Commit cbffaf7aa09e ("can: flexcan: Always use last mailbox for TX")
introduced a loop letting i run up to (including) ARRAY_SIZE(regs->mb)
and in the body accessed regs->mb[i] which is an out-of-bounds array
access that then resulted in an access to an reserved register area.
Later this was changed by commit 0517961ccdf1 ("can: flexcan: Add
provision for variable payload size") to iterate a bit differently but
still runs one iteration too much resulting to call
flexcan_get_mb(priv, priv->mb_count)
which results in a WARN_ON and then a NULL pointer exception. This
only affects devices compatible with "fsl,p1010-flexcan",
"fsl,imx53-flexcan", "fsl,imx35-flexcan", "fsl,imx25-flexcan",
"fsl,imx28-flexcan", so newer i.MX SoCs are not affected.
Fixes: cbffaf7aa09e ("can: flexcan: Always use last mailbox for TX") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: linux-stable <stable@vger.kernel.org> # >= 4.20 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup()
when the conversion into ktime multiplies the given value with NSEC_PER_USEC
(1000).
Add a check for the given tv_usec, so that the value stays below one second.
Additionally limit the tv_sec value to a reasonable value for CAN related
use-cases of 400 days and ensure all values to be positive.
Reported-by: Kyungtae Kim <kt0755@gmail.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26 Tested-by: Kyungtae Kim <kt0755@gmail.com> Acked-by: Andre Naujoks <nautsch2@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch revert commit 7da11ba5c506
("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
After introduction of this change we encountered following new error
message on various i.MX plattforms (flexcan):
| flexcan 53fc8000.can can0: __can_get_echo_skb: BUG! Trying to echo non
| existing skb: can_priv::echo_skb[0]
The introduction of the message was a mistake because
priv->echo_skb[idx] = NULL is a perfectly valid in following case: If
CAN_RAW_LOOPBACK is disabled (setsockopt) in applications, the pkt_type
of the tx skb's given to can_put_echo_skb is set to PACKET_LOOPBACK. In
this case can_put_echo_skb will not set priv->echo_skb[idx]. It is
therefore kept NULL.
As additional argument for revert: The order of check and usage of idx
was changed. idx is used to access an array element before checking it's
boundaries.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com> Fixes: 7da11ba5c506 ("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The way we allocate events works fine in most cases, except
when multiple PCI devices share an ITS-visible DevID, and that
one of them is trying to use MultiMSI allocation.
In that case, our allocation is not guaranteed to be zero-based
anymore, and we have to make sure we allocate it on a boundary
that is compatible with the PCI Multi-MSI constraints.
Fix this by allocating the full region upfront instead of iterating
over the number of MSIs. MSI-X are always allocated one by one,
so this shouldn't change anything on that front.
The recent addition of SPDX license identifiers to the files in
drivers/net/ethernet/sun created a licensing conflict.
The cassini driver files contain a proper license notice:
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
but the SPDX change added:
SPDX-License-Identifier: GPL-2.0
So the file got tagged GPL v2 only while in fact it is licensed under GPL
v2 or later.
It's nice that people care about the SPDX tags, but they need to be more
careful about it. Not everything under (the) sun belongs to ...
Fix up the SPDX identifier and remove the boiler plate text as it is
redundant.
Fixes: c861ef83d771 ("sun: Add SPDX license tags to Sun network drivers") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Shannon Nelson <shannon.nelson@oracle.com> Cc: Zhu Yanjun <yanjun.zhu@oracle.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com> Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent commit which prevented a division by 0 issue in the alarm timer
code broke posix CPU timers as an unwanted side effect.
The reason is that the common rearm code checks for timer->it_interval
being 0 now. What went unnoticed is that the posix cpu timer setup does not
initialize timer->it_interval as it stores the interval in CPU timer
specific storage. The reason for the separate storage is historical as the
posix CPU timers always had a 64bit nanoseconds representation internally
while timer->it_interval is type ktime_t which used to be a modified
timespec representation on 32bit machines.
Instead of reverting the offending commit and fixing the alarmtimer issue
in the alarmtimer code, store the interval in timer->it_interval at CPU
timer setup time so the common code check works. This also repairs the
existing inconistency of the posix CPU timer code which kept a single shot
timer armed despite of the interval being 0.
The separate storage can be removed in mainline, but that needs to be a
separate commit as the current one has to be backported to stable kernels.
Fixes: 0e334db6bb4b ("posix-timers: Fix division by zero bug") Reported-by: H.J. Lu <hjl.tools@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190111133500.840117406@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in the native case entry into the kernel happens on the trampoline
stack, PV Xen kernels get entered with the current thread stack right
away. Hence source and destination stacks are identical in that case,
and special care is needed.
Other than in sync_regs() the copying done on the INT80 path isn't
NMI / #MC safe, as either of these events occurring in the middle of the
stack copying would clobber data on the (source) stack.
There is similar code in interrupt_entry() and nmi(), but there is no fixup
required because those code paths are unreachable in XEN PV guests.
