Some socket options do getsockopt with optval=NULL to estimate the size
of the final buffer (which is returned via optlen). This breaks BPF
getsockopt assumptions about permitted optval buffer size. Let's enforce
these assumptions only when non-NULL optval is provided.
Florian and Eduard reported hard dead lock:
[ 58.433327] _raw_spin_lock_irqsave+0x40/0x50
[ 58.433334] btf_put+0x43/0x90
[ 58.433338] bpf_find_btf_id+0x157/0x240
[ 58.433353] btf_parse_fields+0x921/0x11c0
This happens since btf->refcount can be 1 at the time of btf_put() and
btf_put() will call btf_free_id() which will try to grab btf_idr_lock
and will dead lock.
Avoid the issue by doing btf_put() without locking.
Fixes: 3d78417b60fb ("bpf: Add bpf_btf_find_by_name_kind() helper.") Fixes: 1e89106da253 ("bpf: Add bpf_core_add_cands() and wire it into bpf_core_apply_relo_insn().") Reported-by: Florian Westphal <fw@strlen.de> Reported-by: Eduard Zingerman <eddyz87@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Eduard Zingerman <eddyz87@gmail.com> Link: https://lore.kernel.org/bpf/20230421014901.70908-1-alexei.starovoitov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The system hang because of dsa_tag_8021q_port_setup()->
stmmac_vlan_rx_add_vid().
I found in stmmac_drv_probe() that cailing pm_runtime_put()
disabled the clock.
First, when the kernel is compiled with CONFIG_PM=y,The stmmac's
resume/suspend is active.
Secondly,stmmac as DSA master,the dsa_tag_8021q_port_setup() function
will callback stmmac_vlan_rx_add_vid when DSA dirver starts. However,
The system is hanged for the stmmac_vlan_rx_add_vid() accesses its
registers after stmmac's clock is closed.
I would suggest adding the pm_runtime_resume_and_get() to the
stmmac_vlan_rx_add_vid().This guarantees that resuming clock output
while in use.
Fixes: b3dcb3127786 ("net: stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()") Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Yan Wang <rk.code@outlook.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On failing to create promisc flow steering table, the pointer is
returned with an error. Nullify it so unloading the driver won't try to
destroy a non existing table.
Failing to create promisc table may happen over BF devices when the ARM
side is going through a firmware tear down. The host side start a
reload flow. While the driver unloads, it tries to remove the promisc
table. Remove WARN in this state as it is a valid error flow.
Use the same timeout for sync reset flow and health recovery flow, since
the former involves driver's recovery from firmware reset, which is
similar to health recovery. Otherwise, in some cases, such as a firmware
upgrade on the DPU, the firmware pre-init bit may not be ready within
current timeout and the driver will abort loading back after reset.
Revert this patch as we need the "recovery" arg back in mlx5_load_one()
function. This arg will be used in the next patch for using recovery
timeout during sync reset flow.
The original behavior introduced by commit c6acd629eec7 ("net/mlx5e: Add
support for devlink-port in non-representors mode") correctly
re-instantiated uplink devlink port and related netdevice during devlink
reload. However with migration to auxiliary devices, this behaviour
changed.
Restore the original behaviour and tear down auxiliary devices
completely during devlink reload.
On representor init rx error flow the flow steering pointer is being
released so mlx5e_attach_netdev() doesn't have a valid fs pointer
in its error flow. Make sure the pointer is nullified when released
and add a check in mlx5e_fs_cleanup() to verify fs is not null
as representor cleanup callback would be called anyway.
Fixes: af8bbf730068 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Source port rewrite (forward to ovs internal port or statck device) isn't
supported in the rule of split action. So there is no indirect table in
split rule. The cited commit destroyes indirect table in split rule. The
indirect table for other rules will be destroyed wrongly. It will cause
traffic loss.
Fix it by removing the destroy function in split rule. And also remove
the destroy function in error flow.
Fixes: 10742efc20a4 ("net/mlx5e: VF tunnel TX traffic offloading") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when creating per vport table, create flags are hardcoded.
Devlink encap mode is set based on user input and HW capability.
Create per vport table based on devlink encap mode.
