We use tcm_loop with tape emulations running on tcmu.
In case application reads a short tape block with a longer READ, or a long
tape block with a short READ, according to SCC spec data has to be
tranferred _and_ sensebytes with ILI set and information field containing
the residual count. Similar problem also exists when using fixed block
size in READ.
Up to now tcm_loop is not prepared to handle sensebytes if input data is
provided, as in tcm_loop_queue_data_in() it only sets SAM_STAT_GOOD and, if
necessary, the residual count.
To fix the bug, the same handling for sensebytes as present in
tcm_loop_queue_status() must be done in tcm_loop_queue_data_in() also.
After adding this handling, the two function now are nearly identical, so I
created a single function with two wrappers.
While preparing the driver for upstream this detail was missed.
If not asserted during the initialization process, devices connected on
the bus will not be made aware of the internal reset happening. This,
potentially resulting in unexpected behavior.
In the probe function, in case of error, resources allocated in
'lp8788_setup_adc_channel()' must be released.
This can be achieved easily by using the devm_ variant of
'iio_channel_get()'.
This has the extra benefit to simplify the remove function and to axe the
'lp8788_release_adc_channel()' function which is now useless.
Fixes: 98a276649358 ("power_supply: Add new lp8788 charger driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Although the value of FDF is used just for outgoing stream, the assignment
to union member is done for both directions of stream. At present this
causes no issue because the value of same position is reassigned later for
opposite stream. However, it's better to add if statement.
Fixes: d3d10a4a1b19 ("ALSA: firewire-lib: use union for directional parameters") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20200508043635.349339-2-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The issue happens because no real ISP reset is executed. The
qla2x00_abort_isp(scsi_qla_host_t *vha) function expects that
vha->flags.online will be not zero for ISP reset procedure. This patch
sets vha->flags.online to 1 before calling ->abort_isp() for starting the
ISP reset.
7d715a6c1ae5 ("PCI: add PCI Express ASPM support") added the ability for
Linux to enable ASPM, but for some undocumented reason, it didn't enable
ASPM on links where the downstream component is a PCIe-to-PCI/PCI-X Bridge.
Remove this exclusion so we can enable ASPM on these links.
The Dell OptiPlex 7080 mentioned in the bugzilla has a TI XIO2001
PCIe-to-PCI Bridge. Enabling ASPM on the link leading to it allows the
Intel SoC to enter deeper Package C-states, which is a significant power
savings.
The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between
a CPU address (which is determined by the window number 'x') and a
programmed PCI address - Thus allowing the controller to translate CPU
accesses into PCI accesses.
However the existing code incorrectly writes the CPU address - lets fix
this by writing the PCI address instead.
For memory transactions, existing DT users describe a 1:1 identity mapping
and thus this change should have no effect. However the same isn't true for
I/O.
Link: https://lore.kernel.org/r/20191004132941.6660-1-andrew.murray@arm.com Fixes: c25da4778803 ("PCI: rcar: Add Renesas R-Car PCIe driver") Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com> Signed-off-by: Andrew Murray <andrew.murray@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If platform bus driver registration is failed then, accessing
platform bus spin lock (&drv->driver.bus->p->klist_drivers.k_lock)
in __platform_driver_probe() without verifying the return value
__platform_driver_register() can lead to NULL pointer exception.
So check the return value before attempting the spin lock.
One such example is below:
For a custom usecase, I have intentionally failed the platform bus
registration and I expected all the platform device/driver
registrations to fail gracefully. But I came across this panic
issue.
The IRQ log output is supposed to appear on a single line. However,
commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.
Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.
Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_OF is disabled, gcc-9 produces a warning about the
wfx_sdio_of_match[] array having a declaration without a dimension:
drivers/staging/wfx/bus_sdio.c:159:34: error: array 'wfx_sdio_of_match' assumed to have one element [-Werror]
159 | static const struct of_device_id wfx_sdio_of_match[];
| ^~~~~~~~~~~~~~~~~
Move the proper declaration up and out of the #ifdef instead.
