Avid Adrenaline is reported that ALSA firewire-digi00x driver is bound to.
However, as long as he investigated, the design of this model is hardly
similar to the one of Digi 00x family. It's better to exclude the model
from modalias of ALSA firewire-digi00x driver.
This commit changes device entries so that the model is excluded.
When system is suspended with active audio playback to HDMI/DP, two
alternative sequences can happen at resume:
a) monitor is detected first and ALSA prepare follows normal
stream setup sequence, or
b) ALSA prepare is called first, but monitor is not yet detected,
so PCM is restarted without a pin,
In case of (b), on i915 systems, haswell_verify_D0() is not called at
resume and the pin power state may be incorrect. Result is lack of audio
after resume with no error reported back to user-space.
Fix the problem by always verifying converter and pin state in the
i915_pin_cvt_fixup().
The PCM OSS mulaw plugin has a check of the format of the counter part
whether it's a linear format. The check is with snd_BUG_ON() that
emits WARN_ON() when the debug config is set, and it confuses
syzkaller as if it were a serious issue. Let's drop snd_BUG_ON() for
avoiding that.
While we're at it, correct the error code to a more suitable, EINVAL.
snd_ca0106_spi_write() returns 1 on error, snd_ca0106_pcm_power_dac()
is returning the error code directly, and the caller is expecting an
negative error code
The problem is we're doing a copy_to_user() while holding tree locks,
which can deadlock if we have to do a page fault for the copy_to_user().
This exists even without my locking changes, so it needs to be fixed.
Rework the search ioctl to do the pre-fault and then
copy_to_user_nofault for the copying.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3d7081822f7f ("uaccess: Add non-pagefault user-space read functions")
missed to add probe write function, therefore factor out a probe_write_common()
helper with most logic of probe_kernel_write() except setting KERNEL_DS, and
add a new probe_user_write() helper so it can be used from BPF side.
Again, on some archs, the user address space and kernel address space can
co-exist and be overlapping, so in such case, setting KERNEL_DS would mean
that the given address is treated as being in kernel address space.
Add probe_user_read(), strncpy_from_unsafe_user() and
strnlen_unsafe_user() which allows caller to access user-space
in IRQ context.
Current probe_kernel_read() and strncpy_from_unsafe() are
not available for user-space memory, because it sets
KERNEL_DS while accessing data. On some arch, user address
space and kernel address space can be co-exist, but others
can not. In that case, setting KERNEL_DS means given
address is treated as a kernel address space.
Also strnlen_user() is only available from user context since
it can sleep if pagefault is enabled.
To access user-space memory without pagefault, we need
these new functions which sets USER_DS while accessing
the data.
These are special extent buffers that get rewound in order to lookup
the state of the tree at a specific point in time. As such they do not
go through the normal initialization paths that set their lockdep class,
so handle them appropriately when they are created and before they are
locked.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a rewound buffer is created it already has a ref count of 1 and the
dummy flag set. Then another ref is taken bumping the count to 2.
Finally when this buffer is released from btrfs_release_path the extra
reference is decremented by the special handling code in
free_extent_buffer.
However, this special code is in fact redundant sinca ref count of 1 is
still correct since the buffer is only accessed via btrfs_path struct.
This paves the way forward of removing the special handling in
free_extent_buffer.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
get_old_root used used only by btrfs_search_old_slot to initialise the
path structure. The old root is always a cloned buffer (either via alloc
dummy or via btrfs_clone_extent_buffer) and its reference count is 2: 1
from allocation, 1 from extent_buffer_get call in get_old_root.
This latter explicit ref count acquire operation is in fact unnecessary
since the semantic is such that the newly allocated buffer is handed
over to the btrfs_path for lifetime management. Considering this just
remove the extra extent_buffer_get in get_old_root.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Accessing the disabled memory space of a PCI device would typically
result in a master abort response on conventional PCI, or an
unsupported request on PCI express. The user would generally see
these as a -1 response for the read return data and the write would be
silently discarded, possibly with an uncorrected, non-fatal AER error
triggered on the host. Some systems however take it upon themselves
to bring down the entire system when they see something that might
indicate a loss of data, such as this discarded write to a disabled
memory space.