[ tglx: Sanitized subject, changelog, Fixes tag and stable mail address. Sigh ]
Fixes: 7f2590a110b8 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries") Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Juergen Gross <jgross@suse.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Peter Anvin <hpa@zytor.com> Cc: xen-devel@lists.xenproject.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/5C3E1128020000780020DFAD@prv1-mh.provo.novell.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a bug where the per-mm pkey state was not being preserved across
fork() in the child. fork() is performed in the pkey selftests, but all of
the pkey activity is performed in the parent. The child does not perform
any actions sensitive to pkey state.
To make the test more sensitive to these kinds of bugs, add a fork() where
the parent exits, and execution continues in the child.
To achieve this let the key exhaustion test not terminate at the first
allocation failure and fork after 2*NR_PKEYS loops and continue in the
child.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: bp@alien8.de Cc: hpa@zytor.com Cc: peterz@infradead.org Cc: mpe@ellerman.id.au Cc: will.deacon@arm.com Cc: luto@kernel.org Cc: jroedel@suse.de Cc: stable@vger.kernel.org Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Will Deacon <will.deacon@arm.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Joerg Roedel <jroedel@suse.de> Link: https://lkml.kernel.org/r/20190102215657.585704B7@viggo.jf.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory protection key behavior should be the same in a child as it was
in the parent before a fork. But, there is a bug that resets the
state in the child at fork instead of preserving it.
The creation of new mm's is a bit convoluted. At fork(), the code
does:
1. memcpy() the parent mm to initialize child
2. mm_init() to initalize some select stuff stuff
3. dup_mmap() to create true copies that memcpy() did not do right
For pkeys two bits of state need to be preserved across a fork:
'execute_only_pkey' and 'pkey_allocation_map'.
Those are preserved by the memcpy(), but mm_init() invokes
init_new_context() which overwrites 'execute_only_pkey' and
'pkey_allocation_map' with "new" values.
The author of the code erroneously believed that init_new_context is *only*
called at execve()-time. But, alas, init_new_context() is used at execve()
and fork().
The result is that, after a fork(), the child's pkey state ends up looking
like it does after an execve(), which is totally wrong. pkeys that are
already allocated can be allocated again, for instance.
To fix this, add code called by dup_mmap() to copy the pkey state from
parent to child explicitly. Also add a comment above init_new_context() to
make it more clear to the next poor sod what this code is used for.
Fixes: e8c24d3a23a ("x86/pkeys: Allocation/free syscalls") Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: bp@alien8.de Cc: hpa@zytor.com Cc: peterz@infradead.org Cc: mpe@ellerman.id.au Cc: will.deacon@arm.com Cc: luto@kernel.org Cc: jroedel@suse.de Cc: stable@vger.kernel.org Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Will Deacon <will.deacon@arm.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Joerg Roedel <jroedel@suse.de> Link: https://lkml.kernel.org/r/20190102215655.7A69518C@viggo.jf.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes the allocation of cached_vmcs12 to use kzalloc instead of
kmalloc. This removes the information leak found by Syzkaller (see
Reported-by) in this case and prevents similar leaks from happening
based on cached_vmcs12.
It also changes vmx_get_nested_state to copy out the full 4k VMCS12_SIZE
in copy_to_user rather than only the size of the struct.
Tested: rebuilt against head, booted, and ran the syszkaller repro
https://syzkaller.appspot.com/text?tag=ReproC&x=174efca3400000 without
observing any problems.
Reported-by: syzbot+ded1696f6b50b615b630@syzkaller.appspotmail.com Fixes: 8fcc4b5923af5de58b80b53a069453b135693304 Cc: stable@vger.kernel.org Signed-off-by: Tom Roeder <tmroeder@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM hypercalls return a negative value error code in case of a fatal
error, e.g. when the hypercall isn't supported or was made with invalid
parameters. WARN_ONCE on fatal errors when sending PV IPIs as any such
error all but guarantees an SMP system will hang due to a missing IPI.
Fixes: aaffcfd1e82d ("KVM: X86: Implement PV IPIs in linux guest") Cc: stable@vger.kernel.org Cc: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recognition of the KVM_HC_SEND_IPI hypercall was unintentionally
wrapped in "#ifdef CONFIG_X86_64", causing 32-bit KVM hosts to reject
any and all PV IPI requests despite advertising the feature. This
results in all KVM paravirtualized guests hanging during SMP boot due
to IPIs never being delivered.
Fixes: 4180bf1b655a ("KVM: X86: Implement "send IPI" hypercall") Cc: stable@vger.kernel.org Cc: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The single-step debugging of KVM guests on x86 is broken: if we run
gdb 'stepi' command at the breakpoint when the guest interrupts are
enabled, RIP always jumps to native_apic_mem_write(). Then other
nasty effects follow.
Long investigation showed that on Jun 7, 2017 the
commit c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
introduced the kvm_run.debug corruption: kvm_vcpu_do_singlestep() can
be called without X86_EFLAGS_TF set.
Let's fix it. Please consider that for -stable.
Signed-off-by: Alexander Popov <alex.popov@linux.com> Cc: stable@vger.kernel.org Fixes: c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall") Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dm-crypt cipher specification in a mapping table is defined as:
cipher[:keycount]-chainmode-ivmode[:ivopts]
or (new crypt API format):
capi:cipher_api_spec-ivmode[:ivopts]
For ESSIV, the parameter includes hash specification, for example:
aes-cbc-essiv:sha256
The implementation expected that additional IV option to never include
another dash '-' character.
