Stephan Gerhold [Fri, 18 Jun 2021 17:36:10 +0000 (19:36 +0200)]
net: wwan: Add RPMSG WWAN CTRL driver
The remote processor messaging (rpmsg) subsystem provides an interface
to communicate with other remote processors. On many Qualcomm SoCs this
is used to communicate with an integrated modem DSP that implements most
of the modem functionality and provides high-level protocols like
QMI or AT to allow controlling the modem.
For QMI, most older Qualcomm SoCs (e.g. MSM8916/MSM8974) have
a standalone "DATA5_CNTL" channel that allows exchanging QMI messages.
Note that newer SoCs (e.g. SDM845) only allow exchanging QMI messages
via a shared QRTR channel that is available via a socket API on Linux.
For AT, the "DATA4" channel accepts at least a limited set of AT
commands, on many older and newer Qualcomm SoCs, although QMI is
typically the preferred control protocol.
Often there are additional QMI/AT channels (usually named DATA*_CNTL
for QMI and DATA* for AT), but it is not clear if those are really
functional on all devices. Also, at the moment there is no use case
for having multiple QMI/AT ports. If needed more channels could be
added later after more testing.
Note that the data path (network interface) is entirely separate
from the control path and varies between Qualcomm SoCs, e.g. "IPA"
on newer Qualcomm SoCs or "BAM-DMUX" on some older ones.
The RPMSG WWAN CTRL driver exposes the QMI/AT control ports via the
WWAN subsystem, and therefore allows userspace like ModemManager to
set up the modem. Until now, ModemManager had to use the RPMSG-specific
rpmsg-char where the channels must be explicitly exposed as a char
device first and don't show up directly in sysfs.
The driver is a fairly simple glue layer between WWAN and RPMSG
and is mostly based on the existing mhi_wwan_ctrl.c and rpmsg_char.c.
Cc: Loic Poulain <loic.poulain@linaro.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephan Gerhold [Fri, 18 Jun 2021 17:36:09 +0000 (19:36 +0200)]
rpmsg: core: Add driver_data for rpmsg_device_id
Most device_id structs provide a driver_data field that can be used
by drivers to associate data more easily for a particular device ID.
Add the same for the rpmsg_device_id.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Jun 2021 20:10:36 +0000 (13:10 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Jesse Brandeburg says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-18
Update three of the Intel Ethernet drivers with similar (but not the
same) improvements to simplify the packet type table init, while removing
an unused structure entry. For the ice driver, the table is extended
to 10 bits, which is the hardware limit, and for now is initialized
to zero.
The end result is slightly reduced memory usage, removal of a bunch
of code, and more specific initialization.
====================
When memcpy_to_msg() fails in virtio_transport_seqpacket_do_dequeue(),
we already set `dequeued_len` with the negative error value returned
by memcpy_to_msg().
So we can directly check `dequeued_len` value instead of using a
dedicated flag variable to skip the copy path for the rest of
fragments.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Fri, 18 Jun 2021 13:35:25 +0000 (15:35 +0200)]
vsock: rename vsock_wait_data()
vsock_wait_data() is used only by STREAM and SEQPACKET sockets,
so let's rename it to vsock_connectible_wait_data(), using the same
nomenclature (connectible) used in other functions after the
introduction of SEQPACKET.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Fri, 18 Jun 2021 13:35:24 +0000 (15:35 +0200)]
vsock: rename vsock_has_data()
vsock_has_data() is used only by STREAM and SEQPACKET sockets,
so let's rename it to vsock_connectible_has_data(), using the same
nomenclature (connectible) used in other functions after the
introduction of SEQPACKET.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 18 Jun 2021 13:48:12 +0000 (16:48 +0300)]
net: dsa: sja1105: completely error out in sja1105_static_config_reload if something fails
If reloading the static config fails for whatever reason, for example if
sja1105_static_config_check_valid() fails, then we "goto out_unlock_ptp"
but we print anyway that "Reset switch and programmed static config.",
which is confusing because we didn't. We also do a bunch of other stuff
like reprogram the XPCS and reload the credit-based shapers, as if a
switch reset took place, which didn't.
So just unlock the PTP lock and goto out, skipping all of that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 18 Jun 2021 13:44:00 +0000 (16:44 +0300)]
net: dsa: sja1105: allow the TTEthernet configuration in the static config for SJA1110
Currently sja1105_static_config_check_valid() is coded up to detect
whether TTEthernet is supported based on device ID, and this check was
not updated to cover SJA1110.
However, it is desirable to have as few checks for the device ID as
possible, so the driver core is more generic. So what we can do is look
at the static config table operations implemented by that specific
switch family (populated by sja1105_static_config_init) whether the
schedule table has a non-zero maximum entry count (meaning that it is
supported) or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Fri, 18 Jun 2021 12:09:45 +0000 (20:09 +0800)]
net: hns3: fix reuse conflict of the rx page
In the current rx page reuse handling process, the rx page buffer may
have conflict between driver and stack in high-pressure scenario.
