt_regs from get_irq_reqs(),
which doesn't work in that case because it was not called from the
IPI interrupt handler. Fix it by defining our own kgdb_roundup()
function which sents an IPI_ENTER_KGDB. When that IPI is received
on the target CPU kgdb_nmicallback() is called.
With 64 bit kernels unwind_special() is not working because
it compares the pc to the address of the function descriptor.
Add a helper function that compares pc with the dereferenced
address. This fixes all of the backtraces on my c8000. Without
this changes, a lot of backtraces are missing in kdb or the
show-all-tasks command from /proc/sysrq-trigger.
The function end_of_stack() returns a pointer to the last entry of a
stack. For architectures like parisc where the stack grows upwards
return the pointer to the highest address in the stack.
Without this change I faced a crash on parisc, because the stackleak
functionality wrote STACKLEAK_POISON to the lowest address and thus
overwrote the first 4 bytes of the task_struct which included the
TIF_FLAGS.
The following issue is observed with CONFIG_DEBUG_PREEMPT when KVM loads:
KVM: vmx: using Hyper-V Enlightened VMCS
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/488
caller is set_hv_tscchange_cb+0x16/0x80
CPU: 1 PID: 488 Comm: systemd-udevd Not tainted 5.15.0-rc5+ #396
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.0 12/17/2019
Call Trace:
dump_stack_lvl+0x6a/0x9a
check_preemption_disabled+0xde/0xe0
? kvm_gen_update_masterclock+0xd0/0xd0 [kvm]
set_hv_tscchange_cb+0x16/0x80
kvm_arch_init+0x23f/0x290 [kvm]
kvm_init+0x30/0x310 [kvm]
vmx_init+0xaf/0x134 [kvm_intel]
...
set_hv_tscchange_cb() can get preempted in between acquiring
smp_processor_id() and writing to HV_X64_MSR_REENLIGHTENMENT_CONTROL. This
is not an issue by itself: HV_X64_MSR_REENLIGHTENMENT_CONTROL is a
partition-wide MSR and it doesn't matter which particular CPU will be
used to receive reenlightenment notifications. The only real problem can
(in theory) be observed if the CPU whose id was acquired with
smp_processor_id() goes offline before we manage to write to the MSR,
the logic in hv_cpu_die() won't be able to reassign it correctly.
When configuring the kernel for big-endian, we set either BE-8 or BE-32
based on the CPU architecture level. Until linux-4.4, we did not have
any ARMv7-M platform allowing big-endian builds, but now i.MX/Vybrid
is in that category, adn we get a build error because of this:
arch/arm/kernel/module-plts.c: In function 'get_module_plt':
arch/arm/kernel/module-plts.c:60:46: error: implicit declaration of function '__opcode_to_mem_thumb32' [-Werror=implicit-function-declaration]
This comes down to picking the wrong default, ARMv7-M uses BE8
like ARMv7-A does. Changing the default gets the kernel to compile
and presumably works.
When addr_gen_mode is set to IN6_ADDR_GEN_MODE_NONE, the link-local addr
should not be generated. But it isn't the case for GRE (as well as GRE6)
and SIT tunnels. Make it so that tunnels consider the addr_gen_mode,
especially for IN6_ADDR_GEN_MODE_NONE.
Do this in add_v4_addrs() to cover both GRE and SIT only if the addr
scope is link.
Currently the stacktrace on clang compiled arm kernel uses the 'lr'
register to find the first frame address from pt_regs. However, that
is wrong after calling another function, because the 'lr' register
is used by 'bl' instruction and never be recovered.
As same as gcc arm kernel, directly use the frame pointer (r11) of
the pt_regs to find the first frame address.
Note that this fixes kretprobe stacktrace issue only with
CONFIG_UNWINDER_FRAME_POINTER=y. For the CONFIG_UNWINDER_ARM,
we need another fix.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting kernel panic at smk_cipso_doi() due to memory
allocation fault injection [1]. The reason for need to use panic() was
not explained. But since no fix was proposed for 18 months, for now
let's use __GFP_NOFAIL for utilizing syzbot resource on other bugs.
Just like we have default SMPS mode as dynamic in powersave,
we should not enable RX-diversity in powersave, to reduce
power consumption when connected to a non-MIMO AP.
