During NAT, a tuple collision may occur. When this happens, openvswitch
will make a second pass through NAT which will perform additional packet
modification. This will update the skb data, but not the flow key that
OVS uses. This means that future flow lookups, and packet matches will
have incorrect data. This has been supported since 5d50aa83e2c8 ("openvswitch: support asymmetric conntrack").
That commit failed to properly update the sw_flow_key attributes, since
it only called the ovs_ct_nat_update_key once, rather than each time
ovs_ct_nat_execute was called. As these two operations are linked, the
ovs_ct_nat_execute() function should always make sure that the
sw_flow_key is updated after a successful call through NAT infrastructure.
After recent fixes to ICMPv6 PTB handling we started dropping
PMTU updates higher than tp->mss_cache. Because of the stale
tp->mss_cache value PMTU updates during TFO are always dropped.
Thanks to Wei for helping zero in on the problem and the fix!
Fixes: c7bb4b89033b ("ipv6: tcp: drop silly ICMPv6 packet too big messages") Reported-by: Andre Nash <alnash@fb.com> Reported-by: Neil Spring <ntspring@fb.com> Reviewed-by: Wei Wang <weiwan@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220321165957.1769954-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC12 appears to be much smarter about its dependency tracking and is
aware that the relaxed variants are just normal loads and stores and
this is causing problems like:
The assumption when these were relaxed seems to be that device memory
would be mapped non reordering, and that other constructs
(spinlocks/etc) would provide the barriers to assure that packet data
and in memory rings/queues were ordered with respect to device
register reads/writes. This itself seems a bit sketchy, but the real
problem with GCC12 is that it is moving the actual reads/writes around
at will as though they were independent operations when in truth they
are not, but the compiler can't know that. When looking at the
assembly dumps for many of these routines its possible to see very
clean, but not strictly in program order operations occurring as the
compiler would be free to do if these weren't actually register
reads/write operations.
Its possible to suppress the timeout with a liberal bit of dma_mb()'s
sprinkled around but the device still seems unable to reliably
send/receive data. A better plan is to use the safer readl/writel
everywhere.
Since this partially reverts an older commit, which notes the use of
the relaxed variants for performance reasons. I would suggest that
any performance problems with this commit are targeted at relaxing only
the performance critical code paths after assuring proper barriers.
Fixes: 69d2ea9c79898 ("net: bcmgenet: Use correct I/O accessors") Reported-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Acked-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220310045358.224350-1-jeremy.linton@arm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some ATI SB600 USB adapters advertise MSI, but if INTx is disabled by
setting PCI_COMMAND_INTX_DISABLE, MSI doesn't work either. The PCI/PCIe
specs do not require software to set PCI_COMMAND_INTX_DISABLE when enabling
MSI, but Linux has done that for many years.
Mick reported that 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI
devices") broke these devices. Prior to 306c54d0edb6, they used INTx.
Starting with 306c54d0edb6, they use MSI, and and the fact that Linux sets
PCI_COMMAND_INTX_DISABLE means both INTx and MSI are disabled on these
devices.
Avoid this SB600 defect by disabling MSI so we use INTx as before.
When test_lirc_mode2_user exec failed, the test report failed but still
exit with 0. Fix it by exiting with an error code.
Another issue is for the LIRCDEV checking. With bash -n, we need to quote
the variable, or it will always be true. So if test_lirc_mode2_user was
not run, just exit with skip code.
Fixes: 6bdd533cee9a ("bpf: add selftest for lirc_mode2 type program") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220321024149.157861-1-liuhangbin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d44 ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'") Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa490 ("i2c: meson: set clock divider in probe instead of setting it for each transfer") Signed-off-by: Lucas Tanure <tanure@linux.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a netlink message is received, netlink_recvmsg() fills in the address
of the sender. One of the fields is the 32-bit bitfield nl_groups, which
carries the multicast group on which the message was received. The least
significant bit corresponds to group 1, and therefore the highest group
that the field can represent is 32. Above that, the UB sanitizer flags the
out-of-bounds shift attempts.
Which bits end up being set in such case is implementation defined, but
it's either going to be a wrong non-zero value, or zero, which is at least
not misleading. Make the latter choice deterministic by always setting to 0
for higher-numbered multicast groups.
To get information about membership in groups >= 32, userspace is expected
to use nl_pktinfo control messages[0], which are enabled by NETLINK_PKTINFO
socket option.
