Linus Torvalds [Thu, 3 Dec 2020 21:10:11 +0000 (13:10 -0800)]
Merge tag 'net-5.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc7, including fixes from bpf, netfilter,
wireless drivers, wireless mesh and can.
Current release - regressions:
- mt76: usb: fix crash on device removal
Current release - always broken:
- xsk: Fix umem cleanup from wrong context in socket destruct
Previous release - regressions:
- net: ip6_gre: set dev->hard_header_len when using header_ops
* tag 'net-5.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
net/mlx5: DR, Proper handling of unsupported Connect-X6DX SW steering
net/mlx5e: kTLS, Enforce HW TX csum offload with kTLS
net: mlx5e: fix fs_tcp.c build when IPV6 is not enabled
net/mlx5: Fix wrong address reclaim when command interface is down
net/sched: act_mpls: ensure LSE is pullable before reading it
net: openvswitch: ensure LSE is pullable before reading it
net: skbuff: ensure LSE is pullable before decrementing the MPLS ttl
net: mvpp2: Fix error return code in mvpp2_open()
chelsio/chtls: fix a double free in chtls_setkey()
rtw88: debug: Fix uninitialized memory in debugfs code
vxlan: fix error return code in __vxlan_dev_create()
net: pasemi: fix error return code in pasemi_mac_open()
cxgb3: fix error return code in t3_sge_alloc_qset()
net/x25: prevent a couple of overflows
dpaa_eth: copy timestamp fields to new skb in A-050385 workaround
net: ip6_gre: set dev->hard_header_len when using header_ops
mt76: usb: fix crash on device removal
iwlwifi: pcie: add some missing entries for AX210
iwlwifi: pcie: invert values of NO_160 device config entries
iwlwifi: pcie: add one missing entry for AX210
...
====================
mptcp: reject invalid mp_join requests right away
At the moment MPTCP can detect an invalid join request (invalid token,
max number of subflows reached, and so on) right away but cannot reject
the connection until the 3WHS has completed.
Instead the connection will complete and the subflow is reset afterwards.
To send the reset most information is already available, but we don't have
good spot where the reset could be sent:
1. The ->init_req callback is too early and also doesn't allow to return an
error that could be used to inform the TCP stack that the SYN should be
dropped.
2. The ->route_req callback lacks the skb needed to send a reset.
3. The ->send_synack callback is the best fit from the available hooks,
but its called after the request socket has been inserted into the queue
already. This means we'd have to remove it again right away.
From a technical point of view, the second hook would be best:
1. Its before insertion into listener queue.
2. If it returns NULL TCP will drop the packet for us.
Problem is that we'd have to pass the skb to the function just for MPTCP.
Paolo suggested to merge init_req and route_req callbacks instead:
This makes all info available to MPTCP -- a return value of NULL drops the
packet and MPTCP can send the reset if needed.
Because 'route_req' has a 'const struct sock *', this means either removal
of const qualifier, or a bit of code churn to pass 'const' in security land.
This does the latter; I did not find any spots that need write access to struct
sock.
To recap, the two alternatives are:
1. Solve it entirely in MPTCP: use the ->send_synack callback to
unlink the request socket from the listener & drop it.
2. Avoid 'security' churn by removing the const qualifier.
====================
Florian Westphal [Mon, 30 Nov 2020 15:36:31 +0000 (16:36 +0100)]
mptcp: emit tcp reset when a join request fails
RFC 8684 says:
If the token is unknown or the host wants to refuse subflow establishment
(for example, due to a limit on the number of subflows it will permit),
the receiver will send back a reset (RST) signal, analogous to an unknown
port in TCP, containing an MP_TCPRST option (Section 3.6) with an
"MPTCP specific error" reason code.
mptcp-next doesn't support MP_TCPRST yet, this can be added in another
change.
Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal [Mon, 30 Nov 2020 15:36:30 +0000 (16:36 +0100)]
tcp: merge 'init_req' and 'route_req' functions
The Multipath-TCP standard (RFC 8684) says that an MPTCP host should send
a TCP reset if the token in a MP_JOIN request is unknown.
At this time we don't do this, the 3whs completes and the 'new subflow'
is reset afterwards. There are two ways to allow MPTCP to send the
reset.
1. override 'send_synack' callback and emit the rst from there.
The drawback is that the request socket gets inserted into the
listeners queue just to get removed again right away.
2. Send the reset from the 'route_req' function instead.
This avoids the 'add&remove request socket', but route_req lacks the
skb that is required to send the TCP reset.
Instead of just adding the skb to that function for MPTCP sake alone,
Paolo suggested to merge init_req and route_req functions.
This saves one indirection from syn processing path and provides the skb
to the merged function at the same time.
'send reset on unknown mptcp join token' is added in next patch.
Suggested-by: Paolo Abeni <pabeni@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal [Mon, 30 Nov 2020 15:36:29 +0000 (16:36 +0100)]
security: add const qualifier to struct sock in various places
A followup change to tcp_request_sock_op would have to drop the 'const'
qualifier from the 'route_req' function as the
'security_inet_conn_request' call is moved there - and that function
expects a 'struct sock *'.
However, it turns out its also possible to add a const qualifier to
security_inet_conn_request instead.
Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: James Morris <jamorris@linux.microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 3 Dec 2020 19:58:26 +0000 (11:58 -0800)]
Merge tag 's390-5.10-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
"One commit is fixing lockdep irq state tracing which broke with -rc6.
The other one fixes logical vs physical CPU address mixup in our PCI
code.
Summary:
- fix lockdep irq state tracing
- fix logical vs physical CPU address confusion in PCI code"
* tag 's390-5.10-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix irq state tracing
s390/pci: fix CPU address in MSI for directed IRQ
Yevgeny Kliteynik [Thu, 3 Dec 2020 04:39:46 +0000 (20:39 -0800)]
net/mlx5: DR, Proper handling of unsupported Connect-X6DX SW steering
STEs format for Connect-X5 and Connect-X6DX different. Currently, on
Connext-X6DX the SW steering would break at some point when building STEs
w/o giving a proper error message. Fix this by checking the STE format of
the current device when initializing domain: add mlx5_ifc definitions for
Connect-X6DX SW steering, read FW capability to get the current format
version, and check this version when domain is being created.
Tariq Toukan [Thu, 3 Dec 2020 04:39:45 +0000 (20:39 -0800)]
net/mlx5e: kTLS, Enforce HW TX csum offload with kTLS
Checksum calculation cannot be done in SW for TX kTLS HW offloaded
packets.
Offload it to the device, disregard the declared state of the TX
csum offload feature.
Randy Dunlap [Thu, 3 Dec 2020 04:39:44 +0000 (20:39 -0800)]
net: mlx5e: fix fs_tcp.c build when IPV6 is not enabled
Fix build when CONFIG_IPV6 is not enabled by making a function
be built conditionally.
Fixes these build errors and warnings:
../drivers/net/ethernet/mellanox/mlx5/core/en_accel/fs_tcp.c: In function 'accel_fs_tcp_set_ipv6_flow':
../include/net/sock.h:380:34: error: 'struct sock_common' has no member named 'skc_v6_daddr'; did you mean 'skc_daddr'?
380 | #define sk_v6_daddr __sk_common.skc_v6_daddr
| ^~~~~~~~~~~~
../drivers/net/ethernet/mellanox/mlx5/core/en_accel/fs_tcp.c:55:14: note: in expansion of macro 'sk_v6_daddr'
55 | &sk->sk_v6_daddr, 16);
| ^~~~~~~~~~~
At top level:
../drivers/net/ethernet/mellanox/mlx5/core/en_accel/fs_tcp.c:47:13: warning: 'accel_fs_tcp_set_ipv6_flow' defined but not used [-Wunused-function]
47 | static void accel_fs_tcp_set_ipv6_flow(struct mlx5_flow_spec *spec, struct sock *sk)
Fixes: 5229a96e59ec ("net/mlx5e: Accel, Expose flow steering API for rules add/del") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eran Ben Elisha [Thu, 3 Dec 2020 04:39:43 +0000 (20:39 -0800)]
net/mlx5: Fix wrong address reclaim when command interface is down
When command interface is down, driver to reclaim all 4K page chucks that
were hold by the Firmeware. Fix a bug for 64K page size systems, where
driver repeatedly released only the first chunk of the page.
Define helper function to fill 4K chunks for a given Firmware pages.
Iterate over all unreleased Firmware pages and call the hepler per each.
Fixes: 5adff6a08862 ("net/mlx5: Fix incorrect page count when in internal error") Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Davide Caratti [Thu, 3 Dec 2020 09:37:52 +0000 (10:37 +0100)]
net/sched: act_mpls: ensure LSE is pullable before reading it
when 'act_mpls' is used to mangle the LSE, the current value is read from
the packet dereferencing 4 bytes at mpls_hdr(): ensure that the label is
contained in the skb "linear" area.
Found by code inspection.
v2:
- use MPLS_HLEN instead of sizeof(new_lse), thanks to Jakub Kicinski
Davide Caratti [Thu, 3 Dec 2020 09:46:06 +0000 (10:46 +0100)]
net: openvswitch: ensure LSE is pullable before reading it
when openvswitch is configured to mangle the LSE, the current value is
read from the packet dereferencing 4 bytes at mpls_hdr(): ensure that
the label is contained in the skb "linear" area.
Davide Caratti [Thu, 3 Dec 2020 09:58:21 +0000 (10:58 +0100)]
net: skbuff: ensure LSE is pullable before decrementing the MPLS ttl
skb_mpls_dec_ttl() reads the LSE without ensuring that it is contained in
the skb "linear" area. Fix this calling pskb_may_pull() before reading the
current ttl.
Wang Hai [Thu, 3 Dec 2020 14:18:06 +0000 (22:18 +0800)]
net: mvpp2: Fix error return code in mvpp2_open()
Fix to return negative error code -ENOENT from invalid configuration
error handling case instead of 0, as done elsewhere in this function.
Fixes: 4bb043262878 ("net: mvpp2: phylink support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20201203141806.37966-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Thu, 3 Dec 2020 08:44:31 +0000 (11:44 +0300)]
chelsio/chtls: fix a double free in chtls_setkey()
The "skb" is freed by the transmit code in cxgb4_ofld_send() and we
shouldn't use it again. But in the current code, if we hit an error
later on in the function then the clean up code will call kfree_skb(skb)
and so it causes a double free.
Set the "skb" to NULL and that makes the kfree_skb() a no-op.
