An update from ieee802154 for your *net-next* tree:
Andy Shevchenko reworked the ca8210 driver to use the gpiod API and fixed
a few problems of the driver along the way.
* tag 'ieee802154-for-net-next-2025-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan-next:
dt-bindings: ieee802154: ca8210: Update polarity of the reset pin
ieee802154: ca8210: Switch to using gpiod API
ieee802154: ca8210: Get platform data via dev_get_platdata()
ieee802154: ca8210: Use proper setters and getters for bitwise types
====================
This series removes unnecessary of_get_phy_mode() calls from the stmmac
glue drivers. stmmac_probe_config_dt() / devm_stmmac_probe_config_dt()
already gets the interface mode using device_get_phy_mode() and stores
it in plat_dat->phy_interface.
Therefore, glue drivers using of_get_phy_mode() are just duplicating
the work that has already been done.
This series adjusts the glue drivers to remove their usage of
of_get_phy_mode().
====================
Russell King (Oracle) [Wed, 12 Mar 2025 09:21:07 +0000 (09:21 +0000)]
net: stmmac: sunxi: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Set gmac->interface from plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGx-005v0F-Ev@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Wed, 12 Mar 2025 09:21:02 +0000 (09:21 +0000)]
net: stmmac: sun8i: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
sun8i was using of_get_phy_mode() to set plat_dat->mac_interface, which
defaults to plat_dat->phy_interface when the mac-mode DT property is
not present. As nothing in arch/*/boot/dts sets the mac-mode property,
it is highly likely that these two will be identical, and thus there
is no need for this glue driver to set plat_dat->mac_interface.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGs-005v09-CD@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Wed, 12 Mar 2025 09:20:57 +0000 (09:20 +0000)]
net: stmmac: sti: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Pass plat_dat into sti_dwmac_parse_data(), and set dwmac->interface
from plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGn-005v02-7G@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Wed, 12 Mar 2025 09:20:52 +0000 (09:20 +0000)]
net: stmmac: rk: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Set bsp_priv->phy_iface from plat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGi-005uzx-3p@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Wed, 12 Mar 2025 09:20:47 +0000 (09:20 +0000)]
net: stmmac: meson8b: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Set dwmac->phy_mode from plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGd-005uzr-0C@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Wed, 12 Mar 2025 09:20:41 +0000 (09:20 +0000)]
net: stmmac: ipq806x: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Pass plat_dat into ipq806x_gmac_of_parse(), and set gmac->phy_mode from
plat_dat->phy_interface.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGX-005uzl-TQ@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Wed, 12 Mar 2025 09:20:36 +0000 (09:20 +0000)]
net: stmmac: anarion: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Rearrange the initialisation order so we can pass plat_dat into
anarion_config_dt(), thereby providing plat_dat->phy_interface as
necessary there.
Russell King (Oracle) [Wed, 12 Mar 2025 09:20:31 +0000 (09:20 +0000)]
net: stmmac: mediatek: remove of_get_phy_mode()
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it in platform code.
Initialise priv_plat->phy_mode from plat->phy_interface
inmediatek_dwmac_common_data().
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGN-005uzZ-NG@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_stmmac_probe_config_dt() already gets the PHY mode from firmware,
which is stored in plat_dat->phy_interface. Therefore, we don't need to
get it a second time in qcom_ethqos_probe(). Use
plat_dat->phy_interface to initialise ethqos->phy_mode.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tsIGI-005uzT-KB@rmk-PC.armlinux.org.uk Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Tue, 18 Mar 2025 11:10:20 +0000 (12:10 +0100)]
Merge tag 'batadv-next-pullrequest-20250313' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- drop batadv_priv_debug_log struct, by Sven Eckelmann
- adopt netdev_hold() / netdev_put(), by Eric Dumazet
- add support for jumbo frames, by Sven Eckelmann
- use consistent name for mesh interface, by Sven Eckelmann
- cleanup B.A.T.M.A.N. IV OGM aggregation handling,
by Sven Eckelmann (4 patches)
- add missing newlines for log macros, by Sven Eckelmann
* tag 'batadv-next-pullrequest-20250313' of git://git.open-mesh.org/linux-merge:
batman-adv: add missing newlines for log macros
batman-adv: Limit aggregation size to outgoing MTU
batman-adv: Use actual packet count for aggregated packets
batman-adv: Switch to bitmap helper for aggregation handling
batman-adv: Limit number of aggregated packets directly
batman-adv: Use consistent name for mesh interface
batman-adv: Add support for jumbo frames
batman-adv: adopt netdev_hold() / netdev_put()
batman-adv: Drop batadv_priv_debug_log struct
batman-adv: Start new development cycle
====================
The UDP tunnel GRO stage is source of measurable overhead for workload
based on UDP-encapsulated traffic: each incoming packets requires a full
UDP socket lookup and an indirect call.
In the most common setups a single UDP tunnel device is used. In such
case we can optimize both the lookup and the indirect call.
Patch 1 tracks per netns the active UDP tunnels and replaces the socket
lookup with a single destination port comparison when possible.
Patch 2 tracks the different types of UDP tunnels and replaces the
indirect call with a static one when there is a single UDP tunnel type
active.
I measure ~5% performance improvement in TCP over UDP tunnel stream
tests on top of this series.
Paolo Abeni [Tue, 11 Mar 2025 20:42:29 +0000 (21:42 +0100)]
udp_tunnel: use static call for GRO hooks when possible
It's quite common to have a single UDP tunnel type active in the
whole system. In such a case we can replace the indirect call for
the UDP tunnel GRO callback with a static call.
Add the related accounting in the control path and switch to static
call when possible. To keep the code simple use a static array for
the registered tunnel types, and size such array based on the kernel
config.
Paolo Abeni [Tue, 11 Mar 2025 20:42:28 +0000 (21:42 +0100)]
udp_tunnel: create a fastpath GRO lookup.
Most UDP tunnels bind a socket to a local port, with ANY address, no
peer and no interface index specified.
Additionally it's quite common to have a single tunnel device per
namespace.
Track in each namespace the UDP tunnel socket respecting the above.
When only a single one is present, store a reference in the netns.
When such reference is not NULL, UDP tunnel GRO lookup just need to
match the incoming packet destination port vs the socket local port.
The tunnel socket never sets the reuse[port] flag[s]. When bound to no
address and interface, no other socket can exist in the same netns
matching the specified local port.