To avoid this, we want to try to block the user from accessing memory
spaces while they're disabled. We start with a semaphore around the
memory enable bit, where writers modify the memory enable state and
must be serialized, while readers make use of the memory region and
can access in parallel. Writers include both direct manipulation via
the command register, as well as any reset path where the internal
mechanics of the reset may both explicitly and implicitly disable
memory access, and manipulation of the MSI-X configuration, where the
MSI-X vector table resides in MMIO space of the device. Readers
include the read and write file ops to access the vfio device fd
offsets as well as memory mapped access. In the latter case, we make
use of our new vma list support to zap, or invalidate, those memory
mappings in order to force them to be faulted back in on access.
Our semaphore usage will stall user access to MMIO spaces across
internal operations like reset, but the user might experience new
behavior when trying to access the MMIO space while disabled via the
PCI command register. Access via read or write while disabled will
return -EIO and access via memory maps will result in a SIGBUS. This
is expected to be compatible with known use cases and potentially
provides better error handling capabilities than present in the
hardware, while avoiding the more readily accessible and severe
platform error responses that might otherwise occur.
Fixes: CVE-2020-12888 Reviewed-by: Peter Xu <peterx@redhat.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[Ajay: Regenerated the patch for v4.19] Signed-off-by: Ajay Kaher <akaher@vmware.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rather than calling remap_pfn_range() when a region is mmap'd, setup
a vm_ops handler to support dynamic faulting of the range on access.
This allows us to manage a list of vmas actively mapping the area that
we can later use to invalidate those mappings. The open callback
invalidates the vma range so that all tracking is inserted in the
fault handler and removed in the close handler.
Reviewed-by: Peter Xu <peterx@redhat.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[Ajay: Regenerated the patch for v4.19] Signed-off-by: Ajay Kaher <akaher@vmware.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With conversion to follow_pfn(), DMA mapping a PFNMAP range depends on
the range being faulted into the vma. Add support to manually provide
that, in the same way as done on KVM with hva_to_pfn_remapped().
Reviewed-by: Peter Xu <peterx@redhat.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[Ajay: Regenerated the patch for v4.19] Signed-off-by: Ajay Kaher <akaher@vmware.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This problem exists because we have two different rescan threads,
btrfs_uuid_scan_kthread which creates the uuid tree, and
btrfs_uuid_tree_iterate that goes through and updates or deletes any out
of date roots. The problem is they both do things in different order.
btrfs_uuid_scan_kthread() reads the tree_root, and then inserts entries
into the uuid_root. btrfs_uuid_tree_iterate() scans the uuid_root, but
then does a btrfs_get_fs_root() which can read from the tree_root.
It's actually easy enough to not be holding the path in
btrfs_uuid_scan_kthread() when we add a uuid entry, as we already drop
it further down and re-start the search when we loop. So simply move
the path release before we add our entry to the uuid tree.
This also fixes a problem where we're holding a path open after we do
btrfs_end_transaction(), which has it's own problems.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the xfs filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted xfs filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the ext2 filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted ext2 filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
Otherwise gcc generates warnings if the expression is complicated.
Fixes: 312a0c170945 ("[PATCH] LOG2: Alter roundup_pow_of_two() so that it can use a ilog2() on a constant") Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Link: https://lkml.kernel.org/r/0-v1-8a2697e3c003+41165-log_brackets_jgg@nvidia.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54d7 ("staging: omap-thermal: add OMAP4 data structures") Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The VT-d spec requires (10.4.4 Global Command Register, GCMD_REG General
Description) that:
If multiple control fields in this register need to be modified, software
must serialize the modifications through multiple writes to this register.
However, in irq_remapping.c, modifications of IRE and CFI are done in one
write. We need to do two separate writes with STS checking after each. It
also checks the status register before writing command register to avoid
unnecessary register write.
Fixes: af8d102f999a4 ("x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess") Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: Kevin Tian <kevin.tian@intel.com> Cc: Ashok Raj <ashok.raj@intel.com> Link: https://lore.kernel.org/r/20200828000615.8281-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com> Reported-by: Baptiste Covolato <baptiste@arista.com> Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The realtime flag only applies to the data fork, so don't use the
realtime block number checks on the attr fork of a realtime file.
Fixes: 30b0984d9117 ("xfs: refactor bmap record validation") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
epoll_loop_check_proc() can run into a file already committed to destruction;
we can't grab a reference on those and don't need to add them to the set for
reverse path check anyway.
