fsl_usb2_device_register() should stop init if dma_set_mask() return
error.
Fixes: cae058610465 ("drivers/usb/host: fsl: Set DMA_MASK of usb platform device") Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Link: https://lore.kernel.org/r/20201010060308.33693-1-ran.wang_1@nxp.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current tcpm_detach() only reset hard_reset_count if port->attached
is true, this may cause this counter clear is missed if the CC
disconnect event is generated after tcpm_port_reset() is done
by other events, e.g. VBUS off comes first before CC disconect for
a power sink, in that case the first tcpm_detach() will only clear
port->attached flag but leave hard_reset_count there because
tcpm_port_is_disconnected() is still false, then later tcpm_detach()
by CC disconnect will directly return due to port->attached is cleared,
finally this will result tcpm will not try hard reset or error recovery
for later attach.
ChiYuan reported this issue on his platform with below tcpm trace:
After power sink session setup after hard reset 2 times, detach
from the power source and then attach:
[ 4848.046358] VBUS off
[ 4848.046384] state change SNK_READY -> SNK_UNATTACHED
[ 4848.050908] Setting voltage/current limit 0 mV 0 mA
[ 4848.050936] polarity 0
[ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0
[ 4848.053222] Start toggling
[ 4848.086500] state change SNK_UNATTACHED -> TOGGLING
[ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms]
[ 4848.163162] Start toggling
[ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms]
[ 4848.256049] Start toggling
[ 4848.871148] VBUS on
[ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms]
[ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED
[ 4849.088291] polarity 1
[ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2
[ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP
[ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY
[ 4849.088915] Setting voltage/current limit 5000 mV 0 mA
[ 4849.088927] vbus=0 charge:=1
[ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES
[ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms
[ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms]
this patch fix this issue by clear hard_reset_count at any cases
of cc disconnect, í.e. don't check port->attached flag.
Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging") Cc: stable@vger.kernel.org Reported-and-tested-by: ChiYuan Huang <cy_huang@richtek.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Li Jun <jun.li@nxp.com> Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is incorrect in case of a delayed work and causes warnings, usually from
the workqueue:
> WARNING: CPU: 0 PID: 0 at kernel/workqueue.c:1474 __queue_work+0x480/0x528.
When this happens, USB eventually stops working completely after a while.
Also the ACM_ERROR_DELAY bit is never set, so the cooldown mechanism
previously introduced cannot be triggered and acm_submit_read_urb() is
never called.
This changes makes the cdc-acm driver use a single delayed work, fixing the
pointer arithmetic in acm_softint() and set the ACM_ERROR_DELAY when the
cooldown mechanism appear to be needed.
No need to trigger runtime pm in driver removal, otherwise if user
disable auto suspend via sys file, runtime suspend may be entered,
which will call dwc3_core_exit() again and there will be clock disable
not balance warning:
When preparing for SG, not all the entries are prepared at once. When
resume, don't use the remaining request length to calculate for MPS
alignment. Use the entire request->length to do that.
Cc: stable@vger.kernel.org Fixes: 5d187c0454ef ("usb: dwc3: gadget: Don't setup more than requested") Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ZLP handling for ep0 requests is only for control IN
requests. For OUT direction, DWC3 needs to check and setup for MPS
alignment.
Usually, control OUT requests can indicate its transfer size via the
wLength field of the control message. So usb_request->zero is usually
not needed for OUT direction. To handle ZLP OUT for control endpoint,
make sure the TRB is MPS size.
If we fail to find suitable zones for a new readahead extent, we end up
leaving a stale pointer in the global readahead extents radix tree
(fs_info->reada_tree), which can trigger the following trace later on:
1) At reada_find_extent() we don't find any existing readahead extent for
the metadata extent starting at logical address X;
2) So we proceed to create a new one. We then call btrfs_map_block() to get
information about which stripes contain extent X;
3) After that we iterate over the stripes and create only one zone for the
readahead extent - only one because reada_find_zone() returned NULL for
all iterations except for one, either because a memory allocation failed
or it couldn't find the block group of the extent (it may have just been
deleted);
4) We then add the new readahead extent to the readahead extents radix
tree at fs_info->reada_tree;
5) Then we iterate over each zone of the new readahead extent, and find
that the device used for that zone no longer exists, because it was
removed or it was the source device of a device replace operation.
Since this left 'have_zone' set to 0, after finishing the loop we jump
to the 'error' label, call kfree() on the new readahead extent and
return without removing it from the radix tree at fs_info->reada_tree;
6) Any future call to reada_find_extent() for the logical address X will
find the stale pointer in the readahead extents radix tree, increment
its reference counter, which can trigger the use-after-free right
away or return it to the caller reada_add_block() that results in the
use-after-free of the example trace above.
So fix this by making sure we delete the readahead extent from the radix
tree if we fail to setup zones for it (when 'have_zone = 0').
Fixes: 319450211842ba ("btrfs: reada: bypass adding extent when all zone failed") CC: stable@vger.kernel.org # 4.9+ Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fstest btrfs/064 a transaction abort in __btrfs_cow_block could lead
to a system lockup. It gets stuck trying to write back inodes, and the
write back thread was trying to lock an extent buffer:
The problem here is that as soon as we allocate the new block it is
locked and marked dirty in the btree inode. This means that we could
attempt to writeback this block and need to lock the extent buffer.
However we're not unlocking it here and thus we deadlock.