Fixes: c796bb7cd230 ("net/mlx5: E-switch, Generalize per vport table API") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code already clones post action attributes in
mlx5e_clone_flow_attr_for_post_act(). Creating another copy in
mlx5e_tc_post_act_add() is a erroneous leftover from original
implementation. Instead, assign handle->attribute to post_attr provided by
the caller. Note that cloning the attribute second time is not just
wasteful but also causes issues like second copy not being properly updated
in neigh update code which leads to following use-after-free:
Feb 21 09:02:00 c-237-177-40-045 kernel: BUG: KASAN: use-after-free in mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_report+0xbb/0x1a0
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: __kasan_kmalloc+0x7a/0x90
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_free_info+0x2a/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: ____kasan_slab_free+0x11a/0x1b0
Feb 21 09:02:00 c-237-177-40-045 kernel: page dumped because: kasan: bad access detected
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0: mlx5_cmd_out_err:803:(pid 8833): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0xf2ff71), err(-22)
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0 enp8s0f0: Failed to add post action rule
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_core 0000:08:00.0: mlx5e_tc_encap_flows_add:190:(pid 8833): Failed to update flow post acts, -22
Feb 21 09:02:00 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:02:00 c-237-177-40-045 kernel: <TASK>
Feb 21 09:02:00 c-237-177-40-045 kernel: dump_stack_lvl+0x57/0x7d
Feb 21 09:02:00 c-237-177-40-045 kernel: print_report+0x170/0x471
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_report+0xbb/0x1a0
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_cmd_set_fte+0x200d/0x24c0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: ? __module_address.part.0+0x62/0x200
Feb 21 09:02:00 c-237-177-40-045 kernel: ? mlx5_cmd_stub_create_flow_table+0xd0/0xd0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: ? __raw_spin_lock_init+0x3b/0x110
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_cmd_create_fte+0x80/0xb0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: add_rule_fg+0xe80/0x19c0 [mlx5_core]
--
Feb 21 09:02:00 c-237-177-40-045 kernel: Allocated by task 13476:
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: __kasan_kmalloc+0x7a/0x90
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_packet_reformat_alloc+0x7b/0x230 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_tun_create_header_ipv4+0x977/0xf10 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_attach_encap+0x15b4/0x1e10 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: post_process_attr+0x305/0xa30 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_add_fdb_flow+0x4c0/0xcf0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: __mlx5e_add_fdb_flow+0x7cf/0xe90 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_configure_flower+0xcaa/0x4b90 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_setup_tc_cls_flower+0x99/0x1b0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_setup_tc_cb+0x133/0x1e0 [mlx5_core]
--
Feb 21 09:02:00 c-237-177-40-045 kernel: Freed by task 8833:
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_stack+0x1e/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_set_track+0x21/0x30
Feb 21 09:02:00 c-237-177-40-045 kernel: kasan_save_free_info+0x2a/0x40
Feb 21 09:02:00 c-237-177-40-045 kernel: ____kasan_slab_free+0x11a/0x1b0
Feb 21 09:02:00 c-237-177-40-045 kernel: __kmem_cache_free+0x1de/0x400
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5_packet_reformat_dealloc+0xad/0x100 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_tc_encap_flows_del+0x3c0/0x500 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_update_flows+0x40c/0xa80 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: mlx5e_rep_neigh_update+0x473/0x7a0 [mlx5_core]
Feb 21 09:02:00 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:02:00 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:02:00 c-237-177-40-045 kernel: kthread+0x28f/0x330
Fixes: 8300f225268b ("net/mlx5e: Create new flow attr for multi table actions") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ethtool uses `ETHTOOL_GRXRINGS` to compute how many queues are supported
by RSS. The driver should return the smaller of either:
- The maximum number of RSS queues the device supports, OR
- The number of RX queues configured
Prior to this change, running `ethtool -X $iface default` fails if the
number of queues configured is larger than the number supported by RSS,
even though changing the queue count correctly resets the flowhash to
use all supported queues.
Other drivers (for example, i40e) will succeed but the flow hash will
reset to support the maximum number of queues supported by RSS, even if
that amount is smaller than the configured amount.
After this change, the flowhash can be reset to default which will use
all of the available RSS queues (16) or the configured queue count,
whichever is smaller.
Starting with eth1 which has 10 queues and a flowhash distributing to
all 10 queues:
ixgbe currently returns `EINVAL` whenever the flowhash it set by ethtool
because the ethtool code in the kernel passes a non-zero value for hfunc
that ixgbe should allow.
When ethtool is called with `ETHTOOL_SRXFHINDIR`,
`ethtool_set_rxfh_indir` will call ixgbe's set_rxfh function
with `ETH_RSS_HASH_NO_CHANGE`. This value should be accepted.
When ethtool is called with `ETHTOOL_SRSSH`, `ethtool_set_rxfh` will
call ixgbe's set_rxfh function with `rxfh.hfunc`, which appears to be
hardcoded in ixgbe to always be `ETH_RSS_HASH_TOP`. This value should
also be accepted.
Fix a memory leak that occurs when reading the fw_info
file all the way, since we return NULL indicating no
more data, but don't free the status tracking object.
(struct nf_conn)->timeout is an interval before the conntrack
confirmed. After confirmed, it becomes a timestamp.
It is observed that timeout of an unconfirmed conntrack:
- Set by calling ctnetlink_change_timeout(). As a result,
`nfct_time_stamp` was wrongly added to `ct->timeout` twice.
- Get by calling ctnetlink_dump_timeout(). As a result,
`nfct_time_stamp` was wrongly subtracted.
Separate the 2 cases in:
- Setting `ct->timeout` in __nf_ct_set_timeout().
- Getting `ct->timeout` in ctnetlink_dump_timeout().
Pablo appends:
Update ctnetlink to set up the timeout _after_ the IPS_CONFIRMED flag is
set on, otherwise conntrack creation via ctnetlink breaks.
Note that the problem described in this patch occurs since the
introduction of the nfnetlink_queue conntrack support, select a
sufficiently old Fixes: tag for -stable kernel to pick up this fix.
Fixes: a4b4766c3ceb ("netfilter: nfnetlink_queue: rename related to nfqueue attaching conntrack info") Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
e6d57e9ff0ae ("netfilter: conntrack: fix rmmod double-free race")
consolidates IPS_CONFIRMED bit set in nf_conntrack_hash_check_insert().
However, this breaks ctnetlink:
If the chip reset worker is triggered during the remove process, the chip
DMA may not be properly pushed back to the idle state. This can lead to
corruption of the DMA flow due to the chip reset. Therefore, it is
necessary to stop the chip reset before the DMA is finalized.
To avoid resetting the chip after the reset worker is cancelled, use
__mt7921_mcu_drv_pmctrl() instead of mt7921_mcu_drv_pmctrl(). It is safe to
ignore the pm mutex because the pm worker and wake worker have already been
cancelled.
Fixes: 033ae79b3830 ("mt76: mt7921: refactor init.c to be bus independent") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Co-developed-by: Wang Zhao <wang.zhao@mediatek.com> Signed-off-by: Wang Zhao <wang.zhao@mediatek.com> Signed-off-by: Quan Zhou <quan.zhou@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hardware team has advised the driver that it is necessary to first put
WFDMA into an idle state before resetting the WFDMA. Otherwise, the WFDMA
may enter an unknown state where it cannot be polled with the right state
successfully. To ensure that the DMA can work properly while a stressful
cold reboot test was being made, we have reordered the programming sequence
in the driver based on the hardware team's guidance.
