Merge tag 'zynqmp-dt-for-v5.13' of https://github.com/Xilinx/linux-xlnx into arm/dt
arm64: dts: ZynqMP DT changes for v5.13
- Add power-domains for DP
- Remove si5328 node without compatible string
* tag 'zynqmp-dt-for-v5.13' of https://github.com/Xilinx/linux-xlnx:
arm64: dts: zynqmp: Remove si5328 device nodes
arm64: dts: zynqmp: Add power domain for the DisplayPort DMA controller
Merge tag 'v5.13-rockchip-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New board the NanoPi R4S, OPP adjustments on rk3399 (sync with vendor
and using ranged values to allow better compatibility with regulator
steps), gpu opps on px30, infrared receiver on rockpro64,
USB3 support on rk3328, MMC alias fixups, dt-compatible fixes.
* tag 'v5.13-rockchip-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: move mmc aliases to board dts on rk3399
arm64: dts: rockchip: move mmc aliases to board dts on rk3368
arm64: dts: rockchip: move mmc aliases to board dts on rk3328
arm64: dts: rockchip: move mmc aliases to board dts on rk3308
arm64: dts: rockchip: move mmc aliases to board dts on px30
arm64: dts: rockchip: add new watchdog compatible to rk3399.dtsi
arm64: dts: rockchip: add new watchdog compatible to rk3328.dtsi
arm64: dts: rockchip: add new watchdog compatible to rk3308.dtsi
arm64: dts: rockchip: add new watchdog compatible to px30.dtsi
arm64: dts: rockchip: enable dwc3 usb for A95X Z2
arm64: dts: rockchip: add rk3328 dwc3 usb controller node
rockchip: rk3399: Add support for FriendlyARM NanoPi R4S
dt-bindings: Add doc for FriendlyARM NanoPi R4S
arm64: dts: rockchip: add phandle to timer0 on rk3368
arm64: dts: rockchip: add infrared receiver node to rockpro64
arm64: dts: rockchip: drop separate opp table on rk3399-puma
arm64: dts: rockchip: used range'd gpu opps on rk3399
arm64: dts: rockchip: synchronize rk3399 opps with vendor kernel
arm64: dts: rockchip: Add gpu opp nodes to px30 dtsi
Nicolas Ferre [Thu, 8 Apr 2021 16:44:43 +0000 (18:44 +0200)]
ARM: dts: at91: sama5d2/trivial: fix letter case for etm hex address
Fix the etm node hex address to lower case for matching regexp
specification and removing the additional warning that looks like:
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dt.yaml: /: 'etm@73C000' does not
match any of the regexes: '@(0|[1-9a-f][0-9a-f]*)$', '^[^@]+$',
'pinctrl-[0-9]+'
As suggested by Arnd Bergmann, mmc-aliases are supposed to be
board-specific, so move the newly added general aliases to
the board-level on rv1108-based boards.
As suggested by Arnd Bergmann, mmc-aliases are supposed to be
board-specific, so move the newly added general aliases to
the board-level on rk322x-based boards.
Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: amlogic: updates for v5.13 (round 2)
- updates/cleanups for Hardkernel Odroid N2/N2+
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: add GPIO line names to ODROID N2/N2+
arm64: dts: meson: add saradc node to ODROID N2/N2+
arm64: dts: meson: remove extra tab from ODROID N2/N2+ ext_mdio node
Merge tag 'qcom-arm64-for-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
More Qualcomm ARM64 DT updates for 5.13
This adds RPMh regulators, coresight, AOSS qmp, ipcc, llcc for the
SC7280. It adds interconnect, PRNG and thermal pieces to SM8350. It
specifies the now required clocks for the SDM845 gcc, corrects the
firmware-name for adsp and cdsp on the db845c and defines DSI and panel
bits for Xiaomi Pocophone F1.
SM8150 gains iommu settings and the remaining I2C controllers and SM8250
gains Venus and the QMP PHY is updated to include the DP portion.
It adds the MSM8998 based OnePlus 5/5T device and enables sound support
on the Trogdor device family.
