wifi: iwlwifi: mvm: increase the time between ranging measurements
The algo running in fw may take a little longer than 5 milliseconds,
(e.g. measurement on 80MHz while associated). Increase the minimum
time between measurements to 7 milliseconds.
wifi: iwlwifi: mvm: set the cipher for secured NDP ranging
The cipher pointer is not set, but is derefereced trying to set its
content, which leads to a NULL pointer dereference.
Fix it by pointing to the cipher parameter before dereferencing.
Ilan Peer [Sun, 25 Aug 2024 05:56:37 +0000 (08:56 +0300)]
wifi: iwlwifi: mvm: Fix a race in scan abort flow
When the upper layer requests to cancel an ongoing scan, a race
is possible in which by the time the driver starts to handle the
upper layers scan cancel flow, the FW already completed handling
the scan request and the driver received the scan complete
notification but still did not handle the notification. In such a
case the FW will simply ignore the scan abort request coming from
the driver, no notification would arrive from the FW and the entire
abort flow would be considered a failure.
To better handle this, check the status code returned by the FW for
the scan abort command. In case the status indicates that
no scan was aborted, complete the scan abort flow with success, i.e.,
the scan was aborted, as the flow is expected to consume the scan
complete notification.
SAP version 4 uses larger Host to MEI notification queue.
Since it is unknown which SAP version is used by the CSME firmware
when the driver loads, try version 4 first. In case the CSME firmware
uses version 3, the memory allocation will fail. In this case the
driver will try again to allocate the memory for version 3.
Johannes Berg [Mon, 29 Jul 2024 17:20:07 +0000 (20:20 +0300)]
wifi: iwlwifi: config: label 'gl' devices as discrete
The 'gl' devices are in the bz family, but they're not,
integrated, so should have their own trans config struct.
Fix that, also necessitating the removal of LTR config,
and while at it remove 0x2727 and 0x272D IDs that were
only used for test chips.
Johannes Berg [Mon, 29 Jul 2024 17:20:06 +0000 (20:20 +0300)]
wifi: iwlwifi: pcie: print function scratch before writing
We may want to know the value of this register for certain
debug scenarios before we overwrite it, it indicates which
parts of the chip have recently been reset.
Johannes Berg [Mon, 29 Jul 2024 17:20:05 +0000 (20:20 +0300)]
wifi: iwlwifi: mvm: use correct key iteration
In the cases changed here, key iteration isn't done from
an RCU critical section, but rather using the wiphy lock
as protection. Therefore, just use ieee80211_iter_keys().
The link switch case can therefore also use sync commands.
wifi: iwlwifi: mvm: prepare the introduction of V9 of REDUCED_TX_POWER
* Rename iwl_dev_tx_power_cmd to iwl_dev_tx_power_cmd_v3_v8
* struct iwl_dev_tx_power_common needs to be packed. It was always the
case, but now that its size is not a multiple of 4, it becomes
meaningful.
* Move per_band data out of the common structure since it won't be
present in the new versions of the command.
wifi: mac80211: don't use rate mask for offchannel TX either
Like the commit ab9177d83c04 ("wifi: mac80211: don't use rate mask for
scanning"), ignore incorrect settings to avoid no supported rate warning
reported by syzbot.
The syzbot did bisect and found cause is commit 9df66d5b9f45 ("cfg80211:
fix default HE tx bitrate mask in 2G band"), which however corrects
bitmask of HE MCS and recognizes correctly settings of empty legacy rate
plus HE MCS rate instead of returning -EINVAL.
As suggestions [1], follow the change of SCAN TX to consider this case of
offchannel TX as well.
Introduce 'ieee80211_mgmt_ba()' to avoid code duplication between
'ieee80211_send_addba_resp()', 'ieee80211_send_addba_request()',
and 'ieee80211_send_delba()', ensure that all related addresses
are '__aligned(2)', and prefer convenient 'ether_addr_copy()'
over generic 'memcpy()'. No functional changes expected.
Zong-Zhe Yang [Fri, 12 Jul 2024 07:49:38 +0000 (15:49 +0800)]
wifi: mac80211_hwsim: correct MODULE_PARM_DESC of multi_radio
Correct the name field in multi_radio's MODULE_PARM_DESC.
Fixes: d2601e34a102 ("wifi: mac80211_hwsim: add support for multi-radio wiphy") Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Acked-by: Felix Fietkau <nbd@nbd.name> Link: https://patch.msgid.link/20240712074938.26437-1-kevin_yang@realtek.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sascha Hauer [Fri, 16 Aug 2024 06:56:10 +0000 (08:56 +0200)]
wifi: mwifiex: remove unnecessary checks for valid priv
The pointers in adapter->priv[] are allocated in mwifiex_register().
With an allocation failed the function will return an error and
driver initialization is aborted. This makes all checks for valid
priv pointers unnecessary throughout the driver. In many places
the pointers are assumed to be valid without checks, this patch
removes the remaining checks.
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `__struct_group()`
helper to create new tagged structures with the suffix `_hdr`.
These structures group together all the members of the original
flexible structures except the flexible arrays.
As a result, the arrays are effectively separated from the rest of the
members without modifying the memory layout of the flexible structures.
