In general, the three SKUs of sc7180 (lite, normal, and pro) are
handled dynamically.
The cpufreq table in sc7180.dtsi includes the superset of all CPU
frequencies. The "qcom-cpufreq-hw" driver in Linux shows that we can
dynamically detect which frequencies are actually available on the
currently running CPU and then we can just enable those ones.
The GPU is similarly dynamic. The nvmem has a fuse in it (see
"gpu_speed_bin" in sc7180.dtsi) that the GPU driver can use to figure
out which frequencies to enable.
There is one part, however, that is not so dynamic. The way SDRAM
frequency works in sc7180 is that it's tied to cpufreq. At the busiest
cpufreq operating points we'll pick the top supported SDRAM frequency.
They ramp down together.
For the "pro" SKU of sc7180, we only enable one extra cpufreq step.
That extra cpufreq step runs SDRAM at the same speed as the step
below. Thus, for normal and pro things are OK. There is no sc7180-pro
device tree snippet.
For the "lite" SKU if sc7180, however, things aren't so easy. The
"lite" SKU drops 3 cpufreq entries but can still run SDRAM at max
frequency. That messed things up with the whole scheme. This is why we
added the "sc7180-lite" fragment in commit 8fd01e01fd6f ("arm64: dts:
qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite").
When the lite scheme came about, it was agreed that the WiFi SKUs of
lazor would _always_ be "lite" and would, in fact, be the only "lite"
devices. Unfortunately, this decision changed and folks didn't realize
that it would be a problem. Specifically, some later lazor WiFi-only
devices were built with "pro" CPUs.
Building WiFi-only lazor with "pro" CPUs isn't the end of the world.
The SDRAM will ramp up a little sooner than it otherwise would, but
aside from a small power hit things work OK. One problem, though, is
that the SDRAM scaling becomes a bit quirky. Specifically, with the
current tables we'll max out SDRAM frequency at 2.1GHz but then
_lower_ it at 2.2GHz / 2.3GHz only to raise it back to max for 2.4GHz
and 2.55GHz.
Let's at least fix this so that the SDRAM frequency doesn't go down in
that quirky way. On true "lite" SKUs this change will be a no-op
because the operating points we're touching are disabled. This change
is only useful when a board that thinks it has a "lite" CPU actually
has a "normal" or "pro" one stuffed.
Fixes: 8fd01e01fd6f ("arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230515171929.1.Ic8dee2cb79ce39ffc04eab2a344dde47b2f9459f@changeid Signed-off-by: Sasha Levin <sashal@kernel.org>
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
The of_find_device_by_node() function is returning a struct platform_device
object with the embedded struct device member's reference counter
incremented. This needs to be dropped when done with the platform device
returned by of_find_device_by_node().
at91_pm_eth_quirk_is_valid() calls of_find_device_by_node() on
suspend and resume path. On suspend it calls of_find_device_by_node() and
on resume and failure paths it drops the counter of
struct platform_device::dev.
In case ethernet device may not wakeup there is a put_device() on
at91_pm_eth_quirk_is_valid() which is wrong as it colides with
put_device() on resume path leading to the reference counter of struct
device embedded in struct platform_device to be messed, stack trace to be
displayed (after 5 consecutive suspend/resume cycles) and execution to
hang.
Along with this the error path of at91_pm_config_quirks() had been also
adapted to decrement propertly the reference counter of struct device
embedded in struct platform_device.
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
The current uses of PageAnon in page table check functions can lead to
type confusion bugs between struct page and slab [1], if slab pages are
accidentally mapped into the user space. This is because slab reuses the
bits in struct page to store its internal states, which renders PageAnon
ineffective on slab pages.
Since slab pages are not expected to be mapped into the user space, this
patch adds BUG_ON(PageSlab(page)) checks to make sure that slab pages
are not inadvertently mapped. Otherwise, there must be some bugs in the
kernel.
Without EXCLUSIVE_SYSTEM_RAM, users are allowed to map arbitrary
physical memory regions into the userspace via /dev/mem. At the same
time, pages may change their properties (e.g., from anonymous pages to
named pages) while they are still being mapped in the userspace, leading
to "corruption" detected by the page table check.
To avoid these false positives, this patch makes PAGE_TABLE_CHECK
depends on EXCLUSIVE_SYSTEM_RAM. This dependency is understandable
because PAGE_TABLE_CHECK is a hardening technique but /dev/mem without
STRICT_DEVMEM (i.e., !EXCLUSIVE_SYSTEM_RAM) is itself a security
problem.