Matching packets with non-local destination addresses will be
aggregated, and eventually segmented as needed - no behavior changes
intended.
Note that the UDP tunnel socket reference is stored into struct
netns_ipv4 for both IPv4 and IPv6 tunnels. That is intentional to keep
all the fastpath-related netns fields in the same struct and allow
cacheline-based optimization. Currently both the IPv4 and IPv6 socket
pointer share the same cacheline as the `udp_table` field.
====================
mlx5: Support setting a parent for a devlink rate node
This series by Carolina adds mlx5 support for the setting of a parent to
devlink rate nodes.
By introducing a hierarchical level to scheduling nodes, these changes
allow for more granular control over bandwidth allocation and isolation
of Virtual Functions.
Function renaming for parent setting on leafs:
- net/mlx5: Rename devlink rate parent set function for leaf nodes
Add support for hierarchy level tracking:
- net/mlx5: Introduce hierarchy level tracking on scheduling nodes
- net/mlx5: Preserve rate settings when creating a rate node
Support setting parent for rate nodes:
- net/mlx5: Add support for setting parent of nodes
====================
Carolina Jubran [Mon, 10 Mar 2025 21:26:56 +0000 (23:26 +0200)]
net/mlx5: Add support for setting parent of nodes
Introduce `mlx5_esw_devlink_rate_node_parent_set()` to allow assigning
a parent to scheduling nodes.
Implement `mlx5_esw_qos_node_update_parent()` and
`mlx5_esw_qos_node_validate_set_parent()` to enforce constraints on
node reassignment.
Don't allow reassignment of nodes with active rate objects.
Update `esw_qos_node_set_parent()` to handle cases where
the parent is NULL. A NULL parent indicates that the scheduling element
is attached to the root scheduling element, and since only rate nodes
can be connected to the root, this update is now necessary.
Carolina Jubran [Mon, 10 Mar 2025 21:26:55 +0000 (23:26 +0200)]
net/mlx5: Preserve rate settings when creating a rate node
Modify `esw_qos_create_node_sched_elem()` to receive max_rate and
bw_share values while maintaining the previous configuration.
This change is essential for the upcoming patch that will modify rate
nodes and requires the existing settings to be preserved unless
explicitly changed.
Carolina Jubran [Mon, 10 Mar 2025 21:26:54 +0000 (23:26 +0200)]
net/mlx5: Introduce hierarchy level tracking on scheduling nodes
Add a `level` field to `mlx5_esw_sched_node` to track the hierarchy
depth of each scheduling node. This allows enforcement of the
scheduling depth constraints based on `log_esw_max_sched_depth`.
Modify `esw_qos_node_set_parent()` and `__esw_qos_alloc_node()` to
correctly assign hierarchy levels. Ensure that nodes inherit their
parent’s level incrementally.
Carolina Jubran [Mon, 10 Mar 2025 21:26:53 +0000 (23:26 +0200)]
net/mlx5: Rename devlink rate parent set function for leaf nodes
Rename `mlx5_esw_devlink_rate_parent_set()` to
`mlx5_esw_devlink_rate_leaf_parent_set()` to distinguish setting a
parent for leafs from nodes, which is not yet supported.
Paolo Abeni [Tue, 18 Mar 2025 09:25:24 +0000 (10:25 +0100)]
Merge branch 'bnxt_en-driver-update'
Michael Chan says:
====================
bnxt_en: Driver update
This patchset contains these updates to the driver:
1. New ethtool coredump type for FW to include cached context for live dump.
2. Support ENABLE_ROCE devlink generic parameter.
3. Support capability change flag from FW.
4. FW interface update.
5. Support .set_module_eeprom_by_page().
====================
Damodharam Ammepalli [Mon, 10 Mar 2025 18:31:29 +0000 (11:31 -0700)]
bnxt_en: add .set_module_eeprom_by_page() support
Add support for .set_module_eeprom_by_page() callback
which implements generic solution for modules eeprom access.
This implementation also supports CMIS 5.0.3 compliant
eeprom FW download.
In preparation for adding .set_module_eeprom_by_page(), extract the
common error checking done in bnxt_get_module_eeprom_by_page() into
a new common function that can be re-used for
.set_module_eeprom_by_page().
shantiprasad shettar [Mon, 10 Mar 2025 18:31:26 +0000 (11:31 -0700)]
bnxt_en: Query FW parameters when the CAPS_CHANGE bit is set
Newer FW can set the CAPS_CHANGE flag during ifup if some capabilities
or configurations have changed. For example, the CoS queue
configurations may have changed. Support this new flag by treating it
almost like FW reset. The driver will essentially rediscover all
features and capabilities, reconfigure all backing store context memory,
reset everything to default, and reserve all resources.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: shantiprasad shettar <shantiprasad.shettar@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20250310183129.3154117-5-michael.chan@broadcom.com Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Michael Chan [Mon, 10 Mar 2025 18:31:24 +0000 (11:31 -0700)]
bnxt_en: Refactor bnxt_hwrm_nvm_req()
bnxt_hwrm_nvm_req() first searches the nvm_params[] array for the
NVM parameter to set or get. The array entry contains all the
NVM information about that parameter. The information is then used
to send the FW message to set or get the parameter.
Refactor it to only do the array search in bnxt_hwrm_nvm_req() and
pass the array entry to the new function __bnxt_hwrm_nvm_req() to
send the FW message. The next patch will be able to use the new
function.
Vasuthevan Maheswaran [Mon, 10 Mar 2025 18:31:23 +0000 (11:31 -0700)]
bnxt_en: Add support for a new ethtool dump flag 3
When doing a live coredump with ethtool -w, the context data cached
in the NIC is not dumped by the FW by default. The reason is that
retrieving this cached context data with traffic running may cause
problems. Add a new dump flag 3 to allow the option to include this
cached context data which may be useful in some debug scenarios.
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com> Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com> Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com> Signed-off-by: Vasuthevan Maheswaran <vasuthevan.maheswaran@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20250310183129.3154117-2-michael.chan@broadcom.com Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
====================
Intel Wired LAN Driver Updates 2025-03-10 (ice, ixgbe)
For ice:
Paul adds generic checksum support for E830 devices.
Karol refactors PTP code related to E825C; simplifying PHY register info
struct, utilizing GENMASK, removing unused defines, etc.
For ixgbe:
Piotr adds PTP support for E610 devices.
Jedrzej adds reporting when overheating is detected on E610 devices.