To fix this problem, we need to check whether the page is only owned
by driver at the begin and at the end of a page to make sure there is
no reuse conflict between driver and stack when desc_cb->page_offset
is rollbacked to zero or increased.
Fixes: fa7711b888f2 ("net: hns3: optimize the rx page reuse handling process") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 18 Jun 2021 11:52:54 +0000 (14:52 +0300)]
net: dsa: sja1105: properly power down the microcontroller clock for SJA1110
It turns out that powering down the BASE_TIMER_CLK does not turn off the
microcontroller, just its timers, including the one for the watchdog.
So the embedded microcontroller is still running, and potentially still
doing things.
To prevent unwanted interference, we should power down the BASE_MCSS_CLK
as well (MCSS = microcontroller subsystem).
The trouble is that currently we turn off the BASE_TIMER_CLK for SJA1110
from the .clocking_setup() method, mostly because this is a Clock
Generation Unit (CGU) setting which was traditionally configured in that
method for SJA1105. But in SJA1105, the CGU was used for bringing up the
port clocks at the proper speeds, and in SJA1110 it's not (but rather
for initial configuration), so it's best that we rebrand the
sja1110_clocking_setup() method into what it really is - an implementation
of the .disable_microcontroller() method.
Since disabling the microcontroller only needs to be done once, at probe
time, we can choose the best place to do that as being in sja1105_setup(),
before we upload the static config to the device. This guarantees that
the static config being used by the switch afterwards is really ours.
Note that the procedure to upload a static config necessarily resets the
switch. This already did not reset the microcontroller, only the switch
core, so since the .disable_microcontroller() method is guaranteed to be
called by that point, if it's disabled, it remains disabled. Add a
comment to make that clear.
With the code movement for SJA1110 from .clocking_setup() to
.disable_microcontroller(), both methods are optional and are guarded by
"if" conditions.
Tested by enabling in the device tree the rev-mii switch port 0 that
goes towards the microcontroller, and flashing a firmware that would
have networking. Without this patch, the microcontroller can be pinged,
with this patch it cannot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 18 Jun 2021 10:19:19 +0000 (11:19 +0100)]
qlcnic: remove redundant continue statement
The continue statement at the end of a for-loop has no effect,
it is redundant and can be removed.
Addresses-Coverity: ("Continue has no effect") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 18 Jun 2021 10:01:55 +0000 (11:01 +0100)]
net: bridge: remove redundant continue statement
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Addresses-Coverity: ("Continue has no effect") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 18 Jun 2021 09:44:25 +0000 (10:44 +0100)]
net: stmmac: remove redundant continue statement
The continue statement in the for-loop has no effect, remove it.
Addresses-Coverity: ("Continue has no effect") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Machek [Fri, 18 Jun 2021 09:35:26 +0000 (11:35 +0200)]
net: pxa168_eth: Fix a potential data race in pxa168_eth_remove
Commit 0571a753cb07 cancelled delayed work too late, keeping small
race. Cancel work sooner to close it completely.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de> Fixes: 0571a753cb07 ("net: pxa168_eth: Fix a potential data race in pxa168_eth_remove") Signed-off-by: David S. Miller <davem@davemloft.net>
Qing Zhang [Fri, 18 Jun 2021 02:53:34 +0000 (10:53 +0800)]
stmmac: pci: Add dwmac support for Loongson
This GMAC module is integrated into the Loongson-2K SoC and the LS7A
bridge chip.
Signed-off-by: Qing Zhang <zhangqing@loongson.cn> Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Jun 2021 18:40:12 +0000 (11:40 -0700)]
Merge branch 'mptcp-dss-checksums'
Mat Martineau says:
====================
mptcp: DSS checksum support
RFC 8684 defines a DSS checksum feature that allows MPTCP to detect
middlebox interference with the MPTCP DSS header and the portion of the
data stream associated with that header. So far, the MPTCP
implementation in the Linux kernel has not supported this feature.
This patch series adds DSS checksum support. By default, the kernel will
not request checksums when sending SYN or SYN/ACK packets for MPTCP
connections. Outgoing checksum requests can be enabled with a
per-namespace net.mptcp.checksum_enabled sysctl. MPTCP connections will
now proceed with DSS checksums when the peer requests them, whether the
sysctl is enabled or not.
Patches 1-5 add checksum bits to the outgoing SYN, SYN/ACK, and data
packet headers. This includes calculating the checksum using a range of
data and the MPTCP DSS mapping for that data.
Patches 6-10 handle the checksum request in the SYN or SYN/ACK, and
receiving and verifying the DSS checksum on data packets.
Patch 11 adjusts the MPTCP-level retransmission process for checksum
compatibility.
Patches 12-14 add checksum-related MIBs, the net.mptcp.checksum_enabled
sysctl, and a checksum field to debug trace output.
Patches 15 & 16 add selftests.
The series is slightly longer than the preferred 15-patch limit that
patchwork warns about. I do try to stay below that whenever possible -
this series does implement one feature and is, I think, cohesive enough
to justify keeping it together. If it's at all problematic please let me
know!