We then change the type of the middle struct members currently causing
trouble from the original flex struct to the newly created structs with
suffix `_hdr`.
We also want to ensure that when new members need to be added to the
flexible structures, they are always included within the newly created
tagged structs. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement the `_hdr` structures as
completely separate structures, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
We also use `container_of()` whenever we need to retrieve a pointer to
the flexible structure, through which we can access the flexible-array
member, if necessary.
Also, remove a couple of unused zero-length arrays and flexible-array
members.
So, with these changes, fix the following warnings:
drivers/net/wireless/intel/iwlegacy/commands.h:1196:38: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlegacy/commands.h:1197:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlegacy/commands.h:2505:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlegacy/commands.h:2549:26: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlegacy/commands.h:2654:31: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlegacy/commands.h:2665:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlegacy/commands.h:2673:26: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/iwlegacy/commands.h:3349:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Sascha Hauer [Fri, 9 Aug 2024 09:51:48 +0000 (11:51 +0200)]
wifi: mwifiex: keep mwifiex_cfg80211_ops constant
With host_mlme support being added mwifiex_cfg80211_ops is no longer
constant, but supplemented with the host_mlme related ops when host_mlme
support is enabled. This doesn't work with multiple adapters when only
few of then have host_mlme support. Duplicate mwifiex_cfg80211_ops
before using it and keep the original constant.
While at it mark mwifiex_cfg80211_ops const to prevent people from
changing it again during runtime.
Kalle Valo [Tue, 13 Aug 2024 09:58:32 +0000 (12:58 +0300)]
Merge tag 'ath-next-20240812' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.12
This is a fairly light pull request since ath12k is still working on
MLO-related changes, and the other drivers are mostly in maintenance
mode with a few cleanups and bug fixes.
Major changes:
ath12k
* DebugFS support for transmit DE stats
* Make ASPM support hardware-dependent
* Align BSS Channel information command and message with firmware
ath11k
* Use work queue for beacon tx events
ath9k
* Use devm for gpio_request_one
* Use unmanaged PCI functions in ath9k_pci_owl_loader()
Gustavo A. R. Silva [Thu, 8 Aug 2024 22:11:15 +0000 (16:11 -0600)]
wifi: mwl8k: Use static_assert() to check struct sizes
Commit 5c4250092fad ("wifi: mwl8k: Avoid -Wflex-array-member-not-at-end
warnings") introduced tagged `struct mwl8k_cmd_pkt_hdr`. We want to
ensure that when new members need to be added to the flexible structure,
they are always included within this tagged struct.
We use `static_assert()` to ensure that the memory layout for both
the flexible structure and the tagged struct is the same after any
changes.
Kalle Valo [Sat, 10 Aug 2024 07:42:26 +0000 (10:42 +0300)]
Merge tag 'rtw-next-2024-08-09' of https://github.com/pkshih/rtw
rtw-next patches for v6.12
A pull-request for v6.12 containing fixes and features, and list major
changes below:
rtw88:
- improve USB performance by aggregation
- fix RX bandwidth for rx_status
rtw89:
- support new WiFi 6 chip RTL8852BE-VT
- support WoWLAN net-detect feature
- support hardware encryption in unicast management frames
- support hardware rfkill
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `__struct_group()`
helper to create a new tagged `struct libipw_hdr_3addr_hdr`.
This structure groups together all the members of the flexible
`struct libipw_hdr_3addr` except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct libipw_hdr_3addr` to `struct libipw_hdr_3addr_hdr`.
We also want to ensure that when new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct libipw_hdr_3addr_hdr`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
Also, remove a couple of unused structures `struct libipw_ibss_dfs` and
`struct libipw_assoc_request`.
So, with these changes, fix the following warnings:
drivers/net/wireless/intel/ipw2x00/libipw.h:403:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:420:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:433:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:441:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:447:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:460:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:468:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:476:33: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:592:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Sascha Hauer [Mon, 5 Aug 2024 06:39:15 +0000 (08:39 +0200)]
wifi: mwifiex: add support for WPA-PSK-SHA256
This adds support for the WPA-PSK AKM suite with SHA256 as hashing
method (WPA-PSK-SHA256). Tested with a wpa_supplicant provided AP
using key_mgmt=WPA-PSK-SHA256.
Sascha Hauer [Mon, 5 Aug 2024 06:39:14 +0000 (08:39 +0200)]
wifi: mwifiex: fix key_mgmt setting
bss_config->key_mgmt specifies the AKM suites that are usable in
hardware. This variable is set to specific values while iterating
over the advertised AKM suites. This means the final value of the
variable depends on the order of the entries in the AKM suites
array. Instead of setting the variable, just set the relevant bits
in the key_mgmt bit field to make us independent of the order of
entries.
This behaviour is derived from the downstream driver that does the
same.
Also, set bss_config->key_mgmt to zero explicitly right before the
loop. bss_config has been zero allocated by the caller already, but
do so again to save the reader from following the code path.
Sascha Hauer [Mon, 5 Aug 2024 06:39:13 +0000 (08:39 +0200)]
wifi: mwifiex: simplify WPA flags setting
The WPA flags setting only depends on the wpa_versions bitfield and not
on the AKM suite, so move it out of the switch/case to simplify the code
a bit. Also set bss_config->protocol to zero explicitly. This is done
only to make the code clearer, bss_config has been zero alloced by the
caller, so should be zero already. No functional change intended.