The following are changes since commit 8ef890df4031121a94407c84659125cbccd3fdbe:
net: move misc netdev_lock flavors to a separate header
and are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue 100GbE
====================
Jedrzej Jagielski [Mon, 10 Mar 2025 17:44:59 +0000 (10:44 -0700)]
ixgbe: add support for thermal sensor event reception
E610 NICs unlike the previous devices utilising ixgbe driver
are notified in the case of overheating by the FW ACI event.
In event of overheat when threshold is exceeded, FW suspends all
traffic and sends overtemp event to the driver. Then driver
logs appropriate message and disables the adapter instance.
The card remains in that state until the platform is rebooted.
This approach is a solution to the fact current version of the
E610 FW doesn't support reading thermal sensor data by the
SW. So give to user at least any info that overtemp event
has occurred, without interface disappearing from the OS
without any note.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Jeremiah Lokan <jeremiahx.j.lokan@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250310174502.3708121-7-anthony.l.nguyen@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Piotr Kwapulinski [Mon, 10 Mar 2025 17:44:58 +0000 (10:44 -0700)]
ixgbe: add PTP support for E610 device
Add PTP support for E610 adapter. The E610 is based on X550 and adds
firmware managed link, enhanced security capabilities and support for
updated server manageability. It does not introduce any new PTP features
compared to X550.
Reviewed-by: Milena Olech <milena.olech@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Tested-by: Bharath R <bharath.r@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250310174502.3708121-6-anthony.l.nguyen@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Karol Kolacinski [Mon, 10 Mar 2025 17:44:57 +0000 (10:44 -0700)]
ice: E825C PHY register cleanup
Minor PTP register refactor, including logical grouping E825C 1-step
timestamping registers. Remove unused register definitions
(PHY_REG_GPCS_BITSLIP, PHY_REG_REVISION).
Also, apply preferred GENMASK macro (instead of ICE_M) for register
fields definition affected by this patch.
Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250310174502.3708121-5-anthony.l.nguyen@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Karol Kolacinski [Mon, 10 Mar 2025 17:44:56 +0000 (10:44 -0700)]
ice: Refactor E825C PHY registers info struct
Simplify ice_phy_reg_info_eth56g struct definition to include base
address for the very first quad. Use base address info and 'step'
value to determine address for specific PHY quad.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250310174502.3708121-4-anthony.l.nguyen@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Karol Kolacinski [Mon, 10 Mar 2025 17:44:55 +0000 (10:44 -0700)]
ice: rename ice_ptp_init_phc_eth56g function
Refactor the code by changing ice_ptp_init_phc_eth56g function
name to ice_ptp_init_phc_e825, to be consistent with the naming pattern
for other devices.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250310174502.3708121-3-anthony.l.nguyen@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paul Greenwalt [Mon, 10 Mar 2025 17:44:54 +0000 (10:44 -0700)]
ice: Add E830 checksum offload support
E830 supports raw receive and generic transmit checksum offloads.
Raw receive checksum support is provided by hardware calculating the
checksum over the whole packet, regardless of type. The calculated
checksum is provided to driver in the Rx flex descriptor. Then the driver
assigns the checksum to skb->csum and sets skb->ip_summed to
CHECKSUM_COMPLETE.
Generic transmit checksum support is provided by hardware calculating the
checksum given two offsets: the start offset to begin checksum calculation,
and the offset to insert the calculated checksum in the packet. Support is
advertised to the stack using NETIF_F_HW_CSUM feature.
E830 has the following limitations when both generic transmit checksum
offload and TCP Segmentation Offload (TSO) are enabled:
1. Inner packet header modification is not supported. This restriction
includes the inability to alter TCP flags, such as the push flag. As a
result, this limitation can impact the receiver's ability to coalesce
packets, potentially degrading network throughput.
2. The Maximum Segment Size (MSS) is limited to 1023 bytes, which prevents
support of Maximum Transmission Unit (MTU) greater than 1063 bytes.
Therefore NETIF_F_HW_CSUM and NETIF_F_ALL_TSO features are mutually
exclusive. NETIF_F_HW_CSUM hardware feature support is indicated but is not
enabled by default. Instead, IP checksums and NETIF_F_ALL_TSO are the
defaults. Enforcement of mutual exclusivity of NETIF_F_HW_CSUM and
NETIF_F_ALL_TSO is done in ice_set_features(). Mutual exclusivity
of IP checksums and NETIF_F_HW_CSUM is handled by netdev_fix_features().
When NETIF_F_HW_CSUM is requested the provided skb->csum_start and
skb->csum_offset are passed to hardware in the Tx context descriptor
generic checksum (GCS) parameters. Hardware calculates the 1's complement
from skb->csum_start to the end of the packet, and inserts the result in
the packet at skb->csum_offset.
Co-developed-by: Alice Michael <alice.michael@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Co-developed-by: Eric Joyner <eric.joyner@intel.com> Signed-off-by: Eric Joyner <eric.joyner@intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250310174502.3708121-2-anthony.l.nguyen@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
====================
net: phy: Rework linkmodes handling in a dedicated file
This is V5 of the phy_caps series. In a nutshell, this series reworks the way
we maintain the list of speed/duplex capablities for each linkmode so that we
no longer have multiple definition of these associations.
That will help making sure that when people add new linkmodes in
include/uapi/linux/ethtool.h, they don't have to update phylib and phylink as
well, making the process more straightforward and less error-prone.
It also generalises the phy_caps interface to be able to lookup linkmodes
from phy_interface_t, which is needed for the multi-port work I've been working
on for a while.
This V5 addresse Russell's and Paolo's reviews, namely :
- Error out when encountering an unknown SPEED_XXX setting
It prints an error and fails to initialize phylib. I've tested by
introducing a dummy 1.6T speed, I guess it's only a matter of time
before that actually happens :)
- Deal more gracefully with the fixed-link settings, keeping some level of
compatibility with what we had before by making sure we report a
single BaseT mode like before.
Maxime Chevallier [Fri, 7 Mar 2025 17:36:10 +0000 (18:36 +0100)]
net: phylink: Use phy_caps to get an interface's capabilities and modes
Phylink has internal code to get the MAC capabilities of a given PHY
interface (what are the supported speed and duplex).
Extract that into phy_caps, but use the link_capa for conversion. Add an
internal phylink helper for the link caps -> mac caps conversion, and
use this in phylink_caps_to_linkmodes().
