This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_resume_and_get() wraps around pm_runtime_get_sync() and
decrements the runtime PM usage counter in case the latter function
fails and keeps the counter balanced.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for
data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will
free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after
kfree() to avoid double free.
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
As a bonus, as pm_runtime_get_sync() always return 0 on
success, the logic can be simplified.
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
The bdisp_start_streaming() doesn't take it into account, which
would unbalance PM usage counter at bdisp_stop_streaming().
The logic at bdisp_probe() is correct, but the best is to use
the same call along the driver.
So, replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
As a plus, pm_runtime_resume_and_get() doesn't return
positive numbers, so the return code validation can
be removed.
Currently, the driver just assumes that PM runtime logic
succeded resuming the device.
That may not be the case, as pm_runtime_get_sync()
can fail (but keeping the usage count incremented).
Replace the code to use pm_runtime_resume_and_get(),
and letting it return the error code.
This way, if mtk_vcodec_dec_pw_on() fails, the logic
under fops_vcodec_open() will do the right thing and
return an error, instead of just assuming that the
device is ready to be used.
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
While here, check if the PM runtime error was caught at open time.
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
While here, check if the PM runtime error was caught at
s5p_cec_adap_enable().
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
While here, fix the return contition of mtk_mdp_m2m_start_streaming(),
as it doesn't make any sense to return 0 if the PM runtime failed
to resume.
Currently, the SPI core doesn't set the struct device fwnode pointer
when it creates a new SPI device. This means when the device is
registered the fwnode is NULL and the check in device_add which sets
the fwnode->dev pointer is skipped. This wasn't previously an issue,
however these two patches:
commit 4731210c09f5 ("gpiolib: Bind gpio_device to a driver to enable
fw_devlink=on by default")
commit ced2af419528 ("gpiolib: Don't probe gpio_device if it's not the
primary device")
Added some code to the GPIO core which relies on using that
fwnode->dev pointer to determine if a driver is bound to the fwnode
and if not bind a stub GPIO driver. This means the GPIO providers
behind SPI will get both the expected driver and this stub driver
causing the stub driver to fail if it attempts to request any pin
configuration. For example on my system:
madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3
madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl
gpio_stub_drv gpiochip3: Error applying setting, reverse things back
gpio_stub_drv: probe of gpiochip3 failed with error -22
The firmware node on the device created by the GPIO framework is set
through the of_node pointer hence things generally actually work,
however that fwnode->dev is never set, as the check was skipped at
device_add time. This fix appears to match how the I2C subsystem
handles the same situation.
A request could end up on the fpq->io list after fuse_abort_conn() has
reset fpq->connected and aborted requests on that list:
Thread-1 Thread-2
======== ========
->fuse_simple_request() ->shutdown
->__fuse_request_send()
->queue_request() ->fuse_abort_conn()
->fuse_dev_do_read() ->acquire(fpq->lock)
->wait_for(fpq->lock) ->set err to all req's in fpq->io
->release(fpq->lock)
->acquire(fpq->lock)
->add req to fpq->io
After the userspace copy is done the request will be ended, but
req->out.h.error will remain uninitialized. Also the copy might block
despite being already aborted.
Fix both issues by not allowing the request to be queued on the fpq->io
list after fuse_abort_conn() has processed this list.
Reported-by: Pradeep P V K <pragalla@codeaurora.org> Fixes: fd22d62ed0c3 ("fuse: no fc->lock for iqueue parts") Cc: <stable@vger.kernel.org> # v4.2 Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the "fuse: trying to steal weird page" warning.
Description from Johannes Weiner:
"Think of it as similar to PG_active. It's just another usage/heat
indicator of file and anon pages on the reclaim LRU that, unlike
PG_active, persists across deactivation and even reclaim (we store it in
the page cache / swapper cache tree until the page refaults).
So if fuse accepts pages that can legally have PG_active set,
PG_workingset is fine too."
EVM_ALLOW_METADATA_WRITES is an EVM initialization flag that can be set to
temporarily disable metadata verification until all xattrs/attrs necessary
to verify an EVM portable signature are copied to the file. This flag is
cleared when EVM is initialized with an HMAC key, to avoid that the HMAC is
calculated on unverified xattrs/attrs.
Currently EVM unnecessarily denies setting this flag if EVM is initialized
with a public key, which is not a concern as it cannot be used to trust
xattrs/attrs updates. This patch removes this limitation.
evm_inode_init_security() requires an HMAC key to calculate the HMAC on
initial xattrs provided by LSMs. However, it checks generically whether a
key has been loaded, including also public keys, which is not correct as
public keys are not suitable to calculate the HMAC.
Originally, support for signature verification was introduced to verify a
possibly immutable initial ram disk, when no new files are created, and to
switch to HMAC for the root filesystem. By that time, an HMAC key should
have been loaded and usable to calculate HMACs for new files.
More recently support for requiring an HMAC key was removed from the
kernel, so that signature verification can be used alone. Since this is a
legitimate use case, evm_inode_init_security() should not return an error
when no HMAC key has been loaded.
This patch fixes this problem by replacing the evm_key_loaded() check with
a check of the EVM_INIT_HMAC flag in evm_initialized.
In raise_backtrace_ipi() we iterate through the cpumask of CPUs, sending
each an IPI asking them to do a backtrace, but we don't wait for the
backtrace to happen.
We then iterate through the CPU mask again, and if any CPU hasn't done
the backtrace and cleared itself from the mask, we print a trace on its
behalf, noting that the trace may be "stale".
This works well enough when a CPU is not responding, because in that
case it doesn't receive the IPI and the sending CPU is left to print the
trace. But when all CPUs are responding we are left with a race between
the sending and receiving CPUs, if the sending CPU wins the race then it
will erroneously print a trace.