A trivial merge conflict with net/master is introduced in patch 15: a
commit in net/master removes a couple of nearby lines of code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:22 +0000 (16:46 -0700)]
selftests: mptcp: enable checksum in mptcp_join.sh
This patch added a new argument "-C" for the mptcp_join.sh script to set
the sysctl checksum_enabled to 1 in ns1 and ns2 to enable the data
checksum.
In chk_join_nr, check the counter of the mib for the data checksum.
Also added a new argument "-S" for the mptcp_join.sh script to start the
test cases that verify the checksum handshake:
* Sender and listener both have checksums off
* Sender and listener both have checksums on
* Sender checksums off, listener checksums on
* Sender checksums on, listener checksums off
The output looks like this:
01 checksum test 0 0 sum[ ok ] - csum [ ok ]
02 checksum test 1 1 sum[ ok ] - csum [ ok ]
03 checksum test 0 1 sum[ ok ] - csum [ ok ]
04 checksum test 1 0 sum[ ok ] - csum [ ok ]
05 no JOIN syn[ ok ] - synack[ ok ] - ack[ ok ]
sum[ ok ] - csum [ ok ]
06 single subflow, limited by client syn[ ok ] - synack[ ok ] - ack[ ok ]
sum[ ok ] - csum [ ok ]
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:21 +0000 (16:46 -0700)]
selftests: mptcp: enable checksum in mptcp_connect.sh
This patch added a new argument "-C" for the mptcp_connect.sh script to
set the sysctl checksum_enabled to 1 in ns1, ns2, ns3 and ns4 to enable
the data checksum.
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:20 +0000 (16:46 -0700)]
mptcp: dump csum fields in mptcp_dump_mpext
In mptcp_dump_mpext, dump the csum fields, csum and csum_reqd in struct
mptcp_dump_mpext too.
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:19 +0000 (16:46 -0700)]
mptcp: add a new sysctl checksum_enabled
This patch added a new sysctl, named checksum_enabled, to control
whether DSS checksum can be enabled.
Acked-by: Paolo Abeni <pabeni@redhat.com> Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:18 +0000 (16:46 -0700)]
mptcp: add the mib for data checksum
This patch added the mib for the data checksum, MPTCP_MIB_DATACSUMERR.
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 17 Jun 2021 23:46:17 +0000 (16:46 -0700)]
mptcp: tune re-injections for csum enabled mode
If the MPTCP-level checksum is enabled, on re-injections we
must spool a complete DSS, or the receive side will not be
able to compute the csum and process any data.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 17 Jun 2021 23:46:16 +0000 (16:46 -0700)]
mptcp: validate the data checksum
This patch added three new members named data_csum, csum_len and
map_csum in struct mptcp_subflow_context, implemented a new function
named mptcp_validate_data_checksum().
If the current mapping is valid and csum is enabled traverse the later
pending skbs and compute csum incrementally till the whole mapping has
been covered. If not enough data is available in the rx queue, return
MAPPING_EMPTY - that is, no data.
Next subflow_data_ready invocation will trigger again csum computation.
When the full DSS is available, validate the csum and return to the
caller an appropriate error code, to trigger subflow reset of fallback
as required by the RFC.
Additionally:
- if the csum prevence in the DSS don't match the negotiated value e.g.
csum present, but not requested, return invalid mapping to trigger
subflow reset.
- keep some csum state, to avoid re-compute the csum on the same data
when multiple rx queue traversal are required.
- clean-up the uncompleted mapping from the receive queue on close, to
allow proper subflow disposal
Co-developed-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:15 +0000 (16:46 -0700)]
mptcp: receive checksum for DSS
In mptcp_parse_option, adjust the expected_opsize, and always parse the
data checksum value from the receiving DSS regardless of csum presence.
Then save it in mp_opt->csum.
Co-developed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:14 +0000 (16:46 -0700)]
mptcp: receive checksum for MP_CAPABLE with data
This patch added a new member named csum in struct mptcp_options_received.
When parsing the MP_CAPABLE with data, if the checksum is enabled,
adjust the expected_opsize. If the receiving option length matches the
length with the data checksum, get the checksum value and save it in
mp_opt->csum. And in mptcp_incoming_options, pass it to mpext->csum.
We always parse any csum/nocsum combination and delay the presence check
to later code, to allow reset if missing.
Additionally, in the TX path, use the newly introduce ext field to avoid
MPTCP csum recomputation on TCP retransmission and unneeded csum update
on when setting the data fin_flag.
Co-developed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:13 +0000 (16:46 -0700)]
mptcp: add csum_reqd in mptcp_options_received
This patch added a new flag csum_reqd in struct mptcp_options_received, if
the flag MPTCP_CAP_CHECKSUM_REQD is set in the receiving MP_CAPABLE
suboption, set this flag.
In mptcp_sk_clone and subflow_finish_connect, if the csum_reqd flag is set,
enable the msk->csum_enabled flag.
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:12 +0000 (16:46 -0700)]
mptcp: add sk parameter for mptcp_get_options
This patch added a new parameter name sk in mptcp_get_options().