Maxime Chevallier [Fri, 7 Mar 2025 17:36:09 +0000 (18:36 +0100)]
net: phylink: Convert capabilities to linkmodes using phy_caps
phylink_caps_to_linkmodes() is used to derive a list of linkmodes that
can be conceivably exposed using a given set of speeds and duplex
through phylink's MAC capabilities.
This list can be derived from the link_caps array in phy_caps, provided
we convert the MAC capabilities into a LINK_CAPA bitmask first.
Introduce an internal phylink helper phylink_caps_to_link_caps() to
convert from MAC capabilities into phy_caps, then phy_caps_linkmodes()
to do the link_caps -> linkmodes conversion.
This avoids having to update phylink for every new linkmode.
Maxime Chevallier [Fri, 7 Mar 2025 17:36:08 +0000 (18:36 +0100)]
net: phylink: Add a mapping between MAC_CAPS and LINK_CAPS
phylink allows MAC drivers to report the capabilities in terms of speed,
duplex and pause support. This is done through a dedicated set of enum
values in the form of the MAC_ capabilities. They are very close to what
the LINK_CAPA_xxx can express, with the difference that LINK_CAPA don't
have any information about Pause/Asym Pause support.
To prepare converting phylink to using the phy_caps, add the mapping
between MAC capabilities and phy_caps. While doing so, we move the
phylink_caps_params array up a bit to simplify future commits.
Maxime Chevallier [Fri, 7 Mar 2025 17:36:06 +0000 (18:36 +0100)]
net: phylink: Use phy_caps_lookup for fixed-link configuration
When phylink creates a fixed-link configuration, it finds a matching
linkmode to set as the advertised, lp_advertising and supported modes
based on the speed and duplex of the fixed link.
Use the newly introduced phy_caps_lookup to get these modes instead of
phy_lookup_settings(). This has the side effect that the matched
settings and configured linkmodes may now contain several linkmodes (the
intersection of supported linkmodes from the phylink settings and the
linkmodes that match speed/duplex) instead of the one from
phy_lookup_settings().
Maxime Chevallier [Fri, 7 Mar 2025 17:36:05 +0000 (18:36 +0100)]
net: phy: phy_device: Use link_capabilities lookup for PHY aneg config
When configuring PHY advertising with autoneg disabled, we lookd for an
exact linkmode to advertise and configure for the requested Speed and
Duplex, specially at or over 1G.
Using phy_caps_lookup allows us to build a list of the supported
linkmodes at that speed that we can advertise instead of the first mode
that matches.
Maxime Chevallier [Fri, 7 Mar 2025 17:36:04 +0000 (18:36 +0100)]
net: phy: phy_caps: Allow looking-up link caps based on speed and duplex
As the link_caps array is efficient for <speed,duplex> lookups,
implement a function for speed/duplex lookups that matches a given
mask. This replicates to some extent the phy_lookup_settings()
behaviour, matching full link_capabilities instead of a single linkmode.
phy.c's phy_santize_settings() and phylink's
phylink_ethtool_ksettings_set() performs such lookup using the
phy_settings table, but are only interested in the actual speed/duplex
that were matched, rathet than the individual linkmode.
Similar to phy_lookup_settings(), the newly introduced phy_caps_lookup()
will run through the link_caps[] array by descending speed/duplex order.
If the link_capabilities for a given <speed/duplex> tuple intersects the
passed linkmodes, we consider that a match.
Similar to phy_lookup_settings(), we also allow passing an 'exact'
boolean, allowing non-exact match. Here, we MUST always match the
linkmodes mask, but we allow matching on lower speed settings.
Maxime Chevallier [Fri, 7 Mar 2025 17:36:03 +0000 (18:36 +0100)]
net: phy: phy_caps: Implement link_capabilities lookup by linkmode
In several occasions, phylib needs to lookup a set of matching speed and
duplex against a given linkmode set. Instead of relying on the
phy_settings array and thus iterate over the whole linkmodes list, use
the link_capabilities array to lookup these matches, as we aren't
interested in the actual link setting that matches but rather the speed
and duplex for that setting.
Maxime Chevallier [Fri, 7 Mar 2025 17:36:02 +0000 (18:36 +0100)]
net: phy: phy_caps: Introduce phy_caps_valid
With the link_capabilities array, it's trivial to validate a given mask
againts a <speed, duplex> tuple. Create a helper for that purpose, and
use it to replace a phy_settings lookup in phy_check_valid();
Maxime Chevallier [Fri, 7 Mar 2025 17:36:01 +0000 (18:36 +0100)]
net: phy: phy_caps: Move __set_linkmode_max_speed to phy_caps
Convert the __set_linkmode_max_speed to use the link_capabilities array.
This makes it easy to clamp the linkmodes to a given max speed.
Introduce a new helper phy_caps_linkmode_max_speed to replace the
previous one that used phy_settings.
Maxime Chevallier [Fri, 7 Mar 2025 17:36:00 +0000 (18:36 +0100)]
net: phy: phy_caps: Move phy_speeds to phy_caps
Use the newly introduced link_capabilities array to derive the list of
possible speeds when given a combination of linkmodes. As
link_capabilities is indexed by speed, we don't have to iterate the
whole phy_settings array.
Maxime Chevallier [Fri, 7 Mar 2025 17:35:59 +0000 (18:35 +0100)]
net: phy: Use an internal, searchable storage for the linkmodes
The canonical definition for all the link modes is in linux/ethtool.h,
which is complemented by the link_mode_params array stored in
net/ethtool/common.h . That array contains all the metadata about each
of these modes, including the Speed and Duplex information.
Phylib and phylink needs that information as well for internal
management of the link, which was done by duplicating that information
in locally-stored arrays and lookup functions. This makes it easy for
developpers adding new modes to forget modifying phylib and phylink
accordingly.
However, the link_mode_params array in net/ethtool/common.c is fairly
inefficient to search through, as it isn't sorted in any manner. Phylib
and phylink perform a lot of lookup operations, mostly to filter modes
by speed and/or duplex.
We therefore introduce the link_caps private array in phy_caps.c, that
indexes linkmodes in a more efficient manner. Each element associated a
tuple <speed, duplex> to a bitfield of all the linkmodes runs at these
speed/duplex.
We end-up with an array that's fairly short, easily addressable and that
it optimised for the typical use-cases of phylib/phylink.
That array is initialized at the same time as phylib. As the
link_mode_params array is part of the net stack, which phylink depends
on, it should always be accessible from phylib.
