tracing expects to see invalid syscalls, so pass it through.
The syscall path in entry.S checks the syscall number before
looking up the handler, so it is still safe.
Use noirq suspend/resume callbacks as other drivers which implement
noirq suspend/resume callbacks (Ex:- PCIe) depend on pinctrl driver to
configure the signals used by their respective devices in the noirq phase.
Fix the following warnings caused by reusage of the same irq_chip
instance for all spmi-gpio gpio_irq_chip instances. Instead embed
irq_chip into pmic_gpio_state struct.
gpio gpiochip2: (c440000.qcom,spmi:pmic@2:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip3: (c440000.qcom,spmi:pmic@4:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip4: (c440000.qcom,spmi:pmic@a:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
There is a race condition exist during termination. The path is
alx_stop and then alx_remove. An alx_schedule_link_check could be called
before alx_stop by interrupt handler and invoke alx_link_check later.
Alx_stop frees the napis, and alx_remove cancels any pending works.
If any of the work is scheduled before termination and invoked before
alx_remove, a null-ptr-deref occurs because both expect alx->napis[i].
This patch fix the race condition by moving cancel_work_sync functions
before alx_free_napis inside alx_stop. Because interrupt handler can call
alx_schedule_link_check again, alx_free_irq is moved before
cancel_work_sync calls too.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VNIC driver's "login" command sequence is the final step
in the driver's initialization process with device firmware,
confirming the available device queue resources to be utilized
by the driver. Under high system load, firmware may not respond
to the request in a timely manner or may abort the request. In
such cases, the driver should reattempt the login command
sequence. In case of a device error, the number of retries
is bounded.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The argument passed to cmpxchg is not guaranteed to be sign
extended, but lr.w sign extends on RV64I. This makes cmpxchg
fail on clang built kernels when __old is negative.
To fix this, we just cast __old to long which sign extends on
RV64I. With this fix, clang built RISC-V kernels now boot.
BUG: KASAN: use-after-free in ata_scsi_mode_select_xlat+0x10bd/0x10f0
drivers/ata/libata-scsi.c:4045
Read of size 1 at addr ffff88803b8cd003 by task syz-executor.6/12621
Memory state around the buggy address: ffff88803b8ccf00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88803b8ccf80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88803b8cd000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88803b8cd080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88803b8cd100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
You can refer to "https://www.lkml.org/lkml/2019/1/17/474" reproduce
this error.
The exception code is "bd_len = p[3];", "p" value is ffff88803b8cd000
which belongs to the cache kmalloc-512 of size 512. The "page_address(sg_page(scsi_sglist(scmd)))"
maybe from sg_scsi_ioctl function "buffer" which allocated by kzalloc, so "buffer"
may not page aligned.
This also looks completely buggy on highmem systems and really needs to use a
kmap_atomic. --Christoph Hellwig
To address above bugs, Paolo Bonzini advise to simpler to just make a char array
of size CACHE_MPAGE_LEN+8+8+4-2(or just 64 to make it easy), use sg_copy_to_buffer
to copy from the sglist into the buffer, and workthere.
Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count. Call pm_runtime_put if
pm_runtime_get_sync fails.
Which means that setup_new_dl_entity() has been called on a task
currently boosted. This shouldn't happen though, as setup_new_dl_entity()
is only called when the 'dynamic' deadline of the new entity
is in the past w.r.t. rq_clock and boosted tasks shouldn't verify this
condition.
Digging through the PI code I noticed that what above might in fact happen
if an RT tasks blocks on an rt_mutex hold by a DEADLINE task. In the
first branch of boosting conditions we check only if a pi_task 'dynamic'
deadline is earlier than mutex holder's and in this case we set mutex
holder to be dl_boosted. However, since RT 'dynamic' deadlines are only
initialized if such tasks get boosted at some point (or if they become
DEADLINE of course), in general RT 'dynamic' deadlines are usually equal
to 0 and this verifies the aforementioned condition.
Fix it by checking that the potential donor task is actually (even if
temporary because in turn boosted) running at DEADLINE priority before
using its 'dynamic' deadline value.
Fixes: 2d3d891d3344 ("sched/deadline: Add SCHED_DEADLINE inheritance logic") Reported-by: syzbot+119ba87189432ead09b4@syzkaller.appspotmail.com Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com> Tested-by: Daniel Wagner <dwagner@suse.de> Link: https://lkml.kernel.org/r/20181119153201.GB2119@localhost.localdomain Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported the following warning triggered via SYSC_sched_setattr():
WARNING: CPU: 0 PID: 6973 at kernel/sched/deadline.c:593 setup_new_dl_entity /kernel/sched/deadline.c:594 [inline]
WARNING: CPU: 0 PID: 6973 at kernel/sched/deadline.c:593 enqueue_dl_entity /kernel/sched/deadline.c:1370 [inline]
WARNING: CPU: 0 PID: 6973 at kernel/sched/deadline.c:593 enqueue_task_dl+0x1c17/0x2ba0 /kernel/sched/deadline.c:1441
This happens because the ->dl_boosted flag is currently not initialized by
__dl_clear_params() (unlike the other flags) and setup_new_dl_entity()
rightfully complains about it.
If the i2c bus driver ignores the I2C_M_RECV_LEN flag (as some of
them do), it is possible for an I2C_SMBUS_BLOCK_DATA read issued
on some random device to return an arbitrary value in the first
byte (and nothing else). When this happens, i2c_smbus_xfer_emulated()
will happily write past the end of the supplied data buffer, thus
causing Bad Things to happen. To prevent this, check the size
before copying the data block and return an error if it is too large.