But, with SHA3, there are names like sha3-256; so the mapping table
parser fails:
Commit 00a0ea33b495 ("dm thin: do not queue freed thin mapping for next
stage processing") changed process_prepared_discard_passdown_pt1() to
increment all the blocks being discarded until after the passdown had
completed to avoid them being prematurely reused.
IO issued to a thin device that breaks sharing with a snapshot, followed
by a discard issued to snapshot(s) that previously shared the block(s),
results in passdown_double_checking_shared_status() being called to
iterate through the blocks double checking their reference count is zero
and issuing the passdown if so. So a side effect of commit 00a0ea33b495
is passdown_double_checking_shared_status() was broken.
Fix this by checking if the block reference count is greater than 1.
Also, rename dm_pool_block_is_used() to dm_pool_block_is_shared().
Fixes: 00a0ea33b495 ("dm thin: do not queue freed thin mapping for next stage processing") Cc: stable@vger.kernel.org # 4.9+ Reported-by: ryan.p.norwood@gmail.com Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memcpy_fromio() doesn't provide any control over access size. For example,
on arm64, it is implemented using readb and readq. This may trigger a
synchronous external abort:
Assuming aligned 32-bit registers, let's use readl, after making sure
that 'offset' and 'len' are indeed multiples of 4.
Fixes: ba80917d9932d ("scsi: ufs: ufshcd_dump_regs to use memcpy_fromio") Cc: <stable@vger.kernel.org> Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Tested-by: Evan Green <evgreen@chromium.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The _DSM function number validation only happens to succeed when the
generic Linux command number translation corresponds with a
DSM-family-specific function number. This breaks NVDIMM-N
implementations that correctly implement _LSR, _LSW, and _LSI, but do
not happen to publish support for DSM function numbers 4, 5, and 6.
Recall that the support for _LS{I,R,W} family of methods results in the
DIMM being marked as supporting those command numbers at
acpi_nfit_register_dimms() time. The DSM function mask is only used for
ND_CMD_CALL support of non-NVDIMM_FAMILY_INTEL devices.
In preparation for using function number 0 as an error value, prevent it
from being considered a valid function value by acpi_nfit_ctl().
Cc: <stable@vger.kernel.org> Cc: stuart hayes <stuart.w.hayes@gmail.com> Fixes: e02fb7264d8a ("nfit: add Microsoft NVDIMM DSM command set...") Reported-by: Jeff Moyer <jmoyer@redhat.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An integer overflow may arise in uinput_validate_absinfo() if "max - min"
can't be represented by an "int". We should check for overflow before
trying to use the result.
Reported-by: Kyungtae Kim <kt0755@gmail.com> Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usec part of the timeval is defined as
__kernel_suseconds_t tv_usec; /* microseconds */
Arnd noticed that sparc64 is the only architecture that defines
__kernel_suseconds_t as int rather than long.
This breaks the current y2038 fix for kernel as we only access and define
the timeval struct for non-kernel use cases. But, this was hidden by an
another typo in the use of __KERNEL__ qualifier.
Fix the typo, and provide an override for sparc64.
Fixes: 152194fe9c3f ("Input: extend usable life of event timestamps to 2106 on 32 bit systems") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the SteelSeries Stratus Duo, a wireless Xbox 360
controller. The Stratus Duo ships with a USB dongle to enable wireless
connectivity, but it can also function as a wired controller by connecting
it directly to a PC via USB, hence the need for two USD PIDs. 0x1430 is the
dongle, and 0x1431 is the controller.
Otherwise we gradually leak credits leading to potential
hung session.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When executing add_credits() we currently call cifs_reconnect()
if the number of credits is zero and there are no requests in
flight. In this case we may call cifs_reconnect() recursively
twice and cause memory corruption given the following sequence
of functions:
Fix this by avoiding to call cifs_reconnect() in add_credits()
and checking for zero credits in the demultiplex thread.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do need to account for credits received in error responses
to read requests on encrypted sessions.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we mark MID as malformed if we get an error from server
in a read response. This leads to not properly processing credits
in the readv callback. Fix this by marking such a response as
normal received response and process it appropriately.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing MTU i/o we need to leave some credits for
possible reopen requests and other operations happening
in parallel. Currently we leave 1 credit which is not
enough even for reopen only: we need at least 2 credits
if durable handle reconnect fails. Also there may be
other operations at the same time including compounding
ones which require 3 credits at a time each. Fix this
by leaving 8 credits which is big enough to cover most
scenarios.
Was able to reproduce this when server was configured
to give out fewer credits than usual.
The proper fix would be to reconnect a file handle first
and then obtain credits for an MTU request but this leads
to bigger code changes and should happen in other patches.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_VGACON_SOFT_SCROLLBACK is selected, the VGA display memory
index and vc_visible_origin don't change when scrollback is activated.
The actual screen content is saved away and the scrollbackdata is copied
over it. However the vt code, and /dev/vcs devices in particular, still
expect vc_origin to always point at the actual screen content not the
displayed scrollback content.
So adjust vc_origin to point at the saved screen content when scrollback
is active and set it back to vc_visible_origin when restoring the screen.
