Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: sirf-dma: remove unused ‘sdesc’
In sirfsoc_dma_pm_suspend(), variable ‘sdesc’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/sirf-dma.c: In function 'sirfsoc_dma_pm_suspend':
drivers/dma/sirf-dma.c:1014:27: warning: variable 'sdesc' set but not used [-Wunused-but-set-variable]
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: s3c24xx: remove unused ‘cdata’
In s3c24xx_dma_get_phy(), variable ‘cdata’ is initialized but never used, which
leads to warning with W=1. Removing this make pdata unused.
drivers/dma/s3c24xx-dma.c: In function ‘s3c24xx_dma_get_phy’:
drivers/dma/s3c24xx-dma.c:293:30: warning: variable ‘cdata’ set but not used [-Wunused-but-set-variable]
struct s3c24xx_dma_channel *cdata;
So remove both of them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: stm32-dma: remove unused ‘src_addr’
In stm32_dma_set_xfer_param(), variable ‘src_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:13: warning: variable ‘src_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: stm32-dma: remove unused ‘dst_addr’
In stm32_dma_set_xfer_param(), variable ‘dst_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:23: warning: variable ‘dst_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: stm32-dma: remove unused ‘sfcr’
In stm32_dma_chan_irq(), variable ‘sfcr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_chan_irq’:
drivers/dma/stm32-dma.c:530:19: warning: variable ‘sfcr’ set but not used [-Wunused-but-set-variable]
u32 status, scr, sfcr;
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: pch_dma: remove unused ‘cookie’
In pd_tx_submit(), variable ‘cookie’ is initialized but never used, which
leads to warning with W=1
drivers/dma/pch_dma.c: In function ‘pd_tx_submit’:
drivers/dma/pch_dma.c:420:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
dma_cookie_t cookie;
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: mic_x100_dma: remove unused ‘data’
In mic_dma_init(), variable ‘data’ is initialized but never used, which
leads to warning with W=1
drivers/dma/mic_x100_dma.c: In function ‘mic_dma_init’:
drivers/dma/mic_x100_dma.c:557:17: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
unsigned long data;
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: img-mdc: remove unused ‘prev_phys’
In mdc_prep_dma_memcpy(), mdc_prep_dma_cyclic() and mdc_prep_slave_sg()
variable ‘prev_phys’ is initialized but never used, which
leads to warning with W=1
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_memcpy’:
drivers/dma/img-mdc-dma.c:295:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_cyclic’:
drivers/dma/img-mdc-dma.c:378:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_slave_sg’:
drivers/dma/img-mdc-dma.c:461:24: warning: variable ‘prev_phys’ set but not
used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: usb-dmac: remove unused ‘uchan’
In usb_dmac_of_xlate(), variable ‘uchan’ is initialized but never used, which
leads to warning with W=1
drivers/dma/sh/usb-dmac.c: In function ‘usb_dmac_of_xlate’:
drivers/dma/sh/usb-dmac.c:655:24: warning: variable ‘uchan’ set but not used [-Wunused-but-set-variable]
struct usb_dmac_chan *uchan;
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: ioat: remove unused ‘res’
In __cleanup(), variable ‘res’ is initialized but never used, which
leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘__cleanup’:
drivers/dma/ioat/dma.c:614:28: warning: variable ‘res’ set but not used [-Wunused-but-set-variable]
struct dmaengine_result res;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: ioat: remove unused ‘ioat_dma’
In ioat_tx_submit_unlock(), variable ‘ioat_dma’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘ioat_alloc_ring_ent’:
drivers/dma/ioat/dma.c:341:25: warning: variable ‘ioat_dma’ set but not used [-Wunused-but-set-variable]
struct ioatdma_device *ioat_dma;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul [Fri, 9 Dec 2016 09:54:12 +0000 (15:24 +0530)]
dmaengine: ioat: remove unused ‘is_raid_device’
In ioat3_dma_probe(), variable ‘is_raid_device’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/init.c: In function ‘ioat3_dma_probe’:
drivers/dma/ioat/init.c:1084:7: warning: variable ‘is_raid_device’ set
but not used [-Wunused-but-set-variable]
bool is_raid_device = false;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Alexandre Belloni [Thu, 1 Dec 2016 10:49:03 +0000 (11:49 +0100)]
dmaengine: at_xdmac: don't restore unsaved status
save_gs is supposed to save the channel status in order to be restored at
resume time but it is never updated and is always 0. Anyway, the channel
status is updated in the per channel loop later in the resume function.