Fixes: 209d27c3b167 ("i2c: Emulate SMBus block read over I2C") Signed-off-by: Mans Rullgard <mans@mansr.com>
[wsa: use better errno] Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The port number field in the status register was not correct, so fix it.
Fixes: d6ffb6300116 ("i2c: Add FSI-attached I2C master algorithm") Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The (struct __prci_data).hw_clks.hws is an array with dynamic elements.
Using struct_size(pd, hw_clks.hws, ARRAY_SIZE(__prci_init_clocks))
instead of sizeof(*pd) to get the correct memory size of
struct __prci_data for sifive/fu540-prci. After applying this
modifications, the kernel runs smoothly with CONFIG_SLAB_FREELIST_RANDOM
enabled on the HiFive unleashed board.
Fixes: 30b8e27e3b58 ("clk: sifive: add a driver for the SiFive FU540 PRCI IP block") Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When commit 474ea9cafc45 ("net: bcmgenet: correctly pad short
packets") added the call to skb_padto() it should have been
located before the nr_frags parameter was read since that value
could be changed when padding packets with lengths between 55
and 59 bytes (inclusive).
The use of a stale nr_frags value can cause corruption of the
pad data when tx-scatter-gather is enabled. This corruption of
the pad can cause invalid checksum computation when hardware
offload of tx-checksum is also enabled.
Since the original reason for the padding was corrected by
commit 7dd399130efb ("net: bcmgenet: fix skb_len in
bcmgenet_xmit_single()") we can remove the software padding all
together and make use of hardware padding of short frames as
long as the hardware also always appends the FCS value to the
frame.
Fixes: 474ea9cafc45 ("net: bcmgenet: correctly pad short packets") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using ip_set with counters and comment, traffic causes the kernel
to panic on 32-bit ARM:
Alignment trap: not handling instruction e1b82f9f at [<bf01b0dc>]
Unhandled fault: alignment exception (0x221) at 0xea08133c
PC is at ip_set_match_extensions+0xe0/0x224 [ip_set]
The problem occurs when we try to update the 64-bit counters - the
faulting address above is not 64-bit aligned. The problem occurs
due to the way elements are allocated, for example:
If the element has a requirement for a member to be 64-bit aligned,
and set->dsize is not a multiple of 8, but is a multiple of four,
then every odd numbered elements will be misaligned - and hitting
an atomic64_add() on that element will cause the kernel to panic.
ip_set_elem_len() must return a size that is rounded to the maximum
alignment of any extension field stored in the element. This change
ensures that is the case.
Fixes: 95ad1f4a9358 ("netfilter: ipset: Fix extension alignment") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Right now ns->head->lock is protecting namespace mutation
which is wrong and unneeded. Move it to only protect
against head mutations. While we're at it, remove unnecessary
ns->head reference as we already have head pointer.
The problem with this is that the head->lock spans
mpath disk node I/O that may block under some conditions (if
for example the controller is disconnecting or the path
became inaccessible), The locking scheme does not allow any
other path to enable itself, preventing blocked I/O to complete
and forward-progress from there.
This is a preparation patch for the fix in a subsequent patch
where the disk I/O will also be done outside the head->lock.
Fixes: 0d0b660f214d ("nvme: add ANA support") Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver assumed that dmaengine_tx_status() could return
the residue even if the transfer was completed. However,
this was not correct usage [1] and this caused to break getting
the residue after the commit 24461d9792c2 ("dmaengine:
virt-dma: Fix access after free in vchan_complete()") actually.
So, this is possible to get wrong received size if the usb
controller gets a short packet. For example, g_zero driver
causes "bad OUT byte" errors.
The usb-dmac driver will support the callback_result, so this
driver can use it to get residue correctly. Note that even if
the usb-dmac driver has not supported the callback_result yet,
this patch doesn't cause any side-effects.
If this is in "transceiver" mode the the ->qwork isn't required and is
a NULL pointer. This can lead to a NULL dereference when we call
destroy_workqueue(udc->qwork).
Fixes: 3517c31a8ece ("usb: gadget: mv_udc: use devm_xxx for probe") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit cdb42becdd40 ("scsi: lpfc: Replace io_channels for nvme and fcp with
general hdw_queues per cpu") has introduced static checker warnings for
potential null dereferences in 'lpfc_sli4_hba_unset()' and commit 1ffdd2c0440d
("scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset") has
tried to fix it. However, yet another potential null dereference is
remaining. This commit fixes it.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Link: https://lore.kernel.org/r/20200623084122.30633-1-sjpark@amazon.com Fixes: 1ffdd2c0440d ("scsi: lpfc: resolve static checker warning inlpfc_sli4_hba_unset") Fixes: cdb42becdd40 ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu") Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: SeongJae Park <sjpark@amazon.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
if of_find_device_by_node() succeed, imx_suspend_alloc_ocram() doesn't
have a corresponding put_device(). Thus add a jump target to fix the
exception handling for this function implementation.
Fixes: 1579c7b9fe01 ("ARM: imx53: Set DDR pins to high impedance when in suspend to RAM.") Signed-off-by: yu kuai <yukuai3@huawei.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set edev->cdev pointer to NULL after calling remove() callback to avoid
using of already freed object.
Fixes: ccc67ef50b90 ("qede: Error recovery process") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently PTP cyclecounter and timecounter are initialized only on
the first probing and are cleaned up during removal. This means that
PTP becomes non-functional after device recovery.