This fixes /dev/vcsa<n> that return scrollback content when they
shouldn't (onli /dev/vcsa without a number should), and also fixes
/dev/vcsu that should return scrollback content when scrollback is
active but currently doesn't.
An unnecessary call to vga_set_mem_top() is also removed.
fc96df16a1ce is good and can already fix the "return stack garbage" issue,
but let's also improve hv_ringbuffer_get_debuginfo(), which would silently
return stack garbage, if people forget to check channel->state or
ring_info->ring_buffer, when using the function in the future.
Having an error check in the function would eliminate the potential risk.
Add a Fixes tag to indicate the patch depdendency.
Fixes: fc96df16a1ce ("Drivers: hv: vmbus: Return -EINVAL for the sys files for unopened channels") Cc: stable@vger.kernel.org Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyper-V memory hotplug protocol has 2M granularity and in Linux x86 we use
128M. To deal with it we implement partial section onlining by registering
custom page onlining callback (hv_online_page()). Later, when more memory
arrives we try to online the 'tail' (see hv_bring_pgs_online()).
It was found that in some cases this 'tail' onlining causes issues:
Turns out that we now have deferred struct page initialization for memory
hotplug so e.g. memory_block_action() in drivers/base/memory.c does
pages_correctly_probed() check and in that check it avoids inspecting
struct pages and checks sections instead. But in Hyper-V balloon driver we
do PageReserved(pfn_to_page()) check and this is now wrong.
Fix __might_sleep warning[1] in tty/n_hdlc.c read due to copy_to_user
call while current is TASK_INTERRUPTIBLE. This is a false positive
since the code path does not depend on current state remaining
TASK_INTERRUPTIBLE. The loop breaks out and sets TASK_RUNNING after
calling copy_to_user.
This patch supresses the warning by setting TASK_RUNNING before calling
copy_to_user.
We were experiencing a crash similar to the one reported as part of
commit:a5ba1d95e46e ("uart: fix race between uart_put_char() and
uart_shutdown()") in our testbed as well. We continue to observe the same
crash after integrating the commit a5ba1d95e46e ("uart: fix race between
uart_put_char() and uart_shutdown()")
On reviewing the change, the port lock should be taken prior to checking for
if (!circ->buf) in fn. __uart_put_char and other fns. that update the buffer
uart_state->xmit.
Traceback:
[11/27/2018 06:24:32.4870] Unable to handle kernel NULL pointer dereference
at virtual address 0000003b
Some tty line disciplines do not have a receive buf callback, so
properly check for that before calling it. If they do not have this
callback, just eat the character quietly, as we can't fail this call.
Because the irq was requested through device managed resources API
(devm_request_threaded_irq()) it was freed after meson_mmc_remove()
completion, thus after mmc_free_host() has reclaimed meson_host memory.
As this irq is IRQF_SHARED, while using CONFIG_DEBUG_SHIRQ, its handler
get called by free_irq(). So meson_mmc_irq() was called after the
meson_host memory reclamation and was using invalid memory.
We ended up with the following scenario:
device_release_driver()
meson_mmc_remove()
mmc_free_host() /* Freeing host memory */
...
devres_release_all()
devm_irq_release()
__free_irq()
meson_mmc_irq() /* Uses freed memory */
To avoid this, the irq is released in meson_mmc_remove() and in
mseon_mmc_probe() error path before mmc_free_host() gets called.
We need to handle mmc_of_parse() errors during probe.
This finally fixes the wifi regression on Raspberry Pi 3 series.
In error case the wifi chip was permanently in reset because of
the power sequence depending on the deferred probe of the GPIO expander.
Fix this by sanitizing ipcnum before using it to index pDrvData->IPCs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
When calling smp_call_ipl_cpu() from the IPL CPU, we will try to read
from pcpu_devices->lowcore. However, due to prefixing, that will result
in reading from absolute address 0 on that CPU. We have to go via the
actual lowcore instead.
This means that right now, we will read lc->nodat_stack == 0 and
therfore work on a very wrong stack.
This BUG essentially broke rebooting under QEMU TCG (which will report
a low address protection exception). And checking under KVM, it is
also broken under KVM. With 1 VCPU it can be easily triggered.
smp_rescan_cpus() is called without the device_hotplug_lock, which can lead
to a dedlock when a new CPU is found and immediately set online by a udev
rule.
This was observed on an older kernel version, where the cpu_hotplug_begin()
loop was still present, and it resulted in hanging chcpu and systemd-udev
processes. This specific deadlock will not show on current kernels. However,
there may be other possible deadlocks, and since smp_rescan_cpus() can still
trigger a CPU hotplug operation, the device_hotplug_lock should be held.
For reference, this was the deadlock with the old cpu_hotplug_begin() loop:
chcpu (rescan) systemd-udevd
echo 1 > /sys/../rescan
-> smp_rescan_cpus()
-> (*) get_online_cpus()
(increases refcount)
-> smp_add_present_cpu()
(new CPU found)
-> register_cpu()
-> device_add()
-> udev "add" event triggered -----------> udev rule sets CPU online
-> echo 1 > /sys/.../online
-> lock_device_hotplug_sysfs()
(this is missing in rescan path)
-> device_online()
-> (**) device_lock(new CPU dev)
-> cpu_up()
-> cpu_hotplug_begin()
(loops until refcount == 0)
-> deadlock with (*)
-> bus_probe_device()
-> device_attach()
-> device_lock(new CPU dev)
-> deadlock with (**)
Fix this by taking the device_hotplug_lock in the CPU rescan path.