Tested-by: Marc Zyngier <maz@kernel.org> Fixes: a9ed4a6560b8 ("epoll: Keep a reference on files added to the check list") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
perf_event.h has macros that define the field offsets in the data_src
bitmask in perf records. The SNOOPX and REMOTE offsets were both 37.
These are distinct fields, and the bitfield layout in perf_mem_data_src
confirms that SNOOPX should be at offset 38.
Committer notes:
This was extracted from a larger patch that also contained kernel
changes.
Fixes: 52839e653b5629bd ("perf tools: Add support for printing new mem_info encodings") Signed-off-by: Al Grant <al.grant@arm.com> Reviewed-by: Andi Kleen <ak@linux.intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/9974f2d0-bf7f-518e-d9f7-4520e5ff1bb0@foss.arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Frontend callback reports EAGAIN to nfnetlink to retry a command, this
is used to signal that module autoloading is required. Unfortunately,
nlmsg_unicast() reports EAGAIN in case the receiver socket buffer gets
full, so it enters a busy-loop.
This patch updates nfnetlink_unicast() to turn EAGAIN into ENOBUFS and
to use nlmsg_unicast(). Remove the flags field in nfnetlink_unicast()
since this is always MSG_DONTWAIT in the existing code which is exactly
what nlmsg_unicast() passes to netlink_unicast() as parameter.
Fixes: 96518518cc41 ("netfilter: add nftables") Reported-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When stdout output from the selftests tool 'test_maps' gets redirected
into e.g file or pipe, then the output lines increase a lot (from 21
to 33949 lines). This is caused by the printf that happens before the
fork() call, and there are user-space buffered printf data that seems
to be duplicated into the forked process.
To fix this fflush() stdout before the fork loop in __run_parallel().
Reported-by: Rob Sherwood <rsher@fb.com> Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The boundary test for the fixed-offset parts of xfs_attr_sf_entry in
xfs_attr_shortform_verify is off by one, because the variable array
at the end is defined as nameval[1] not nameval[].
Hence we need to subtract 1 from the calculation.
This can be shown by:
# touch file
# setfattr -n root.a file
and verifications will fail when it's written to disk.
This only matters for a last attribute which has a single-byte name
and no value, otherwise the combination of namelen & valuelen will
push endp further out and this test won't fail.
Fixes: 1e1bbd8e7ee06 ("xfs: create structure verifier function for shortform xattrs") Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9bb ("bnxt_en: Add hwmon sysfs support to read temperature") Cc: Marc Smith <msmith626@gmail.com> Reported-by: Marc Smith <msmith626@gmail.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd2d ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.") Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
During a dump, this attribute is essential, it enables the userspace to
know on which interface the context is linked to.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the burst len fixup after setting the generic value for it. This
finally enables the fixup introduced by commit 137bd11090d8 ("dmaengine:
pl330: Align DMA memcpy operations to MFIFO width"), which otherwise was
overwritten by the generic value.
Reported-by: kernel test robot <lkp@intel.com> Fixes: 137bd11090d8 ("dmaengine: pl330: Align DMA memcpy operations to MFIFO width") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20200825064617.16193-1-m.szyprowski@samsung.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.
Fixes: 1bddd96cba03d ("net: arc_emac: support the phy reset for emac driver") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8eb6 ("net: systemport: Dynamically allocate number of TX rings") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aaf1b ("net: hns: net: hns: enet adds support of acpi") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Note the non-zero upper bits of the first element. It turns out that
nft_immediate doesn't zero the destination register, but this is needed
when the length isn't a multiple of 4.
Furthermore, the zeroing in nft_payload is broken. We can't use
[len / 4] = 0 -- if len is a multiple of 4, index is off by one.
Skip zeroing in this case and use a conditional instead of (len -1) / 4.
Fixes: 49499c3e6e18 ("netfilter: nf_tables: switch registers to 32 bit addressing") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernel sends an empty NFTA_SET_USERDATA attribute with no value if
userspace adds a set with no NFTA_SET_USERDATA attribute.
Fixes: e6d8ecac9e68 ("netfilter: nf_tables: Add new attributes into nft_set to store user data.") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The initialization done by bmips_cpu_setup() typically affects both
threads of a given core, on 7435 which supports 2 cores and 2 threads,
logical CPU number 2 and 3 would not run this initialization.