Fix this by unlocking the cow block if we have any errors inside of
__btrfs_cow_block, and also free it so we do not leak it.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btrfs_ioctl_send() used open-coded kvzalloc implementation earlier.
The code was accidentally replaced with kzalloc() call [1]. Restore
the original code by using kvzalloc() to allocate sctx->clone_roots.
During an incremental send, when an inode has multiple new references we
might end up emitting rename operations for orphanizations that have a
source path that is no longer valid due to a previous orphanization of
some directory inode. This causes the receiver to fail since it tries
to rename a path that does not exists.
Example reproducer:
$ cat reproducer.sh
#!/bin/bash
mkfs.btrfs -f /dev/sdi >/dev/null
mount /dev/sdi /mnt/sdi
# Now do a series of changes such that:
#
# *) inode 258 has one new hardlink and the previous name changed
#
# *) both names conflict with the old names of two other inodes:
#
# 1) the new name "d1" conflicts with the old name of inode 259,
# under directory inode 256 (root)
#
# 2) the new name "d2" conflicts with the old name of inode 260
# under directory inode 259
#
# *) inodes 259 and 260 now have the old names of inode 258
#
# *) inode 257 is now located under inode 260 - an inode with a number
# smaller than the inode (258) for which we created a second hard
# link and swapped its names with inodes 259 and 260
#
ln /mnt/sdi/f2 /mnt/sdi/d1/f2_link
mv /mnt/sdi/f1 /mnt/sdi/d1/d2/f1
When executed the receive of the incremental stream fails:
$ ./reproducer.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: rename d1/d2 -> o260-6-0 failed: No such file or directory
This happens because:
1) When processing inode 257 we end up computing the name for inode 259
because it is an ancestor in the send snapshot, and at that point it
still has its old name, "d1", from the parent snapshot because inode
259 was not yet processed. We then cache that name, which is valid
until we start processing inode 259 (or set the progress to 260 after
processing its references);
2) Later we start processing inode 258 and collecting all its new
references into the list sctx->new_refs. The first reference in the
list happens to be the reference for name "d1" while the reference for
name "d2" is next (the last element of the list).
We compute the full path "d1/d2" for this second reference and store
it in the reference (its ->full_path member). The path used for the
new parent directory was "d1" and not "f2" because inode 259, the
new parent, was not yet processed;
3) When we start processing the new references at process_recorded_refs()
we start with the first reference in the list, for the new name "d1".
Because there is a conflicting inode that was not yet processed, which
is directory inode 259, we orphanize it, renaming it from "d1" to
"o259-6-0";
4) Then we start processing the new reference for name "d2", and we
realize it conflicts with the reference of inode 260 in the parent
snapshot. So we issue an orphanization operation for inode 260 by
emitting a rename operation with a destination path of "o260-6-0"
and a source path of "d1/d2" - this source path is the value we
stored in the reference earlier at step 2), corresponding to the
->full_path member of the reference, however that path is no longer
valid due to the orphanization of the directory inode 259 in step 3).
This makes the receiver fail since the path does not exists, it should
have been "o259-6-0/d2".
Fix this by recomputing the full path of a reference before emitting an
orphanization if we previously orphanized any directory, since that
directory could be a parent in the new path. This is a rare scenario so
keeping it simple and not checking if that previously orphanized directory
is in fact an ancestor of the inode we are trying to orphanize.
A test case for fstests follows soon.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Logging directories with many entries can take a significant amount of
time, and in some cases monopolize a cpu/core for a long time if the
logging task doesn't happen to block often enough.
Johannes and Lu Fengqi reported test case generic/041 triggering a soft
lockup when the kernel has CONFIG_SOFTLOCKUP_DETECTOR=y. For this test
case we log an inode with 3002 hard links, and because the test removed
one hard link before fsyncing the file, the inode logging causes the
parent directory do be logged as well, which has 6004 directory items to
log (3002 BTRFS_DIR_ITEM_KEY items plus 3002 BTRFS_DIR_INDEX_KEY items),
so it can take a significant amount of time and trigger the soft lockup.
So just make tree-log.c:log_dir_items() reschedule when necessary,
releasing the current search path before doing so and then resume from
where it was before the reschedule.
The stack trace produced when the soft lockup happens is the following:
Systems booting without the initramfs seems to scan an unusual kind
of device path (/dev/root). And at a later time, the device is updated
to the correct path. We generally print the process name and PID of the
process scanning the device but we don't capture the same information if
the device path is rescanned with a different pathname.
The current message is too long, so drop the unnecessary UUID and add
process name and PID.
While at this also update the duplicate device warning to include the
process name and PID so the messages are consistent
On my platform (i.MX53) bus access sometimes fails with
w1_search: max_slave_count 64 reached, will continue next search.
The reason is the use of jiffies to implement a 200us timeout in
mxc_w1_ds2_touch_bit().
On some platforms the jiffies timer resolution is insufficient for this.
Fix by replacing jiffies by ktime_get().
For consistency apply the same change to the other use of jiffies in
mxc_w1_ds2_reset_bus().
acpi-cpufreq has a old quirk that overrides the _PSD table supplied by
BIOS on AMD CPUs. However the _PSD table of new AMD CPUs (Family 19h+)
now accurately reports the P-state dependency of CPU cores. Hence this
quirk needs to be fixed in order to support new CPUs' frequency control.