Pan Bian [Fri, 2 Dec 2016 14:50:38 +0000 (22:50 +0800)]
dmaengine: ioat: set error code on failures
In function ioat_xor_val_self_test(), when the calls to
dma_mapping_error() fail, the value of return variable err is 0
(indicates no error). As a result, the return value may be inconsistent
with the execution status. This patch fixes the bug by assigning
"-ENOMEM" to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188601 Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pan Bian [Fri, 2 Dec 2016 14:49:01 +0000 (22:49 +0800)]
dmaengine: ioat: set error code on failures
In function ioat_dma_self_test(), when the calls to dma_mapping_error()
fails, the value of return variable err is 0 (indicates no error). As a
result, the return value may be inconsistent with the execution status.
This patch fixes the bug by assigning -ENOMEM to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188591 Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Eugeniy Paltsev [Fri, 25 Nov 2016 14:59:07 +0000 (17:59 +0300)]
dmaengine: DW DMAC: add multi-block property to device tree
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Vignesh R [Wed, 23 Nov 2016 09:27:55 +0000 (14:57 +0530)]
dmaengine: edma: re-initialize dummy slot during system resume
The last param set in a transfer should always be pointing to dummy
param set in non-cyclic mode. When system wakes from low power state
EDMA PARAM slots may be reset to random values. Hence, re-initialize
dummy slot to dummy param set on system resume.
Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi [Tue, 29 Nov 2016 14:23:42 +0000 (16:23 +0200)]
dmaengine: omap-dma: Support for slave devices with data port window
Based on the src/dst_port_window_size - if it is set - configure the DMA
channel to use double indexing in order to be able to loop within the
address window.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi [Tue, 29 Nov 2016 14:23:41 +0000 (16:23 +0200)]
dmaengine: dma_slave_config: add support for slave port window
Some slave devices uses address window instead of single register for read
and/or write of data. With the src/dst_port_window_size the address window
can be specified and the DMAengine driver should use this information to
correctly set up the transfer to loop within the provided window.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dave Jiang [Tue, 29 Nov 2016 20:22:20 +0000 (13:22 -0700)]
dmaengine: dmatest: honor alignment restriction for buffers
Existing implementation does not honor the alignment restrictions imposed
by the DMA engines. Allocate buffers with built in slack for honoring
alignment restrictions. Creating new arrays to hold the aligned pointers
and use those pointers for operations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Hao Zhang [Sat, 19 Nov 2016 16:43:56 +0000 (00:43 +0800)]
dmaengine: sun6i: fix the uninitialized value for v_lli
dma_pool_alloc does not initialize the value of the newly allocated
block for the v_lli, and the uninitilize value make the tests failed
which is on pine64 with dmatest.
we can fix it just change the "|=" to "=" for the v_lli->cfg.
Nandor Han [Tue, 11 Oct 2016 11:13:41 +0000 (14:13 +0300)]
dmaengine: imx-sdma - correct the dma transfer residue calculation
The residue calculation was taking in consideration that dma
transaction status will be always retrieved in the dma callback
used to inform that dma transfer is complete. However this is not
the case for all subsystems that use dma. Some subsystems use a
timer to check the dma status periodically.
