Robert Marko [Sat, 9 Oct 2021 18:13:25 +0000 (20:13 +0200)]
ipq40xx: add support for MikroTik hAP ac3
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com> Tested-by: Mark Birss <markbirss@gmail.com> Tested-by: Michael Büchler <michael.buechler@posteo.net> Tested-by: Alex Tomkins <tomkins@darkzone.net>
Robert Marko [Mon, 20 Sep 2021 17:13:43 +0000 (19:13 +0200)]
base-files: dont always create kernel UBI volume
Currently nand_upgrade_tar() will pass the kernel length
to nand_upgrade_prepare_ubi() in all cases except for when
the kernel is to be installed in a separate partition as a
binary with the MTD tool.
While this is fine for almost all cases newer MikroTik NAND
devices like hAP ac3 require the kernel to be installed as a
UBIFS packed UBI volume in its own partition.
So, since we have a custom recipe to use ubiformat to flash
the kernel in its partition it makes no sense for sysupgrade
to also install the kernel as a UBI volume in the "ubi"
partition as it only wastes space and will never be used.
So, simply check whether CI_KERNPART is set to "none" and
if so unset the "has_kernel" variable which will in turn
prevent the kernel length from being passed on and then
the kernel UBI volume wont be created for no usefull purpose.
The ath79 MikroTik NAND target has been setting CI_KERNPART
to "none" for a while now altough that was not preventing
the kernel to be installed as UBI volume as well.
Robert Marko [Mon, 20 Sep 2021 10:10:07 +0000 (12:10 +0200)]
scripts: ubinize-image: make rootfs optional
Currently ubinize-image script always expects the
rootfs image to be passed and a volume for it created.
So, to allow only ubinizing a kernel for example which
the MikroTik hAP ac3 and other new NAND devices from
MikroTik require make rootfs an optional parameter like
kernel.
Hannu Nyman [Sat, 27 Nov 2021 23:09:35 +0000 (01:09 +0200)]
ath10k-ct: update version to fix DFS for VHT160
Update ath10k-ct to get the upstream fix for
DFS support for VHT160 in the 5.15 based ath10k-ct.
(Switch from 5.10 to 5.15 surfaced the upstream regression.)
Christian Lamparter [Thu, 25 Nov 2021 20:32:25 +0000 (21:32 +0100)]
gemini: try fis-index-block with 128 KiB sectors
Steven Maddox reported in the OpenWrt bugzilla, that his
RaidSonic IB-NAS4220-B was no longer booting with the new
OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was
working with the previous OpenWrt 19.07 series (uses 4.14).
(This is still under investigation.)
Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137 Reported-by: Steven Maddox <s.maddox@lantizia.me.uk> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 16 Oct 2021 19:28:52 +0000 (21:28 +0200)]
ath79: convert TP-Link Archer C7v1/2 Wifis to nvmem-cells
For v2, both ath9k (2.4GHz Wifi) and ath10k (5 GHz) driver now
pull the (pre-)calibration data from the nvmem subsystem. v1
is slightly different as only the ath9k Wifi is supported.
This allows us to move the userspace caldata extraction
and mac-address patching for the 5GHZ ath10k supported
wifi into the device-tree definition of the device.
ath9k's nodes are also changed over to use nvmem-cells
over OpenWrt's custom mtd-cal-data property.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Fri, 26 Nov 2021 08:35:45 +0000 (09:35 +0100)]
mpc85xx: backport "fix oops when CONFIG_FSL_PMC=n"
Martin Kennedy reported:
|Presently, I get this kernel panic on mpc85xx (Aerohive HiveAP 370)
|on OpenWrt 'master' which occurs right as the second processor is
|initialized:
|
|[ 0.478804] rcu: Hierarchical SRCU implementation.
|[ 0.535569] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
|[ 0.627233] smp: Bringing up secondary CPUs ...
|[ 0.681659] kernel tried to execute user page (0) - exploit attempt? (uid: 0)
|[ 0.766618] BUG: Unable to handle kernel instruction fetch (NULL pointer?)
|[ 0.848899] Faulting instruction address: 0x00000000
|[ 0.908273] Oops: Kernel access of bad area, sig: 11 [#1]
|[ 0.972851] BE PAGE_SIZE=4K SMP NR_CPUS=2 P1020 RDB
|[ 1.031179] Modules linked in:
|[ 1.067640] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.80 #0
|[ 1.139507] NIP: 00000000 LR: c0021d2c CTR: 00000000
|[ 1.199921] REGS: c1051cf0 TRAP: 0400 Not tainted (5.10.80)
|[...]