That happens because swsusp_check() calls set_blocksize() on the
target partition which confuses the file system:
Thread1 Thread2
mount /dev/sda /home/test
get s_mmp_bh --> has mapped flag
start kmmpd thread
echo "/dev/sda" > /sys/power/resume
resume_store
software_resume
swsusp_check
set_blocksize
truncate_inode_pages_range
truncate_cleanup_page
block_invalidatepage
discard_buffer --> clean mapped flag
write_mmp_block
submit_bh
submit_bh_wbc
BUG_ON(!buffer_mapped(bh))
To address this issue, modify swsusp_check() to open the target block
device with exclusive access.
Signed-off-by: Ye Bin <yebin10@huawei.com>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the driver fails to request the firmware, it calls its error
handler. In the error handler, the driver detaches device from driver
first before releasing the firmware, which can cause a use-after-free bug.
If CONFIG_CFI_CLANG=y, attempting to read an event histogram will cause
the kernel to panic due to failed CFI check.
1. echo 'hist:keys=common_pid' >> events/sched/sched_switch/trigger
2. cat events/sched/sched_switch/hist
3. kernel panics on attempting to read hist
This happens because the sort() function expects a generic
int (*)(const void *, const void *) pointer for the compare function.
To prevent this CFI failure, change tracing map cmp_entries_* function
signatures to match this.
Also, fix the build error reported by the kernel test robot [1].
Some unfriendly component, such as dpdk, write the same mask to
unbound kworker cpumask again and again. Every time it write to
this interface some work is queue to cpu, even though the mask
is same with the original mask.
So, fix it by return success and do nothing if the cpumask is
equal with the old one.
This might matter, for example, if the underlying type of enum xz_check
was a signed char. In such a case the validation wouldn't have caught an
unsupported header. I don't know if this problem can occur in the kernel
on any arch but it's still good to fix it because some people might copy
the XZ code to their own projects from Linux instead of the upstream
XZ Embedded repository.
This change may increase the code size by a few bytes. An alternative
would have been to use an unsigned int instead of enum xz_check but
using an enumeration looks cleaner.
With valid files, the safety margin described in lib/decompress_unxz.c
ensures that these buffers cannot overlap. But if the uncompressed size
of the input is larger than the caller thought, which is possible when
the input file is invalid/corrupt, the buffers can overlap. Obviously
the result will then be garbage (and usually the decoder will return
an error too) but no other harm will happen when such an over-run occurs.
This change only affects uncompressed LZMA2 chunks and so this
should have no effect on performance.
For files that lack trailing newlines and match a leaking address (e.g.
wchan[1]), the leaking_addresses.pl report would run together with the
next line, making things look corrupted.
Unconditionally remove the newline on input, and write it back out on
output.
Some buggy firmware and/or brand new batteries can support a charge that's
slightly over the reported design capacity. In such cases, the kernel will
report to userspace that the charging state of the battery is "Unknown",
when in reality the battery charge is "Full", at least from the design
capacity point of view. Make the fallback condition accepts capacities
over the designed capacity so userspace knows that is full.
Signed-off-by: André Almeida <andrealmeid@collabora.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
The tracefs file system is by default mounted such that only root user can
access it. But there are legitimate reasons to create a group and allow
those added to the group to have access to tracing. By changing the
permissions of the tracefs mount point to allow access, it will allow
group access to the tracefs directory.
There should not be any real reason to allow all access to the tracefs
directory as it contains sensitive information. Have the default
permission of directories being created not have any OTH (other) bits set,
such that an admin that wants to give permission to a group has to first
disable all OTH bits in the file system.
In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets
assigned an value that's not properly initialized.
Using kzalloc() in place of kmalloc() for the buffer fixes this issue,
as the val can now be set to 0 in the event dibusb_i2c_msg() fails.
During wakeup from system-wide sleep states, acpi_get_sleep_type_data()
is called and it tries to get memory from the slab allocator in order
to evaluate a control method, but if KFENCE is enabled in the kernel,
the memory allocation attempt causes an IRQ work to be queued and a
self-IPI to be sent to the CPU running the code which requires the
memory controller to be ready, so if that happens too early in the
wakeup path, it doesn't work.
Prevent that from taking place by calling acpi_get_sleep_type_data()
for S0 upfront, when preparing to enter a given sleep state, and
saving the data obtained by it for later use during system wakeup.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271 Reported-by: Reik Keutterling <spielkind@gmail.com> Tested-by: Reik Keutterling <spielkind@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls
_printk(), but _printk() is a static inline function, not available
as an extern.
Since the purpose of the macro is to print the BUGCHECK info,
make this config option depend on PRINTK.
Fixes multiple occurrences of this build error:
../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration
208 | int _printk(const char *s, ...)
| ^~~~~~~
In file included from ../arch/ia64/include/asm/cmpxchg.h:5,
../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)'
146 | extern int _printk(const char *fmt, ...);
Cc: linux-ia64@vger.kernel.org Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Chris Down <chris@chrisdown.name> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzkaller reported a warning called "rcu detected stall in dummy_timer".