Fixes: d25f2f71f653 ("crypto: chtls - Program the TLS session Key") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/X8ilb6PtBRLWiSHp@mwanda Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Uwe Kleine-König [Thu, 3 Dec 2020 08:41:42 +0000 (09:41 +0100)]
pwm: sl28cpld: fix getting driver data in pwm callbacks
Currently .get_state() and .apply() use dev_get_drvdata() on the struct
device related to the pwm chip. This only works after .probe() called
platform_set_drvdata() which in this driver happens only after
pwmchip_add() and so comes possibly too late.
Instead of setting the driver data earlier use the traditional
container_of approach as this way the driver data is conceptually and
computational nearer.
Fixes: 9db33d221efc ("pwm: Add support for sl28cpld PWM controller") Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Willy Tarreau [Mon, 30 Nov 2020 07:36:48 +0000 (08:36 +0100)]
lib/syscall: fix syscall registers retrieval on 32-bit platforms
Lilith >_> and Claudio Bozzato of Cisco Talos security team reported
that collect_syscall() improperly casts the syscall registers to 64-bit
values leaking the uninitialized last 24 bytes on 32-bit platforms, that
are visible in /proc/self/syscall.
The cause is that info->data.args are u64 while syscall_get_arguments()
uses longs, as hinted by the bogus pointer cast in the function.
Let's just proceed like the other call places, by retrieving the
registers into an array of longs before assigning them to the caller's
array. This was successfully tested on x86_64, i386 and ppc32.
Thomas Karlsson [Wed, 2 Dec 2020 18:49:58 +0000 (19:49 +0100)]
macvlan: Support for high multicast packet rate
Background:
Broadcast and multicast packages are enqueued for later processing.
This queue was previously hardcoded to 1000.
This proved insufficient for handling very high packet rates.
This resulted in packet drops for multicast.
While at the same time unicast worked fine.
The change:
This patch make the queue length adjustable to accommodate
for environments with very high multicast packet rate.
But still keeps the default value of 1000 unless specified.
The queue length is specified as a request per macvlan
using the IFLA_MACVLAN_BC_QUEUE_LEN parameter.
The actual used queue length will then be the maximum of
any macvlan connected to the same port. The actual used
queue length for the port can be retrieved (read only)
by the IFLA_MACVLAN_BC_QUEUE_LEN_USED parameter for verification.
This will be followed up by a patch to iproute2
in order to adjust the parameter from userspace.
Dan Carpenter [Thu, 3 Dec 2020 08:43:37 +0000 (11:43 +0300)]
rtw88: debug: Fix uninitialized memory in debugfs code
This code does not ensure that the whole buffer is initialized and none
of the callers check for errors so potentially none of the buffer is
initialized. Add a memset to eliminate this bug.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/X8ilOfVz3pf0T5ec@mwanda
====================
nfc: s3fwrn5: Support a UART interface
S3FWRN82 is the Samsung's NFC chip that supports the UART communication.
Before adding the UART driver module, I did refactoring the s3fwrn5_i2c
module to reuse the common blocks.
====================
Jakub Kicinski [Thu, 3 Dec 2020 01:28:36 +0000 (17:28 -0800)]
Merge tag 'mlx5-next-2020-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next-2020-12-02
Low level mlx5 updates required by both netdev and rdma trees.
* tag 'mlx5-next-2020-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Treat host PF vport as other (non eswitch manager) vport
net/mlx5: Enable host PF HCA after eswitch is initialized
net/mlx5: Rename peer_pf to host_pf
net/mlx5: Make API mlx5_core_is_ecpf accept const pointer
net/mlx5: Export steering related functions
net/mlx5: Expose other function ifc bits
net/mlx5: Expose IP-in-IP TX and RX capability bits
net/mlx5: Update the hardware interface definition for vhca state
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Avoid exposing driver internal command helpers
net/mlx5: Add ts_cqe_to_dest_cqn related bits
net/mlx5: Add misc4 to mlx5_ifc_fte_match_param_bits
net/mlx5: Check dr mask size against mlx5_match_param size
net/mlx5: Add sampler destination type
net/mlx5: Add sample offload hardware bits and structures
====================
Dan Carpenter [Tue, 1 Dec 2020 15:15:12 +0000 (18:15 +0300)]
net/x25: prevent a couple of overflows
The .x25_addr[] address comes from the user and is not necessarily
NUL terminated. This leads to a couple problems. The first problem is
that the strlen() in x25_bind() can read beyond the end of the buffer.
The second problem is more subtle and could result in memory corruption.
The call tree is:
x25_connect()
--> x25_write_internal()
--> x25_addr_aton()
The .x25_addr[] buffers are copied to the "addresses" buffer from
x25_write_internal() so it will lead to stack corruption.