Even with EXCLUSIVE_SYSTEM_RAM, I/O pages may be still allowed to be
mapped via /dev/mem. However, these pages are always considered as named
pages, so they won't break the logic used in the page table check.
When hcd->localmem_pool is non-null, localmem_pool is used to allocate
DMA memory. In this case, the dma address will be properly returned (in
dma_handle), and dma_mmap_coherent should be used to map this memory
into the user space. However, the current implementation uses
pfn_remap_range, which is supposed to map normal pages.
Instead of repeating the logic in the memory allocation function, this
patch introduces a more robust solution. Here, the type of allocated
memory is checked by testing whether dma_handle is properly set. If
dma_handle is properly returned, it means some DMA pages are allocated
and dma_mmap_coherent should be used to map them. Otherwise, normal
pages are allocated and pfn_remap_range should be called. This ensures
that the correct mmap functions are used consistently, independently
with logic details that determine which type of memory gets allocated.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1] Fixes: f7d34b445abc ("USB: Add support for usbfs zerocopy.") Fixes: ff2437befd8f ("usb: host: Fix excessive alignment restriction for local memory allocations") Cc: stable@vger.kernel.org Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass to dev_err_probe() PTR_ERR from actual dev_pm_opp_find_bw_floor()
call which failed, instead of previous ret which at this point is 0.
Failure of dev_pm_opp_find_bw_floor() would result in prematurely ending
the probe with success.
Fixes smatch warnings:
drivers/soc/qcom/icc-bwmon.c:776 bwmon_probe() warn: passing zero to 'dev_err_probe'
drivers/soc/qcom/icc-bwmon.c:781 bwmon_probe() warn: passing zero to 'dev_err_probe'
Commit 699b045a8e43 ("net: virtio_net: notifications coalescing
support") added coalescing command support for virtio_net. However,
the coalesce commands are using buffers on the stack, which is causing
the device to see DMA errors. There should also be a complaint from
check_for_stack() in debug_dma_map_xyz(). Fix this by adding and using
coalesce params from the control_buf struct, which aligns with other
commands.
Cc: stable@vger.kernel.org Fixes: 699b045a8e43 ("net: virtio_net: notifications coalescing support") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Allen Hubbe <allen.hubbe@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20230605195925.51625-1-brett.creeley@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move capturing the snapshot context into the image request state
machine, after exclusive lock is ensured to be held for the duration of
dealing with the image request. This is needed to ensure correctness
of fast-diff states (OBJECT_EXISTS vs OBJECT_EXISTS_CLEAN) and object
deltas computed based off of them. Otherwise the object map that is
forked for the snapshot isn't guaranteed to accurately reflect the
contents of the snapshot when the snapshot is taken under I/O. This
breaks differential backup and snapshot-based mirroring use cases with
fast-diff enabled: since some object deltas may be incomplete, the
destination image may get corrupted.
Move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting into the object request
state machine to allow for the snapshot context to be captured in the
image request state machine rather than in rbd_queue_workfn().
After TEE has completed processing of TEE_CMD_ID_LOAD_TA, set proper
value in 'return_origin' argument passed by open_session() call. To do
so, add 'return_origin' field to the structure tee_cmd_load_ta. The
Trusted OS shall update return_origin as part of TEE processing.
This change to 'struct tee_cmd_load_ta' interface requires a similar update
in AMD-TEE Trusted OS's TEE_CMD_ID_LOAD_TA interface.
This patch has been verified on Phoenix Birman setup. On older APUs,
return_origin value will be 0.
Since commit 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support
during hci down for wcn3990"), the setup callback which registers the
debugfs interface can be called multiple times.
This specifically leads to the following error when powering on the
controller:
debugfs: Directory 'ibs' with parent 'hci0' already present!
Add a driver flag to avoid trying to register the debugfs interface more
than once.
Fixes: 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990") Cc: stable@vger.kernel.org # 4.20 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ec6cef9cd98d ("Bluetooth: Fix SMP channel registration for
unconfigured controllers") the debugfs interface for unconfigured
controllers will be created when the controller is configured.
There is however currently nothing preventing a controller from being
configured multiple time (e.g. setting the device address using btmgmt)
which results in failed attempts to register the already registered
debugfs entries:
debugfs: File 'features' in directory 'hci0' already present!
debugfs: File 'manufacturer' in directory 'hci0' already present!
debugfs: File 'hci_version' in directory 'hci0' already present!