Felix pointed out that moving to devm for request_irq() can lead to a use after
free, and that avoiding that means having explicit frees that makes the devm
thing pretty pointless. So let's just revert the patch.
Bitterblue Smith [Wed, 7 Aug 2024 22:23:06 +0000 (01:23 +0300)]
wifi: rtw88: Enable USB RX aggregation for 8822c/8822b/8821c
Enable USB RX aggregation when there is at least 1 Mbps RX or TX
traffic, otherwise disable it.
USB RX aggregation improves the RX speed of RTL8811CU on certain ARM
systems, like the NanoPi NEO Core2. Before: 28 Mbps, after: 231 Mbps.
It also improves the RX speed of RTL8822CU on some x86_64 systems.
Before: ~200 Mbps, after: ~300 Mbps.
The official drivers for these chips use the same logic for SDIO, but
for some reason the SDIO driver in rtw88 always enables RX aggregation,
so this patch only toggles aggregation for USB devices.
RTL8703B is likely not found in USB devices, and RTL8723DU doesn't like
aggregation.
Bitterblue Smith [Wed, 7 Aug 2024 22:21:36 +0000 (01:21 +0300)]
wifi: rtw88: usb: Support RX aggregation
The chips can be configured to aggregate several frames into a single
USB transfer. Modify rtw_usb_rx_handler() to support this case.
RX aggregation improves the RX speed of RTL8811CU on certain ARM
systems, like the NanoPi NEO Core2. It also improves the RX speed of
RTL8822CU on some x86_64 systems.
Currently none of the chips are configured to aggregate frames.
Peter Robinson [Tue, 6 Aug 2024 08:22:31 +0000 (09:22 +0100)]
wifi: rtl8xxxu: add missing rtl8192cu USB IDs
The rtl8xxxu has all the rtl8192cu USB IDs except for the
following 3 so add them to the untested section so they
can be used with the rtl8xxxu as the rtl8192cu are well
supported.
Peter Robinson [Mon, 5 Aug 2024 22:19:04 +0000 (23:19 +0100)]
wifi: rtl8xxxu: drop reference to staging drivers
The Kconfig notes mention staging drivers that have
since been removed so update the driver's description
so it no longer references the staging rtl8723au and
rtl8192u drivers which have now been deleted.
Chin-Yen Lee [Mon, 5 Aug 2024 09:00:27 +0000 (17:00 +0800)]
wifi: rtw89: wow: add delay option for net-detect
The delay option is the period in unit of second for WoWLAN firmware
to wait before the first scan. We get the option from cfg80211 and
practice it. Another, in some platform, WoWLAN firmware may found
configured network and then trigger resume process, before suspend
process is completed, lead to the wakeup function failed.
So the default value is set one to avoid the issue.
Chin-Yen Lee [Mon, 5 Aug 2024 09:00:26 +0000 (17:00 +0800)]
wifi: rtw89: wow: add WoWLAN net-detect support
Net-detect is an option of WoWLAN to allow the device to
be woken up from suspend mode when configured network is detected.
When user enables net-detect and lets the device enter suspend
state, WoWLAN firmware will periodically scan until beacon or
probe response of configured networks are received. If configured
networks are detected, WoWLAN firmware will trigger resume process.
Chin-Yen Lee [Mon, 5 Aug 2024 09:00:25 +0000 (17:00 +0800)]
wifi: rtw89: wow: implement PS mode for net-detect
When net-detect is enabled, WoWLAN firmware will periodically
scan until beacon or probe response of configured networks are
received. To reduce power consumption, the FW-IPS mode is
implemented to keep WiFi chip in idle mode between each scan.
The FW-IPS is controlled by WoWLAN firmware to turn of some critical
electrical components, and is different from the original IPS mode
which most electrical components are turned off.
Ping-Ke Shih [Mon, 5 Aug 2024 09:00:24 +0000 (17:00 +0800)]
wifi: rtw89: 8852c: support firmware format up to v1
Driver has supported different WoWLAN reason code by commit 0e5210217768
("wifi: rtw89: wow: update WoWLAN reason register for different FW")
since firmware version 0.27.80.0. The old driver can't support two
kinds of WoWLAN reason, so increase firmware format to v1.
Also driver tables of BB and RF registers and power values will be added
into v1 format.
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240331183232.2158756-3-quic_kathirve@quicinc.com
P Praneesh [Sun, 31 Mar 2024 18:32:31 +0000 (00:02 +0530)]
wifi: ath12k: fix BSS chan info request WMI command
Currently, the firmware returns incorrect pdev_id information in
WMI_PDEV_BSS_CHAN_INFO_EVENTID, leading to incorrect filling of
the pdev's survey information.
To prevent this issue, when requesting BSS channel information
through WMI_PDEV_BSS_CHAN_INFO_REQUEST_CMDID, firmware expects
pdev_id as one of the arguments in this WMI command.
Add pdev_id to the struct wmi_pdev_bss_chan_info_req_cmd and fill it
during ath12k_wmi_pdev_bss_chan_info_request(). This resolves the
issue of sending the correct pdev_id in WMI_PDEV_BSS_CHAN_INFO_EVENTID.