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Older compilers like gcc-4.8 don't see that the variable is
initialized when it is used:
In file included from include/linux/compiler_types.h:68:0,
from <command-line>:0:
drivers/hid/intel-ish-hid/ishtp-fw-loader.c: In function 'load_fw_from_host':
include/linux/compiler-gcc.h:75:45: warning: 'fw_info.ldr_capability.max_dma_buf_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
#define __UNIQUE_ID(prefix) __PASTE(__PASTE(__UNIQUE_ID_, prefix), __COUNTER__)
^
drivers/hid/intel-ish-hid/ishtp-fw-loader.c:770:22: note: 'fw_info.ldr_capability.max_dma_buf_size' was declared here
struct shim_fw_info fw_info;
^
Make sure to initialize it before returning an error from ish_query_loader_prop().
Fixes the following warnings for both g5 and g6 SoCs:
arch/arm/boot/dts/aspeed-g5.dtsi:376.19-381.8: Warning
(unit_address_vs_reg): /ahb/apb/lpc@1e789000/lpc-bmc@0/kcs1@0: node
has a unit name, but no reg property
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to ASPEED, FTTMR010 is not intended to be used in the AST2600.
The arch timer should be used, but Linux doesn't enable high-res timers
without being assured that the arch timer is always on, so set that
property in the devicetree.
The FTTMR010 device is described by set to disabled.
This fixes highres timer support for AST2600.
Fixes: 2ca5646b5c2f ("ARM: dts: aspeed: Add AST2600 and EVB") Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error handling flow seems incorrect, there is no reason to try and
add debugfs support if the device registration did not
succeed. Return on error.
When calling regmap_update_bits(), since map->reg_update_bits is NULL,
_regmap_read() is entered with the following logic:
if (!map->cache_bypass) {
ret = regcache_read(map, reg, val);
if (ret == 0)
return 0;
}
if (map->cache_only)
return -EBUSY;
regcache_read() hits -EINVAL because MAX98373_R2000_SW_RESET is volatile,
as map->cache_only is set by codec suspend, thus -EBUSY is returned.
Fix by moving max98373_reset() after cache_only set to false in max98373_resume().
Not all u-boot versions initialize the HHI_GP_PLL_CNTL[2-5] registers.
In that case all HHI_GPLL_PLL_CNTL[1-5] registers are 0x0 and when
booting Linux the PLL fails to lock.
The initialization sequence from u-boot is:
- put the PLL into reset
- write 0x59C88000 to HHI_GP_PLL_CNTL2
- write 0xCA463823 to HHI_GP_PLL_CNTL3
- write 0x0286A027 to HHI_GP_PLL_CNTL4
- write 0x00003000 to HHI_GP_PLL_CNTL5
- set M, N, OD and the enable bit
- take the PLL out of reset
- check if it has locked
- disable the PLL
In Linux we already initialize M, N, OD, the enable and the reset bits.
Also the HHI_GP_PLL_CNTL[2-5] registers with these magic values (the
exact meaning is unknown) so the PLL can lock when the vendor u-boot did
not initialize these registers yet.
Fixes: b882964b376f21 ("clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20200501215717.735393-1-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
At the first time update_mute_led() gets called, if channels are already
muted, the temp value equals to led_value as 0, skipping the following
LED setting.
So set led_value to -1 as an uninitialized state, to update the correct
LED status at first time usage.
Fixes: 5d43001ae436 ("ASoC: SOF: acpi led support for switch controls") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Acked-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20200430091139.7003-1-kai.heng.feng@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the leds subnode names to match (^led-[0-9a-f]$|led)
It fixes:
meson-g12b-a311d-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-s922x-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-g12b-odroid-n2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nanopi-k2.dt.yaml: leds: 'stat' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-nexbox-a95x.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-odroidc2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-pro.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-meta.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-vega-s95-telos.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-hub.dt.yaml: leds: 'system' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxbb-wetek-play2.dt.yaml: leds: 'ethernet', 'system', 'wifi' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905x-libretech-cc.dt.yaml: leds: 'blue', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxl-s905d-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-rbox-pro.dt.yaml: leds: 'blue', 'red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-gxm-s912-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-sei610.dt.yaml: leds: 'bluetooth' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
meson-sm1-khadas-vim3l.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
If one of the two is a loadable module, the combined driver must
not be built-in:
aarch64-linux-ld: sound/soc/codecs/rt5682.o: in function `rt5682_sdw_hw_free':
rt5682.c:(.text+0xb34): undefined reference to `sdw_stream_remove_slave'
aarch64-linux-ld: sound/soc/codecs/rt5682.o: in function `rt5682_sdw_hw_params':
rt5682.c:(.text+0xe78): undefined reference to `sdw_stream_add_slave'
In particular, the soundwire driver must not be built-in if
CONFIG_I2C=m.