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:11 +0000 (16:46 -0700)]
mptcp: send out checksum for DSS
In mptcp_write_options, if the checksum is enabled, adjust the option
length and send out the data checksum with DSS suboption.
Co-developed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:10 +0000 (16:46 -0700)]
mptcp: send out checksum for MP_CAPABLE with data
If the checksum is enabled, send out the data checksum with the
MP_CAPABLE suboption with data.
In mptcp_established_options_mp, save the data checksum in
opts->ext_copy.csum. In mptcp_write_options, adjust the option length and
send it out with the MP_CAPABLE suboption.
Co-developed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:09 +0000 (16:46 -0700)]
mptcp: add csum_reqd in mptcp_out_options
This patch added a new member csum_reqd in struct mptcp_out_options and
struct mptcp_subflow_request_sock. Initialized it with the helper
function mptcp_is_checksum_enabled().
In mptcp_write_options, if this field is enabled, send out the MP_CAPABLE
suboption with the MPTCP_CAP_CHECKSUM_REQD flag.
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:08 +0000 (16:46 -0700)]
mptcp: generate the data checksum
This patch added a new member named csum in struct mptcp_ext, implemented
a new function named mptcp_generate_data_checksum().
Generate the data checksum in mptcp_sendmsg_frag, save it in mpext->csum.
Note that we must generate the csum for zero window probe, too.
Do the csum update incrementally, to avoid multiple csum computation
when the data is appended to existing skb.
Note that in a later patch we will skip unneeded csum related operation.
Changes not included here to keep the delta small.
Co-developed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Thu, 17 Jun 2021 23:46:07 +0000 (16:46 -0700)]
mptcp: add csum_enabled in mptcp_sock
This patch added a new member named csum_enabled in struct mptcp_sock,
used a dummy mptcp_is_checksum_enabled() helper to initialize it.
Also added a new member named mptcpi_csum_enabled in struct mptcp_info
to expose the csum_enabled flag.
Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Jun 2021 18:35:47 +0000 (11:35 -0700)]
Merge branch 'seg6.end.dt6'
Andrea Mayer says:
====================
seg6: add support for SRv6 End.DT46 Behavior
SRv6 End.DT46 Behavior is defined in the IETF RFC 8986 [1] along with SRv6
End.DT4 and End.DT6 Behaviors.
The proposed End.DT46 implementation is meant to support the decapsulation
of both IPv4 and IPv6 traffic coming from a *single* SRv6 tunnel.
The SRv6 End.DT46 Behavior greatly simplifies the setup and operations of
SRv6 VPNs in the Linux kernel.
- patch 1/2 is the core patch that adds support for the SRv6 End.DT46
Behavior;
- patch 2/2 adds the selftest for SRv6 End.DT46 Behavior.
The patch introducing the new SRv6 End.DT46 Behavior in iproute2 will
follow shortly.
Comments, suggestions and improvements are very welcome as always!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Mayer [Thu, 17 Jun 2021 17:16:45 +0000 (19:16 +0200)]
selftests: seg6: add selftest for SRv6 End.DT46 Behavior
this selftest is designed for evaluating the new SRv6 End.DT46 Behavior
used, in this example, for implementing IPv4/IPv6 L3 VPN use cases.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: Paolo Lungaroni <paolo.lungaroni@uniroma2.it> Acked-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Mayer [Thu, 17 Jun 2021 17:16:44 +0000 (19:16 +0200)]
seg6: add support for SRv6 End.DT46 Behavior
IETF RFC 8986 [1] includes the definition of SRv6 End.DT4, End.DT6, and
End.DT46 Behaviors.
The current SRv6 code in the Linux kernel only implements End.DT4 and
End.DT6 which can be used respectively to support IPv4-in-IPv6 and
IPv6-in-IPv6 VPNs. With End.DT4 and End.DT6 it is not possible to create a
single SRv6 VPN tunnel to carry both IPv4 and IPv6 traffic.
The proposed End.DT46 implementation is meant to support the decapsulation
of IPv4 and IPv6 traffic coming from a single SRv6 tunnel.
The implementation of the SRv6 End.DT46 Behavior in the Linux kernel
greatly simplifies the setup and operations of SRv6 VPNs.
The SRv6 End.DT46 Behavior leverages the infrastructure of SRv6 End.DT{4,6}
Behaviors implemented so far, because it makes use of a VRF device in
order to force the routing lookup into the associated routing table.
To make the End.DT46 work properly, it must be guaranteed that the routing
table used for routing lookup operations is bound to one and only one VRF
during the tunnel creation. Such constraint has to be enforced by enabling
the VRF strict_mode sysctl parameter, i.e.:
$ sysctl -wq net.vrf.strict_mode=1
Note that the same approach is used for the SRv6 End.DT4 Behavior and for
the End.DT6 Behavior in VRF mode.
The command used to instantiate an SRv6 End.DT46 Behavior is
straightforward, i.e.:
$ ip -6 route add 2001:db8::1 encap seg6local action End.DT46 vrftable 100 dev vrf100.