Right now the early machine detection code check stsi 3.2.2 for "KVM"
and set MACHINE_IS_VM if this is different. As the console detection
uses diagnose 8 if MACHINE_IS_VM returns true this will crash Linux
early for any non z/VM system that sets a different value than KVM.
So instead of assuming z/VM, do not set any of MACHINE_IS_LPAR,
MACHINE_IS_VM, or MACHINE_IS_KVM.
CC: stable@vger.kernel.org Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASCE of an mm_struct can be modified after a task has been created,
e.g. via crst_table_downgrade for a compat process. The active_mm logic
to avoid the switch_mm call if the next task is a kernel thread can
lead to a situation where switch_mm is called where 'prev == next' is
true but 'prev->context.asce == next->context.asce' is not.
This can lead to a situation where a CPU uses the outdated ASCE to run
a task. The result can be a crash, endless loops and really subtle
problem due to TLBs being created with an invalid ASCE.
Cc: stable@kernel.org # v3.15+ Fixes: 53e857f30867 ("s390/mm,tlb: race of lazy TLB flush vs. recreation") Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While "s390/vdso: avoid 64-bit vdso mapping for compat tasks" fixed
64-bit vdso mapping for compat tasks under gdb it introduced another
problem. "compat_mm" flag is not inherited during fork and when
31-bit process forks a child (but does not perform exec) it ends up
with 64-bit vdso. To address that, init_new_context (which is called
during fork and exec) now initialize compat_mm based on thread TIF_31BIT
flag. Later compat_mm is adjusted in arch_setup_additional_pages, which
is called during exec.
So far we've mapped branches to "ijmp" which also counts conditional
branches NOT taken. This makes us different from other architectures
such as ARM which seem to be counting only taken branches.
So use "ijmptak" hardware condition which only counts (all jump
instructions that are taken)
'ijmptak' event is available on both ARCompact and ARCv2 ISA based
cores.
In setup_arch_memory we reserve the memory area wherein the kernel
is located. Current implementation may reserve more memory than
it actually required in case of CONFIG_LINUX_LINK_BASE is not
equal to CONFIG_LINUX_RAM_BASE. This happens because we calculate
start of the reserved region relatively to the CONFIG_LINUX_RAM_BASE
and end of the region relatively to the CONFIG_LINUX_RAM_BASE.
For example in case of HSDK board we wasted 256MiB of physical memory:
------------------->8------------------------------
Memory: 770416K/1048576K available (5496K kernel code,
240K rwdata, 1064K rodata, 2200K init, 275K bss,
278160K reserved, 0K cma-reserved)
------------------->8------------------------------
Fix that.
Fixes: 9ed68785f7f2b ("ARC: mm: Decouple RAM base address from kernel link addr") Cc: stable@vger.kernel.org #4.14+ Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARCv2 optimized memset uses PREFETCHW instruction for prefetching the
next cache line but doesn't ensure that the line is not past the end of
the buffer. PRETECHW changes the line ownership and marks it dirty,
which can cause issues in SMP config when next line was already owned by
other core. Fix the issue by avoiding the PREFETCHW
Some more details:
The current code has 3 logical loops (ignroing the unaligned part)
(a) Big loop for doing aligned 64 bytes per iteration with PREALLOC
(b) Loop for 32 x 2 bytes with PREFETCHW
(c) any left over bytes
loop (a) was already eliding the last 64 bytes, so PREALLOC was
safe. The fix was removing PREFETCW from (b).
Another potential issue (applicable to configs with 32 or 128 byte L1
cache line) is that PREALLOC assumes 64 byte cache line and may not do
the right thing specially for 32b. While it would be easy to adapt,
there are no known configs with those lie sizes, so for now, just
compile out PREALLOC in such cases.
The fixed clocks in the DTS file have a hyphen, but the clock driver has
the fixed clocks using underbar. Thus the clock driver cannot detect the
other fixed clocks correctly. Change the fixed clock names to a hyphen.
Fix memory allocation and use struct_size() in kzalloc(). This also
fixes the allocation size to be correct, and smaller, because before we
were allocating a bunch of sizeof(struct clk_hw_onecell_data) structures
for each struct clk_hw we needed.
Fixes: 3fde0e16d016 ("drivers: clk: Add ZynqMP clock driver") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
[sboyd@kernel.org: Expand commit text] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the bootup of the kernel, the DAPM bias level is in the OFF
state. As soon as the DAPM framework kicks in it pushes the codec
into STANDBY state.
The probe function doesn't prepare the clock, and STANDBY state
does a clk_disable_unprepare() without checking the previous state.
This leads to an OOPS.
Not transitioning from an OFF state to the STANDBY state fixes the
problem.
Signed-off-by: b-ak <anur.bhargav@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snap realm and corresponding inode have pointers to each other.
The two pointer should get clear at the same time. Otherwise,
snap realm's pointer may reference freed inode.