Maxime Chevallier [Fri, 7 Mar 2025 17:35:58 +0000 (18:35 +0100)]
net: ethtool: Export the link_mode_params definitions
link_mode_params contains a lookup table of all 802.3 link modes that
are currently supported with structured data about each mode's speed,
duplex, number of lanes and mediums.
As a preparation for a port representation, export that table for the
rest of the net stack to use.
====================
net: stmmac: avoid unnecessary work in stmmac_release()/stmmac_dvr_remove()
This small series is a subset of a RFC I sent earlier. These two
patches remove code that is unnecessary and/or wrong in these paths.
Details in each commit.
====================
Russell King (Oracle) [Mon, 10 Mar 2025 12:31:30 +0000 (12:31 +0000)]
net: stmmac: remove unnecessary stmmac_mac_set() in stmmac_release()
stmmac_release() calls phylink_stop() and then goes on to call
stmmac_mac_set(, false). However, phylink_stop() will call
stmmac_mac_link_down() before returning, which will do this work.
Remove this unnecessary call.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Furong Xu <0x1207@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1trcI6-005rn8-GV@rmk-PC.armlinux.org.uk Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Mon, 10 Mar 2025 12:31:25 +0000 (12:31 +0000)]
net: stmmac: remove redundant racy tear-down in stmmac_dvr_remove()
While the network device is registered, it is published to userspace,
and thus userspace can change its state. This means calling
functions such as stmmac_stop_all_dma() and stmmac_mac_set() are
racy.
Moreover, unregister_netdev() will unpublish the network device, and
then if appropriate call the .ndo_stop() method, which is
stmmac_release(). This will first call phylink_stop() which will
synchronously take the link down, resulting in stmmac_mac_link_down()
and stmmac_mac_set(, false) being called.
stmmac_release() will also call stmmac_stop_all_dma().
Consequently, neither of these two functions need to called prior
to unregister_netdev() as that will safely call paths that will
result in this work being done if necessary.
Remove these redundant racy calls.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Furong Xu <0x1207@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1trcI1-005rn2-CZ@rmk-PC.armlinux.org.uk Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King (Oracle) [Mon, 10 Mar 2025 11:10:52 +0000 (11:10 +0000)]
net: phylink: expand on .pcs_config() method documentation
Expand on the requirements of the .pcs_config() method documentation,
specifically mentioning that it should cause minimal disruption to
an established link, and that it should return a positive non-zero
value when requiring the .pcs_an_restart() method to be called.
Philipp Hahn [Mon, 10 Mar 2025 10:17:35 +0000 (11:17 +0100)]
cdc_ether|r8152: ThinkPad Hybrid USB-C/A Dock quirk
Lenovo ThinkPad Hybrid USB-C with USB-A Dock (17ef:a359) is affected by
the same problem as the Lenovo Powered USB-C Travel Hub (17ef:721e):
Both are based on the Realtek RTL8153B chip used to use the cdc_ether
driver. However, using this driver, with the system suspended the device
constantly sends pause-frames as soon as the receive buffer fills up.
This causes issues with other devices, where some Ethernet switches stop
forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
====================
mlx5: Support HWS flow meter/sampler actions in FS core
This series by Moshe adds support for flow meter and flow sampler HW
Steering actions in FS core level. As these actions can be shared by
multiple rules, these patches use refcounts to manage the HWS actions
sharing in FS core level.
====================
Moshe Shemesh [Sun, 9 Mar 2025 18:07:43 +0000 (20:07 +0200)]
net/mlx5: fs, add support for dest flow sampler HWS action
Add support for HW Steering action of flow sampler destination. For each
flow sampler created cache the hws action by sampler id as a key. Hold
refcount for each rule using the cached action.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1741543663-22123-4-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Moshe Shemesh [Sun, 9 Mar 2025 18:07:42 +0000 (20:07 +0200)]
net/mlx5: fs, add support for flow meters HWS action
Add support for HW Steering action of flow meter range. Flow meters
range can use one HWS action for the whole range. Thus, share a cached
HWS action among rules that use same flow meter object range. Hold
refcount for each rule using the cached action.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1741543663-22123-3-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Moshe Shemesh [Sun, 9 Mar 2025 18:07:41 +0000 (20:07 +0200)]
net/mlx5: fs, add API for sharing HWS action by refcount
Counters HWS actions are shared using refcount, to create action on
demand by flow steering rule and destroy only when no rules are using
the action. The method is extensible to other HWS action types, such as
flow meter and sampler actions, in the downstream patches.
Add an API to facilitate the reuse of get/put logic for HWS actions
shared by refcount.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1741543663-22123-2-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
David S. Miller [Mon, 17 Mar 2025 13:57:14 +0000 (13:57 +0000)]
Merge branch 'tcp-accecn'
Chia-Yu Chang says:
====================
AccECN protocol preparation patch series
Please find the v7
v7 (03-Mar-2025)
- Move 2 new patches added in v6 to the next AccECN patch series
v6 (27-Dec-2024)
- Avoid removing removing the potential CA_ACK_WIN_UPDATE in ack_ev_flags of patch #1 (Eric Dumazet <edumazet@google.com>)
- Add reviewed-by tag in patches #2, #3, #4, #5, #6, #7, #8, #12, #14
- Foloiwng 2 new pathces are added after patch #9 (Patch that adds SKB_GSO_TCP_ACCECN)
* New patch #10 to replace exisiting SKB_GSO_TCP_ECN with SKB_GSO_TCP_ACCECN in the driver to avoid CWR flag corruption
* New patch #11 adds AccECN for virtio by adding new negotiation flag (VIRTIO_NET_F_HOST/GUEST_ACCECN) in feature handshake and translating Accurate ECN GSO flag between virtio_net_hdr (VIRTIO_NET_HDR_GSO_ACCECN) and skb header (SKB_GSO_TCP_ACCECN)
- Add detailed changelog and comments in #13 (Eric Dumazet <edumazet@google.com>)
- Move patch #14 to the next AccECN patch series (Eric Dumazet <edumazet@google.com>)
v5 (5-Nov-2024)
- Add helper function "tcp_flags_ntohs" to preserve last 2 bytes of TCP flags of patch #4 (Paolo Abeni <pabeni@redhat.com>)
- Fix reverse X-max tree order of patches #4, #11 (Paolo Abeni <pabeni@redhat.com>)
- Rename variable "delta" as "timestamp_delta" of patch #2 fo clariety
- Remove patch #14 in this series (Paolo Abeni <pabeni@redhat.com>, Joel Granados <joel.granados@kernel.org>)
v4 (21-Oct-2024)
- Fix line length warning of patches #2, #4, #8, #10, #11, #14
- Fix spaces preferred around '|' (ctx:VxV) warning of patch #7
- Add missing CC'ed of patches #4, #12, #14
v3 (19-Oct-2024)
- Fix build error in v2
v2 (18-Oct-2024)
- Fix warning caused by NETIF_F_GSO_ACCECN_BIT in patch #9 (Jakub Kicinski <kuba@kernel.org>)
The full patch series can be found in
https://github.com/L4STeam/linux-net-next/commits/upstream_l4steam/
The Accurate ECN draft can be found in
https://datatracker.ietf.org/doc/html/draft-ietf-tcpm-accurate-ecn-28
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:52 +0000 (23:38 +0100)]
tcp: Pass flags to __tcp_send_ack
Accurate ECN needs to send custom flags to handle IP-ECN
field reflection during handshake.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:51 +0000 (23:38 +0100)]
tcp: add new TCP_TW_ACK_OOW state and allow ECN bits in TOS
ECN bits in TOS are always cleared when sending in ACKs in TW. Clearing
them is problematic for TCP flows that used Accurate ECN because ECN bits
decide which service queue the packet is placed into (L4S vs Classic).
