firmware: qcom: tzmem: blacklist more platforms for SHM Bridge
The SHM bridge makes the Qualcomm RB3 and SM8150-HDK reset while probing
the RMTFS (in qcom_scm_assign_mem()). Blacklist the SHM Bridge on
corresponding platforms using SoC-level compat string. If later it's
found that the bad behaviour is limited just to the particular boards
rather than SoC, the compat strings can be adjusted.
Chris Lew [Thu, 27 Jun 2024 10:48:30 +0000 (16:18 +0530)]
soc: qcom: smp2p: Use devname for interrupt descriptions
When using /proc/interrupts to collect statistics on smp2p interrupt
counts, it is hard to distinguish the different instances of smp2p from
each other. For example to debug a processor boot issue, the ready and
handover interrupts are checked for sanity to ensure the firmware
reached a specific initialization stage.
Remove "smp2p" string from the irq request so that the irq will default
to the device name. Add an .irq_print_chip() callback to print the irq
chip name as the device name. These two changes allow for a unique name
to be used in /proc/interrupts as shown below.
Luca Weiss [Fri, 28 Jun 2024 17:30:23 +0000 (19:30 +0200)]
soc: qcom: smsm: Add missing mailbox dependency to Kconfig
Since the smsm driver got the ability to interact with the mailbox using
the mailbox subsystem and not just syscon, we need to add the dependency
to kconfig as well to avoid compile errors.
Fixes: 75287992f58a ("soc: qcom: smsm: Support using mailbox interface") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202406180006.Z397C67h-lkp@intel.com/ Signed-off-by: Luca Weiss <luca@lucaweiss.eu> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20240628-smsm-kconfig-v1-1-117d5af4ba1f@lucaweiss.eu Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Sibi Sankar [Mon, 24 Jun 2024 09:22:13 +0000 (14:52 +0530)]
soc: qcom: icc-bwmon: Allow for interrupts to be shared across instances
The multiple BWMONv4 instances available on the X1E80100 SoC use the
same interrupt number. Mark them are shared to allow for re-use across
instances.
Using IRQF_SHARED coupled with devm_request_threaded_irq implies that
the irq can still trigger during/after bwmon_remove due to other active
bwmon instances. Handle this race by relying on bwmon_disable to disable
the interrupt and coupled with explicit request/free irqs.
Sibi Sankar [Mon, 24 Jun 2024 09:22:11 +0000 (14:52 +0530)]
dt-bindings: interconnect: qcom,msm8998-bwmon: Remove opp-table from the required list
Remove opp-table from the required list as the bindings shouldn't care
where the OPP tables (referenced by the operating-points-v2 property)
comes from.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Georgi Djakov <djakov@kernel.org> Link: https://lore.kernel.org/r/20240624092214.146935-2-quic_sibis@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Dmitry Baryshkov [Fri, 21 Jun 2024 22:03:43 +0000 (01:03 +0300)]
soc: qcom: add pd-mapper implementation
Existing userspace protection domain mapper implementation has several
issue. It doesn't play well with CONFIG_EXTRA_FIRMWARE, it doesn't
reread JSON files if firmware location is changed (or if firmware was
not available at the time pd-mapper was started but the corresponding
directory is mounted later), etc.
Provide in-kernel service implementing protection domain mapping
required to work with several services, which are provided by the DSP
firmware.
This module is loaded automatically by the remoteproc drivers when
necessary via the symbol dependency. It uses a root node to match a
protection domains map for a particular board. It is not possible to
implement it as a 'driver' as there is no corresponding device.
Tested-by: Steev Klimaszewski <steev@kali.org> Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org> Reviewed-by: Chris Lew <quic_clew@quicinc.com> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20240622-qcom-pd-mapper-v9-4-a84ee3591c8e@linaro.org
[bjorn: include linux/slab.h] Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Dmitry Baryshkov [Fri, 21 Jun 2024 22:03:42 +0000 (01:03 +0300)]
soc: qcom: pdr: extract PDR message marshalling data
The in-kernel PD mapper is going to use same message structures as the
QCOM_PDR_HELPERS module. Extract message marshalling data to separate
module that can be used by both PDR helpers and by PD mapper.
Dmitry Baryshkov [Fri, 21 Jun 2024 22:03:41 +0000 (01:03 +0300)]
soc: qcom: pdr: fix parsing of domains lists
While parsing the domains list, start offsets from 0 rather than from
domains_read. The domains_read is equal to the total count of the
domains we have seen, while the domains list in the message starts from
offset 0.
Dmitry Baryshkov [Fri, 21 Jun 2024 22:03:40 +0000 (01:03 +0300)]
soc: qcom: pdr: protect locator_addr with the main mutex
If the service locator server is restarted fast enough, the PDR can
rewrite locator_addr fields concurrently. Protect them by placing
modification of those fields under the main pdr->lock.
Bartosz Golaszewski [Mon, 27 May 2024 12:55:03 +0000 (14:55 +0200)]
firmware: qcom: scm: clarify the comment in qcom_scm_pas_init_image()
The "memory protection" mechanism mentioned in the comment is the SHM
Bridge. This is also the reason why we do not convert this call to using
the TZ memory allocator.
Bartosz Golaszewski [Mon, 27 May 2024 12:55:02 +0000 (14:55 +0200)]
firmware: qcom: scm: add support for SHM bridge memory carveout
Parse the "memory-region" property and - if present - use it to assign
the dedicated reserved memory to the underlying DMA callbacks which will
then allocate memory for the SCM calls from it.
Bartosz Golaszewski [Mon, 27 May 2024 12:55:01 +0000 (14:55 +0200)]
firmware: qcom: tzmem: enable SHM Bridge support
SHM Bridge is a safety mechanism allowing to limit the amount of memory
shared between the kernel and the TrustZone to regions explicitly marked
as such.