There is a bug in the current GPIO code for ftdi_sio: it failed to take USB
autosuspend into account. If the device is in autosuspend, calls to
usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for
autosuspend timeout is usually 2-5 seconds, this made it almost impossible
to use the GPIOs on machines that have USB autosuspend enabled. This patch
fixes the issue by acquiring a PM lock on the device for the duration of
the USB transfers. Tested on an FT231X device.
The patch "usb: simplify usbport trigger" together with "leds: triggers:
add device attribute support" caused an regression for the usbport
trigger. it will no longer enumerate any active usb hub ports under the
"ports" directory in the sysfs class directory, if the usb host drivers
are fully initialized before the usbport trigger was loaded.
The reason is that the usbport driver tries to register the sysfs
entries during the activate() callback. And this will fail with -2 /
ENOENT because the patch "leds: triggers: add device attribute support"
made it so that the sysfs "ports" group was only being added after the
activate() callback succeeded.
This version of the patch reverts parts of the "usb: simplify usbport
trigger" patch and restores usbport trigger's functionality.
When using Kerberos with v4.20, I've observed frequent connection
loss on heavy workloads. I traced it down to the client underrunning
the GSS sequence number window -- NFS servers are required to drop
the RPC with the low sequence number, and also drop the connection
to signal that an RPC was dropped.
Bisected to commit 918f3c1fe83c ("SUNRPC: Improve latency for
interactive tasks").
I've got a one-line workaround for this issue, which is easy to
backport to v4.20 while a more permanent solution is being derived.
Essentially, tk_owner-based sorting is disabled for RPCs that carry
a GSS sequence number.
Fixes: 918f3c1fe83c ("SUNRPC: Improve latency for interactive ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intention in the previous patch was to only place the processor
tables in the .rodata section if big.Little was being built and we
wanted the branch target hardening, but instead (due to the way it
was tested) it ended up always placing the tables into the .rodata
section.
Although harmless, let's correct this anyway.
Fixes: 3a4d0c2172bc ("ARM: ensure that processor vtables is not lost after boot") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We forgot to update ip6erspan version related info when changing link,
which will cause setting new hwid failed.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 94d7d8f292870 ("ip6_gre: add erspan v2 support") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Different frame variants known as "ERSPAN Types" can be
distinguished based on the GRE "Protocol Type" field value: Type I
and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].
So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().
Fixes: 94d7d8f29287 ("ip6_gre: add erspan v2 support") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In changelink ops, the ip6gre_net pointer is retrieved from
dev_net(dev), which is wrong in case of x-netns. Thus, the tunnel is not
unlinked from its current list and is relinked into another net
namespace. This corrupts the tunnel lists and can later trigger a kernel
oops.
Fix this by retrieving the netns from device private area.
Fixes: c8632fc30bb0 ("net: ip6_gre: Split up ip6gre_changelink()") Cc: Petr Machata <petrm@mellanox.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failure __ip_append_data triggers udp_flush_pending_frames, but these
tests happen later. The skb must be freed directly.
Fixes: bec1f6f697362 ("udp: generate gso with UDP_SEGMENT") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent changes (especially 05cd271fd61a ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.
v2:
- use kzalloc() instead of kcalloc()
Fixes: 05cd271fd61a ("cls_flower: Support multiple masks per priority") Cc: Jiri Pirko <jiri@resnulli.us> Cc: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ido Schimmel [Fri, 18 Jan 2019 15:57:55 +0000 (15:57 +0000)]
mlxsw: pci: Ring CQ's doorbell before RDQ's
When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).
In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.
The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.
Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.
Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.
Before commit 8404f6f2e8ed ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.
Fixes: 8404f6f2e8ed ("mlxsw: pci: Allow to use CQEs of version 1 and version 2") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Semion Lisyansky <semionl@mellanox.com> Tested-by: Semion Lisyansky <semionl@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a tc flower action of egress mirred redirect, the driver adds
an implicit FID setting action. This implicit action sets a dummy FID to
the packet and is used as part of a design for trapping unmatched flows
in OVS. While this implicit FID setting action is supposed to be a NOP
when a redirect action is added, in Spectrum-2 the FID record is
consulted as the dummy FID index is an 802.1D FID index and the packet
is dropped instead of being redirected.
Set the dummy FID index value to be within 802.1Q range. This satisfies
both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it
as an 802.1Q FID and will then follow the redirect action.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC") Signed-off-by: Nir Dotan <nird@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. In response to events in the netdev and inetaddr notification chains
2. When a network namespace is being dismantled
In both cases only routes associated with a dead nexthop group are
flushed. However, a nexthop group will only be marked as dead in case it
is populated with actual nexthops using a nexthop device. This is not
the case when the route in question is an error route (e.g.,
'blackhole', 'unreachable').
Therefore, when a network namespace is being dismantled such routes are
not flushed and leaked [1].
To reproduce:
# ip netns add blue
# ip -n blue route add unreachable 192.0.2.0/24
# ip netns del blue
Fix this by not skipping error routes that are not marked with
RTNH_F_DEAD when flushing the routing tables.
To prevent the flushing of such routes in case #1, add a parameter to
fib_table_flush() that indicates if the table is flushed as part of
namespace dismantle or not.
Note that this problem does not exist in IPv6 since error routes are
associated with the loopback device.
Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC") Signed-off-by: Nir Dotan <nird@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vhost dirty page logging API is designed to sync through GPA. But we
try to log GIOVA when device IOTLB is enabled. This is wrong and may
lead to missing data after migration.