Effectively, TW ACKs are always downgraded from L4S to Classic queue
which might impact, e.g., delay the ACK will experience on the path
compared with the other packets of the flow.
Change the TW ACK sending code to differentiate:
- In tcp_v4_send_reset(), commit ba9e04a7ddf4f ("ip: fix tos reflection
in ack and reset packets") cleans ECN bits for TW reset and this is
not affected.
- In tcp_v4_timewait_ack(), ECN bits for all TW ACKs are cleaned. But now
only ECN bits of ACKs for oow data or paws_reject are cleaned, and ECN
bits of other ACKs will not be cleaned.
- In tcp_v4_reqsk_send_ack(), commit 66b13d99d96a1 ("ipv4: tcp: fix TOS
value in ACK messages sent from TIME_WAIT") did not clean ECN bits of
ACKs for oow data or paws_reject. But now the ECN bits rae cleaned for
these ACKs.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:50 +0000 (23:38 +0100)]
tcp: AccECN support to tcp_add_backlog
AE flag needs to be preserved for AccECN.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:49 +0000 (23:38 +0100)]
gro: prevent ACE field corruption & better AccECN handling
There are important differences in how the CWR field behaves
in RFC3168 and AccECN. With AccECN, CWR flag is part of the
ACE counter and its changes are important so adjust the flags
changed mask accordingly.
Also, if CWR is there, set the Accurate ECN GSO flag to avoid
corrupting CWR flag somewhere.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:48 +0000 (23:38 +0100)]
gso: AccECN support
Handling the CWR flag differs between RFC 3168 ECN and AccECN.
With RFC 3168 ECN aware TSO (NETIF_F_TSO_ECN) CWR flag is cleared
starting from 2nd segment which is incompatible how AccECN handles
the CWR flag. Such super-segments are indicated by SKB_GSO_TCP_ECN.
With AccECN, CWR flag (or more accurately, the ACE field that also
includes ECE & AE flags) changes only when new packet(s) with CE
mark arrives so the flag should not be changed within a super-skb.
The new skb/feature flags are necessary to prevent such TSO engines
corrupting AccECN ACE counters by clearing the CWR flag (if the
CWR handling feature cannot be turned off).
If NIC is completely unaware of RFC3168 ECN (doesn't support
NETIF_F_TSO_ECN) or its TSO engine can be set to not touch CWR flag
despite supporting also NETIF_F_TSO_ECN, TSO could be safely used
with AccECN on such NIC. This should be evaluated per NIC basis
(not done in this patch series for any NICs).
For the cases, where TSO cannot keep its hands off the CWR flag,
a GSO fallback is provided by this patch.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:47 +0000 (23:38 +0100)]
tcp: helpers for ECN mode handling
Create helpers for TCP ECN modes. No functional changes.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rename tcp_ecn_check_ce to tcp_data_ecn_check as it is
called only for data segments, not for ACKs (with AccECN,
also ACKs may get ECN bits).
The extra "layer" in tcp_ecn_check_ce() function just
checks for ECN being enabled, that can be moved into
tcp_ecn_field_check rather than having the __ variant.
No functional changes.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:44 +0000 (23:38 +0100)]
tcp: extend TCP flags to allow AE bit/ACE field
With AccECN, there's one additional TCP flag to be used (AE)
and ACE field that overloads the definition of AE, CWR, and
ECE flags. As tcp_flags was previously only 1 byte, the
byte-order stuff needs to be added to it's handling.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chia-Yu Chang [Wed, 5 Mar 2025 22:38:43 +0000 (23:38 +0100)]
tcp: use BIT() macro in include/net/tcp.h
Use BIT() macro for TCP flags field and TCP congestion control
flags that will be used by the congestion control algorithm.
No functional changes.
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Ilpo Järvinen <ij@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:42 +0000 (23:38 +0100)]
tcp: create FLAG_TS_PROGRESS
Whenever timestamp advances, it declares progress which
can be used by the other parts of the stack to decide that
the ACK is the most recent one seen so far.
AccECN will use this flag when deciding whether to use the
ACK to update AccECN state or not.
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 5 Mar 2025 22:38:41 +0000 (23:38 +0100)]
tcp: reorganize tcp_in_ack_event() and tcp_count_delivered()
- Move tcp_count_delivered() earlier and split tcp_count_delivered_ce()
out of it
- Move tcp_in_ack_event() later
- While at it, remove the inline from tcp_in_ack_event() and let
the compiler to decide
Accurate ECN's heuristics does not know if there is going
to be ACE field based CE counter increase or not until after
rtx queue has been processed. Only then the number of ACKed
bytes/pkts is available. As CE or not affects presence of
FLAG_ECE, that information for tcp_in_ack_event is not yet
available in the old location of the call to tcp_in_ack_event().
Signed-off-by: Ilpo Järvinen <ij@kernel.org> Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guangguan Wang [Tue, 4 Mar 2025 12:43:04 +0000 (20:43 +0800)]
net/smc: use the correct ndev to find pnetid by pnetid table
When using smc_pnet in SMC, it will only search the pnetid in the
base_ndev of the netdev hierarchy(both HW PNETID and User-defined
sw pnetid). This may not work for some scenarios when using SMC in
container on cloud environment.