On error the function ti_bandgap_get_sensor_data() returns the error
code in ERR_PTR() but we only checked if the return value is NULL or
not. And, so we can dereference an error code inside ERR_PTR.
While at it, convert a check to IS_ERR_OR_NULL.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200424161944.6044-1-sudipm.mukherjee@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Old versions of gcc (tested on gcc-4.8) produce a warning for
correct code:
sound/soc/soc-compress.c: In function 'soc_compr_open':
sound/soc/soc-compress.c:75:28: error: 'component' is used uninitialized in this function [-Werror=uninitialized]
struct snd_soc_component *component, *save = NULL;
Change the for_each_rtd_components() macro to ensure 'component'
gets initialized to a value the compiler does not complain about.
Some of the chips supported by the pca953x driver need the most
significant bit in the address word set to automatically increment the
address pointer on subsequent reads and writes (example: PCA9505). With
this bit unset the same register is read multiple times on a multi-byte
read sequence. Other chips must not have this bit set and autoincrement
always (example: PCA9555).
Up to now this AI bit was interpreted to be part of the address, which
resulted in inconsistent regmap caching when a register was written with
AI set and then read without it. This happened for the PCA9505 in
pca953x_gpio_set_multiple() where pca953x_read_regs() bulk read from the
cache for registers 0x8-0xc and then wrote to registers 0x88-0x8c. (Side
note: reading 5 values from offset 0x8 yiels OP0 5 times because AI must
be set to get OP0-OP4, which is another bug that is resolved here as a
by-product.) The same problem happens when calls to gpio_set_value() and
gpio_set_array_value() were mixed.
With this patch the AI bit is always set for chips that support it. This
works as there are no code locations that make use of the behaviour with
AI unset (for the chips that support it).
Note that the call to pca953x_setup_gpio() had to be done a bit earlier
to make the NBANK macro work.
The history of this bug is a bit complicated. Commit b32cecb46bdc
("gpio: pca953x: Extract the register address mangling to single
function") changed which chips and functions are affected. Commit 3b00691cc46a ("gpio: pca953x: hack to fix 24 bit gpio expanders") used
some duct tape to make the driver at least appear to work. Commit 49427232764d ("gpio: pca953x: Perform basic regmap conversion")
introduced the caching. Commit b4818afeacbd ("gpio: pca953x: Add
set_multiple to allow multiple bits to be set in one write.") introduced
the .set_multiple() callback which didn't work for chips that need the
AI bit which was fixed later for some chips in 8958262af3fb ("gpio:
pca953x: Repair multi-byte IO address increment on PCA9575"). So I'm
sorry, I don't know which commit I should pick for a Fixes: line.
Tested-by: Marcel Gudert <m.gudert@eckelmann.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_POST and
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_PRE are active low. This means:
- asserting them requires setting the register value to 0
- de-asserting them requires setting the register value to 1
Set the register value accordingly for these two reset lines by setting
the inverted the register value compared to all other reset lines.
Use hdmi_pll_lvds_out as parent of the vid_pll_in_sel clock. It's not
easy to see that the vendor kernel does the same, but it actually does.
meson_clk_pll_ops in mainline still cannot fully recalculate all rates
from the HDMI PLL registers because some register bits (at the time of
writing it's unknown which bits are used for this) double the HDMI PLL
output rate (compared to simply considering M, N and FRAC) for some (but
not all) PLL settings.
Update the vid_pll_in_sel parent so our clock calculation works for
simple clock settings like the CVBS output (where no rate doubling is
going on). The PLL ops need to be fixed later on for more complex clock
settings (all HDMI rates).
Fixes: 6cb57c678bb70 ("clk: meson: meson8b: add the read-only video clock trees") Suggested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20200417184127.1319871-2-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When creating a consumer/supplier relationship between two devices,
make sure the supplier node is actually active. Otherwise this will
create a link relationship that will never be fulfilled. This, in the
worst case scenario, will hang the system during boot.
Note that, in practice, the fact that a device-tree represented
consumer/supplier relationship isn't fulfilled will not prevent devices
from successfully probing.