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240331183232.2158756-2-quic_kathirve@quicinc.com
wifi: ath12k: restore ASPM for supported hardwares only
During PCI based hardware device start up, ASPM is disabled for all. And
once firmware is ready, it is restored back. However, not all hardwares
(for example QCN9274) supports ASPM. Hence there is a need to conditionally
restore ASPM back. Or else, for such hardwares, issue can be seen during
sending and receiving packets.
Introduce a new hardware param supports_aspm which identifies whether a
given hardware supports ASPM or not and then accordingly restore it.
Toke Høiland-Jørgensen [Mon, 5 Aug 2024 11:02:22 +0000 (13:02 +0200)]
wifi: ath9k: Remove error checks when creating debugfs entries
We should not be checking the return values from debugfs creation at all: the
debugfs functions are designed to handle errors of previously called functions
and just transparently abort the creation of debugfs entries when debugfs is
disabled. If we check the return value and abort driver initialisation, we break
the driver if debugfs is disabled (such as when booting with debugfs=off).
Earlier versions of ath9k accidentally did the right thing by checking the
return value, but only for NULL, not for IS_ERR(). This was "fixed" by the two
commits referenced below, breaking ath9k with debugfs=off starting from the 6.6
kernel (as reported in the Bugzilla linked below).
Restore functionality by just getting rid of the return value check entirely.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219122 Fixes: 1e4134610d93 ("wifi: ath9k: use IS_ERR() with debugfs_create_dir()") Fixes: 6edb4ba6fb5b ("wifi: ath9k: fix parameter check in ath9k_init_debug()") Reported-by: Daniel Tobias <dan.g.tob@gmail.com> Tested-by: Daniel Tobias <dan.g.tob@gmail.com> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240805110225.19690-1-toke@toke.dk
wifi: rtw89: add support for HW encryption in unicast management frames
Add hardware encryption support for unicast management frames for
8922AE and 8852CE. Other chips will continue to use software
encryption for unicast management frames.
wifi: rtw89: avoid to add interface to list twice when SER
If SER L2 occurs during the WoWLAN resume flow, the add interface flow
is triggered by ieee80211_reconfig(). However, due to
rtw89_wow_resume() return failure, it will cause the add interface flow
to be executed again, resulting in a double add list and causing a kernel
panic. Therefore, we have added a check to prevent double adding of the
list.
wifi: rtw89: 8922a: Add new fields for scan offload H2C command
Update scan offload H2C format to fit firmware version 35.21.
The new fields indicate lengths of variable length members, so
when driver and firmware are using mismatch version, FW could
handle the parsing better.
Dmitry Kandybka [Thu, 1 Aug 2024 10:15:31 +0000 (13:15 +0300)]
wifi: brcmsmac: clean up unnecessary current_ampdu_cnt and related checks
In 'brcms_c_ffpld_check_txfunfl()', 'current_ampdu_cnt' is hardcoded to
zero, so 'txunfl_ratio' is always zero as well and some dead code can be
removed. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
When the firmware interface layer was refactored it provided various
"get" and "set" functions. For the "get" in some cases a parameter
needed to be passed down to firmware as a key indicating what to
"get" turning the output parameter of the "get" function into an
input parameter as well. To accommodate this the "get" function blindly
copies the parameter which in some places resulted in an uninitialized
warnings from the compiler. These have been fixed by initializing the
input parameter in the past. Recently another batch of similar fixes
were submitted to address clang static checker warnings [1].
Proposing another solution by introducing a "query" variant which is used
when the (input) parameter is needed by firmware. The "get" variant will
only fill the (output) parameter with the result received from firmware
taking care of proper endianess conversion.
wifi: brcmfmac: fwsignal: Use struct_size() to simplify brcmf_fws_rxreorder()
In the "struct brcmf_ampdu_rx_reorder", change the 'pktslots' field into
flexible array.
It saves the size of a pointer when the memory is allocated and avoids
an indirection when the array is used.
It also removes the usage of a pointer arithmetic and saves a few lines of
code.
Finally, struct_size() can be used. It is not a must have here, because
it is easy to see that buf_size can not overflow, but still, it is a good
practice.
David Lin [Thu, 4 Jul 2024 03:30:01 +0000 (11:30 +0800)]
wifi: mwifiex: add host mlme for AP mode
Add host based MLME to enable WPA3 functionalities in AP mode.
This feature required a firmware with the corresponding V2 Key API
support. The feature (WPA3) is currently enabled and verified only
on IW416. Also, verified no regression with change when host MLME
is disabled.
Signed-off-by: David Lin <yu-hao.lin@nxp.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Acked-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240704033001.603419-3-yu-hao.lin@nxp.com
David Lin [Thu, 4 Jul 2024 03:30:00 +0000 (11:30 +0800)]
wifi: mwifiex: add host mlme for client mode
Add host based MLME to enable WPA3 functionalities in client mode.
This feature required a firmware with the corresponding V2 Key API
support. The feature (WPA3) is currently enabled and verified only
on IW416. Also, verified no regression with change when host MLME
is disabled.