In container, there have choices of different container network,
such as directly using host network, virtual network IPVLAN, veth,
etc. Different choices of container network have different netdev
hierarchy. Examples of netdev hierarchy show below. (eth0 and eth1
in host below is the netdev directly related to the physical device).
_______________________________
| _________________ |
| |POD | |
| | | |
| | eth0_________ | |
| |____| |__| |
| | | |
| | | |
| eth1|base_ndev| eth0_______ |
| | | | RDMA ||
| host |_________| |_______||
---------------------------------
netdev hierarchy if directly using host network
________________________________
| _________________ |
| |POD __________ | |
| | |upper_ndev| | |
| |eth0|__________| | |
| |_______|_________| |
| |lower netdev |
| __|______ |
| eth1| | eth0_______ |
| |base_ndev| | RDMA ||
| host |_________| |_______||
---------------------------------
netdev hierarchy if using IPVLAN
_______________________________
| _____________________ |
| |POD _________ | |
| | |base_ndev|| |
| |eth0(veth)|_________|| |
| |____________|________| |
| |pairs |
| _______|_ |
| | | eth0_______ |
| veth|base_ndev| | RDMA ||
| |_________| |_______||
| _________ |
| eth1|base_ndev| |
| host |_________| |
---------------------------------
netdev hierarchy if using veth
Due to some reasons, the eth1 in host is not RDMA attached netdevice,
pnetid is needed to map the eth1(in host) with RDMA device so that POD
can do SMC-R. Because the eth1(in host) is managed by CNI plugin(such
as Terway, network management plugin in container environment), and in
cloud environment the eth(in host) can dynamically be inserted by CNI
when POD create and dynamically be removed by CNI when POD destroy and
no POD related to the eth(in host) anymore. It is hard to config the
pnetid to the eth1(in host). But it is easy to config the pnetid to the
netdevice which can be seen in POD. When do SMC-R, both the container
directly using host network and the container using veth network can
successfully match the RDMA device, because the configured pnetid netdev
is a base_ndev. But the container using IPVLAN can not successfully
match the RDMA device and 0x03030000 fallback happens, because the
configured pnetid netdev is not a base_ndev. Additionally, if config
pnetid to the eth1(in host) also can not work for matching RDMA device
when using veth network and doing SMC-R in POD.
To resolve the problems list above, this patch extends to search user
-defined sw pnetid in the clc handshake ndev when no pnetid can be found
in the base_ndev, and the base_ndev take precedence over ndev for backward
compatibility. This patch also can unify the pnetid setup of different
network choices list above in container(Config user-defined sw pnetid in
the netdevice can be seen in POD).
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Reviewed-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent merge between net-next and net, I got some conflicts on
my side because the merge resolution was different from Stephen's one
[1] I applied on my side in the MPTCP tree.
It looks like the code that is now in net-next is using the old way to
retrieve the local and remote addresses. This patch is now using the new
way, like what was in Stephen's email [1].
Also, in get_interface_info(), there were no conflicts in this area,
because that was new code from 'net', but a small adaptation was needed
there as well to get the remote address.
Currently the flexcan driver does only support adding PHYs by using
the "old" regulator bindings. Add support for CAN transceivers as a
PHY. Add the capability to ensure that the PHY is in operational state
when the link is set to an "up" state.
Changes in v4:
- Dropped "if: required: phys" in bindings
- Link to v3: https://lore.kernel.org/r/20250221-flexcan-add-transceiver-caps-v3-0-a947bde55a62@liebherr.com
Changes in v3:
- Have xceiver-supply or phys properties in bindings
- Switch do dev_err_probe in flexcan_probe when checking error of call
devm_phy_optional_get
- Link to v2: https://lore.kernel.org/r/20250220-flexcan-add-transceiver-caps-v2-0-a81970f11846@liebherr.com
Changes in v2:
- Rename variable xceiver to transceiver in struct flexcan_priv and in
flexcan_probe
- Set priv->can.bitrate_max if transceiver is found
- Fix commit messages which claim that transceivers are not supported
- Do not print error on EPROBE_DEFER after calling devm_phy_optional_get in
flexcan_probe
- Link to v1: https://lore.kernel.org/r/20250211-flexcan-add-transceiver-caps-v1-0-c6abb7817b0f@liebherr.com
Dimitri Fedrau [Wed, 12 Mar 2025 17:45:23 +0000 (18:45 +0100)]
can: flexcan: add transceiver capabilities
Currently the flexcan driver does only support adding PHYs by using the
"old" regulator bindings. Add support for CAN transceivers as a PHY. Add
the capability to ensure that the PHY is in operational state when the link
is set to an "up" state.
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py 75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py") de94e8697405 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c a70f891e0fa0 ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()") 1d22d3060b9b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile 6f50175ccad4 ("selftests: Add IPv6 link-local address generation tests for GRE devices.") 2e5584e0f913 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c 661958552eda ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic") fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings")
Linus Torvalds [Thu, 13 Mar 2025 17:58:48 +0000 (07:58 -1000)]
Merge tag 'net-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, bluetooth and wireless.
No known regressions outstanding.
Current release - regressions:
- wifi: nl80211: fix assoc link handling
- eth: lan78xx: sanitize return values of register read/write
functions
Current release - new code bugs:
- ethtool: tsinfo: fix dump command
- bluetooth: btusb: configure altsetting for HCI_USER_CHANNEL
- eth: mlx5: DR, use the right action structs for STEv3
Previous releases - regressions:
- netfilter: nf_tables: make destruction work queue pernet
- gre: fix IPv6 link-local address generation.