Fixes: 738a3f79027b ("MIPS: BMIPS: Add early CPU initialization code") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the BMIPS generic cpu-feature-overrides.h file was introduced,
cpu_has_inclusive_caches/MIPS_CPU_INCLUSIVE_CACHES was not set for
BMIPS5000 CPUs. Correct this when we have initialized the MIPS secondary
cache successfully.
batadv_bla_send_claim() gets called from worker thread context through
batadv_bla_periodic_work(), thus netif_rx_ni needs to be used in that
case. This fixes "NOHZ: local_softirq_pending 08" log messages seen
when batman-adv is enabled.
Fixes: 23721387c409 ("batman-adv: add basic bridge loop avoidance code") Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The own OGM check is currently misplaced and can lead to the following
issues:
For one thing we might receive an aggregated OGM from a neighbor node
which has our own OGM in the first place. We would then not only skip
our own OGM but erroneously also any other, following OGM in the
aggregate.
For another, we might receive an OGM aggregate which has our own OGM in
a place other then the first one. Then we would wrongly not skip this
OGM, leading to populating the orginator and gateway table with ourself.
The gateway client code can try to optimize the delivery of DHCP packets to
avoid broadcasting them through the whole mesh. But also transmissions to
the client can be optimized by looking up the destination via the chaddr of
the DHCP packet.
But the chaddr is currently only done when chaddr is fully inside the
non-paged area of the skbuff. Otherwise it will not be initialized and the
unoptimized path should have been taken.
But the implementation didn't handle this correctly. It didn't retrieve the
correct chaddr but still tried to perform the TT lookup with this
uninitialized memory.
Reported-by: syzbot+ab16e463b903f5a37036@syzkaller.appspotmail.com Fixes: 6c413b1c22a2 ("batman-adv: send every DHCP packet as bat-unicast") Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some architectures (like ARM), virt_to_gfn cannot be used for
vmalloc'd memory because of its reliance on virt_to_phys. This patch
introduces a check for vmalloc'd addresses and obtains the PFN using
vmalloc_to_pfn in that case.
Since commit a21ee6055c30 ("lockdep: Change hardirq{s_enabled,_context}
to per-cpu variables") the lockdep code itself uses percpu variables. This
leads to recursions because the percpu macros are calling preempt_enable()
which might call trace_preempt_on().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Marco Elver <elver@google.com> Link: https://lkml.kernel.org/r/20200821085348.251340558@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Leases don't currently work correctly on kcephfs, as they are not broken
when caps are revoked. They could eventually be implemented similarly to
how we did them in libcephfs, but for now don't allow them.
[ idryomov: no need for simple_nosetlease() in ceph_dir_fops and
ceph_snapdir_fops ]
clang static analysis reports this representative problem
applesmc.c:758:10: warning: 1st function call argument is an
uninitialized value
left = be16_to_cpu(*(__be16 *)(buffer + 6)) >> 2;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
buffer is filled by the earlier call
ret = applesmc_read_key(LIGHT_SENSOR_LEFT_KEY, ...
This problem is reported because a goto skips the status check.
Other similar problems use data from applesmc_read_key before checking
the status. So move the checks to before the use.
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Henrik Rydberg <rydberg@bitmath.org> Link: https://lore.kernel.org/r/20200820131932.10590-1-trix@redhat.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Define shutdown callback for display drm driver,
so as to disable all the CRTCS when shutdown
notification is received by the driver.
This change will turn off the timing engine so
that no display transactions are requested
while mmu translations are getting disabled
during reboot sequence.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Changes in v2:
- Remove NULL check from msm_pdev_shutdown (Stephen Boyd)
- Change commit text to reflect when this issue
was uncovered (Sai Prakash Ranjan)
Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When booting with heavily modularized config, the serial console
may not be able to load until after init when modules that
satisfy needed dependencies have time to load.
Unfortunately, as qcom_geni_console_setup is marked as __init,
the function may have been freed before we get to run it,
causing boot time crashes such as:
(scatter|gather)_data_area() need to flush dcache after writing data to or
before reading data from a page in uio data area. The two routines are
able to handle data transfer to/from such a page in fragments and flush the
cache after each fragment was copied by calling the wrapper
tcmu_flush_dcache_range().