...
debugfs: File 'quirk_simultaneous_discovery' in directory 'hci0' already present!
Add a controller flag to avoid trying to register the debugfs interface
more than once.
Fixes: ec6cef9cd98d ("Bluetooth: Fix SMP channel registration for unconfigured controllers") Cc: stable@vger.kernel.org # 4.0 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit 0f7d9b31ce7a ("netfilter: nf_tables: fix use-after-free
in nft_set_catchall_destroy()"). We can not access k after kfree_rcu()
call.
Cc: stable@vger.kernel.org Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit 583d6535cb9d ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.
The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.
Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.
Fixes: 583d6535cb9d ("dasd: remove dead code") Cc: stable@vger.kernel.org # v5.0+ Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turning off the PLL and entering D0i3 will reset the VPU so
an explicit IP reset is redundant.
But if the VPU is active, it may interfere with PLL disabling
and to avoid that, we have to issue an additional IP reset
to silence the VPU before turning off the PLL.
Fixes: a8fed6d1e0b9 ("accel/ivpu: Fix power down sequence") Cc: stable@vger.kernel.org # 6.3.x Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com> Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-1-stanislaw.gruszka@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:
== Thread A == == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
...
== Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
->__send_flush_snap()
handle_cap_flushsnap_ack()
->iput('&ci->vfs_inode')
this also will release 'ci'
...
== Thread D ==
ceph_handle_snap()
->flush_snaps()
->iterate 'mdsc->snap_flush_list'
->get the stale 'ci'
->remove 'ci' from ->ihold(&ci->vfs_inode) this
'mdsc->snap_flush_list' will WARNING
To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.
To align with what is done by the in-kernel PM, update userspace pm
subflow selftests, by sending the a remove_addrs command together
before the remove_subflows command. This will get a RM_ADDR in
chk_rm_nr().
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE") Fixes: 5e986ec46874 ("selftests: mptcp: userspace pm subflow tests") Link: https://github.com/multipath-tcp/mptcp_net-next/issues/379 Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is linked to the previous commit ("mptcp: only send RM_ADDR in
nl_cmd_remove").
To align with what is done by the in-kernel PM, update userspace pm addr
selftests, by sending a remove_subflows command together after the
remove_addrs command.
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE") Fixes: 97040cf9806e ("selftests: mptcp: userspace pm address tests") Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase pm subflows counter on both server side and client side when
userspace pm creates a new subflow, and decrease the counter when it
closes a subflow.
Increase add_addr_signaled counter in mptcp_nl_cmd_announce() when the
address is announced by userspace PM.
This modification is similar to how the in-kernel PM is updating the
counter: when additional subflows are created/removed.
Fixes: 9ab4807c84a4 ("mptcp: netlink: Add MPTCP_PM_CMD_ANNOUNCE") Fixes: 702c2f646d42 ("mptcp: netlink: allow userspace-driven subflow establishment") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/329 Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the address into userspace_pm_local_addr_list when the subflow is
created. Make sure it can be found in mptcp_nl_cmd_remove(). And delete
it in the new helper mptcp_userspace_pm_delete_local_addr().
By doing this, the "REMOVE" command also works with subflows that have
been created via the "SUB_CREATE" command instead of restricting to
the addresses that have been announced via the "ANNOUNCE" command.
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE") Link: https://github.com/multipath-tcp/mptcp_net-next/issues/379 Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: use-after-free in kref_put include/linux/kref.h:64 [inline]
BUG: KASAN: use-after-free in j1939_priv_put+0x25/0xa0 net/can/j1939/main.c:172
Write of size 4 at addr ffff888141c15058 by task swapper/3/0
To avoid this, call j1939_can_rx_register() under j1939_netdev_lock so
that a concurrent thread cannot process j1939_priv before
j1939_can_rx_register() returns.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
It turns out access to j1939_can_rx_register() needs to be serialized,
otherwise j1939_priv can be corrupted when parallel threads call
j1939_netdev_start() and j1939_can_rx_register() fails. This issue is
thoroughly covered in other commit which serializes access to
j1939_can_rx_register().
Change j1939_netdev_lock type to mutex so that we do not need to remove
GFP_KERNEL from can_rx_register().
j1939_netdev_lock seems to be used in normal contexts where mutex usage
is not prohibited.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
This patch addresses an issue within the j1939_sk_send_loop_abort()
function in the j1939/socket.c file, specifically in the context of
Transport Protocol (TP) sessions.