Add a variant of the tzmem allocator that configures the memory pools as
SHM bridges. It also enables the SHM bridge globally so non-SHM bridge
memory will no longer work with SCM calls.
If enabled at build-time, it will still be checked for availability at
run-time. If the architecture doesn't support SHM Bridge, the allocator
will fall back to the generic mode.
Bartosz Golaszewski [Mon, 27 May 2024 12:55:00 +0000 (14:55 +0200)]
firmware: qcom: scm: add support for SHM bridge operations
SHM Bridge is a safety mechanism allowing to limit the amount of memory
shared between the kernel and the TrustZone to regions explicitly marked
as such.
Add low-level primitives for enabling SHM bridge support as well as
creating and destroying SHM bridges to qcom-scm.
Bartosz Golaszewski [Mon, 27 May 2024 12:54:59 +0000 (14:54 +0200)]
firmware: qcom: qseecom: convert to using the TZ allocator
Drop the DMA mapping operations from qcom_scm_qseecom_app_send() and
convert all users of it in the qseecom module to using the TZ allocator
for creating SCM call buffers. As this is largely a module separate from
the SCM driver, let's use a separate memory pool. Set the initial size to
4K and - if we run out - add twice the current amount to the pool.
Bartosz Golaszewski [Mon, 27 May 2024 12:54:54 +0000 (14:54 +0200)]
firmware: qcom: scm: smc: switch to using the SCM allocator
We need to allocate, map and pass a buffer to the trustzone if we have
more than 4 arguments for a given SCM call. Let's use the new TrustZone
allocator for that memory and shrink the code in process.
As this code lives in a different compilation unit than the rest of the
SCM code, we need to provide a helper in the form of
qcom_scm_get_tzmem_pool() that allows the SMC low-level routines to
access the SCM memory pool.
Bartosz Golaszewski [Mon, 27 May 2024 12:54:53 +0000 (14:54 +0200)]
firmware: qcom: scm: enable the TZ mem allocator
Select the TrustZone memory allocator in Kconfig and create a pool of
memory shareable with the TrustZone when probing the SCM driver.
This will allow a gradual conversion of all relevant SCM calls to using
the dedicated allocator.
The policy used for the pool is "on-demand" and the initial size is 0
as - depending on the config - it's possible that no SCM calls needing
to allocate memory will be called. The sizes of possible allocations also
vary substiantially further warranting the "on-demand" approach.
Bartosz Golaszewski [Mon, 27 May 2024 12:54:52 +0000 (14:54 +0200)]
firmware: qcom: add a dedicated TrustZone buffer allocator
We have several SCM calls that require passing buffers to the TrustZone
on top of the SMC core which allocates memory for calls that require
more than 4 arguments.
Currently every user does their own thing which leads to code
duplication. Many users call dma_alloc_coherent() for every call which
is terribly unperformant (speed- and size-wise).
Provide a set of library functions for creating and managing pools of
memory which is suitable for sharing with the TrustZone, that is:
page-aligned, contiguous and non-cachable as well as provides a way of
mapping of kernel virtual addresses to physical space.
Make the allocator ready for extending with additional modes of operation
which will allow us to support the SHM bridge safety mechanism once all
users convert.
Konrad Dybcio [Wed, 5 Jun 2024 20:10:15 +0000 (22:10 +0200)]
soc: qcom: smem: Add a feature code getter
Recent (SM8550+ ish) Qualcomm SoCs have a new mechanism for precisely
identifying the specific SKU and the precise speed bin (in the general
meaning of this word, anyway): a pair of values called Product Code
and Feature Code.
Based on this information, we can deduce the available frequencies for
things such as Adreno. In the case of Adreno specifically, Pcode is
useless for non-prototype SoCs.
Introduce a getter for the feature code and export it.
Konrad Dybcio [Wed, 5 Jun 2024 20:10:14 +0000 (22:10 +0200)]
soc: qcom: Move some socinfo defines to the header
In preparation for parsing the chip "feature code" (FC) and "product
code" (PC) (essentially the parameters that let us conclusively
characterize the sillicon we're running on, including various speed
bins), move the socinfo version defines to the public header.
Luca Weiss [Thu, 6 Jun 2024 19:18:33 +0000 (21:18 +0200)]
soc: qcom: smsm: Support using mailbox interface
Add support for using the mbox interface instead of manually writing to
the syscon. With this change the driver will attempt to get the mailbox
first, and if that fails it will fall back to the existing way of using
qcom,ipc-* properties and converting to syscon.
Luca Weiss [Thu, 6 Jun 2024 19:18:32 +0000 (21:18 +0200)]
dt-bindings: soc: qcom,smsm: Allow specifying mboxes instead of qcom,ipc
The qcom,ipc-N properties are essentially providing a reference to a
mailbox, so allow using the mboxes property to do the same in a more
structured way.
Since multiple SMSM hosts are supported, we need to be able to provide
the correct mailbox for each host. The old qcom,ipc-N properties map to
the mboxes property by index, starting at 0 since that's a valid SMSM
host also.
Mark the older qcom,ipc-N as deprecated and update the example with
mboxes.
Unnathi Chalicheemala [Fri, 31 May 2024 16:45:25 +0000 (09:45 -0700)]
soc: qcom: llcc: Add regmap for Broadcast_AND region
Until SM8450, there was only one broadcast region (Broadcast_OR)
used to broadcast write and check for status bit 0.
>From SM8450 onwards another broadcast region (Broadcast_AND) has been
added which checks for status bit 1. This hasn't been updated and
Broadcast_OR region was wrongly being used to check for status bit 1 all
along.