Fixes: a3e1d1a7f5fc ("of: property: Add functional dependency link from DT bindings") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Upon adding a new device from a DT node, we scan its properties and its
children's properties in order to create a consumer/supplier
relationship between the device and the property provider.
That said, it's possible for some of the node's children to be disabled,
which will create links that'll never be fulfilled.
To get around this, use the for_each_available_child_of_node() function
instead of for_each_available_node() when iterating over the node's
children.
Fixes: d4387cd11741 ("of: property: Create device links for all child-supplier depencencies") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
It has been reported that trying to send small packets of data could
produce a "inconsistent notification" warning.
It seems that in some circumstances, the number of frame queued in the
driver could greatly increase and exceed UCHAR_MAX. So the field
"buffered" from struct sta_priv can overflow.
Just increase the size of "bueffered" to fix the problem.
qdio_establish() calls qdio_setup_thinint() via qdio_setup_irq().
If the subsequent qdio_establish_thinint() fails, we miss to put the
DSCI again. Thus the DSCI isn't available for re-use. Given enough of
such errors, we could end up with having only the shared DSCI available.
Merge qdio_setup_thinint() into qdio_establish_thinint(), and deal with
such an error internally.
For rolling back after an error, qdio_establish() calls qdio_shutdown().
If the error occurs early enough, then the qdio_irq's state still is
QDIO_IRQ_STATE_INACTIVE and qdio_shutdown() does nothing.
But at _any_ point where qdio_establish() bails out in this way,
qdio_setup_irq() will have already replaced the IRQ handler. This then
won't be restored after an early error, and the device can end up being
returned to the device driver with qdio's IRQ handler still installed.
Slightly reorder qdio_setup_irq() so we can be 100% sure that the IRQ
handler was replaced. Then fix the bug in qdio_establish() by calling a
helper that rolls back only the IRQ handler modification.
Also use the new helper in qdio_shutdown() to keep things in sync, and
slightly clean up the locking while doing so.
This makes minor semantical changes, but holding setup_mutex gives us
sufficient leeway to eg. pull qdio_shutdown_thinint() outside of the
ccwdev lock's scope.
The linked list entry from FIFO is peeked at
queue_pending_output_urbs() but the actual element pop-out is
performed outside the spinlock, and it's potentially racy.
Do delete the link at the right place inside the spinlock.
For computation of the the next frame size current value of fs/fps and
accumulated fractional parts of fs/fps are used, where values are stored
in Q16.16 format. This is quite natural for computing frame size for
asynchronous endpoints driven by explicit feedback, since in this case
fs/fps is a value provided by the feedback endpoint and it's already in
the Q format. If an error is accumulated over time, the device can
adjust fs/fps value to prevent buffer overruns/underruns.
But for synchronous endpoints the accuracy provided by these computations
is not enough. Due to accumulated error the driver periodically produces
frames with incorrect size (+/- 1 audio sample).
This patch fixes this issue by implementing a different algorithm for
frame size computation. It is based on accumulating of the remainders
from division fs/fps and it doesn't accumulate errors over time. This
new method is enabled for synchronous and adaptive playback endpoints.
gasket_sysfs_register_store() invokes get_mapping(), which returns a
reference of the specified gasket_sysfs_mapping object to "mapping" with
increased refcnt.
When gasket_sysfs_register_store() returns, local variable "mapping"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The reference counting issue happens in one exception handling path of
gasket_sysfs_register_store(). When gasket_dev is NULL, the function
forgets to decrease the refcnt increased by get_mapping(), causing a
refcnt leak.
Fix this issue by calling put_mapping() when gasket_dev is NULL.
gasket_sysfs_put_attr() invokes get_mapping(), which returns a reference
of the specified gasket_sysfs_mapping object to "mapping" with increased
refcnt.
When gasket_sysfs_put_attr() returns, local variable "mapping" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
gasket_sysfs_put_attr(). When mapping attribute is unknown, the function
forgets to decrease the refcnt increased by get_mapping(), causing a
refcnt leak.
Fix this issue by calling put_mapping() when put attribute fails due to
unknown attribute.
As far as the device is concerned the dma address is the physical
address. There is no need to convert it to a physical address,
especially not using dma-direct internals that are not available
to drivers and which will interact badly with IOMMUs. Last but not
least the commit introducing it claimed to just fix a type issue,
but actually changed behavior.