This leads to spurious "stale" traces from the sending CPU, which can
then be interleaved messily with the receiving CPU, note the CPU
numbers, eg:
[ 1658.929157][ C7] rcu: Stack dump where RCU GP kthread last ran:
[ 1658.929223][ C7] Sending NMI from CPU 7 to CPUs 1:
[ 1658.929303][ C1] NMI backtrace for cpu 1
[ 1658.929303][ C7] CPU 1 didn't respond to backtrace IPI, inspecting paca.
[ 1658.929362][ C1] CPU: 1 PID: 325 Comm: kworker/1:1H Tainted: G W E 5.13.0-rc2+ #46
[ 1658.929405][ C7] irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 325 (kworker/1:1H)
[ 1658.929465][ C1] Workqueue: events_highpri test_work_fn [test_lockup]
[ 1658.929549][ C7] Back trace of paca->saved_r1 (0xc0000000057fb400) (possibly stale):
[ 1658.929592][ C1] NIP: c00000000002cf50 LR: c008000000820178 CTR: c00000000002cfa0
To fix it, change the logic so that the sending CPU waits 5s for the
receiving CPU to print its trace. If the receiving CPU prints its trace
successfully then the sending CPU just continues, avoiding any spurious
"stale" trace.
This has the added benefit of allowing all CPUs to print their traces in
order and avoids any interleaving of their output.
Since the raw memory 'data' does not go forward, it will dump repeated
data if the data length is more than 8. If we want to dump longer data
blocks, we need to repeatedly call macro SEQ_PUT_HEX_FIELD. I think it
is a bit redundant, and multiple function calls also affect the performance.
All internal use cases for tracepoint_probe_register() is set to not ever
be called with the same function and data. If it is, it is considered a
bug, as that means the accounting of handling tracepoints is corrupted.
If the function and data for a tracepoint is already registered when
tracepoint_probe_register() is called, it will call WARN_ON_ONCE() and
return with EEXISTS.
The BPF system call can end up calling tracepoint_probe_register() with
the same data, which now means that this can trigger the warning because
of a user space process. As WARN_ON_ONCE() should not be called because
user space called a system call with bad data, there needs to be a way to
register a tracepoint without triggering a warning.
Enter tracepoint_probe_register_may_exist(), which can be called, but will
not cause a WARN_ON() if the probe already exists. It will still error out
with EEXIST, which will then be sent to the user space that performed the
BPF system call.
This keeps the previous testing for issues with other users of the
tracepoint code, while letting BPF call it with duplicated data and not
warn about it.
With the addition of simple mathematical operations (plus and minus), the
parsing of the "sym-offset" modifier broke, as it took the '-' part of the
"sym-offset" as a minus, and tried to break it up into a mathematical
operation of "field.sym - offset", in which case it failed to parse
(unless the event had a field called "offset").
Both .sym and .sym-offset modifiers should not be entered into
mathematical calculations anyway. If ".sym-offset" is found in the
modifier, then simply make it not an operation that can be calculated on.
Link: https://lkml.kernel.org/r/20210707110821.188ae255@oasis.local.home Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: stable@vger.kernel.org Fixes: 100719dcef447 ("tracing: Add simple expression support to hist triggers") Reviewed-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In AP mode WPA2-PSK connections were not established.
The reason was that the AP was sending the first message
of the 4 way handshake encrypted, even though no pairwise
key had (correctly) yet been set.
Encryption was enabled if the "security_enable" driver flag
was set and encryption was not explicitly disabled by
IEEE80211_TX_INTFL_DONT_ENCRYPT.
However security_enable was set when *any* key, including
the AP GTK key, had been set which was causing unwanted
encryption even if no key was avaialble for the unicast
packet to be sent.
Fix this by adding a check that we have a key and drop
the old security_enable driver flag which is insufficient
and redundant.
The Redpine downstream out of tree driver does it this way too.
Regarding the Fixes tag the actual code being modified was
introduced earlier, with the original driver submission, in dad0d04fa7ba ("rsi: Add RS9113 wireless driver"), however
at that time AP mode was not yet supported so there was
no bug at that point.
So I have tagged the introduction of AP support instead
which was part of the patch set "rsi: support for AP mode" [1]
It is not clear whether AP WPA has ever worked, I can see nothing
on the kernel side that broke it afterwards yet the AP support
patch series says "Tests are performed to confirm aggregation,
connections in WEP and WPA/WPA2 security."
One possibility is that the initial tests were done with a modified
userspace (hostapd).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Fixes: 38ef62353acb ("rsi: security enhancements for AP mode") CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1622564459-24430-1-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RSI_RATE_x bits must be assigned to struct rsi_data_desc rate_info
field. The rest of the driver does it correctly, except this one place,
so fix it. This is also aligned with the RSI downstream vendor driver.
Without this patch, an AP operating at 5 GHz does not transmit any
beacons at all, this patch fixes that.
Fixes: d26a9559403c ("rsi: add beacon changes for AP mode") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com> Cc: Angus Ainslie <angus@akkea.ca> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Karun Eagalapati <karun256@gmail.com> Cc: Martin Kepplinger <martink@posteo.de> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Cc: Siva Rebbagondla <siva8118@gmail.com> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210507213105.140138-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It doesn't make sense to clobber the const driver-side buffer, if a
write-to-device attempt failed. All other SSB variants (PCI, PCMCIA and SoC)
also don't corrupt the buffer on any failure in block_write.
Therefore, remove this memset from the SDIO variant.