The patch would modify the WFDMA disabling flow from
"DMA reset -> disabling DMASHDL -> disabling WFDMA -> polling and waiting
until DMA idle" to "disabling WFDMA -> polling and waiting for DMA idle ->
disabling DMASHDL -> DMA reset.
Where he polling and waiting until WFDMA is idle is coordinated with the
operation of disabling WFDMA. Even while WFDMA is being disabled, it can
still handle Tx/Rx requests. The additional polling allows sufficient time
for WFDMA to process the last T/Rx request. When the idle state of WFDMA is
reached, it is a reliable indication that DMASHDL is also idle to ensure it
is safe to disable it and perform the DMA reset.
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c") Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Co-developed-by: Wang Zhao <wang.zhao@mediatek.com> Signed-off-by: Wang Zhao <wang.zhao@mediatek.com> Signed-off-by: Quan Zhou <quan.zhou@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
`mt7921u_dma_init` can only return zero or negative number according to its
definition. When it returns non-zero number, there exists an error and this
function should handle this error rather than return directly.
Fixes: 0d2afe09fad5 ("mt76: mt7921: add mt7921u driver") Signed-off-by: Jiefeng Li <jiefeng_li@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MT7921 driver no longer uses eeprom.data, but the relevant code has not
been removed completely since
commit 16d98b548365 ("mt76: mt7921: rely on mcu_get_nic_capability").
This could result in potential invalid memory access.
To fix the kernel panic issue in mt7921, it is necessary to avoid accessing
unallocated eeprom.data which can lead to invalid memory access.
Furthermore, it is possible to entirely eliminate the
mt7921_mcu_parse_eeprom function and solely depend on
mt7921_mcu_parse_response to divide the RxD header.
Fixes: 16d98b548365 ("mt76: mt7921: rely on mcu_get_nic_capability") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
mt76 scan command only support 64 channels currently. If the
channel count is larger than 64(for 2+5+6GHz), some channels will
not be scanned. Hence change the scan type to full channel scan
in case of the command cannot include proper list for chip.
Fixes: 399090ef9605 ("mt76: mt76_connac: move hw_scan and sched_scan routine in mt76_connac_mcu module") Reported-by: Ben Greear <greearb@candelatech.com> Tested-by: Isaac Konikoff <konikofi@candelatech.com> Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
In system warm reboot scene, due to the polling timeout(now 1000us)
is too short to wait dma idle in time, it may make driver probe fail
with error code -ETIMEDOUT. Meanwhile, we also found the dma may take
around 70ms to enter idle state. Change the polling idle timeout to
100ms to avoid the probabilistic probe fail.
Tested pass with 5000 times warm reboot on x86 platform.
[4.477496] pci 0000:01:00.0: attach allowed to drvr mt7921e [internal device]
[4.478306] mt7921e 0000:01:00.0: ASIC revision: 79610010
[4.480063] mt7921e: probe of 0000:01:00.0 failed with error -110
Fixes: 0a1059d0f060 ("mt76: mt7921: move mt7921_dma_reset in dma.c") Signed-off-by: Quan Zhou <quan.zhou@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
The default waiting unit is 10ms and the value is too much for
data path related control. Provide a new API mt76_poll_msec_tick()
to support different cases, such as 1ms polling waiting kick.
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stable-dep-of: c397fc1e6365 ("wifi: mt76: mt7921e: fix probe timeout after reboot") Signed-off-by: Sasha Levin <sashal@kernel.org>
On MT7986 the WiFi driver currently does not get automatically loaded,
requiring manual modprobing because the device tree compatibles are not
exported into metadata.
Add the missing MODULE_DEVICE_TABLE macro to fix this.
Fixes: 99ad32a4ca3a2 ("mt76: mt7915: add support for MT7986") Signed-off-by: Lorenz Brun <lorenz@brun.one> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since we didn't reset t to 0, only the first iteration of the loop
did checked the ready bit several times.
From the second iteration and on, we just tested the bit once and
continued to the next iteration.
When invalidating buffers under the partial tail page,
jbd2_journal_invalidate_folio() returns -EBUSY if the buffer is part of
the committing transaction as we cannot safely modify buffer state.
However if the buffer is already invalidated (due to previous
invalidation attempts from ext4_wait_for_tail_page_commit()), there's
nothing to do and there's no point in returning -EBUSY. This fixes
occasional warnings from ext4_journalled_invalidate_folio() triggered by
generic/051 fstest when blocksize < pagesize.
Fixes: 53e872681fed ("ext4: fix deadlock in journal_unmap_buffer()") Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230329154950.19720-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang static analysis reports this representative issue
dbg.c:1455:6: warning: Branch condition evaluates to
a garbage value
if (!rxf_data.size)
^~~~~~~~~~~~~~
This check depends on iwl_ini_get_rxf_data() to clear
rxf_data but the function can return early without
doing the clear. So move the memset before the early
return.
Clang static analysis reports this issue
d3.c:567:22: warning: The left operand of '>' is
a garbage value
if (seq.tkip.iv32 > cur_rx_iv32)
~~~~~~~~~~~~~ ^
seq is never initialized. Call ieee80211_get_key_rx_seq() to
initialize seq.
Fixes: 0419e5e672d6 ("iwlwifi: mvm: d3: separate TKIP data from key iteration") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20230414130637.6dd372f84f93.If1f708c90e6424a935b4eba3917dfb7582e0dd0a@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't allow buffer allocation TLV with zero req_size since it
leads later to division by zero in iwl_dbg_tlv_alloc_fragments().
Also, NPK/SRAM locations are allowed to have zero buffer req_size,
don't discard them.
handle_read_error() will resumit r10_bio by raid10_read_request(), which
will call bio_start_io_acct() again, while bio_end_io_acct() will only
be called once.