Fixes: 6e37ccf78a532 ("firmware: qcom_scm: Use proper types for dma mappings") Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20200414123136.441454-1-hch@lst.de Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 963545357202 ("fuse: reduce allocation size for splice_write")
changed size of bufs array, so BUG_ON which checks the index of the array
shold also be fixed.
In virtiofs (unlike in regular fuse) processing of async replies is
serialized. This can result in a deadlock in rare corner cases when
there's a circular dependency between the completion of two or more async
replies.
Such a deadlock can be reproduced with xfstests:generic/503 if TEST_DIR ==
SCRATCH_MNT (which is a misconfiguration):
- Process A is waiting for page lock in worker thread context and blocked
(virtio_fs_requests_done_work()).
- Process B is holding page lock and waiting for pending writes to
finish (fuse_wait_on_page_writeback()).
- Write requests are waiting in virtqueue and can't complete because
worker thread is blocked on page lock (process A).
Fix this by creating a unique work_struct for each async reply that can
block (O_DIRECT read).
The rza1l_swio_entries referred to the wrong array rza1h_swio_pins,
which was intended to be rza1l_swio_pins. So let's fix it.
This is detected by the following gcc warning:
drivers/pinctrl/pinctrl-rza1.c:401:35: warning: ‘rza1l_swio_pins’
defined but not used [-Wunused-const-variable=]
static const struct rza1_swio_pin rza1l_swio_pins[] = {
^~~~~~~~~~~~~~~
Fixes: 039bc58e73b77723 ("pinctrl: rza1: Add support for RZ/A1L") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Link: https://lore.kernel.org/r/20200417111604.19143-1-yanaijie@huawei.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'size_t' type behaves differently on 64-bit architectures, and causes
compiler a warning of the sort "format '%u' expects argument of type
'unsigned int', but argument 3 has type 'size_t {aka long unsigned int}'".
This change adds the correct specifier for the 'align' field.
Fixes: 4538c18568099 ("iio: buffer-dmaengine: Report buffer length requirements") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MFW may make a call to qed and then to qedf for protocol statistics
while the function is still probing. If this happens it's possible that
some members of the struct qedf_ctx may not be fully initialized which can
result in a NULL pointer dereference or general protection fault.
To prevent this, add a new flag call QEDF_PROBING and set it when the
__qedf_probe() function is active. Then in the qedf_get_protocol_tlv_data()
function we can check if the function is still probing and return
immediantely before any uninitialized structures can be touched.
Link: https://lore.kernel.org/r/20200416084314.18851-9-skashyap@marvell.com Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 3d2613c4289f
("GPIO: gpio-dwapb: Enable platform driver binding to MFD driver")
introduced a use of the platform driver but missed to add the following line
to it:
MODULE_ALIAS("platform:gpio-dwapb");
Add this to get driver loaded automatically if platform device is registered.
Fixes: 8b8061fcbfae ("ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board") Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Cc: Icenowy Zheng <icenowy@aosc.io> Cc: Maxime Ripard <mripard@kernel.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
For an unreachable target, offload_work is not initialized and the endpoint
state is set to OFLDCONN_NONE. This results in a WARN_ON due to the check
of the work function field being set to zero.
Warning (unit_address_vs_reg): /oscillator@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@2: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/cpu_crit@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /reserved-memory/vpu_dma_mem_region: node has a reg or ranges property, but no unit name
Warning (simple_bus_reg): /soc/pinctrl@10005000: simple-bus unit address format error, expected "1000b000"
Warning (simple_bus_reg): /soc/interrupt-controller@10220000: simple-bus unit address format error, expected "10221000"
MT7621 has three assigned interrupts for the pcie. This
interrupts should properly being mapped taking into account
which devices are finally connected in which bus according
to link status. So the irq mappings should be as follows
according to link status (three bits indicating which devices
are link up):
* For PCIe Bus 1 slot 0:
- status = 0x2 || status = 0x6 => IRQ = pcie1_irq (24).
- status = 0x4 => IRQ = pcie2_irq (25).
- default => IRQ = pcie0_irq (23).
* For PCIe Bus 2 slot 0:
- status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25).
- default => IRQ = pcie1_irq (24).