That means:
1) flush_dcache_page() can be called multiple times for the same page.
2) Calling flush_dcache_page() indirectly using the wrapper does not make
sense, because each call of the wrapper is for one single page only and
the calling routine already has the correct page pointer.
Change (scatter|gather)_data_area() such that, instead of calling
tcmu_flush_dcache_range() before/after each memcpy, it now calls
flush_dcache_page() before unmapping a page (when writing is complete for
that page) or after mapping a page (when starting to read the page).
After this change only calls to tcmu_flush_dcache_range() for addresses in
vmalloc'ed command ring are left over.
The patch was tested on ARM with kernel 4.19.118 and 5.7.2
Link: https://lore.kernel.org/r/20200618131632.32748-2-bstroesser@ts.fujitsu.com Tested-by: JiangYu <lnsyyj@hotmail.com> Tested-by: Daniel Meyerholt <dxm523@gmail.com> Acked-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) If remaining ring space before the end of the ring is smaller then the
next cmd to write, tcmu writes a padding entry which fills the remaining
space at the end of the ring.
Then tcmu calls tcmu_flush_dcache_range() with the size of struct
tcmu_cmd_entry as data length to flush. If the space filled by the
padding was smaller then tcmu_cmd_entry, tcmu_flush_dcache_range() is
called for an address range reaching behind the end of the vmalloc'ed
ring.
tcmu_flush_dcache_range() in a loop calls
flush_dcache_page(virt_to_page(start)); for every page being part of the
range. On x86 the line is optimized out by the compiler, as
flush_dcache_page() is empty on x86.
But I assume the above can cause trouble on other architectures that
really have a flush_dcache_page(). For paddings only the header part of
an entry is relevant due to alignment rules the header always fits in
the remaining space, if padding is needed. So tcmu_flush_dcache_range()
can safely be called with sizeof(entry->hdr) as the length here.
2) After it has written a command to cmd ring, tcmu calls
tcmu_flush_dcache_range() using the size of a struct tcmu_cmd_entry as
data length to flush. But if a command needs many iovecs, the real size
of the command may be bigger then tcmu_cmd_entry, so a part of the
written command is not flushed then.
Link: https://lore.kernel.org/r/20200528193108.9085-1-bstroesser@ts.fujitsu.com Acked-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Event modifiers are not mentioned in the perf record or perf stat
manpages. Add them to orient new users more effectively by pointing
them to the perf list manpage for details.
Fixes: 2055fdaf8703 ("perf list: Document precise event sampling for AMD IBS") Signed-off-by: Kim Phillips <kim.phillips@amd.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paul Clarke <pc@us.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Tony Jones <tonyj@suse.de> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/20200901215853.276234-1-kim.phillips@amd.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling into hid_map_usage(), the passed event code is
blindly stored as is, even if it doesn't fit in the associated bitmap.
This event code can come from a variety of sources, including devices
masquerading as input devices, only a bit more "programmable".
Instead of taking the event code at face value, check that it actually
fits the corresponding bitmap, and if it doesn't:
- spit out a warning so that we know which device is acting up
- NULLify the bitmap pointer so that we catch unexpected uses
Code paths that can make use of untrusted inputs can now check
that the mapping was indeed correct and bail out if not.
Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that a ReportSize value of zero is legal, even if a bit
non-sensical. Most of the HID code seems to handle that gracefully,
except when computing the total size in bytes. When fed as input to
memset, this leads to some funky outcomes.
Detect the corner case and correctly compute the size.
Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the buffers for storing context's and sessions can vary from
arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the
maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be
enough for most use with three handles (that is how many we allow at the
moment). Parametrize the buffer size while doing this, so that it is easier
to revisit this later on if required.
Cc: stable@vger.kernel.org Reported-by: Stefan Berger <stefanb@linux.ibm.com> Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
With my new locking code dbench is so much faster that I tripped over a
transaction abort from ENOSPC. This turned out to be because
btrfs_del_dir_entries_in_log was checking for ret == -ENOSPC, but this
function sets err on error, and returns err. So instead of properly
marking the inode as needing a full commit, we were returning -ENOSPC
and aborting in __btrfs_unlink_inode. Fix this by checking the proper
variable so that we return the correct thing in the case of ENOSPC.