Performance and impact of SRv6 End.DT46 Behavior on the SRv6 Networking
=======================================================================
This patch aims to add the SRv6 End.DT46 Behavior with minimal impact on
the performance of SRv6 End.DT4 and End.DT6 Behaviors.
In order to verify this, we tested the performance of the newly introduced
SRv6 End.DT46 Behavior and compared it with the performance of SRv6
End.DT{4,6} Behaviors, considering both the patched kernel and the kernel
before applying the End.DT46 patch (referred to as vanilla kernel).
In details, the following decapsulation scenarios were considered:
1.a) IPv6 traffic in SRv6 End.DT46 Behavior on patched kernel;
1.b) IPv4 traffic in SRv6 End.DT46 Behavior on patched kernel;
2.a) SRv6 End.DT6 Behavior (VRF mode) on patched kernel;
2.b) SRv6 End.DT4 Behavior on patched kernel;
3.a) SRv6 End.DT6 Behavior (VRF mode) on vanilla kernel (without the
End.DT46 patch);
3.b) SRv6 End.DT4 Behavior on vanilla kernel (without the End.DT46 patch).
All tests were performed on a testbed deployed on the CloudLab [2]
facilities. We considered IPv{4,6} traffic handled by a single core (at 2.4
GHz on a Xeon(R) CPU E5-2630 v3) on kernel 5.13-rc1 using packets of size
~ 100 bytes.
Scenario (1.a): average 684.70 kpps; std. dev. 0.7 kpps;
Scenario (1.b): average 711.69 kpps; std. dev. 1.2 kpps;
Scenario (2.a): average 690.70 kpps; std. dev. 1.2 kpps;
Scenario (2.b): average 722.22 kpps; std. dev. 1.7 kpps;
Scenario (3.a): average 690.02 kpps; std. dev. 2.6 kpps;
Scenario (3.b): average 721.91 kpps; std. dev. 1.2 kpps;
Considering the results for the patched kernel (1.a, 1.b, 2.a, 2.b) we
observe that the performance degradation incurred in using End.DT46 rather
than End.DT6 and End.DT4 respectively for IPv6 and IPv4 traffic is minimal,
around 0.9% and 1.5%. Such very minimal performance degradation is the
price to be paid if one prefers to use a single tunnel capable of handling
both types of traffic (IPv4 and IPv6).
Comparing the results for End.DT4 and End.DT6 under the patched and the
vanilla kernel (2.a, 2.b, 3.a, 3.b) we observe that the introduction of the
End.DT46 patch has no impact on the performance of End.DT4 and End.DT6.
[2] https://www.cloudlab.us
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_trap tests for the netdevsim fail due to misspelled
debugfs file name. Change this name, as well as name of callback
function, to match the naming as in the devlink itself - 'trap_drop_counter'.
Test-results:
selftests: drivers/net/netdevsim: devlink_trap.sh
TEST: Initialization [ OK ]
TEST: Trap action [ OK ]
TEST: Trap metadata [ OK ]
TEST: Non-existing trap [ OK ]
TEST: Non-existing trap action [ OK ]
TEST: Trap statistics [ OK ]
TEST: Trap group action [ OK ]
TEST: Non-existing trap group [ OK ]
TEST: Trap group statistics [ OK ]
TEST: Trap policer [ OK ]
TEST: Trap policer binding [ OK ]
TEST: Port delete [ OK ]
TEST: Device delete [ OK ]
Fixes: a7b3527a43fe ("drivers: net: netdevsim: add devlink trap_drop_counter_get implementation") Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Tue, 23 Feb 2021 23:47:07 +0000 (15:47 -0800)]
iavf: clean up packet type lookup table
Remove the unused ptype struct value, which makes table init easier for
the zero entries, and use ranged initializer to remove a bunch of code
(works with gcc and clang). There is no significant functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jesse Brandeburg [Tue, 23 Feb 2021 23:47:06 +0000 (15:47 -0800)]
i40e: clean up packet type lookup table
Remove the unused ptype struct value, which makes table init easier for
the zero entries, and use ranged initializer to remove a bunch of code
(works with gcc and clang). There is no significant functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jesse Brandeburg [Tue, 23 Feb 2021 23:47:05 +0000 (15:47 -0800)]
ice: report hash type such as L2/L3/L4
The hardware is reporting the type of the hash used for RSS
as a PTYPE field in the receive descriptor. Use this value to set
the skb packet hash type by extending the hash type table to
cover all 10-bits of possible values (requiring some variables
to be changed from u8 to u16), and then use that table to convert
to one of the possible values in enum pkt_hash_types.
While we're here, remove the unused ptype struct value, which
makes table init easier for the zero entries, and use ranged
initializer to remove a bunch of code (works with gcc and clang).
Without this change, the kernel will recalculate the hash in software,
which can consume extra CPU cycles.