Fixes: acd316248205 ("acpi-cpufreq: Add quirk to disable _PSD usage on all AMD CPUs") Signed-off-by: Wei Huang <wei.huang2@amd.com>
[ rjw: Subject edit ] Cc: 3.10+ <stable@vger.kernel.org> # 3.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because acpi_debugger.lock has not been initialized as
acpi_debugger_init() is not called when ACPI is disabled. Fail module
loading to avoid this and any subsequent problems that might arise by
trying to debug AML when ACPI is disabled.
The original intent of 84d3f6b76447 was to delay evaluating lid state until
all drivers have been loaded, with input device being opened from userspace
serving as a signal for this condition. Let's ensure that state updates
happen even if userspace closed (or in the future inhibited) input device.
Note that if we go through suspend/resume cycle we assume the system has
been fully initialized even if LID input device has not been opened yet.
This has a side-effect of fixing access to input->users outside of
input->mutex protections by the way of eliminating said accesses and using
driver private flag.
Fixes: 84d3f6b76447 ("ACPI / button: Delay acpi_lid_initialize_state() until first user space open") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are generating incorrect path in case of rename retry because
we are restarting from wrong dentry. We should restart from the
dentry which was received in the call to nfs_path.
If block_write_full_page() is called for a page that is beyond current
inode size, it will truncate page buffers for the page and return 0.
This logic has been added in 2.5.62 in commit 81eb69062588 ("fix ext3
BUG due to race with truncate") in history.git tree to fix a problem
with ext3 in data=ordered mode. This particular problem doesn't exist
anymore because ext3 is long gone and ext4 handles ordered data
differently. Also normally buffers are invalidated by truncate code and
there's no need to specially handle this in ->writepage() code.
This invalidation of page buffers in block_write_full_page() is causing
issues to filesystems (e.g. ext4 or ocfs2) when block device is shrunk
under filesystem's hands and metadata buffers get discarded while being
tracked by the journalling layer. Although it is obviously "not
supported" it can cause kernel crashes like:
which is not great. The crash happens because bh->b_private is suddently
NULL although BH_JBD flag is still set (this is because
block_invalidatepage() cleared BH_Mapped flag and subsequent bh lookup
found buffer without BH_Mapped set, called init_page_buffers() which has
rewritten bh->b_private). So just remove the invalidation in
block_write_full_page().
Note that the buffer cache invalidation when block device changes size
is already careful to avoid similar problems by using
invalidate_mapping_pages() which skips busy buffers so it was only this
odd block_write_full_page() behavior that could tear down bdev buffers
under filesystem's hands.
Reported-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> CC: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uvc_ctrl_add_info() calls uvc_ctrl_get_flags() which will override
the fixed-up flags set by uvc_ctrl_fixup_xu_info().
uvc_ctrl_init_xu_ctrl() already calls uvc_ctrl_get_flags() before
calling uvc_ctrl_add_info(), so the uvc_ctrl_get_flags() call in
uvc_ctrl_add_info() is not necessary for xu ctrls.
This commit moves the uvc_ctrl_get_flags() call for normal controls
from uvc_ctrl_add_info() to uvc_ctrl_init_ctrl(), so that we no longer
call uvc_ctrl_get_flags() twice for xu controls and so that we no longer
override the fixed-up flags set by uvc_ctrl_fixup_xu_info().
This fixes the xu motor controls not working properly on a Logitech
046d:08cc, and presumably also on the other Logitech models which have
a quirk for this in the uvc_ctrl_fixup_xu_info() function.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two drivers do not provide remove method and use devres for
allocation of other resources, yet they use led_classdev_register
instead of the devres variant, devm_led_classdev_register.
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Álvaro Fernández Rojas <noltari@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Jaedon Shin <jaedon.shin@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither IbsBrTarget nor OPDATA4 are populated in IBS Fetch mode.
Don't accumulate them into raw sample user data in that case.
Also, in Fetch mode, add saving the IBS Fetch Control Extended MSR.
Technically, there is an ABI change here with respect to the IBS raw
sample data format, but I don't see any perf driver version information
being included in perf.data file headers, but, existing users can detect
whether the size of the sample record has reduced by 8 bytes to
determine whether the IBS driver has this fix.
Fixes: 904cb3677f3a ("perf/x86/amd/ibs: Update IBS MSRs and feature definitions") Reported-by: Stephane Eranian <stephane.eranian@google.com> Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200908214740.18097-6-kim.phillips@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_ibs_op_count() adds hardware's current count (IbsOpCurCnt) bits
to its count regardless of hardware's valid status.
According to the PPR for AMD Family 17h Model 31h B0 55803 Rev 0.54,
if the counter rolls over, valid status is set, and the lower 7 bits
of IbsOpCurCnt are randomized by hardware.
Don't include those bits in the driver's event count.
Fixes: 8b1e13638d46 ("perf/x86-ibs: Fix usage of IBS op current count") Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400") Signed-off-by: Raul E Rangel <rrangel@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because cache_size_mutex was unlocked too early in resize_stripes,
which races with grow_one_stripe() that grow_one_stripe() allocates a
stripe with wrong pool_size.
Fix this issue by unlocking cache_size_mutex after updating pool_size.
Cc: <stable@vger.kernel.org> # v4.4+ Reported-by: KoWei Sung <winders@amazon.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A crash can happened when a connect is rejected. The host establishes
the connection after received ConnectReply, and then continues to send
the fabrics Connect command. If the controller does not receive the
ReadyToUse capsule, host may receive a ConnectReject reply.