Lastly it adds the GIC hypervisor registers & interrupt for when Linux
is booted in EL2 on MSM8916.
* tag 'qcom-arm64-for-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (25 commits)
arm64: dts: qcom: update usb qmp phy clock-cells property
arm64: dts: qcom: msm8916: Add GICv2 hypervisor registers/interrupt
arm64: dts: sdm845-db845c: make firmware filenames follow linux-firmware
arm64: dts: qcom: sdm845-xiaomi-beryllium: Add DSI and panel bits
arm64: dts: qcom: sc7280: Add Coresight support
arm64: dts: qcom: sc7280: Add AOSS QMP node
arm64: dts: qcom: sc7280: Add IPCC for SC7280 SoC
arm64: dts: qcom: sc7280: Add device tree node for LLCC
arm64: dts: qcom: Add support for OnePlus 5/5T
arm64: dts: qcom: msm8998: Disable MSS remoteproc by default
arm64: dts: qcom: Move rmtfs memory region
arm64: dts: qcom: Add sound node for sc7180-trogdor-coachz
arm64: dts: qcom: sc7180-trogdor: Add lpass dai link for I2S driver
arm64: dts: qcom: use dp_phy to provide clocks to dispcc
arm64: dts: qcom: sm8250: switch usb1 qmp phy to USB3+DP mode
arm64: dts: qcom: sm8250: Add venus DT node
arm64: dts: qcom: sm8250: Add videocc DT node
arm64: dts: qcom: sm8350: Add interconnects
arm64: dts: qcom: sm8350: Add support for PRNG EE
arm64: dts: qcom: sc7280: Add RPMh regulators for sc7280-idp
...
Merge tag 'qcom-dts-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm dts updates for v5.13
This adds Bluetooth support on the Samsung Galaxy S5, corrects the mount
matrix for the IMU on Nexus 5 and corrects the fuel gauge irq trigger
for the two devices.
* tag 'qcom-dts-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974-klte: Add bluetooth support
ARM: dts: qcom: msm8974: add blsp2_uart8
ARM: dts: qcom: msm8974-samsung-klte: correct fuel gauge interrupt trigger level
ARM: dts: qcom: msm8974-lge-nexus5: correct fuel gauge interrupt trigger level
ARM: dts: qcom: msm8974-hammerhead: add mount matrix for IMU
arch/arm/boot/dts/armada-385-atl-x530.dts:171.14-199.4: Warning (spi_bus_reg): /soc/spi@10680/spi-flash@0: SPI bus unit address format error, expected "1"
I assume the "reg" property is correct here, so adjust the unit address
accordingly.
Fixes: c6dfc019c239 ("ARM: dts: mvebu: Add device tree for ATL-x530 Board") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: kernelci.org bot <bot@kernelci.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ARM Cortex-A53 CPU cores and QGIC2 interrupt controller
(an implementation of the ARM GIC 2.0 specification) used in MSM8916
support virtualization, e.g. for KVM on Linux. However, so far it was
not possible to make use of this functionality, because Qualcomm's
proprietary "hyp" firmware blocks the EL2 mode of the CPU and only
allows booting Linux in EL1.
However, on devices without (firmware) secure boot there is no need
to rely on all of Qualcomm's firmware. The "hyp" firmware on MSM8916
seems simple enough that it can be replaced with an open-source
alternative created only based on trial and error - with some similar
EL2/EL1 initialization code adapted from Linux and U-Boot.
qhypstub [1] is such an open-source firmware for MSM8916 that
can be used as drop-in replacement for Qualcomm's "hyp" firmware.
It does not implement any hypervisor functionality.
Instead, it allows booting Linux/KVM (or other hypervisors) in EL2.
With Linux booting in EL2, KVM seems to be working just fine on MSM8916.