[0] https://lwn.net/Articles/147608/
The way to trigger this issue is e.g. through monitoring the BRVLAN group:
# bridge monitor vlan &
# ip link add name br type bridge
Which produces the following citation:
UBSAN: shift-out-of-bounds in net/netlink/af_netlink.c:162:19
shift exponent 32 is too large for 32-bit type 'int'
The PMTU update and ICMP redirect helper functions initialise their fl4
variable with either __build_flow_key() or build_sk_flow_key(). These
initialisation functions always set ->flowi4_scope with
RT_SCOPE_UNIVERSE and might set the ECN bits of ->flowi4_tos. This is
not a problem when the route lookup is later done via
ip_route_output_key_hash(), which properly clears the ECN bits from
->flowi4_tos and initialises ->flowi4_scope based on the RTO_ONLINK
flag. However, some helpers call fib_lookup() directly, without
sanitising the tos and scope fields, so the route lookup can fail and,
as a result, the ICMP redirect or PMTU update aren't taken into
account.
Fix this by extracting the ->flowi4_tos and ->flowi4_scope sanitisation
code into ip_rt_fix_tos(), then use this function in handlers that call
fib_lookup() directly.
Note 1: We can't sanitise ->flowi4_tos and ->flowi4_scope in a central
place (like __build_flow_key() or flowi4_init_output()), because
ip_route_output_key_hash() expects non-sanitised values. When called
with sanitised values, it can erroneously overwrite RT_SCOPE_LINK with
RT_SCOPE_UNIVERSE in ->flowi4_scope. Therefore we have to be careful to
sanitise the values only for those paths that don't call
ip_route_output_key_hash().
Note 2: The problem is mostly about sanitising ->flowi4_tos. Having
->flowi4_scope initialised with RT_SCOPE_UNIVERSE instead of
RT_SCOPE_LINK probably wasn't really a problem: sockets with the
SOCK_LOCALROUTE flag set (those that'd result in RTO_ONLINK being set)
normally shouldn't receive ICMP redirects or PMTU updates.
That happened because hdev->power_on is already called before
sdio_set_drvdata which btmtksdio_interrupt handler relies on is not
properly set up.
The details are shown as the below: hci_register_dev would run
queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI
workqueue_struct to complete the power-on sequeunce and thus hci_power_on
may run before sdio_set_drvdata is done in btmtksdio_probe.
The hci_dev_do_open in hci_power_on would initialize the device and enable
the interrupt and thus it is possible that btmtksdio_interrupt is being
called right before sdio_set_drvdata is filled out.
When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled
, the kernel oops is going to happen because btmtksdio_interrupt access an
uninitialized pointer.
Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Reviewed-by: Mark Chen <markyawenchen@gmail.com> Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
hci_le_conn_failed function's documentation says that the caller must
hold hdev->lock. The only callsite that does not hold that lock is
hci_le_conn_failed. The other 3 callsites hold the hdev->lock very
locally. The solution is to hold the lock during the call to
hci_le_conn_failed.
The helper macro that records an error in BPF programs that exercise sock
fields access has been inadvertently broken by adaptation work that
happened in commit b18c1f0aa477 ("bpf: selftest: Adapt sock_fields test to
use skel and global variables").
BPF_NOEXIST flag cannot be used to update BPF_MAP_TYPE_ARRAY. The operation
always fails with -EEXIST, which in turn means the error never gets
recorded, and the checks for errors always pass.
Revert the change in update flags.
Fixes: b18c1f0aa477 ("bpf: selftest: Adapt sock_fields test to use skel and global variables") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20220317113920.1068535-2-jakub@cloudflare.com Signed-off-by: Sasha Levin <sashal@kernel.org>
bareudp_create_sock() use AF_INET6 by default if IPv6 CONFIG enabled.
But if user start kernel with ipv6.disable=1, the bareudp sock will
created failed, which cause the interface open failed even with ethertype
ip. e.g.
# ip link add bareudp1 type bareudp dstport 2 ethertype ip
# ip link set bareudp1 up
RTNETLINK answers: Address family not supported by protocol
Fix it by using ipv6_mod_enabled() to check if IPv6 enabled. There is
no need to check IS_ENABLED(CONFIG_IPV6) as ipv6_mod_enabled() will
return false when CONFIG_IPV6 no enabled in include/linux/ipv6.h.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20220315062618.156230-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When providing the MSG_TRUNC flag via recvmsg() syscall the return value
provides the real length of the packet or datagram, even when it was longer
than the passed buffer.
When reading from an unbound can-isotp socket the syscall blocked
indefinitely. As unbound sockets (without given CAN address information)
do not make sense anyway we directly return -EADDRNOTAVAIL on read()
analogue to the known behavior from sendmsg().
The rts51x_read_mem() function should return negative error codes.
Currently if the kmalloc() fails it returns USB_STOR_TRANSPORT_ERROR (3)
which is treated as success by the callers.