Fix this by unconditional PTP initialization on probing and clearing
Tx pending bit on exiting.
Fixes: ccc67ef50b90 ("qede: Error recovery process") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is likely a copy'n'paste mistake. The amount of ILT lines to
reserve for a single VF was being multiplied by the total VFs count.
This led to a huge redundancy in reservation and potential lines
drainouts.
Fixes: 1408cc1fa48c ("qed: Introduce VFs") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
25ms sleep cycles in waiting for PF response are excessive and may lead
to different timeout failures.
Start to wait with short udelays, and in most cases polling will end
here. If the time was not sufficient, switch to msleeps.
usleep_range() may go far beyond 100us depending on platform and tick
configuration, hence atomic udelays for consistency.
Also add explicit DMA barriers since 'done' always comes from a shared
request-response DMA pool, and note that in the comment nearby.
Fixes: 1408cc1fa48c ("qed: Introduce VFs") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set rdma_wq pointer to NULL after destroying the workqueue and check
for it when adding new events to fix crashes on driver unload.
Fixes: cee9fbd8e2e9 ("qede: Add qedr framework") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
qed_spq_unregister_async_cb() should be called before
qed_rdma_info_free() to avoid crash-spawning uses-after-free.
Instead of calling it from each subsystem exit code, do it in one place
on PF down.
Fixes: 291d57f67d24 ("qed: Fix rdma_info structure allocation") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
qed_chain_get_element_left{,_u32} returned 0 when the difference
between producer and consumer page count was equal to the total
page count.
Fix this by conditional expanding of producer value (vs
unconditional). This allowed to eliminate normalizaton against
total page count, which was the cause of this bug.
Misc: replace open-coded constants with common defines.
Fixes: a91eb52abb50 ("qed: Revisit chain implementation") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Scalable-mode Page-walk Coherency (SMPWC) field in the VT-d extended
capability register indicates the hardware coherency behavior on paging
structures accessed through the pasid table entry. This is ignored in
current code and using ECAP.C instead which is only valid in legacy mode.
Fix this so that paging structure updates could be manually flushed from
the cache line if hardware page walking is not snooped.
Fixes: 765b6a98c1de3 ("iommu/vt-d: Enumerate the scalable mode capability") Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Cc: Ashok Raj <ashok.raj@intel.com> Cc: Kevin Tian <kevin.tian@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Link: https://lore.kernel.org/r/20200622231345.29722-6-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
PCI ACS is disabled if Intel IOMMU is off by default or intel_iommu=off
is used in command line. Unfortunately, Intel IOMMU will be forced on if
there're devices sitting on an external facing PCI port that is marked
as untrusted (for example, thunderbolt peripherals). That means, PCI ACS
is disabled while Intel IOMMU is forced on to isolate those devices. As
the result, the devices of an MFD will be grouped by a single group even
the ACS is supported on device.
[ 0.691263] pci 0000:00:07.1: Adding to iommu group 3
[ 0.691277] pci 0000:00:07.2: Adding to iommu group 3
[ 0.691292] pci 0000:00:07.3: Adding to iommu group 3
Fix it by requesting PCI ACS when Intel IOMMU is detected with platform
opt in hint.
Fixes: 89a6079df791a ("iommu/vt-d: Force IOMMU on for platform opt in hint") Co-developed-by: Lalithambika Krishnakumar <lalithambika.krishnakumar@intel.com> Signed-off-by: Lalithambika Krishnakumar <lalithambika.krishnakumar@intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Ashok Raj <ashok.raj@intel.com> Link: https://lore.kernel.org/r/20200622231345.29722-5-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ETF qdisc can queue skbs that it could not pace on the errqueue.
Address a few issues in the selftest
- recv buffer size was too small, and incorrectly calculated
- compared errno to ee_code instead of ee_errno
- missed invalid request error type
v2:
- fix a few checkpatch --strict indentation warnings
Fixes: ea6a547669b3 ("selftests/net: make so_txtime more robust to timer variance") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ib_dma_mapping_error() returns non-zero value,
ib_mad_post_receive_mads() will jump out of loops and return -ENOMEM
without freeing mad_priv. Fix this memory-leak problem by freeing mad_priv
in this case.
Fixes: 2c34e68f4261 ("IB/mad: Check and handle potential DMA mapping errors") Link: https://lore.kernel.org/r/20200612063824.180611-1-guofan5@huawei.com Signed-off-by: Fan Guo <guofan5@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current(?) OSA devices also store their cmd-specific return codes for
SET_ACCESS_CONTROL cmds into the top-level cmd->hdr.return_code.
So once we added stricter checking for the top-level field a while ago,
none of the error logic that rolls back the user's configuration to its
old state is applied any longer.
For this specific cmd, go back to the old model where we peek into the
cmd structure even though the top-level field indicated an error.
Fixes: 686c97ee29c8 ("s390/qeth: fix error handling in adapter command callbacks") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not called in
error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.
Fixes: fc05a5b22253 ("ASoC: rockchip: add support for pdm controller") Signed-off-by: Qiushi Wu <wu000273@umn.edu> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20200613205158.27296-1-wu000273@umn.edu Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 4c21b5bcef73 ("IB/cma: Add net_dev and private data checks to RDMA CM") Link: https://lore.kernel.org/r/20200616104304.2426081-1-leon@kernel.org Signed-off-by: Mark Zhang <markz@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Private data passed to iwarp_cm_handler is copied for connection request /
response, but ignored otherwise. If junk is passed, it is stored in the
event and used later in the event processing.