However, so far it is not possible to make use of the virtualization
features in the GICv2. To use KVM's VGICv2 code, the QGIC2 device tree
node needs additional resources (according to binding documentation):
- The CPU interface region (second reg) must be at least 8 KiB large
to access the GICC_DIR register (mapped at 0x1000 offset)
- Virtual control/CPU interface register base and size
- Hypervisor maintenance interrupt
Fortunately, the public APQ8016E TRM [2] provides the required information:
- The CPU interface region (at 0x0B002000) actually has a size of 8 KiB
- Virtual control/CPU interface register is at 0x0B001000/0x0B004000
- Hypervisor maintenance interrupt is "PPI #0"
Note: This is a bit strange since almost all other ARM SoCs use
GIC_PPI 9 for this. However, I have verified that this is
indeed the interrupt that fires when bits are set in GICH_HCR.
Add the additional resources to the QGIC2 device tree node in msm8916.dtsi.
There is no functional difference when Linux is started in EL1 since the
additional resources are ignored in that case.
With these changes (and qhypstub), KVM seems to be fully working on
the DragonBoard 410c (apq8016-sbc) and BQ Aquaris X5 (longcheer-l8910).
Nichole Wang [Tue, 30 Mar 2021 02:08:08 +0000 (10:08 +0800)]
ARM: dts: aspeed: mihawk: Add GPIO line names
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Eddie James [Mon, 29 Mar 2021 15:00:18 +0000 (10:00 -0500)]
ARM: dts: aspeed: everest: Enable fan watchdog
Set watchdog 1 to pulse the fan watchdog circuit that drives the FAULT
pin of the MAX31785, resulting in fans running at full speed, if at
any point the BMC stops pulsing it, such as a BMC reboot at runtime.
Enable watchdog 2 for BMC reboots.
Eddie James [Mon, 29 Mar 2021 15:00:09 +0000 (10:00 -0500)]
ARM: dts: aspeed: rainier 4U: Fix fan configuration
The 4U fans didn't have the correct properties since the fan nodes
were redefined. Fix this by referencing each fan individually and
adding the differences to the 4U fans.
Eddie James [Mon, 29 Mar 2021 15:00:08 +0000 (10:00 -0500)]
ARM: dts: aspeed: rainier: Enable fan watchdog
Set watchdog 1 to pulse the fan watchdog circuit that drives the FAULT
pin of the MAX31785, resulting in fans running at full speed, if at
any point the BMC stops pulsing it, such as a BMC reboot at runtime.
Enable watchdog 2 for BMC reboots.
Rainier has two dual-chip modules and therefore four CFAMs with their
associated engines. Add these to the devicetree with the i2c busses
that have devices on them.
This is a relatively low-cost AST2500-based Xeon E-2100/E-2200 series
mini-ITX board that we hope can provide a decent platform for OpenBMC
development.
This initial device-tree provides the necessary configuration for
basic BMC functionality such as host power control, serial console and
KVM support, and POST code snooping.
Aryan Srivastava [Mon, 30 Nov 2020 22:35:07 +0000 (11:35 +1300)]
ARM: dts: mvebu: Add device tree for ATL-x530 Board
Add device tree file for x530 board. This has an Armada 385 SoC. Has
NAND-flash for user storage and SPI for booting. Covers majority of x530
and GS980MX variants.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Merge tag 'at91-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 dt for 5.13:
- two little fixes (typo, W=1)
- a change in gpio button keycode for recent boards
* tag 'at91-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2: add ETB and ETM unit name
ARM: dts: at91: change the key code of the gpio key
ARM: dts: at91: Fix a typo
Christian Hewitt [Wed, 7 Apr 2021 04:26:07 +0000 (04:26 +0000)]
arm64: dts: meson: remove extra tab from ODROID N2/N2+ ext_mdio node
Remove an extra tab from the ext_mdio node in the ODROID N2/N2+ common
dtsi file.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20210407042609.9736-2-christianshewitt@gmail.com
Merge tag 'samsung-dt64-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.13
Two cleanups in DTS without expected impact.
* tag 'samsung-dt64-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: white-space cleanups
arm64: dts: exynos: re-order Slim SSS clocks to match dtschema
Merge tag 'samsung-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.13
1. Configure battery charger and front camera on GT-I9100 phone.
2. Fix in several boards the Maxim PMIC/MUIC/fuel gauge interrupt flags
to match real type of interrupt coming from the device.