Hence define new regmap structure for Broadcast_AND region and initialize
this regmap when HW block version is greater than 4.1, otherwise
initialize as a NULL pointer for backwards compatibility.
Switch from broadcast_OR to broadcast_AND region (when defined in DT)
for checking status bit 1 as Broadcast_OR region checks only for bit 0.
The LLCC block in SM8450, SM8550 and SM8650 have a new register
space for Broadcast_AND region. This is used to check that all
channels have bit set to "1", mainly in SCID activation/deactivation.
Previously we were mapping only the Broadcast_OR region assuming
there was only one broadcast register region. Now we also map
Broadcast_AND region.
Kathiravan Thirumoorthy [Mon, 25 Mar 2024 15:49:50 +0000 (21:19 +0530)]
cpufreq: qcom-nvmem: add support for IPQ5321
Like all other SoCs in IPQ5332 family, cpufreq for IPQ5321 is also
determined by the eFuse, with the maximum limit of 1.1GHz. Add support
for the same.
Stephen Boyd [Thu, 9 May 2024 18:41:28 +0000 (11:41 -0700)]
soc: qcom: rpmh-rsc: Ensure irqs aren't disabled by rpmh_rsc_send_data() callers
Dan pointed out that Smatch is concerned about this code because it uses
spin_lock_irqsave() and then calls wait_event_lock_irq() which enables
irqs before going to sleep. The comment above the function says it
should be called with interrupts enabled, but we simply hope that's true
without really confirming that. Let's add a might_sleep() here to
confirm that interrupts and preemption aren't disabled. Once we do that,
we can change the lock to be non-saving, spin_lock_irq(), to clarify
that we don't expect irqs to be disabled. If irqs are disabled by
callers they're going to be enabled anyway in the wait_event_lock_irq()
call which would be bad.
This should make Smatch happier and find bad callers faster with the
might_sleep(). We can drop the WARN_ON() in the caller because we have
the might_sleep() now, simplifying the code.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/r/911181ed-c430-4592-ad26-4dc948834e08@moroto.mountain Fixes: 2bc20f3c8487 ("soc: qcom: rpmh-rsc: Sleep waiting for tcs slots to be free") Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20240509184129.3924422-1-swboyd@chromium.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Chen Ni [Fri, 10 May 2024 08:31:56 +0000 (16:31 +0800)]
soc: qcom: pmic_glink: Handle the return value of pmic_glink_init
As platform_driver_register() and register_rpmsg_driver() can return
error numbers, it should be better to check the return value and deal
with the exception.
Kent Overstreet [Fri, 24 May 2024 15:42:09 +0000 (11:42 -0400)]
mm: percpu: Include smp.h in alloc_tag.h
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Linus Torvalds [Sun, 26 May 2024 16:54:26 +0000 (09:54 -0700)]
Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com> Cc: Ethan Adams <j.ethan.adams@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Tycho Andersen <tycho@tycho.pizza> Cc: Yang Jihong <yangjihong@bytedance.com> Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Sun, 26 May 2024 05:33:10 +0000 (22:33 -0700)]
Merge tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
Linus Torvalds [Sat, 25 May 2024 22:10:33 +0000 (15:10 -0700)]
Merge tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
Linus Torvalds [Sat, 25 May 2024 21:48:40 +0000 (14:48 -0700)]
Merge tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
- Fix x86 IRQ vector leak caused by a CPU offlining race
- Fix build failure in the riscv-imsic irqchip driver
caused by an API-change semantic conflict
- Fix use-after-free in irq_find_at_or_after()
* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
Linus Torvalds [Sat, 25 May 2024 21:40:09 +0000 (14:40 -0700)]
Merge tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix regressions of the new x86 CPU VFM (vendor/family/model)
enumeration/matching code
- Fix crash kernel detection on buggy firmware with
non-compliant ACPI MADT tables
- Address Kconfig warning
* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
crypto: x86/aes-xts - switch to new Intel CPU model defines
x86/topology: Handle bogus ACPI tables correctly
x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y
Linus Torvalds [Sat, 25 May 2024 21:23:58 +0000 (14:23 -0700)]
Merge tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A series from Xiubo that adds support for additional access checks
based on MDS auth caps which were recently made available to clients.
This is needed to prevent scenarios where the MDS quietly discards
updates that a UID-restricted client previously (wrongfully) acked to
the user.
Other than that, just a documentation fixup"
* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
doc: ceph: update userspace command to get CephFS metadata
ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
ceph: check the cephx mds auth access for async dirop
ceph: check the cephx mds auth access for open
ceph: check the cephx mds auth access for setattr
ceph: add ceph_mds_check_access() helper
ceph: save cap_auths in MDS client when session is opened
Linus Torvalds [Sat, 25 May 2024 21:19:01 +0000 (14:19 -0700)]
Merge tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
"Fixes:
- reusing of the file index (could cause the file to be trimmed)
- infinite dir enumeration
- taking DOS names into account during link counting
- le32_to_cpu conversion, 32 bit overflow, NULL check
- some code was refactored
Changes:
- removed max link count info display during driver init
Remove:
- atomic_open has been removed for lack of use"
* tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: Break dir enumeration if directory contents error
fs/ntfs3: Fix case when index is reused during tree transformation
fs/ntfs3: Mark volume as dirty if xattr is broken
fs/ntfs3: Always make file nonresident on fallocate call
fs/ntfs3: Redesign ntfs_create_inode to return error code instead of inode
fs/ntfs3: Use variable length array instead of fixed size
fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
fs/ntfs3: Check 'folio' pointer for NULL
fs/ntfs3: Missed le32_to_cpu conversion
fs/ntfs3: Remove max link count info display during driver init
fs/ntfs3: Taking DOS names into account during link counting
fs/ntfs3: remove atomic_open
fs/ntfs3: use kcalloc() instead of kzalloc()
Linus Torvalds [Sat, 25 May 2024 21:15:39 +0000 (14:15 -0700)]
Merge tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Two ksmbd server fixes, both for stable"
* tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: ignore trailing slashes in share paths
ksmbd: avoid to send duplicate oplock break notifications
Linus Torvalds [Sat, 25 May 2024 20:33:53 +0000 (13:33 -0700)]
Merge tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is one new driver and then most of the changes are the device
tree bindings conversions to yaml.