The driver passes an old junk pointer during connection close which leads
to a use-after-free on event processing. Set private data to NULL for
events that don 't have private data.
In case of failure of alloc_ud_wq_attr(), the memory allocated by
rvt_alloc_rq() is not freed. Fix it by calling rvt_free_rq() using the
existing clean-up code.
Fixes: d310c4bf8aea ("IB/{rdmavt, hfi1, qib}: Remove AH refcount for UD QPs") Link: https://lore.kernel.org/r/20200614041148.131983-1-pakki001@umn.edu Signed-off-by: Aditya Pakki <pakki001@umn.edu> Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The handling of the receive window size (rwind) from a received ACK packet
is not correct. The rxrpc_input_ackinfo() function currently checks the
current Tx window size against the rwind from the ACK to see if it has
changed, but then limits the rwind size before storing it in the tx_winsize
member and, if it increased, wake up the transmitting process. This means
that if rwind > RXRPC_RXTX_BUFF_SIZE - 1, this path will always be
followed.
Fix this by limiting rwind before we compare it to tx_winsize.
The effect of this can be seen by enabling the rxrpc_rx_rwind_change
tracepoint.
Fixes: 702f2ac87a9a ("rxrpc: Wake up the transmitter if Rx window size increases on the peer") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The FA2 mailbox is specified at 0x18025000 but should actually be
0x18025c00, length 0x400 according to socregs_nsp.h and board_bu.c. Also
the interrupt was off by one and should be GIC SPI 151 instead of 150.
Attaching to these hooks can break iptables because its optval is
usually quite big, or at least bigger than the current PAGE_SIZE limit.
David also mentioned some SCTP options can be big (around 256k).
For such optvals we expose only the first PAGE_SIZE bytes to
the BPF program. BPF program has two options:
1. Set ctx->optlen to 0 to indicate that the BPF's optval
should be ignored and the kernel should use original userspace
value.
2. Set ctx->optlen to something that's smaller than the PAGE_SIZE.
v5:
* use ctx->optlen == 0 with trimmed buffer (Alexei Starovoitov)
* update the docs accordingly
v4:
* use temporary buffer to avoid optval == optval_end == NULL;
this removes the corner case in the verifier that might assume
non-zero PTR_TO_PACKET/PTR_TO_PACKET_END.
v3:
* don't increase the limit, bypass the argument
v2:
* proper comments formatting (Jakub Kicinski)
Fixes: 0d01da6afc54 ("bpf: implement getsockopt and setsockopt hooks") Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Cc: David Laight <David.Laight@ACULAB.COM> Link: https://lore.kernel.org/bpf/20200617010416.93086-1-sdf@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzkaller discovered that creating a hash of type devmap_hash with a large
number of entries can hit the memory allocator limit for allocating
contiguous memory regions. There's really no reason to use kmalloc_array()
directly in the devmap code, so just switch it to the existing
bpf_map_area_alloc() function that is used elsewhere.
Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200616142829.114173-1-toke@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The callers don't expect *d_cdp to be set to an error pointer, they only
check for NULL. This leads to a static checker warning:
arch/x86/kernel/cpu/resctrl/rdtgroup.c:2648 __init_one_rdt_domain()
warn: 'd_cdp' could be an error pointer
This would not trigger a bug in this specific case because
__init_one_rdt_domain() calls it with a valid domain that would not have
a negative id and thus not trigger the return of the ERR_PTR(). If this
was a negative domain id then the call to rdt_find_domain() in
domain_add_cpu() would have returned the ERR_PTR() much earlier and the
creation of the domain with an invalid id would have been prevented.
Even though a bug is not triggered currently the right and safe thing to
do is to set the pointer to NULL because that is what can be checked for
when the caller is handling the CDP and non-CDP cases.
While testing the recent suspend and resume regressions I noticed that
duovero can still end up losing edge gpio interrupts on runtime
suspend. This causes NFSroot easily stopping working after resume on
duovero.
Let's fix the issue by using gpio level interrupts for smsc as then
the gpio interrupt state is seen by the gpio controller on resume.
Fixes: 731b409878a3 ("ARM: dts: Configure duovero for to allow core retention during idle") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
AM3358 pin mcasp0_aclkr (ZCZ ball B13) [0] is routed to P1.31 header [1]
Mode 4 of this pin is mmc0_sdwp (SD Write Protect). A signal connected
to P1.31 may accidentally trigger mmc0 write protection. To avoid this
situation, do not put mcasp0_aclkr in mode 4 (mmc0_sdwp) by default.
Memset on the pointer right after malloc can cause a NULL pointer
deference if it failed to allocate memory. A simple fix is to
replace malloc()/memset() pair with a simple call to calloc().
Fixes: 0fca931a6f21 ("samples/bpf: program demonstrating access to xdp_rxq_info") Signed-off-by: Gaurav Singh <gaurav1086@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
xdp_redirect_cpu is currently failing in bpf_prog_load_xattr()
allocating cpu_map map if CONFIG_NR_CPUS is less than 64 since
cpu_map_alloc() requires max_entries to be less than NR_CPUS.
Set cpu_map max_entries according to NR_CPUS in xdp_redirect_cpu_kern.c
and get currently running cpus in xdp_redirect_cpu_user.c
In Normal mode and Network mode, the Word Length Control bits
control the word length divider in clock generator, which is
different with I2S Master mode (the word length is fixed to
32bit), it should be the value of params_width(hw_params).