Verify that the strings are NUL terminated and return -EINVAL if they
are not.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: a9288525d2ae ("X25: Dont let x25_bind use addresses containing characters") Reported-by: "kiyin(尹亮)" <kiyin@tencent.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Martin Schiller <ms@dev.tdt.de> Link: https://lore.kernel.org/r/X8ZeAKm8FnFpN//B@mwanda Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 3 Dec 2020 01:25:23 +0000 (17:25 -0800)]
Merge tag 'gfs2-v5.10-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fixes from Andreas Gruenbacher:
"Various gfs2 fixes"
* tag 'gfs2-v5.10-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix deadlock between gfs2_{create_inode,inode_lookup} and delete_work_func
gfs2: Upgrade shared glocks for atime updates
gfs2: Don't freeze the file system during unmount
gfs2: check for empty rgrp tree in gfs2_ri_update
gfs2: set lockdep subclass for iopen glocks
gfs2: Fix deadlock dumping resource group glocks
====================
net: dsa: microchip: make ksz8795 driver more versatile
This series changes the ksz8795 driver to use more dynamic variables
instead of static defines. The purpose is to prepare the driver to
be used with other microchip switches with a similar layout.
====================
Michael Grzeschik [Tue, 1 Dec 2020 20:45:06 +0000 (21:45 +0100)]
net: dsa: microchip: ksz8795: use num_vlans where possible
The value of the define VLAN_TABLE_ENTRIES can be derived from
num_vlans. This patch is using the variable num_vlans instead and
removes the extra define.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Grzeschik [Tue, 1 Dec 2020 20:45:05 +0000 (21:45 +0100)]
net: dsa: microchip: ksz8795: use port_cnt instead of TOTOAL_PORT_NUM
To get the driver working with other chips using different port counts
the dyn_mac_table should be flushed depending on the amount of available
ports. This patch remove the extra define TOTOAL_PORT_NUM and is
making use of the dynamic port_cnt variable instead.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Grzeschik [Tue, 1 Dec 2020 20:45:03 +0000 (21:45 +0100)]
net: dsa: microchip: ksz8795: align port_cnt usage with other microchip drivers
The ksz8795 driver is using port_cnt differently to the other microchip
DSA drivers. It sets it to the external physical port count, than the
whole port count (including the cpu port). This patch is aligning the
variables purpose with the other microchip drivers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable num_ports is already assigned in the init function. The
drivers individual init function already handles the different purpose
of port_cnt vs port_cnt + 1. This patch removes the extra assignment of
the variable.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Grzeschik [Tue, 1 Dec 2020 20:45:01 +0000 (21:45 +0100)]
net: dsa: microchip: ksz8795: use phy_port_cnt where possible
The driver is currently hard coded to SWITCH_PORT_NUM being
(TOTAL_PORT_NUM - 1) which is limited to 4 user ports for the ksz8795.
The phy_port_cnt is referring to its user ports. The patch removes the
extra define and use the assigned variable phy_port_cnt instead so the
driver can be used on different switches.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Grzeschik [Tue, 1 Dec 2020 20:45:00 +0000 (21:45 +0100)]
net: dsa: microchip: ksz8795: use mib_cnt where possible
The variable mib_cnt is assigned with TOTAL_SWITCH_COUNTER_NUM. This
value can also be derived from the array size of mib_names. This patch
uses this calculated value instead, removes the extra define and uses
mib_cnt everywhere possible instead of the static define
TOTAL_SWITCH_COUNTER_NUM. Keeping it in a separate variable instead of
using ARRAY_SIZE everywhere instead makes the driver more flexible for
future use of devices with different amount of counters.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Grzeschik [Tue, 1 Dec 2020 20:44:59 +0000 (21:44 +0100)]
net: dsa: microchip: ksz8795: use reg_mib_cnt where possible
The extra define SWITCH_COUNTER_NUM is a copy of the KSZ8795_COUNTER_NUM
define. This patch initializes reg_mib_cnt with KSZ8795_COUNTER_NUM,
makes use of reg_mib_cnt everywhere instead and removes the extra
define.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Grzeschik [Tue, 1 Dec 2020 20:44:58 +0000 (21:44 +0100)]
net: dsa: microchip: ksz8795: move variable assignments from detect to init
This patch moves all variable assignments to the init function. It
leaves the detect function for its single purpose to detect which chip
version is found.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 2 Dec 2020 20:27:37 +0000 (12:27 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"I'm sad to say that we've got an unusually large arm64 fixes pull for
rc7 which addresses numerous significant instrumentation issues with
our entry code.
Without these patches, lockdep is hopelessly unreliable in some
configurations [1,2] and syzkaller is therefore not a lot of use
because it's so noisy.
Although much of this has always been broken, it appears to have been
exposed more readily by other changes such as 044d0d6de9f5 ("lockdep:
Only trace IRQ edges") and general lockdep improvements around IRQ
tracing and NMIs.
Fixing this properly required moving much of the instrumentation hooks
from our entry assembly into C, which Mark has been working on for the
last few weeks. We're not quite ready to move to the recently added
generic functions yet, but the code here has been deliberately written
to mimic that closely so we can look at cleaning things up once we
have a bit more breathing room.
Having said all that, the second version of these patches was posted
last week and I pushed it into our CI (kernelci and cki) along with a
commit which forced on PROVE_LOCKING, NOHZ_FULL and
CONTEXT_TRACKING_FORCE. The result? We found a real bug in the
md/raid10 code [3].
Oh, and there's also a really silly typo patch that's unrelated.