|[ 1.758220] NIP [00000000] 0x0
|[ 1.794688] LR [c0021d2c] smp_85xx_kick_cpu+0xe8/0x568
|[ 1.856126] Call Trace:
|[ 1.885295] [c1051da8] [c0021cb8] smp_85xx_kick_cpu+0x74/0x568 (unreliable)
|[ 1.968633] [c1051de8] [c0011460] __cpu_up+0xc0/0x228
|[ 2.029038] [c1051e18] [c0031bbc] bringup_cpu+0x30/0x224
|[ 2.092572] [c1051e48] [c0031f3c] cpu_up.constprop.0+0x180/0x33c
|[..]
|[ 2.727952] ---[ end trace 9b796a4bafb6bc14 ]---
|[ 3.800879] Kernel panic - not syncing: Fatal exception
|[ 3.862353] Rebooting in 1 seconds..
|[ 5.905097] System Halted, OK to turn off power
|
|I bisected this down to commit 3ae5da5adce9 ("kernel: bump 5.10 to 5.10.80");
|that is, I don't get the panic right before this commit, but I do after.
He reported the issue upstream and Xiaoming Ni from huawei came up with
the patch (that is on it's way to upstream). While the AP370 is not in
Openwrt, this will likely affect other SMP P1020 devices OpenWrt ships
with: like the AP330, Enterasys WS-AP3710i, etc.
Reported-by: Martin Kennedy <hurricos@gmail.com> Tested-by: Martin Kennedy <hurricos@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Wed, 17 Nov 2021 10:53:46 +0000 (11:53 +0100)]
ipq40xx: purge clk_ignore_unused bootarg
these flags have been creeping in from the QSDK.
All needed clocks should be accounted for, and
if a device is broken due to this. It should be
looked into.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Mathias Kresin [Sat, 27 Nov 2021 16:28:19 +0000 (17:28 +0100)]
lantiq: set maximum kernel size for P2812HNUF3
The board has a fixed size kernel partition but do not limit the kernel
size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Josef Schlehofer [Tue, 14 Sep 2021 12:40:54 +0000 (14:40 +0200)]
arm-trusted-firmware-mvebu: add cryptopp
Based on the Build Instructions for Trusted-Firmware-A [1],
there is a required cryptopp [2].
In the past, it used 'tbb_linux' image tool binary, which seems to
be buggy, deprecated and removed from A3700-utils-marvell and it should
not be used anymore. That's why I removed 001-imagetool.patch, which is
no longer necessary.
Kerma Gérald [Tue, 12 Oct 2021 11:25:32 +0000 (13:25 +0200)]
arm-trusted-firmware-mvebu: fix commit ids to for mv-ddr-marvell
without this patch a3700-utils/tim/ddr/ddr_tool.verstr contains the OpenWrt commit ID.
this patch fix the mv_ddr version commit ID by using the global variable MV_DDR_COMMIT_ID.
Upon boot it now prints "mv_ddr-devel-g02e23dbc-d DDR4 16b 1GB 1CS".
Cc: Andre Heider <a.heider@gmail.com> Signed-off-by: Kerma Gérald <gandalf@gk2.net>
Ansuel Smith [Thu, 18 Nov 2021 02:02:21 +0000 (03:02 +0100)]
ath10k-ct: use 5.15 version
We switched to mac80211 5.15 backport version.
Also switch ath10k-ct to 5.15 and drop the mac address patch
that got merged upstream.
Compile and tested on ipq806x Netgear R7800.
Also update the ath10k-ct to latest version to fix a typo
for the new version in the kernel log.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Sander Vanheule [Sun, 14 Nov 2021 18:45:34 +0000 (19:45 +0100)]
realtek: Remove _machine_restart and _machine_halt
By dropping _machine_restart, users can provide more reliable or
device-specific restart modes.
_machine_halt was already removed in commit f4b687d1f053 ("realtek: use
kernel defined halt"), but quietly reintroduced in commit 8faffa00cb6b
("realtek: add support for the RTL9300 timer"). Let's remove it again.
Sander Vanheule [Sun, 14 Nov 2021 18:45:33 +0000 (19:45 +0100)]
realtek: Add and enable watchdog node
Add and enable the Realtek Otto WDT peripheral found on these SoCs.
Default all devices to use standard (cold) reboot and "soc" resets.
Devices that require the PLL value fixup before restarting, should pick
the "cpu" or "software" reset mode. These devices also need to provide a
custom reboot mode, by adding the reboot argument to the kernel command
line:
WDT reset mode | kernel reboot mode
----------------+---------------------------------------
soc | reboot=cold (default if not specified)
cpu | reboot=warm
software | reboot=software
Preferrably, these devices should use an alternative restart method like
gpio-restart to provide reliable restarts.
Note that watchdog restarts are not yet exposed, since the
_machine_restart override is still present.