The condition "slots == 2" is not good for I2S Master mode,
because for Network mode and Normal mode, the slots can also
be 2. Then we need to use (ssi->i2s_net & SSI_SCR_I2S_MODE_MASK)
to check if it is I2S Master mode.
So we refine the formula for mono channel, otherwise there
will be sound issue for S24_LE.
PFUZE100_SWB_REG is not proper for sw1a/sw2, because enable_mask/enable_reg
is not correct. On PFUZE3000, sw1a/sw2 should be the same as sw1a/sw2 on
pfuze100 except that voltages are not linear, so add new PFUZE3000_SW_REG
and pfuze3000_sw_regulator_ops which like the non-linear PFUZE100_SW_REG
and pfuze100_sw_regulator_ops.
Fixes: 1dced996ee70 ("regulator: pfuze100: update voltage setting for pfuze3000 sw1a") Reported-by: Christophe Meynard <Christophe.Meynard@ign.fr> Signed-off-by: Robin Gong <yibin.gong@nxp.com> Link: https://lore.kernel.org/r/1592171648-8752-1-git-send-email-yibin.gong@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently both FE and BE dai-links are configured bi-directional,
However the DSP BE dais are only single directional,
so set the directions as supported by the BE dais.
Fixes: c25e295cd77b (ASoC: qcom: Add support to parse common audio device nodes) Reported-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20200612123711.29130-2-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
It is possible that the first event in the event log is not actually a
log header at all, but rather a normal event. This leads to the cast in
__calc_tpm2_event_size being an invalid conversion, which means that
the values read are effectively garbage. Depending on the first event's
contents, this leads either to apparently normal behaviour, a crash or
a freeze.
While this behaviour of the firmware is not in accordance with the
TCG Client EFI Specification, this happens on a Dell Precision 5510
with the TPM enabled but hidden from the OS ("TPM On" disabled, state
otherwise untouched). The EFI firmware claims that the TPM is present
and active and that it supports the TCG 2.0 event log format.
Fortunately, this can be worked around by simply checking the header
of the first event and the event log header signature itself.
Commit b4f1874c6216 ("tpm: check event log version before reading final
events") addressed a similar issue also found on Dell models.
Fixes: 6b0326190205 ("efi: Attempt to get the TCG2 event log in the boot stub") Signed-off-by: Fabian Vogt <fvogt@suse.de> Link: https://lore.kernel.org/r/1927248.evlx2EsYKh@linux-e202.suse.de
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1165773 Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Successful send of EOS command does not indicate that EOS is actually
finished, correct event to wait EOS is finished is EOS_RENDERED event.
EOS_RENDERED means that the DSP has finished processing all the buffers
for that particular session and stream.
This patch fixes EOS handling!
Fixes: 68fd8480bb7b ("ASoC: qdsp6: q6asm: Add support to audio stream apis") Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20200611124159.20742-3-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During IPsec performance testing, we see bad ICMP checksum. The error packet
has duplicated ESP trailer due to double validate_xmit_xfrm calls. The first call
is from ip_output, but the packet cannot be sent because
netif_xmit_frozen_or_stopped is true and the packet gets dev_requeue_skb. The second
call is from NET_TX softirq. However after the first call, the packet already
has the ESP trailer.
Fix by marking the skb with XFRM_XMIT bit after the packet is handled by
validate_xmit_xfrm to avoid duplicate ESP trailer insertion.
Fixes: f6e27114a60a ("net: Add a xfrm validate function to validate_xmit_skb") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Boris Pismenny <borisp@mellanox.com> Reviewed-by: Raed Salem <raeds@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We must check for "dss_core" instead of "dss" to avoid also matching
also "dss_dispc". This only matters for the mixed case of data
configured in device tree but with legacy booting ti,hwmods property
still enabled.
Fixes: 8b30919a4e3c ("ARM: OMAP2+: Handle reset quirks for dynamically allocated modules") Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We must ignore the clockactivity bit for most modules and not set it
unless specified for the module with SYSC_QUIRK_USE_CLOCKACT. Otherwise
the interface clock can be automatically gated constantly causing
unexpected performance issues.
Fixes: ae9ae12e9daa ("bus: ti-sysc: Handle clockactivity for enable and disable") Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Looks like we're missing flush of posted write after module enable and
disable. I've seen occasional errors accessing various modules, and it
is suspected that the lack of posted writes can also cause random reboots.
The errors we can see are similar to the one below from spi for example:
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read): Data Access
in User mode during Functional access
...
mcspi_wait_for_reg_bit
omap2_mcspi_transfer_one
spi_transfer_one_message
...
We also want to also flush posted write for disable. The clkctrl clock
disable happens after module disable, and we don't want to have the
module potentially stay active while we're trying to disable the clock.
When the try_module_get calls were removed from opening and closing of the
i2c debugfs file, the corresponding module_put calls were missed. This
results in an inaccurate module use count that requires a power cycle to
fix.