* For PCIe Bus 2 slot 1:
- status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25).
- default => IRQ = pcie1_irq (24).
* For PCIe Bus 3 any slot:
- default => IRQ = pcie2_irq (25).
Because of this, the function 'of_irq_parse_and_map_pci' cannot
be used and we need to change device tree information from using
the 'interrupt-map' and 'interrupt-map-mask' properties into an
'interrupts' property to be able to get irq information from the
ports using the 'platform_get_irq' and storing an 'irq-map' into
the pcie driver data node to properly map correct irq using a
new 'mt7621_map_irq' function where this map will be read and the
correct irq returned.
The register based driver turned out to be unstable, specially on RPi3a+
but not limited to it. While a fix is being worked on, we roll back to
using firmware based scheme.
Fixes: e1dc2b2e1bef ("ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20200303173217.3987-1-nsaenzjulienne@suse.de Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the purgatory is a special stand-alone binary, various profiling
and sanitizing options must be disabled. Having these options enabled
typically will cause dependencies on various special symbols exported by
special libs / stubs used by these frameworks. Since the purgatory is
special, it is not linked against these stubs causing missing symbols in
the purgatory if these options are not disabled.
Sync the set of disabled profiling and sanitizing options with that from
drivers/firmware/efi/libstub/Makefile, adding
-DDISABLE_BRANCH_PROFILING to the CFLAGS and setting:
GCOV_PROFILE := n
UBSAN_SANITIZE := n
This fixes broken references to ftrace_likely_update() when
CONFIG_TRACE_BRANCH_PROFILING is enabled and to __gcov_init() and
__gcov_exit() when CONFIG_GCOV_KERNEL is enabled.
The subset test is not taking into account the unconfined exception
which will cause profile transitions in the stacked confinement
case to fail when no_new_privs is applied.
This fixes a regression introduced in the fix for
https://bugs.launchpad.net/bugs/1839037
If the peer is closed, we will never get more data, so
tcp_bpf_wait_data will get stuck forever. In case we passed
MSG_DONTWAIT to recv(), we get EAGAIN but we should actually get
0.
>From man 2 recv:
RETURN VALUE
When a stream socket peer has performed an orderly shutdown, the
return value will be 0 (the traditional "end-of-file" return).
This patch makes tcp_bpf_wait_data always return 1 when the peer
socket has been shutdown. Either we have data available, and it would
have returned 1 anyway, or there isn't, in which case we'll call
tcp_recvmsg which does the right thing in this situation.
Ensure that all scheduled work items have completed before continuing
with device removal and after further event scheduling has been
halted. This patch fixes a bug where a scheduled driver reset event
is processed following device removal.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 9495b7e92f71 ("driver core: platform: Initialize dma_parms for
platform devices") in v5.7-rc5 added allocation of dma_parms structure to
all platform devices. Then vb2_dma_contig_set_max_seg_size() have been
changed not to allocate dma_parms structure and rely on the one allocated
by the device core. Lets allocate the needed structure also for the
devices created for the 2 MFC device memory ports.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Suggested-by: Ulf Hansson <ulf.hansson@linaro.org> Fixes: 9495b7e92f71 ("driver core: platform: Initialize dma_parms for platform devices") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The adapter info MAD is used to send the client info and receive the host
info as a response. A persistent buffer is used and as such the client info
is overwritten after the response. During the course of a normal adapter
reset the client info is refreshed in the buffer in preparation for sending
the adapter info MAD.
However, in the special case of LPM where we reenable the CRQ instead of a
full CRQ teardown and reset we fail to refresh the client info in the
adapter info buffer. As a result, after Live Partition Migration (LPM) we
erroneously report the host's info as our own.
When sockhash gets destroyed while sockets are still linked to it, we will
walk the bucket lists and delete the links. However, we are not freeing the
list elements after processing them, leaking the memory.
The leak can be triggered by close()'ing a sockhash map when it still
contains sockets, and observed with kmemleak:
xfs_ifree_cluster() calls xfs_perag_get() at the beginning, but forgets to
call xfs_perag_put() in one failed path.
Add the missed function call to fix it.
Fixes: ce92464c180b ("xfs: make xfs_trans_get_buf return an error code") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently apparmor_sk_clone_security() does not check for existing
label/peer in the 'new' struct sock; it just overwrites it, if any
(with another reference to the label of the source sock.)