3. Correct DTS with dtschema. This brings back the commit adding input
clock to CMU in Exynos4412 Odroid which was reverted some time ago
due to unsupported deferred probes (now supported and tested).
* tag 'samsung-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add front camera support to I9100
ARM: dts: exynos: white-space cleanups
ARM: dts: exynos: replace deprecated NTC/Murata compatibles
ARM: dts: exynos: add input clock to CMU in Exynos4412 Odroid
ARM: dts: s5pv210: correct fuel gauge interrupt trigger level on Fascinate family
ARM: dts: exynos: correct PMIC interrupt trigger level on Snow
ARM: dts: exynos: correct PMIC interrupt trigger level on SMDK5250
ARM: dts: exynos: correct PMIC interrupt trigger level on P4 Note family
ARM: dts: exynos: correct PMIC interrupt trigger level on Odroid X/U3 family
ARM: dts: exynos: correct PMIC interrupt trigger level on Midas family
ARM: dts: exynos: correct MUIC interrupt trigger level on Midas family
ARM: dts: exynos: correct fuel gauge interrupt trigger level on Midas family
ARM: dts: exynos: correct fuel gauge interrupt trigger level on P4 Note family
ARM: dts: exynos: correct fuel gauge interrupt trigger level on GT-I9100
ARM: dts: exynos: add charger supply for I9100
Merge tag 'omap-for-v5.13/dt-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.13
Mostly configures addtional devices for various boards, and
updates the gpio line names for beagle boards so userspace can
optionally find the right lines:
- Use unique gpio line names for am335x-pocketbeagle
- Update omap3-echo led configuration and add ath6kl node
- Fix indentation for am3 tscadc node
- Prepare motorola-cpcap-mapphone for power supply dtbs_check_parsing
- Use unique gpio line names for am335x-boneblack.dts
Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: amlogic updates for v5.13
- new boards: MeCool KII & KIII, Minix NEO U9-H
- used fixed index for MMC devices
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: add initial device-tree for MeCool KIII Pro
arm64: dts: meson: add initial device-tree for MeCool KII Pro
dt-bindings: arm: amlogic: add MeCool KII/KIII Pro bindings
arm64: dts: amlogic: Assign a fixed index to mmc devices
arm64: dts: meson: add initial device-tree for Minix NEO U9-H
dt-bindings: arm: amlogic: add support for the Minix NEO U9-H
Alexander Shiyan [Mon, 5 Apr 2021 05:16:58 +0000 (08:16 +0300)]
ARM: dts: clps711x: Add an empty chosen node to top level DTSI
Missing "chosen" node can cause issues when booting a kernel
with a boot-loader that doesn't create a chosen node if this
isn't present in the DTB since the decompressor relies on a
pre-existing chosen node to be available to insert the command
line and merge other ATAGS info.
Alexander Shiyan [Mon, 5 Apr 2021 05:16:54 +0000 (08:16 +0300)]
ARM: dts: clps711x: Add SYSCON nodes where it is used
This patch adds SYSCON descriptors to framebuffer, SPI, DAI
and modem control GPIO nodes to further rework these drivers
to remove the call to the syscon_regmap_lookup_by_compatible() function.
Merge tag 'qcom-arm64-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for 5.13
This extends the initial SM8350 description merged in v5.12 with
CPUfreq, SMMU, UFS, RPMHPD, SPMI, USB and remoteproc support. It adds
initial PMIC definitions for the 6 PMICs found on the MTP and it
introduces the new SM8350 Hardware Development Kit (HDK).
SC7180 is further polished, the DisplayPort portion of the QMP phy is
defined and several new SKUs of the Trogdor devices are introduced.
The new SC7280 platform is introduced, with RPMH, RPMHPD, RPMCC, SPMI,
CPU idle, SMMU and watchdog defined.
SDM845 gains the camera related nodes and some cleanups.