New driver:
- Epson RX8111
Drivers:
- Many Device Tree bindings conversions to dtschema
- pcf8563: wakeup-source support"
* tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
pcf8563: add wakeup-source support
rtc: rx8111: handle VLOW flag
rtc: rx8111: demote warnings to debug level
rtc: rx6110: Constify struct regmap_config
dt-bindings: rtc: convert trivial devices into dtschema
dt-bindings: rtc: stmp3xxx-rtc: convert to dtschema
dt-bindings: rtc: pxa-rtc: convert to dtschema
rtc: Add driver for Epson RX8111
dt-bindings: rtc: Add Epson RX8111
rtc: mcp795: drop unneeded MODULE_ALIAS
rtc: nuvoton: Modify part number value
rtc: test: Split rtc unit test into slow and normal speed test
dt-bindings: rtc: nxp,lpc1788-rtc: convert to dtschema
dt-bindings: rtc: digicolor-rtc: move to trivial-rtc
dt-bindings: rtc: alphascale,asm9260-rtc: convert to dtschema
dt-bindings: rtc: armada-380-rtc: convert to dtschema
rtc: cros-ec: provide ID table for avoiding fallback match
Linus Torvalds [Sat, 25 May 2024 20:28:29 +0000 (13:28 -0700)]
Merge tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Runtime PM (power management) is improved and hot-join support has
been added to the dw controller driver.
Core:
- Allow device driver to trigger controller runtime PM
Drivers:
- dw: hot-join support
- svc: better IBI handling"
* tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: dw: Add hot-join support.
i3c: master: Enable runtime PM for master controller
i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
i3c: master: svc: change ENXIO to EAGAIN when IBI occurs during start frame
i3c: Add comment for -EAGAIN in i3c_device_do_priv_xfers()
Linus Torvalds [Sat, 25 May 2024 20:23:42 +0000 (13:23 -0700)]
Merge tag 'jffs2-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull jffs2 updates from Richard Weinberger:
- Fix illegal memory access in jffs2_free_inode()
- Kernel-doc fixes
- print symbolic error names
* tag 'jffs2-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: Fix potential illegal address access in jffs2_free_inode
jffs2: Simplify the allocation of slab caches
jffs2: nodemgmt: fix kernel-doc comments
jffs2: print symbolic error name instead of error code
Linus Torvalds [Sat, 25 May 2024 20:17:48 +0000 (13:17 -0700)]
Merge tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull UML updates from Richard Weinberger:
- Fixes for -Wmissing-prototypes warnings and further cleanup
- Remove callback returning void from rtc and virtio drivers
- Fix bash location
* tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: (26 commits)
um: virtio_uml: Convert to platform remove callback returning void
um: rtc: Convert to platform remove callback returning void
um: Remove unused do_get_thread_area function
um: Fix -Wmissing-prototypes warnings for __vdso_*
um: Add an internal header shared among the user code
um: Fix the declaration of kasan_map_memory
um: Fix the -Wmissing-prototypes warning for get_thread_reg
um: Fix the -Wmissing-prototypes warning for __switch_mm
um: Fix -Wmissing-prototypes warnings for (rt_)sigreturn
um: Stop tracking host PID in cpu_tasks
um: process: remove unused 'n' variable
um: vector: remove unused len variable/calculation
um: vector: fix bpfflash parameter evaluation
um: slirp: remove set but unused variable 'pid'
um: signal: move pid variable where needed
um: Makefile: use bash from the environment
um: Add winch to winch_handlers before registering winch IRQ
um: Fix -Wmissing-prototypes warnings for __warp_* and foo
um: Fix -Wmissing-prototypes warnings for text_poke*
um: Move declarations to proper headers
...
Linus Torvalds [Sat, 25 May 2024 00:28:02 +0000 (17:28 -0700)]
Merge tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Some fixes for the end of the merge window, mostly amdgpu and panthor,
with one nouveau uAPI change that fixes a bad decision we made a few
months back.
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe
work"
* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
drm/amdgpu/atomfirmware: add intergrated info v2.3 table
drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
drm/bridge: adv7511: Attach next bridge without creating connector
drm/buddy: Fix the warn on's during force merge
drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
drm/panthor: Call panthor_sched_post_reset() even if the reset failed
drm/panthor: Reset the FW VM to NULL on unplug
drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
drm/panthor: Force an immediate reset on unrecoverable faults
drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
drm/panthor: Fix an off-by-one in the heap context retrieval logic
drm/panthor: Relax the constraints on the tiler chunk size
drm/panthor: Make sure the tiler initial/max chunks are consistent
drm/panthor: Fix tiler OOM handling to allow incremental rendering
drm: xlnx: zynqmp_dpsub: Fix compilation error
drm: xlnx: zynqmp_dpsub: Fix few function comments
David Howells [Fri, 24 May 2024 14:23:36 +0000 (15:23 +0100)]
cifs: Fix missing set of remote_i_size
Occasionally, the generic/001 xfstest will fail indicating corruption in
one of the copy chains when run on cifs against a server that supports
FSCTL_DUPLICATE_EXTENTS_TO_FILE (eg. Samba with a share on btrfs). The
problem is that the remote_i_size value isn't updated by cifs_setsize()
when called by smb2_duplicate_extents(), but i_size *is*.