Co-developed-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Peng Li [Thu, 17 Jun 2021 14:03:19 +0000 (22:03 +0800)]
net: hdlc_ppp: add required space
Add space required after that ','.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 17 Jun 2021 14:03:18 +0000 (22:03 +0800)]
net: hdlc_ppp: remove unnecessary out of memory message
This patch removes unnecessary out of memory message,
to fix the following checkpatch.pl warning:
"WARNING: Possible unnecessary 'out of memory' message"
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 17 Jun 2021 14:03:17 +0000 (22:03 +0800)]
net: hdlc_ppp: move out assignment in if condition
Should not use assignment in if condition.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 17 Jun 2021 14:03:16 +0000 (22:03 +0800)]
net: hdlc_ppp: fix the code style issue about "foo* bar"
Fix the checkpatch error as "foo* bar" or "foo*bar" should be "foo *bar".
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 17 Jun 2021 14:03:15 +0000 (22:03 +0800)]
net: hdlc_ppp: add blank line after declarations
This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Thu, 17 Jun 2021 14:03:14 +0000 (22:03 +0800)]
net: hdlc_ppp: remove redundant blank lines
This patch removes some redundant blank lines.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 17 Jun 2021 19:06:53 +0000 (12:06 -0700)]
Merge branch 'mdio-nodes'
Ioana Ciornei says:
====================
net: mdio: setup both fwnode and of_node
The first patch in this series fixes a bug introduced by mistake in the
previous ACPI MDIO patch set.
The next two patches are adding a new helper which takes a device and a
fwnode_handle and populates both the of_node and fwnode so that we make
sure that a bug like this does not happen anymore.
Also, the new helper is used in the MDIO area.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Thu, 17 Jun 2021 12:29:04 +0000 (15:29 +0300)]
driver core: add a helper to setup both the of_node and fwnode of a device
There are many places where both the fwnode_handle and the of_node of a
device need to be populated. Add a function which does both so that we
have consistency.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Thu, 17 Jun 2021 12:29:03 +0000 (15:29 +0300)]
net: mdio: setup of_node for the MDIO device
By mistake, the of_node of the MDIO device was not setup in the patch
linked below. As a consequence, any PHY driver that depends on the
of_node in its probe callback was not be able to successfully finish its
probe on a PHY, thus the Generic PHY driver was used instead.
Fix this by actually setting up the of_node.
Fixes: bc1bee3b87ee ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang [Thu, 17 Jun 2021 10:00:15 +0000 (18:00 +0800)]
r8152: store the information of the pipes
Store the information of the pipes to avoid calling usb_rcvctrlpipe(),
usb_sndctrlpipe(), usb_rcvbulkpipe(), usb_sndbulkpipe(), and
usb_rcvintpipe() frequently.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 25 day(s) which contain
a total of 148 files changed, 4779 insertions(+), 1248 deletions(-).
The main changes are:
1) BPF infrastructure to migrate TCP child sockets from a listener to another
in the same reuseport group/map, from Kuniyuki Iwashima.
2) Add a provably sound, faster and more precise algorithm for tnum_mul() as
noted in https://arxiv.org/abs/2105.05398, from Harishankar Vishwanathan.
3) Streamline error reporting changes in libbpf as planned out in the
'libbpf: the road to v1.0' effort, from Andrii Nakryiko.
4) Add broadcast support to xdp_redirect_map(), from Hangbin Liu.
5) Extends bpf_map_lookup_and_delete_elem() functionality to 4 more map
types, that is, {LRU_,PERCPU_,LRU_PERCPU_,}HASH, from Denis Salopek.
6) Support new LLVM relocations in libbpf to make them more linker friendly,
also add a doc to describe the BPF backend relocations, from Yonghong Song.
7) Silence long standing KUBSAN complaints on register-based shifts in
interpreter, from Daniel Borkmann and Eric Biggers.
8) Add dummy PT_REGS macros in libbpf to fail BPF program compilation when
target arch cannot be determined, from Lorenz Bauer.
9) Extend AF_XDP to support large umems with 1M+ pages, from Magnus Karlsson.
10) Fix two minor libbpf tc BPF API issues, from Kumar Kartikeya Dwivedi.
11) Move libbpf BPF_SEQ_PRINTF/BPF_SNPRINTF macros that can be used by BPF
programs to bpf_helpers.h header, from Florent Revest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 17 Jun 2021 18:39:48 +0000 (11:39 -0700)]
Merge branch 'gianfar-64-bit-stats'
Esben Haabendal says:
====================
net: gianfar: 64-bit statistics and rx_missed_errors counter
This series replaces the legacy 32-bit statistics to proper 64-bit ditto,
and implements rx_missed_errors counter on top of that.
The device supports a 16-bit RDRP counter, and a related carry bit and
interrupt, which allows implementation of a robust 64-bit counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Thu, 17 Jun 2021 09:49:28 +0000 (11:49 +0200)]
net: gianfar: Implement rx_missed_errors counter
Devices with RMON support has a 16-bit RDRP counter. It provides: "Receive
dropped packets counter. Increments for frames received which are streamed
to system but are later dropped due to lack of system resources."