Fixes: 09fbca8e6240 ("IB/hfi1: No need to use try_module_get for debugfs") Link: https://lore.kernel.org/r/20200623203230.106975.76240.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by: Kaike Wan <kaike.wan@intel.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a filesystem is mounted on a loop device and on a loop ioctl
LOOP_SET_STATUS64, because of kill_bdev, buffer_head mappings are getting
destroyed.
kill_bdev
truncate_inode_pages
truncate_inode_pages_range
do_invalidatepage
block_invalidatepage
discard_buffer -->clear BH_Mapped flag
sb_bread
__bread_gfp
bh = __getblk_gfp
-->discard_buffer clear BH_Mapped flag
__bread_slow
submit_bh
submit_bh_wbc
BUG_ON(!buffer_mapped(bh)) --> hit this BUG_ON
Fixes: 5db470e229e2 ("loop: drop caches if offset or block_size are changed") Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB_DEVICE(0x0424, 0x274e) can send data before cdc_acm is ready,
causing garbage chars on the TTY causing stray input to the shell
and/or login prompt.
Just return if xHCI is quirked to disable LPM. We can save some time
from reading registers and doing spinlocks.
Add stable tag as we want this patch together with the next one,
"Poll for U0 after disabling USB2 LPM" which fixes a suspend issue
for some USB2 LPM devices
Unable to complete the enumeration of a USB TV Tuner device.
Per XHCI spec (4.6.5), the EP state field of the input context shall
be cleared for a set address command. In the special case of an FS
device that has "MaxPacketSize0 = 8", the Linux XHCI driver does
not do this before evaluating the context. With an XHCI controller
that checks the EP state field for parameter context error this
causes a problem in cases such as the device getting reset again
after enumeration.
When that field is cleared, the problem does not occur.
This was found and fixed by Sasi Kumar.
Cc: stable@vger.kernel.org Signed-off-by: Al Cooper <alcooperx@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci spec 6.2.3 shows that the EP state field in the endpoint context data
structure consist of bits [2:0].
The old value included a bit from the next field which fortunately is a
RsvdZ region. So hopefully this hasn't caused too much harm
CIFS implements the fallocate(FALLOC_FL_ZERO_RANGE) with send SMB
ioctl(FSCTL_SET_ZERO_DATA) to server. It just set the range of the
remote file to zero, but local page cache not update, then the data
inconsistent with server, which leads the xfstest generic/008 failed.
So we need to remove the local page caches before send SMB
ioctl(FSCTL_SET_ZERO_DATA) to server. After next read, it will
re-cache it.
Fixes: 30175628bf7f5 ("[SMB3] Enable fallocate -z support for SMB3 mounts") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Cc: stable@vger.kernel.org # v3.17 Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When punch hole success, we also can read old data from file:
# strace -e trace=pread64,fallocate xfs_io -f -c "pread 20 40" \
-c "fpunch 20 40" -c"pread 20 40" file
pread64(3, " version 5.8.0-rc1+"..., 40, 20) = 40
fallocate(3, FALLOC_FL_KEEP_SIZE|FALLOC_FL_PUNCH_HOLE, 20, 40) = 0
pread64(3, " version 5.8.0-rc1+"..., 40, 20) = 40
CIFS implements the fallocate(FALLOCATE_FL_PUNCH_HOLE) with send SMB
ioctl(FSCTL_SET_ZERO_DATA) to server. It just set the range of the
remote file to zero, but local page caches not updated, then the
local page caches inconsistent with server.
Also can be found by xfstests generic/316.
So, we need to remove the page caches before send the SMB
ioctl(FSCTL_SET_ZERO_DATA) to server.
Fixes: 31742c5a33176 ("enable fallocate punch hole ("fallocate -p") for SMB3") Suggested-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com> Cc: stable@vger.kernel.org # v3.17 Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
open_shroot() invokes kref_get(), which increases the refcount of the
"tcon->crfid" object. When open_shroot() returns not zero, it means the
open operation failed and close_shroot() will not be called to decrement
the refcount of the "tcon->crfid".
The reference counting issue happens in one normal path of
open_shroot(). When the cached root have been opened successfully in a
concurrent process, the function increases the refcount and jump to
"oshr_free" to return. However the current return value "rc" may not
equal to 0, thus the increased refcount will not be balanced outside the
function, causing a refcnt leak.
Fix this issue by setting the value of "rc" to 0 before jumping to
"oshr_free" label.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose that, for unrelated reasons, FSF requests on behalf of recovery are
very slow and can run into the ERP timeout.
In the case at hand, we did adapter recovery to a large degree. However
due to the slowness a LUN open is pending so the corresponding fc_rport
remains blocked. After fast_io_fail_tmo we trigger close physical port
recovery for the port under which the LUN should have been opened. The new
higher order port recovery dismisses the pending LUN open ERP action and
dismisses the pending LUN open FSF request. Such dismissal decouples the
ERP action from the pending corresponding FSF request by setting
zfcp_fsf_req->erp_action to NULL (among other things)
[zfcp_erp_strategy_check_fsfreq()].
If now the ERP timeout for the pending open LUN request runs out, we must
not use zfcp_fsf_req->erp_action in the ERP timeout handler. This is a
problem since v4.15 commit 75492a51568b ("s390/scsi: Convert timers to use
timer_setup()"). Before that we intentionally only passed zfcp_erp_action
as context argument to zfcp_erp_timeout_handler().
Note: The lifetime of the corresponding zfcp_fsf_req object continues until
a (late) response or an (unrelated) adapter recovery.
Just like the regular response path ignores dismissed requests
[zfcp_fsf_req_complete() => zfcp_fsf_protstatus_eval() => return early] the
ERP timeout handler now needs to ignore dismissed requests. So simply
return early in the ERP timeout handler if the FSF request is marked as
dismissed in its status flags. To protect against the race where
zfcp_erp_strategy_check_fsfreq() dismisses and sets
zfcp_fsf_req->erp_action to NULL after our previous status flag check,
return early if zfcp_fsf_req->erp_action is NULL. After all, the former
ERP action does not need to be woken up as that was already done as part of
the dismissal above [zfcp_erp_action_dismiss()].