Without this patch, when a TP session is initiated and a Clear To Send
(CTS) frame is received from the remote side requesting one data packet,
the kernel dispatches the first Data Transport (DT) frame and then waits
for the next CTS. If the remote side doesn't respond with another CTS,
the kernel aborts due to a timeout. This leads to the user-space
receiving an EPOLLERR on the socket, and the socket becomes active.
However, when trying to read the error queue from the socket with
sock.recvmsg(, , socket.MSG_ERRQUEUE), it returns -EAGAIN,
given that the socket is non-blocking. This situation results in an
infinite loop: the user-space repeatedly calls epoll(), epoll() returns
the socket file descriptor with EPOLLERR, but the socket then blocks on
the recv() of ERRQUEUE.
This patch introduces an additional check for the J1939_SOCK_ERRQUEUE
flag within the j1939_sk_send_loop_abort() function. If the flag is set,
it indicates that the application has subscribed to receive error queue
messages. In such cases, the kernel can communicate the current transfer
state via the error queue. This allows for the function to return early,
preventing the unnecessary setting of the socket into an error state,
and breaking the infinite loop. It is crucial to note that a socket
error is only needed if the application isn't using the error queue, as,
without it, the application wouldn't be aware of transfer issues.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Reported-by: David Jander <david@protonic.nl> Tested-by: David Jander <david@protonic.nl> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20230526081946.715190-1-o.rempel@pengutronix.de Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmemdup() at line 2735 is not duplicating enough memory for
notif->tid_tear_down and notif->station_id. As it only duplicates
612 bytes: up to offsetofend(struct iwl_wowlan_info_notif,
received_beacons), this is the range of [0, 612) bytes.
Fix this by allocating space for the whole notif object and zero out the
remaining space in memory after member station_id.
This also fixes the following -Warray-bounds issues:
CC drivers/net/wireless/intel/iwlwifi/mvm/d3.o
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function ‘iwl_mvm_wait_d3_notif’:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2743:30: warning: array subscript ‘struct iwl_wowlan_info_notif[0]’ is partly outside array bounds of ‘unsigned char[612]’ [-Warray-bounds=]
2743 | notif->tid_tear_down = notif_v1->tid_tear_down;
|
from drivers/net/wireless/intel/iwlwifi/mvm/d3.c:7:
In function ‘kmemdup’,
inlined from ‘iwl_mvm_wait_d3_notif’ at drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2735:12:
include/linux/fortify-string.h:765:16: note: object of size 612 allocated by ‘__real_kmemdup’
765 | return __real_kmemdup(p, size, gfp);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function ‘iwl_mvm_wait_d3_notif’:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2744:30: warning: array subscript ‘struct iwl_wowlan_info_notif[0]’ is partly outside array bounds of ‘unsigned char[612]’ [-Warray-bounds=]
2744 | notif->station_id = notif_v1->station_id;
| ^~
In function ‘kmemdup’,
inlined from ‘iwl_mvm_wait_d3_notif’ at drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2735:12:
include/linux/fortify-string.h:765:16: note: object of size 612 allocated by ‘__real_kmemdup’
765 | return __real_kmemdup(p, size, gfp);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: https://github.com/KSPP/linux/issues/306 Fixes: 905d50ddbc83 ("wifi: iwlwifi: mvm: support wowlan info notification version 2") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/ZHpGN555FwAKGduH@work Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
When going from ODM 2:1 single display case to max displays, second
odm pipe needs to be repurposed for one of the new single displays.
However, acquire_first_split_pipe() only handles MPC case and not
ODM case
[How]
Add ODM conditions in acquire_first_split_pipe()
Add commit_minimal_transition_state() in commit_streams() to handle
odm 2:1 exit first, and then process new streams
Handle ODM condition in commit_minimal_transition_state()
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Acked-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Samson Tam <samson.tam@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support") showed
improvements to power consumption over suspend when s0ix wasn't enabled in
BIOS and the system didn't support S3.
This patch however was misguided because the reason the system didn't
support S3 was because SMT was disabled in OEM BIOS setup.
This prevented the BIOS from allowing S3.
Also allowing GPUs to use the s2idle path actually causes problems if
they're invoked on systems that may not support s2idle in the platform
firmware. `systemd` has a tendency to try to use `s2idle` if `deep` fails
for any reason, which could lead to unexpected flows.