Signed-off-by: Michael Büsch <m@bues.ch> Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210515210252.318be2ba@wiggum Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got this crash more times during debugging of PCIe controller and crash
happens somehow at the time when PCIe kernel code started link retraining (as
part of ASPM code) when at the same time PCIe link went down and ath9k probably
executed hw reset procedure.
Currently I'm not able to reproduce this issue as it looks like to be
some race condition between link training, ASPM, link down and reset
path. And as always, race conditions which depends on more input
parameters are hard to reproduce as it depends on precise timings.
But it is clear that pointers are zero in this case and should be
properly filled as same code pattern is used in ath9k_stop() function.
Anyway I was able to reproduce this crash by manually triggering ath
reset worker prior putting card up. I created simple patch to export
reset functionality via debugfs and use it to "simulate" of triggering
reset. s proved that NULL-pointer dereference issue is there.
Function ath9k_hw_reset() is dereferencing chan structure pointer, so it
needs to be non-NULL pointer.
Function ath9k_stop() already contains code which sets ah->curchan to valid
non-NULL pointer prior calling ath9k_hw_reset() function.
Add same code pattern also into ath_reset_internal() function to prevent
kernel NULL pointer dereference in ath9k_hw_reset() function.
This change fixes kernel NULL pointer dereference in ath9k_hw_reset() which
is caused by calling ath9k_hw_reset() from ath_reset_internal() with NULL
chan structure.
The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
The ltr559 chip uses only the lowest bit of the ALS_CONTR register to
configure between active and stand-by mode. In the original driver
BIT(1) is used, which does a software reset instead.
This patch fixes the problem by using BIT(0) as als_mode_active for
the ltr559 chip.
Fixes: 8592a7eefa54 ("iio: ltr501: Add support for ltr559 chip") Signed-off-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559 Link: https://lore.kernel.org/r/20210610134619.2101372-3-mkl@pengutronix.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap is configured for 8 bit registers, uses a RB-Tree cache and
marks several registers as volatile (i.e. do not cache).
The ALS and PS data registers in the chip are 16 bit wide and spans
two regmap registers. In the current driver only the base register is
marked as volatile, resulting in the upper register only read once.
Further the data sheet notes:
| When the I2C read operation starts, all four ALS data registers are
| locked until the I2C read operation of register 0x8B is completed.
Which results in the registers never update after the 2nd read.
This patch fixes the problem by marking the upper 8 bits of the ALS
and PS registers as volatile, too.
Fixes: 2f2c96338afc ("iio: ltr501: Add regmap support.") Reported-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559 Link: https://lore.kernel.org/r/20210610134619.2101372-2-mkl@pengutronix.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating an IRQ is conditional to the IRQ existence, but freeing it
was not. If no IRQ was allocate, the driver would still try to free
IRQ 0. Add the missing checks.
This fixes the following trace when the driver is removed:
The STM32MP1 RTC may have 2 clocks, the pclk and the rtc_ck.
If clk_prepare_enable() fails for the second clock (rtc_ck) we must only
call clk_disable_unprepare() for the first clock (pclk) but currently we
call it on both leading to a WARN:
[ 15.629568] WARNING: CPU: 0 PID: 146 at drivers/clk/clk.c:958 clk_core_disable+0xb0/0xc8
[ 15.637620] ck_rtc already disabled
[ 15.663322] CPU: 0 PID: 146 Comm: systemd-udevd Not tainted 5.4.77-pknbsp-svn5759-atag-v5.4.77-204-gea4235203137-dirty #2413
[ 15.674510] Hardware name: STM32 (Device Tree Support)
[ 15.679658] [<c0111148>] (unwind_backtrace) from [<c010c0b8>] (show_stack+0x10/0x14)
[ 15.687371] [<c010c0b8>] (show_stack) from [<c0ab3d28>] (dump_stack+0xc0/0xe0)
[ 15.694574] [<c0ab3d28>] (dump_stack) from [<c012360c>] (__warn+0xc8/0xf0)
[ 15.701428] [<c012360c>] (__warn) from [<c0123694>] (warn_slowpath_fmt+0x60/0x94)
[ 15.708894] [<c0123694>] (warn_slowpath_fmt) from [<c053b518>] (clk_core_disable+0xb0/0xc8)
[ 15.717230] [<c053b518>] (clk_core_disable) from [<c053c190>] (clk_core_disable_lock+0x18/0x24)
[ 15.725924] [<c053c190>] (clk_core_disable_lock) from [<bf0adc44>] (stm32_rtc_probe+0x124/0x5e4 [rtc_stm32])
[ 15.735739] [<bf0adc44>] (stm32_rtc_probe [rtc_stm32]) from [<c05f7d4c>] (platform_drv_probe+0x48/0x98)
[ 15.745095] [<c05f7d4c>] (platform_drv_probe) from [<c05f5cec>] (really_probe+0x1f0/0x458)
[ 15.753338] [<c05f5cec>] (really_probe) from [<c05f61c4>] (driver_probe_device+0x70/0x1c4)
[ 15.761584] [<c05f61c4>] (driver_probe_device) from [<c05f6580>] (device_driver_attach+0x58/0x60)
[ 15.770439] [<c05f6580>] (device_driver_attach) from [<c05f6654>] (__driver_attach+0xcc/0x170)
[ 15.779032] [<c05f6654>] (__driver_attach) from [<c05f40d8>] (bus_for_each_dev+0x58/0x7c)
[ 15.787191] [<c05f40d8>] (bus_for_each_dev) from [<c05f4ffc>] (bus_add_driver+0xdc/0x1f8)
[ 15.795352] [<c05f4ffc>] (bus_add_driver) from [<c05f6ed8>] (driver_register+0x7c/0x110)
[ 15.803425] [<c05f6ed8>] (driver_register) from [<c01027bc>] (do_one_initcall+0x70/0x1b8)
[ 15.811588] [<c01027bc>] (do_one_initcall) from [<c01a1094>] (do_init_module+0x58/0x1f8)
[ 15.819660] [<c01a1094>] (do_init_module) from [<c01a0074>] (load_module+0x1e58/0x23c8)
[ 15.827646] [<c01a0074>] (load_module) from [<c01a0860>] (sys_finit_module+0xa0/0xd4)
[ 15.835459] [<c01a0860>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20)
Currently css_wait_for_slow_path() gets called inside the chp->lock.