Fixes: 065e60964e29 ("ums_realtek: do not use stack memory for DMA") Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220304073504.GA26464@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running xdpsock for a fix duration of time before terminating
using --duration=<n>, there is a race condition that may cause xdpsock
to terminate immediately.
When running for a fixed duration of time the check to determine when to
terminate execution is in is_benchmark_done() and is being executed in
the context of the poller thread,
if (opt_duration > 0) {
unsigned long dt = (get_nsecs() - start_time);
if (dt >= opt_duration)
benchmark_done = true;
}
However start_time is only set after the poller thread have been
created. This leaves a small window when the poller thread is starting
and calls is_benchmark_done() for the first time that start_time is not
yet set. In that case start_time have its initial value of 0 and the
duration check fails as it do not correlate correctly for the
applications start time and immediately sets benchmark_done which in
turn terminates the xdpsock application.
Fix this by setting start_time before creating the poller thread.
Fixes: d3f11b018f6c ("samples/bpf: xdpsock: Add duration option to specify how long to run") Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220315102948.466436-1-niklas.soderlund@corigine.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The mem of msg has been uncharged in tcp_bpf_send_verdict() by
sk_msg_return(), and would be uncharged by sk_msg_free() again. When psock
is null, we can simply returning an error code, this would then trigger
the sk_msg_free_nocharge in the error path of __SK_REDIRECT and would have
the side effect of throwing an error up to user space. This would be a
slight change in behavior from user side but would look the same as an
error if the redirect on the socket threw an error.
This issue can cause the following info:
WARNING: CPU: 0 PID: 2136 at net/ipv4/af_inet.c:155 inet_sock_destruct+0x13c/0x260
Call Trace:
<TASK>
__sk_destruct+0x24/0x1f0
sk_psock_destroy+0x19b/0x1c0
process_one_work+0x1b3/0x3c0
worker_thread+0x30/0x350
? process_one_work+0x3c0/0x3c0
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20220304081145.2037182-5-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If tcp_bpf_sendmsg() is running while sk msg is full. When sk_msg_alloc()
returns -ENOMEM error, tcp_bpf_sendmsg() goes to wait_for_memory. If partial
memory has been alloced by sk_msg_alloc(), that is, msg_tx->sg.size is
greater than osize after sk_msg_alloc(), memleak occurs. To fix we use
sk_msg_trim() to release the allocated memory, then goto wait for memory.
Other call paths of sk_msg_alloc() have the similar issue, such as
tls_sw_sendmsg(), so handle sk_msg_trim logic inside sk_msg_alloc(),
as Cong Wang suggested.
This issue can cause the following info:
WARNING: CPU: 3 PID: 7950 at net/core/stream.c:208 sk_stream_kill_queues+0xd4/0x1a0
Call Trace:
<TASK>
inet_csk_destroy_sock+0x55/0x110
__tcp_close+0x279/0x470
tcp_close+0x1f/0x60
inet_release+0x3f/0x80
__sock_release+0x3d/0xb0
sock_close+0x11/0x20
__fput+0x92/0x250
task_work_run+0x6a/0xa0
do_exit+0x33b/0xb60
do_group_exit+0x2f/0xa0
get_signal+0xb6/0x950
arch_do_signal_or_restart+0xac/0x2a0
exit_to_user_mode_prepare+0xa9/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
</TASK>
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Co-developed-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
pgd page is freed by generic implementation pgd_free() since commit f9cb654cb550 ("asm-generic: pgalloc: provide generic pgd_free()"),
however, there are scenarios that the system uses more than one page as
the pgd table, in such cases the generic implementation pgd_free() won't
be applicable anymore. For example, when PAGE_SIZE_4KB is enabled and
MIPS_VA_BITS_48 is not enabled in a 64bit system, the macro "PGD_ORDER"
will be set as "1", which will cause allocating two pages as the pgd
table. Well, at the same time, the generic implementation pgd_free()
just free one pgd page, which will result in the memory leak.
The memory leak can be easily detected by executing shell command:
"while true; do ls > /dev/null; grep MemFree /proc/meminfo; done"
Fixes: f9cb654cb550 ("asm-generic: pgalloc: provide generic pgd_free()") Signed-off-by: Yaliang Wang <Yaliang.Wang@windriver.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) argument or environment
strings. Also, error return codes don't mean anything to
obsolete_checksetup() -- only non-zero (usually 1) or zero.
So return 1 from setup_kmac().
Fixes: 9e21c7e40b7e ("MIPS: RB532: Replace parse_mac_addr() with mac_pton().") Fixes: 73b4390fb234 ("[MIPS] Routerboard 532: Support for base system") Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
From: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Phil Sutter <n0-1@freewrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Daniel Walter <dwalter@google.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
This function only calls of_node_put() in the regular path.