Summary:
- Fix numerous issues with instrumentation and exception entry
- Fix hideous typo in unused register field definition"
Linus Torvalds [Wed, 2 Dec 2020 20:14:03 +0000 (12:14 -0800)]
Merge tag 'sound-5.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are the pending sound fixes for 5.10: all small device-specific
fixes, and nothing particular stands out, so far"
* tag 'sound-5.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add mute LED quirk to yet another HP x360 model
ALSA: hda/realtek: Fix bass speaker DAC assignment on Asus Zephyrus G14
ALSA: hda/generic: Add option to enforce preferred_dacs pairs
ALSA: usb-audio: US16x08: fix value count for level meters
ALSA: hda/realtek - Add new codec supported for ALC897
ASoC: rt5682: change SAR voltage threshold
ASoC: wm_adsp: fix error return code in wm_adsp_load()
ALSA: hda/realtek: Enable headset of ASUS UX482EG & B9400CEA with ALC294
ASoC: qcom: Fix enabling BCLK and LRCLK in LPAIF invalid state
ALSA: hda/realtek - Fixed Dell AIO wrong sound tone
ASoC: Intel: bytcr_rt5640: Fix HP Pavilion x2 Detachable quirks
Linus Torvalds [Wed, 2 Dec 2020 20:09:36 +0000 (12:09 -0800)]
Merge tag 'trace-v5.10-rc6-bootconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull bootconfig fixes from Steven Rostedt:
"Have bootconfig size and checksum be little endian
In case the bootconfig is created on one kind of endian machine, and
then read on the other kind of endian kernel, the size and checksum
will be incorrect. Instead, have both the size and checksum always be
little endian and have the tool and the kernel convert it from little
endian to or from the host endian"
* tag 'trace-v5.10-rc6-bootconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
docs: bootconfig: Add the endianness of fields
tools/bootconfig: Store size and checksum in footer as le32
bootconfig: Load size and checksum in the footer as le32
Eric Dumazet [Wed, 2 Dec 2020 17:16:57 +0000 (09:16 -0800)]
mptcp: avoid potential infinite loop in mptcp_recvmsg()
If a packet is ready in receive queue, and application isssues
a recvmsg()/recvfrom()/recvmmsg() request asking for zero bytes,
we hang in mptcp_recvmsg().
Fixes: ea4ca586b16f ("mptcp: refine MPTCP-level ack scheduling") Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Link: https://lore.kernel.org/r/20201202171657.1185108-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Wed, 2 Dec 2020 06:57:02 +0000 (09:57 +0300)]
octeontx2-af: debugfs: delete dead code
These debugfs never return NULL so all this code will never be run.
In the normal case, (and in this case particularly), the debugfs
functions are not supposed to be checked for errors so all this error
checking code can be safely deleted.
Frieder Schrempf [Tue, 1 Dec 2020 11:39:09 +0000 (12:39 +0100)]
NFC: nxp-nci: Make firmware GPIO pin optional
There are other NXP NCI compatible NFC controllers such as the PN7150
that use an integrated firmware and therefore do not have a GPIO to
select firmware downloading mode. To support this kind of controller,
let's make the firmware GPIO optional.
Antoine Tenart [Mon, 30 Nov 2020 16:19:11 +0000 (17:19 +0100)]
net: ip6_gre: set dev->hard_header_len when using header_ops
syzkaller managed to crash the kernel using an NBMA ip6gre interface. I
could reproduce it creating an NBMA ip6gre interface and forwarding
traffic to it:
skbuff: skb_under_panic: text:ffffffff8250e927 len:148 put:44 head:ffff8c03c7a33
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:109!
Call Trace:
skb_push+0x10/0x10
ip6gre_header+0x47/0x1b0
neigh_connected_output+0xae/0xf0
ip6gre tunnel provides its own header_ops->create, and sets it
conditionally when initializing the tunnel in NBMA mode. When
header_ops->create is used, dev->hard_header_len should reflect the
length of the header created. Otherwise, when not used,
dev->needed_headroom should be used.
Fixes: eb95f52fc72d ("net: ipv6_gre: Fix GRO to work on IPv6 over GRE tap") Cc: Maria Pasechnik <mariap@mellanox.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Link: https://lore.kernel.org/r/20201130161911.464106-1-atenart@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix that by adding while loop again. We need loop, not just single
check, to clean all pending entries.
Additionally move mt76_worker_disable/enable after !mt76_has_tx_pending()
as we want to tx_worker to run to process tx queues, while we wait for
exactly that.
I was a bit worried about accessing q->queued without lock, but
mt76_worker_disable() -> kthread_park() should assure this value will
be seen updated on other cpus.
Fixes: fe5b5ab52e9d ("mt76: unify queue tx cleanup code") Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201126125520.72912-1-stf_xl@wp.pl
Luca Coelho [Wed, 2 Dec 2020 12:41:50 +0000 (14:41 +0200)]
iwlwifi: pcie: invert values of NO_160 device config entries
The NO_160 flag specifies if the device doesn't have 160 MHz support,
but we errorneously assumed the opposite. If the flag was set, we
were considering that 160 MHz was supported, but it's actually the
opposite. Fix it by inverting the bits, i.e. NO_160 is 0x1 and 160
is 0x0.
Johannes Berg [Sun, 29 Nov 2020 13:14:38 +0000 (15:14 +0200)]
iwlwifi: update MAINTAINERS entry
Reflect the fact that the linuxwifi@intel.com address will disappear,
and that neither Emmanuel nor myself are really much involved with
the maintenance these days.