Therefore the calculation was updated and residue is calculated
accordingly by a) update the residue calculation taking in
consideration the last used buffer index by using *buf_ptail* variable
and b) chn_real_count (number of bytes transferred) is initialized to
zero, when dma channel is created, to avoid using an uninitialized
value in residue calculation when dma status is checked without
waiting dma complete event.
Signed-off-by: Nandor Han <nandor.han@ge.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sinan Kaya [Sat, 19 Nov 2016 19:28:37 +0000 (14:28 -0500)]
dmaengine: qcom_hidma: autoload while probing ACPI
MODULE_DEVICE_TABLE is used by the kernel to determine which device driver
should be loaded for which platform device. MODULE_DEVICE_TABLE has been
only defined for the device-tree based platforms in the current code.
Defining it also for ACPI based platforms.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sylwester Nawrocki [Thu, 10 Nov 2016 15:17:51 +0000 (16:17 +0100)]
spi: s3c64xx: Do not use platform_data for DMA parameters
All related platforms use either devicetree or the DMA slave
map API for mapping DMA channels to DMA slaves so we can now
stop using platform_data for passing DMA details.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Tested-by: Andi Shyti <andi.shyti@samsung.com> Tested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sylwester Nawrocki [Thu, 10 Nov 2016 15:17:50 +0000 (16:17 +0100)]
ARM: s3c64xx: Add DMA slave maps for PL080 devices
This patch adds DMA slave map tables to the pl080 devices's
platform_data in order to support the new channel request API.
A few devices for which there was no DMA support with current
code are omitted in the tables.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Tested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sylwester Nawrocki [Thu, 10 Nov 2016 15:17:49 +0000 (16:17 +0100)]
dmaengine: pl08x: Add support for the DMA slave map
This patch adds support for the new channel request API introduced
in commit a8135d0d79e9d0ad3a4ff494fceeaae83
"dmaengine: core: Introduce new, universal API to request a channel".
param field of struct dma_slave_map type entries in the platform
data structure should be pointing to struct pl08x_channel_data
of related DMA channel.
Vinod Koul [Thu, 17 Nov 2016 09:53:01 +0000 (15:23 +0530)]
dmaengine: st_fdma: Revert: "Revert: Update st_fdma to 'depends on REMOTEPROC'"
This reverts commit 6d066389d598b3c3818c3c841179c2f95bbfe702 "(dmaengine:
st_fdma: Revert: Update st_fdma to 'depends on REMOTEPROC')" as the commit
it reverted was fine.
Sinan Kaya [Mon, 14 Nov 2016 19:34:53 +0000 (14:34 -0500)]
dmaengine: qcom_hidma: cleanup sysfs entries during remove
The 4.8-rc8 kernel is printing duplicate file entry warnings while removing
the HIDMA object. This is caused by stale sysfs entries remaining from the
previous execution.
Create hidma_sysfs_init and hidma_sysfs_uninit functions and call them from
the probe and remove path. To do proper clean up, adding the attrs object
to the device data structure to keep it around until remove call is made.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Stephen Barber [Tue, 1 Nov 2016 23:44:27 +0000 (16:44 -0700)]
dmaengine: pl330: Handle xferred count if DMAMOV hasn't finished
After executing DMAGO it's possible that a request can come in for the
current xferred count, but if that happens too soon then DMAMOV SAR/DAR
may not have yet completed. If that happens, we should explicitly return 0
since nothing has been transferred yet.
Signed-off-by: Stephen Barber <smbarber@chromium.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Niklas Cassel [Mon, 24 Oct 2016 13:29:15 +0000 (15:29 +0200)]
dmaengine: nbpfaxi: add optional max-burst property for memory reads/writes
Due to a hardware bug, reading memory (from the Accelerator Coherency Port)
with a burst size equal to the maximum burst size allowed by the DMA
hardware's buffer size will cause a hardware hang on the ARTPEC-6 SoC,
where the only solution is a manual power cycle.