And it will cause refcount leak in error path.
Fixes: 727fec790ead ("ath10k: Setup the msa resources before qmi init") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220308070238.19295-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The vxcan driver provides a pair of virtual CAN interfaces to exchange
CAN traffic between different namespaces - analogue to veth.
In opposite to the vcan driver the local sent CAN traffic on this interface
is not echo'ed back but only sent to the remote peer. This is unusual and
can be easily fixed by removing IFF_ECHO from the netdevice flags that
are set for vxcan interfaces by default at startup.
Without IFF_ECHO set on driver level, the local sent CAN frames are echo'ed
in af_can.c in can_send(). This patch makes vxcan interfaces adopt the
same local echo behavior and procedures as known from the vcan interfaces.
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)") Link: https://lore.kernel.org/all/20220309120416.83514-5-socketcan@hartkopp.net Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
mpc8xx_pic_init() should return -ENOMEM instead of 0 when
irq_domain_add_linear() return NULL. This cause mpc8xx_pics_init to continue
executing even if mpc8xx_pic_host is NULL.
In test_lwt_ip_encap, the ingress IPv6 encap test failed from time to
time. The failure occured when an IPv4 ping through the IPv6 GRE
encapsulation did not receive a reply within the timeout. The IPv4 ping
and the IPv6 ping in the test used different timeouts (1 sec for IPv4
and 6 sec for IPv6), probably taking into account that IPv6 might need
longer to successfully complete. However, when IPv4 pings (with the
short timeout) are encapsulated into the IPv6 tunnel, the delays of IPv6
apply.
The actual reason for the long delays with IPv6 was that the IPv6
neighbor discovery sometimes did not complete in time. This was caused
by the outgoing interface only having a tentative link local address,
i.e., not having completed DAD for that lladdr. The ND was successfully
retried after 1 sec but that was too late for the ping timeout.
The IPv6 addresses for the test were already added with nodad. However,
for the lladdrs, DAD was still performed. We now disable DAD in the test
netns completely and just assume that the two lladdrs on each veth pair
do not collide. This removes all the delays for IPv6 traffic in the
test.
Without the delays, we can now also reduce the delay of the IPv6 ping to
1 sec. This makes the whole test complete faster because we don't need
to wait for the excessive timeout for each IPv6 ping that is supposed
to fail.
xsk_umem__create() does mmap for fill/comp rings, but xsk_umem__delete()
doesn't do the unmap. This works fine for regular cases, because
xsk_socket__delete() does unmap for the rings. But for the case that
xsk_socket__create_shared() fails, umem rings are not unmapped.
fill_save/comp_save are checked to determine if rings have already be
unmapped by xsk. If fill_save and comp_save are NULL, it means that the
rings have already been used by xsk. Then they are supposed to be
unmapped by xsk_socket__delete(). Otherwise, xsk_umem__delete() does the
unmap.
Fixes: 2f6324a3937f ("libbpf: Support shared umems between queues and devices") Signed-off-by: Cheng Li <lic121@chinatelecom.cn> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20220301132623.GA19995@vscode.7~ Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the devm_request_threaded_irq(),
it should be better to check the return value of the
mc13xxx_irq_request() and return error if fails.
Fixes: 8e00593557c3 ("mfd: Add mc13892 support to mc13xxx") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20220224022331.3208275-1-jiasheng@iscas.ac.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
Include the DECstation interrupt handler in opting out of
FPU support.
Fixes a linker error:
mips-linux-ld: arch/mips/dec/int-handler.o: in function `fpu':
(.text+0x148): undefined reference to `handle_fpe_int'
Fixes: 183b40f992c8 ("MIPS: Allow FP support to be disabled") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: linux-mips@vger.kernel.org Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a memory allocation error occurred during an attempt to refill a slot
in the RX ring after the packet was received, the hardware tail pointer
would still have been updated to point to or past the slot which remained
marked as previously completed. This would likely result in the DMA engine
raising an error when it eventually tried to use that slot again.
If a slot cannot be refilled, then just stop processing and do not move
the tail pointer past it. On the next attempt, we should skip receiving
the packet from the empty slot and just try to refill it again.
This failure mode has not actually been observed, but was found as part
of other driver updates.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb2659230120, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org> Fixes: fb2659230120 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes") Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598cdc ("i2c: Add support for Xilinx XPS IIC Bus Interface") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per Intel's SDM on the "Instruction Set Reference", when
loading segment descriptor, not-present segment check should
be after all type and privilege checks. But the emulator checks
it first, then #NP is triggered instead of #GP if privilege fails
and segment is not present. Put not-present segment check after
type and privilege checks in __load_segment_descriptor().