The path-verification-loop of slowpath inside this lock could lead to
deadlock as reported by the lockdep validator.
The ccw_device_get_chp_desc() during the instance of a device-set-online
would try to acquire the same 'chp->lock' to read the chp->desc.
The instance of this function can get called from multiple scenario,
like probing or setting-device online manually. This could, in some
corner-cases lead to the deadlock.
The chp->lock was introduced to serialize the access of struct
channel_path. This lock is not needed for the css_wait_for_slow_path()
function, so invoke the slow-path function outside this lock.
LLVM does not emit optimal byteswap assembly, which results in high
stack usage in kvmhv_enter_nested_guest() due to the inlining of
byteswap_pt_regs(). With LLVM 12.0.0:
arch/powerpc/kvm/book3s_hv_nested.c:289:6: error: stack frame size of
2512 bytes in function 'kvmhv_enter_nested_guest' [-Werror,-Wframe-larger-than=]
long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
^
1 error generated.
While this gets fixed in LLVM, mark byteswap_pt_regs() as
noinline_for_stack so that it does not get inlined and break the build
due to -Werror by default in arch/powerpc/. Not inlining saves
approximately 800 bytes with LLVM 12.0.0:
arch/powerpc/kvm/book3s_hv_nested.c:290:6: warning: stack frame size of
1728 bytes in function 'kvmhv_enter_nested_guest' [-Wframe-larger-than=]
long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
^
1 warning generated.
With global filtering, we only allow an event to be scheduled if its
filter settings exactly match those of any existing events, therefore
it is pointless to reapply the filter in that case. Much worse, though,
is that in doing that we trample the event type of counter 0 if it's
already active, and never touch the appropriate PMEVTYPERn so the new
event is likely not counting the right thing either. Don't do that.
When find a task from wait queue to wake up, a non-privileged task may
be found out, rather than the privileged. This maybe lead a deadlock
same as commit dfe1fe75e00e ("NFSv4: Fix deadlock between nfs4_evict_inode()
and nfs4_opendata_get_inode()"):
Privileged delegreturn task is queued to privileged list because all
the slots are assigned. If there has no enough slot to wake up the
non-privileged batch tasks(session less than 8 slot), then the privileged
delegreturn task maybe lost waked up because the found out task can't
get slot since the session is on draining.
So we should treate the privileged task as the emergency task, and
execute it as for as we can.
The 'queue->nr' will wraparound from 0 to 255 when only current
priority queue has tasks. This maybe lead a deadlock same as commit dfe1fe75e00e ("NFSv4: Fix deadlock between nfs4_evict_inode()
and nfs4_opendata_get_inode()"):
Privileged delegreturn task is queued to privileged list because all
the slots are assigned. When non-privileged task complete and release
the slot, a non-privileged maybe picked out. It maybe allocate slot
failed when the session on draining.
If the 'queue->nr' has wraparound to 255, and no enough slot to
service it, then the privileged delegreturn will lost to wake up.
Sending nulldata packets is important for sw AP link probing and detecting
4-address mode links. The checks that dropped these packets were apparently
added to work around an iwlwifi firmware bug with multi-TID aggregation.
Fixes: 41cbb0f5a295 ("mac80211: add support for HE") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20210619101517.90806-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than just indicating that transmission can start, this patch
requires the explicit flushing of the network TX queue when the driver
is informed by the device that it can transmit, next to its
configuration.
In this way, if frames have already been written by the application,
they will actually be transmitted.
Set SOCK_RCU_FREE to let RCU to call sk_destruct() on completion.
Without this patch, we will run in to j1939_can_recv() after priv was
freed by j1939_sk_release()->j1939_sk_sock_destruct()
Fixes: 25fe97cb7620 ("can: j1939: move j1939_priv_put() into sk_destruct callback") Link: https://lore.kernel.org/r/20210617130623.12705-1-o.rempel@pengutronix.de Cc: linux-stable <stable@vger.kernel.org> Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reported-by: syzbot+bdf710cfc41c186fdff3@syzkaller.appspotmail.com Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can_can_gw_rcv() is called under RCU protection, so after calling
can_rx_unregister(), we have to call synchronize_rcu in order to wait
for any RCU read-side critical sections to finish before removing the
kmem_cache entry with the referenced gw job entry.
Link: https://lore.kernel.org/r/20210618173645.2238-1-socketcan@hartkopp.net Fixes: c1aabdf379bc ("can-gw: add netlink based CAN routing") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can_rx_register() callbacks may be called concurrently to the call to
can_rx_unregister(). The callbacks and callback data, though, are
protected by RCU and the struct sock reference count.
So the callback data is really attached to the life of sk, meaning
that it should be released on sk_destruct. However, bcm_remove_op()
calls tasklet_kill(), and RCU callbacks may be called under RCU
softirq, so that cannot be used on kernels before the introduction of
HRTIMER_MODE_SOFT.