This fixes the following panic due to kernel page fault in IRQ context:
The driver performs SCR (state change registration) in all modes including
pure target mode.
For each RSCN, scan_needed flag is set in qla2x00_handle_rscn() for the
port mentioned in the RSCN and fabric rescan is scheduled. During the
rescan, GNN_FT handler, qla24xx_async_gnnft_done() deletes session of the
port that caused the RSCN.
In target mode, the session deletion has an impact on ATIO handler,
qlt_24xx_atio_pkt(). Target responds with SAM STATUS BUSY to I/O incoming
from the deleted session. qlt_handle_cmd_for_atio() and
qlt_handle_task_mgmt() return -EFAULT if they are not able to find session
of the command/TMF, and that results in invocation of qlt_send_busy():
qlt_24xx_atio_pkt_all_vps: qla_target(0): type 6 ox_id 0014
qla_target(0): Unable to send command to target, sending BUSY status
Such response causes command timeout on the initiator. Error handler thread
on the initiator will be spawned to abort the commands:
Command abort is rejected by target and fails (2003), error handler then
tries to perform DEVICE RESET and TARGET RESET but they're also doomed to
fail because TMFs are ignored for the deleted sessions.
Then initiator makes BUS RESET that resets the link via
qla2x00_full_login_lip(). BUS RESET succeeds and brings initiator port up,
SAN switch detects that and sends RSCN to the target port and it fails
again the same way as described above. It never goes out of the loop.
The change breaks the RSCN loop by keeping initiator sessions mentioned in
RSCN payload in all modes, including dual and pure target mode.
Link: https://lore.kernel.org/r/20200605144435.27023-1-r.bolshakov@yadro.com Fixes: 2037ce49d30a ("scsi: qla2xxx: Fix stale session") Cc: Quinn Tran <qutran@marvell.com> Cc: Arun Easi <aeasi@marvell.com> Cc: Nilesh Javali <njavali@marvell.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Daniel Wagner <dwagner@suse.de> Cc: Himanshu Madhani <himanshu.madhani@oracle.com> Cc: Martin Wilck <mwilck@suse.com> Cc: stable@vger.kernel.org # v5.4+ Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Shyam Sundar <ssundar@marvell.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
The USB-audio mixer code holds a linked list of usb_mixer_elem_list,
and several operations are performed for each mixer element. A few of
them (snd_usb_mixer_notify_id() and snd_usb_mixer_interrupt_v2())
assume each mixer element being a usb_mixer_elem_info object that is a
subclass of usb_mixer_elem_list, cast via container_of() and access it
members. This may result in an out-of-bound access when a
non-standard list element has been added, as spotted by syzkaller
recently.
This patch adds a new field, is_std_info, in usb_mixer_elem_list to
indicate that the element is the usb_mixer_elem_info type or not, and
skip the access to such an element if needed.
We've found Samsung USBC Headset (AKG) (VID: 0x04e8, PID: 0xa051)
need a tiny delay after each class compliant request.
Otherwise the device might not be able to be recognized each times.
fix error "clock source 41 is not valid, cannot use"
[] New USB device found, idVendor=154e, idProduct=1002, bcdDevice= 1.00
[] New USB device strings: Mfr=1, Product=2, SerialNumber=0
[] Product: DCD-1500RE
[] Manufacturer: D & M Holdings Inc.
[]
[] clock source 41 is not valid, cannot use
[] usbcore: registered new interface driver snd-usb-audio
John reported screaming irq caused by rt1711h when system boot[1],
this is because irq request is done before tcpci_register_port(),
so the chip->tcpci has not been setup, irq handler is entered but
can't do anything, this patch is to address this by moving the irq
request after tcpci_register_port().
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ehci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
When runtime suspend was enabled, runtime suspend might happen
when xhci is removing hcd. This might cause kernel panic when hcd
has been freed but runtime pm suspend related handle need to
reference it.
A Synopsys USB2.0 core used in Huawei Kunpeng920 SoC has a bug which
might cause the host controller not issuing ping.
Bug description:
After indicating an Interrupt on Async Advance, the software uses the
doorbell mechanism to delete the Next Link queue head of the last
executed queue head. At this time, the host controller still references
the removed queue head(the queue head is NULL). NULL reference causes
the host controller to lose the USB device.
Solution:
After deleting the Next Link queue head, when has_synopsys_hc_bug set
to 1，the software can write one of the valid queue head addresses to
the ASYNCLISTADDR register to allow the host controller to get
the valid queue head. in order to solve that problem, this patch set
the flag for Huawei Kunpeng920
There are detailed instructions and solutions in this patch:
commit 2f7ac6c19997 ("USB: ehci: add workaround for Synopsys HC bug")
During dwc2 driver probe, after gadget registration to the udc class
driver, if exist any builtin function driver it immediately bound to
dwc2 and after init host side (dwc2_hcd_init()) stucked in host mode.
Patch postpone gadget registration after host side initialization done.