Heiko Carstens [Wed, 2 Dec 2020 10:46:01 +0000 (11:46 +0100)]
s390: fix irq state tracing
With commit 58c644ba512c ("sched/idle: Fix arch_cpu_idle() vs
tracing") common code calls arch_cpu_idle() with a lockdep state that
tells irqs are on.
This doesn't work very well for s390: psw_idle() will enable interrupts
to wait for an interrupt. As soon as an interrupt occurs the interrupt
handler will verify if the old context was psw_idle(). If that is the
case the interrupt enablement bits in the old program status word will
be cleared.
A subsequent test in both the external as well as the io interrupt
handler checks if in the old context interrupts were enabled. Due to
the above patching of the old program status word it is assumed the
old context had interrupts disabled, and therefore a call to
TRACE_IRQS_OFF (aka trace_hardirqs_off_caller) is skipped. Which in
turn makes lockdep incorrectly "think" that interrupts are enabled
within the interrupt handler.
Fix this by unconditionally calling TRACE_IRQS_OFF when entering
interrupt handlers. Also call unconditionally TRACE_IRQS_ON when
leaving interrupts handlers.
This leaves the special psw_idle() case, which now returns with
interrupts disabled, but has an "irqs on" lockdep state. So callers of
psw_idle() must adjust the state on their own, if required. This is
currently only __udelay_disabled().
Fixes: 58c644ba512c ("sched/idle: Fix arch_cpu_idle() vs tracing") Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Gordeev [Thu, 26 Nov 2020 17:00:37 +0000 (18:00 +0100)]
s390/pci: fix CPU address in MSI for directed IRQ
The directed MSIs are delivered to CPUs whose address is
written to the MSI message address. The current code assumes
that a CPU logical number (as it is seen by the kernel)
is also the CPU address.
The above assumption is not correct, as the CPU address
is rather the value returned by STAP instruction. That
value does not necessarily match the kernel logical CPU
number.
Fixes: e979ce7bced2 ("s390/pci: provide support for CPU directed interrupts") Cc: <stable@vger.kernel.org> # v5.2+ Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Reviewed-by: Halil Pasic <pasic@linux.ibm.com> Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Randy Dunlap [Sat, 28 Nov 2020 21:39:05 +0000 (13:39 -0800)]
vdpa: mlx5: fix vdpa/vhost dependencies
drivers/vdpa/mlx5/ uses vhost_iotlb*() interfaces, so select
VHOST_IOTLB to make them be built.
However, if VHOST_IOTLB is the only VHOST symbol that is
set/enabled, the object file still won't be built because
drivers/Makefile won't descend into drivers/vhost/ to build it,
so make drivers/Makefile build the needed binary whenever
VHOST_IOTLB is set, like it does for VHOST_RING.
Fixes: 29064bfdabd5 ("vdpa/mlx5: Add support library for mlx5 VDPA implementation") Fixes: aff90770e54c ("vdpa/mlx5: Fix dependency on MLX5_CORE") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Eli Cohen <eli@mellanox.com> Cc: Parav Pandit <parav@mellanox.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: virtualization@lists.linux-foundation.org Cc: Saeed Mahameed <saeedm@nvidia.com> Cc: Leon Romanovsky <leonro@nvidia.com> Cc: netdev@vger.kernel.org Link: https://lore.kernel.org/r/20201128213905.27409-1-rdunlap@infradead.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Heiner Kallweit [Tue, 1 Dec 2020 08:57:29 +0000 (09:57 +0100)]
r8169: set tc_offset only if tally counter reset isn't supported
On chip versions supporting tally counter reset we currently update
the counters after a reset although we know all counters are zero.
Skip this unnecessary step.
====================
net: ipa: IPA v4.5 aggregation and Qtime
This series updates some IPA register definitions that change in
substantive ways for IPA v4.5.
One register defines parameters used by an endpoint to aggregate
multiple packets into a buffer. The size and position of most
fields in that register have changed with this new hardware version,
and consequently the function that programs it needs to be done a
bit differently. The first patch takes care of this.
Second, IPA v4.5 introduces a unified time keeping component to be
used in several places by the IPA hardware. A main clock divider
provides a fundamental tick rate, and several timestamped features
now define their granularity based on that. There is also a set of
"pulse generators" derived from the main tick, and these are used
to implement timers used for aggregation and head-of-line block
avoidance. The second patch adds IPA register updates to support
Qtime along with its configuration, and the last two patches
configure the timers that use it.
====================
Alex Elder [Mon, 30 Nov 2020 23:37:12 +0000 (17:37 -0600)]
net: ipa: use Qtime for IPA v4.5 head-of-line time limit
Extend ipa_reg_init_hol_block_timer_val() so it properly calculates
the head-of-line block timeout to use for IPA v4.5.
Introduce hol_block_timer_qtime_val() to compute the value to use
for IPA v4.5, where Qtime is used as the basis of the timer. Call
that function from hol_block_timer_val() for IPA v4.5.
Both of these are private functions, so shorten their names a bit so
they don't take up so much space on the line.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 30 Nov 2020 23:37:11 +0000 (17:37 -0600)]
net: ipa: use Qtime for IPA v4.5 aggregation time limit
Change aggr_time_limit_encoded() to properly calculate the
aggregation time limit to use for IPA v4.5.