Fix the problem by don't account io again from handle_read_error().
Fixes: 528bc2cf2fcc ("md/raid10: enable io accounting") Suggested-by: Song Liu <song@kernel.org> Signed-off-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230314012258.2395894-1-yukuai1@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
raid10_sync_request() will add 'r10bio->remaining' for both rdev and
replacement rdev. However, if the read io fails, recovery_request_write()
returns without issuing the write io, in this case, end_sync_request()
is only called once and 'remaining' is leaked, cause an io hang.
Fix the problem by decreasing 'remaining' according to if 'bio' and
'repl_bio' is valid.
commit fe630de009d0 ("md/raid10: avoid deadlock on recovery.") allowed
normal io and sync io to exist at the same time. Task hung will occur as
below:
T1 T2 T3 T4
raid10d
handle_read_error
allow_barrier
conf->nr_pending--
-> 0
//submit sync io
raid10_sync_request
raise_barrier
->will not be blocked
...
//submit to drivers
raid10_read_request
wait_barrier
conf->nr_pending++
-> 1
//retry read fail
raid10_end_read_request
reschedule_retry
add to retry_list
conf->nr_queued++
-> 1
//sync io fail
end_sync_read
__end_sync_read
reschedule_retry
add to retry_list
conf->nr_queued++
-> 2
...
handle_read_error
get form retry_list
conf->nr_queued--
freeze_array
wait nr_pending == nr_queued+1
->1 ->2
//task hung
retry read and sync io will be added to retry_list(nr_queued->2) if they
fails. raid10d() called handle_read_error() and hung in freeze_array().
nr_queued will not decrease because raid10d is blocked, nr_pending will
not increase because conf->barrier is not released.
Fix it by moving allow_barrier() after raid10_read_request().
raise_barrier() will wait for nr_waiting to become 0. Therefore, sync io
and regular io will not be issued at the same time.
Also remove the check of nr_queued in stop_waiting_barrier. It can be 0
but don't need to be blocking. Remove the check for MD_RECOVERY_RUNNING as
the check is redundent.
In __replace_atomic_write_block(), we missed to check return value
of inc_valid_block_count(), for extreme testcase that f2fs image is
run out of space, it may cause inconsistent status in between SIT
table and total valid block count.
Cc: Daeho Jeong <daehojeong@google.com> Fixes: 3db1de0e582c ("f2fs: change the current atomic write way") Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the IPC registers are used for sleep control, setting
the IPC sleep bit already triggers an interrupt to the fw, so
there is no need to also set the doorbell. Setting also the
doorbell triggers the sleep interrupt twice which lead to
an assert.
In __iwl_err(), if we rate-limit the message away, then
vaf.va is still NULL-initialized by the time we get to
the tracing code, which then crashes. When it doesn't
get rate-limited out, it's still wrong to reuse the old
args2 that was already printed, which is why we bother
making a copy in the first place.
Currently, perf_event sample period in perf_event_stackmap is set too low
that the test fails randomly. Fix this by using the max sample frequency,
from read_perf_max_sample_freq().
Move read_perf_max_sample_freq() to testing_helpers.c. Replace the CHECK()
with if-printf, as CHECK is not available in testing_helpers.c.
Fixes: 1da4864c2b20 ("selftests/bpf: Add callchain_stackid") Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20230412210423.900851-2-song@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
fcloop_fcp_op() could be called from flush request's ->end_io(flush_end_io) in
which the spinlock of fq->mq_flush_lock is grabbed with irq saved/disabled.
So fcloop_fcp_op() can't call spin_unlock_irq(&tfcp_req->reqlock) simply
which enables irq unconditionally.
Fixes the warning by switching to spin_lock_irqsave()/spin_unlock_irqrestore()
Fixes: c38dbbfab1bc ("nvme-fcloop: fix inconsistent lock state warnings") Reported-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
For an identify command with cns set to NVME_ID_CNS_CS_CTRL, the NVMe
2.0 specification states that:
If the I/O Command Set specified by the CSI field does not have an
Identify Controller data structure, then the controller shall return
a zero filled data structure. If the host requests a data structure for
an I/O Command Set that the controller does not support, the controller
shall abort the command with a status code of Invalid Field in Command.
However, the current implementation of this identify command in
nvmet_execute_identify() only handles the ZNS command set, returning an
error for the NVM command set, which is not compliant with the
specifications as we do support this command set.
Fix this by:
1) Renaming nvmet_execute_identify_cns_cs_ctrl() to
nvmet_execute_identify_ctrl_zns() to continue handling the
ZNS command set as is.
2) Introduce a nvmet_execute_identify_ctrl_ns() helper to handle the
NVM command set, returning a zero filled nvme_id_ctrl_nvm data
structure.
3) Modify nvmet_execute_identify() to call these helpers based on
the csi specified, returning an error for unsupported command sets.
Fixes: aaf2e048af27 ("nvmet: add ZBD over ZNS backend support") Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Tested-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The identify command with cns set to NVME_ID_CNS_NS_ACTIVE_LIST does
not depend on the command set. The execution of this command should
thus not look at the csi field specified in the command. Simplify
nvmet_execute_identify() to directly call
nvmet_execute_identify_nslist() without the csi switch-case.
Fixes: ab5d0b38c047 ("nvmet: add Command Set Identifier support") Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Tested-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The identify command with cns set to NVME_ID_CNS_CTRL does not depend on
the command set. The execution of this command should thus not look at
the csi specified in the command. Simplify nvmet_execute_identify() to
directly call nvmet_execute_identify_ctrl() without the csi switch-case.