Fixes: 38ba30ba51a00 (KVM: x86 emulator: Emulate task switch in emulator.c) Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <52573c01d369f506cadcf7233812427cf7db81a7.1644292363.git.houwenlong.hwl@antgroup.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In emulation of writing to cr8, one of the lowest four bits in TPR[3:0]
is kept.
According to Intel SDM 10.8.6.1(baremetal scenario):
"APIC.TPR[bits 7:4] = CR8[bits 3:0], APIC.TPR[bits 3:0] = 0";
and SDM 28.3(use TPR shadow):
"MOV to CR8. The instruction stores bits 3:0 of its source operand into
bits 7:4 of VTPR; the remainder of VTPR (bits 3:0 and bits 31:8) are
cleared.";
and AMD's APM 16.6.4:
"Task Priority Sub-class (TPS)-Bits 3 : 0. The TPS field indicates the
current sub-priority to be used when arbitrating lowest-priority messages.
This field is written with zero when TPR is written using the architectural
CR8 register.";
so in KVM emulated scenario, clear TPR[3:0] to make a consistent behavior
as in other scenarios.
This doesn't impact evaluation and delivery of pending virtual interrupts
because processor does not use the processor-priority sub-class to
determine which interrupts to delivery and which to inhibit.
Sub-class is used by hardware to arbitrate lowest priority interrupts,
but KVM just does a round-robin style delivery.
When CONFIG_GENERIC_CPU=y (true for all our defconfigs) we pass
-mcpu=powerpc64 to the compiler, even when we're building a 32-bit
kernel.
This happens because we have an ifdef CONFIG_PPC_BOOK3S_64/else block in
the Makefile that was written before 32-bit supported GENERIC_CPU. Prior
to that the else block only applied to 64-bit Book3E.
The GCC man page says -mcpu=powerpc64 "[specifies] a pure ... 64-bit big
endian PowerPC ... architecture machine [type], with an appropriate,
generic processor model assumed for scheduling purposes."
It's unclear how that interacts with -m32, which we are also passing,
although obviously -m32 is taking precedence in some sense, as the
32-bit kernel only contains 32-bit instructions.
This was noticed by inspection, not via any bug reports, but it does
affect code generation. Comparing before/after code generation, there
are some changes to instruction scheduling, and the after case (with
-mcpu=powerpc64 removed) the compiler seems more keen to use r8.
Fix it by making the else case only apply to Book3E 64, which excludes
32-bit.
Executing node_set_online() when nid = NUMA_NO_NODE results in an
undefined behavior. node_set_online() will call node_set_state(), into
__node_set(), into set_bit(), and since NUMA_NO_NODE is -1 we'll end up
doing a negative shift operation inside
arch/powerpc/include/asm/bitops.h. This potential UB was detected
running a kernel with CONFIG_UBSAN.
The behavior was introduced by commit 10f78fd0dabb ("powerpc/numa: Fix a
regression on memoryless node 0"), where the check for nid > 0 was
removed to fix a problem that was happening with nid = 0, but the result
is that now we're trying to online NUMA_NO_NODE nids as well.
Checking for nid >= 0 will allow node 0 to be onlined while avoiding
this UB with NUMA_NO_NODE.
Fixes: 10f78fd0dabb ("powerpc/numa: Fix a regression on memoryless node 0") Reported-by: Ping Fang <pifang@redhat.com> Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220224182312.1012527-1-danielhb413@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
insn_to_jit_off passed to bpf_prog_fill_jited_linfo() is calculated in
instruction granularity instead of bytes granularity, but BPF line info
requires byte offset.
bpf_prog_fill_jited_linfo() will be the last user of ctx.offset before
it is freed, so convert the offset into byte-offset before calling into
bpf_prog_fill_jited_linfo() in order to fix the line info dump on arm64.
Fixes: 37ab566c178d ("bpf: arm64: Enable arm64 jit to provide bpf_line_info") Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220226121906.5709-3-houtao1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
BPF line info needs ctx->offset to be the instruction offset in the whole JITed
image instead of the body itself, so also call build_prologue() first in first
JIT pass.
Fixes: 37ab566c178d ("bpf: arm64: Enable arm64 jit to provide bpf_line_info") Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220226121906.5709-2-houtao1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the permission of parameter prot_mask is 0x0, which means that
the member does not appear in sysfs. Change it as other module parameters
to 0444 for world-readable.