Older IPA versions program the AGGR_GRANULARITY field of the
of the COUNTER_CFG register to set the granularity of the
aggregation timer, which we configure to be 500 microseconds.
Instead, IPA v4.5 selects between two possible granularity values
derived from the 19.2 MHz Qtime clock. These granularities are
100 microseconds or 1 millisecond per tick. We use the smaller
granularity if possible, unless the desired period is too large
to be specified that way.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 30 Nov 2020 23:37:10 +0000 (17:37 -0600)]
net: ipa: set up IPA v4.5 Qtime configuration
IPA v4.5 introduces a new unified timer architecture driven on the
19.2 MHz SoC crystal oscillator (XO). It is independent of the IPA
core clock and avoids some duplication.
Lower-resolution time stamps are derived from this by using only the
high-order bits of the 19.2 MHz Qtime clock. And timers are derived
from this based on "pulse generators" configured to fire at a fixed
rate based on the Qtime clock.
This patch introduces ipa_qtime_config(), which configures the Qtime
mechanism for use. It also adds to the IPA register definitions
related to timers and time stamping.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 30 Nov 2020 23:37:09 +0000 (17:37 -0600)]
net: ipa: update IPA aggregation registers for IPA v4.5
IPA v4.5 significantly changes the format of the configuration
register used for endpoint aggregation. The AGGR_BYTE_LIMIT field
is now larger, and the positions of other fields are shifted. This
complicates the way we have to access this register because functions
like u32_encode_bits() require their field mask argument to be constant.
A further complication is that we want to know the maximum value
representable by at least one of these fields, and that too requires
a constant field mask.
This patch adds support for IPA v4.5 endpoint aggregation registers
in a way that continues to support "legacy" IPA hardware. It does
so in a way that keeps field masks constant.
First, for each variable field mask, we define an inline function
whose return value is either the legacy value or the IPA v4.5 value.
Second, we define functions for these fields that encode a value
to use in each field based on the IPA version (this approach is
already used elsewhere). The field mask provided is supplied by
the function mentioned above.
Finally, for the aggregation byte limit fields where we want to
know the maximum representable value, we define a function that
returns that maximum, computed from the appropriate field mask.
We can no longer verify at build time that our buffer size is
in the range that can be represented by the aggregation byte
limit field. So remove the test done by a BUILD_BUG_ON() call
in ipa_endpoint_validate_build(), and implement a comparable check
at the top of ipa_endpoint_data_valid().
Doing that makes ipa_endpoint_validate_build() contain a single
line BUILD_BUG_ON() call, so just remove that function and move
the remaining line into ipa_endpoint_data_valid().
One final note: the aggregation time limit value for IPA v4.5 needs
to be computed differently. That is handled in an upcoming patch.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
net/smc: Add support for generic netlink API
Up to version 4 this patch series was using the sock_diag netlink
infrastructure. This version is using the generic netlink API. Generic
netlink API offers a better type safety between kernel and userspace
communication.
Using the generic netlink API the smc module can now provide information
about SMC linkgroups, links and devices (both for SMC-R and SMC-D).
v2: Add missing include to uapi header smc_diag.h.
v3: Apply code style recommendations from review comments.
Instead of using EXPORTs to allow the smc_diag module to access
data of the smc module, introduce struct smc_diag_ops and let
smc_diag access the required data using function pointers.
v4: Address checkpatch.pl warnings. Do not use static inline for
functions.
v5: Use generic netlink API instead of the sock_diag netlink
infrastructure.
v6: Integrate more review comments from Jakub.
v7: Use nla_nest_start() with the new family. Use .maxattr=1 in the
genl family and define one entry for attribute 1 in the policy to
reject this attritbute for all commands. All other possible attributes
are rejected because NL_VALIDATE_STRICT is set for the policy
implicitely, which includes NL_VALIDATE_MAXTYPE.
Setting policy[0].strict_start_type=1 does not work here because there
is no valid attribute defined for this family, only plain commands. For
any type > maxtype (which is .maxattr) validate_nla() would return 0 to
userspace instead of -EINVAL. What helps here is __nla_validate_parse()
which checks for type > maxtype and returns -EINVAL when NL_VALIDATE_MAXTYPE
is set. This requires the one entry for type == .maxattr with
.type = NLA_REJECT in the nla_policy.
When a future command wants to allow attributes then it can easily specify a
dedicated .policy for this new command in the genl_ops array. This dedicated
policy overlays the global policy specified in the genl_family structure.
====================
Guvenc Gulce [Tue, 1 Dec 2020 19:20:46 +0000 (20:20 +0100)]
net/smc: Introduce SMCR get link command
Introduce get link command which loops through
all available links of all available link groups. It
uses the SMC-R linkgroup list as entry point, not
the socket list, which makes linkgroup diagnosis
possible, in case linkgroup does not contain active
connections anymore.
Guvenc Gulce [Tue, 1 Dec 2020 19:20:45 +0000 (20:20 +0100)]
net/smc: Introduce SMCR get linkgroup command
Introduce get linkgroup command which loops through
all available SMCR linkgroups. It uses the SMC-R linkgroup
list as entry point, not the socket list, which makes
linkgroup diagnosis possible, in case linkgroup does not
contain active connections anymore.