The label reference count leak is observed if apparmor_sock_graft()
is called previously: this sets the 'ctx->label' field by getting
a reference to the current label (later overwritten, without put.)
Apparently both calls are done on their own right, especially for
other LSMs, being introduced in 2010/2014, before apparmor socket
mediation in 2017 (see commits [1,2,3,4]).
So, it looks OK there! Let's fix the reference leak in apparmor.
Test-case:
---------
Exercise that code path enough to overflow label reference count.
While trying to use the lantiq_gswip driver on one of my boards I made
a mistake when specifying the phy-mode (because the out-of-tree driver
wants phy-mode "gmii" or "mii" for the internal PHYs). In this case the
following error is printed multiple times:
Unsupported interface: 3
While it gives at least a hint at what may be wrong it is not very user
friendly. Print the human readable phy-mode and also which port is
configured incorrectly (this hardware supports ports 0..6) to improve
the cases where someone made a mistake.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. If a task is attached to a unconfined profile that is not the
ns->unconfined profile then. Mode the mode is always reported
as -
$ ps -Z
LABEL PID TTY TIME CMD
unconfined 1287 pts/0 00:00:01 bash
test (-) 1892 pts/0 00:00:00 ps
instead of the correct value of (unconfined) as shown below
$ ps -Z
LABEL PID TTY TIME CMD
unconfined 2483 pts/0 00:00:01 bash
test (unconfined) 3591 pts/0 00:00:00 ps
2. if a task is confined by a stack of profiles that are unconfined
the output of label mode is again the incorrect value of (-) like
above, instead of (unconfined). This is because the visibile
profile count increment is skipped by the special casing of
unconfined.
Fixes: f1bd904175e8 ("apparmor: add the base fns() for domain labels") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When System.map was generated, the kernel used mksysmap to
filter the kernel symbols, but all the symbols with the
second letter 'L' in the kernel were filtered out, not just
the symbols starting with 'dot + L'.
For example:
ashimida@ubuntu:~/linux$ cat System.map |grep ' .L'
ashimida@ubuntu:~/linux$ nm -n vmlinux |grep ' .L' ffff0000088028e0 t bLength_show
...... ffff0000092e0408 b PLLP_OUTC_lock ffff0000092e0410 b PLLP_OUTA_lock
The original intent should be to filter out all local symbols
starting with '.L', so the dot should be escaped.
Fixes: 00902e984732 ("mksysmap: Add h8300 local symbol pattern") Signed-off-by: ashimida <ashimida@linux.alibaba.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the commit adding ntb_default_port_number() and
ntb_default_peer_port_number() entered the kernel there was no
users of it so it was impossible to tell what the API needed.
When a user finally landed a year later (ntb_pingpong) there were
more NTB topologies were created and no consideration was considered
to how other drivers had changed.
Now that there is a user it can be fixed to provide a sensible default
for the legacy drivers that do not implement ntb_{peer_}port_number().
Seeing ntb_pingpong doesn't check error codes returning EINVAL was also
not sensible.
Patches for ntb_pingpong and ntb_perf follow (which are broken
otherwise) to support hardware that doesn't have port numbers. This is
important not only to not break support with existing drivers but for
the cross link topology which, due to its perfect symmetry, cannot
assign unique port numbers to each side.
Fixes: 1e5301196a88 ("NTB: Add indexed ports NTB API") Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <allenbh@gmail.com> Tested-by: Alexander Fomichev <fomichev.ru@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes pingpong support for existing drivers that do not
implement ntb_default_port_number() and ntb_default_peer_port_number().
This is required for hardware (like the crosslink topology of
switchtec) which cannot assign reasonable port numbers to each port due
to its perfect symmetry.
Instead of picking the doorbell to use based on the the index of the
peer, we use the peer's port number. This is a bit clearer and easier
to understand.
Fixes: c7aeb0afdcc2 ("NTB: ntb_pp: Add full multi-port NTB API support") Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <allenbh@gmail.com> Tested-by: Alexander Fomichev <fomichev.ru@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if the allocation of ldata fails the error return path
does not kfree the allocated links object. Fix this by adding
an error exit return path that performs the necessary kfree'ing.