[mkp: s/v3/v2/]
Link: https://lore.kernel.org/r/1645703489-87194-2-git-send-email-john.garry@huawei.com Fixes: d6a9000b81be ("scsi: hisi_sas: Add support for DIF feature for v2 hw") Reported-by: Yihang Li <liyihang6@hisilicon.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to calculate the max file size accurately if the total blocks
that can address by block tree exceed the upper_limit. But this check is
not correct now, it only compute the total data blocks but missing
metadata blocks are needed. So in the case of "data blocks < upper_limit
&& total blocks > upper_limit", we will get wrong result. Fortunately,
this case could not happen in reality, but it's confused and better to
correct the computing.
__setup() handlers should return 1 if the parameter is handled.
Returning 0 causes the entire string to be added to init's
environment strings (limited to 32 strings), unnecessarily polluting it.
Using the documented strings "TOMOYO_loader=string1" and
"TOMOYO_trigger=string2" causes an Unknown parameter message:
Unknown kernel command line parameters
"BOOT_IMAGE=/boot/bzImage-517rc5 TOMOYO_loader=string1 \
TOMOYO_trigger=string2", will be passed to user space.
and these strings are added to init's environment string space:
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
TOMOYO_loader=string1
TOMOYO_trigger=string2
With this change, these __setup handlers act as expected,
and init's environment is not polluted with these strings.
Fixes: 0e4ae0e0dec63 ("TOMOYO: Make several options configurable.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Link: https://lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: James Morris <jmorris@namei.org> Cc: Kentaro Takeda <takedakn@nttdata.co.jp> Cc: tomoyo-dev-en@lists.osdn.me Cc: "Serge E. Hallyn" <serge@hallyn.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an ODP MR cache entry is empty and trying to allocate it, increment
the ent->miss counter and call to queue_adjust_cache_locked() to verify
the entry is balanced.
In pm80xx_send_abort_all(), the n_elem field of the ccb used is not
initialized to 0. This missing initialization sometimes lead to the task
completion path seeing the ccb with a non-zero n_elem resulting in the
execution of invalid dma_unmap_sg() calls in pm8001_ccb_task_free(),
causing a crash such as:
Avoid this issue by always initializing the ccb n_elem field to 0 in
pm8001_send_abort_all(), pm8001_send_read_log() and
pm80xx_send_abort_all().
Link: https://lore.kernel.org/r/20220220031810.738362-17-damien.lemoal@opensource.wdc.com Fixes: c6b9ef5779c3 ("[SCSI] pm80xx: NCQ error handling changes") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
NCQ NON DATA is an NCQ command with the DMA_NONE DMA direction and so a
register-device-to-host-FIS response is expected for it.
However, for an IO_SUCCESS case, mpi_sata_completion() expects a
set-device-bits-FIS for any ata task with an use_ncq field true, which
includes NCQ NON DATA commands.
Fix this to correctly treat NCQ NON DATA commands as non-data by also
testing for the DMA_NONE DMA direction.
Link: https://lore.kernel.org/r/20220220031810.738362-16-damien.lemoal@opensource.wdc.com Fixes: dbf9bfe61571 ("[SCSI] pm8001: add SAS/SATA HBA driver") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the pm8001_chip_sata_req() and pm80xx_chip_sata_req() functions, all
tasks with a DMA direction of DMA_NONE (no data transfer) are initialized
using the ATAP value 0x04. However, NCQ NON DATA commands, while being
DMA_NONE commands are NCQ commands and need to be initialized using the
value 0x07 for ATAP, similarly to other NCQ commands.
Make sure that NCQ NON DATA command tasks are initialized similarly to
other NCQ commands by also testing the task "use_ncq" field in addition to
the DMA direction. While at it, reorganize the code into a chain of if -
else if - else to avoid useless affectations and debug messages.
Link: https://lore.kernel.org/r/20220220031810.738362-15-damien.lemoal@opensource.wdc.com Fixes: dbf9bfe61571 ("[SCSI] pm8001: add SAS/SATA HBA driver") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure that the __le32 fields of struct sata_cmd are manipulated after
applying the correct endian conversion. That is, use cpu_to_le32() for
assigning values and le32_to_cpu() for consulting a field value. In
particular, make sure that the calculations for the 4G boundary check are
done using CPU endianness and *not* little endian values. With these fixes,
many sparse warnings are removed.
While at it, fix some code identation and add blank lines after variable
declarations and in some other places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-12-damien.lemoal@opensource.wdc.com Fixes: 0ecdf00ba6e5 ("[SCSI] pm80xx: 4G boundary fix.") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure that the __le32 fields of struct ssp_ini_io_start_req are
manipulated after applying the correct endian conversion. That is, use
cpu_to_le32() for assigning values and le32_to_cpu() for consulting a field
value. In particular, make sure that the calculations for the 4G boundary
check are done using CPU endianness and *not* little endian values. With
these fixes, many sparse warnings are removed.