On ARTPEC-6, this hardware bug does not trigger when writing memory (to the
Accelerator Coherency Port) with a burst size equal to the maximum burst
size allowed by the DMA hardware's buffer size.
To avoid this hardware hang, introduce a new optional max-burst property
for memory reads. For completeness, also introduce a max-burst property for
memory writes.
Paul Gortmaker [Sat, 22 Oct 2016 22:25:10 +0000 (18:25 -0400)]
dmaengine: tegra210-adma: convert TEGRA210_ADMA from bool to tristate
This driver currently uses modular infrastructure but is controlled
by a bool Kconfig.
There is a general consensus from the DMA reviewers and maintainers
that "if it can be modular, it should be modular" in order to keep
the bzImage size under control for multi platform kernels.
Build tested only. Also needed some new pm_clk symbols exported
before this commit is applied to tree in order to avoid modpost
errors like:
Javier Martinez Canillas [Wed, 19 Oct 2016 20:32:33 +0000 (17:32 -0300)]
dmaengine: fsl_raid: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/dma/fsl_raid.ko | grep alias
$
After this patch:
$ modinfo drivers/dma/fsl_raid.ko | grep alias
alias: of:N*T*Cfsl,raideng-v1.0C*
alias: of:N*T*Cfsl,raideng-v1.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sinan Kaya [Fri, 21 Oct 2016 16:37:59 +0000 (12:37 -0400)]
dmaengine: qcom_hidma: add MSI support for interrupts
The interrupts can now be delivered as platform MSI interrupts on newer
platforms. The code looks for a new OF and ACPI strings in order to enable
the functionality.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sinan Kaya [Fri, 21 Oct 2016 16:37:58 +0000 (12:37 -0400)]
dmaengine: qcom_hidma: protect common data structures
When MSI interrupts are supported, error and the transfer interrupt can
come from multiple processor contexts.
Each error interrupt is an MSI interrupt. If the channel is disabled by
the first error interrupt, the remaining error interrupts will gracefully
return in the interrupt handler.
If an error is observed while servicing the completions in success case,
the posting of the completions will be aborted as soon as channel disabled
state is observed. The error interrupt handler will take it from there and
finish the remaining completions. We don't want to create multiple success
and error messages to be delivered to the client in mixed order.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sinan Kaya [Fri, 21 Oct 2016 16:37:56 +0000 (12:37 -0400)]
dmaengine: qcom_hidma: make pending_tre_count atomic
Getting ready for the MSI interrupts. The pending_tre_count is used
in the interrupt handler to make sure all outstanding requests are
serviced.
The driver will allocate 11 MSI interrupts. Each MSI interrupt can be
assigned to a different CPU. Then, we have a race condition for common
variables as they share the same interrupt handler with a different
cause bit and they can potentially be executed in parallel. Making this
variable atomic so that it can be updated from multiple processor
contexts.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Griffin [Fri, 21 Oct 2016 08:44:25 +0000 (09:44 +0100)]
dmaengine: st_fdma: Update st_fdma to 'depends on REMOTEPROC'.
During randconfig builds you can get the following warning
"warning: (ST_FDMA) selects ST_SLIM_REMOTEPROC which has unmet direct
dependencies (REMOTEPROC)"
randconfig builds should always build without any warnings so
update fdma to depend on REMOTEPROC so this can not happen.
Wei Yongjun [Wed, 19 Oct 2016 13:23:50 +0000 (13:23 +0000)]
dmaengine: st_fdma: Fix the error return code in st_fdma_probe()
In case of error, the function st_slim_rproc_alloc() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Colin Ian King [Sun, 16 Oct 2016 12:25:47 +0000 (13:25 +0100)]
dmaengine: ioatdma: loop for number elements in array chanerr_str
Just iterate over the number of elements in array chanerr_str rather
than for all 32 bits. This removes the need for a NULL chanerr_str[i]
check which could possibly overrun if the upper bits (28..31) of
chanerr are set and 27th bit in chanerr is zero. This simplifies the
code by removing an if statement and a break.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sinan Kaya [Fri, 7 Oct 2016 05:25:14 +0000 (01:25 -0400)]
dmaengine: qcom_hidma: break completion processing on error
We try to consume as much successful transfers as possible. Now that we
support MSI interrupts, an error interrupt might be observed by another
processor while we are finishing the successful ones.