The original commit also fixed a problem during resume from suspend to idle
without hardware support, but this is no longer necessary with commit ca4751866397 ("drm/amd: Don't allow s0ix on APUs older than Raven")
Revert commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support")
to make it match the expected behavior again.
Cc: Rafael Ávila de Espíndola <rafael@espindo.la> Link: https://github.com/torvalds/linux/blob/v6.1/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c#L1060 Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2599 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Alex, most APUs from that time seem to have the same issue
(vbios says 48Mhz, actual is 100Mhz). I only have a CHIP_STONEY so I
limit the fixup to CHIP_STONEY
cmipci driver replaces the kctl->id.device after assigning the kctl
via snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-3-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUS driver replaces the kctl->id.index after assigning the kctl via
snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-4-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ymfpci driver replaces the kctl->id.device after assigning the kctl
via snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-2-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HD-audio core code replaces the kctl->id.index of SPDIF-related
controls after assigning via snd_ctl_add(). This doesn't work any
longer with the new Xarray lookup change. The change of the kctl->id
content has to be done via snd_ctl_rename_id() helper, instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-5-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the kernel increments device's open count in input_open_device()
even if device is inhibited, the counter should always be decremented in
input_close_device() to keep it balanced.
While doing my research to improve the xpad device names I noticed
that the 1532:0037 VID/PID seems to be used by the DeathAdder 2013,
so that Razer Sabertooth instance looked wrong and very suspect to
me. I didn't see any mention in the official drivers, either.
After doing more research, it turns out that the xpad list
is used by many other projects (like Steam) as-is [1], this
issue was reported [2] and Valve/Sam Lantinga fixed it [3]:
(With multiple Internet users reporting similar issues, not linked here)
After not being able to find the correct VID/PID combination anywhere
on the Internet and not receiving any reply from Razer support I did
some additional detective work, it seems like it presents itself as
"Razer Sabertooth Gaming Controller (XBOX360)", code 1689:FE00.
Leaving us with this:
* Razer Sabertooth (1689:fe00)
* Razer Sabertooth Elite (24c6:5d04)
* Razer DeathAdder 2013 (1532:0037) [note: not a gamepad]
So, to sum things up; remove this conflicting/duplicate entry:
As the real/correct one is already present there, even if
the Internet as a whole insists on presenting it as the
Razer Sabertooth Elite, which (by all accounts) is not:
Syzkaller got a lot of crashes like:
KASAN: use-after-free Write in *_timers*
All of these crashes point to the same memory area:
The buggy address belongs to the object at ffff88801f870000
which belongs to the cache kmalloc-8k of size 8192
The buggy address is located 5320 bytes inside of
8192-byte region [ffff88801f870000, ffff88801f872000)
This area belongs to :
batadv_priv->batadv_priv_dat->delayed_work->timer_list
The reason for these issues is the lack of synchronization. Delayed
work (batadv_dat_purge) schedules new timer/work while the device
is being deleted. As the result new timer/delayed work is set after
cancel_delayed_work_sync() was called. So after the device is freed
the timer list contains pointer to already freed memory.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Cc: stable@kernel.org Fixes: 2f1dfbe18507 ("batman-adv: Distributed ARP Table - implement local storage") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move GMU mutex initialization earlier to make sure that it is always
initialized. a6xx_destroy can be called from ther failure path before
GMU initialization.
Fixes: 4cd15a3e8b36 ("drm/msm/a6xx: Make GPU destroy a bit safer") Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/531540/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As per the new udp tunnel framework, drivers which need to know the
details of a port entry (i.e. port type) when it gets deleted should
use the .set_port / .unset_port callbacks.
Implementing the current .udp_tunnel_sync callback would mean that the
deleted tunnel port entry would be all zeros. This used to work on
older firmware because it would not check the input when deleting a
tunnel port. With newer firmware, the delete will now fail and
subsequent tunnel port allocation will fail as a result.
Fixes: 442a35a5a7aa ("bnxt: convert to new udp_tunnel_nic infra") Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The firmware can send PHC_RTC_UPDATE async event on a PF that may not
have PTP registered. In such a case, there will be a null pointer
deference for bp->ptp_cfg when we try to handle the event.
Fix it by not registering for this event with the firmware if !bp->ptp_cfg.
Also, check that bp->ptp_cfg is valid before proceeding when we receive
the event.
Fixes: 8bcf6f04d4a5 ("bnxt_en: Handle async event when the PHC is updated in RTC mode") Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver starts firmware fatal error recovery by detecting
heartbeat failure or fw reset count register changing. But
these checks are not reliable if the device is not accessible.