While at it, add blank lines after variable declarations and in some other
places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-11-damien.lemoal@opensource.wdc.com Fixes: 0ecdf00ba6e5 ("[SCSI] pm80xx: 4G boundary fix.") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All fields of the kek_mgmt_req structure have the type __le32. So make sure
to use cpu_to_le32() to initialize them. This suppresses the sparse
warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] new_curidx_ksop
got int
Link: https://lore.kernel.org/r/20220220031810.738362-10-damien.lemoal@opensource.wdc.com Fixes: f5860992db55 ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All fields of the SASProtocolTimerConfig structure have the __le32 type.
As such, use cpu_to_le32() to initialize them. This change suppresses many
sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [usertype] pageCode
got int
Note that the check to limit the value of the STP_IDLE_TMO field is removed
as this field is initialized using the fixed (and small) value defined by
the STP_IDLE_TIME macro.
The pm8001_dbg() calls printing the values of the SASProtocolTimerConfig
structure fileds are changed to use le32_to_cpu() to present the values in
human readable form.
Link: https://lore.kernel.org/r/20220220031810.738362-9-damien.lemoal@opensource.wdc.com Fixes: a6cb3d012b98 ("[SCSI] pm80xx: thermal, sas controller config and error handling update") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fields of the set_ctrl_cfg_req structure have the __le32 type, so use
cpu_to_le32() to assign them. This removes the sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32
got unsigned int
Link: https://lore.kernel.org/r/20220220031810.738362-8-damien.lemoal@opensource.wdc.com Fixes: 842784e0d15b ("pm80xx: Update For Thermal Page Code") Fixes: f5860992db55 ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files") Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ds_ads_m field of struct ssp_ini_tm_start_req has the type __le32.
Assigning a value to it should thus use cpu_to_le32(). This fixes the
sparse warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] ds_ads_m
got int
Link: https://lore.kernel.org/r/20220220031810.738362-7-damien.lemoal@opensource.wdc.com Fixes: dbf9bfe61571 ("[SCSI] pm8001: add SAS/SATA HBA driver") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the sata_cmd struct is zeroed out before its fields are initialized,
there is no need for using "|=" to initialize the ncqtag_atap_dir_m
field. Using a standard assignment removes the sparse warning:
warning: invalid assignment: |=
Also, since the ncqtag_atap_dir_m field has type __le32, use cpu_to_le32()
to generate the assigned value.
Link: https://lore.kernel.org/r/20220220031810.738362-5-damien.lemoal@opensource.wdc.com Fixes: c6b9ef5779c3 ("[SCSI] pm80xx: NCQ error handling changes") Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Explicitly convert unsigned int in the right of the conditional
expression to int to match the left side operand and the return type,
fixing the following compiler warning:
drivers/md/dm-crypt.c:2593:43: warning: signed and unsigned
type in conditional expression [-Wsign-compare]
Fixes: c538f6ec9f56 ("dm crypt: add ability to use keys from the kernel key retention service") Signed-off-by: Aashish Sharma <shraash@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
DP audio enablement code which is comparing intf_type,
DRM_MODE_ENCODER_TMDS (= 2) with DRM_MODE_CONNECTOR_DisplayPort (= 10).
Which would never succeed. Fix it to check for DRM_MODE_ENCODER_TMDS.
Fixes: d13e36d7d222 ("drm/msm/dp: add audio support for Display Port on MSM") Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220217035358.465904-2-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose
and expect DP source return correct checksum. During drm edid read,
correct edid checksum is calculated and stored at
connector::real_edid_checksum.
The problem is struct dp_panel::connector never be assigned, instead the
connector is stored in struct msm_dp::connector. When we run compliance
testing test case 4.2.2.6 dp_panel_handle_sink_request() won't have a valid
edid set in struct dp_panel::edid so we'll try to use the connectors
real_edid_checksum and hit a NULL pointer dereference error because the
connector pointer is never assigned.
Changes in V2:
-- populate panel connector at msm_dp_modeset_init() instead of at dp_panel_read_sink_caps()
Changes in V3:
-- remove unhelpful kernel crash trace commit text
-- remove renaming dp_display parameter to dp
Changes in V4:
-- add more details to commit text
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Currently the error -EIO is being assinged to variable ret when
the READY_BIT is not set but the function iwlagn_mac_start returns
0 rather than ret. Fix this by returning ret instead of 0.
Addresses-Coverity: ("Unused value") Fixes: 7335613ae27a ("iwlwifi: move all mac80211 related functions to one place") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210907104658.14706-1-colin.king@canonical.com Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is caused by dax_fs_exit() not flushing inodes before destroy cache.
To fix this issue, call rcu_barrier() before destroy cache.