Try to abort successful processing if this is the case.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since 'commit acc29fb8f792 ("debugfs: ->d_parent is never NULL or
negative")', HIDMA object removal is no longer working. This is due to
redundant debugfs remove call in hidma_debug_uninit.
The newly added st_fdma driver introduces a build warning for
allmodconfig when we add '-Wmaybe-uninitialized':
drivers/dma/st_fdma.c: In function 'st_fdma_probe':
drivers/dma/st_fdma.c:777:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The warning is correct, though this can't happen in practice
as the check is redundant (we don't get to this function if
the pointer is NULL). Even if the function were called with a
NULL of_node, the check is not needed because of_property_read_u32
can deal with a NULL argument by returning an error.
Removing the unnecessary code simplifies the function and avoids
the condition that we get the warning for.
Sinan Kaya [Thu, 6 Oct 2016 19:33:14 +0000 (15:33 -0400)]
dmaengine: qcom_hidma: prevent disable in error
When an error is observed, we try to disable the channel and prevent
further accesses from the client.
Depending on the type of error, transitioning into disabled state might
not be possible. Adding a check to make sure that HW is in enabled/running
state before the disable transition happens.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sebastian Andrzej Siewior [Fri, 14 Oct 2016 05:00:47 +0000 (10:30 +0530)]
dmaengine: omap-dma: add support for pause of non-cyclic transfers
This DMA driver is used by 8250-omap on DRA7-evm. There is one
requirement that is to pause a transfer. This is currently used on the RX
side. It is possible that the UART HW aborted the RX (UART's RX-timeout)
but the DMA controller starts the transfer shortly after.
Before we can manually purge the FIFO we need to pause the transfer,
check how many bytes it already received and terminate the transfer
without it making any progress.
From testing on the TX side it seems that it is possible that we invoke
pause once the transfer has completed which is indicated by the missing
CCR_ENABLE bit but before the interrupt has been noticed. In that case the
interrupt will come even after disabling it.
The AM572x manual says that we have to wait for the CCR_RD_ACTIVE &
CCR_WR_ACTIVE bits to be gone before programming it again here is the
drain loop. Also it looks like without the drain the TX-transfer makes
sometimes progress.
One note: The pause + resume combo is broken because after resume the
the complete transfer will be programmed again. That means the already
transferred bytes (until the pause event) will be sent again. This is
currently not important for my UART user because it does only pause +
terminate.
v3…v4:
- update subject line.
v2…v3:
- rephrase the comment based on Russell's information / feedback.
v1…v2:
- move the drain loop into omap_dma_drain_chan() instead of having it
twice.
- allow pause only for DMA_DEV_TO_MEM transfers if non-cyclic. Add a
comment why DMA_MEM_TO_DEV not allowed.
- clear pause on terminate_all. Otherwise pause() + terminate_all()
will keep the pause bit set and we can't pause the following
transfer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[vigneshr@ti.com: drain channel only when buffering is on, rebase to v4.8] Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Griffin [Tue, 18 Oct 2016 09:39:11 +0000 (10:39 +0100)]
dmaengine: st_fdma: Add STMicroelectronics FDMA engine driver support
This patch adds support for the Flexible Direct Memory Access (FDMA) core
driver. The FDMA is a slim core CPU with a dedicated firmware.
It is a general purpose DMA controller capable of supporting 16
independent DMA channels. Data moves maybe from memory to memory
or between memory and paced latency critical real time targets and it
is found on al STi based chipsets.