To solve this issue, when logging with device IOTLB enabled, we will:
1) reuse the device IOTLB translation result of GIOVA->HVA mapping to
get HVA, for writable descriptor, get HVA through iovec. For used
ring update, translate its GIOVA to HVA
2) traverse the GPA->HVA mapping to get the possible GPA and log
through GPA. Pay attention this reverse mapping is not guaranteed
to be unique, so we should log each possible GPA in this case.
This fix the failure of scp to guest during migration. In -next, we
will probably support passing GIOVA->GPA instead of GIOVA->HVA.
Fixes: 6b1e6cc7855b ("vhost: new device IOTLB API") Reported-by: Jintack Lim <jintack@cs.columbia.edu> Cc: Jintack Lim <jintack@cs.columbia.edu> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For nested and variable attributes, the expected length of an attribute
is not known and marked by a negative number. This results in an OOB
read when the expected length is later used to check if the attribute is
all zeros. Fix this by using the actual length of the attribute rather
than the expected length.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin reported a set of filters don't work after changing
from reclassify to continue. Looking into the code, it
looks like skb protocol is not always fetched for each
iteration of the filters. But, as demonstrated by Martin,
TC actions could modify skb->protocol, for example act_vlan,
this means we have to refetch skb protocol in each iteration,
rather than using the one we fetch in the beginning of the loop.
This bug is _not_ introduced by commit 3b3ae880266d
("net: sched: consolidate tc_classify{,_compat}"), technically,
if act_vlan is the only action that modifies skb protocol, then
it is commit c7e2b9689ef8 ("sched: introduce vlan action") which
introduced this bug.
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the tunnel_key action is replaced, the kernel forgets to release the
dst metadata: ensure they are released by tunnel_key_init(), the same way
it's done in tunnel_key_release().
Fixes: d0f6dd8a914f4 ("net/sched: Introduce act_tunnel_key") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap") Reported-by: Scott Wood <oss@buserror.net> Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code in __mdiobus_register() doesn't properly handle
failures returned by the devm_gpiod_get_optional() call: it returns
immediately, without unregistering the device that was added by the
call to device_register() earlier in the function.
This leaves a stale device, which then causes a NULL pointer
dereference in the code that handles deferred probing:
The actual error that we had from devm_gpiod_get_optional() was
-EPROBE_DEFER, due to the GPIO being provided by a driver that is
probed later than the Ethernet controller driver.
To fix this, we simply add the missing device_del() invocation in the
error path.
Fixes: 69226896ad636 ("mdio_bus: Issue GPIO RESET to PHYs") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660dd ("bridge: use is_skb_forwardable in forward path") Cc: bridge@lists.linux-foundation.org Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XGBE hardware has support for performing MDIO operations using an
MDIO command request. The driver mistakenly uses the mdio port address
as the MDIO command request device address instead of the MDIO command
request port address. Additionally, the driver does not properly check
for and create a clause 45 MDIO command.
Check the supplied MDIO register to determine if the request is a clause
45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device
address and register number from the supplied MDIO register and use them
to set the MDIO command request device address and register number fields.
For a clause 22 operation, the MDIO request device address is set to zero
and the MDIO command request register number is set to the supplied MDIO
register. In either case, the supplied MDIO port address is used as the
MDIO command request port address.
Fixes: 732f2ab7afb9 ("amd-xgbe: Add support for MDIO attached PHYs") Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some IPMI modules (e.g. ibmpex_msg_handler()) will have ipmi_usr_hdlr
handlers that call ipmi_free_recv_msg() directly. This will essentially
kfree(msg), leading to use-after-free.
This does not happen in the ipmi_devintf module, which will queue the
message and run ipmi_free_recv_msg() later.
BUG: KASAN: use-after-free in deliver_response+0x12f/0x1b0
Read of size 8 at addr ffff888a7bf20018 by task ksoftirqd/3/27
CPU: 3 PID: 27 Comm: ksoftirqd/3 Tainted: G O 4.19.11-amd64-ani99-debug #12.0.1.601133+pv
Hardware name: AppNeta r1000/X11SPW-TF, BIOS 2.1a-AP 09/17/2018
Call Trace:
dump_stack+0x92/0xeb
print_address_description+0x73/0x290
kasan_report+0x258/0x380
deliver_response+0x12f/0x1b0
? ipmi_free_recv_msg+0x50/0x50
deliver_local_response+0xe/0x50
handle_one_recv_msg+0x37a/0x21d0
handle_new_recv_msgs+0x1ce/0x440
...
Allocated by task 9885:
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc_trace+0x116/0x290
ipmi_alloc_recv_msg+0x28/0x70
i_ipmi_request+0xb4a/0x1640
ipmi_request_settime+0x1b8/0x1e0
...
Fix this by sanitizing channel and addr->channel before using them to
index user->intf->addrinfo and intf->addrinfo, correspondingly.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
The IPMI driver was recently modified to use SRCU, but it turns out
this uses a chunk of percpu memory, even if IPMI is never used.