The ENOENT needs to be checked, because btrfs_lookup_dir_item_index()
can return -ENOENT if the dir item isn't in the tree log (which would
happen if we hadn't fsync'ed this guy). We actually handle that case in
__btrfs_unlink_inode, so it's an expected error to get back.
Fixes: 4a500fd178c8 ("Btrfs: Metadata ENOSPC handling for tree log") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ add note and comment about ENOENT ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdc-acm.c:409:3: warning: Use of memory after it is freed
acm_process_notification(acm, (unsigned char *)dr);
There are three problems, the first one is that dr is not reset
The variable dr is set with
if (acm->nb_index)
dr = (struct usb_cdc_notification *)acm->notification_buffer;
But if the notification_buffer is too small it is resized with
if (acm->nb_size) {
kfree(acm->notification_buffer);
acm->nb_size = 0;
}
alloc_size = roundup_pow_of_two(expected_size);
/*
* kmalloc ensures a valid notification_buffer after a
* use of kfree in case the previous allocation was too
* small. Final freeing is done on disconnect.
*/
acm->notification_buffer =
kmalloc(alloc_size, GFP_ATOMIC);
dr should point to the new acm->notification_buffer.
The second problem is any data in the notification_buffer is lost
when the pointer is freed. In the normal case, the current data
is accumulated in the notification_buffer here.
Inadvertently the commit b1cd1b65afba ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Brooke Basile <brookebasile@gmail.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Brooke Basile <brookebasile@gmail.com> Acked-by: Felipe Balbi <balbi@kernel.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com> Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure") Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Cyril Roelandt <tipecaml@gmail.com> Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
There's another Raydium touchscreen needs the no-lpm quirk:
[ 1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00
[ 1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.339151] usb 1-9: Product: Raydium Touch System
[ 1.339152] usb 1-9: Manufacturer: Raydium Corporation
...
[ 6.450497] usb 1-9: can't set config #1, error -110
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
The syzbot fuzzer identified a bug in the yurex driver: It passes
GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time
when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING:
The values for "se_num" and "sh_num" come from the user in the ioctl.
They can be in the 0-255 range but if they're more than
AMDGPU_GFX_MAX_SE (4) or AMDGPU_GFX_MAX_SH_PER_SE (2) then it results in
an out of bounds read.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Fixes: 927abfc4461e7 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain") Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org # v4.18+ Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the CPU mask operations behave the same way, but for_each_cpu() and
it's variants ignore the cpumask argument and claim that CPU0 is always in
the mask. This is historical, inconsistent and annoying behaviour.
The matrix allocator uses for_each_cpu() and can be called on UP with an
empty cpumask. The calling code does not expect that this succeeds but
until commit e027fffff799 ("x86/irq: Unbreak interrupt affinity setting")
this went unnoticed. That commit added a WARN_ON() to catch cases which
move an interrupt from one vector to another on the same CPU. The warning
triggers on UP.
Add a check for the cpumask being empty to prevent this.
When the primary firmware node pointer is removed from a
device (set to NULL) the secondary firmware node pointer,
when it exists, is made the primary node for the device.
However, the secondary firmware node pointer of the original
primary firmware node is never cleared (set to NULL).
To avoid situation where the secondary firmware node pointer
is pointing to a non-existing object, clearing it properly
when the primary node is removed from a device in
set_primary_fwnode().
Fixes: 97badf873ab6 ("device property: Make it possible to use secondary firmware nodes") Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been reported that system-wide suspend may be aborted in the
absence of any wakeup events due to unforseen interactions of it with
the runtume PM framework.
One failing scenario is when there are multiple devices sharing an
ACPI power resource and runtime-resume needs to be carried out for
one of them during system-wide suspend (for example, because it needs
to be reconfigured before the whole system goes to sleep). In that
case, the runtime-resume of that device involves turning the ACPI
power resource "on" which in turn causes runtime-resume requests
to be queued up for all of the other devices sharing it. Those
requests go to the runtime PM workqueue which is frozen during
system-wide suspend, so they are not actually taken care of until
the resume of the whole system, but the pm_runtime_barrier()
call in __device_suspend() sees them and triggers system wakeup
events for them which then cause the system-wide suspend to be
aborted if wakeup source objects are in active use.