However, bcm_rx_handler() is called under RCU protection, so after
calling can_rx_unregister(), we may call synchronize_rcu() in order to
wait for any RCU read-side critical sections to finish. That is,
bcm_rx_handler() won't be called anymore for those ops. So, we only
free them, after we do that synchronize_rcu().
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol") Link: https://lore.kernel.org/r/20210619161813.2098382-1-cascardo@canonical.com Cc: linux-stable <stable@vger.kernel.org> Reported-by: syzbot+0f7e7e5e2f4f40fa89c0@syzkaller.appspotmail.com Reported-by: Norbert Slusarek <nslusarek@gmx.net> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5d1b1b3f492f ("ext4: fix BUG when calling ext4_error with locked
block group") introduces ext4_grp_locked_error to handle unlocking a
group in error cases. Otherwise, there is a possibility of a sleep while
atomic. However, since 43c73221b3b1 ("ext4: replace BUG_ON with WARN_ON
in mb_find_extent()"), mb_find_extent() has contained a ext4_error()
call while a group spinlock is held. Replace this with
ext4_grp_locked_error.
Fixes: 43c73221b3b1 ("ext4: replace BUG_ON with WARN_ON in mb_find_extent()") Cc: <stable@vger.kernel.org> # 4.14+ Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com> Reviewed-by: Lukas Czerner <lczerner@redhat.com> Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20210623232114.34457-1-stephen.s.brennan@oracle.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After converting fs shrinkers to new scan/count API, we are no longer
pass zero nr_to_scan parameter to detect the number of objects to free,
just remove this check.
Fixes: 1ab6c4997e04 ("fs: convert fs shrinkers to new scan/count API") Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210522103045.690103-2-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cache_cnt parameter of tracepoint ext4_es_shrink_exit means the
remaining cache count after shrink, but now it is the cache count before
shrink, fix it by read sbi->s_extent_cache_cnt again.
Fixes: 1ab6c4997e04 ("fs: convert fs shrinkers to new scan/count API") Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210522103045.690103-3-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit c89128a00838 ("ext4: handle errors on
ext4_commit_super"), 'ret' may be set to 0 before calling
ext4_fill_flex_info(), if ext4_fill_flex_info() fails ext4_mount()
doesn't return error code, it makes 'root' is null which causes crash
in legacy_get_tree().
Fixes: c89128a00838 ("ext4: handle errors on ext4_commit_super") Reported-by: Hulk Robot <hulkci@huawei.com> Cc: <stable@vger.kernel.org> # v4.18+ Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210510111051.55650-1-yangyingliang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize eh_generation of struct ext4_extent_header to prevent leaking
info to userspace. Fixes KMSAN kernel-infoleak bug reported by syzbot at:
http://syzkaller.appspot.com/bug?id=78e9ad0e6952a3ca16e8234724b2fa92d041b9b8
In ext4_orphan_cleanup(), if ext4_truncate() failed to get a transaction
handle, it didn't remove the inode from the in-core orphan list, which
may probably trigger below error dump in ext4_destroy_inode() during the
final iput() and could lead to memory corruption on the later orphan
list changes.
The defrag loop processes leaves in batches and starting transaction for
each. The whole defragmentation on a given root is protected by a bit
but in case the transaction fails, the bit is not cleared
In case the transaction fails the bit would prevent starting
defragmentation again, so make sure it's cleared.
During an incremental send operation, when processing the new references
for the current inode, we might send an unlink operation for another inode
that has a conflicting path and has more than one hard link. However this
path was computed and cached before we processed previous new references
for the current inode. We may have orphanized a directory of that path
while processing a previous new reference, in which case the path will
be invalid and cause the receiver process to fail.
The following reproducer triggers the problem and explains how/why it
happens in its comments:
$ cat test-send-unlink.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# Create our test files and directory. Inode 259 (file3) has two hard
# links.
touch $MNT/file1
touch $MNT/file2
touch $MNT/file3
# Now create the base snapshot, which is going to be the parent snapshot
# for a later incremental send.
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send -f /tmp/snap1.send $MNT/snap1
# Move inode 257 into directory inode 260. This results in computing the
# path for inode 260 as "/A" and caching it.
mv $MNT/file1 $MNT/A/file1
# Move inode 258 (file2) into directory inode 260, with a name of
# "hard_link", moving first inode 259 away since it currently has that
# location and name.
mv $MNT/A/hard_link $MNT/tmp
mv $MNT/file2 $MNT/A/hard_link
# Now rename inode 260 to something else (B for example) and then create
# a hard link for inode 258 that has the old name and location of inode
# 260 ("/A").
mv $MNT/A $MNT/B
ln $MNT/B/hard_link $MNT/A
# Create another snapshot of our subvolume and use it for an incremental
# send.
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2
# Now unmount the filesystem, create a new one, mount it and try to
# apply both send streams to recreate both snapshots.
umount $DEV
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# First add the first snapshot to the new filesystem by applying the
# first send stream.
btrfs receive -f /tmp/snap1.send $MNT
# The incremental receive operation below used to fail with the
# following error:
#
# ERROR: unlink A/hard_link failed: No such file or directory
#
# This is because when send is processing inode 257, it generates the
# path for inode 260 as "/A", since that inode is its parent in the send
# snapshot, and caches that path.
#
# Later when processing inode 258, it first processes its new reference
# that has the path of "/A", which results in orphanizing inode 260
# because there is a a path collision. This results in issuing a rename
# operation from "/A" to "/o260-6-0".
#
# Finally when processing the new reference "B/hard_link" for inode 258,
# it notices that it collides with inode 259 (not yet processed, because
# it has a higher inode number), since that inode has the name
# "hard_link" under the directory inode 260. It also checks that inode
# 259 has two hardlinks, so it decides to issue a unlink operation for
# the name "hard_link" for inode 259. However the path passed to the
# unlink operation is "/A/hard_link", which is incorrect since currently
# "/A" does not exists, due to the orphanization of inode 260 mentioned
# before. The path is incorrect because it was computed and cached
# before the orphanization. This results in the receiver to fail with
# the above error.
btrfs receive -f /tmp/snap2.send $MNT
umount $MNT
When running the test, it fails like this:
$ ./test-send-unlink.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: unlink A/hard_link failed: No such file or directory
Fix this by recomputing a path before issuing an unlink operation when
processing the new references for the current inode if we previously
have orphanized a directory.