Peter Griffin [Tue, 18 Oct 2016 09:39:08 +0000 (10:39 +0100)]
remoteproc: Update Kconfig setup to 'depends on REMOTEPROC'
Make REMOTEPROC core a selectable kconfig option, and update
remoteproc client drivers to 'depends on' the core. This avoids
some nasty Kconfig recursive dependency issues. Also when using
menuconfig client drivers will be hidden until the core has been
enabled.
Documentation/kbuild/kconfig-language.txt:
Note:
select should be used with care. select will force
a symbol to a value without visiting the dependencies.
By abusing select you are able to select a symbol FOO even
if FOO depends on BAR that is not set.
In general use select only for non-visible symbols
(no prompts anywhere) and for symbols with no dependencies.
That will limit the usefulness but on the other hand avoid
the illegal configurations all over.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Griffin [Tue, 18 Oct 2016 09:39:06 +0000 (10:39 +0100)]
remoteproc: st_slim_rproc: add a slimcore rproc driver
slim core is used as a basis for many IPs in the STi
chipsets such as fdma and demux. To avoid duplicating
the elf loading code in each device driver a slim
rproc driver has been created.
This driver is designed to be used by other device drivers
such as fdma, or demux whose IP is based around a slim core.
The device driver can call slim_rproc_alloc() to allocate
a slim rproc and slim_rproc_put() when finished.
This driver takes care of ioremapping the slim
registers (dmem, imem, slimcore, peripherals), whose offsets
and sizes can change between IP's. It also obtains and enables
any clocks used by the device. This approach avoids having
a double mapping of the registers as slim_rproc does not register
its own platform device. It also maps well to device tree
abstraction as it allows us to have one dt node for the whole
device.
All of the generic rproc elf loading code can be reused, and
we provide start() stop() hooks to start and stop the slim
core once the firmware has been loaded. This has been tested
successfully with fdma driver.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds [Sat, 15 Oct 2016 19:09:13 +0000 (12:09 -0700)]
Merge tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs
Pull befs fixes from Luis de Bethencourt:
"I recently took maintainership of the befs file system [0]. This is
the first time I send you a git pull request, so please let me know if
all the below is OK.
Salah Triki and myself have been cleaning the code and fixing a few
small bugs.
Sorry I couldn't send this sooner in the merge window, I was waiting
to have my GPG key signed by kernel members at ELCE in Berlin a few
days ago."
[0] https://lkml.org/lkml/2016/7/27/502
* tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs: (39 commits)
befs: befs: fix style issues in datastream.c
befs: improve documentation in datastream.c
befs: fix typos in datastream.c
befs: fix typos in btree.c
befs: fix style issues in super.c
befs: fix comment style
befs: add check for ag_shift in superblock
befs: dump inode_size superblock information
befs: remove unnecessary initialization
befs: fix typo in befs_sb_info
befs: add flags field to validate superblock state
befs: fix typo in befs_find_key
befs: remove unused BEFS_BT_PARMATCH
fs: befs: remove ret variable
fs: befs: remove in vain variable assignment
fs: befs: remove unnecessary *befs_sb variable
fs: befs: remove useless initialization to zero
fs: befs: remove in vain variable assignment
fs: befs: Insert NULL inode to dentry
fs: befs: Remove useless calls to brelse in befs_find_brun_dblindirect
...