So modify thing to on initialize on the first use. There was already
code to sort of handle this for handling init races, so piggy back
on top of that, and simplify it in the process.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Reported-by: Tejun Heo <tj@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: stable@vger.kernel.org # 4.18 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the user->release_barrier.rda is freed in ipmi_destroy_user(), but
the refcount is not zero, when acquire_ipmi_user() uses user->release_barrier.rda
in __srcu_read_lock(), it causes oops.
Fix this by calling cleanup_srcu_struct() when the refcount is zero.
Fixes: e86ee2d44b44 ("ipmi: Rework locking and shutdown for hot remove") Cc: stable@vger.kernel.org # 4.18 Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.
Avoid the misleading error and silently bail out from the function in
case the received event is a command status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by Adam Ford <aford173@gmail.com> #4.19.16 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
The cursor vanishes when touching the top of edge of the screen for
Raven on Linux.
This occurs because the cursor height is not taken into account when
deciding to disable the cursor.
[How]
Factor in the cursor height into the cursor calculations - and mimic
the existing x position calculations.
Fixes: 94a4ffd1d40b ("drm/amd/display: fix PIP bugs on Dal3") Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kmemleak does not play well with KASAN (tested on both HPE Apollo 70 and
Huawei TaiShan 2280 aarch64 servers).
After calling start_kernel()->setup_arch()->kasan_init(), kmemleak early
log buffer went from something like 280 to 260000 which caused kmemleak
disabled and crash dump memory reservation failed. The multitude of
kmemleak_alloc() calls is from nested loops while KASAN is setting up full
memory mappings, so let early kmemleak allocations skip those
memblock_alloc_internal() calls came from kasan_init() given that those
early KASAN memory mappings should not reference to other memory. Hence,
no kmemleak false positives.
Patch series "THP eligibility reporting via proc".
This series of three patches aims at making THP eligibility reporting much
more robust and long term sustainable. The trigger for the change is a
regression report [2] and the long follow up discussion. In short the
specific application didn't have good API to query whether a particular
mapping can be backed by THP so it has used VMA flags to workaround that.
These flags represent a deep internal state of VMAs and as such they
should be used by userspace with a great deal of caution.
A similar has happened for [3] when users complained that VM_MIXEDMAP is
no longer set on DAX mappings. Again a lack of a proper API led to an
abuse.
The first patch in the series tries to emphasise that that the semantic of
flags might change and any application consuming those should be really
careful.
The remaining two patches provide a more suitable interface to address [2]
and provide a consistent API to query the THP status both for each VMA and
process wide as well. [1]
Even though vma flags exported via /proc/<pid>/smaps are explicitly
documented to be not guaranteed for future compatibility the warning
doesn't go far enough because it doesn't mention semantic changes to those
flags. And they are important as well because these flags are a deep
implementation internal to the MM code and the semantic might change at
any time.
Let's consider two recent examples:
http://lkml.kernel.org/r/20181002100531.GC4135@quack2.suse.cz
: commit e1fb4a086495 "dax: remove VM_MIXEDMAP for fsdax and device dax" has
: removed VM_MIXEDMAP flag from DAX VMAs. Now our testing shows that in the
: mean time certain customer of ours started poking into /proc/<pid>/smaps
: and looks at VMA flags there and if VM_MIXEDMAP is missing among the VMA
: flags, the application just fails to start complaining that DAX support is
: missing in the kernel.
http://lkml.kernel.org/r/alpine.DEB.2.21.1809241054050.224429@chino.kir.corp.google.com
: Commit 1860033237d4 ("mm: make PR_SET_THP_DISABLE immediately active")
: introduced a regression in that userspace cannot always determine the set
: of vmas where thp is ineligible.
: Userspace relies on the "nh" flag being emitted as part of /proc/pid/smaps
: to determine if a vma is eligible to be backed by hugepages.
: Previous to this commit, prctl(PR_SET_THP_DISABLE, 1) would cause thp to
: be disabled and emit "nh" as a flag for the corresponding vmas as part of
: /proc/pid/smaps. After the commit, thp is disabled by means of an mm
: flag and "nh" is not emitted.
: This causes smaps parsing libraries to assume a vma is eligible for thp
: and ends up puzzling the user on why its memory is not backed by thp.
In both cases userspace was relying on a semantic of a specific VMA flag.
The primary reason why that happened is a lack of a proper interface.
While this has been worked on and it will be fixed properly, it seems that
our wording could see some refinement and be more vocal about semantic
aspect of these flags as well.
Link: http://lkml.kernel.org/r/20181211143641.3503-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Jan Kara <jack@suse.cz> Acked-by: Dan Williams <dan.j.williams@intel.com> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Mike Rapoport <rppt@linux.ibm.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Dan Williams <dan.j.williams@intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Paul Oppenheimer <bepvte@gmail.com> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the process being tracked does mremap() without
UFFD_FEATURE_EVENT_REMAP on the corresponding tracking uffd file handle,
we should not generate the remap event, and at the same time we should
clear all the uffd flags on the new VMA. Without this patch, we can still
have the VM_UFFD_MISSING|VM_UFFD_WP flags on the new VMA even the fault
handling process does not even know the existance of the VMA.
Link: http://lkml.kernel.org/r/20181211053409.20317-1-peterx@redhat.com Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Reviewed-by: William Kucharski <william.kucharski@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Cc: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Pravin Shedge <pravin.shedge4linux@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log