Fixes: ab5d0b38c047 ("nvmet: add Command Set Identifier support") Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Tested-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The identify command with cns set to NVME_ID_CNS_NS does not directly
depend on the command set. The NVMe specifications is rather confusing
here as it appears that this command only applies to the NVM command
set. However, footnote 8 of Figure 273 in the NVMe 2.0 base
specifications clearly state that this command applies to NVM command
sets that support logical blocks, that is, NVM and ZNS. Both the NVM and
ZNS command set specifications also list this identify as mandatory.
The command handling should thus not look at the csi field since it is
defined as unused for this command. Given that we do not support the
KV command set, simply remove the csi switch-case for that command
handling and call directly nvmet_execute_identify_ns() in
nvmet_execute_identify().
Fixes: ab5d0b38c047 ("nvmet: add Command Set Identifier support") Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Tested-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the I/O Command Set associated with the namespace identified by the
NSID field does not support the Identify Namespace data structure
specified by the CSI field, the controller shall abort the command with
a status code of Invalid Field in Command.
In other words, if nvmet_execute_identify_cns_cs_ns() is called for a
target with a block device that is not zoned, we should not return any
data and set the status to NVME_SC_INVALID_FIELD.
While at it, it is also better to revalidate the ns block devie *before*
checking if the block device is zoned, to ensure that
nvmet_execute_identify_cns_cs_ns() operates against updated device
characteristics.
Fixes: aaf2e048af27 ("nvmet: add ZBD over ZNS backend support") Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When huang uses sched_switch tracepoint, the tracepoint
does only one thing in the mounted ebpf program, which
deletes the fixed elements in sockhash ([0])
It seems that elements in sockhash are rarely actively
deleted by users or ebpf program. Therefore, we do not
pay much attention to their deletion. Compared with hash
maps, sockhash only provides spin_lock_bh protection.
This causes it to appear to have self-locking behavior
in the interrupt context.
While initializing spectral, the magic value is getting written to the
invalid memory address leading to random boot-up crash. This occurs
due to the incorrect index increment in ath11k_dbring_fill_magic_value
function. Fix it by replacing the existing logic with memset32 to ensure
there is no invalid memory access.
The usual devm_regulator_get() call already handles "optional"
regulators by returning a valid dummy and printing a warning
that the dummy regulator should be described properly. This
code open coded the same behaviour, but masked any errors that
are not -EPROBE_DEFER and is quite noisy.
This change effectively unmasks and propagates regulators errors
not involving -ENODEV, downgrades the error print to warning level
if no regulator is specified and captures the probe defer message
for /sys/kernel/debug/devices_deferred.
Fixes: 2e12f536635f ("net: stmmac: dwmac-rk: Use standard devicetree property for phy regulator") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The clock requesting code is quite repetitive. Fix this by requesting
the clocks via devm_clk_bulk_get_optional. The optional variant has been
used, since this is effectively what the old code did. The exact clocks
required depend on the platform and configuration. As a side effect
this change adds correct -EPROBE_DEFER handling.
Suggested-by: Jakub Kicinski <kuba@kernel.org> Suggested-by: Andrew Lunn <andrew@lunn.ch> Fixes: 7ad269ea1a2b ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When if_type equals zero and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns false, drbl_regs_memmap_p is not remapped. This passes a NULL
pointer to iounmap(), which can trigger a WARN() on certain arches.
When if_type equals six and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns true, drbl_regs_memmap_p may has been remapped and
ctrl_regs_memmap_p is not remapped. This is a resource leak and passes a
NULL pointer to iounmap().
To fix these issues, we need to add null checks before iounmap(), and
change some goto labels.
Fixes: 1351e69fc6db ("scsi: lpfc: Add push-to-adapter support to sli4") Signed-off-by: Shuchang Li <lishuchang@hust.edu.cn> Link: https://lore.kernel.org/r/20230404072133.1022-1-lishuchang@hust.edu.cn Reviewed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When tracing a kernel function with arg type is u32*, btf_ctx_access()
would report error: arg2 type INT is not a struct.
The commit bb6728d75611 ("bpf: Allow access to int pointer arguments
in tracing programs") added support for int pointer, but did not skip
modifiers before checking it's type. This patch fixes it.
Fixes: bb6728d75611 ("bpf: Allow access to int pointer arguments in tracing programs") Co-developed-by: Chengming Zhou <zhouchengming@bytedance.com> Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com> Signed-off-by: Feng Zhou <zhoufeng.zf@bytedance.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jiri Olsa <jolsa@kernel.org> Link: https://lore.kernel.org/bpf/20230410085908.98493-2-zhoufeng.zf@bytedance.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is: after cp_error is set, f2fs_submit_merged_ipu_write()
in f2fs_write_single_data_page() tries to flush IPU bio in cache, however
f2fs_submit_merged_ipu_write() missed to check validity of @bio parameter,
result in submitting random cached bio which belong to other IO context,
then it will cause use-after-free issue, fix it by adding additional
validity check.
Fixes: 0b20fcec8651 ("f2fs: cache global IPU bio") Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure unaligned descriptors that straddle the end of the UMEM are
considered invalid. Currently, descriptor validation is broken for
zero-copy mode which only checks descriptors at page granularity.
For example, descriptors in zero-copy mode that overrun the end of the
UMEM but not a page boundary are (incorrectly) considered valid. The
UMEM boundary check needs to happen before the page boundary and
contiguity checks in xp_desc_crosses_non_contig_pg(). Do this check in
xp_unaligned_validate_desc() instead like xp_check_unaligned() already
does.
Fixes: 2b43470add8c ("xsk: Introduce AF_XDP buffer allocation API") Signed-off-by: Kal Conley <kal.conley@dectris.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/r/20230405235920.7305-2-kal.conley@dectris.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When jent initialisation fails for any reason other than ENOENT,
the entire drbg fails to initialise, even when we're not in FIPS
mode. This is wrong because we can still use the kernel RNG when
we're not in FIPS mode.