Fixes: 7864a79f37b5 ("ASoC: meson: add axg sound card support") Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Resource leak") Link: https://lore.kernel.org/r/20200604171216.60043-1-colin.king@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The u64_stats mechanism uses sequence counters to protect against 64-bit
values tearing on 32-bit architectures. Updating u64_stats is thus a
sequence counter write side critical section where preemption must be
disabled.
For mdiobus_stats_acct(), disable preemption upon the u64_stats update.
It is called from process context through mdiobus_read() and
mdiobus_write().
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If register_netdev(dev) fails, free_netdev(dev) needs
to be called, otherwise a memory leak will occur.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ctx internal buffer can only hold buflen amount of data, don't try
to copy over more than that. Also, initialize the context sg pointer
if we only have data in the context internal buffer, this can happen
when closing a hash with certain data amounts.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tegra firmware doesn't actually use any version numbers and passing -1
causes the existing firmware binaries not to be found. Use version 0 to
find the correct files.
Fixes: ef16dc278ec2 ("drm/nouveau/gr/gf100-: select implementation based on available FW") Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
- A platform should not be 'tristate', it should be a 'bool' symbol
like the other platforms, if only for consistency, and to avoid
surprises like this one.
- The clk Makefile does not traverse into the sprd subdirectory
if the platform is disabled but the drivers are enabled for
compile-testing.
Fixing either of the two would be sufficient to address the link failure,
but for correctness, both need to be changed.
The pages backing page-table allocations for SRMMU are allocated via
memblock as part of the "nocache" region initialisation during
srmmu_paging_init() and should not be freed even if a later call to
pgtable_pte_page_ctor() fails.
Remove the broken call to __free_page().
Cc: David S. Miller <davem@davemloft.net> Cc: Kirill A. Shutemov <kirill@shutemov.name> Fixes: 1ae9ae5f7df7 ("sparc: handle pgtable_page_ctor() fail") Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even in failed case of pm_runtime_get_sync(), the usage_count is
incremented. In order to keep the usage_count with correct value call
appropriate pm_runtime_put().
'mem=" option is an easy way to put high pressure on memory during
some test. Hence after applying the memory limit, instead of total
mem, the actual usable memory should be considered when reserving mem
for crashkernel. Otherwise the boot up may experience OOM issue.
E.g. it would reserve 4G prior to the change and 512M afterward, if
passing
crashkernel="2G-4G:384M,4G-16G:512M,16G-64G:1G,64G-128G:2G,128G-:4G",
and mem=5G on a 256G machine.
This issue is powerpc specific because it puts higher priority on
fadump and kdump reservation than on "mem=". Referring the following
code:
if (fadump_reserve_mem() == 0)
reserve_crashkernel();
...
/* Ensure that total memory size is page-aligned. */
limit = ALIGN(memory_limit ?: memblock_phys_mem_size(), PAGE_SIZE);
memblock_enforce_memory_limit(limit);
While on other arches, the effect of "mem=" takes a higher priority
and pass through memblock_phys_mem_size() before calling
reserve_crashkernel().
where its target list contains NB names ("FS0" & "FS1") rather than
FQDN ones ("FS0.FOO.COM" & "FS1.FOO.COM"), we end up connecting to
\FOO\share1 but server->hostname will have "FOO.COM". The reason is
because both "FS0" and "FS0.FOO.COM" resolve to same IP address and
they share same TCP server connection, but "FS0.FOO.COM" was the first
hostname set -- which is OK.
However, if the echo thread timeouts and we still have a good
connection to "FS0", in cifs_reconnect()
it successfully reconnects to "FS0" server but does not set up next
DFS target - which should be the same target server "\FS0\share1" -
and server->hostname remains set to "FS0.FOO.COM" rather than "FS0",
as reconn_inval_dfs_target() would have it set to "FS0" if called
earlier.
Finally, in __smb2_reconnect(), the reconnect of tcons would fail
because tcon->ses->server->hostname (FS0.FOO.COM) does not match DFS
target's hostname (FS0).
Fix that by calling reconn_inval_dfs_target() before
generic_ip_connect() so server->hostname will get updated correctly
prior to reconnecting its tcons in __smb2_reconnect().
With "cifs: handle hostnames that resolve to same ip in failover"
patch
- The above problem would not occur.
- We could save an DNS query to find out that they both resolve to
the same ip address.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log