Call nvme_rdma_destroy_queue_ib after the host received the
RDMA_CM_EVENT_REJECTED event. Then when the fabrics Connect command
times out, nvme_rdma_timeout calls nvme_rdma_complete_rq to fail the
request. A crash happenes due to use after free in
nvme_rdma_complete_rq.
nvme_rdma_destroy_queue_ib is redundant when handling the
RDMA_CM_EVENT_REJECTED event as nvme_rdma_destroy_queue_ib is already
called in connection failure handler.
sgl_alloc_order() can fail when 'length' is large on a memory
constrained system. When order > 0 it will potentially be
making several multi-page allocations with the later ones more
likely to fail than the earlier one. So it is important that
sgl_alloc_order() frees up any pages it has obtained before
returning NULL. In the case when order > 0 it calls the wrong
free page function and leaks. In testing the leak was
sufficient to bring down my 8 GiB laptop with OOM.
Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
There has one race case for ceph's rbd-nbd tool. When do mapping
it may fail with EBUSY from ioctl(nbd, NBD_DO_IT), but actually
the nbd device has already unmaped.
It dues to if just after the wake_up(), the recv_work() is scheduled
out and defers calling the nbd_config_put(), though the map process
has exited the "nbd->recv_task" is not cleared.
Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Callers are generally not supposed to check the return values from
debugfs functions. Debugfs functions never return NULL so this error
handling will never trigger. (Historically debugfs functions used to
return a mix of NULL and error pointers but it was eventually deemed too
complicated for something which wasn't intended to be used in normal
situations).
Delete all the error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Link: https://lore.kernel.org/r/20200826113759.GF393664@mwanda Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Let's fix this by configuring sgx to use 153.6 MHz instead of 307.2 MHz.
Looks like also at least duover needs this change to avoid hangs, so
let's apply it for all 4430.
This helps a bit with thermal issues that seem to be related to memory
corruption when using sgx. It seems that other driver related issues
still remain though.
Cc: Arthur Demchenkov <spinal.by@gmail.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some calls that set attributes, like utimensat(), are not supposed to return
-EINTR and thus do not have handlers for this in glibc which causes us
to leak -EINTR to the applications which are also unprepared to handle it.
For example tar will break if utimensat() return -EINTR and abort unpacking
the archive. Other applications may break too.
To handle this we add checks, and retry, for -EINTR in cifs_setattr()
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In gfs2_check_sb(), no validation checks are performed with regards to
the size of the superblock.
syzkaller detected a slab-out-of-bounds bug that was primarily caused
because the block size for a superblock was set to zero.
A valid size for a superblock is a power of 2 between 512 and PAGE_SIZE.
Performing validation checks and ensuring that the size of the superblock
is valid fixes this bug.
When we try to use file already used as a quota file again (for the same
or different quota type), strange things can happen. At the very least
lockdep annotations may be wrong but also inode flags may be wrongly set
/ reset. When the file is used for two quota types at once we can even
corrupt the file and likely crash the kernel. Catch all these cases by
checking whether passed file is already used as quota file and bail
early in that case.
This fixes occasional generic/219 failure due to lockdep complaint.
Reviewed-by: Andreas Dilger <adilger@dilger.ca> Reported-by: Ritesh Harjani <riteshh@linux.ibm.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20201015110330.28716-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rdc321x_wdt_probe(), rdc321x_wdt_device.queue is initialized
after misc_register(), hence if ioctl is called before its
initialization which can call rdc321x_wdt_start() function,
it will see an uninitialized value of rdc321x_wdt_device.queue,
hence initialize it before misc_register().
Also, rdc321x_wdt_device.default_ticks is accessed in reset()
function called from write callback, thus initialize it before
misc_register().
Found by Linux Driver Verification project (linuxtesting.org).
In p9_fd_create_unix, checking is performed to see if the addr (passed
as an argument) is NULL or not.
However, no check is performed to see if addr is a valid address, i.e.,
it doesn't entirely consist of only 0's.
The initialization of sun_server.sun_path to be equal to this faulty
addr value leads to an uninitialized variable, as detected by KMSAN.
Checking for this (faulty addr) and returning a negative error number
appropriately, resolves this issue.
The open_req and open_ack completion variables are the state variables
to represet a remote channel as open. Use complete_all so there are no
races with waiters and using completion_done.
If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down. The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify
the link up log message as "speed unknown" which makes more sense.
The minus 1 is wrong, this branch should report 2048 bits of space.
With "-1" action, this only report 1024 bit of space.
This bug code returns wrong blocks, but it doesn't inflence bitmap logic:
1. Most callers focus this function return value (the counter of offset),
not the parameter blocks.
2. The bug is only triggered when hijacked is true or map is NULL.
the hijacked true condition is very rare.
the "map == null" only true when array is creating or resizing.
3. Even the caller gets wrong blocks, current code makes caller just to
call md_bitmap_get_counter() one more time.
Signed-off-by: Zhao Heming <heming.zhao@suse.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If you replace a seed device in a sprouted fs, it appears to have
successfully replaced the seed device, but if you look closely, it
didn't. Here is an example.