The error seems to be an error in mceusb_dev_recv(). In the case of
-EPROTO error, the routine immediately resubmits the URB. Instead it
should return without resubmitting URB.
Reported-by: syzbot+4d3749e9612c2cfab956@syzkaller.appspotmail.com Signed-off-by: Rajat Asthana <rajatasthana4@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
if (!dev->plat_dev)
This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
dev_err(&pdev->dev, "No platform data specified\n");
However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().
To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device is doing something unexpected with the control. Either because
the protocol is not properly implemented or there has been a HW error.
Fixes v4l2-compliance:
Control ioctls (Input 0):
fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22)
test VIDIOC_G/S_CTRL: FAIL
fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
The interrupt handling should be related to the firmware version. If
the driver matches an old firmware, then the driver should not handle
interrupt such as i2c or dma, otherwise it will cause some errors.
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
It turns out that a single page of stack is trivial to overflow with
all the tracing gunk enabled. Raise the exception stacks to 2 pages,
which is still half the interrupt stacks, which are at 4 pages.
Syzkaller reported use-after-free bug as described in [1]. The bug is
triggered when smk_set_cipso() tries to free stale category bitmaps
while there are concurrent reader(s) using the same bitmaps.
Wait for RCU grace period to finish before freeing the category bitmaps
in smk_set_cipso(). This makes sure that there are no more readers using
the stale bitmaps and freeing them should be safe.
mq / mqprio make the default child qdiscs visible. They only do
so for the qdiscs which are within real_num_tx_queues when the
device is registered. Depending on order of calls in the driver,
or if user space changes config via ethtool -L the number of
qdiscs visible under tc qdisc show will differ from the number
of queues. This is confusing to users and potentially to system
configuration scripts which try to make sure qdiscs have the
right parameters.
Add a new Qdisc_ops callback and make relevant qdiscs TTRT.
Note that this uncovers the "shortcut" created by
commit 1f27cde313d7 ("net: sched: use pfifo_fast for non real queues")
The default child qdiscs beyond initial real_num_tx are always
pfifo_fast, no matter what the sysfs setting is. Fixing this
gets a little tricky because we'd need to keep a reference
on whatever the default qdisc was at the time of creation.
In practice this is likely an non-issue the qdiscs likely have
to be configured to non-default settings, so whatever user space
is doing such configuration can replace the pfifos... now that
it will see them.
Reported-by: Matthew Massey <matthewmassey@fb.com> Reviewed-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.
We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, `__query_block()` would fail if the
second WCxx method call failed. However, the
WQxx method might have succeeded, and potentially
allocated memory for the result. Instead of
throwing away the result and potentially
leaking memory, ignore the result of
the second WCxx call.
Once l2cap_sock_teardown_cb() excuted, this sock will be marked as SOCK_ZAPPED,
and can be treated as killable in l2cap_sock_kill() if sock_orphan() has
excuted, at this time we close sock through sock_close() which end to call
l2cap_sock_kill() like Thread C:
Context: Thread C:
sock_close()
l2cap_sock_release()
sock_orphan()
l2cap_sock_kill() #free sock if refcnt is 1
If C completed, Once A or B reaches l2cap_sock_teardown_cb() again,
use-after-free happened.
We should set chan->data to NULL if sock is destructed, for telling teardown
operation is not allowed in l2cap_sock_teardown_cb(), and also we should
avoid killing an already killed socket in l2cap_sock_close_cb().
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sco_send_frame() also takes lock_sock() during memcpy_from_msg()
call that may be endlessly blocked by a task with userfaultd
technique, and this will result in a hung task watchdog trigger.
Just like the similar fix for hci_sock_sendmsg() in commit 92c685dc5de0 ("Bluetooth: reorganize functions..."), this patch moves
the memcpy_from_msg() out of lock_sock() for addressing the hang.
This should be the last piece for fixing CVE-2021-3640 after a few
already queued fixes.
If keyspan_port_probe() fails to allocate memory for an out_buffer[i] or
in_buffer[i], the previously allocated memory for out_buffer or
in_buffer needs to be freed on the error handling path, otherwise a
memory leak will result.
Fixes: bad41a5bf177 ("USB: keyspan: fix port DMA-buffer allocations") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Link: https://lore.kernel.org/r/20211015085543.1203011-1-wanghai38@huawei.com Cc: stable@vger.kernel.org # 3.12 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On success i2c_master_send() returns the number of bytes written. The
call from iio_write_channel_info(), however, expects the return value to
be zero on success.