To handle more than 2^16 dropped packets, a carry bit in CAR1 register is
set on overflow, so we enable irq when this is set, extending the counter
to 2^64 for handling situations where lots of packets are missed (e.g.
during heavy network storms).
Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Thu, 17 Jun 2021 09:49:15 +0000 (11:49 +0200)]
net: gianfar: Convert to ndo_get_stats64 interface
No reason to produce the legacy net_device_stats struct, only to have it
converted to rtnl_link_stats64. And as a bonus, this allows for improving
counter size to 64 bit.
Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Yingliang [Thu, 17 Jun 2021 08:02:07 +0000 (16:02 +0800)]
net: sched: fix error return code in tcf_del_walker()
When nla_put_u32() fails, 'ret' could be 0, it should
return error code in tcf_del_walker().
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Yingliang [Thu, 17 Jun 2021 05:11:19 +0000 (13:11 +0800)]
net: ipa: Add missing of_node_put() in ipa_firmware_load()
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. of_node_put() on it before exiting
this function.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 15 Jun 2021 13:52:53 +0000 (14:52 +0100)]
net: pcs: xpcs: Fix a less than zero u16 comparison error
Currently the check for the u16 variable val being less than zero is
always false because val is unsigned. Fix this by using the int
variable for the assignment and less than zero check.
Addresses-Coverity: ("Unsigned compared against 0") Fixes: f7380bba42fd ("net: pcs: xpcs: add support for NXP SJA1110") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 15 Jun 2021 14:28:47 +0000 (15:28 +0100)]
ice: remove redundant continue statement in a for-loop
The continue statement in the for-loop is redundant. Re-work the hw_lock
check to remove it.
Addresses-Coverity: ("Continue has no effect") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jacob Keller [Mon, 14 Jun 2021 16:59:16 +0000 (09:59 -0700)]
ice: remove unnecessary NULL checks before ptp_read_system_*
The ptp_read_system_prets and ptp_read_system_postts functions already
check for the NULL value of the ptp_system_timestamp structure pointer.
There is no need to check this manually in the ice driver code. Remove
the checks.
Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Paul M Stillwell Jr [Thu, 6 May 2021 15:40:08 +0000 (08:40 -0700)]
ice: remove local variable
Remove the local variable since it's only used once. Instead, use it
directly.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Paul M Stillwell Jr [Thu, 6 May 2021 15:40:07 +0000 (08:40 -0700)]
ice: reduce scope of variables
There are some places where the scope of a variable can
be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jacob Keller [Thu, 6 May 2021 15:40:05 +0000 (08:40 -0700)]
ice: mark PTYPE 2 as reserved
The entry for PTYPE 2 in the ice_ptype_lkup table incorrectly states
that this is an L2 packet with no payload. According to the datasheet,
this PTYPE is actually unused and reserved.
Fix the lookup entry to indicate this is an unused entry that is
reserved.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jacob Keller [Thu, 6 May 2021 15:40:04 +0000 (08:40 -0700)]
ice: fix incorrect payload indicator on PTYPE
The entry for PTYPE 90 indicates that the payload is layer 3. This does
not match the specification in the datasheet which indicates the packet
is a MAC, IPv6, UDP packet, with a payload in layer 4.
Fix the lookup table to match the data sheet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Andrii Nakryiko [Thu, 17 Jun 2021 04:14:46 +0000 (21:14 -0700)]
selftests/bpf: Fix selftests build with old system-wide headers
migrate_reuseport.c selftest relies on having TCP_FASTOPEN_CONNECT defined in
system-wide netinet/tcp.h. Selftests can use up-to-date uapi/linux/tcp.h, but
that one doesn't have SOL_TCP. So instead of switching everything to uapi
header, add #define for TCP_FASTOPEN_CONNECT to fix the build.
Fixes: c9d0bdef89a6 ("bpf: Test BPF_SK_REUSEPORT_SELECT_OR_MIGRATE.") Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp> Link: https://lore.kernel.org/bpf/20210617041446.425283-1-andrii@kernel.org
Daniel Borkmann [Wed, 16 Jun 2021 09:25:11 +0000 (11:25 +0200)]
bpf: Fix up register-based shifts in interpreter to silence KUBSAN
syzbot reported a shift-out-of-bounds that KUBSAN observed in the
interpreter:
[...]