Fixes: 117777b2c3bb9 ("usb: dwc2: Move gadget probe function into platform code") Reported-by: kbuild test robot <lkp@intel.com> Tested-by: Marek Vasut <marex@denx.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Minas Harutyunyan <hminas@synopsys.com> Link: https://lore.kernel.org/r/f21cb38fecc72a230b86155d94c7e60c9cb66f58.1591690938.git.hminas@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The binder driver makes the assumption proc->context pointer is invariant after
initialization (as documented in the kerneldoc header for struct proc).
However, in commit f0fe2c0f050d ("binder: prevent UAF for binderfs devices II")
proc->context is set to NULL during binder_deferred_release().
Another proc was in the middle of setting up a transaction to the dying
process and crashed on a NULL pointer deref on "context" which is a local
set to &proc->context:
The fix is to move the kfree of the binder_device to binder_free_proc()
so the binder_device is freed when we know there are no references
remaining on the binder_proc.
With the recent full-duplex support of implicit feedback streams, an
endpoint can be still running after closing the capture stream as long
as the playback stream with the sync-endpoint is running. In such a
state, the URBs are still be handled and they may call retire_data_urb
callback, which tries to transfer the data from the PCM buffer. Since
the PCM stream gets closed, this may lead to use-after-free.
This patch adds the proper clearance of the callback at stopping the
capture stream for addressing the possible UAF above.
Fixes: 10ce77e4817f ("ALSA: usb-audio: Add duplex sound support for USB devices using implicit feedback") Link: https://lore.kernel.org/r/20200616120921.12249-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the quiesce/activate rework, __netdev_watchdog_up() is directly
called in the ucc_geth driver.
Unfortunately, this function is not available for modules and thus
ucc_geth cannot be built as a module anymore. Fix it by exporting
__netdev_watchdog_up().
Since the commit introducing the regression was backported to stable
branches, this one should ideally be as well.
Fixes: 79dde73cf9bc ("net/ethernet/freescale: rework quiesce/activate for ucc_geth") Signed-off-by: Valentin Longchamp <valentin@longchamp.me> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing a block group, if we fail to delete the block group's item
from the extent tree, we jump to the 'out' label and end up decrementing
the block group's reference count once only (by 1), resulting in a counter
leak because the block group at that point was already removed from the
block group cache rbtree - so we have to decrement the reference count
twice, once for the rbtree and once for our lookup at the start of the
function.
There is a second bug where if removing the free space tree entries (the
call to remove_block_group_free_space()) fails we end up jumping to the
'out_put_group' label but end up decrementing the reference count only
once, when we should have done it twice, since we have already removed
the block group from the block group cache rbtree. This happens because
the reference count decrement for the rbtree reference happens after
attempting to remove the free space tree entries, which is far away from
the place where we remove the block group from the rbtree.
To make things less error prone, decrement the reference count for the
rbtree immediately after removing the block group from it. This also
eleminates the need for two different exit labels on error, renaming
'out_put_label' to just 'out' and removing the old 'out'.
Fixes: f6033c5e333238 ("btrfs: fix block group leak when removing fails") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's not safe to use pm_runtime_force_{suspend,resume}(), especially
during the noirq phase of suspend. See also the guidance provided in
commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM
and system sleep (v2)").
Mirja Kuehlewind reported a bug in Linux TCP CUBIC Hystart, where
Hystart HYSTART_DELAY mechanism can exit Slow Start spuriously on an
ACK when the minimum rtt of a connection goes down. From inspection it
is clear from the existing code that this could happen in an example
like the following:
o The first 8 RTT samples in a round trip are 150ms, resulting in a
curr_rtt of 150ms and a delay_min of 150ms.
o The 9th RTT sample is 100ms. The curr_rtt does not change after the
first 8 samples, so curr_rtt remains 150ms. But delay_min can be
lowered at any time, so delay_min falls to 100ms. The code executes
the HYSTART_DELAY comparison between curr_rtt of 150ms and delay_min
of 100ms, and the curr_rtt is declared far enough above delay_min to
force a (spurious) exit of Slow start.
The fix here is simple: allow every RTT sample in a round trip to
lower the curr_rtt.
Fixes: ae27e98a5152 ("[TCP] CUBIC v2.3") Reported-by: Mirja Kuehlewind <mirja.kuehlewind@ericsson.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I spotted a few nits when comparing the in-tree version of sch_cake with
the out-of-tree one: A redundant error variable declaration shadowing an
outer declaration, and an indentation alignment issue. Fix both of these.
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a further optimisation of the diffserv parsing codepath, we can skip it
entirely if CAKE is configured to neither use diffserv-based
classification, nor to zero out the diffserv bits.
Fixes: c87b4ecdbe8d ("sch_cake: Make sure we can write the IP header before changing DSCP bits") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cake_handle_diffserv() tries to linearize mac and network header parts of
skb and to make it writable unconditionally. In some cases it leads to full
skb reallocation, which reduces throughput and increases CPU load. Some
measurements of IPv4 forward + NAPT on MIPS router with 580 MHz single-core
CPU was conducted. It appears that on kernel 4.9 skb_try_make_writable()
reallocates skb, if skb was allocated in ethernet driver via so-called
'build skb' method from page cache (it was discovered by strange increase
of kmalloc-2048 slab at first).
Obtain DSCP value via read-only skb_header_pointer() call, and leave
linearization only for DSCP bleaching or ECN CE setting. And, as an
additional optimisation, skip diffserv parsing entirely if it is not needed
by the current configuration.
Fixes: c87b4ecdbe8d ("sch_cake: Make sure we can write the IP header before changing DSCP bits") Signed-off-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
[ fix a few style issues, reflow commit message ] Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log