Signed-off-by: Tong Zhang <ztong0001@gmail.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220212071111.148575-1-ztong0001@gmail.com Fixes: 7b6be8444e0f ("dax: refactor dax-fs into a generic provider of 'struct dax_device' instances") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
When display topology changed on DSC hub we add all crtcs with dsc support to
atomic state.
Refer to patch:"drm/amd/display: Trigger modesets on MST DSC connectors"
However the original implementation may skip crtc if the topology change
caused by unplug.
That potentially could lead to no-lightup or corruption on DSC hub after
unplug event on one of the connectors.
[How]
Update add_affected_mst_dsc_crtcs() to use old connector state
if new connector state has no crtc (undergoes modeset due to unplug)
Fixes: 44be939ff7ac58 ("drm/amd/display: Trigger modesets on MST DSC connectors") Reviewed-by: Hersen Wu <hersenwu@amd.com> Acked-by: Jasdeep Dhillon <jdhillon@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
pm sysfs should be writable in one VF mode as is in passthrough
[how]
do not remove write access on pm sysfs if device is in one VF mode
Fixes: 11c9cc95f818 ("amdgpu/pm: Make sysfs pm attributes as read-only for VFs") Signed-off-by: Yiqing Yao <yiqing.yao@amd.com> Reviewed-by: Monk Liu <Monk.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
Internally kernel prepends all report buffers, for both numbered and
unnumbered reports, with report ID, therefore to properly handle unnumbered
reports we should prepend it ourselves.
For the same reason we should skip the first byte of the buffer when
calling i2c_hid_set_or_send_report() which then will take care of properly
formatting the transfer buffer based on its separate report ID argument
along with report payload.
[jkosina@suse.cz: finalize trimmed sentence in changelog as spotted by Benjamin] Fixes: 9b5a9ae88573 ("HID: i2c-hid: implement ll_driver transport-layer callbacks") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d128 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com> Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Fixes: 6c3c719936da ("drm/bridge: synopsys: dw-hdmi: add bus format negociation") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit] Reviewed-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
Running with POSIXLY_CORRECT=1 in the environment the scripts/dtc build
fails, because pkg-config doesn't output anything when the flags come
after the arguments.
Fixes: 067c650c456e ("dtc: Use pkg-config to locate libyaml") Signed-off-by: Thomas Bracht Laumann Jespersen <t@laumann.xyz> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220131112028.7907-1-t@laumann.xyz Signed-off-by: Sasha Levin <sashal@kernel.org>
mac80211 provides aid in vif->bss_conf.aid for sta mode and not in
sta->aid. Fix mt7915_mcu_wtbl_generic_tlv routine using proper value for
aid in sta mode.
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trace IMC (In-Memory collection counters) in powerpc is useful for
application level profiling.
For trace_imc, presently task context (task_ctx_nr) is set to
perf_hw_context. But perf_hw_context should only be used for CPU PMU.
See commit 26657848502b ("perf/core: Verify we have a single
perf_hw_context PMU").
So for trace_imc, even though it is per thread PMU, it is preferred to
use sw_context in order to be able to do application level monitoring.
Hence change the task_ctx_nr to use perf_sw_context.
On board rev A, the network interface labels for the switch ports
written on the front panel are different than on rev B and later.
This patch fixes network interface names for the switch ports according
to labels that are written on the front panel of the board rev B.
They start from ETH3 and end at ETH10.
This patch also introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
As the possible failure of the ioremap(), the 'local->sram' and other
two could be NULL.
Therefore it should be better to check it in order to avoid the later
dev_dbg.
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match i40e_construct_skb().
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support") Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com> Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, i40e_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
The MMIO emulation code for vector instructions is duplicated between
VSX and VMX. When emulating VMX we should check the VMX copy size
instead of the VSX one.
Syzbot reported 2 KMSAN bugs in ath9k. All of them are caused by missing
field initialization.
In htc_connect_service() svc_meta_len and pad are not initialized. Based
on code it looks like in current skb there is no service data, so simply
initialize svc_meta_len to 0.
htc_issue_send() does not initialize htc_frame_hdr::control array. Based
on firmware code, it will initialize it by itself, so simply zero whole
array to make KMSAN happy
Bytes 16-17 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+f83a1df1ed4f67e8d8ad@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220115122733.11160-1-paskripkin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
clang static analysis reports this represenative problem
amdgpu_smu.c:144:18: warning: The left operand of '*' is a garbage value
return clk_freq * 100;
~~~~~~~~ ^
If there is no get_dpm_ultimate_freq function,
smu_get_dpm_freq_range returns success without setting the
output min,max parameters. So return an -ENOTSUPP error.
Fixes: e5ef784b1e17 ("drm/amd/powerplay: revise calling chain on retrieving frequency range") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log