This can happen while DPC (Downstream Port containment) is in
progress. Skip firmware fatal recovery if pci_device_is_present()
returns false.
We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF. If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag. If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side. The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.
Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly. For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information. If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.
Fixes: cf6645f8ebc6 ("bnxt_en: Add function for VF driver to query default VLAN.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.
Fixes: 7a13240e3718 ("bnxt_en: fix ethtool_reset_flags ABI violations") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
irq_cpu_rmap_release() calls cpu_rmap_put(), which may free the rmap.
So we need to clear the pointer to our glue structure in rmap before
doing that, not after.
Fixes: 4e0473f1060a ("lib: cpu_rmap: Avoid use after free on rmap->obj array entries") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/ZHo0vwquhOy3FaXc@decadent.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the function of amdgpu_bo_vm_destroy to handle the resource release
of shadow bo. During the amdgpu_mes_self_test, shadow bo released, but
vmbo->shadow_list was not, which caused a null pointer reference error
in amdgpu_device_recover_vram when GPU reset.
Fixes: 6c032c37ac3e ("drm/amdgpu: Fix vram recover doesn't work after whole GPU reset (v2)") Signed-off-by: xinhui pan <xinhui.pan@amd.com> Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com> Acked-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's problem for all stable trees with bpf_d_path helper, which was
added in 5.9.
This issue is fixed in current bpf code, where we identify and mark
trusted pointers, so the above code would fail even to load.
For the sake of the stable trees and to workaround potentially broken
verifier in the future, adding the code that reads the path object from
the passed pointer and verifies it's valid in kernel space.
Fixes: 6e22ab9da793 ("bpf: Add d_path helper") Reported-by: Anastasios Papagiannis <tasos.papagiannnis@gmail.com> Suggested-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Stanislav Fomichev <sdf@google.com> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20230606181714.532998-1-jolsa@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
try_module_get will be called in tcf_proto_lookup_ops. So module_put needs
to be called to drop the refcount if ops don't implement the required
function.
Fixes: 9f407f1768d3 ("net: sched: introduce chain templates") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
net/sched/act_police.c:360:28: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:362:45: warning: dereference of noderef expression
net/sched/act_police.c:368:28: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:370:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression
net/sched/act_police.c:376:45: warning: dereference of noderef expression
Fixes: d1967e495a8d ("net_sched: act_police: add 2 new attributes to support police 64bit rate and peakrate") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the per cpu upcall counters are allocated after the vport is
created and inserted into the system. This could lead to the datapath
accessing the counters before they are allocated resulting in a kernel
Oops.
rtm_tca_policy is used from net/sched/sch_api.c and net/sched/cls_api.c,
thus should be declared in an include file.
This fixes the following sparse warning:
net/sched/sch_api.c:1434:25: warning: symbol 'rtm_tca_policy' was not declared. Should it be static?
Fixes: e331473fee3d ("net/sched: cls_api: add missing validation of netlink attributes") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current ice driver's GNSS write implementation buffers writes and
works through them asynchronously in a kthread. That's bad because:
- The GNSS write_raw operation is supposed to be synchronous[1][2].
- There is no upper bound on the number of pending writes.
Userspace can submit writes much faster than the driver can process,
consuming unlimited amounts of kernel memory.
A patch that's currently on review[3] ("[v3,net] ice: Write all GNSS
buffers instead of first one") would add one more problem:
- The possibility of waiting for a very long time to flush the write
work when doing rmmod, softlockups.
To fix these issues, simplify the implementation: Drop the buffering,
the write_work, and make the writes synchronous.
I tested this with gpsd and ubxtool.
[1] https://events19.linuxfoundation.org/wp-content/uploads/2017/12/The-GNSS-Subsystem-Johan-Hovold-Hovold-Consulting-AB.pdf
"User interface" slide.
[2] A comment in drivers/gnss/core.c:gnss_write():
/* Ignoring O_NONBLOCK, write_raw() is synchronous. */
[3] https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20230217120541.16745-1-karol.kolacinski@intel.com/
Fixes: d6b98c8d242a ("ice: add write functionality for GNSS TTY") Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add some missing error propagation in live_parallel_switch.
To avoid needlessly burdening the various backport processes, note I am
not marking it as a fix against any patches and not copying stable since
it is debug/selftests only code.