This may cause cifs_remap_file_range() to then skip the bit after calling
->duplicate_extents() that sets sizes.
Fix this by calling netfs_resize_file() in smb2_duplicate_extents() before
calling cifs_setsize() to set i_size.
This means we don't then need to call netfs_resize_file() upon return from
->duplicate_extents(), but we also fix the test to compare against the pre-dup
inode size.
[Note that this goes back before the addition of remote_i_size with the
netfs_inode struct. It should probably have been setting cifsi->server_eof
previously.]
Fixes: cfc63fc8126a ("smb3: fix cached file size problems in duplicate extents (reflink)") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev Signed-off-by: Steve French <stfrench@microsoft.com>
David Howells [Wed, 22 May 2024 08:38:48 +0000 (09:38 +0100)]
cifs: Fix smb3_insert_range() to move the zero_point
Fix smb3_insert_range() to move the zero_point over to the new EOF.
Without this, generic/147 fails as reads of data beyond the old EOF point
return zeroes.
Fixes: 3ee1a1fc3981 ("cifs: Cut over to using netfslib") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev Signed-off-by: Steve French <stfrench@microsoft.com>
Chengming Zhou [Mon, 13 May 2024 03:07:56 +0000 (11:07 +0800)]
mm/ksm: fix possible UAF of stable_node
The commit 2c653d0ee2ae ("ksm: introduce ksm_max_page_sharing per page
deduplication limit") introduced a possible failure case in the
stable_tree_insert(), where we may free the new allocated stable_node_dup
if we fail to prepare the missing chain node.
Then that kfolio return and unlock with a freed stable_node set... And
any MM activities can come in to access kfolio->mapping, so UAF.
Fix it by moving folio_set_stable_node() to the end after stable_node
is inserted successfully.
Link: https://lkml.kernel.org/r/20240513-b4-ksm-stable-node-uaf-v1-1-f687de76f452@linux.dev Fixes: 2c653d0ee2ae ("ksm: introduce ksm_max_page_sharing per page deduplication limit") Signed-off-by: Chengming Zhou <chengming.zhou@linux.dev> Acked-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Stefan Roesch <shr@devkernel.io> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
memory_failure
try_memory_failure_hugetlb
me_huge_page
__page_handle_poison
dissolve_free_hugetlb_folio
drain_all_pages -- Buddy page can be isolated e.g. for compaction.
take_page_off_buddy -- Failed as page is not in the buddy list.
-- Page can be putback into buddy after compaction.
page_ref_inc -- Leads to buddy page with refcnt = 1.
Then unpoison_memory() can unpoison the page and send the buddy page back
into buddy list again leading to the above bad page state warning. And
bad_page() will call page_mapcount_reset() to remove PageBuddy from buddy
page leading to later VM_BUG_ON_PAGE(!PageBuddy(page)) when trying to
allocate this page.
Fix this issue by only treating __page_handle_poison() as successful when
it returns 1.
Link: https://lkml.kernel.org/r/20240523071217.1696196-1-linmiaohe@huawei.com Fixes: ceaf8fbea79a ("mm, hwpoison: skip raw hwpoison page in freeing 1GB hugepage") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Naoya Horiguchi <nao.horiguchi@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Yuanyuan Zhong [Thu, 23 May 2024 18:35:31 +0000 (12:35 -0600)]
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
After switching smaps_rollup to use VMA iterator, searching for next entry
is part of the condition expression of the do-while loop. So the current
VMA needs to be addressed before the continue statement.
Otherwise, with some VMAs skipped, userspace observed memory
consumption from /proc/pid/smaps_rollup will be smaller than the sum of
the corresponding fields from /proc/pid/smaps.
Link: https://lkml.kernel.org/r/20240523183531.2535436-1-yzhong@purestorage.com Fixes: c4c84f06285e ("fs/proc/task_mmu: stop using linked list and highest_vm_end") Signed-off-by: Yuanyuan Zhong <yzhong@purestorage.com> Reviewed-by: Mohamed Khalfella <mkhalfella@purestorage.com> Cc: David Hildenbrand <david@redhat.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Ryusuke Konishi [Mon, 20 May 2024 13:26:21 +0000 (22:26 +0900)]
nilfs2: fix potential hang in nilfs_detach_log_writer()
Syzbot has reported a potential hang in nilfs_detach_log_writer() called
during nilfs2 unmount.
Analysis revealed that this is because nilfs_segctor_sync(), which
synchronizes with the log writer thread, can be called after
nilfs_segctor_destroy() terminates that thread, as shown in the call trace
below:
Fix this issue by changing nilfs_segctor_sync() so that the log writer
thread returns normally without synchronizing after it terminates, and by
forcing tasks that are already waiting to complete once after the thread
terminates.
The skipped inode metadata flushout will then be processed together in the
subsequent cleanup work in nilfs_segctor_destroy().
Ryusuke Konishi [Mon, 20 May 2024 13:26:20 +0000 (22:26 +0900)]
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
A potential and reproducible race issue has been identified where
nilfs_segctor_sync() would block even after the log writer thread writes a
checkpoint, unless there is an interrupt or other trigger to resume log
writing.
This turned out to be because, depending on the execution timing of the
log writer thread running in parallel, the log writer thread may skip
responding to nilfs_segctor_sync(), which causes a call to schedule()
waiting for completion within nilfs_segctor_sync() to lose the opportunity
to wake up.
The reason why waking up the task waiting in nilfs_segctor_sync() may be
skipped is that updating the request generation issued using a shared
sequence counter and adding an wait queue entry to the request wait queue
to the log writer, are not done atomically. There is a possibility that
log writing and request completion notification by nilfs_segctor_wakeup()
may occur between the two operations, and in that case, the wait queue
entry is not yet visible to nilfs_segctor_wakeup() and the wake-up of
nilfs_segctor_sync() will be carried over until the next request occurs.