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3a95200d3f89 ("arm_pmu: Change API to support 64bit counter values")
changes the input "value" type from 32-bit to 64-bit, which introduces the
following problem: ARMv7 PMU counters is 32-bit width, in big-endian mode,
write counter uses high 32-bit, which writes an incorrect value.
Fixes: 3a95200d3f89 ("arm_pmu: Change API to support 64bit counter values") Cc: <stable@vger.kernel.org> Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/r/20210430012659.232110-1-yangjihong1@huawei.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though we validate user-provided inputs we then traverse past
validated data when applying the new map. The issue was originally
discovered by Murray McAllister with this simple POC (if the following
is executed by an unprivileged user it will instantly panic the system):
int main(void) {
int fd, ret;
unsigned int buffer[10000];
When checking the file name attribute, we want to ensure that it fits
within the bounds of ATTR_RECORD. To do this, we should check that (attr
record + file name offset + file name length) < (attr record + attr record
length).
However, the original check did not include the file name offset in the
calculation. This means that corrupted on-disk metadata might not caught
by the incorrect file name check, and lead to an invalid memory access.
An example can be seen in the crash report of a memory corruption error
found by Syzbot:
https://syzkaller.appspot.com/bug?id=a1a1e379b225812688566745c3e2f7242bffc246
Adding the file name offset to the validity check fixes this error and
passes the Syzbot reproducer test.
when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.
We got following bug when system resumes from s4:
kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S W 5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c
Creation EP's debugfs called earlier than debugfs folder for dwc3
device created. As result EP's debugfs are created in '/sys/kernel/debug'
instead of '/sys/kernel/debug/usb/dwc3.1.auto'.
Moved dwc3_debugfs_init() function call before calling
dwc3_core_init_mode() to allow create dwc3 debugfs parent before
creating EP's debugfs's.
The device (32a7:0000 Heimann Sensor GmbH USB appset demo) claims to be
a CDC-ACM device in its descriptors but in fact is not. If it is run
with echo disabled it returns garbled data, probably due to something
that happens in the TTY layer. And when run with echo enabled (the
default), it will mess up the calibration data of the sensor the first
time any data is sent to the device.
In short, I had a bad time after connecting the sensor and trying to get
it to work. I hope blacklisting it in the cdc-acm driver will save
someone else a bit of trouble.
when receive eem echo command, it will send a response,
but queue this response to the usb request which allocate
from gadget device endpoint zero,
and transmit the request to IN endpoint of eem interface.
on dwc3 gadget, it will trigger following warning in function
__dwc3_gadget_ep_queue(),
if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
&req->request, req->dep->name))
return -EINVAL;
fix it by allocating a usb request from IN endpoint of eem interface,
and transmit the usb request to same IN endpoint of eem interface.
In ems_usb_disconnect() dev pointer, which is netdev private data, is
used after free_candev() call:
| if (dev) {
| unregister_netdev(dev->netdev);
| free_candev(dev->netdev);
|
| unlink_all_urbs(dev);
|
| usb_free_urb(dev->intr_urb);
|
| kfree(dev->intr_in_buffer);
| kfree(dev->tx_msg_buffer);
| }
Fix it by simply moving free_candev() at the end of the block.
Fail log:
| BUG: KASAN: use-after-free in ems_usb_disconnect
| Read of size 8 at addr ffff88804e041008 by task kworker/1:2/2895
|
| CPU: 1 PID: 2895 Comm: kworker/1:2 Not tainted 5.13.0-rc5+ #164
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.4
| Workqueue: usb_hub_wq hub_event
| Call Trace:
| dump_stack (lib/dump_stack.c:122)
| print_address_description.constprop.0.cold (mm/kasan/report.c:234)
| kasan_report.cold (mm/kasan/report.c:420 mm/kasan/report.c:436)
| ems_usb_disconnect (drivers/net/can/usb/ems_usb.c:683 drivers/net/can/usb/ems_usb.c:1058)
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface") Link: https://lore.kernel.org/r/20210617185130.5834-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the four control requests which erroneously used usb_rcvctrlpipe().
Fixes: 1d3e20236d7a ("[PATCH] USB: usbtouchscreen: unified USB touchscreen driver") Fixes: 24ced062a296 ("usbtouchscreen: add support for DMC TSC-10/25 devices") Fixes: 9e3b25837a20 ("Input: usbtouchscreen - add support for e2i touchscreen controller") Signed-off-by: Johan Hovold <johan@kernel.org> Cc: stable@vger.kernel.org # 2.6.17 Link: https://lore.kernel.org/r/20210524092048.4443-1-johan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Asus Zenbook 14 UM431D has two speaker pins and a headphone pin, and
the auto-parser ends up assigning the bass to the third DAC 0x06.
Although the tone comes out, it's inconvenient because this DAC has no
volume control unlike two other DACs.
For obtaining the volume control for the bass speaker, this patch
enforces the mapping to let both front and bass speaker pins sharing
the same DAC. It's not ideal but a little bit of improvement.