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 6912 Comm: syz-executor.5 Not tainted 6.4.0-rc3-syzkaller-00190-g0d85b27b0cc6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/16/2023
Fixes: 3a7d0d07a386 ("net: sched: extend Qdisc with rcu") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Vlad Buslov <vladbu@nvidia.com> Acked-by: Jamal Hadi Salim<jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The originator of an SRH places the first hop's IPv6 address in the IPv6
header's IPv6 Destination Address and the second hop's IPv6 address as
the first address in Addresses[1..n].
The CmprI and CmprE fields indicate the number of prefix octets that are
shared with the IPv6 Destination Address. When CmprI or CmprE is not 0,
Addresses[1..n] are compressed as follows:
Segments Left indicates the number of route segments remaining. When the
value is not zero, the SRH is forwarded to the next hop. Its address
is extracted from Addresses[n - Segment Left + 1] and swapped with IPv6
Destination Address.
When Segment Left is greater than or equal to 2, the size of SRH is not
changed because Addresses[1..n-1] are decompressed and recompressed with
CmprI.
OTOH, when Segment Left changes from 1 to 0, the new SRH could have a
different size because Addresses[1..n-1] are decompressed with CmprI and
recompressed with CmprE.
Let's say CmprI is 15 and CmprE is 0. When we receive SRH with Segment
Left >= 2, Addresses[1..n-1] have 1 byte for each, and Addresses[n] has
16 bytes. When Segment Left is 1, Addresses[1..n-1] is decompressed to
16 bytes and not recompressed. Finally, the new SRH will need more room
in the header, and the size is (16 - 1) * (n - 1) bytes.
Here the max value of n is 255 as Segment Left is u8, so in the worst case,
we have to allocate 3825 bytes in the skb headroom. However, now we only
allocate a small fixed buffer that is IPV6_RPL_SRH_WORST_SWAP_SIZE (16 + 7
bytes). If the decompressed size overflows the room, skb_push() hits BUG()
below [0].
Instead of allocating the fixed buffer for every packet, let's allocate
enough headroom only when we receive SRH with Segment Left 1.
Fixes: 8610c7c6e3bd ("net: ipv6: add support for rpl sr exthdr") Reported-by: Max VA Closes: https://www.interruptlabs.co.uk/articles/linux-ipv6-route-of-death Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20230605180617.67284-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm sched entity must be flushed before finishing, to account for
jobs potentially still in flight at that time.
Lima did not do this flush until now, so switch the destroy call to the
drm_sched_entity_destroy() wrapper which will take care of that.
This fixes a regression on lima which started since the rework in
commit 2fdb8a8f07c2 ("drm/scheduler: rework entity flush, kill and fini")
where some specific types of applications may hang indefinitely.
syzkaller found a repro that causes Hung Task [0] with ipset. The repro
first creates an ipset and then tries to delete a large number of IPs
from the ipset concurrently:
The first deleting thread hogs a CPU with nfnl_lock(NFNL_SUBSYS_IPSET)
held, and other threads wait for it to be released.
Previously, the same issue existed in set->variant->uadt() that could run
so long under ip_set_lock(set). Commit 5e29dc36bd5e ("netfilter: ipset:
Rework long task execution when adding/deleting entries") tried to fix it,
but the issue still exists in the caller with another mutex.
While adding/deleting many IPs, we should release the CPU periodically to
prevent someone from abusing ipset to hang the system.
Note we need to increment the ipset's refcnt to prevent the ipset from
being destroyed while rescheduling.
An nf_conntrack_helper from nf_conn_help may become NULL after DNAT.
Observed when TCP port 1720 (Q931_PORT), associated with h323 conntrack
helper, is DNAT'ed to another destination port (e.g. 1730), while
nfqueue is being used for final acceptance (e.g. snort).
This happenned after transition from kernel 4.14 to 5.10.161.
Workarounds:
* keep the same port (1720) in DNAT
* disable nfqueue
* disable/unload h323 NAT helper
At the end of `nft_bitwise_reduce`, there is a loop which is intended to
update the bitwise expression associated with each tracked destination
register. However, currently, it just updates the first register
repeatedly. Fix it.
Fixes: 34cc9e52884a ("netfilter: nf_tables: cancel tracking for clobbered destination registers") Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In net/netlink/af_netlink.c, function netlink_getsockopt(), for NETLINK_LIST_MEMBERSHIPS,
nlk->ngroups equals to 36. Before Commit f4e4534850a9, the optlen is calculated as
ALIGN(nlk->ngroups / 8, sizeof(u32)) = 4
After that commit, the optlen is
ALIGN(BITS_TO_BYTES(nlk->ngroups), sizeof(u32)) = 8
Fix the test by setting the expected optlen to be 8.