Fix this issue by performing these two operations simultaneously within
the lock section of sc_state_lock. Also, following the memory barrier
guidelines for event waiting loops, move the call to set_current_state()
in the same location into the event waiting loop to ensure that a memory
barrier is inserted just before the event condition determination.
Ryusuke Konishi [Mon, 20 May 2024 13:26:19 +0000 (22:26 +0900)]
nilfs2: fix use-after-free of timer for log writer thread
Patch series "nilfs2: fix log writer related issues".
This bug fix series covers three nilfs2 log writer-related issues,
including a timer use-after-free issue and potential deadlock issue on
unmount, and a potential freeze issue in event synchronization found
during their analysis. Details are described in each commit log.
This patch (of 3):
A use-after-free issue has been reported regarding the timer sc_timer on
the nilfs_sc_info structure.
The problem is that even though it is used to wake up a sleeping log
writer thread, sc_timer is not shut down until the nilfs_sc_info structure
is about to be freed, and is used regardless of the thread's lifetime.
Fix this issue by limiting the use of sc_timer only while the log writer
thread is alive.
Link: https://lkml.kernel.org/r/20240520132621.4054-1-konishi.ryusuke@gmail.com Link: https://lkml.kernel.org/r/20240520132621.4054-2-konishi.ryusuke@gmail.com Fixes: fdce895ea5dd ("nilfs2: change sc_timer from a pointer to an embedded one in struct nilfs_sc_info") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: "Bai, Shuangpeng" <sjb7183@psu.edu> Closes: https://groups.google.com/g/syzkaller/c/MK_LYqtt8ko/m/8rgdWeseAwAJ Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Michael Ellerman [Tue, 21 May 2024 03:02:19 +0000 (13:02 +1000)]
selftests/mm: fix build warnings on ppc64
Fix warnings like:
In file included from uffd-unit-tests.c:8:
uffd-unit-tests.c: In function `uffd_poison_handle_fault':
uffd-common.h:45:33: warning: format `%llu' expects argument of type
`long long unsigned int', but argument 3 has type `__u64' {aka `long
unsigned int'} [-Wformat=]
By switching to unsigned long long for u64 for ppc64 builds.
The problem is because bpf_arch_text_copy() silently fails to write to the
read-only area as a result of patch_map() faulting and the resulting
-EFAULT being chucked away.
Update patch_map() to use CONFIG_EXECMEM instead of
CONFIG_STRICT_MODULE_RWX to check for vmalloc addresses.
Link: https://lkml.kernel.org/r/20240521213813.703309-1-rppt@kernel.org Fixes: 2c9e5d4a0082 ("bpf: remove CONFIG_BPF_JIT dependency on CONFIG_MODULES of") Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org> Reported-by: Klara Modin <klarasmodin@gmail.com> Closes: https://lore.kernel.org/all/7983fbbf-0127-457c-9394-8d6e4299c685@gmail.com Tested-by: Klara Modin <klarasmodin@gmail.com> Cc: Björn Töpel <bjorn@kernel.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Dev Jain [Tue, 21 May 2024 07:43:58 +0000 (13:13 +0530)]
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
Reset nr_hugepages to zero before the start of the test.
If a non-zero number of hugepages is already set before the start of the
test, the following problems arise:
- The probability of the test getting OOM-killed increases. Proof:
The test wants to run on 80% of available memory to prevent OOM-killing
(see original code comments). Let the value of mem_free at the start
of the test, when nr_hugepages = 0, be x. In the other case, when
nr_hugepages > 0, let the memory consumed by hugepages be y. In the
former case, the test operates on 0.8 * x of memory. In the latter,
the test operates on 0.8 * (x - y) of memory, with y already filled,
hence, memory consumed is y + 0.8 * (x - y) = 0.8 * x + 0.2 * y > 0.8 *
x. Q.E.D
- The probability of a bogus test success increases. Proof: Let the
memory consumed by hugepages be greater than 25% of x, with x and y
defined as above. The definition of compaction_index is c_index = (x -
y)/z where z is the memory consumed by hugepages after trying to
increase them again. In check_compaction(), we set the number of
hugepages to zero, and then increase them back; the probability that
they will be set back to consume at least y amount of memory again is
very high (since there is not much delay between the two attempts of
changing nr_hugepages). Hence, z >= y > (x/4) (by the 25% assumption).
Therefore, c_index = (x - y)/z <= (x - y)/y = x/y - 1 < 4 - 1 = 3
hence, c_index can always be forced to be less than 3, thereby the test
succeeding always. Q.E.D
Link: https://lkml.kernel.org/r/20240521074358.675031-4-dev.jain@arm.com Fixes: bd67d5c15cc1 ("Test compaction of mlocked memory") Signed-off-by: Dev Jain <dev.jain@arm.com> Cc: <stable@vger.kernel.org> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Sri Jayaramappa <sjayaram@akamai.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Dev Jain [Tue, 21 May 2024 07:43:57 +0000 (13:13 +0530)]
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
Currently, the test tries to set nr_hugepages to zero, but that is not
actually done because the file offset is not reset after read(). Fix that
using lseek().
Link: https://lkml.kernel.org/r/20240521074358.675031-3-dev.jain@arm.com Fixes: bd67d5c15cc1 ("Test compaction of mlocked memory") Signed-off-by: Dev Jain <dev.jain@arm.com> Cc: <stable@vger.kernel.org> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Sri Jayaramappa <sjayaram@akamai.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Dev Jain [Tue, 21 May 2024 07:43:56 +0000 (13:13 +0530)]
selftests/mm: compaction_test: fix bogus test success on Aarch64
Patch series "Fixes for compaction_test", v2.