Of course, the logic that leads to triggering those wakeup events is
questionable in the first place, because clearly there are cases in
which a pending runtime resume request for a device is not connected
to any real wakeup events in any way (like the one above). Moreover,
it is racy, because the device may be resuming already by the time
the pm_runtime_barrier() runs and so if the driver doesn't take care
of signaling the wakeup event as appropriate, it will be lost.
However, if the driver does take care of that, the extra
pm_wakeup_event() call in the core is redundant.
Accordingly, drop the conditional pm_wakeup_event() call fron
__device_suspend() and make the latter call pm_runtime_barrier()
alone. Also modify the comment next to that call to reflect the new
code and extend it to mention the need to avoid unwanted interactions
between runtime PM and system-wide device suspend callbacks.
Fixes: 1e2ef05bb8cf8 ("PM: Limit race conditions between runtime PM and system sleep (v2)") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com> Tested-by: Utkarsh H Patel <utkarsh.h.patel@intel.com> Tested-by: Pengfei Xu <pengfei.xu@intel.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
handler data is meant for interrupt handlers and not for storing irq chip
specific information as some devices require handler data to store internal
per interrupt information, e.g. pinctrl/GPIO chained interrupt handlers.
This obviously creates a conflict of interests and crashes the machine
because the XEN pointer is overwritten by the driver pointer.
As the XEN data is not handler specific it should be stored in
irqdesc::irq_data::chip_data instead.
A simple sed s/irq_[sg]et_handler_data/irq_[sg]et_chip_data/ cures that.
Cc: stable@vger.kernel.org Reported-by: Roman Shaposhnik <roman@zededa.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Roman Shaposhnik <roman@zededa.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/87lfi2yckt.fsf@nanos.tec.linutronix.de Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we are processing writeback for sync(2), move_expired_inodes()
didn't set any inode expiry value (older_than_this). This can result in
writeback never completing if there's steady stream of inodes added to
b_dirty_time list as writeback rechecks dirty lists after each writeback
round whether there's more work to be done. Fix the problem by using
sync(2) start time is inode expiry value when processing b_dirty_time
list similarly as for ordinarily dirtied inodes. This requires some
refactoring of older_than_this handling which simplifies the code
noticeably as a bonus.
Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") CC: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inode's i_io_list list head is used to attach inode to several different
lists - wb->{b_dirty, b_dirty_time, b_io, b_more_io}. When flush worker
prepares a list of inodes to writeback e.g. for sync(2), it moves inodes
to b_io list. Thus it is critical for sync(2) data integrity guarantees
that inode is not requeued to any other writeback list when inode is
queued for processing by flush worker. That's the reason why
writeback_single_inode() does not touch i_io_list (unless the inode is
completely clean) and why __mark_inode_dirty() does not touch i_io_list
if I_SYNC flag is set.
However there are two flaws in the current logic:
1) When inode has only I_DIRTY_TIME set but it is already queued in b_io
list due to sync(2), concurrent __mark_inode_dirty(inode, I_DIRTY_SYNC)
can still move inode back to b_dirty list resulting in skipping
writeback of inode time stamps during sync(2).
2) When inode is on b_dirty_time list and writeback_single_inode() races
with __mark_inode_dirty() like:
writeback_single_inode() __mark_inode_dirty(inode, I_DIRTY_PAGES)
inode->i_state |= I_SYNC
__writeback_single_inode()
inode->i_state |= I_DIRTY_PAGES;
if (inode->i_state & I_SYNC)
bail
if (!(inode->i_state & I_DIRTY_ALL))
- not true so nothing done
We end up with I_DIRTY_PAGES inode on b_dirty_time list and thus
standard background writeback will not writeback this inode leading to
possible dirty throttling stalls etc. (thanks to Martijn Coenen for this
analysis).
Fix these problems by tracking whether inode is queued in b_io or
b_more_io lists in a new I_SYNC_QUEUED flag. When this flag is set, we
know flush worker has queued inode and we should not touch i_io_list.
On the other hand we also know that once flush worker is done with the
inode it will requeue the inode to appropriate dirty list. When
I_SYNC_QUEUED is not set, __mark_inode_dirty() can (and must) move inode
to appropriate dirty list.
Reported-by: Martijn Coenen <maco@android.com> Reviewed-by: Martijn Coenen <maco@android.com> Tested-by: Martijn Coenen <maco@android.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log