BTRFS info (device sdb): dev_replace from /dev/sda (devid 1) to /dev/sdc started
BTRFS info (device sdb): dev_replace from /dev/sda (devid 1) to /dev/sdc finished
$ btrfs fi show
Label: none uuid: ab2c88b7-be81-4a7e-9849-c3666e7f9f4f
Total devices 2 FS bytes used 256.00KiB
devid 1 size 3.00GiB used 520.00MiB path /dev/sdc
devid 2 size 3.00GiB used 896.00MiB path /dev/sdb
Label: none uuid: 10bd3202-0415-43af-96a8-d5409f310a7e
Total devices 1 FS bytes used 128.00KiB
devid 1 size 3.00GiB used 536.00MiB path /dev/sda
So as per the replace start command and kernel log replace was successful.
Now let's try to clean mount.
$ umount /btrfs
$ btrfs device scan --forget
$ mount -o device=/dev/sdc /dev/sdb /btrfs
mount: /btrfs: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error.
Fix in this patch:
If a seed is not sprouted then there is no replacement of it, because of
its read-only filesystem with a read-only device. Similarly, in the case
of a sprouted filesystem, the seed device is still read only. So, mark
it as you can't replace a seed device, you can only add a new device and
then delete the seed device. If replace is attempted then returns
-EINVAL.
[Why]
Currently mode validation is bypassed if remote sink exists. That
leads to mode set issue when a BW bottle neck exists in the link path,
e.g., a DP-to-HDMI converter that only supports HDMI 1.4.
Any invalid mode passed to Linux user space will cause the modeset
failure due to limitation of Linux user space implementation.
[How]
Mode validation is skipped only if in edid override. For real remote
sink, clock limit check should be done for HDMI remote sink.
Have HDMI related remote sink going through mode validation to
elimiate modes which pixel clock exceeds BW limitation.
The fr_hard_header function is used to prepend the header to skbs before
transmission. It is used in 3 situations:
1) When a control packet is generated internally in this driver;
2) When a user sends an skb on an Ethernet-emulating PVC device;
3) When a user sends an skb on a normal PVC device.
These 3 situations need to be handled differently by fr_hard_header.
Different headers should be prepended to the skb in different situations.
Currently fr_hard_header distinguishes these 3 situations using
skb->protocol. For situation 1 and 2, a special skb->protocol value
will be assigned before calling fr_hard_header, so that it can recognize
these 2 situations. All skb->protocol values other than these special ones
are treated by fr_hard_header as situation 3.
However, it is possible that in situation 3, the user sends an skb with
one of the special skb->protocol values. In this case, fr_hard_header
would incorrectly treat it as situation 1 or 2.
This patch tries to solve this issue by using skb->dev instead of
skb->protocol to distinguish between these 3 situations. For situation
1, skb->dev would be NULL; for situation 2, skb->dev->type would be
ARPHRD_ETHER; and for situation 3, skb->dev->type would be ARPHRD_DLCI.
This way fr_hard_header would be able to distinguish these 3 situations
correctly regardless what skb->protocol value the user tries to use in
situation 3.
Cc: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function should check the validity of the pxm value before using
it to index the pxm_to_node_map[] array.
Whilst hardening this code may be good in general, the main intent
here is to enable following patches that use this function to replace
acpi_map_pxm_to_node() for non SRAT usecases which should return
NO_NUMA_NODE for PXM entries not matching with those in SRAT.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Barry Song <song.bao.hua@hisilicon.com> Reviewed-by: Hanjun Guo <guohanjun@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When callers pass XFS_BMAPI_REMAP into xfs_bunmapi, they want the extent
to be unmapped from the given file fork without the extent being freed.
We do this for non-rt files, but we forgot to do this for realtime
files. So far this isn't a big deal since nobody makes a bunmapi call
to a rt file with the REMAP flag set, but don't leave a logic bomb.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The @node passed to cpumask_of_node() can be NUMA_NO_NODE, in that
case it will trigger the following WARN_ON(node >= nr_node_ids) due to
mismatched data types of @node and @nr_node_ids. Actually we should
return cpu_all_mask just like most other architectures do if passed
NUMA_NO_NODE.
Also add a similar check to the inline cpumask_of_node() in numa.h.
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
uio_register_device() do two things.
1) get an uio id from a global pool, e.g. the id is <A>
2) create file nodes like /sys/class/uio/uio<A>
uio_unregister_device() do two things.
1) free the uio id <A> and return it to the global pool
2) free the file node /sys/class/uio/uio<A>
There is a situation is that one worker is calling uio_unregister_device(),
and another worker is calling uio_register_device().
If the two workers are X and Y, they go as below sequence,
1) X free the uio id <AAA>
2) Y get an uio id <AAA>
3) Y create file node /sys/class/uio/uio<AAA>
4) X free the file note /sys/class/uio/uio<AAA>
Then it will failed at the 3rd step and cause the phenomenon we saw as it
is creating a duplicated file node.
AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for RISC-V at all even though ARCH_DLINFO will contain one NEW_AUX_ENT
for the VDSO address.
Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com> Reviewed-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On my system the kernel processes the "kgdb_earlycon" parameter before
the "kgdbcon" parameter. When we setup "kgdb_earlycon" we'll end up
in kgdb_register_callbacks() and "kgdb_use_con" won't have been set
yet so we'll never get around to starting "kgdbcon". Let's remedy
this by detecting that the IO module was already registered when
setting "kgdb_use_con" and registering the console then.
As part of this, to avoid pre-declaring things, move the handling of
the "kgdbcon" further down in the file.