The compaction_test memory selftest introduces fragmentation in memory
and then tries to allocate as many hugepages as possible. This series
addresses some problems.
On Aarch64, if nr_hugepages == 0, then the test trivially succeeds since
compaction_index becomes 0, which is less than 3, due to no division by
zero exception being raised. We fix that by checking for division by
zero.
Secondly, correctly set the number of hugepages to zero before trying
to set a large number of them.
Now, consider a situation in which, at the start of the test, a non-zero
number of hugepages have been already set (while running the entire
selftests/mm suite, or manually by the admin). The test operates on 80%
of memory to avoid OOM-killer invocation, and because some memory is
already blocked by hugepages, it would increase the chance of OOM-killing.
Also, since mem_free used in check_compaction() is the value before we
set nr_hugepages to zero, the chance that the compaction_index will
be small is very high if the preset nr_hugepages was high, leading to a
bogus test success.
This patch (of 3):
Currently, if at runtime we are not able to allocate a huge page, the test
will trivially pass on Aarch64 due to no exception being raised on
division by zero while computing compaction_index. Fix that by checking
for nr_hugepages == 0. Anyways, in general, avoid a division by zero by
exiting the program beforehand. While at it, fix a typo, and handle the
case where the number of hugepages may overflow an integer.
The root cause is that HWPoison flag will be set for huge_zero_folio
without increasing the folio refcnt. But then unpoison_memory() will
decrease the folio refcnt unexpectedly as it appears like a successfully
hwpoisoned folio leading to VM_BUG_ON_PAGE(page_ref_count(page) == 0) when
releasing huge_zero_folio.
Skip unpoisoning huge_zero_folio in unpoison_memory() to fix this issue.
We're not prepared to unpoison huge_zero_folio yet.
Link: https://lkml.kernel.org/r/20240516122608.22610-1-linmiaohe@huawei.com Fixes: 478d134e9506 ("mm/huge_memory: do not overkill when splitting huge_zero_page") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Acked-by: David Hildenbrand <david@redhat.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Naoya Horiguchi <nao.horiguchi@gmail.com> Cc: Xu Yu <xuyu@linux.alibaba.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Andrey Konovalov [Fri, 17 May 2024 13:01:18 +0000 (15:01 +0200)]
kasan, fortify: properly rename memintrinsics
After commit 69d4c0d32186 ("entry, kasan, x86: Disallow overriding mem*()
functions") and the follow-up fixes, with CONFIG_FORTIFY_SOURCE enabled,
even though the compiler instruments meminstrinsics by generating calls to
__asan/__hwasan_ prefixed functions, FORTIFY_SOURCE still uses
uninstrumented memset/memmove/memcpy as the underlying functions.
As a result, KASAN cannot detect bad accesses in memset/memmove/memcpy.
This also makes KASAN tests corrupt kernel memory and cause crashes.
To fix this, use __asan_/__hwasan_memset/memmove/memcpy as the underlying
functions whenever appropriate. Do this only for the instrumented code
(as indicated by __SANITIZE_ADDRESS__).
Link: https://lkml.kernel.org/r/20240517130118.759301-1-andrey.konovalov@linux.dev Fixes: 69d4c0d32186 ("entry, kasan, x86: Disallow overriding mem*() functions") Fixes: 51287dcb00cc ("kasan: emit different calls for instrumentable memintrinsics") Fixes: 36be5cba99f6 ("kasan: treat meminstrinsic as builtins in uninstrumented files") Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com> Reported-by: Erhard Furtner <erhard_f@mailbox.org> Reported-by: Nico Pache <npache@redhat.com> Closes: https://lore.kernel.org/all/20240501144156.17e65021@outsider.home/ Reviewed-by: Marco Elver <elver@google.com> Tested-by: Nico Pache <npache@redhat.com> Acked-by: Nico Pache <npache@redhat.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Daniel Axtens <dja@axtens.net> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Hailong.Liu [Fri, 10 May 2024 10:01:31 +0000 (18:01 +0800)]
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
commit a421ef303008 ("mm: allow !GFP_KERNEL allocations for kvmalloc")
includes support for __GFP_NOFAIL, but it presents a conflict with commit dd544141b9eb ("vmalloc: back off when the current task is OOM-killed"). A
possible scenario is as follows:
process-a
__vmalloc_node_range(GFP_KERNEL | __GFP_NOFAIL)
__vmalloc_area_node()
vm_area_alloc_pages()
--> oom-killer send SIGKILL to process-a
if (fatal_signal_pending(current)) break;
--> return NULL;
To fix this, do not check fatal_signal_pending() in vm_area_alloc_pages()
if __GFP_NOFAIL set.