- wifi: iwlwifi: fix TSO preparation
- bluetooth: revert "bluetooth: hci_core: fix sleeping function
called from invalid context"
- ovs: revert "openvswitch: switch to per-action label counting in
conntrack"
- eth:
- ice: fix switchdev slow-path in LAG
- bonding: fix incorrect MAC address setting to receive NS
messages
Previous releases - always broken:
- core: prevent TX of unreadable skbs
- sched: prevent creation of classes with TC_H_ROOT
- netfilter: nft_exthdr: fix offset with ipv4_find_option()
- wifi: cfg80211: cancel wiphy_work before freeing wiphy
- mctp: copy headers if cloned
- phy: nxp-c45-tja11xx: add errata for TJA112XA/B
- eth:
- bnxt: fix kernel panic in the bnxt_get_queue_stats{rx | tx}
- mlx5: bridge, fix the crash caused by LAG state check"
* tag 'net-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
net: mana: cleanup mana struct after debugfs_remove()
net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devices
net/mlx5: Bridge, fix the crash caused by LAG state check
net/mlx5: Lag, Check shared fdb before creating MultiPort E-Switch
net/mlx5: Fix incorrect IRQ pool usage when releasing IRQs
net/mlx5: HWS, Rightsize bwc matcher priority
net/mlx5: DR, use the right action structs for STEv3
Revert "openvswitch: switch to per-action label counting in conntrack"
net: openvswitch: remove misbehaving actions length check
selftests: Add IPv6 link-local address generation tests for GRE devices.
gre: Fix IPv6 link-local address generation.
netfilter: nft_exthdr: fix offset with ipv4_find_option()
selftests/tc-testing: Add a test case for DRR class with TC_H_ROOT
net_sched: Prevent creation of classes with TC_H_ROOT
ipvs: prevent integer overflow in do_ip_vs_get_ctl()
selftests: netfilter: skip br_netfilter queue tests if kernel is tainted
netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in insert_tree()
wifi: mac80211: fix MPDU length parsing for EHT 5/6 GHz
qlcnic: fix memory leak issues in qlcnic_sriov_common.c
rtase: Fix improper release of ring list entries in rtase_sw_reset
...
Linus Torvalds [Thu, 13 Mar 2025 17:53:25 +0000 (07:53 -1000)]
Merge tag 'vfs-6.14-rc7.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Bring in an RCU pathwalk fix for afs. This is brought in as a merge
from the vfs-6.15.shared.afs branch that needs this commit and other
trees already depend on it.
- Fix vboxfs unterminated string handling.
* tag 'vfs-6.14-rc7.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs:
vboxsf: Add __nonstring annotations for unterminated strings
afs: Fix afs_atcell_get_link() to handle RCU pathwalk
Paolo Abeni [Thu, 13 Mar 2025 14:04:26 +0000 (15:04 +0100)]
Merge tag 'nf-25-03-13' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Missing initialization of cpu and jiffies32 fields in conncount,
from Kohei Enju.
2) Skip several tests in case kernel is tainted, otherwise tests bogusly
report failure too as they also check for tainted kernel,
from Florian Westphal.
3) Fix a hyphothetical integer overflow in do_ip_vs_get_ctl() leading
to bogus error logs, from Dan Carpenter.
4) Fix incorrect offset in ipv4 option match in nft_exthdr, from
Alexey Kashavkin.
netfilter pull request 25-03-13
* tag 'nf-25-03-13' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_exthdr: fix offset with ipv4_find_option()
ipvs: prevent integer overflow in do_ip_vs_get_ctl()
selftests: netfilter: skip br_netfilter queue tests if kernel is tainted
netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in insert_tree()
====================
Shradha Gupta [Tue, 11 Mar 2025 10:17:40 +0000 (03:17 -0700)]
net: mana: cleanup mana struct after debugfs_remove()
When on a MANA VM hibernation is triggered, as part of hibernate_snapshot(),
mana_gd_suspend() and mana_gd_resume() are called. If during this
mana_gd_resume(), a failure occurs with HWC creation, mana_port_debugfs
pointer does not get reinitialized and ends up pointing to older,
cleaned-up dentry.
Further in the hibernation path, as part of power_down(), mana_gd_shutdown()
is triggered. This call, unaware of the failures in resume, tries to cleanup
the already cleaned up mana_port_debugfs value and hits the following bug:
Carolina Jubran [Mon, 10 Mar 2025 22:01:44 +0000 (00:01 +0200)]
net/mlx5e: Prevent bridge link show failure for non-eswitch-allowed devices
mlx5_eswitch_get_vepa returns -EPERM if the device lacks
eswitch_manager capability, blocking mlx5e_bridge_getlink from
retrieving VEPA mode. Since mlx5e_bridge_getlink implements
ndo_bridge_getlink, returning -EPERM causes bridge link show to fail
instead of skipping devices without this capability.
To avoid this, return -EOPNOTSUPP from mlx5e_bridge_getlink when
mlx5_eswitch_get_vepa fails, ensuring the command continues processing
other devices while ignoring those without the necessary capability.
Fixes: 4b89251de024 ("net/mlx5: Support ndo bridge_setlink and getlink") Signed-off-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/1741644104-97767-7-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jianbo Liu [Mon, 10 Mar 2025 22:01:43 +0000 (00:01 +0200)]
net/mlx5: Bridge, fix the crash caused by LAG state check
When removing LAG device from bridge, NETDEV_CHANGEUPPER event is
triggered. Driver finds the lower devices (PFs) to flush all the
offloaded entries. And mlx5_lag_is_shared_fdb is checked, it returns
false if one of PF is unloaded. In such case,
mlx5_esw_bridge_lag_rep_get() and its caller return NULL, instead of
the alive PF, and the flush is skipped.
Besides, the bridge fdb entry's lastuse is updated in mlx5 bridge
event handler. But this SWITCHDEV_FDB_ADD_TO_BRIDGE event can be
ignored in this case because the upper interface for bond is deleted,
and the entry will never be aged because lastuse is never updated.
To make things worse, as the entry is alive, mlx5 bridge workqueue
keeps sending that event, which is then handled by kernel bridge
notifier. It causes the following crash when accessing the passed bond
netdev which is already destroyed.
To fix this issue, remove such checks. LAG state is already checked in
commit 15f8f168952f ("net/mlx5: Bridge, verify LAG state when adding
bond to bridge"), driver still need to skip offload if LAG becomes
invalid state after initialization.
Shay Drory [Mon, 10 Mar 2025 22:01:41 +0000 (00:01 +0200)]
net/mlx5: Fix incorrect IRQ pool usage when releasing IRQs
mlx5_irq_pool_get() is a getter for completion IRQ pool only.
However, after the cited commit, mlx5_irq_pool_get() is called during
ctrl IRQ release flow to retrieve the pool, resulting in the use of an
incorrect IRQ pool.
Hence, use the newly introduced mlx5_irq_get_pool() getter to retrieve
the correct IRQ pool based on the IRQ itself. While at it, rename
mlx5_irq_pool_get() to mlx5_irq_table_get_comp_irq_pool() which
accurately reflects its purpose and improves code readability.
projects / users / hch / misc.git / log