This bug causes incorrect consumption of the sysfs buffer in
iio_write_channel_info(). When writing more than two characters to
out_voltage0_raw, the ad5446 write handler is called multiple times
causing unexpected behavior.
Fixes: 3ec36a2cf0d5 ("iio:ad5446: Add support for I2C based DACs") Signed-off-by: Pekka Korpinen <pekka.korpinen@iki.fi> Link: https://lore.kernel.org/r/20210929185755.2384-1-pekka.korpinen@iki.fi Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the error path in free_dqentry(), pass out the error number if the
block to free is not correct.
Fixes: 1ccd14b9c271 ("quota: Split off quota tree handling into a separate file") Link: https://lore.kernel.org/r/20211008093821.1001186-3-yi.zhang@huawei.com Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Cc: stable@kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The block number in the quota tree on disk should be smaller than the
v2_disk_dqinfo.dqi_blocks. If the quota file was corrupted, we may be
allocating an 'allocated' block and that would lead to a loop in a tree,
which will probably trigger oops later. This patch adds a check for the
block number in the quota tree to prevent such potential issue.
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b6837
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org Fixes: f21a8b1b6837 ("PCI: aardvark: Move to MSI handling using generic MSI support") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are lot of undocumented interrupt bits. To prevent unwanted
spurious interrupts, fix all *_ALL_MASK macros to define all interrupt
bits, so that driver can properly mask all interrupts, including those
which are undocumented.
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org> Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 411cef6adfb3 ("ALSA: mixer: oss: Fix racy access to slots")
added mutex protection in snd_mixer_oss_set_volume(). Second
mutex_lock() in same function looks like typo, fix it.
The OSS mixer can reassign the mapping slots dynamically via proc
file. Although the addition and deletion of those slots are protected
by mixer->reg_mutex, the access to slots aren't, hence this may cause
UAF when the slots in use are deleted concurrently.
This patch applies the mixer->reg_mutex in all appropriate code paths
(i.e. the ioctl functions) that may access slots.
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc54968 ("[PATCH] tty: switch to ktermios and new framework") Cc: stable@vger.kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the field described in mpc85xx_smp_guts_ids[] is not configured in
dtb, the mpc85xx_setup_pmc() does not assign a value to the "guts"
variable. As a result, the oops is triggered when
mpc85xx_freeze_time_base() is executed.
Fixes: 56f1ba280719 ("powerpc/mpc85xx: refactor the PM operations") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210929033646.39630-2-nixiaoming@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b154 ("power_supply: Add MAX17042 Fuel Gauge Driver") Cc: <stable@vger.kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de> Signed-off-by: Henrik Grimler <henrik@grimler.se> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
max17042_set_soc_threshold gets called with offset set to 1, which means
that minimum threshold value would underflow once SOC got down to 0,
causing invalid alerts from the gauge.
Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC") Cc: <stable@vger.kernel.org> Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT. This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2]. This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.
Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.
As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Maciej Rozycki <macro@orcam.me.uk> Cc: linux-mips@vger.kernel.org
[1] 35938a00ba86 ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout") Cc: stable@vger.kernel.org Fixes: f92722dc4545 ("MIPS: Correct MIPS I FP sigcontext layout") Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
The module parameters are missing dev_oper_mode 12, BT classic alone,
add it. Moreover, the parameters encode newlines, which ends up being
printed malformed e.g. by modinfo, so fix that too.
However, the module parameter string is duplicated in both USB and SDIO
modules and the dev_oper_mode mode enumeration in those module parameters
is a duplicate of macros used by the driver. Furthermore, the enumeration
is confusing.
So, deduplicate the module parameter string and use __stringify() to
encode the correct mode enumeration values into the module parameter
string. Finally, replace 'Wi-Fi' with 'Wi-Fi alone' and 'BT' with
'BT classic alone' to clarify what those modes really mean.
Fixes: 898b255339310 ("rsi: add module parameter operating mode") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com> Cc: Angus Ainslie <angus@akkea.ca> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Karun Eagalapati <karun256@gmail.com> Cc: Martin Fuzzey <martin.fuzzey@flowbird.group> Cc: Martin Kepplinger <martink@posteo.de> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Cc: Siva Rebbagondla <siva8118@gmail.com> Cc: netdev@vger.kernel.org Cc: <stable@vger.kernel.org> # 4.17+ Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916144245.10181-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b56 ("rsi: fix AP mode with WPA failure due to encrypted EAPOL") Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log