This issue occurred during OPLUS KASAN TEST. Below is part of the log
-> oom-killer sends signal to process
[65731.222840] [ T1308] oom-kill:constraint=CONSTRAINT_NONE,nodemask=(null),cpuset=/,mems_allowed=0,global_oom,task_memcg=/apps/uid_10198,task=gs.intelligence,pid=32454,uid=10198
Linus Torvalds [Fri, 24 May 2024 17:46:35 +0000 (10:46 -0700)]
Merge tag 'riscv-for-linus-6.10-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- The compression format used for boot images is now configurable at
build time, and these formats are shown in `make help`
- access_ok() has been optimized
- A pair of performance bugs have been fixed in the uaccess handlers
- Various fixes and cleanups, including one for the IMSIC build failure
and one for the early-boot ftrace illegal NOPs bug
* tag 'riscv-for-linus-6.10-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix early ftrace nop patching
irqchip: riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
riscv: selftests: Add signal handling vector tests
riscv: mm: accelerate pagefault when badaccess
riscv: uaccess: Relax the threshold for fast path
riscv: uaccess: Allow the last potential unrolled copy
riscv: typo in comment for get_f64_reg
Use bool value in set_cpu_online()
riscv: selftests: Add hwprobe binaries to .gitignore
riscv: stacktrace: fixed walk_stackframe()
ftrace: riscv: move from REGS to ARGS
riscv: do not select MODULE_SECTIONS by default
riscv: show help string for riscv-specific targets
riscv: make image compression configurable
riscv: cpufeature: Fix extension subset checking
riscv: cpufeature: Fix thead vector hwcap removal
riscv: rewrite __kernel_map_pages() to fix sleeping in invalid context
riscv: force PAGE_SIZE linear mapping if debug_pagealloc is enabled
riscv: Define TASK_SIZE_MAX for __access_ok()
riscv: Remove PGDIR_SIZE_L3 and TASK_SIZE_MIN
Linus Torvalds [Fri, 24 May 2024 17:24:49 +0000 (10:24 -0700)]
Merge tag 'for-linus-6.10a-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- a small cleanup in the drivers/xen/xenbus Makefile
- a fix of the Xen xenstore driver to improve connecting to a late
started Xenstore
- an enhancement for better support of ballooning in PVH guests
- a cleanup using try_cmpxchg() instead of open coding it
* tag 'for-linus-6.10a-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drivers/xen: Improve the late XenStore init protocol
xen/xenbus: Use *-y instead of *-objs in Makefile
xen/x86: add extra pages to unpopulated-alloc if available
locking/x86/xen: Use try_cmpxchg() in xen_alloc_p2m_entry()
Linus Torvalds [Fri, 24 May 2024 16:40:31 +0000 (09:40 -0700)]
Merge tag 'for-6.10-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"A few more updates, mostly stability fixes or user visible changes:
- fix race in zoned mode during device replace that can lead to
use-after-free
- update return codes and lower message levels for quota rescan where
it's causing false alerts
- fix unexpected qgroup id reuse under some conditions
- fix condition when looking up extent refs
- add option norecovery (removed in 6.8), the intended replacements
haven't been used and some aplications still rely on the old one
- build warning fixes"
* tag 'for-6.10-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: re-introduce 'norecovery' mount option
btrfs: fix end of tree detection when searching for data extent ref
btrfs: scrub: initialize ret in scrub_simple_mirror() to fix compilation warning
btrfs: zoned: fix use-after-free due to race with dev replace
btrfs: qgroup: fix qgroup id collision across mounts
btrfs: qgroup: update rescan message levels and error codes
Linus Torvalds [Fri, 24 May 2024 16:31:50 +0000 (09:31 -0700)]
Merge tag 'erofs-for-6.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull more erofs updates from Gao Xiang:
"The main ones are metadata API conversion to byte offsets by Al Viro.
Another patch gets rid of unnecessary memory allocation out of DEFLATE
decompressor. The remaining one is a trivial cleanup.
- Convert metadata APIs to byte offsets
- Avoid allocating DEFLATE streams unnecessarily
- Some erofs_show_options() cleanup"
* tag 'erofs-for-6.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: avoid allocating DEFLATE streams before mounting
z_erofs_pcluster_begin(): don't bother with rounding position down
erofs: don't round offset down for erofs_read_metabuf()
erofs: don't align offset for erofs_read_metabuf() (simple cases)
erofs: mechanically convert erofs_read_metabuf() to offsets
erofs: clean up erofs_show_options()
Linus Torvalds [Fri, 24 May 2024 16:01:21 +0000 (09:01 -0700)]
Merge tag 'input-for-v6.10-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a change to input core to trim amount of keys data in modalias string
in case when a device declares too many keys and they do not fit in
uevent buffer instead of reporting an error which results in uevent
not being generated at all
- support for Machenike G5 Pro Controller added to xpad driver
- support for FocalTech FT5452 and FT8719 added to edt-ft5x06
- support for new SPMI vibrator added to pm8xxx-vibrator driver
- missing locking added to cyapa touchpad driver
- removal of unused fields in various driver structures
- explicit initialization of i2c_device_id::driver_data to 0 dropped
from input drivers
- other assorted fixes and cleanups.
* tag 'input-for-v6.10-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: edt-ft5x06 - add support for FocalTech FT5452 and FT8719
dt-bindings: input: touchscreen: edt-ft5x06: Document FT5452 and FT8719 support
Input: xpad - add support for Machenike G5 Pro Controller
Input: try trimming too long modalias strings
Input: drop explicit initialization of struct i2c_device_id::driver_data to 0
Input: zet6223 - remove an unused field in struct zet6223_ts
Input: chipone_icn8505 - remove an unused field in struct icn8505_data
Input: cros_ec_keyb - remove an unused field in struct cros_ec_keyb
Input: lpc32xx-keys - remove an unused field in struct lpc32xx_kscan_drv
Input: matrix_keypad - remove an unused field in struct matrix_keypad
Input: tca6416-keypad - remove unused struct tca6416_drv_data
Input: tca6416-keypad - remove an unused field in struct tca6416_keypad_chip
Input: da7280 - remove an unused field in struct da7280_haptic
Input: ff-core - prefer struct_size over open coded arithmetic
Input: cyapa - add missing input core locking to suspend/resume functions
input: pm8xxx-vibrator: add new SPMI vibrator support
dt-bindings: input: qcom,pm8xxx-vib: add new SPMI vibrator module
input: pm8xxx-vibrator: refactor to support new SPMI vibrator
Input: pm8xxx-vibrator - correct VIB_MAX_LEVELS calculation
Input: sur40 - convert le16 to cpu before use
...