Signed-off-by: David Lin <yu-hao.lin@nxp.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Acked-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240704033001.603419-2-yu-hao.lin@nxp.com
Sascha Hauer [Thu, 30 May 2024 13:01:56 +0000 (15:01 +0200)]
wifi: mwifiex: increase max_num_akm_suites
The maximum number of AKM suites will be set to two if not specified by
the driver. Set it to CFG80211_MAX_NUM_AKM_SUITES to let userspace
specify up to ten AKM suites in the akm_suites array.
Without only the first two AKM suites will be used, further ones are
ignored.
Zong-Zhe Yang [Sat, 27 Jul 2024 08:06:50 +0000 (16:06 +0800)]
wifi: rtw89: pass chanctx_idx to rtw89_btc_{path_}phymap()
Originally, rtw89_btc_phymap() and rtw89_btc_path_phymap() access chan
with hard-code RTW89_CHANCTX_0. But, they are problematic when the chip
supports multiple channels.
So, change their prototype and pass chanctx_idx ahead. Let callers still
pass RTW89_CHANCTX_0 for now, but we will refine callers in the following.
Zong-Zhe Yang [Sat, 27 Jul 2024 08:06:49 +0000 (16:06 +0800)]
wifi: rtw89: fw: correct chan access in assoc_cmac_tbl_g7 and update_beacon_be
Originally, these H2C commands access chan with hard-code RTW89_CHANCTX_0.
They are problematic when the chip supports multiple channels. So, correct
them by accessing right chan under rtwvif.
Zong-Zhe Yang [Sat, 27 Jul 2024 08:06:46 +0000 (16:06 +0800)]
wifi: rtw89: rename sub_entity to chanctx
Originally, we planed to fill MAC_0/1 indicators with chanctx and
use sub_entity_xxx for these things. However, there are some reasons
listed below which make us give up this plan after we know our Wi-Fi 7
HW design.
1. one link is bound to one HW band during its life time
but, one link might change chanctx dynamically
2. in concurrent mode, assume 1st vif is MLD
1st vif's 2nd link might use the same chanctx as 2nd vif
but, they are not on the same HW band
So, we let sub_entity_xxx stuffs deal with only chanctx now. And, to be
more readable, we rename sub_entity related words to chanctx.
Zong-Zhe Yang [Sat, 27 Jul 2024 08:06:45 +0000 (16:06 +0800)]
wifi: rtw89: mcc: stop at a role holding chanctx
In general, MCC (multi-channel concurrency) stops when some chanctx is
unassigned. Originally, we let FW to stop at a fixed role. However, it
might be the one to be unassigned.
So, iterate MCC roles and select one which is still holding chanctx.
Zong-Zhe Yang [Sat, 27 Jul 2024 08:06:44 +0000 (16:06 +0800)]
wifi: rtw89: chan: refine MCC re-plan flow when unassign chanctx
Originally during unassign-chanctx, MCC (multi-channel concurrency) is
re-planed before set-channel if need. But, we might calculate MCC stuffs
based on old channel info. And, the following set-channel might be racing
with FW MCC state mechanism. So, we refine this flow. Now, if MCC re-plan
is needed here, it will be done after set-channel.
Besides, to be more rigorous, we now ensure entity isn't paused before we
deal with MCC things here.
wifi: rtw88: always wait for both firmware loading attempts
In 'rtw_wait_firmware_completion()', always wait for both (regular and
wowlan) firmware loading attempts. Otherwise if 'rtw_usb_intf_init()'
has failed in 'rtw_usb_probe()', 'rtw_usb_disconnect()' may issue
'ieee80211_free_hw()' when one of 'rtw_load_firmware_cb()' (usually
the wowlan one) is still in progress, causing UAF detected by KASAN.
For different firmware type, it could change IDMEM mode, so reset it to
default to avoid encountering error for RTL8851B/RTL8852B/RTL8852BT
if that kind of firmware was downloaded before.
rtw89_8851be 0000:02:00.0: Firmware version 0.29.41.3, cmd version 0, type 5
rtw89_8851be 0000:02:00.0: Firmware version 0.29.41.3, cmd version 0, type 3
rtw89_8851be 0000:02:00.0: MAC has already powered on
rtw89_8851be 0000:02:00.0: fw security fail
rtw89_8851be 0000:02:00.0: download firmware fail
rtw89_8851be 0000:02:00.0: [ERR]fwdl 0x1E0 = 0x62
rtw89_8851be 0000:02:00.0: [ERR]fwdl 0x83F2 = 0x8
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f51c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f524
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f51c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f500
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f51c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f53c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f520
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f520
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f508
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f534
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f520
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f534
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f508
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f53c
rtw89_8851be 0000:02:00.0: [ERR]fw PC = 0xb892f524
rtw89_8851be 0000:02:00.0: failed to setup chip information
rtw89_8851be: probe of 0000:02:00.0 failed with error -16
To more accurately debug performance issues, EVM statistics will
differentiate between different space streams, and only beacon
and data frames will be included.
wifi: rtw88: 8822c: Parse channel from IE to correct invalid hardware reports
For CCK packets we could get incorrect reports from hardware.