Since we've already applied the same workaround for another ASUS
machine, we just need to hook the chain to the existing quirk.
On HP Spectre x360 15-df0xxx, after system boot with plugged headset, the
headset mic are not detected.
Moving pincfg and DAC's config to single fixup function fix this.
[ The actual bug in the original code was that it used a chain to
ALC286_FIXUP_SPEAKER2_TO_DAC1, and it contains not only the DAC1
route fix but also another chain to ALC269_FIXUP_THINKPAD_ACPI.
I thought the latter one is harmless for non-Thinkpad, but it
doesn't seem so; it contains again yet another chain to
ALC269_FIXUP_SKI_IGNORE, and this might be bad for some machines,
including this HP machine. -- tiwai ]
The recent workaround for the wild interrupts in commit c1f0616124c4
("ALSA: intel8x0: Don't update period unless prepared") leaded to a
regression, causing the interrupt storm during ac97 clock measurement
at the driver probe. We need to handle the interrupt while the clock
measurement as well as the proper PCM streams.
The current way of the scarlett2 mixer code managing the
usb_mixer_elem_info object is wrong in two ways: it passes its
internal index to the head.id field, and the val_type field is
uninitialized. This ended up with the wrong execution at the resume
because a bogus unit id is passed wrongly. Also, in the later code
extensions, we'll have more mixer elements, and passing the index will
overflow the unit id size (of 256).
This patch corrects those issues. It introduces a new value type,
USB_MIXER_BESPOKEN, which indicates a non-standard mixer element, and
use this type for all scarlett2 mixer elements, as well as
initializing the fixed unit id 0 for avoiding the overflow.
At extending the available mixer values for 32bit types, we forgot to
add the corresponding entries for the format dump in the proc output.
This may result in OOB access. Here adds the missing entries.
In order to avoid a race condition for user events when changing
cpu affinity reset the active flag only when EOI-ing the event.
This is working fine as all user events are lateeoi events. Note that
lateeoi_ack_mask_dynirq() is not modified as there is no explicit call
to xen_irq_lateeoi() expected later.
Cc: stable@vger.kernel.org Reported-by: Julien Grall <julien@xen.org> Fixes: b6622798bc50b62 ("xen/events: avoid handling the same event on two cpus at the same time") Tested-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrvsky@oracle.com> Link: https://lore.kernel.org/r/20210623130913.9405-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Send SEV_CMD_DECOMMISSION command to PSP firmware if ASID binding
fails. If a failure happens after a successful LAUNCH_START command,
a decommission command should be executed. Otherwise, guest context
will be unfreed inside the AMD SP. After the firmware will not have
memory to allocate more SEV guest context, LAUNCH_START command will
begin to fail with SEV_RET_RESOURCE_LIMIT error.
The existing code calls decommission inside sev_unbind_asid, but it is
not called if a failure happens before guest activation succeeds. If
sev_bind_asid fails, decommission is never called. PSP firmware has a
limit for the number of guests. If sev_asid_binding fails many times,
PSP firmware will not have resources to create another guest context.
Cc: stable@vger.kernel.org Fixes: 59414c989220 ("KVM: SVM: Add support for KVM_SEV_LAUNCH_START command") Reported-by: Peter Gonda <pgonda@google.com> Signed-off-by: Alper Gun <alpergun@google.com> Reviewed-by: Marc Orr <marcorr@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210610174604.2554090-1-alpergun@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CALL_ON_STACK macro is used to call a C function from inline
assembly, and therefore must consider the C ABI, which says that only
registers 6-13, and 15 are non-volatile (restored by the called
function).
The inline assembly incorrectly marks all registers used to pass
parameters to the called function as read-only input operands, instead
of operands that are read and written to. This might result in
register corruption depending on usage, compiler, and compile options.
Fix this by marking all operands used to pass parameters as read/write
operands. To keep the code simple even register 6, if used, is marked
as read-write operand.
There may be many encrypted regions that need to be unregistered when a
SEV VM is destroyed. This can lead to soft lockups. For example, on a
host running 4.15:
Although the CLFLUSH is no longer issued on every encrypted region to be
unregistered, there are no other changes that can prevent soft lockups for
very large SEV VMs in the latest kernel.
Periodically schedule if necessary. This still holds kvm->lock across the
resched, but since this only happens when the VM is destroyed this is
assumed to be acceptable.
Allow creating FDB steering rules only when in switchdev mode.
The only software model where a userspace application can manipulate
FDB entries is when it manages the eswitch. This is only possible in
switchdev mode where we expose a single RDMA device with representors
for all the vports that are connected to the eswitch.
Fixes: 52438be44112 ("RDMA/mlx5: Allow inserting a steering rule to the FDB") Link: https://lore.kernel.org/r/e928ae7c58d07f104716a2a8d730963d1bd01204.1623052923.git.leonro@nvidia.com Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
[sudip: manually backport to old file] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both of these drivers use ioport_map(), so they need to
depend on HAS_IOPORT_MAP. Otherwise, they cannot be built
even with COMPILE_TEST on architectures without an ioport
implementation, such as ARCH=um.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Handle a reported media event code of 3. This indicates that the media has
been removed from the drive and user intervention is required to proceed.
Return DISK_EVENT_EJECT_REQUEST in that case.
The Secure Boot Forbidden Signature Database, dbx, contains a list of now
revoked signatures and keys previously approved to boot with UEFI Secure
Boot enabled. The dbx is capable of containing any number of
EFI_CERT_X509_SHA256_GUID, EFI_CERT_SHA256_GUID, and EFI_CERT_X509_GUID
entries.
Currently when EFI_CERT_X509_GUID are contained in the dbx, the entries are
skipped.