UBSAN: shift-out-of-bounds in kernel/bpf/core.c:1420:2
shift exponent 255 is too large for 64-bit type 'long long unsigned int'
CPU: 1 PID: 11097 Comm: syz-executor.4 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:327
___bpf_prog_run.cold+0x19/0x56c kernel/bpf/core.c:1420
__bpf_prog_run32+0x8f/0xd0 kernel/bpf/core.c:1735
bpf_dispatcher_nop_func include/linux/bpf.h:644 [inline]
bpf_prog_run_pin_on_cpu include/linux/filter.h:624 [inline]
bpf_prog_run_clear_cb include/linux/filter.h:755 [inline]
run_filter+0x1a1/0x470 net/packet/af_packet.c:2031
packet_rcv+0x313/0x13e0 net/packet/af_packet.c:2104
dev_queue_xmit_nit+0x7c2/0xa90 net/core/dev.c:2387
xmit_one net/core/dev.c:3588 [inline]
dev_hard_start_xmit+0xad/0x920 net/core/dev.c:3609
__dev_queue_xmit+0x2121/0x2e00 net/core/dev.c:4182
__bpf_tx_skb net/core/filter.c:2116 [inline]
__bpf_redirect_no_mac net/core/filter.c:2141 [inline]
__bpf_redirect+0x548/0xc80 net/core/filter.c:2164
____bpf_clone_redirect net/core/filter.c:2448 [inline]
bpf_clone_redirect+0x2ae/0x420 net/core/filter.c:2420
___bpf_prog_run+0x34e1/0x77d0 kernel/bpf/core.c:1523
__bpf_prog_run512+0x99/0xe0 kernel/bpf/core.c:1737
bpf_dispatcher_nop_func include/linux/bpf.h:644 [inline]
bpf_test_run+0x3ed/0xc50 net/bpf/test_run.c:50
bpf_prog_test_run_skb+0xabc/0x1c50 net/bpf/test_run.c:582
bpf_prog_test_run kernel/bpf/syscall.c:3127 [inline]
__do_sys_bpf+0x1ea9/0x4f00 kernel/bpf/syscall.c:4406
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
[...]
Generally speaking, KUBSAN reports from the kernel should be fixed.
However, in case of BPF, this particular report caused concerns since
the large shift is not wrong from BPF point of view, just undefined.
In the verifier, K-based shifts that are >= {64,32} (depending on the
bitwidth of the instruction) are already rejected. The register-based
cases were not given their content might not be known at verification
time. Ideas such as verifier instruction rewrite with an additional
AND instruction for the source register were brought up, but regularly
rejected due to the additional runtime overhead they incur.
As Edward Cree rightly put it:
Shifts by more than insn bitness are legal in the BPF ISA; they are
implementation-defined behaviour [of the underlying architecture],
rather than UB, and have been made legal for performance reasons.
Each of the JIT backends compiles the BPF shift operations to machine
instructions which produce implementation-defined results in such a
case; the resulting contents of the register may be arbitrary but
program behaviour as a whole remains defined.
Guard checks in the fast path (i.e. affecting JITted code) will thus
not be accepted.
The case of division by zero is not truly analogous here, as division
instructions on many of the JIT-targeted architectures will raise a
machine exception / fault on division by zero, whereas (to the best
of my knowledge) none will do so on an out-of-bounds shift.
Given the KUBSAN report only affects the BPF interpreter, but not JITs,
one solution is to add the ANDs with 63 or 31 into ___bpf_prog_run().
That would make the shifts defined, and thus shuts up KUBSAN, and the
compiler would optimize out the AND on any CPU that interprets the shift
amounts modulo the width anyway (e.g., confirmed from disassembly that
on x86-64 and arm64 the generated interpreter code is the same before
and after this fix).
The BPF interpreter is slow path, and most likely compiled out anyway
as distros select BPF_JIT_ALWAYS_ON to avoid speculative execution of
BPF instructions by the interpreter. Given the main argument was to
avoid sacrificing performance, the fact that the AND is optimized away
from compiler for mainstream archs helps as well as a solution moving
forward. Also add a comment on LSH/RSH/ARSH translation for JIT authors
to provide guidance when they see the ___bpf_prog_run() interpreter
code and use it as a model for a new JIT backend.
Reported-by: syzbot+bed360704c521841c85d@syzkaller.appspotmail.com Reported-by: Kurt Manucredo <fuzzybritches0@gmail.com> Signed-off-by: Eric Biggers <ebiggers@kernel.org> Co-developed-by: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andrii@kernel.org> Tested-by: syzbot+bed360704c521841c85d@syzkaller.appspotmail.com Cc: Edward Cree <ecree.xilinx@gmail.com> Link: https://lore.kernel.org/bpf/0000000000008f912605bd30d5d7@google.com Link: https://lore.kernel.org/bpf/bac16d8d-c174-bdc4-91bd-bfa62b410190@gmail.com
Lorenz Bauer [Wed, 16 Jun 2021 08:36:35 +0000 (09:36 +0100)]
libbpf: Fail compilation if target arch is missing
bpf2go is the Go equivalent of libbpf skeleton. The convention is that
the compiled BPF is checked into the repository to facilitate distributing
BPF as part of Go packages. To make this portable, bpf2go by default
generates both bpfel and bpfeb variants of the C.
Using bpf_tracing.h is inherently non-portable since the fields of
struct pt_regs differ between platforms, so CO-RE can't help us here.
The only way of working around this is to compile for each target
platform independently. bpf2go can't do this by default since there
are too many platforms.
Define the various PT_... macros when no target can be determined and
turn them into compilation failures. This works because bpf2go always
compiles for bpf targets, so the compiler fallback doesn't kick in.
Conditionally define __BPF_MISSING_TARGET so that we can inject a
more appropriate error message at build time. The user can then
choose which platform to target explicitly.
projects / users / jedix / linux-maple.git / log