And this causes wrong frequencies being reported. Parse the channel
information from IE if provided by AP to fix this.
wifi: ath9k: use unmanaged PCI functions in ath9k_pci_owl_loader
Only managed PCI resource in the driver is the iomapped bar. However the bar
is unmapped in the same function. Therefore using the device-managed
versions just causes overhead, w/o any benefit. Once this is switched to the
non-managed versions, there's nothing left to be managed for
pcim_enable_device(). Therefore we can reduce overhead here too and switch to
the non-managed version as well. This includes removing the no longer needed
call to pcim_pin_device().
Bitterblue Smith [Tue, 23 Jul 2024 19:31:36 +0000 (22:31 +0300)]
wifi: rtw88: 8822c: Fix reported RX band width
"iw dev wlp2s0 station dump" shows incorrect rx bitrate:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 86.7 MBit/s VHT-MCS 9 VHT-NSS 1
This is because the RX band width is calculated incorrectly. Fix the
calculation according to the phydm_rxsc_2_bw() function from the
official drivers.
After:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 390.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 1
It also works correctly with the AP configured for 20 MHz and 40 MHz.
Add chip_info of RTL8852BT accordingly, including power on/off function,
BB reset, TSSI settings while setting channel, RF calibration, and
BT coexistence.
Add chip_info of RTL8852BT accordingly, including firmware elements
support, MAC memory quota (WDE, PLE and etc), SER IMR used by firmware,
BTC registers, register based H2C/C2H, WoWLAN stub.
wifi: rtw89: 8852bt: rfk: use predefined string choice for DPK enable/disable
clang warns precedence of '?:' and '&'. Even though original logic is
correct, use str_enable_disable() to avoid clang confusing. Another way to
fix is to add parentheses around '&', but I choose former one.
>> drivers/net/wireless/realtek/rtw89/rtw8852bt_rfk.c:1827:46: warning:
operator '?:' has lower precedence than '&'; '&' will be evaluated
first [-Wbitwise-conditional-parentheses]
1827 | kidx, dpk->is_dpk_enable & off_reverse ? "enable" : "disable");
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
wifi: rtw88: debugfs: support multiple adapters debugging
Originally in order to read partial registers from large area, we write
a range value stored into a static variable and read registers according
to the static variable.
However, if we install more than one adapters supported by this driver,
the static variables will be overwritten by latter adapters. To resolve
the problem, move the static variables to struct rtw_dev for each adapter.
With changes, smatch spends too much time to parse rtw_debugfs_init():
debug.c:1289 rtw_debugfs_init() parse error: turning off implications
after 60 seconds
Move stuffs of adding debugfs entries to three rtw_debugfs_add_xxx()
functions.
Reported-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Closes: https://lore.kernel.org/linux-wireless/cd6a2acf3c2c36d938b40140b52a779516f446a9.camel@realtek.com/T/#m27662022c70d9f893ba96f6c6a8dd8fce2434dfe Tested-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20240718064155.38955-1-pkshih@realtek.com
Merge tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix RPM package build error caused by an incorrect locale setup
- Mark modules.weakdep as ghost in RPM package
- Fix the odd combination of -S and -c in stack protector scripts,
which is an error with the latest Clang
* tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Fix '-S -c' in x86 stack protector scripts
kbuild: rpm-pkg: ghost modules.weakdep file
kbuild: rpm-pkg: Fix C locale setup
minmax: simplify and clarify min_t()/max_t() implementation
This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.
That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.
Cc: David Laight <David.Laight@aculab.com> Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3a7e02c040b1 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
kbuild: Fix '-S -c' in x86 stack protector scripts
After a recent change in clang to stop consuming all instances of '-S'
and '-c' [1], the stack protector scripts break due to the kernel's use
of -Werror=unused-command-line-argument to catch cases where flags are
not being properly consumed by the compiler driver:
$ echo | clang -o - -x c - -S -c -Werror=unused-command-line-argument
clang: error: argument unused during compilation: '-c' [-Werror,-Wunused-command-line-argument]
This results in CONFIG_STACKPROTECTOR getting disabled because
CONFIG_CC_HAS_SANE_STACKPROTECTOR is no longer set.
'-c' and '-S' both instruct the compiler to stop at different stages of
the pipeline ('-S' after compiling, '-c' after assembling), so having
them present together in the same command makes little sense. In this
case, the test wants to stop before assembling because it is looking at
the textual assembly output of the compiler for either '%fs' or '%gs',
so remove '-c' from the list of arguments to resolve the error.
All versions of GCC continue to work after this change, along with
versions of clang that do or do not contain the change mentioned above.