The .bss section for the h8300 is relatively small. A value of
CONFIG_LOG_BUF_SHIFT that is larger than 19 will create a static
printk ringbuffer that is too large. Limit the range appropriately
for the H8300.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20200812073122.25412-1-john.ogness@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
In the absence of ACPI or DT topology data, we fallback to haphazardly
decoding *something* out of MPIDR. Sadly, the contents of that register are
mostly unusable due to the implementation leniancy and things like Aff0
having to be capped to 15 (despite being encoded on 8 bits).
Consider a simple system with a single package of 32 cores, all under the
same LLC. We ought to be shoving them in the same core_sibling mask, but
MPIDR is going to look like:
The scheduler's MC domain (all CPUs with same LLC) is going to be built via
arch_topology.c::cpu_coregroup_mask()
In there we try to figure out a sensible mask out of the topology
information we have. In short, here we'll pick the smallest of NUMA or
core sibling mask.
MC mask for CPU16 will thus be 16-19... Uh oh. CPUs 16-19 are in two
different unique MC spans, and the scheduler has no idea what to make of
that. That triggers the WARN_ON() added by commit
We could try to come up with some cleverer scheme to figure out which of
the available masks to pick, but really if one of those masks resulted from
MPIDR then it should be discarded because it's bound to be bogus.
I was hoping to give MPIDR a chance for SMT, to figure out which threads are
in the same core using Aff1-3 as core ID, but Sudeep and Robin pointed out
to me that there are systems out there where *all* cores have non-zero
values in their higher affinity fields (e.g. RK3288 has "5" in all of its
cores' MPIDR.Aff1), which would expose a bogus core ID to userspace.
Stop using MPIDR for topology information. When no other source of topology
information is available, mark each CPU as its own core and its NUMA node
as its LLC domain.
Current code enables the HS clock when video mode is started or to
send out a HS command, and disables the HS clock to send out a LP
command. This is not what DSI spec specify.
Enable HS clock either in command and in video mode.
Set automatic HS clock management for panels and devices that
support non-continuous HS clock.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200701194234.18123-1-yannick.fertre@st.com Signed-off-by: Sasha Levin <sashal@kernel.org>
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
1) the numerator and/or denominator might be 0, in that case
fall back to the default frame interval. This is per the spec
and this caused a v4l2-compliance failure.
2) the updated frame interval wasn't returned in the s_frame_interval
subdev op.
tw5864-video.c:773:32: warning: The left expression of the compound
assignment is an uninitialized value.
The computed value will also be garbage
fintv->stepwise.max.numerator *= std_max_fps;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
stepwise.max is set with frameinterval, which comes from
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
The default RGB quantization range for BT.2020 is full range (just as for
all the other RGB pixel encodings), not limited range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT macro and documentation
accordingly.
Also mention that HSV is always full range and cannot be limited range.
When RGB BT2020 was introduced in V4L2 it was not clear whether it should
be limited or full range, but full range is the right (and consistent)
choice.
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
The realtime bitmap and summary files are regular files that are hidden
away from the directory tree. Since they're regular files, inode
inactivation will try to purge what it thinks are speculative
preallocations beyond the incore size of the file. Unfortunately,
xfs_growfs_rt forgets to update the incore size when it resizes the
inodes, with the result that inactivating the rt inodes at unmount time
will cause their contents to be truncated.
Fix this by updating the incore size when we change the ondisk size as
part of updating the superblock. Note that we don't do this when we're
allocating blocks to the rt inodes because we actually want those blocks
to get purged if the growfs fails.
This fixes corruption complaints from the online rtsummary checker when
running xfs/233. Since that test requires rmap, one can also trigger
this by growing an rt volume, cycling the mount, and creating rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6f24ff97e323 ("power: supply: bq27xxx_battery: Add the
BQ27Z561 Battery monitor") and commit d74534c27775 ("power:
bq27xxx_battery: Add support for additional bq27xxx family devices")
added support for new device types by copying most of the code and
adding necessary quirks.
However they did not copy the code in bq27xxx_battery_status()
responsible for returning POWER_SUPPLY_STATUS_NOT_CHARGING.
Unify the bq27xxx_battery_status() so for all types when charger is
supplied, it will return "not charging" status.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is commit fdfeff0f9e3d ("arm64: hw_breakpoint: Handle inexact
watchpoint addresses") but ported to arm32, which has the same
problem.
This problem was found by Android CTS tests, notably the
"watchpoint_imprecise" test [1]. I tested locally against a copycat
(simplified) version of the test though.
@blkno in f2fs_ra_meta_pages could exceed max segment count, causing panic
in following sanity check in current_sit_addr(), add check condition to
avoid this issue.
In f2fs_lookup(), @res_page could be used before being initialized,
because in __f2fs_find_entry(), once F2FS_I(dir)->i_current_depth was
been fuzzed to zero, then @res_page will never be initialized, causing
this kmsan warning, relocating @res_page initialization place to fix
this bug.
The de facto (and apparently uncommented) standard for using an mm had,
thanks to this code in sparc if nothing else, been that you must have a
reference on mm_users *and that reference must have been obtained with
mmget()*, i.e., from a thread with a reference to mm_users that had used
the mm.
The introduction of mmget_not_zero() in commit d2005e3f41d4
("userfaultfd: don't pin the user memory in userfaultfd_file_create()")
allowed mm_count holders to aoperate on user mappings asynchronously
from the actual threads using the mm, but they were not to load those
mappings into their TLB (i.e., walking vmas and page tables is okay,
kthread_use_mm() is not).
io_uring 2b188cc1bb857 ("Add io_uring IO interface") added code which
does a kthread_use_mm() from a mmget_not_zero() refcount.