Linus Torvalds [Sat, 15 Oct 2016 17:03:15 +0000 (10:03 -0700)]
Merge tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot
time as possible, hoping to capitalize on any possible variation in
CPU operation (due to runtime data differences, hardware differences,
SMP ordering, thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example
for how to manipulate kernel code using the gcc plugin internals"
* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Mark functions with __latent_entropy
gcc-plugins: Add latent_entropy plugin
Linus Torvalds [Sat, 15 Oct 2016 16:26:12 +0000 (09:26 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Linus Torvalds [Sat, 15 Oct 2016 16:20:54 +0000 (09:20 -0700)]
Merge tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few trivial small fixes"
* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: line6: fix a crash in line6_hwdep_write()
ALSA: seq: fix passing wrong pointer in function call of compatibility layer
ALSA: hda - Fix a failure of micmute led when having multi adcs
ALSA: line6: Fix POD X3 Live audio input
Linus Torvalds [Sat, 15 Oct 2016 01:19:05 +0000 (18:19 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more misc uaccess and vfs updates from Al Viro:
"The rest of the stuff from -next (more uaccess work) + assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
score: traps: Add missing include file to fix build error
fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
fs/super.c: fix race between freeze_super() and thaw_super()
overlayfs: Fix setting IOP_XATTR flag
iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
blackfin: no access_ok() for __copy_{to,from}_user()
arm64: don't zero in __copy_from_user{,_inatomic}
arm: don't zero in __copy_from_user_inatomic()/__copy_from_user()
arc: don't leak bits of kernel stack into coredump
alpha: get rid of tail-zeroing in __copy_user()
Linus Torvalds [Sat, 15 Oct 2016 00:47:31 +0000 (17:47 -0700)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Including:
- nine bug fixes for stable. Some of these we found at the recent two
weeks of SMB3 test events/plugfests.
- significant improvements in reconnection (e.g. if server or network
crashes) especially when mounted with "persistenthandles" or to
server which advertises Continuous Availability on the share.
- a new mount option "idsfromsid" which improves POSIX compatibility
in some cases (when winbind not configured e.g.) by better (and
faster) fetching uid/gid from acl (when "cifsacl" mount option is
enabled). NB: we are almost complete work on "cifsacl" (querying
mode/uid/gid from ACL) for SMB3, but SMB3 support for cifsacl is
not included in this set.
- improved handling for SMB3 "credits" (even if server is buggy)
Still working on two sets of changes:
- cifsacl enablement for SMB3
- cleanup of RFC1001 length calculation (so we can handle encryption
and multichannel and RDMA)
And a couple of new bugs were reported recently (unrelated to above)
so will probably have another merge request next week"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
CIFS: Retrieve uid and gid from special sid if enabled
CIFS: Add new mount option to set owner uid and gid from special sids in acl
CIFS: Reset read oplock to NONE if we have mandatory locks after reopen
CIFS: Fix persistent handles re-opening on reconnect
SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup
SMB2: Separate Kerberos authentication from SMB2_sess_setup
Expose cifs module parameters in sysfs
Cleanup missing frees on some ioctls
Enable previous version support
Do not send SMB3 SET_INFO request if nothing is changing
SMB3: Add mount parameter to allow user to override max credits
fs/cifs: reopen persistent handles on reconnect
Clarify locking of cifs file and tcon structures and make more granular
Fix regression which breaks DFS mounting
fs/cifs: keep guid when assigning fid to fileinfo
SMB3: GUIDs should be constructed as random but valid uuids
Set previous session id correctly on SMB3 reconnect
cifs: Limit the overall credit acquired
Display number of credits available
Add way to query creation time of file via cifs xattr
...
Linus Torvalds [Sat, 15 Oct 2016 00:44:56 +0000 (17:44 -0700)]
Merge branch 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Some fixes from Omar and Dave Sterba for our new free space tree.
This isn't heavily used yet, but as we move toward making it the new
default we wanted to nail down an endian bug"
* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: tests: uninline member definitions in free_space_extent
btrfs: tests: constify free space extent specs
Btrfs: expand free space tree sanity tests to catch endianness bug
Btrfs: fix extent buffer bitmap tests on big-endian systems
Btrfs: catch invalid free space trees
Btrfs: fix mount -o clear_cache,space_cache=v2
Btrfs: fix free space tree bitmaps on big-endian systems
projects / users / jedix / linux-maple.git / log