Guvenc Gulce [Tue, 1 Dec 2020 19:20:41 +0000 (20:20 +0100)]
net/smc: Add diagnostic information to link structure
During link creation add net-device ifindex and ib-device
name to link structure. This is needed for diagnostic purposes.
When diagnostic information is gathered, we need to traverse
device, linkgroup and link structures, to be able to do that
we need to hold a spinlock for the linkgroup list, without this
diagnostic information in link structure, another device list
mutex holding would be necessary to dereference the device
pointer in the link structure which would be impossible when
holding a spinlock already.
Guvenc Gulce [Tue, 1 Dec 2020 19:20:40 +0000 (20:20 +0100)]
net/smc: Add diagnostic information to smc ib-device
During smc ib-device creation, add network device ifindex to smc
ib-device structure. Register for netdevice changes and update ib-device
accordingly. This is needed for diagnostic purposes.
Guvenc Gulce [Tue, 1 Dec 2020 19:20:39 +0000 (20:20 +0100)]
net/smc: Add link counters for IB device ports
Add link counters to the structure of the smc ib device, one counter per
ib port. Increase/decrease the counters as needed in the corresponding
routines.
Karsten Graul [Tue, 1 Dec 2020 19:20:36 +0000 (20:20 +0100)]
net/smc: use helper smc_conn_abort() in listen processing
The helper smc_connect_abort() can be used by the listen processing
functions, too. And rename this helper to smc_conn_abort() to make the
purpose clearer.
No functional change.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rohit Maheshwari [Tue, 1 Dec 2020 09:07:52 +0000 (14:37 +0530)]
net/tls: make sure tls offload sets salt_size
Recent changes made to remove AES constants started using protocol
aware salt_size. ctx->prot_info's salt_size is filled in tls sw case,
but not in tls offload mode, and was working so far because of the
hard coded value was used.
Eric Dumazet [Tue, 1 Dec 2020 09:05:07 +0000 (01:05 -0800)]
geneve: pull IP header before ECN decapsulation
IP_ECN_decapsulate() and IP6_ECN_decapsulate() assume
IP header is already pulled.
geneve does not ensure this yet.
Fixing this generically in IP_ECN_decapsulate() and
IP6_ECN_decapsulate() is not possible, since callers
pass a pointer that might be freed by pskb_may_pull()
Toke Høiland-Jørgensen [Mon, 30 Nov 2020 18:37:05 +0000 (19:37 +0100)]
inet_ecn: Fix endianness of checksum update when setting ECT(1)
When adding support for propagating ECT(1) marking in IP headers it seems I
suffered from endianness-confusion in the checksum update calculation: In
fact the ECN field is in the *lower* bits of the first 16-bit word of the
IP header when calculating in network byte order. This means that the
addition performed to update the checksum field was wrong; let's fix that.
Fixes: b723748750ec ("tunnel: Propagate ECT(1) when decapsulating as recommended by RFC6040") Reported-by: Jonathan Morton <chromatix99@gmail.com> Tested-by: Pete Heist <pete@heistp.net> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20201130183705.17540-1-toke@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some rare ctcm updates by Sebastian, who cleans up all places where
in_interrupt() was used to determine the correct GFP_* mask for
allocations.
In the first three patches we can get rid of those allocations entirely,
as they just end up being copied into the skb.
====================
Sebastian Andrzej Siewior [Mon, 30 Nov 2020 10:09:50 +0000 (11:09 +0100)]
s390/ctcm: Use GFP_ATOMIC in ctcmpc_tx().
gfp_type() uses in_interrupt() to figure out the correct GFP mask.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
ctcmpc_tx() is used as net_device_ops::ndo_start_xmit. This callback is
invoked with disabled bottom halves.
Use GFP_ATOMIC for memory allocation in ctcmpc_tx().
Remove gfp_type() since the last user is gone.
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior [Mon, 30 Nov 2020 10:09:49 +0000 (11:09 +0100)]
s390/ctcm: Use GFP_KERNEL in add_channel().
gfp_type() uses in_interrupt() to figure out the correct GFP mask.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
The memory allocation of `ch' a few lines above is using GFP_KERNEL,
also an allocation a few lines later is using GFP_KERNEL.
Use GFP_KERNEL for the memory allocation.
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior [Mon, 30 Nov 2020 10:09:48 +0000 (11:09 +0100)]
s390/ctcm: Use explicit allocation mask in ctcmpc_unpack_skb().
gfp_type() uses in_interrupt() to figure out the correct GFP mask.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
The call chain of ctcmpc_unpack_skb():
ctcmpc_bh()
-> ctcmpc_unpack_skb()
ctcmpc_bh() is a tasklet handler so GFP_ATOMIC is needed.
Use GFP_ATOMIC as allocation type in ctcmpc_unpack_skb().
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior [Mon, 30 Nov 2020 10:09:47 +0000 (11:09 +0100)]
s390/ctcm: Avoid temporary allocation of struct pdu.
The size of struct pdu is 8 byte. The memory is allocated, initialized,
used and deallocated a few lines later.
It is more efficient to avoid the allocation/free dance and assign the
values directly to skb's data part instead of using memcpy() for it.
Avoid an allocation of struct pdu and use the resulting skb pointer
instead.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[jwi: Fix-up the pdu_offset, adjust skb->len for the pushed length.
Reflow the commit msg.] Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / users / jedix / linux-maple.git / log