For SM8250 it brings some cleanups and migrates SPI0 to use GPIO for
chip select.
* tag 'qcom-arm64-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (79 commits)
arm64: dts: qcom: qrb5165-rb5: switch into using GPIO for SPI0 CS
arm64: dts: qcom: sm8250: add pinctrl for SPI using GPIO as a CS
arm64: dts: qcom: sm8250: further split of spi pinctrl config
arm64: dts: qcom: sm8250: split spi pinctrl config
arm64: dts: qcom: sdm845-db845c: Enable ov8856 sensor and connect to ISP
arm64: dts: qcom: sdm845-db845c: Configure regulators for camss node
arm64: dts: qcom: sdm845: Add CAMSS ISP node
arm64: dts: qcom: pm8150: Enable RTC
arm64: dts: qcom: sm8350-mtp: Add PMICs
arm64: dts: qcom: pmr735B: Add base dts file
arm64: dts: qcom: pmr735a: Add base dts file
arm64: dts: qcom: pm8350c: Add base dts file
arm64: dts: qcom: pm8350b: Add base dts file
arm64: dts: qcom: pm8350: Add base dts file
arm64: dts: qcom: pmk8350: Add base dts file
arm64: dts: qcom: sm8350: Add spmi node
arm64: dts: qcom: db845c: fix correct powerdown pin for WSA881x
dt-bindings: arm: qcom: Add SM8350 HDK
arm64: dts: qcom: sc7180: Drop duplicate dp_hot_plug_det node in trogdor
arm64: dts: qcom: sm8350: fix number of pins in 'gpio-ranges'
...
Merge tag 'sunxi-dt-for-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches to support the Allwinner SoCs, this time
adding:
- New secondary interrupt controller binding to support the wake-up
- Use the RSB bus instead of I2C for the PMIC on the H6
- HDMI support for the BananaPi M2-Zero
- New board: Topwise A721
* tag 'sunxi-dt-for-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: beelink-x2: Add power button
arm64: dts: allwinner: h6: Use RSB for AXP805 PMIC connection
ARM: dts: sunxi: h2-plus-bananapi-m2-zero: Add HDMI out
ARM: dts: sun4i: Add support for Topwise A721 tablet
dt-bindings: arm: Add Topwise A721
arm64: dts: allwinner: Move wakeup-capable IRQs to r_intc
arm64: dts: allwinner: Use the new r_intc binding
ARM: dts: sunxi: Move wakeup-capable IRQs to r_intc
ARM: dts: sunxi: h3/h5: Add r_intc node
ARM: dts: sunxi: Use the new r_intc binding
Merge tag 'renesas-arm-dt-for-v5.13-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.13 (take two)
- Video IN (VIN) and Camera (CSI-2) support for the R-Car M3-W+ SoC,
- LED support for the Falcon development board,
- Preparatory display pipeline support for the R-Car V3U SoC,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.13-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: ulcb: Add cpu-supply property to a57_0 node
arm64: dts: renesas: salvator-common: Add cpu-supply property to a57_0 node
arm64: dts: renesas: r8a77950: Drop operating points above 1.5 GHz
arm64: dts: renesas: r8a779a0: Fix PMU interrupt
arm64: dts: renesas: r8a779a0: Add VSPD support
arm64: dts: renesas: r8a779a0: Add FCPVD support
arm64: dts: renesas: falcon-cpu: Add GP LEDs
arm64: dts: renesas: r8a77961: Add VIN and CSI-2 device nodes
ARM: dts: koelsch: Configure pull-up for SOFT_SW GPIO keys
arm64: dts: renesas: falcon: Move AVB0 to main DTS
arm64: dts: renesas: falcon: Move watchdog config to CPU board DTS
arm64: dts: renesas: falcon: Move console config to CPU board DTS
Nicolas Ferre [Fri, 2 Apr 2021 17:01:39 +0000 (19:01 +0200)]
ARM: dts: at91: sama5d2: add ETB and ETM unit name
Add unit address to the ETB and ETM nodes.