Change it so that it only fails when we are in FIPS mode.
Fixes: 57225e679788 ("crypto: drbg - Use callback API for random readiness") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When dumping the control flow graphs for programs using the 16-byte long
load instruction, we need to skip the second part of this instruction
when looking for the next instruction to process. Otherwise, we end up
printing "BUG_ld_00" from the kernel disassembler in the CFG.
In some cases the loopback latency might be large enough, causing
the assertion on invocations to be run before ingress prog getting
executed. The assertion would fail and the test would flake.
This can be reliably reproduced by arbitrarily increasing the
loopback latency (thanks to [1]):
tc qdisc add dev lo root handle 1: htb default 12
tc class add dev lo parent 1:1 classid 1:12 htb rate 20kbps ceil 20kbps
tc qdisc add dev lo parent 1:12 netem delay 100ms
Fix this by waiting on the receive end, instead of instantly
returning to the assert. The call to read() will wait for the
default SO_RCVTIMEO timeout of 3 seconds provided by
start_server().
Fix flaky STATS_RX_DROPPED test. The receiver calls getsockopt after
receiving the last (valid) packet which is not the final packet sent in
the test (valid and invalid packets are sent in alternating fashion with
the final packet being invalid). Since the last packet may or may not
have been dropped already, both outcomes must be allowed.
This issue could also be fixed by making sure the last packet sent is
valid. This alternative is left as an exercise to the reader (or the
benevolent maintainers of this file).
This problem was quite visible on certain setups. On one machine this
failure was observed 50% of the time.
Also, remove a redundant assignment of pkt_stream->nb_pkts. This field
is already initialized by __pkt_stream_alloc.
Fixes: 27e934bec35b ("selftests: xsk: make stat tests not spin on getsockopt") Signed-off-by: Kal Conley <kal.conley@dectris.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/r/20230403120400.31018-1-kal.conley@dectris.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This change fixes flakiness in the BIDIRECTIONAL test:
# [is_pkt_valid] expected length [60], got length [90]
not ok 1 FAIL: SKB BUSY-POLL BIDIRECTIONAL
When IPv6 is enabled, the interface will periodically send MLDv1 and
MLDv2 packets. These packets can cause the BIDIRECTIONAL test to fail
since it uses VETH0 for RX.
For other tests, this was not a problem since they only receive on VETH1
and IPv6 was already disabled on VETH0.
Avoid UMEM_SIZE macro in testapp_invalid_desc which is incorrect when
the frame size is not XSK_UMEM__DEFAULT_FRAME_SIZE. Also remove the
macro since it's no longer being used.
Fixes: 909f0e28207c ("selftests: xsk: Add tests for 2K frame size") Signed-off-by: Kal Conley <kal.conley@dectris.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/r/20230403145047.33065-2-kal.conley@dectris.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The arguments passed to the trace events are of type unsigned int,
however the signature of the events used __le32 parameters.
I may be missing the point here, but sparse flagged this and it
does seem incorrect to me.
net/qrtr/ns.c: note: in included file (through include/trace/trace_events.h, include/trace/define_trace.h, include/trace/events/qrtr.h):
./include/trace/events/qrtr.h:11:1: warning: cast to restricted __le32
./include/trace/events/qrtr.h:11:1: warning: restricted __le32 degrades to integer
./include/trace/events/qrtr.h:11:1: warning: restricted __le32 degrades to integer
... (a lot more similar warnings)
net/qrtr/ns.c:115:47: expected restricted __le32 [usertype] service
net/qrtr/ns.c:115:47: got unsigned int service
net/qrtr/ns.c:115:61: warning: incorrect type in argument 2 (different base types)
... (a lot more similar warnings)
Fix this by freeing the channel surveys on device removal.
Tested with a RT3070 based USB wireless adapter.
Fixes: 5447626910f5 ("rt2x00: save survey for every channel visited") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230330215637.4332-1-W_Armin@gmx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
If an NCQ error occurs when the IPTT is valid and slot->abort flag is set
in completion path, sas_task_abort() will be called to abort only one NCQ
command now, and the host would be set to SHOST_RECOVERY state. But this
may not kick-off EH Immediately until other outstanding QCs timeouts. As a
result, the host may remain in the SHOST_RECOVERY state for up to 30
seconds, such as follows:
Similar to how AHCI handles NCQ errors in ahci_error_intr() ->
ata_port_abort() -> ata_do_link_abort(), add an NCQ error handler for LLDDs
to call to initiate a link abort.
This will mark all outstanding QCs as failed and kick-off EH.
Note:
A "force reset" argument is added for drivers which require the ATA error
handling to always reset the device.
A driver may require this feature for when SATA device per-SCSI cmnd
resources are only released during reset for ATA EH. As such, we need an
option to force reset to be done, regardless of what any EH autopsy
decides.
The SATA device FIS fields are set to indicate a device error from
ata_eh_analyze_tf().
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Suggested-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/1665998435-199946-2-git-send-email-john.garry@huawei.com Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Tested-by: Niklas Cassel <niklas.cassel@wdc.com> # pm80xx Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: bb544224da77 ("scsi: hisi_sas: Handle NCQ error when IPTT is valid") Signed-off-by: Sasha Levin <sashal@kernel.org>
If there is a failure during copy_from_user or user-provided data buffer is
invalid, rtl_debugfs_set_write_reg should return negative error code instead
of a positive value count.
Fix this bug by returning correct error code. Moreover, the check of buffer
against null is removed since it will be handled by copy_from_user.
Fixes: 610247f46feb ("rtlwifi: Improve debugging by using debugfs") Signed-off-by: Wei Chen <harperchen1110@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230326054217.93492-1-harperchen1110@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If there is a failure during copy_from_user or user-provided data buffer
is invalid, rtl_debugfs_set_write_rfreg should return negative error code
instead of a positive value count.