Sander Vanheule [Sun, 14 Nov 2021 18:45:32 +0000 (19:45 +0100)]
realtek: Backport Realtek Otto WDT driver
Add patch submitted upstream to linux-watchdog and replace the MIPS
architecture symbols. Requires one extra patch for the DIV_ROUND_*
macros, which have moved to a different header since 5.10.
Sander Vanheule [Sun, 14 Nov 2021 18:45:31 +0000 (19:45 +0100)]
realtek: Add Lexra bus clock
The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the
Lexra bus. This bus can provide a clock signal to these peripherals, but
no clock driver is currently available. Instead, use a fixed-clock to
provide the clock frequency, and update the dependent peripherals.
Sander Vanheule [Thu, 18 Nov 2021 17:39:18 +0000 (18:39 +0100)]
realtek: reset both ethernet NIC and queues
Recent versions of Realtek's SDK reset both the ethernet NIC and queues
(SW_NIC_RST and SW_Q_RST bits) when initialising the hardware.
Furthermore, when issuing a CPU reset on the Zyxel GS1900-8 (not
supported by any current driver), the networking part of the SoC is not
reset. This leads to unresponsive network after the restart. By
resetting both the ethernet NIC and queues, networking always comes up
reliably.
Felix Fietkau [Wed, 24 Nov 2021 16:02:26 +0000 (17:02 +0100)]
hostapd: add a patch that allows processing auth requests for peers in blocked state
If authentication fails repeatedly e.g. because of a weak signal, the link
can end up in blocked state. If one of the nodes tries to establish a link
again before it is unblocked on the other side, it will block the link to
that other side. The same happens on the other side when it unblocks the
link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in blocked
state, but don't initiate the attempt until the blocked period is over.
Felix Fietkau [Wed, 24 Nov 2021 09:45:28 +0000 (10:45 +0100)]
mac80211: fix regression in SSN handling of addba tx
Some drivers that do their own sequence number allocation (e.g. ath9k, mwlwifi) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Mark Mentovai [Tue, 23 Nov 2021 17:28:55 +0000 (12:28 -0500)]
hostapd: allow hostapd under ujail to communicate with hostapd_cli
When procd-ujail is available, 1f785383875a runs hostapd as user
"network", with only limited additional capabilities (CAP_NET_ADMIN and
CAP_NET_RAW).
hostapd_cli (CONFIG_PACKAGE_hostapd-utils) communicates with hostapd
over a named UNIX-domain socket. hostapd_cli is responsible for creating
this socket at /tmp/wpa_ctrl_$pid_$counter. Since it typically runs as
root, this endpoint is normally created with uid root, gid root, mode
0755. As a result, hostapd running as uid network is able to receive
control messages sent through this interface, but is not able to respond
to them. If debug-level logging is enabled (CONFIG_WPA_MSG_MIN_PRIORITY
<= 2 at build, and log_level <= 2 in /etc/config/wireless wifi-device),
this message will appear from hostapd:
CTRL: sendto failed: Permission denied
As a fix, hostapd_cli should create the socket node in the filesystem
with uid network, gid network, mode 0770. This borrows the presently
Android-only strategy already in hostapd intended to solve the same
problem on Android.
If procd-ujail is not available and hostapd falls back to running as
root, it will still be able to read from and write to the socket even if
the node in the filesystem has been restricted to the network user and
group. This matches the logic in
package/network/services/hostapd/files/wpad.init, which sets the uid and
gid of /var/run/hostapd to network regardless of whether procd-ujail is
available.
As it appears that the "network" user and group are statically allocated
uid 101 and gid 101, respectively, per
package/base-files/files/etc/passwd and USERID in
package/network/services/hostapd/Makefile, this patch also uses a
constant 101 for the uid and gid.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
[refreshed patch] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jo-Philipp Wich [Thu, 18 Nov 2021 12:00:09 +0000 (13:00 +0100)]
procd: setup /dev/stdin, /dev/stdout and /dev/stderr symlinks
Extend the hotplug.json ruleset to setup the common /dev/std{in,out,err}
symbolic links which are needed by some applications, e.g. nftables when
applying rulesets from stdin.
Daniel Golle [Tue, 23 Nov 2021 14:00:42 +0000 (14:00 +0000)]
procd: update to git HEAD
8de12de system: add diskfree infos to ubus bf3fe0e service: move jail parsing to end of instance parser 87b5836 procd: add full service shutdown prior to sysupgrade 01ac2c4 procd: service_stop_all: also kill inittab actions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rafał Miłecki [Tue, 23 Nov 2021 09:14:22 +0000 (10:14 +0100)]
bcm53xx: use new USB 2.0 PHY binding
This fixes:
[ 10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff]
[ 10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs
[ 10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16
caused by conflict in allocating resources.