Cc: stable@vger.kernel.org Fixes: 4f7fd4d7a791 ("[PATCH] Add the -fstack-protector option to the CFLAGS") Fixes: 60a5317ff0f4 ("x86: implement x86_32 stack protector") Link: https://github.com/llvm/llvm-project/commit/6461e537815f7fa68cef06842505353cf5600e9c Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Merge tag 'v6.11-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Enable turbostat extensions to add both perf and PMT (Intel
Platform Monitoring Technology) counters via the cmdline
- Demonstrate PMT access with built-in support for Meteor Lake's
Die C6 counter
* tag 'v6.11-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2024.07.26
tools/power turbostat: Include umask=%x in perf counter's config
tools/power turbostat: Document PMT in turbostat.8
tools/power turbostat: Add MTL's PMT DC6 builtin counter
tools/power turbostat: Add early support for PMT counters
tools/power turbostat: Add selftests for added perf counters
tools/power turbostat: Add selftests for SMI, APERF and MPERF counters
tools/power turbostat: Move verbose counter messages to level 2
tools/power turbostat: Move debug prints from stdout to stderr
tools/power turbostat: Fix typo in turbostat.8
tools/power turbostat: Add perf added counter example to turbostat.8
tools/power turbostat: Fix formatting in turbostat.8
tools/power turbostat: Extend --add option with perf counters
tools/power turbostat: Group SMI counter with APERF and MPERF
tools/power turbostat: Add ZERO_ARRAY for zero initializing builtin array
tools/power turbostat: Replace enum rapl_source and cstate_source with counter_source
tools/power turbostat: Remove anonymous union from rapl_counter_info_t
tools/power/turbostat: Switch to new Intel CPU model defines
Merge tag 'cxl-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL updates from Dave Jiang:
"Core:
- A CXL maturity map has been added to the documentation to detail
the current state of CXL enabling.
It provides the status of the current state of various CXL features
to inform current and future contributors of where things are and
which areas need contribution.
- A notifier handler has been added in order for a newly created CXL
memory region to trigger the abstract distance metrics calculation.
This should bring parity for CXL memory to the same level vs
hotplugged DRAM for NUMA abstract distance calculation. The
abstract distance reflects relative performance used for memory
tiering handling.
- An addition for XOR math has been added to address the CXL DPA to
SPA translation.
CXL address translation did not support address interleave math
with XOR prior to this change.
Fixes:
- Fix to address race condition in the CXL memory hotplug notifier
- Add missing MODULE_DESCRIPTION() for CXL modules
- Fix incorrect vendor debug UUID define
Misc:
- A warning has been added to inform users of an unsupported
configuration when mixing CXL VH and RCH/RCD hierarchies
- The ENXIO error code has been replaced with EBUSY for inject poison
limit reached via debugfs and cxl-test support
- Moving the PCI config read in cxl_dvsec_rr_decode() to avoid
unnecessary PCI config reads
- A refactor to a common struct for DRAM and general media CXL
events"
* tag 'cxl-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/core/pci: Move reading of control register to immediately before usage
cxl: Remove defunct code calculating host bridge target positions
cxl/region: Verify target positions using the ordered target list
cxl: Restore XOR'd position bits during address translation
cxl/core: Fold cxl_trace_hpa() into cxl_dpa_to_hpa()
cxl/test: Replace ENXIO with EBUSY for inject poison limit reached
cxl/memdev: Replace ENXIO with EBUSY for inject poison limit reached
cxl/acpi: Warn on mixed CXL VH and RCH/RCD Hierarchy
cxl/core: Fix incorrect vendor debug UUID define
Documentation: CXL Maturity Map
cxl/region: Simplify cxl_region_nid()
cxl/region: Support to calculate memory tier abstract distance
cxl/region: Fix a race condition in memory hotplug notifier
cxl: add missing MODULE_DESCRIPTION() macros
cxl/events: Use a common struct for DRAM and General Media events
Merge tag 'unicode-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krisman/unicode
Pull unicode update from Gabriel Krisman Bertazi:
"Two small fixes to silence the compiler and static analyzers tools
from Ben Dooks and Jeff Johnson"
* tag 'unicode-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krisman/unicode:
unicode: add MODULE_DESCRIPTION() macros
unicode: make utf8 test count static
In the same way as for other similar files, mark as ghost the new file
generated by depmod for configured weak dependencies for modules,
modules.weakdep, so that although it is not included in the package,
claim the ownership on it.
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Merge tag '6.11-rc-smb-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix for potential null pointer use in init cifs
- additional dynamic trace points to improve debugging of some common
scenarios
- two SMB1 fixes (one addressing reconnect with POSIX extensions, one a
mount parsing error)
* tag '6.11-rc-smb-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: add dynamic trace point for session setup key expired failures
smb3: add four dynamic tracepoints for copy_file_range and reflink
smb3: add dynamic tracepoint for reflink errors
cifs: mount with "unix" mount option for SMB1 incorrectly handled
cifs: fix reconnect with SMB1 UNIX Extensions
cifs: fix potential null pointer use in destroy_workqueue in init_cifs error path
Merge tag 'block-6.11-20240726' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fix request without payloads cleanup (Leon)
- Use new protection information format (Francis)
- Improved debug message for lost pci link (Bart)
- Another apst quirk (Wang)
- Use appropriate sysfs api for printing chars (Markus)
- ublk async device deletion fix (Ming)
- drbd kerneldoc fixups (Simon)
- Fix deadlock between sd removal and release (Yang)
* tag 'block-6.11-20240726' of git://git.kernel.dk/linux:
nvme-pci: add missing condition check for existence of mapped data
ublk: fix UBLK_CMD_DEL_DEV_ASYNC handling
block: fix deadlock between sd_remove & sd_release
drbd: Add peer_device to Kernel doc
nvme-core: choose PIF from QPIF if QPIFS supports and PIF is QTYPE
nvme-pci: Fix the instructions for disabling power management
nvme: remove redundant bdev local variable
nvme-fabrics: Use seq_putc() in __nvmf_concat_opt_tokens()
nvme/pci: Add APST quirk for Lenovo N60z laptop
Merge tag 'vfs-6.11-rc1.fixes.3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"This contains two fixes for this merge window:
VFS:
- I noticed that it is possible for a privileged user to mount most
filesystems with a non-initial user namespace in sb->s_user_ns.