Fix this bug by returning correct error code. Moreover, the check of buffer
against null is removed since it will be handled by copy_from_user.
Fixes: 610247f46feb ("rtlwifi: Improve debugging by using debugfs") Signed-off-by: Wei Chen <harperchen1110@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230326053138.91338-1-harperchen1110@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The SA2UL Crypto driver provides support for couple of
DES3 algos "cbc(des3_ede)" and "ecb(des3_ede)", and enabling
the crypto selftest throws the following errors (as seen on
K3 J721E SoCs):
saul-crypto 4e00000.crypto: Error allocating fallback algo cbc(des3_ede)
alg: skcipher: failed to allocate transform for cbc-des3-sa2ul: -2
saul-crypto 4e00000.crypto: Error allocating fallback algo ecb(des3_ede)
alg: skcipher: failed to allocate transform for ecb-des3-sa2ul: -2
Fix this by selecting CRYPTO_DES which was missed while
adding base driver support.
Fixes: bff139b49d9f ("f2fs: handle decompress only post processing in softirq") Fixes: 95fa90c9e5a7 ("f2fs: support recording errors into superblock") Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This problem was introduced by the previous commit 7377e853967b ("f2fs:
compress: fix potential deadlock of compress file"). All pagelocks were
released in f2fs_write_raw_pages(), but whether the page was
in the writeback state was ignored in the subsequent writing process.
Let's fix it by waiting for the page to writeback before writing.
Cc: Christoph Hellwig <hch@lst.de> Fixes: 4c8ff7095bef ("f2fs: support data compression") Fixes: 7377e853967b ("f2fs: compress: fix potential deadlock of compress file") Signed-off-by: Qi Han <hanqi@vivo.com> Signed-off-by: Yangtao Li <frank.li@vivo.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we manage the zone capacity per zone type, it'll break the GC assumption.
And, the current logic complains valid block count mismatch.
Let's apply zone capacity to all zone type, if specified.
Fixes: de881df97768 ("f2fs: support zone capacity less than zone size") Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When f2fs skipped a gc round during victim migration, there was a bug which
would skip all upcoming gc rounds unconditionally because skipped_gc_rwsem
was not initialized. It fixes the bug by correctly initializing the
skipped_gc_rwsem inside the gc loop.
Fixes: 6f8d4455060d ("f2fs: avoid fi->i_gc_rwsem[WRITE] lock in f2fs_gc") Signed-off-by: Yonggil Song <yonggil.song@samsung.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix an uninitialized return code if we never found a qfe slot. It would be
a bug if we ever got into this situation, but it's good to return something
tracable.
Fixes: acb3f35f920b ("sunhme: forward the error code from pci_enable_device()") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a bug added in commit f36199355c64 ("scsi: target: iscsi: Fix cmd abort
fabric stop race").
If CMD_T_TAS is set on the se_cmd we must call iscsit_free_cmd() to do the
last put on the cmd and free it, because the connection is down and we will
not up sending the response and doing the put from the normal I/O
path.
Add a check for CMD_T_TAS in iscsit_release_commands_from_conn() so we now
detect this case and run iscsit_free_cmd().
Fixes: f36199355c64 ("scsi: target: iscsi: Fix cmd abort fabric stop race") Signed-off-by: Mike Christie <michael.christie@oracle.com> Link: https://lore.kernel.org/r/20230319015620.96006-9-michael.christie@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a bug where an initiator thinks a LUN_RESET has cleaned up
running commands when it hasn't. The bug was added in commit 51ec502a3266
("target: Delete tmr from list before processing").
The problem occurs when:
1. We have N I/O cmds running in the target layer spread over 2 sessions.
2. The initiator sends a LUN_RESET for each session.
3. session1's LUN_RESET loops over all the running commands from both
sessions and moves them to its local drain_task_list.
4. session2's LUN_RESET does not see the LUN_RESET from session1 because
the commit above has it remove itself. session2 also does not see any
commands since the other reset moved them off the state lists.
5. sessions2's LUN_RESET will then complete with a successful response.
6. sessions2's inititor believes the running commands on its session are
now cleaned up due to the successful response and cleans up the running
commands from its side. It then restarts them.
7. The commands do eventually complete on the backend and the target
starts to return aborted task statuses for them. The initiator will
either throw a invalid ITT error or might accidentally lookup a new
task if the ITT has been reallocated already.
Fix the bug by reverting the patch, and serialize the execution of
LUN_RESETs and Preempt and Aborts.
Also prevent us from waiting on LUN_RESETs in core_tmr_drain_tmr_list,
because it turns out the original patch fixed a bug that was not
mentioned. For LUN_RESET1 core_tmr_drain_tmr_list can see a second
LUN_RESET and wait on it. Then the second reset will run
core_tmr_drain_tmr_list and see the first reset and wait on it resulting in
a deadlock.
Fixes: 51ec502a3266 ("target: Delete tmr from list before processing") Signed-off-by: Mike Christie <michael.christie@oracle.com> Link: https://lore.kernel.org/r/20230319015620.96006-8-michael.christie@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a bug added in commit f36199355c64 ("scsi: target: iscsi: Fix
cmd abort fabric stop race").
If we have multiple sessions to the same se_device we can hit a race where
a LUN_RESET on one session cleans up the se_cmds from under another
session which is being closed. This results in the closing session freeing
its conn/session structs while they are still in use.
The bug is:
1. Session1 has IO se_cmd1.
2. Session2 can also have se_cmds for I/O and optionally TMRs for ABORTS
but then gets a LUN_RESET.
3. The LUN_RESET on session2 sees the se_cmds on session1 and during the
drain stages marks them all with CMD_T_ABORTED.