It also allow us to get rid of the warnings:
../arch/arm/boot/dts/sama5d2.dtsi:43.6-57.4: Warning
(unit_address_vs_reg): /etb: node has a reg or ranges property, but no
unit name
../arch/arm/boot/dts/sama5d2.dtsi:59.6-73.4: Warning
(unit_address_vs_reg): /etm: node has a reg or ranges property, but no
unit name
when we compile with W=1.
ARM: dts: at91: change the key code of the gpio key
Having a button code and not a key code causes issues with libinput.
udev won't set ID_INPUT_KEY. If it is forced, then it causes a bug
within libinput.
arm64: dts: qcom: sdm845-xiaomi-beryllium: Add DSI and panel bits
Enabling the Display panel for beryllium requires DSI
labibb regulators and panel dts nodes to be added.
It is also required to keep some of the regulators as
always-on.
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20210404194437.537011-1-amit.pundir@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Jami Kettunen [Tue, 6 Apr 2021 01:07:07 +0000 (04:07 +0300)]
arm64: dts: qcom: Add support for OnePlus 5/5T
Add device trees for OnePlus 5 (cheeseburger) and 5T (dumpling)
MSM8998 SoC smartphones with initial support included for:
- UFS internal storage
- USB peripheral mode
- Display
- Touch
- Bluetooth
- Hall effect sensor
- Power and volume buttons
- Capacitive keypad button backlight (on cheeseburger)
Sujit Kautkar [Tue, 30 Mar 2021 01:46:10 +0000 (18:46 -0700)]
arm64: dts: qcom: Move rmtfs memory region
Move rmtfs memory region so that it does not overlap with system
RAM (kernel data) when KAsan is enabled. This puts rmtfs right
after mba_mem which is not supposed to increase beyond 0x94600000
arm64: dts: qcom: Add sound node for sc7180-trogdor-coachz
This is a trgodor variant, required to have sound node variable
for coachz specific platform.
Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210314061054.19451-3-srivasam@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Ajit Pandey [Sun, 14 Mar 2021 06:10:53 +0000 (11:40 +0530)]
arm64: dts: qcom: sc7180-trogdor: Add lpass dai link for I2S driver
Add dai link for supporting lpass I2S driver, which is used
for audio capture and playback.
Add lpass-cpu node with pin controls and i2s primary
and secondary dai-links.
Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Ajit Pandey <ajitp@codeaurora.org> Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org> Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org> Link: https://lore.kernel.org/r/20210314061054.19451-2-srivasam@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Add cooling maps suitable for a Noctua NF-A4/10 fan attached to the
heat sink. The fan will toggle between two speeds in operation which
seems to be normal behaviour. More fine-grained steps may help to
reduce this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Geert Uytterhoeven [Thu, 11 Mar 2021 11:05:52 +0000 (12:05 +0100)]
arm64: dts: renesas: r8a77950: Drop operating points above 1.5 GHz
The higher operating frequencies for the Cortex-A57 CPU cores, which
were first documented in the R-Car Gen3 Hardware User's Manual revision
0.54, apply to R-Car H3 ES2.0 (r8a77951).
Play it safe and restrict R-Car H3 ES1.x to 1.5 GHz, by removing the
"turbo-mode" entries from the operating points table inherited from
r8a77951.dtsi.
Merge tag 'v5.12-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
- add trivial bindings for MT8195
- fix dtbs_check warnings
- add pinmux for build-in Wifi on MT7622 evaluation borad
MT8183:
- fix USB wakeup register
- add regulator for EVB board
- add registers to mailbox consumers
- add thermal zone and trip points for CPU cooling
- Add new boards:
* ASUS Chromebook Flip CM3
* ASUS Chromebook Detachable CM3
* Acer Chromebook Spin 311
* Lenovo 10e Chromebook Tablet
MT8173:
- fix PHY property in DSI
- fix power-domain for PMIC wrapper
Pumkin:
- add MT8516 based board
- add MT8183 based board
- fix reset pin for MT8167 and MT8516 based boards
projects / users / jedix / linux-maple.git / log