When fsopen() is called in a non-init namespace the caller's
namespace is recorded in fs_context->user_ns. If the returned file
descriptor is then passed to a process privileged in init_user_ns,
that process can call fsconfig(fd_fs, FSCONFIG_CMD_CREATE*),
creating a new superblock with sb->s_user_ns set to the namespace
of the process which called fsopen().
This is problematic as only filesystems that raise FS_USERNS_MOUNT
are known to be able to support a non-initial s_user_ns. Others may
suffer security issues, on-disk corruption or outright crash the
kernel. Prevent that by restricting such delegation to filesystems
that allow FS_USERNS_MOUNT.
Note, that this delegation requires a privileged process to
actually create the superblock so either the privileged process is
cooperaing or someone must have tricked a privileged process into
operating on a fscontext file descriptor whose origin it doesn't
know (a stupid idea).
The bug dates back to about 5 years afaict.
Misc:
- Fix hostfs parsing when the mount request comes in via the legacy
mount api.
In the legacy mount api hostfs allows to specify the host directory
mount without any key.
Restore that behavior"
* tag 'vfs-6.11-rc1.fixes.3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
hostfs: fix the host directory parse when mounting.
fs: don't allow non-init s_user_ns for filesystems without FS_USERNS_MOUNT
Merge tag 'rust-6.11' of https://github.com/Rust-for-Linux/linux
Pull Rust updates from Miguel Ojeda:
"The highlight is the establishment of a minimum version for the Rust
toolchain, including 'rustc' (and bundled tools) and 'bindgen'.
The initial minimum will be the pinned version we currently have, i.e.
we are just widening the allowed versions. That covers three stable
Rust releases: 1.78.0, 1.79.0, 1.80.0 (getting released tomorrow),
plus beta, plus nightly.
This should already be enough for kernel developers in distributions
that provide recent Rust compiler versions routinely, such as Arch
Linux, Debian Unstable (outside the freeze period), Fedora Linux,
Gentoo Linux (especially the testing channel), Nix (unstable) and
openSUSE Slowroll and Tumbleweed.
In addition, the kernel is now being built-tested by Rust's pre-merge
CI. That is, every change that is attempting to land into the Rust
compiler is tested against the kernel, and it is merged only if it
passes. Similarly, the bindgen tool has agreed to build the kernel in
their CI too.
Thus, with the pre-merge CI in place, both projects hope to avoid
unintentional changes to Rust that break the kernel. This means that,
in general, apart from intentional changes on their side (that we will
need to workaround conditionally on our side), the upcoming Rust
compiler versions should generally work.
In addition, the Rust project has proposed getting the kernel into
stable Rust (at least solving the main blockers) as one of its three
flagship goals for 2024H2 [1].
I would like to thank Niko, Sid, Emilio et al. for their help
promoting the collaboration between Rust and the kernel.
Toolchain and infrastructure:
- Support several Rust toolchain versions.
- Support several bindgen versions.
- Remove 'cargo' requirement and simplify 'rusttest', thanks to
'alloc' having been dropped last cycle.
- Provide proper error reporting for the 'rust-analyzer' target.
'kernel' crate:
- Add 'uaccess' module with a safe userspace pointers abstraction.
- Add 'page' module with a 'struct page' abstraction.
- Support more complex generics in workqueue's 'impl_has_work!'
macro.
'macros' crate:
- Add 'firmware' field support to the 'module!' macro.
- Improve 'module!' macro documentation.
Documentation:
- Provide instructions on what packages should be installed to build
the kernel in some popular Linux distributions.
- Introduce the new kernel.org LLVM+Rust toolchains.
- Explain '#[no_std]'.
And a few other small bits"
Link: https://rust-lang.github.io/rust-project-goals/2024h2/index.html#flagship-goals
* tag 'rust-6.11' of https://github.com/Rust-for-Linux/linux: (26 commits)
docs: rust: quick-start: add section on Linux distributions
rust: warn about `bindgen` versions 0.66.0 and 0.66.1
rust: start supporting several `bindgen` versions
rust: work around `bindgen` 0.69.0 issue
rust: avoid assuming a particular `bindgen` build
rust: start supporting several compiler versions
rust: simplify Clippy warning flags set
rust: relax most deny-level lints to warnings
rust: allow `dead_code` for never constructed bindings
rust: init: simplify from `map_err` to `inspect_err`
rust: macros: indent list item in `paste!`'s docs
rust: add abstraction for `struct page`
rust: uaccess: add typed accessors for userspace pointers
uaccess: always export _copy_[from|to]_user with CONFIG_RUST
rust: uaccess: add userspace pointers
kbuild: rust-analyzer: improve comment documentation
kbuild: rust-analyzer: better error handling
docs: rust: no_std is used
rust: alloc: add __GFP_HIGHMEM flag
rust: alloc: fix typo in docs for GFP_NOWAIT
...
projects / users / jedix / linux-maple.git / log