4. session1 is now closed so iscsit_release_commands_from_conn() only sees
se_cmds with the CMD_T_ABORTED bit set and returns immediately even
though we have outstanding commands.
5. session1's connection and session are freed.
6. The backend request for se_cmd1 completes and it accesses the freed
connection/session.
This hooks the iscsit layer into the cmd counter code, so we can wait for
all outstanding se_cmds before freeing the connection.
Fixes: f36199355c64 ("scsi: target: iscsi: Fix cmd abort fabric stop race") Signed-off-by: Mike Christie <michael.christie@oracle.com> Link: https://lore.kernel.org/r/20230319015620.96006-6-michael.christie@oracle.com Reviewed-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Allow target_get_sess_cmd() users to pass in the cmd counter they want to
use. Right now we pass in the session's cmd counter but in a subsequent
commit iSCSI will switch from per session to per conn.
iSCSI needs to allocate its cmd counter per connection for MCS support
where we need to stop and wait on commands running on a connection instead
of per session. This moves the cmd counter allocation to
target_setup_session() which is used by drivers that need the stop+wait
behavior per session.
xcopy doesn't need stop+wait at all, so we will be OK moving the cmd
counter allocation outside of transport_init_session().
iSCSI needs to wait on outstanding commands like how SRP and the FC/FCoE
drivers do. It can't use target_stop_session() because for MCS support we
can't stop the entire session during recovery because if other connections
are OK then we want to be able to continue to execute I/O on them.
Move the per session cmd counters to a new struct so iSCSI can allocate
them per connection. The xcopy code can also just not allocate in the
future since it doesn't need to track commands.
Signed-off-by: Mike Christie <michael.christie@oracle.com> Link: https://lore.kernel.org/r/20230319015620.96006-2-michael.christie@oracle.com Reviewed-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 395cee83d02d ("scsi: target: iscsit: Stop/wait on cmds during conn close") Signed-off-by: Sasha Levin <sashal@kernel.org>
To determine how many blocks sends in one command, the minimum value is
selected from the hw_max_sectors of both devices. In target_xcopy_do_work,
hw_max_sectors are used as blocks, not sectors; it also ignores the fact
that sectors can be of different sizes, for example 512 and 4096
bytes. Because of this, a number of blocks can be transmitted that the
device will not be able to accept.
Change the selection of max transmission size into bytes.
Reviewed-by: Konstantin Shelekhin <k.shelekhin@yadro.com> Reviewed-by: Dmitriy Bogdanov <d.bogdanov@yadro.com> Signed-off-by: Anastasia Kovaleva <a.kovaleva@yadro.com> Link: https://lore.kernel.org/r/20221114102500.88892-4-a.kovaleva@yadro.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 395cee83d02d ("scsi: target: iscsit: Stop/wait on cmds during conn close") Signed-off-by: Sasha Levin <sashal@kernel.org>
The 64bit umin=9223372036854775810 bound continuously bumps by +1 while
umax=9223372036854775823 stays as-is until the verifier complexity limit
is reached and the program gets finally rejected. During this simulation,
the umin also eventually surpasses umax. Looking at the first 'from 12
to 11' output line from the loop, R1 has the following state:
The var_off has technically not an inconsistent state but it's very
imprecise and far off surpassing 64bit umax bounds whereas the expected
output with refined known bits in var_off should have been like:
In the above log, var_off stays as var_off=(0x8000000000000000; 0xffffffff)
and does not converge into a narrower mask where more bits become known,
eventually transforming R1 into a constant upon umin=9223372036854775823,
umax=9223372036854775823 case where the verifier would have terminated and
let the program pass.
The __reg_combine_64_into_32() marks the subregister unknown and propagates
64bit {s,u}min/{s,u}max bounds to their 32bit equivalents iff they are within
the 32bit universe. The question came up whether __reg_combine_64_into_32()
should special case the situation that when 64bit {s,u}min bounds have
the same value as 64bit {s,u}max bounds to then assign the latter as
well to the 32bit reg->{s,u}32_{min,max}_value. As can be seen from the
above example however, that is just /one/ special case and not a /generic/
solution given above example would still not be addressed this way and
remain at an imprecise var_off=(0x8000000000000000; 0xffffffff).
The improvement is needed in __reg_bound_offset() to refine var32_off with
the updated var64_off instead of the prior reg->var_off. The reg_bounds_sync()
code first refines information about the register's min/max bounds via
__update_reg_bounds() from the current var_off, then in __reg_deduce_bounds()
from sign bit and with the potentially learned bits from bounds it'll
update the var_off tnum in __reg_bound_offset(). For example, intersecting
with the old var_off might have improved bounds slightly, e.g. if umax
was 0x7f...f and var_off was (0; 0xf...fc), then new var_off will then
result in (0; 0x7f...fc). The intersected var64_off holds then the
universe which is a superset of var32_off. The point for the latter is
not to broaden, but to further refine known bits based on the intersection
of var_off with 32 bit bounds, so that we later construct the final var_off
from upper and lower 32 bits. The final __update_reg_bounds() can then
potentially still slightly refine bounds if more bits became known from the
new var_off.
After the improvement, we can see R1 converging successively:
Unlike normal libbpf the light skeleton 'loader' program is doing
btf_find_by_name_kind() call at run-time to find ksym in the kernel and
populate its {btf_id, btf_obj_fd} pair in ld_imm64 insn. To avoid doing the
search multiple times for the same ksym it remembers the first patched ld_imm64
insn and copies {btf_id, btf_obj_fd} from it into subsequent ld_imm64 insn.
Fix a bug in copying logic, since it may incorrectly clear BPF_PSEUDO_BTF_ID flag.
Also replace always true if (btf_obj_fd >= 0) check with unconditional JMP_JA
to clarify the code.
projects / users / dwmw2 / linux.git / log