The problem with this is code which previously assumed mm == current->mm
and mm->mm_users == 1 implies the mm will remain single-threaded at
least until this thread creates another mm_users reference, has now
broken.
arch/sparc/kernel/smp_64.c:
if (atomic_read(&mm->mm_users) == 1) {
cpumask_copy(mm_cpumask(mm), cpumask_of(cpu));
goto local_flush_and_out;
}
vs fs/io_uring.c
if (unlikely(!(ctx->flags & IORING_SETUP_SQPOLL) ||
!mmget_not_zero(ctx->sqo_mm)))
return -EFAULT;
kthread_use_mm(ctx->sqo_mm);
mmget_not_zero() could come in right after the mm_users == 1 test, then
kthread_use_mm() which sets its CPU in the mm_cpumask. That update could
be lost if cpumask_copy() occurs afterward.
I propose we fix this by allowing mmget_not_zero() to be a first-class
reference, and not have this obscure undocumented and unchecked
restriction.
The basic fix for sparc64 is to remove its mm_cpumask clearing code. The
optimisation could be effectively restored by sending IPIs to mm_cpumask
members and having them remove themselves from mm_cpumask. This is more
tricky so I leave it as an exercise for someone with a sparc64 SMP.
powerpc has a (currently similarly broken) example.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-4-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
powerpc uses IPIs in some situations to switch a kernel thread away
from a lazy tlb mm, which is subject to the TLB flushing race
described in the changelog introducing ARCH_WANT_IRQS_OFF_ACTIVATE_MM.
Reading and modifying current->mm and current->active_mm and switching
mm should be done with irqs off, to prevent races seeing an intermediate
state.
This is similar to commit 38cf307c1f20 ("mm: fix kthread_use_mm() vs TLB
invalidate"). At exec-time when the new mm is activated, the old one
should usually be single-threaded and no longer used, unless something
else is holding an mm_users reference (which may be possible).
Absent other mm_users, there is also a race with preemption and lazy tlb
switching. Consider the kernel_execve case where the current thread is
using a lazy tlb active mm:
If we switch back to the kernel thread from a different mm, there is a
double free of the old active_mm, and a missing free of the new one.
Closing this race only requires interrupts to be disabled while ->mm
and ->active_mm are being switched, but the TLB problem requires also
holding interrupts off over activate_mm. Unfortunately not all archs
can do that yet, e.g., arm defers the switch if irqs are disabled and
expects finish_arch_post_lock_switch() to be called to complete the
flush; um takes a blocking lock in activate_mm().
So as a first step, disable interrupts across the mm/active_mm updates
to close the lazy tlb preempt race, and provide an arch option to
extend that to activate_mm which allows architectures doing IPI based
TLB shootdowns to close the second race.
This is a bit ugly, but in the interest of fixing the bug and backporting
before all architectures are converted this is a compromise.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
[mpe: Manual backport to 4.19 due to membarrier_exec_mmap(mm) changes] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-2-npiggin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with W=1 we get the following warning:
arch/powerpc/platforms/powernv/smp.c: In function ‘pnv_smp_cpu_kill_self’:
arch/powerpc/platforms/powernv/smp.c:276:16: error: suggest braces around
empty body in an ‘if’ statement [-Werror=empty-body]
276 | cpu, srr1);
| ^
cc1: all warnings being treated as errors
The full context is this block:
if (srr1 && !generic_check_cpu_restart(cpu))
DBG("CPU%d Unexpected exit while offline srr1=%lx!\n",
cpu, srr1);
When building with DEBUG undefined DBG() expands to nothing and GCC emits
the warning due to the lack of braces around an empty statement.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200804005410.146094-2-oohall@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If should_futex_fail() returns true in futex_wake_pi(), then the 'ret'
variable is set to -EFAULT and then immediately overwritten. So the failure
injection is non-functional.
Fix it by actually leaving the function and returning -EFAULT.
The Fixes tag is kinda blury because the initial commit which introduced
failure injection was already sloppy, but the below mentioned commit broke
it completely.
ata_qc_complete_multiple() has to be called with the tags physically
active, that is the hw tag is at bit 0. ap->qc_active has the same tag
at bit ATA_TAG_INTERNAL instead, so call ata_qc_get_active() to fix that
up. This is done in the vein of 8385d756e114 ("libata: Fix retrieving of
active qcs").
Each EMAD transaction stores the skb used to issue the EMAD request
('trans->tx_skb') so that the request could be retried in case of a
timeout. The skb can be freed when a corresponding response is received
or as part of the retry logic (e.g., failed retransmit, exceeded maximum
number of retries).
The two tasks (i.e., response processing and retransmits) are
synchronized by the atomic 'trans->active' field which ensures that
responses to inactive transactions are ignored.
In case of a failed retransmit the transaction is finished and all of
its resources are freed. However, the current code does not mark it as
inactive. Syzkaller was able to hit a race condition in which a
concurrent response is processed while the transaction's resources are
being freed, resulting in a use-after-free [1].
Fix the issue by making sure to mark the transaction as inactive after a
failed retransmit and free its resources only if a concurrent task did
not already do that.