Fixes: f55f1dbaad33 ("bcm53xx: switch to the kernel 5.10") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Mon, 22 Nov 2021 15:07:56 +0000 (16:07 +0100)]
mt76: update to the latest version
5dd32475c859 mt76: mt7915: get rid of mt7915_mcu_set_fixed_rate routine f5cfaaff3dd1 mt76: mt7921: drop offload_flags overwritten f5ad840ca5c0 mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy() 29a8a08827b1 mt76: mt7921: fix MT7921E reset failure f44685f2faee mt76: mt7915: fix return condition in mt7915_tm_reg_backup_restore() ae8e02ddd2b0 mt76: mt7915: fix SMPS operation fail e814e15716b0 mt76: reverse the first fragmented frame to 802.11 c9bca3ed9566 mt76: mt7915: fix NULL pointer dereference in mt7915_get_phy_mode dd054b7e16e7 mt76: only set rx radiotap flag from within decoder functions f1520c9bb332 mt76: mt7915: add default calibrated data support 0c489ea2865a mt76: testmode: add support to set MAC 91c5da3d0a7c mt76: mt7921: add support for PCIe ID 0x0608/0x0616 ca39b4bbc227 mt76: debugfs: fix queue reporting for mt76-usb 00b6f497e2e8 mt76: mt7921: introduce 160 MHz channel bandwidth support c1574466c733 mt76: fix possible OOB issue in mt76_calculate_default_rate 9680a17b0aed mt76: mt7921: fix possible NULL pointer dereference in mt7921_mac_write_txwi 78fc0dcdcef0 mt76: connac: fix a theoretical NULL pointer dereference in mt76_connac_get_phy_mode 05953e7d6fe7 mt76: mt7615: remove dead code in get_omac_idx 39f6c37127c1 mt76: connac: remove PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode 526591b203f3 mt76: do not pass the received frame with decryption error 256789bb400f mt76: fix the wiphy's available antennas to the correct value fa187f5cf068 mt76: fix timestamp check in tx_status 11ebf11a3587 mt76: mt7915: fix the wrong SMPS mode 8c69b815ee7f mt76: mt7921: honor mt76_connac_mcu_set_rate_txpower return value in mt7921_config bc6798f729f9 mt76: move sar utilities to mt76-core module b1d0ad2e74fe mt76: mt76x02: introduce SAR support
Daniel Golle [Sun, 21 Nov 2021 21:33:41 +0000 (21:33 +0000)]
sunxi: build kernel with sun6i-rtc driver
sun6i-rtc cannot be built as a module and the hardware is only
present in some of the sunxi SoCs, see driver source:
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
{ .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ .compatible = "allwinner,sun50i-h6-rtc" },
Set CONFIG_RTC_DRV_SUN6I=y in kernel config file for cortexa7 and
cortexa53 subtargets which covers all of the above.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Huangbin Zhan [Thu, 18 Nov 2021 11:37:10 +0000 (19:37 +0800)]
tools/llvm-bpf: make sure llvm-bpf.tar.gz is created
The llvm-bpf-$version.tar.xz might be absent. For example `make clean` executed, CONFIG_TARGET changed.
This commit can only guarantee that the target file can be built when tools/compile is explicitly called rather than $(tools/stamp-compile).
Sebastian Schaper [Wed, 25 Aug 2021 20:00:08 +0000 (22:00 +0200)]
ath79: move cal-data extraction to dts for DAP-2695
This device can be merged with the existing dtsi, which declares
the location of ath9k cal-data via devicetree, correcting the 2.4G
mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`.
To make these changes more visible, apply before merging with dtsi.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Jakob (Jack/XDjackieXD) [Sun, 7 Nov 2021 00:08:25 +0000 (01:08 +0100)]
ath79: add support for Mikrotik LHG 5
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and
RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi
integrated antenna built around the Atheros AR9344 SoC.
It is very similar to the SXT Lite5 series which this patch is based
upon.
this pwrseq need rtc clock, or kernel won't find this device.
but now rtc-sunxi.c only support A10/A20.
Orangepi Lite 2 use H6 ,from rtc-sun6i.c show compatible is
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
{ .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ .compatible = "allwinner,sun50i-h6-rtc" },
So it need this to let kernel find this mmc wifi device.
Roger Pueyo Centelles [Fri, 22 Oct 2021 10:19:40 +0000 (12:19 +0200)]
ath79: mikrotik: enable USB module on RouterBoard wAPR-2nD
The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e
slot with USB lines connected, which are used by some USB cards with
miniPCI-e form factor, like the R11e-LR8. Enabling USB support is
required for such cards to work.
Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
projects / users / dwmw2 / openwrt.git / log