This should use wiphy_lock() now instead of acquiring the
RTNL, since cfg80211_stop_sched_scan_req() now needs that.
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use DMA_RESV_USAGE_BOOKKEEP reservation for buffer objects, except for
command buffers for which we use DMA_RESV_USAGE_WRITE (since VPU can
write to command buffer context save area).
Drivers that use the gen_pool*() family of functions should
select GENERIC_ALLOCATOR to prevent build errors like these:
ld: drivers/accel/ivpu/ivpu_ipc.o: in function `gen_pool_free':
include/linux/genalloc.h:172: undefined reference to `gen_pool_free_owner'
ld: drivers/accel/ivpu/ivpu_ipc.o: in function `gen_pool_alloc_algo':
include/linux/genalloc.h:138: undefined reference to `gen_pool_alloc_algo_owner'
ld: drivers/accel/ivpu/ivpu_ipc.o: in function `gen_pool_free':
include/linux/genalloc.h:172: undefined reference to `gen_pool_free_owner'
ld: drivers/accel/ivpu/ivpu_ipc.o: in function `ivpu_ipc_init':
drivers/accel/ivpu/ivpu_ipc.c:441: undefined reference to `devm_gen_pool_create'
ld: drivers/accel/ivpu/ivpu_ipc.o: in function `gen_pool_add_virt':
include/linux/genalloc.h:104: undefined reference to `gen_pool_add_owner'
Fixes: 5d7422cfb498 ("accel/ivpu: Add IPC driver and JSM messages") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/all/202305221206.1TaugDKP-lkp@intel.com/ Cc: Oded Gabbay <ogabbay@kernel.org> Cc: dri-devel@lists.freedesktop.org Cc: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Cc: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Cc: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com> Cc: Krystian Pradzynski <krystian.pradzynski@linux.intel.com> Cc: Jeffrey Hugo <quic_jhugo@quicinc.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230526044519.13441-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Statistics read through bond interface via sysfs causes
below bug and traces as it triggers the bonding module to
collect the slave device statistics while holding the spinlock,
beneath that qede->qed driver statistics flow gets scheduled out
due to usleep_range() used in PTT acquire logic
Fix this by collecting the statistics asynchronously from a periodic
delayed work scheduled at default stats coalescing interval and return
the recent copy of statisitcs from .ndo_get_stats64(), also add ability
to configure/retrieve stats coalescing interval using below commands -
Don't do link address translation for beacons and probe responses,
this leads to reporting multiple scan list entries for the same AP
(one with the MLD address) which just breaks things.
We might need to extend this in the future for some other (action)
frames that aren't MLD addressed.
There were two bugs when creating the non-inheritence
element:
1) 'at_extension' needs to be declared outside the loop,
otherwise the value resets every iteration and we
can never really switch properly
2) 'added' never got set to true, so we always cut off
the extension element again at the end of the function
This shows another issue that we might add a list but no
extension list, but we need to make the extension list a
zero-length one in that case.
Fix all these issues. While at it, add a comment explaining
the trim.
Fixes: 81151ce462e5 ("wifi: mac80211: support MLO authentication/association with one link") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20230604120651.3addaa5c4782.If3a78f9305997ad7ef4ba7ffc17a8234c956f613@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receiving a connect response we should make sure that the DCID is
within the valid range and that we don't already have another channel
allocated for the same DCID.
Missing checks may violate the specification (BLUETOOTH CORE SPECIFICATION
Version 5.4 | Vol 3, Part A, Page 1046).
Fixes: 40624183c202 ("Bluetooth: L2CAP: Add missing checks for invalid LE DCID") Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The order of CIS handle array in Set CIG Parameters response shall match
the order of the CIS_ID array in the command (Core v5.3 Vol 4 Part E Sec
7.8.97). We send CIS_IDs mainly in the order of increasing CIS_ID (but
with "last" CIS first if it has fixed CIG_ID). In handling of the
reply, we currently assume this is also the same as the order of
hci_conn in hdev->conn_hash, but that is not true.
Match the correct hci_conn to the correct handle by matching them based
on the CIG+CIS combination. The CIG+CIS combination shall be unique for
ISO_LINK hci_conn at state >= BT_BOUND, which we maintain in
hci_le_set_cig_params.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log