Add support for EFI_CERT_X509_GUID dbx entries. When a EFI_CERT_X509_GUID
is found, it is added as an asymmetrical key to the .blacklist keyring.
Anytime the .platform keyring is used, the keys in the .blacklist keyring
are referenced, if a matching key is found, the key will be rejected.
[DH: Made the following changes:
- Added to have a config option to enable the facility. This allows a
Kconfig solution to make sure that pkcs7_validate_trust() is
enabled.[1][2]
- Moved the functions out from the middle of the blacklist functions.
- Added kerneldoc comments.]
The handlers to add the keys to the .platform keyring and blacklisted
hashes to the .blacklist keyring is common for both the uefi and powerpc
mechanisms of loading the keys/hashes from the firmware.
This patch moves the common code from load_uefi.c to keyring_handler.c
If more than one futex is placed on a shmem huge page, it can happen
that waking the second wakes the first instead, and leaves the second
waiting: the key's shared.pgoff is wrong.
When 3.11 commit 13d60f4b6ab5 ("futex: Take hugepages into account when
generating futex_key"), the only shared huge pages came from hugetlbfs,
and the code added to deal with its exceptional page->index was put into
hugetlb source. Then that was missed when 4.8 added shmem huge pages.
page_to_pgoff() is what others use for this nowadays: except that, as
currently written, it gives the right answer on hugetlbfs head, but
nonsense on hugetlbfs tails. Fix that by calling hugetlbfs-specific
hugetlb_basepage_index() on PageHuge tails as well as on head.
Yes, it's unconventional to declare hugetlb_basepage_index() there in
pagemap.h, rather than in hugetlb.h; but I do not expect anything but
page_to_pgoff() ever to need it.
[akpm@linux-foundation.org: give hugetlb_basepage_index() prototype the correct scope]
Link: https://lkml.kernel.org/r/b17d946b-d09-326e-b42a-52884c36df32@google.com Fixes: 800d8c63b2e9 ("shmem: add huge pages support") Reported-by: Neel Natu <neelnatu@google.com> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Zhang Yi <wetpzy@gmail.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Darren Hart <dvhart@infradead.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note on stable backport: leave redundant #include <linux/hugetlb.h>
in kernel/futex.c, to avoid conflict over the header files included.
Hugh Dickins [Fri, 25 Jun 2021 01:39:30 +0000 (18:39 -0700)]
mm/thp: another PVMW_SYNC fix in page_vma_mapped_walk()
Aha! Shouldn't that quick scan over pte_none()s make sure that it holds
ptlock in the PVMW_SYNC case? That too might have been responsible for
BUGs or WARNs in split_huge_page_to_list() or its unmap_page(), though
I've never seen any.
Link: https://lkml.kernel.org/r/1bdf384c-8137-a149-2a1e-475a4791c3c@google.com Link: https://lore.kernel.org/linux-mm/20210412180659.B9E3.409509F4@e16-tech.com/ Fixes: ace71a19cec5 ("mm: introduce page_vma_mapped_walk()") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Tested-by: Wang Yugui <wangyugui@e16-tech.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Xu <peterx@redhat.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Zi Yan <ziy@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hugh Dickins [Fri, 25 Jun 2021 01:39:26 +0000 (18:39 -0700)]
mm/thp: fix page_vma_mapped_walk() if THP mapped by ptes
Running certain tests with a DEBUG_VM kernel would crash within hours,
on the total_mapcount BUG() in split_huge_page_to_list(), while trying
to free up some memory by punching a hole in a shmem huge page: split's
try_to_unmap() was unable to find all the mappings of the page (which,
on a !DEBUG_VM kernel, would then keep the huge page pinned in memory).
Crash dumps showed two tail pages of a shmem huge page remained mapped
by pte: ptes in a non-huge-aligned vma of a gVisor process, at the end
of a long unmapped range; and no page table had yet been allocated for
the head of the huge page to be mapped into.
Although designed to handle these odd misaligned huge-page-mapped-by-pte
cases, page_vma_mapped_walk() falls short by returning false prematurely
when !pmd_present or !pud_present or !p4d_present or !pgd_present: there
are cases when a huge page may span the boundary, with ptes present in
the next.
Restructure page_vma_mapped_walk() as a loop to continue in these cases,
while keeping its layout much as before. Add a step_forward() helper to
advance pvmw->address across those boundaries: originally I tried to use
mm's standard p?d_addr_end() macros, but hit the same crash 512 times
less often: because of the way redundant levels are folded together, but
folded differently in different configurations, it was just too
difficult to use them correctly; and step_forward() is simpler anyway.
Link: https://lkml.kernel.org/r/fedb8632-1798-de42-f39e-873551d5bc81@google.com Fixes: ace71a19cec5 ("mm: introduce page_vma_mapped_walk()") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Xu <peterx@redhat.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Wang Yugui <wangyugui@e16-tech.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Zi Yan <ziy@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hugh Dickins [Fri, 25 Jun 2021 01:39:17 +0000 (18:39 -0700)]
mm: page_vma_mapped_walk(): add a level of indentation
page_vma_mapped_walk() cleanup: add a level of indentation to much of
the body, making no functional change in this commit, but reducing the
later diff when this is all converted to a loop.
[hughd@google.com: : page_vma_mapped_walk(): add a level of indentation fix] Link: https://lkml.kernel.org/r/7f817555-3ce1-c785-e438-87d8efdcaf26@google.com Link: https://lkml.kernel.org/r/efde211-f3e2-fe54-977-ef481419e7f3@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Xu <peterx@redhat.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Wang Yugui <wangyugui@e16-tech.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Zi Yan <ziy@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log