[1]
BUG: KASAN: use-after-free in consume_skb+0x30/0x370
net/core/skbuff.c:833
Read of size 4 at addr ffff88804f570494 by task syz-executor.0/1004
Memory state around the buggy address: ffff88804f570380: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff88804f570400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88804f570480: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88804f570500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88804f570580: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Fixes: caf7297e7ab5f ("mlxsw: core: Introduce support for asynchronous EMAD register access") Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC 10 optimizes the scheduler code differently than its predecessors.
When CONFIG_DEBUG_SECTION_MISMATCH=y, the Makefile forces GCC not
to inline some functions (-fno-inline-functions-called-once). Before GCC
10, "no-inlined" __schedule() starts with the usual prologue:
push %bp
mov %sp, %bp
So the ORC unwinder simply picks stack pointer from %bp and
unwinds from __schedule() just perfectly:
But now, with GCC 10, there is no %bp prologue in __schedule():
$ cat /proc/1/stack
<nothing>
The ORC entry of the point in __schedule() is:
sp:sp+88 bp:last_sp-48 type:call end:0
In this case, nobody subtracts sizeof "struct inactive_task_frame" in
__unwind_start(). The struct is put on the stack by __switch_to_asm() and
only then __switch_to_asm() stores %sp to task->thread.sp. But we start
unwinding from a point in __schedule() (stored in frame->ret_addr by
'call') and not in __switch_to_asm().
0xffffffff9376cad0 is __schedule+0x1f0 (after the call to
__switch_to_asm). Now follow those 88 bytes from the ORC entry (sp+88).
The entry is correct, __schedule() really pushes 48 bytes (8*7) + 32 bytes
via subq to store some local values (like 4U below). So to unwind, look
at the offset 88-sizeof(long) = 0x50 from here:
Here ^^^^^^^^^^^^^^^^ is the correct ret addr from
__schedule(). It translates to schedule+0x42 (insn after a call to
__schedule()).
BUT, unwind_next_frame() tries to take the address starting from
0xffff94b50001fdc8. That is exactly from thread.sp+88-sizeof(long) =
0xffff94b50001fdc8+88-8 = 0xffff94b50001fe18, which is garbage marked as
NOTE above. So this quits the unwinding as 7793fab6956b2d00 is obviously
not a kernel address.
There was a fix to skip 'struct inactive_task_frame' in
unwind_get_return_address_ptr in the following commit:
187b96db5ca7 ("x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks")
But we need to skip the struct already in the unwinder proper. So
subtract the size (increase the stack pointer) of the structure in
__unwind_start() directly. This allows for removal of the code added by
commit 187b96db5ca7 completely, as the address is now at
'(unsigned long *)state->sp - 1', the same as in the generic case.
[ mingo: Cleaned up the changelog a bit, for better readability. ]
In order to avoid high dom0 load due to rogue guests sending events at
high frequency, block those events in case there was no action needed
in dom0 to handle the events.
This is done by adding a per-event counter, which set to zero in case
an EOI without the XEN_EOI_FLAG_SPURIOUS is received from a backend
driver, and incremented when this flag has been set. In case the
counter is 2 or higher delay the EOI by 1 << (cnt - 2) jiffies, but
not more than 1 second.
In order not to waste memory shorten the per-event refcnt to two bytes
(it should normally never exceed a value of 2). Add an overflow check
to evtchn_get() to make sure the 2 bytes really won't overflow.
In case rogue guests are sending events at high frequency it might
happen that xen_evtchn_do_upcall() won't stop processing events in
dom0. As this is done in irq handling a crash might be the result.
In order to avoid that, delay further inter-domain events after some
time in xen_evtchn_do_upcall() by forcing eoi processing into a
worker on the same cpu, thus inhibiting new events coming in.
The time after which eoi processing is to be delayed is configurable
via a new module parameter "event_loop_timeout" which specifies the
maximum event loop time in jiffies (default: 2, the value was chosen
after some tests showing that a value of 2 was the lowest with an
only slight drop of dom0 network throughput while multiple guests
performed an event storm).
How long eoi processing will be delayed can be specified via another
parameter "event_eoi_delay" (again in jiffies, default 10, again the
value was chosen after testing with different delay values).
Today only fifo event channels have a cpu hotplug callback. In order
to prepare for more percpu (de)init work move that callback into
events_base.c and add percpu_init() and percpu_deinit() hooks to
struct evtchn_ops.
This is part of XSA-332.
Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving pcifront use the lateeoi irq
binding for pciback and unmask the event channel only just before
leaving the event handling function.
Restructure the handling to support that scheme. Basically an event can
come in for two reasons: either a normal request for a pciback action,
which is handled in a worker, or in case the guest has finished an AER
request which was requested by pciback.
When an AER request is issued to the guest and a normal pciback action
is currently active issue an EOI early in order to be able to receive
another event when the AER request has been finished by the guest.
Let the worker processing the normal requests run until no further
request is pending, instead of starting a new worker ion that case.
Issue the EOI only just before leaving the worker.
This scheme allows to drop calling the generic function
xen_pcibk_test_and_schedule_op() after processing of any request as
the handling of both request types is now separated more cleanly.
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving pvcallsfront use the lateeoi
irq binding for pvcallsback and unmask the event channel only after
handling all write requests, which are the ones coming in via an irq.
This requires modifying the logic a little bit to not require an event
for each write request, but to keep the ioworker running until no
further data is found on the ring page to be processed.
projects / users / dwmw2 / linux.git / log